EVALUATION KIT AVAILABLE HART Modem DS8500 General Description Benefits and Features The DS8500 is a single-chip modem with Highway Addressable Remote Transducer (HART) capabilities. It has been fully tested and verified and has received a HART(R) Certificate of Registration. The device integrates the modulation and demodulation of the 1200Hz/2200Hz FSK signal, has very low power consumption, and needs only a few external components due to the integrated digital signal processing. The input signal is sampled by an analog-to-digital converter (ADC), followed by a digital filter/demodulator. This architecture ensures reliable signal detection in noisy environments. The output digital-to-analog converter (DAC) generates a sine wave and provides a clean signal with phasecontinuous switching between 1200Hz and 2200Hz. Low power is achieved by disabling the receive circuits during transmit and vice versa. The DS8500 is ideal for low-power process control transmitters. * Single-Chip, Half-Duplex Modem Overlays 1200bps Applications 4mA-20mA Loop-Powered Transmitters for Temperature, Pressure, Flow, and Level Measurement HART Multiplexers HART Modem Interface Connectivity * * * * FSK Digital Communication on Top of Installed 4mA-20mA Current Loop Infrastructure Digital Signal Processing Provides Reliable Input Signal Detection in Noisy Conditions Standard Component 3.6864MHz Crystal Reduces System Cost Fully Tested and Verified as a HART-Registered Modem IC Integrated Solution Requires Minimal Power and Space * 2.7V to 3.6V Operating Voltage * 285A (max) Current Consumption * Space-Saving, 5mm x 5mm x 0.8mm, 20-Pin TQFN Package * Few External Components Required Ordering Information PART TEMP RANGE PIN-PACKAGE DS8500-JND+ -40C to +85C 20 TQFN-EP* +Denotes a lead(Pb)-free/RoHS-compliant package. *EP = Exposed pad. FSK_IN REF FSK_OUT AVDD TOP VIEW AGND Pin Configuration 15 14 13 12 11 DGND 16 10 XCEN MODE 17 9 DGND 8 XTAL2 7 XTAL1 6 RTS DGND 18 DS8500 D_OUT 19 *EXPOSED PAD. 19-7581; Rev 2; 4/15 2 3 4 5 RST OCD DVDD 1 DGND HART is a registered trademark of the HART Communication Foundation. Membership in the HART Communication Foundation does not guarantee a product has been verified or received a HART Registration Certificate. *EP + DVDD D_IN 20 THIN QFN (5mm x 5mm) HART Modem DS8500 Absolute Maximum Ratings Voltage Range on All Pins (including AVDD, DVDD) Relative to Ground .................................-0.5V to +3.6V Voltage Range on Any Pin Relative to Ground Except AVDD, DVDD .............-0.5V to (VDVDD + 0.5V) Operating Temperature Range ...........................-40C to +85C Storage Temperature Range .............................-65C to +150C Soldering Temperature...........................Refer to the IPC/JEDEC J-STD-020 Specification. Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Recommended DC Operating Conditions (VDVDD = VAVDD = 2.7V to 3.6V, TA = -40C to +85C.) (Note 1) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS Digital Supply Voltage VDVDD 2.7 3.6 V Analog Supply Voltage VAVDD VAVDD = VDVDD 2.7 3.6 V Ground GND AGND = DGND 0 0 V Digital Power-Fail Reset Voltage VRST Monitors VDVDD 2.59 2.69 V 285 A DGND 0.30 x VDVDD V 0.75 x VDVDD VDVDD V I OL = 4mA DGND 0.4 V VOH I OH = -4mA 0.8 x VDVDD CIO Guaranteed by design (Note 3) Active Current IDD Input Low Voltage VIL Input High Voltage VIL Output Low Voltage VOL Output High Voltage I/O Pin Capacitance 2.64 VAVDD = VDVDD = 2.7V (Note 2) V 15 pF RST Pullup Resistance RRST 19 45 k Input Leakage Current XTAL, RST I ILRX -30 +30 A Input Leakage Current All Other Pins I IL -2 +2 A Input Low Current for RST I IL1 170 A +1% MHz VIN = 0.4V CLOCK SOURCE External Clock Frequency fHFIN -1% 3.6864 VOLTAGE REFERENCE Internal Reference Voltage VREF 1.23 V FSK INPUT Input Voltage Range at FSK_IN 0 VREF V 600 mVP-P FSK OUTPUT Output Voltage at FSK_OUT Frequency of FSK_OUT (Note 4) Note 1: Note 2: Note 3: Note 4: VOUT AC-coupled