The Micro Line - .050" Contact Spacing The Cannon MICRO Series established the standards for performance and reliability in mircominiature interconnects. Exceptionally versatile, MICRO connectors are available in rectangular, circular, and strip configurations, with 3 amp MICROPINTM/ MICROSOCkETTM contacts on .050(1.27) centers, or with special arrangements of power and coaxial contacts. The heart of the Cannon MICROPIN/MICROSOCKET contact system is a multi-element Twist Pin Contact recessed with and insulating housing. The rugged, cylindrical sockets are mounted in the exposed half of the connector. When connector halves are mated, the chamfered sockets are first aligned by the connector body, then guide the spiral MICROPIN contacts into proper and positive alignment, even under worst-case tolerance conditions. This is Cannon's POS-A-LINE connectors design. The multiple spring elements of the MICROPIN, then under compression, form a multi-point contact system of high mechanical and electrical integrity. Contacts will provide a high degree of reliability over hundreds of mating and unmating cycles, and have proven themselves in applications that range from commercial products to equipment that has been landed on the moon. * Contact rating - 3 amps max. * Contacts centers - .050(1.27). * Wire sizes - #24 thru #32 AWG, stranded or solid. * Contact termination - multiple indent crimp. * Contact retention -fixed via epoxy. * Contact materials and finish - Copper alloy, gold-plated per MIL-G-45204, Type II, Grade C, Class 1 over copper flash. * Mating/unmating force - 8 oz. per contact, max./0.5 oz. per contact min. Test Data The table below summarizes the results of key tests performed in accordance with MIL-STD-1344, where applicable. Data is applicable to standard connectors with standard termination. Variations may affect this data, so please consult the factory for further information on your requirements. Test Method Dielectric Withstanding Voltage Method 3001: 900 VAC at sea level 300 VAC at 70,00' altitude Solder Pots and Shielded Cable 600 VAC at sea level 150 VAC at 70,000' altitude Criteria of Acceptance No breakdown No breakdown No breakdown No breakdown Insulation Resistance Method 3003 5,000 megohms minimum Thermal Shock Method 1003. Condition A: - 55C to +125C No physical damage Physical Shock Method 2004, Condition E: 50 G's, 3 axes, 6 millisecond duration sawtooth pulse No physical damage No loss of continuity > 1 sec Vibration Method 2005, Condition IV: 20 G's, 10-2,000 Hz. 12 hrs No physical damage No loss of continuity > 1 sec Durability 500 cycles of mating and unmating, 500 CPH max. No mechanical or electrical defects Moisture Resistance Method 1002, Type II omit steps 7a & 7B Insulation resistance > 100 megohms Salt Spray Method 1001, Condition B: 48 hours Shall be cable of mating and unmating, and meet contact resistance requirements Contact Resistance (MIL-STD-202) Method 307 At 3 amps At 1 milliamps 8 milliohms maximum 10 milliohms maximum Contact Retention Per MIL-C-83513 5 lb. minimum axial load Dimensions are shown in inches (millimeters). Dimensions subject to change. www.ittcannon.com 231 Micro-D Metal Shell - .050" Contact Spacing MDM MDM connectors are used in applications requiring highly reliable, extremely small, lightweight connectors with higher density contact configurations than available in traditional rectangular connectors. They are available in 8 shell sizes accommodating from 9 to 100 contacts, and special arrangements of power and coaxial contacts. PIN/MICROSOCKET contacts on .050(1.27_ centers in a contact density identical to the standard MICRO-D connector series, but with these additional features: These connectors are designed to meet the rapidly increasing demands for an environmental, high performance, rugged, moisture-sealed microminiature connector. This connector employs size 24 MICRO- Silicone elastomer compression interfacial seal to provide a moisture and humidity seal between each contact and between contacts and shell. Aluminum shells to provide greater strength, prevent chipping, cracking or breaking, offer electromagnetic (EMI) and RFI shielding. How to Order MIL-C-83513 ordering information- pages 240 and 241 MDM - 51 P H 001 P - XXX SERIES CONTACT ARRANGEMENTS CONTACT TYPE TERMINATION TYPE TERMINATION CODE HARDWARE SHELL FINISH MOD CODES SERIES TERMINATION CODE* MDM (size 9-100): Liquid Crystal Ploymer (LCP) MDM (Combo Layout): Diallyl Phthalate insulator Material CONTACT ARRANGEMENTS 9-15-21-25-31-37-51-100 (standard) 7C2, 24C42 (coaxial) or combination of 7P2, 24P4 (power) coax and power } CONTACT TYPE P - Pin S - Socket TERMINATION TYPE H - Harness-insulated wire. L - Solid-uninsulated wire. S - Solder pot to accept #26 AWG MAX. harness wire. (Not available with power contact arrangements.) (H) 001 - 18",7/34 strand,#26 AWG, MIL-W-16878/4, Type E Teflon, yellow. (H) 003 - 18", 7/34 strand, #26 AWG, MIL-W-16878/4, Type E Teflon, color coded to MIL-STD-681 System I. (L) 1 - 1/2" uninsulated solid #25 AWG gold plated copper. (L) 2 - 1" uninsulated solid #25 AWG gold plated copper. HARDWARE M - Military specification hardware, see page 237. P - Jackpost K - Jackscrew-standard L - Jackscrew-low profile F - Float mount B - No hardware standard .091 (2.31) dia. hole for sizes 9-51; .120 (3.05) dia. hole for size 100. A - .125 (3.18) dia. mounting holes fo sizes 9-51; .166 (4.22) dia. hole for size 100. B1 - .1475 (3.75) dia. hole for size 100 (Per MIL-C-83513) SHELL FINISH MOD CODES** No Number - Standard Cadmium/yellow chromate A174 - Electroless nickel A172 - Gold over nickel A141 - Irridite/alodine A30 - Black anodize *See Termination Codes page 233 for additional length Modification codes. **For other modifications not listed, consult the factory. Performance and Material Specifications STANDARD MATERIALS AND FINISHES MECHANICAL FEATURES Shell Coupling - Friction/jackscrews Polarization - Keystone-shaped shells Contact Spacing Centers - .050 (1.27) Shell Styles - Plug and receptacle No. of Contacts - 9 thru 100 standard; 5 signal/2 coaxial; 5 signal/2 power. 