Ordering number : ENN6045 SPS-445 Series SPS-445 Series Receiver Pre-amp Module for Infrared Remote Control Features * This is an unified module consisting of a PIN photodiode and receiver pre-amp IC. It is a compact type, not necessary to mount outer part, and provides low voltage and low power consumption. * It also puts a measure to inverter fluorescent lamp with a high frequency trap circuit for band-pass filter. Absolute Maximum Ratings at Ta=25C (as per JIS C 7032) Parameter Symbol VCC PD Topr Tstg Tsol Line Voltage Power Dissipation Operating Temperature Storage Temperature Soldering Temperature Rating 0 to +6.3 100 --10 to +60 --20 to +70 +260 *1 Unit V mW C C C Recommended Operating Condition at Ta=25C Parameter Symbol Opr. Condition Unit Line Voltage VCC +4.7 to +5.3 V We recommend the signal format with leader code (for example ; NEC format or Home Electrical Appliances Society format in Japan) for the remote control transmitter. Electrical / Optical Characteristics at Ta=25C, VCC=5.0V D.C. Parameter Consumption Current Symbol ICC Controlling Distance L Low-level Output Voltage High-level Output Voltage VL VH Low-level Pulse Width TWL High-level Pulse Width TWH Carrier Wave Frequency fo *1 Condition Non-signal input *2 On axis *2 form device Cone with its limit inclined at 30 deg to axis Cone with its limit inclined at 40 deg to axis 2 * At the point of 30cm on axis *2 At the point of 30cm on axis *2 Specified by TWL time interval of output at the point of 30cm and 7.5m on axis *2 Specified by TWH time interval of output at the point of 30cm and 7.5m on axis -- Min. -7.5 Typ. 1.4 10.0 Max. 2.2 -- Unit mA m 5.0 -- -- m 3.0 -4.5 ---- -0.5 -- m V V 300 610 900 s 300 590 900 s -- *3 -- kHz Soldering time : with in 3sec and clearance of 1mm from lead stopper. *2 As shown in Fig.1, burst wave shall be transmitted by our transmitter in item 7. *3 Detector face illuminance : Ee < 10 lx Carrier wave frequency (fo) differs every a type. Refer to the following list. SANYO Electric Co.,Ltd. Semiconductor Company TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN D2099 GI, (MI) No.6045 1/5 SPS-445 Series Type No. SPS-445-E SPS-445-1-E SPS-445-2-E SPS-445-3-E SPS-445-4-E SPS-445-6-E Carrier wave frequency (fo) 40 kHz 38 kHz 36.7 kHz 33.3 kHz 36 kHz 56.8 kHz Precautions of Use Precautions (1) Care must be taken to avoid bending leads. (2) Do not apply any force or mechanical stress onto the leads or plastic part during soldering. (3) Confirm reliability in terms of devices, because it sometimes acts be wrong by the ingredient of the ripple noise of the power supply lines. Please design the ripple voltage of the power supply line below 1mVp-p. Please attach the RC filter (R=100, C=22F) for the power supply lines. Pulse Waveform fo kHz Leader pulse Burst wavefom of transmitter 9ms 4.5ms 600s 600s 50% Output waveform 50% TWH TWL Fig.1 Pulse waveform 600s TWL Transmitter The Transmitter shall be defined by adjusting the output of transmitter to make Vo=400mVp-p according to the burst wave shown in Fig. 1 and measurement condition shown in Fig.2. In addition infrared LED used in the transmitter is set to peak=945nm, =45nm, and photodiode used in the receiver is set to 32nA / Ix (VR=5.0V). 20cm 10k 100k -- Oscilloscorpe Output 10k + Transmitter 10F 12 0.1V GND Fig.2 The output adjustment of transmitter No.6045 2/5 SPS-445 Series Measurement Condition DUT Transmitter L DUT : Device Under Test Controlling distance Fig.3 Measurement Condition Block Diagram VCC Waveform Amp. Shaper Limiter Detector BPF + TRAP ABLC RL Vout GND Fig.4 Block Diagram Note 1. Vout : Active "Low" output 2. RL.=15k to 51k . 3. The power supply filter is not being attached. No.6045 3/5 SPS-445 Series SPS-445 Series Package Dimensions and Pinconnection (3.8) 6.9 1.65 Photo diode chip 18.5 6.65 10 o5.4 (4.1) 2.95 0.5 3 1.5 1.2 1.4 2.7 0.4 3.6 0.5 0.8 0.5 *1 2.54 *1 2.54 2.54 2.54 5-o 0.8 3 (Pu nch hole ) < Recommended mounting drawing from soldering side > * * * 1 4 * * * 2 3 5 1 GND 2 Vout 3 VCC (4 GND) (5 GND) Tolerance : 0.3 Unit : mm Note 1) *1 indicates root dimensions of leads. 2) Pin4, Pin5 has been connected Pin1 (GND) in a product. 3) The width and position of the leads of "*" marke may be changed. No.6045 4/5 SPS-445 Series CAUTION 1. No products described or contained herein are intended for use in surgical implants, life-support systems, aerospace equipment, nuclear power control systems, vehicles, disaster / crime-prevention equipment or the like, and the failure of which may directly or indirectly cause injury, death or property loss. 2. Anyone purchasing any products described or contained herein for an above-mentioned use shall: 1) Accept full responsibility and indemnify and defend SANYO ELECTRIC CO.,LTD., it's affiliates, subsidiaries and distributors or any of their officers and employees, jointly and severally, against any and all claims and litigation and all damages, costs and expenses associated with such use. 2) Not impose any responsibility for any fault or negligence which may be cited in any such claim or litigation on SANYO ELECTRIC CO., LTD., it's affiliates, subsidiaries and distributors or any of their officers and employees jointly or severally. 3. Information (including circuit diagrams and circuit parameters) disclosed herein is for example only; it is not guaranteed for mass production, SANYO believes the information disclosed herein is accurate and reliable, but no guarantees are made or implied regarding it's use or any infringements of intellectual property rights or other rights of third parties. Precautionary instructions in handling gallium arsenic products Special precautions must be taken in handling this product because it contains, gallium arsenic, which is designated as a toxic substance by law. Be sure to adhere strictly to all applicable laws and regulations enacted for this substance, particularly when it comes to disposal. Manufactured by ; Tottori SANYO Electric Co., Ltd. LED Division 5-318, Tachikawa-cho, Tottori City, 680-8634 Japan TEL: +81-857-21-2137 FAX: +81-857-21-2161 PS No.6045 5/5