Dimensions in inches and (millimeters)
Version: A06
SF1001G - SF1008G
10.0 AMPS. Glass Passivated Super Fast Rectifiers
TO-220AB
Features
High efficiency, low VF
High current capability
High reliability
High surge current capability
Low power loss.
For use in low voltage, high frequency inventor, free
wheeling, and polarity protection application
Mechanical Data
Case: TO-220AB Molded plastic
Epoxy: UL 94V-0 rate flame retardant
Terminals: Pure tin plated, lead free. solderable per
MIL-STD-202, Method 208 guaranteed
Polarity: As marked
High temperature soldering guaranteed:
260
oC/10 seconds .16”,(4.06mm) from case.
Weight: 2.24 grams
Maximum Ratings and Electrical Characteristics
Rating at 25 oC ambient temperature unless otherwise specified.
Single phase, half wave, 60 Hz, resistive or inductive load.
For capacitive load, derate current by 20%
Type Number Symbol SF
1001G
SF
1002G
SF
1003G
SF
1004G
SF
1005G
SF
1006G
SF
1007G
SF
1008G Units
Maximum Recurrent Peak Reverse Voltage VRRM 50 100 150 200 300 400 500 600 V
Maximum RMS Voltage VRMS 35 70 105 140 210 280 350 420 V
Maximum DC Blocking Voltage VDC 50 100 150 200 300 400 500 600 V
Maximum Average Forward Rectified
Current .375 (9.5mm) Lead Length
@TC = 100 oC
I(AV) 10.0 A
Peak Forward Surge Current, 8.3 ms Single
Half Sine-wave Superimposed on Rated
Load (JEDEC method )
IFSM 125 A
Maximum Instantaneous Forward Voltage
@ 5.0A VF 0.975 1.3 1.7
V
Maximum DC Reverse Current
@ TA=25 oC at Rated DC Blocking Voltage
@ TA=100 oC
IR 10.0
400
uA
uA
Maximum Reverse Recovery Time
(Note 1) Trr 35
nS
Typical Junction Capacitance (Note 2) Cj 70 50
pF
Typical Thermal Resistance (Note 3) RθJC 3.5
oC/W
Operating Temperature Range TJ -65 to +150 oC
Storage Temperature Range TSTG -65 to +150 oC
Notes: 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A
2. Measured at 1 MHz and Applied Reverse Voltage of 4.0 V D.C.
3. Mounted on Heatsink Size of 2” x 3” x 0.25” Al-plate.
FIG.6- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM
50
NONINDUCTIVE
NON
INDUCTIVE
OSCILLOSCOPE
(NOTE 1)
PULSE
GENERATOR
(NOTE 2)
DUT
(+)
50Vdc
(approx)
(-)
NOTES: 1. Rise Time=7ns max. Input Impedance=
1 megohm 22pf
2. Rise Time=10ns max. Sourse Impedance=
50 ohms
(-)
(+)
10
NONINDUCTIVE
-1.0A
-0.25A
0
+0.5A
trr
1cm SET TIME BASE FOR
5/ 10ns/ cm
RATINGS AND CHARACTERISTIC CURVES (SF1001G THRU SF1008G)
FIG.1- MAXIMUM FORWARD CURRENT DERATING
CURVE
AVERAGE FORWARD CURRENT. (A)
050 100 150
0
4
8
12
16
20
CASE TEMPERATURE. ( C)
o
FIG.5- TYPICAL FORWARD CHARACTERISTICS
PER LEG
INSTANTANEOUS FORWARD CURRENT. (A)
0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8
0.01
0.1
0.03
1
0.3
10
3
30
100
FORWARD VOLTAGE. (V)
Tj=25 C
Pulse Width=300 s
1% Duty Cycle
o
SF1001G~SF1004G
SF1005G~SF1006G
SF1007G~SF1008G
FIG.3- MAXIMUM NON-REPETITIVE FORWARD SURGE
CURRENT PER LEG
PEAK FORWARD SURGE CURRENT. (A)
12 5 10 20 10050
NUMBER OF CYCLES AT 60Hz
TJ=125 C
0
8.3ms Single Half Sine Wave
JEDEC Method
150
120
90
60
30
0
FIG.4- TYPICAL JUNCTION CAPACITANCE PER LEG
CAPACITANCE.(pF)
152 10 20 50 100 200 500
50
60
70
80
90
100
REVERSE VOLTAGE. (V)
Tj=25 C
0
SF1001G~SF1004G
SF1005G~SF1008G
40 1000
FIG.2- TYPICAL REVERSE CHARACTERISTICS
020 40 60 80 100 120 140
1000
0.1
1
10
100
PERCENT OF RATED PEAK REVERSE VOLTAGE. (%)
TJ=25 C
0
TJ=100 C
0
INSTANTANEOUS REVERSE CURRENT.( A)
TJ=75 C
0
Version: A06