20 signal/4 coaxial; 20 signal/4 power Coaxial Cable - RG - 178/U Wire Size - #24 thru #32 AWG Contact Termination - Multiple indent crimp - Aluminum alloy per QQ-A-200/8 (6061-T6), yellow chromate/cadmium per QQ-P-416, Type II, class 3. Insulator - MIL-M-24519, Type GLCP-30F Glass-filled diallyl phthalate per MIL-M-14, Type SDGF Contacts - Copper alloy, gold plate Mounting Hardware - 300 Series stainless steel, passivate Kit, Jackpost (3) items - 300 Series stainless steel, passivate Washer - 400 Series stainless stell, passivate Standard Epoxy - Hysol EE4198 with HD3561 hardener, color green or EE4215 with HD3561, color black ELECTRICAL DATA - page 231 Dimensions are shown in inches (millimeters). Dimensions subject to change. www.ittcannon.com 232 Micro-D Metal Shell - .050" Contact Spacing MDM Standard Wire Termination Codes Cannon Modification Code (Not MS) The following tetmination codes are listed for your information. For lengths not shown, consult factory for proper modification code. All wire lengths are minimum. Harness TYPE (H) Solid Uninsulated Type (L) #26 AWG per MIL-W-16878/4, 7/34 strand, type E Teflon, stranded. #25 AWG gold plated copper Length All Yellow Color Coded* 3 (76.2) H020 H027 Termination Code L61 .125 (3.18) Length 6 (152.4) H019 H016 L56 .150 (3.81) 8 (203.2) H026 H034 L57 .190 (4.83) 10 (254.0) H029 H025 L39 .250 (6.35) 12 (304.8) H028 H002 L58 .375 (9.52) 18 (457.2) H001 H003 L1 .500 (12.70) 20 (508.0) H038 H023 L14 .750 (19.05) 24 (609.6) H009 H004 L2 1.000 (25.40) 30 (762.0) H010 H005 L7 1.500 (38.10) 36 (914.4) H011 H006 L6 2.000 (50.80) 48 (1219.2) H013 H048 L16 2.500 (63.50) 72 (1828.8) H017 H046 L10 3.000 (76.20) 120 (3048.0) H042 H041 Milimeters are in parentheses. * Cavity #1 black Contact Arrangements (Face View of Pin insert - Use Reverse Order for Socket Side) Standard .050 (12.70) TYP. 1 2 6 3 7 4 8 5 1 9 2 9 14 2 3 4 5 6 7 8 9 4 5 6 7 8 1 10 11 12 13 14 15 9 Contacts 1 3 2 3 4 11 12 13 15 16 17 18 19 20 21 22 23 24 25 1 17 2 3 4 5 6 7 18 19 20 21 22 23 25 Contacts 8 9 10 6 3 4 5 6 1 11 12 13 14 15 16 2 3 4 8 9 10 5 6 20 21 22 23 24 25 26 27 28 29 30 31 7 11 8 9 10 11 12 13 14 15 16 17 18 19 24 25 26 27 28 29 30 31 32 33 34 35 36 37 31 Contacts 7 9 13 14 15 16 17 18 19 20 21 37 Contacts 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 2 8 21 Contacts 1 1 7 12 15 Contacts 10 .043 (10.92) 5 46 47 48 49 50 51 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 51 Contacts 100 Contacts Contact identification numbers are for reference only and do not appear on insulator or connector body. Coaxial .714 (18.14) .460 (11.68) .320 (8.13) A1 1 2 3 A2 A1 A2 1 2 8 4 5 Size 25 Shell 5 Micro contact 2 Coax or 2 Power 3 4 5 6 7 A3 A4 9 10 11 12 13 14 15 16 17 18 19 20 Size 51 Shell 20 Micro Contacts 4 Coax or 4 Power (Not MS) .007 (0.18) Dimensions are shown in inches (millimeters). Dimensions subject to change. www.ittcannon.com 233 Micro-D Metal Shell - .050" Contact Spacing MDM Shell Dimensions (Conforms to MIL-C-83513) Plug .110 (2.79) MAX. G .186 (4.72) MAX. .284 (7.21) MAX. TWO MTG. HOLES .009 +_.003(2.31 +_0.008) B .093 (2.36) REF. F D E .200 (5.08) MAX. .416 (10.57) MAX. C A Solder Pot Receptacle .296 (7.52) MAX. TWO MTG. HOLES .009 +_.003(2.31 +_0.008) F .110 (2.79) MAX. G B .093 (2.36) REF. .429 (10.09) MAX. E D .200 (5.08) MAX. C .198 (5.03) MAX. A Solder Pot Receptacle (MDM-100 only) TWO MTG. HOLES .120 +_.003(2.31 +_0.08) G D .394 (10.01) MAX. .394 (10.01) MAX. .198 (5.03) MAX. B .093 (2.36) REF. E .296 (7.52) MAX. F Pigtail termination C A Part Number By Shell Size A Max. B Max. C Max. D Max. E Max. F + _.005 (0.13) G Max. Average Weights** oz. (gm.) + _5% MDM-9P* .785 (19.94) .334 (8.48) .400 (10.16) .270 (6.86) .308 (7.82) .565 (14.35) .185 (4.70) .063 (1.79) MDM-9S* .785 (19.94) .402 (10.21) .400 (10.16) .270 (6.86) .308 (7.82) .565 (14.35) .253 (6.43) .063 (1.79) MDM-15P* .935 (23.75) .484 (12.29) .550 (13.97) .270 (6.86) .308 (7.82) .715 (18.16) .185 (4.70) .084 (2.39) MDM-15S* .935 (23.75) .552 (13.97) .550 (13.97) .270 (6.86) .308 (7.82) .715 (18.16) .253 (6.43) .083 (2.37) MDM-21P* 1.085 (27.56) .634 (16.10) .700 (17.78) .270 (6.86) .308 (7.82) .865 (21.97) .185 (4.70) .105 (2.99) MDM-21P* 1.085 (27.56) .702 (17.83) .700 (17.78) .270 (6.86) .308 (7.82) .865 (21.97) .253 (6.43) .104 (2.97) MDM-25P* 1.185 (30.10) .734 (18.64) .800 (20.32) .270 (6.86) .308 (7.82) .965 (24.51) .185 (4.70) .119 (3.39) MDM-25S* 1.185 (30.10) .802 (20.37) .800 (20.32) .270 (6.86) .308 (7.82) .965 (24.51) .253 (6.43) .118 (3.36) MDM-31P* 1.335 (33.91) .884 (22.45) .950 (24.13) .270 (6.86) .308 (7.82) 1.115 (28.32) .185 (4.70) .140 (3.99) MDM-31S* 1.335 (33.91) .952 (24.18) .950 (24.13) .270 (6.86) .308 (7.82) 1.115 (28.32) .253 (6.43) .139 (3.96) MDM-37P* 1.485 (37.72) 1.034 (26.26) 1.100 (27.94) .270 (6.86) .308 (7.82) 1.265 (32.13) .185 (4.70) .161 (4.59) MDM-37S* 1.485 (37.72) 1.102 (27.99) 1.100 (27.94) .270 (6.86) .308 (7.82) 1.265 (32.13) .253 (6.43) .160 (4.56) MDM-51P* 1.435 (36.45) .984 (24.99) 1.050 (26.67) .310 (7.87) .351 (8.92) 1.215 (30.86) .228 (5.79) .193 (5.50) MDM-51S* 1.435 (36.45) 1.052 (26.72) 1.050 (26.67) .310 (7.87) .351 (8.92) 1.215 (30.86) .296 (7.52) .188 (5.35) MDM-100P* 2.170 (55.12) 1.384 (35.15) 1.442 (36.63) .360 (9.14) .394 (10.01) 1.800 (45.72) .271 (6.88) .500 (14.3) MDM-100S* 2.170 (55.12) 1.508 (38.10) 1.442 (36.63) .360 (9.14) .394 (10.01) 1.800 (45.72) .394 (10.01) 1.040 (29.5) *Add lead type and length; see How To Order. ***Weight given is 1/2", uninsulated, solid, #25 AWG gold plated copper pigtails. Panel Mounting Dimensions (Sizes 9 - 100) .300 +_.005 (7.62+_0.13) .200 +_.005 (5.08+_0.13) .395 +_.005 (10.03+_0.13) Plug and Receptacle Rear Mounted Plug and Receptacle Front Mounted Plug Front Mounted Receptacle Rear Mounted Dimensions are shown in inches (millimeters). Dimensions subject to change. www.ittcannon.com 234 Micro-D Metal Shell - .050" Contact Spacing MDM Panel Cutouts NOTE: See page 237 for rear panel mounting configuration. Shell Sizes 9 thru 51 C D TYP. C D TYP. .100 (2.54) R TYP. A C .450+_.002 (11.43+ _0.05) +.005 -.000 .030 (0.76) TYP. ) +0.13 -0.00 D B B FULL R. (TYP.) .015 (0.38)R. MAX.(TYP) A + + + + FULL R. (TYP.) 26/27TYP FULL R. (TYP.) Figure 1 Front Mounting PANEL REF. Figure 2 Rear Mounting Figure 3 Edgeboard Mounting Shell Size 100 1.805 .450+ _.002 .030 (11.43+ _0.05) .118 +.005 -.000 (3.00 +0.13 -0.00 1.805 +.005 -.000 (45.85 ) +0.13 -0.00 ) 1.456 +.004 -.000 (36.98 +0.10 -0.00 .015 (0.38) .361 +.004 -.000 (9.17 +0.10 -0.00 .118 +.005 -.000 (3.00 +0.13 -0.00 1.805 ) .125 +.005 -.000 (3.18 +0.13 -0.00 Figure 1 Front Mounting 1.520 +.004 -.000 (38.61 +0.10 -0.00 For 100 Shell Size NOTES: 1. Front mounting (figure 1) and rear mounting (figure 2) accommodates #4-40 screws. 2. Edgeboard mounting bracket (figure 3) uses #4-40 screws. Dimension .450+_.002 (11.43+_0.05) locates the MDM receptacle flush with the end of the board. 3. Front mounting is prefered. However, when rear mounting is necessary, use figure 2 dimensions. .401 +.004 -.000 (10.18 +0.10 -0.00 +.005 -.000 +0.13 -0.00 ) + + ) FULL R. (TYP.) Figure 2 Rear Mounting Shell Size 9 15 21 25 31 37 51 + + ) FULL R. (TYP.) ) For 9-51 Shell Sizes NOTES: 1. Front mounting (figure 1) and rear mounting (figure 2) accommodates #2-56 screws 2. Front mounting is preferred. However, when rear mounting is necessary, use figure 2 dimensions when jackscrews are used. See detail on page 24 when jackpost are used. 3. Edgeboard mounting bracket (figure 3) uses #2-56 screws. Dimension .450+_.002 (11.43+_0.05) locates the MDM receptacle flush with the end of the board. .118 (3.00 +0.13 -0.00 ) FULL R. (TYP.) +0.13 -0.00 (45.85 ) ) R. MAX (TYP.) +.005 -.000 (45.85 ) (0.76) TYP. +.005 -.000 PANEL REF. Figure 3 Edgeboard Mounting Cutout Figure A +.004 (0.10) -.000 (0.00) B +.004 (0.10) -.000 (0.00) C +.005 (0.13) -.000 (0.00) D +.005 (0.13) -.000 (0.00) 1 .408 (10.36) .271 (6.88) .570 (14.48) .089 (2.26) 2 .401 (10.19) .252 (6.40) .570 (14.48) .089 (2.26) 3 - - .570 (14.48) .089 (2.26) 1 .558 (14.17) .271 (6.88) .720 (18.29) .089 (2.26) 2 .551 (14.00) .252 (6.40) .720 (18.29) .089 (2.26) 3 - - .720 (18.29) .089 (2.26) 1 .708 (17.98) .271 (6.88) .870 (22.10) .089 (2.26) 2 .701 (17.81) .252 (6.40) .870 (22.10) .089 (2.26) 3 - - .870 (22.10) .089 (2.26) 1 .808 (20.52) .271 (6.88) .970 (24.64) .089 (2.26) 2 .801 (20.34) .252 (6.40) .970 (24.64) .089 (2.26) 3 - - .970 (24.64) .089 (2.26) 1 .958 (24.33) .271 (6.88) 1.120 (28.45) .089 (2.26) 2 .951 (24.16) .252 (6.40) 1.120 (28.45) .089 (2.26) 3 - - 1.120 (28.48) .089 (2.26) 1 1.108 (28.14) .271 (6.88) 1.270 (32.26) .089 (2.26) 2 1.101 (27.97) .252 (6.40) 1.270 (32.26) .089 (2.26) 3 - - 1.270 (32.26) .089 (2.26) 1 1.058 (26.87) .315 (8.00) 1.220 (30.99) .089 (2.26) 2 1.051 (26.70) .295 (7.49) 1.220 (30.99) .089 (2.26) 3 - 1.220 (30.99) .089 (2.26) Dimensions are shown in inches (millimeters). Dimensions subject to change. www.ittcannon.com 235 Micro-D Metal Shell - .050" Contact Spacing MDM Mouting Hardware Views (for sizes 9-51) This hardware supplied unassembled. LOCK SCREW MATING FACE #2-56 UNC-2B RETAINING CLIP .185 (4.70) MAX. CONNECTOR SHOWN FOR REF. ONLY .408 (10.36) MAX. .182 (4.62) .688 (17.48) MAX. MAX. PANEL REF. .232 (5.89) MAX. BUSHING Screw Lock Assembly .500 (12.7) MAX. #2-56 UNC-2A .093 (2.36) RECOMMENDED PANEL THICKNESS Jackpost - (P) Screw Lock Assembly* *NOTE Torque value is 2.5 in/lbs max. .052 (1.32) TYP. .096 +_ .005 (2.44 +_ 0.13)DIA. .178 +_ .005 (4.52 +_ 0.13) .170 (4.32) MAX. 90 Angle Mounting #2-56 UNC-2B THD .260 (6.60) MAX. Bracket B A 90 Angle Mounting Bracket A +_.005 (+_0.13) B Max. Description Part Number Screw Lock Assembly 322-9500-000 Jackpost kit 320-9505-000 Mounting Bracket 90 MDM 015-9516-002 .147 (3.73) .308 (7.82) 015-9516-003 .169 (4.29) .350 (8.89) N/A N/A for 9 thru 37 Shell Sizes Mounting Bracket 90 MDM fo 51 Shell Size NOTES: Screw lock assembly (322-9500-000) can be used for front mounting only. Jackpot kit (320-9505-000) consists of two assmblies, shipped unassmbled. Jackpost Bushing (for rear panel mounting-for sizes 9-51) HEX IS .135 (3.43)/.115 (2.92) ACROSS FLATS .170 (4.32) C #2-56 UNC-2B THD .185 (4.70) MATING FACE .105 (2.67) A .100 (2.54) .126 (3.20) R TYP. .125 (3.18) DIA. TYP A B 27 26 Jackpost diameter within the "A" dimension is .124/.120 (3.15/3.05). .500 (12.7) .480 (12.19) #2-56 UNC 2A THD TYP Plug and Recptacle Dimensions Shell Size A +.004 (0.10) -.000 (0.00) B +.004 (0.10) -.000 (0.00) C +_.005 (0.13) 9 .401 (10.19) .252 (6.40) .565 (14.35) 15 .551 (14.00) .252 (6.40) .715 (18.16) 21 .701 (17.81) .252 (6.40) .865 (21.97) 25 .801 (20.34) .252 (6.40) .965 (24.51) Panel A Thickness A +.005 (0.13) -.000 (0.00) Jackpost Kit Number* 3/32 (2.4) .087 (2.21) 320-9505-007 31 .951 (24.16) .252 (6.40) 1.115 (28.34) 1/16 (1.6) .056 (1.42) 320-9505-006 37 1.101 (27.97) .252 (6.40) 1.265 (32.13) 3/64 (1.2) .042 (1.07) 320-9505-005 51 1.051 (26.70) .295 (7.49) 1.215 (30.86) 1/32 (0.8) .025 (0.64) 320-9505-004 *A kit consists of 2 jackpost, 2 nuts, 2 washers. Dimensions are shown in inches (millimeters). Dimensions subject to change. www.ittcannon.com 236 Micro-D Metal Shell - .050" Contact Spacing MDM Mounting Hardware Views (sizes 9-51) This hardware is factory installed. MATING FACE .014 + _ .004 (0.36 + _ 0.10) ALLOWABLE DIAMETRAL FLOAT .020 (0.51) MAX. ALLOWABLE AXIAL FLOAT .185 (4.70) MAX .150 + _ .003 .735 (18.67) MAX. CONNECTOR SHOWN FOR REF. ONLY CONNECTOR SHOWN FOR REF ONLY HEX HEAD .050 (1.27) ACROSS FLATS .050 (1.27) DEEP (REF) .490 (12.45) MAX (3.81 + _ .076) .155 (3.94) MAX. .093 (2.36) REF. .031 + _ .003 (0.79 + _ 0.08) Float Mount - (F) #2-56 UNC-2A MATING FACE PART HAS A .040 (1.02) MAX. AXIAL FLOAT #2-56 UNC-2A MATING FACE .090 + _ .0015 (2.29 + _ 0.038)DIA PART HAS A .040 (1.02) MAX AXIAL FLOAT Jackscrew - (K) Standard Jackscrew - (L) Low Profile Shown here is a cutaway view of the float mount for the MD connector. The basic shell dimensions are the same for the float mount and the screw mounting hole configurations. Veiw shown is for standard float mount front panel mounting. Reverse mounting is available on request. * NOTE: Torque vales are as follows: Low Profile Jackscrew (L)-2.5 in/lbs Standard Jackscrew (K)-2.5 in/lbs Repair kit available-consult factory. Mounting Hardware to Military Specification (for sizes 9 - 100) per MIL-C-83513/5 This hardware supplied in kits unassembled (2 pieces of each item). #2-56 UNC-2A THREAD TYP. PLUG (REF. WITH .092 (2.34) DIA. MOUNTING HOLES #2-56 UNC-2A THREAD TYP. .062 (1.57) HEX. (REF.) .361 (9.17) MAX. .390 (9.91) MAX. SIZE 100 ONLY PLUG (REF.) WITH .092 (2.34) DIA. MOUNTING HOLES .010 (0.25) TH'K (REF.) .010 (0.25) TH'K (REF.) POTTING WELL (REF.) Figure 1. Jackscrew - Low profile Slotted Head Size 9-51 Size 100* Allen head Optional Head Configuration Plug and Receptacle Low and High Profile Size 9-51 Size 100* (same dimensions) .868 (22.05) MAX. .902 (22.91) MAX. POTTING WELL (REF.) Figure 2. Jackscrew - High Profile Slotted Head Size 9-51 Size 100* .125 (3.18) HEX. .187 (4.75) HEX. #2-56 UNC-2B THREAD #4-40 UNC -2A THREAD .190/.185(4.83/4.70) .185/.175(4.70/4.44) .475 + _ .025 (12.06 + _ 0.64) SIZE 100 SAME LOCKWASHER RETAINING NUT .154 (3.91) HEX. .187 (4.75) HEX. .062 + _ .010 (.157 + _ 0.25) SIZE 100 SAME To order hardware kits separately, order either by M83513/5-** or by 320-950X-XXX. Description Size 9-51 Mod Code Part Number ** Size 100* Mod Code Part Number ** Slotted Head Jackscrew Assy Low Profile (Figure 1) M5 320-9508-025 05 M15 320-9508-021 15 Slotted Head Jackscrew Assy Low Profile (Figure 2) M6 320-9508-027 06 M16 320-9508-023 16 Allen Head Jackscrew Assy Low Profile (Figure 1) M2 320-9508-026 02 M12 320-9508-022 12 Allen Head Jackscrew Assy High Profile (Figure 2) M3 320-9508-028 03 M13 320-9508-024 13 Jackpost Assy (Figure 3) M7 320-9505-033 07 M17 320-9505-030 17 Figure 3. Jackpost Assembly Size 9-51 Size 100* *Size 100 requires B1 size mounting holes. Dimensions are shown in inches (millimeters). Dimensions subject to change. www.ittcannon.com 237 Micro-D Metal Shell - .050" Contact Spacing MDM Mounting Hardware Views (for size 100) This hardware supplied unassembled. .123 + _ .005 (3.12 + _ 0.13) DIA. #4-40 UNC-2A $4-40 UNC-2B THD 180 (4.57 PANEL MAY BE USED WITH .093 (2.36) MAX THICK PANEL #4 LOCK WASHER +.010 -.005 +.025 -0.13 ) A .395 (10.03) MAX. .500 (12.70) MAX. .184 (4.70) MAX. MATING SIDE #4-40 UNC-2B INNER THD Jackpost - (P) 90Angle Mounting Bracket B .064 +_ .010 (1.62 + _ 0.25) TYP. .235 + _ .005 (5.97 + _ 0.13) 90 Angle Mounting Bracket Description Part Number Jackpost kit 320-9505-015 Mounting Bracket 90 MDM 015-9528-000 B Max. A +_ .005 (0.13) N/A .191 (4.85) .370 (9.40) This hardware is factory installed. .014 + _ .004 (0.36 + _ 0.10) ALLOWABLE DIAMETRAL FLOAT .020 (0.51) MAX. ALLOWABLE AXIAL FLOAT .185 (4.70) MAX MATING FACE .735 (18.64) MAX. CONNECTOR SHOWN FOR REF. ONLY .174 + _ .005 (4.4 + _ .10) HEX. SOCKET HD. .078 (1.98) ACROSS FLATS .050 (1.27 MIN. DEPTH .155 (3.94) MAX. .093 (2.36) REF. .040 (1.02) MAX. AXIAL FLOAT .116 + _ .002 (2.29 + _ .051) DIA .031 + _ .003 (0.79 + _ 0.08) MATING FACE #4-40 UNC-2A PART HAS A .040 (1.02) MAX AXIAL FLOAT #4-40 UNC-2A MATING SIDE Jackscrew - (K) Standard Float Mount - (F) Std. Jackscrew - (L) (Low Profile) *NOTE: Torque vales are as follows: Low Profile Jackscrew (L)-4.0 in/lbs Standard Jackscrew (K)-4.0 in/lbs Jackpost Bushing (for Rear Panel Mounting) ENGAGING FACE Dimensions for Rear Panel Mounting 3/16" HEX. LOCKING POST 3/16" HEX. LOCKING POST #4-40 UNC-2B 1.800 + _ .005 (45.72 + _ 0.13) .185 (4.70) .170 (4.32) Panel Thickness A +.005 (0.13) -.000 (0.00) Jackpost Kit Number* 3/32 (2.4) .087 (2.21) 320-9505-013 A .500 (12.70) MAX. 1/16 (1.6) .058 (1.42) 320-9505-012 1/32 (0.8) .025 (0.64) 320-9505-010 3/64 (1.2) .042 (1.07) 320-9505-011 #4-40 THREAD RETAINING NUT +.004 -.000 +1.10 -0.00 ) .161 (4.09) 1.516 (38.51 RECEPTACLE SHOWN FOR REF. ONLY .401 (10.18 .125 +.005 -.000 (3.18 +0.13 -0.00 ) +.004 -.000 +1.10 -0.00 .159 (4.04) DIA. ) R *2 jackposts, 2 nuts, 2 washers Dimensions are shown in inches (millimeters). Dimensions subject to change. www.ittcannon.com 238 Micro-D Metal Shell - .050" Contact Spacing MDM Connector Saver Save wear and tear on your equipment and systems connectors by using the "Connector Saver". The multi-matings and unmatings experienced by most connectors during testing and final check out can be eliminated. Simply mate the "Connectors Saver" to your unit and use the opposite side for your testing interface... less wear, less tear, less chansce of damage. It is available in all seven standard MDM layouts. Mating hardware is available and can be ordered either separately or included with the connector saver. .790 (20.07) MAX. .040 (1.02) MAX. ALLOWABLE AXIAL FLOAT #2-56 UNC-2A (TYP.) .315 (8.00) MAX. BUSHING-JACKSCREW/JACKPOST HARDWARE (OPTIONAL, FOR REFERENCE ONLY. MUST BE SPECIFIED BY CUSTOMER.) SOCKET PIN B CONN. RECEPT. A CONN., PLUG BACKPOTTING, EPOXY INTERFACIAL SEAL .185 (4.70) MAX. (TYP.) .090 (2.29) REF. (TYP.) C .900 (22.86) REF. E RING (TYP.) MDM Size 9 Shown Size A174 Electroless Nickel With Hardware W/O Hardware Cadmium Plated With Hardware W/O Hardware *Hadware Kits A Max. B + _ .005 (0.13) C Max. 9 MDM98479-86 MDM98479-18 MDM98479-78 MDM-97294-371 320-9505-014** .785 (19.94) .565 (14.35) .308 (7.82) 15 MDM98479-87 MDM98479-19 MDM98479-79 MDM-97294-372 320-9505-014** .935 (23.75) .715 (18.16) .308 (7.82) 21 MDM98479-88 MDM98479-20 MDM98479-80 MDM-97294-373 320-9505-014** 1.085 (27.56) .865 (21.97) .308 (7.82) 25 MDM98479-89 MDM98479-21 MDM98479-81 MDM-97294-374 320-9505-014** 1.185 (30.10) .965 (24.51) .308 (7.82) 31 MDM98479-90 MDM98479-14 MDM98479-82 MDM-97294-375 320-9505-014** 1.335 (33.91) 1.115 (28.32) .308 (7.82) 37 MDM98479-91 MDM98479-15 MDM98479-83 MDM-97294-376 320-9505-014** 1.485 (37.72) 1.265 (32.13) .308 (7.82) 51 MDM98479-92 MDM98479-16 MDM98479-84 MDM-97294-377 320-9505-014** 1.435 (36.45) 1.215 (30.86) .351 (8.91) 100 MDM98479-93 MDM98479-17 MDM98479-85 MDM-97294-717 320-9508-014*** 2.170 (55.12) 1.800 (45.72) .394 (10.01) * Kit contains 2 bushings-jackpost/jackscrew and 2 E rings. ** Size 9-51-#2-56 UNC2B Thread *** Size 100-#4-40 UNC2B Thread Dimensions are shown in inches (millimeters). Dimensions subject to change. www.ittcannon.com 239 Micro-D Metal Shell - .050" Contact Spacing How to Order - ITT Cannon Part Number Nomenclature to MIL-C-83513 MIL-C-83513 1 MD** 01 - H100 - ** **** ITT CANNON SERIES MDM - Metal Shell, Liquid Crystal Polymer (LCP) MDB - Diallyl Phthalate Insulator MDVB - Polyester Insulator MIL-C-83513 SLASH SHEET 01 - Plug, Connector, Solderpot 02 - Receptacle, Connector, Solderpot 03 - Plug, Connector, Crimp Type 04 - Receptacle, Connector, Crimp Type 05 - Hardware Only 7 06 07 08 09 - Plug, Connector, Solderpot Receptacle, Connector, Solderpot Plug, Connector, Crimp Type Receptacle, Connector, Crimp Type } Metal Shell } Plastic 5 INSERT ARRANGEMENT A9 B15 C21 D25 E31 F37 G51 H100 - METAL SHELL PLASTIC 9 Contact 15 Contact 21 Contact 25 Contact 31 Contact 37 Contact 51 Contact 100 Contact 9 Contact 15 Contact 21 Contact 25 Contact 31 Contact 37 Contact 51 Contact 5 WIRE TYPE NOTES: (Specify when ordering, if necessary.) 1 - For every Mil-Spec P/N, ITT has one corresponding part numbers. Example: ITT P/N's MDM01-A9 2 - Tolerance on wire lengths-18", 36" and 72" long, +1.00"/-0.00" .5" and 1.00" + .200"/-.000" 3 - For space application, connector shell finish must be "A174" and wire must be per MIL-W-22759/33-26. 4 - Any deviations to these P/N's will result in assignment of a special P/N, consult factory. 5 - No size 100 in plastic type connector. 6 - Color coding in accordance with MIL-STD-681, System 1 except the appropriate color code is the individual contact cavity number minus 1 for contact positions. 7 - For mounting hardware to Military Specification (sizes 9 to 100) see page 238. No Number - For Solderpot 01 18" long, #26 AWG per MIL-W-22759/11-26-9 02 36" long, #26 AWG per MIL-W-22759/11-26-9 03 18" long, #26 AWG per MIL-W-22759/11-26 Color Coded per MIL-STD-681, System 1 04 36" long, #26 AWG per MIL-W-22759/11-26Color Coded per MIL-STD-681, System 1 05 .5" long. #25 AWG, type S per QQ-W-343, Gold Plated 06 1.0" long, #25 AWG, type S per QQ-W-343, Gold Plated 07 .5" long, #25 AWG, type S per QQ-W-W-343, Tin Plated 08 1.0" long, #25 AWG, type S per QQ-W-343, Tin Plated 09 18" long, #26 AWG per MIL-W-22759/33-26-9 10 36" long, #26 AWG per MIL-W-22759/33-26-9 11 18" long, #26 AWG per MIL-W-22759/33-26 Color Coded per MIL-STD-681, System 1 12 36" long, #26 AWG per MIL-W-22759/33-26 Color Coded per MIL-STD-681, System 1 13 72" long, #26 AWG per MIL-W-22759/11-26-9 14 72" long, #26 AWG per MIL-W-22759/11-26 Color Coded per MIL-STD-681, System 1 15 72" long, #26 AWG per MIL-W-22759/33-26-9 16 72" long, #26 AWG per MIL-W-22759/33-26 Color Coded per MIL-STD-681, System 1 6 6 3 3 3 6 3 6 6 3 3 6 SHELL FINISH No number - for plastic type connector No number - for Cadmium A174 - Electroless Nickel 3 Qualification to slash sheets 10 thru 27 for the PCB connector will be announeced when completed. Dimensions are shown in inches (millimeters). Dimensions subject to change. www.ittcannon.com 240 Micro-D Metal Shell - .050" Contact Spacing How to Order - MIL-C-83513 Part Number Nomenclature MIL-C-83513 1 M83513/ - 01 - A ** C SERIES Connector, Electrical, Rectangular Microminiature, Polarized Shell MIL-C-83513 SLASH SHEET 01 - Plug, Connector, Solderpot 02 - Receptacle, Connector, Solderpot 03 - Plug, Connector, Crimp Type 04 - Receptacle, Connector, Crimp Type 05 - Hardware Only 7 06 07 08 09 - Plug, Connector, Solderpot Receptacle, Connector, Solderpot Plug, Connector, Crimp Type Receptacle, Connector, Crimp Type } Metal Shell } Plastic 5 INSERT ARRANGEMENT METAL SHELL A B C D E F G H - 9 Contact 15 Contact 21 Contact 25 Contact 31 Contact 37 Contact 51 Contact 100 Contact PLASTIC 9 Contact 15 Contact 21 Contact 25 Contact 31 Contact 37 Contact 51 Contact 5 WIRE TYPE NOTES: (Specify when ordering, if necessary.) 1 - For every Mil-Spec P/N, ITT has one corresponding part numbers. Example: ITT P/N's MDM01-A9 2 - Tolerance on wire lengths-18", 36" and 72" long, +1.00"/-0.00" .5" and 1.00" + .200"/-.000" 3 - For space application, connector shell finish must be "N" and wire must be per MIL-W-22759/33-26. 4 - Any deviations to these P/N's will result in assignment of a special P/N, consult factory. 5 - No size 100 in plastic type connector. 6 - Color coding in accordance with MIL-STD-681, System 1 except the appropriate color code is the individual contact cavity number minus 1 for contact positions. 7 - For mounting hardware to Military Specification (sizes 9 to 100) see page 238. No Number - For Solderpot 01 18" long, #26 AWG per MIL-W-22759/11-26-9 02 36" long, #26 AWG per MIL-W-22759/11-26-9 03 18" long, #26 AWG per MIL-W-22759/11-26 Color Coded per MIL-STD-681, System 1 04 36" long, #26 AWG per MIL-W-22759/11-26Color Coded per MIL-STD-681, System 1 05 .5" long. #25 AWG, type S per QQ-W-343, Gold Plated 06 1.0" long, #25 AWG, type S per QQ-W-343, Gold Plated 07 .5" long, #25 AWG, type S per QQ-W-W-343, Tin Plated 08 1.0" long, #25 AWG, type S per QQ-W-343, Tin Plated 09 18" long, #26 AWG per MIL-W-22759/33-26-9 10 36" long, #26 AWG per MIL-W-22759/33-26-9 11 18" long, #26 AWG per MIL-W-22759/33-26 Color Coded per MIL-STD-681, System 1 12 36" long, #26 AWG per MIL-W-22759/33-26 Color Coded per MIL-STD-681, System 1 13 72" long, #26 AWG per MIL-W-22759/11-26-9 14 72" long, #26 AWG per MIL-W-22759/11-26 Color Coded per MIL-STD-681, System 1 15 72" long, #26 AWG per MIL-W-22759/33-26-9 16 72" long, #26 AWG per MIL-W-22759/33-26 Color Coded per MIL-STD-681, System 1 6 6 3 3 3 6 3 6 6 3 3 6 SHELL FINISH No letter - for plastic type connector C - Cadmium N - Electroless Nickel 3 Qualification to slash sheets 10 thru 27 for the PCB connectors will be announced when completed. Dimensions are shown in inches (millimeters). Dimensions subject to change. www.ittcannon.com 241 Micro-D PCB - .050" Contact Spacing MDM-PCB connectors are designed for use with flex circuitry, flat cable and printed circuit boards or multi-layer boards. They use the standard MDM metal shell and provide high density and high reliability in board-to-board, board-to-cable and cable-to-cable applications. MDM-PCB MDM-PCB connectors are available in 8 shell sizes with 9 to 100 contacts. Terminations may be straight (BS) or at 90u (BR, CBR) board thickness. Jackpost mounting for use with locking hardware is also available. How to Order - MDM-PCB Series MDM * - 25 P BS P - T L39 A174 SERIES INSULATOR MATERIAL CONTACT ARRANGEMENT CONTACT TYPE TERMINATION TYPE MOUNTING HARDWARE (Shell Flange) MOUNTING HARDWARE FOR PCB TERMINATION TAIL LENGTH MODIFICATION CODE SHELL FINISH MODIFICATION CODES SERIES MDM - Microm "D" Metal Shell INSULATOR MATERIAL Liquid Crystal Polymer (LCP) CONTACT ARRANGEMENT 9, 15, 21, 25, 31, 37, 51, and 100 Size 100 not available in "BR" CONTACT TYPE P - Pin (Plug) S - Socket (Receptacle) TERMINATION TYPE BS - Straight PCB Termination BR - 90u PCB Termination CBR - 90u Narrow Profile PCB Terminations MOUNTING HARDWARE (Shell Flange) P - Jackposts M7 - Jackposts M83513/5-07 (Sizes 9-51) M17 - Jackposts M83513/5-17 (Size 100) No letter - none MOUNTING HARDWARE FOR PCB T - Threaded Insert #2-56 Thd for Shell Sizes 9 thru 51 #4-40 Thd for Shell Size 100 No letter - none TERMINATION TAIL LENGTH MODIFICATION CODE None - .109 (2.77) +_.015 (0.38) Standard L61 - .125 (3.18) L56 - .150 (3.81) L57 - .190 (4.83) L39 - .250 (6.35) L58 - .375 (9.52) SHELL FINISH MODIFICATION CODES None - Yellow Chromate/Cadmium over Nickel A174 - Electroless Nickel A172 - Gold over Nickel A141 - Irridite/Alodine A30 - Black Anodize (For special modification codes, consult factory.) NOTE: Back molding material - Epoxy Hysol #MG40FS Dimensions are shown in inches (millimeters). Dimensions subject to change. www.ittcannon.com 242 Micro-D PCB - .050" Contact Spacing MDM-PCB BS (Board Straight) Series A B D C .186 (4.72) MAX. PLUG .198 (5.03) MAX. RECEPTACLE F E G K J CAV. #1 .096 + _ .005 (2.44 + _ 0.13) DIA. Size 9-51) H LAST CAV. JACKPOST (9-51) #2-56 UNC-2B TYP. .109 + _ 0.15 (2.77 + _ 0.38) JACKPOST (100) #4-40 UNC-2B TYP. .120 + _ .005 (3.05 + _ 0.13) Size 100 LAST CAV. * .100 (2.54) REF. CAV. #1 PCB Termination Arrangements* (Viewed from PCB solder side) Identification number shown for plug connector, use reverse order for socket connector. .050 (1.27) 6 1 7 2 8 3 .050 (1.27) 9 4 NOTE: Dimensions shown are for reference only-consult factory for final design dimensions. 5 1 2 3 .375 (9.53) 4 5 6 7 .050 (1.27) .050 (1.27) 9 10 11 12 13 14 15 12 13 8 1 2 14 15 16 17 18 19 20 21 3 5 6 7 8 9 10 11 15 Contacts 2 3 4 5 6 7 8 9 10 20 21 22 23 24 25 26 27 28 29 30 31 11 12 13 14 15 16 1 .150 (3.81) 2 3 4 5 6 7 8 9 10 .050 (1.27) 32 33 34 35 36 37 .100 (2.54) TYP. 77 27 1 78 53 28 2 75 54 29 3 5 6 7 8 9 10 11 12 13 36 37 38 39 40 41 42 43 44 45 46 47 48 19 11 12 13 14 15 16 17 18 19 1 37 Contacts 52 4 49 50 51 35 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 .150 (3.81) 31 Contacts 76 3 25 Contacts .050 (1.27) 1 2 21 Contacts 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 .150 (3.81) 1 .150 (3.81) .225 (5.72) .225 (5.72) TYP. 9 Contacts 4 14 15 16 17 18 19 20 21 22 23 24 25 80 55 30 4 81 56 31 5 82 57 32 6 83 58 33 7 84 59 34 8 85 60 35 9 86 36 10 87 61 62 37 11 12 88 89 63 38 64 39 13 51 Contacts 90 65 40 14 91 66 41 15 92 67 42 16 93 43 17 94 68 69 44 18 .150 (3.81) 19 95 70 45 96 71 46 20 21 97 72 47 98 73 48 22 99 100 74 49 23 75 50 24 25 51 26 .150 (3.81) 100 Contacts NOTE: Standard lead termination is #24 AWG, solid copper, solder or tin dipped All Termination Configurations .100 (2.54) x .100 (2.54) Grid Pattern, Offset .050 (1.27) Part Number By Shell Size MDM-9PBS* A Max. 1.390 (35.31) B + _.007 (.018) 1.150 (29.21) C + _.005 (.013) .565 (14.35) D Max. .785 (19.94) E Max. .334 (8.48) F Max. .185 (4.70) G Max. .308 (7.82) H Max. .165 (4.19) J Max. .355 (9.02) K Max. .555 (14.10) MDM-9SBS* 1.390 (35.31) 1.150 (29.21) .565 (14.35) .785 (19.94) .402 (10.21) .253 (6.43) .308 (7.82) .165 (4.19) .355 (9.02) .555 (14.10) MDM-15PBS* 1.390 (35.31) 1.150 (29.21) .715 (18.16) .935 (23.75) .484 (12.29) .185 (4.70) .308 (7.82) .165 (4.19) .355 (9.02) .555 (14.10) MDM-15SBS* 1.390 (35.31) 1.150 (29.21) .715 (18.16) .935 (23.75) .552 (13.97) .253 (6.43) .308 (7.82) .165 (4.19) .355 (9.02) .555 (14.10) MDM-21PBS* 1.690 (43.93) 1.450 (36.83) .865 (21.97) 1.085 (27.56) .634 (16.10) .185 (4.70) .308 (7.82) .165 (4.19) .355 (9.02) .555 (14.10) MDM-21SBS* 1.690 (43.93) 1.450 (36.83) .865 (21.97) 1.085 (27.56) .702 (17.83) .253 (6.43) .308 (7.82) .165 (4.19) .355 (9.02) .555 (14.10) MDM-25PBS 1.740 (44.20) 1.500 (38.10) .965 (24.51) 1.185 (30.10) .734 (18.64) .185 (4.70) .308 (7.82) .165 (4.19) .355 (9.02) .555 (14.10) MDM-25SBS* 1.740 (44.20) 1.500 (38.10) .965 (24.51) 1.185 (30.10) .802 (20.37) .253 (6.43) .308 (7.82) .165 (4.19) .355 (9.02) .555 (14.10) MDM-31PBS* 2.040 (51.82) 1.800 (45.72) 1.115 (28.32) 1.335 (33.91) .884 (22.45) .185 (4.70) .308 (7.82) .165 (4.19) .355 (9.02) .555 (14.10) MDM-31SBS* 2.040 (51.82) 1.800 (45.72) 1.115 (28.32) 1.335 (33.91) .952 (24.18) .253 (6.43) .308 (7.82) .165 (4.19) .355 (9.02) .555 (14.10) MDM-37PBS* 2.340 (59.44) 2.100 (53.34) 1.265 (32.13) 1.485 (37.72) 1.034 (26.26) .185 (4.70) .308 (7.82) .165 (4.19) .355 (9.02) .555 (14.10) MDM-37SBS* 2.340 (59.44) 2.100 (53.34) 1.265 (32.13) 1.485 (37.72) 1.102 (27.99) .253 (6.43) .308 (7.82) .165 (4.19) .355 (9.02) .555 (14.10) MDM-51PBS* 2.270 (67.66) 2.000 (50.80) 1.215 (30.86) 1.435 (36.45) .984 (24.99) .228 (5.79) .351 (8.92) .165 (4.19) .355 (9.02) .555 (14.10) MDM-51SBS* 2.270 (67.66) 2.000 (50.80) 1.215 (30.86) 1.435 (36.45) 1.052 (26.72) .296 (7.52) .351 (8.92) .165 (4.19) .355 (9.02) .555 (14.10) MDM-100PBS* 3.070 (77.98) 2.800 (71.12) 1.800 (45.72) 2.175 (55.24) 1.384 (35.15) .271 (6.88) .460 (11.68) .303 (7.70) .550 (12.70) .686 (17.42) MDM-100SBS* 3.070 (77.98) 2.800 (71.12) 1.800 (45.72) 2.175 (55.24) 1.508 (38.30) .394 (10.01) .460 (11.68) .303 (7.70) .550 (12.70) .686 (17.75) *For jackpost, add letter "P" or "M7" for sizes 9-51, "M17" for size 100. Dimensions are shown in inches (millimeters). Dimensions subject to change. www.ittcannon.com 243 Micro-D PCB - .050" Contact Spacing MDM-PCB BR (Board Right Angle) Series C .109 + _ .015 (2.77 + _ 0.38) E CAV. #1 JACKPOST #2-56 UNC-2B TYP. .186 (4.72) MAX. PLUG .198 (5.05) MAX. A G B .125 + _ .015 (3.18 + _ 0.38) D .100 (2.54) TYP. F LAST CAV. .050 (1.27) TYP. .096 + _ .005 (2.44 + _ 0.31) .150 + _ .010 (3.8 + _ 0.25) .100 TYP. PCB Termination Arrangements (Viewed from bottom of connector, PCB solder side.) Identification number shown for plug connector, use reverse order for socket connector. .150 (3.81) 6 7 1 2 8 3 9 4 9 10 11 12 13 14 15 5 1 2 3 4 5 6 7 12 13 .300 (7.62) 8 .375 (9.53) .150 (3.81) .150 (3.81) .150 (3.81) 1 2 14 15 16 17 18 19 20 21 22 23 24 25 14 15 16 17 18 19 20 21 3 4 5 6 7 8 1 9 10 11 15 Contacts 9 Contacts 4 5 5 6 7 8 9 10 11 12 13 .175 (4.45) 25 Contacts .050 (1.27) 20 21 22 23 24 25 26 27 28 29 30 31 36 32 33 34 35 36 37 19 3 4 .150 (3.81) 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 2 3 21 Contacts .150 (3.81) 1 2 .225 (5.72) 6 7 8 9 10 11 12 13 14 15 16 1 2 3 4 5 6 7 8 9 10 1 11 12 13 14 15 16 17 18 19 .150 (3.81) NOTE: Standard lead termination is #24 AWG, gold plated, solid copper, solder or tin dripped. 2 3 4 5 6 7 8 9 10 49 50 51 34 35 11 12 13 14 15 16 17 18 .150 (3.81) .150 (3.81) 51 Contacts 37 Contacts 31 Contacts 37 38 39 40 41 42 43 44 45 46 47 48 20 21 22 23 24 25 26 27 28 29 30 31 32 33 All Termination Configurations .100 (2.54) x .100 (2.54) Grid Pattern, Offset .050 (1.27). Part Number By Shell Size A Max. B + _ .007 (.018) C + _ .005 (.013) D Max. E Max. F Max. G Max. MDM-9PBR* 1.390 (35.31) 1.150 (29.21) .565 (14.35) .334 (8.48) .185 (4.70) .455 (11.56) .308 (7.82) MDM-9SBR* 1.390 (35.31) 1.150 (29.21) .565 (14.35) .402 (10.21) .253 (6.43) .455 (11.56) .308 (7.82) MDM-15PBR* 1.540 (39.12) 1.300 (33.02) .715 (18.16) .484 (12.29) .185 (4.70) .455 (11.56) .308 (7.82) MDM-15SBR* 1.540 (39.12) 1.300 (33.02) .715 (18.16) .552 (13.97) .253 (6.43) .455 (11.56) .308 (7.82) MDM-21PBR* 1.690 (42.93) 1.450 (36.83) .865 (21.97) .634 (16.10) .185 (4.70) .455 (11.56) .308 (7.82) MDM-21SBR* 1.690 (42.93) 1.450 (36.83) .865 (21.97) .702 (17.83) .253 (6.43) .455 (11.56) .308 (7.82) MDM-25PBR* 1.790 (45.47) 1.550 (39.37) .965 (24.51) .734 (18.64) .185 (4.70) .455 (11.56) .308 (7.82) MDM-25SBR* 1.790 (45.47) 1.550 (39.37) .965 (24.51) .802 (20.37) .253 (6.43) .455 (11.56) .308 (7.82) MDM-31PBR* 2.040 (51.82) 1.800 (45.72) 1.115 (28.32) .884 (22.45) .185 (4.70) .455 (11.56) .308 (7.82) MDM-31SBR* 2.040 (51.52) 1.800 (45.72) 1.115 (28.32) .952 (24.18) .253 (6.43) .455 (11.56) .308 (7.82) MDM-37PBR* 2.340 (59.44) 2.100 (53.34) 1.265 (32.13) 1.034 (26.26) .185 (4.70) .455 (11.56) .308 (7.82) MDM-37SBR* 2.340 (59.44) 2.100 (53.34) 1.265 (32.13) 1.102 (27.99) .253 (6.43) .455 (11.56) .308 (7.82) MDM-51PBR* 1.875 (47.63) 1.600 (40.64) 1.215 (30.86) .984 (24.99) .228 (5.79) .565 (14.35) .351 (8.92) MDM-51SBR* 1.875 (47.63) 1.600 (40.64) 1.215 (30.86) 1.052 (26.72) .296 (7.52) .565 (14.35) .351 (8.92) *For jackpost, add letter "P" or "M7" for sizes 9-51, "M17" for size 100. Dimensions are shown in inches (millimeters). Dimensions subject to change. www.ittcannon.com 244 Micro-D PCB - .050" Contact Spacing MDM-PCB CBR (Condensed Board Right Angle) Series LAST CAV. JACKPOST 2-56 UNC-2B TYP. (Size 9-51) A C .109 + _ .015 (2.77 + _ 0.38) + D + .186 (4.72) MAX.PLUG .198 (5.03) MAX. RECEPT. CAV. #1 B JACKPOST #4-40 UNC 2B TYP. .185 (4.70)MAX. H G F E C H H G G F .096 + _ .005 (2.44 + _ 0.31) DIA.TYP. (Size 9-51) SEE VIEW X SEE VIEW Y F .125 + _ .005 (3.18 + _ 0.31) DIA. TYP. ** * * FOR 31: 1.085(27.56) MAX. FOR 37: 1.185(30.10) MAX. FOR 51: 1.225(31.12) MAX. 1.815 (46.10) MAX. SEE VIEW W 100 VIEW PCB Termination Arrangements (Viewed from bottom of connector, PCB solder side.) Identification number shown for plug connector, use reverse order for socket connector. .108 (2.73) .083 (2.11) 5 4 9 2 8 .100 (2.54) TYP. 7 3 .020 (0.51) 1 7 8 15 5 6 14 4 12 13 3 11 1 10 .083 (2.11) .020 (0.51) 2 10 21 6 9 11 9 20 .083 (2.11) 6 8 7 19 5 4 17 18 3 16 1 14 15 .020 (0.51) 13 10 11 12 2 13 24 25 8 5 7 21 20 23 19 12 .020 (0.51) 15 Contacts View X 25 Contacts View X 21 Contacts View X .325 (8.26) .183 (4.65) .158 (4.00) 16 13 14 30 .020 (0.51) 12 29 31 11 28 27 9 10 25 26 8 24 6 7 23 4 5 21 22 2 3 19 20 19 1 17 18 17 37 18 .020 (0.51) 16 35 36 34 15 13 14 33 12 31 32 30 11 10 29 7 9 5 8 28 27 6 26 25 3 4 24 23 22 15 17 1 18 2 35 20 16 34 21 51 50 13 14 33 32 49 27 11 12 31 28 30 48 47 8 43 45 44 6 7 9 10 29 46 42 26 40 4 5 25 41 39 2 3 24 38 25 1 23 22 37 31 Contacts View Y 37 Contacts View Y .050 (1.27) 20 36 C Max. MDM-9PCBR* .785 (19.94) .565 (14.35) .334 (8.48) MDM-9SCBR* .785 (19.94) .565 (14.35) .402 (10.21) MDM-15PCBR* .935 (23.75) .715 (18.16) MDM-15SCBR* .935 (23.75) MDM-21PCBR* 20 49 50 75 47 48 73 74 100 99 72 97 70 68 94 92 95 93 13 14 41 42 69 67 96 15 16 43 46 44 71 98 17 18 45 .275 (6.98) 40 65 66 91 38 88 89 8 10 62 86 87 59 60 85 57 58 84 3 82 83 1 4 33 36 34 61 5 6 37 35 63 64 90 7 9 11 12 39 2 31 32 29 27 30 55 56 80 81 28 53 54 52 78 79 76 .100 + _ .005 (2.54 +_ 0.13) 77 100 Contacts View W NOTE: Standard lead termination is #24 AWG, solid copper, solder or tin dripped. All Termination Configurations .100 (2.54) x .100 (2.54) Grid Pattern, Offset .050 (1.27). B + _ .005 (.013) 21 19 22 51 51 Contacts View Y A Max. 23 24 26 21 19 .108 (2.73) Part Number By Shell Size 14 16 18 1 15 17 .050 (1.27) TYP. 9 Contacts View X 15 2 3 4 6 9 22 D Max. E Max. F Max. G + _ .010 (.025) H + _ .010 (.025) .308 (7.82) .185 (4.70) .308 (7.82) .253 (6.43) .420 (10.67) .250 (6.35) .230 (5.81) .420 (10.67) .250 (6.35) .484 (12.29) .308 (7.82) .230 (5.81) .185 (4.70) .420 (10.67) .250 (6.35) .715 (18.16) .552 (13.97) .130 (3.30) .308 (7.82) .253 (6.43) .420 (10.67) .250 (6.35) 1.085 (27.56) .865 (21.97) .130 (3.30) .634 (16.10) .308 (7.82) .185 (4.70) .420 (10.67) .250 (6.35) MDM-21SCBR* 1.085 (27.56) .130 (3.30) .865 (21.97) .702 (17.83) .308 (7.82) .253 (6.43) .420 (10.67) .250 (6.35) MDM-25PCBR* .130 (3.30) 1.185 (30.10) .965 (24.51) .734 (18.64) .308 (7.82) .184 (4.70) .420 (10.67) .250 (6.35) .130 (3.30) MDM-25SCBR* 1.185 (30.10) .965 (24.51) .802 (20.37) .308 (7.82) .253 (6.43) .420 (10.67) .250 (6.35) .130 (3.30) MDM-31PCBR* 1.335 (33.91) 1.115 (28.32) .884 (22.45) .308 (7.82) .185 (4.70) .520 (13.21) .250 (6.35) .130 (3.30) MDM-31SCBR* 1.335 (33.91) 1.115 (28.32) .952 (24.18) .308 (7.82) .253 (6.43) .520 (13.21) .250 (6.35) .130 (3.30) MDM-37PCBR* 1.485 (37.72) 1.265 (32.13) 1.034 (26.26) .308 (7.82) .185 (4.70) .520 (13.21) .250 (6.35) .130 (3.30) MDM-37SCBR* 1.485 (37.72) 1.265 (32.13) 1.102 (27.99) .308 (7.82) .253 (6.43) .520 (13.21) .250 (6.35) .130 (3.30) MDM-51PCBR* 1.435 (36.45) 1.215 (30.86) .984 (24.99) .351 (8.92) .228 (5.79) .650 (16.15) .300 (7.62) .150 (3.81) MDM-51SCBR* 1.435 (36.45) 1.215 (30.86) 1.052 (26.72) .351 (8.92) .296 (7.52) .650 (16.15) .300 (7.62) .150 (3.81) MDM-100PCBR* 2.170 (55.12) 1.800 (45.72) 1.384 (35.15) .394 (10.01) .271 (6.88) 1.000 (25.40) .400 (10.16) .200 (5.08) MDM-100SCBR* 2.170 (55.12) 1.800 (45.72) 1.508 (38.10) .394 (10.01) .394 (10.01) 1.000 (25.40) .400 (10.16) .200 (5.08) *For jackpost, add letter "P" or "M7" for sizes 9-51, "M17" for size 100. Dimensions are shown in inches (millimeters). Dimensions subject to change. www.ittcannon.com 245 Micro-D Coaxial/Power - .050" Contact Spacing MDM C/P MDM Coaxial MDM Power The MDM Metal Shell Connectors have been tooled in The same insulator that is used with coaxial contacts is several coaxial layouts and offer the versatility of combin- available with power contacts. This offers the versatility ing coaxial and signal lines in the same connector. Any of combining power and signal lines in the same connec- modifications to these layouts or new requirements, tor. please consult the factory. For ordering information see page 232. For contact layouts see page 233. Standard MDM Coaxial/Power coax is RG178 white. Power and coaxial contacts can be interchanged as desired. Power contacts are rated at 13 amps, 24V rms, AWG #16 stranded. 7C2/7P2 .186 (4.92) MAX. 1.185 (30.10) MAX. 308 (7.82) MAX .965 + _ .005 (24.51 + _ 0.13) .416 (10.57) MAX. + .199 (5.05) MAX. 1.185 (30.10) MAX. .965 + _ .005 (24.51 + _ 0.13) .308 (7.82) MAX. + .100 (2.54) MAX. .091 + _ .003 DIA. (2.31 + _ 0.08) .800 (20.32) MAX. + + .429 (10.90) MAX. .100 (2.54) MAX. .091 + _ .003 DIA. (2.31 + _ 0.08) Plug .800 (20.32) MAX. Receptacle 24C4/24P4 .186 (4.92) MAX. 1.435 (36.45) MAX. .351 (8.92) MAX. + .091 + _ .003 DIA. (2.31 + _ 0.08) .199 (5.05) MAX. 1.435 (36.45) MAX. 1.215 + _ .005 (30.86 + _ 0.13) 1.215 + _ .005 (30.86 + _ 0.13) .351 (8.92) MAX. + .416 (10.51) MAX. .100 (2.54) MAX. 1.050 (26.67) MAX. + + .091 + _ .003 DIA. (2.31 + _ 0.08) Plug .429 (10.90) MAX. .100 (2.54) MAX. Receptacle 1.050 (26.67) MAX. Coaxial Contacts Plug Receptacle Power Contacts BACK POTTING REQUIRED .350 (8.89) MAX. Receptacle Plug Dimensions are shown in inches (millimeters). Dimensions subject to change. www.ittcannon.com 246 Miro-D Plastic Shell - .050" Contact Spacing Microminiature Rectangular Connectors with MICRO- ITT Cannon can also terminate a wide variety of stranded or solid wire directly to MICRO-D contacts, which is often Pin Contacts on .050 (1.27) centers. MICRO-D microminature rack/panel connectors are used in applications requiring highly reliable, extremely small, MD** * Glass-filled diallyl phthalate-a thermoset material used in high termperature applications that is immune to desirable in high density arrangements. cleaning solvents. It also has excellent dielectric prop- MICRO-D connectors can also be custom harnessed to erties. meet any customer requirement of single or multiple (--55C to +149C). lightweight connectors. connectors. Pigtail lead and harness description must be These connectors are available in 2 insulator materials, 2 given by the customer. A typical description would be: .5" mounting variations, 7 shell sizes accommodating from 9 #25 AWG, gold plated copper leads or 18" of #26 to 51 contacts and a special arrangement of 5 micro yellow, Teflon-insulated, Type E wire. Shown below are contacts and 2 coaxials. The insulator materials listed give various methods of termination. Consult the factory for the MICRO-D connector wide versatility in most applica- any routine or complex harnessing of MICRO-D connec- tions required by industry. tors. Temperature * Glass-filled range: polyester-a- -65F thermoplastic to +300F that is not affected by cleaning solvents and exhibits excellent dielectric properties. Temperature range: -55F to +257F (-65C to +125C). How to Order PCB ordering information - page 242 MD** 1- 9 P H 001 P SERIES-INSULATOR STYLE-MATERIAL CONTACT SPACING CONTACT ARRANGEMENT CONTACT TYPE TERMINATION TYPE TERMINATION CODE LOCKING HARDWARE SERIES-INSULATOR STYLE-MATERIAL TERMINATION TYPE LOCKING HARDWARE (SCREW MOUNTING ONLY) P - Jackpost MD - Clip mounting -Diallyl phthalate H - Insulated solid or stranded wire MDB - Screw mounting-Diallyl phthalate L - Uninsulated solid wire K - Jackscrew-standard MDV - Clip mounting-Polyester S - Solder pot to accept #26 AWG max. L - Jackscrew-low profile MDVB - Screw mounting-Polyester CONTACT SPACING 1 - .050 (1.27) centers harness wire. 237. (H) 001 - 18", 7/34 strand, #26 AWG, No designator - No hardware - standard mounting MIL-W-16878/4, Type E Teflon, Yel- .091 (2.31) hole diameter low. (H) 003 - 18", 7/34 strand, #26 AWG, CONTACT TYPE MIL-W-16878/4, Type E Teflon, color P - Pin S - Socket M - Military specification hardware, see page TERMINATION CODE** CONTACT ARRANGEMENT 9-15-21-25-31*-37-51. See page 233. F - Float mount coded to MIL-STD-681 System I. (L) 1 - 1/2" uninsulated solid #25 AWG gold plated copper. (L) 2 - 1" uninsulated solid #25 AWG gold plated copper. * Not available in clip mounting. ** See table below for additional codes. Standard Wire Termination Codes For lengths not shown, consult factory for proper modification code. All wire lengths are minimum. Harness Type (H) #26 AWG per MIL-W-16878 Type E Teflon, stranded. Length Solid Uninsulated Type (L) #25 AWG Gold Plated Copper All Yellow Color Coded* 3 (76.2) H020 H027 Termination Code L61 .125 (3.18) Length 6 (152.4) H019 H016 L56 .150 (3.81) 8 (203.2) H026 H034 L57 .190 (4.83) 10 (254.0) H029 H025 L39 .250 (6.35) 12 (304.8) H028 H002 L58 .375 (9.52) 18 (457.2) H001 H003 L1 .500 (12.70) 20 (508.0) H038 H023 L14 .750 (19.05) 24 (609.6) H009 H004 L2 1.000 (25.40) 30 (762.0) H010 H005 L7 1.500 (38.10) 36 (914.4) H011 H006 L6 2.000 (50.80) 48 (1219.2) H013 H048 L16 2.500 (63.50) 72 (1828.8) H017 H046 L10 3.000 (76.20) 120 (3048.0) H042 H041 * Cavity #1 black Dimensions are shown in inches (millimeters). Dimensions subject to change. www.ittcannon.com 247