max 30k load 400 500 For a mark -1% 1200 +1% For a space -1% 2200 +1% Hz Specifications to -40C are guaranteed by design and are not production tested. Active currents are measured when the device is driven by an external clock XCEN = 1 condition. Guaranteed by design and not production tested. Accuracy is guaranteed based on the external crystal or clock provided. www.maximintegrated.com Maxim Integrated | 2 HART Modem DS8500 Pin Description PIN NAME FUNCTION 1, 2 DVDD Digital Supply Voltage 3, 9, 16, 18 DGND Digital Ground 4 RST Active-Low Reset, Digital Input/Output. This pin includes an internal pullup resistor and is driven low as an output when an internal reset condition occurs. 5 OCD Carrier Detect, Digital Output. A logic-high indicates a valid carrier detection on FSK_IN. OCD = 1 when FSK_IN amplitude is greater than 120mVP-P. OCD = 0 when FSK_IN amplitude is less than 80mVP-P. 6 RTS Request to Send, Digital Input. When set high, the device is put into the demodulator mode. A logic-low puts the device into modulator mode. 7 XTAL1 Crystal Pin or Input for External Clock at 3.6864MHz 8 XTAL2 Crystal Pin or Output of the Crystal Amplifier 10 XCEN External Clock Enable, Digital Input. When set high, this pin allows the user to drive an external clock signal through XTAL1. When in this mode, XTAL2 should be left unconnected. An external crystal must be connected between XTAL1 and XTAL2 when set low. 11 AVDD Analog Supply Voltage 12 FSK_OUT 13 REF 14 FSK_IN 15 AGND Analog Ground 17 MODE This pin should be tied high for HART applications. This pin can also be tied low for support of legacy designs. 19 D_OUT 20 D_IN -- EP FSK Out, Analog Output. Output of the modulator. Provides a phase-continuous, FSK-modulated output signal (1200Hz and 2200Hz output frequencies) to the 4-20mA current loop interface circuit. Reference, Analog Output. The internal voltage reference is provided as output. This pin must be connected to a 0.1F capacitor. FSK In, Analog Input. Input for the FSK-modulated HART receive signal from the 4-20mA current loop interface circuit. Digital Data Out, Digital Output. Output from the demodulator. Digital Data In, Digital Input. Input to the modulator. Exposed Pad. Should be connected to ground (DGND, AGND). Block Diagram XTAL1 XTAL2 CRYSTAL OSCILLATOR RST DVDD DGND CLOCK GENERATOR POWER MONITOR AGND AVDD VREF 1.23V REF XCEN OCD MODE Rx DEMODULATOR DIGITAL FILTER SAMPLE/HOLD ADC FSK_IN D_OUT RTS D_IN www.maximintegrated.com Tx MODULATOR DAC FSK_OUT DS8500 Maxim Integrated | 3 HART Modem DS8500 Introduction to HART Modulator HART is a backward-compatible enhancement to existing 4-20mA instrumentation networks that allows twoway, half-duplex, digital communication with a microcontroller-based field device. The digital signal is encoded on top of the existing instrumentation signal. Communication is accomplished through a series of commands and responses dependent on the specific protocol and network topology. The DS8500 does not implement any portion of the communication protocol; it only handles the modulation and demodulation of the encoded information. Digital data is encoded using frequency-shift keying (FSK), which is illustrated in Figure 1. A "1" is identified as a mark symbol and is represented with a center frequency of 1.2kHz. A "0" is identified as a space symbol and is represented with a center frequency of 2.2kHz. This allows a throughput of 1.2kbps, with each symbol occupying an 833s slot. The modulator performs the FSK modulation of the digital data at the D_IN input. The FSK-modulated sinusoidal signal is present at the FSK_OUT output as illustrated in Figure 1. The modulator is enabled by RTS being a logic-low. The modulation is done between 1200Hz (mark) or 2200Hz (space) depending on the logic level of the input signal. The modulator preserves a continuous phase when switching between frequencies to minimize the bandwidth of the transmitted signal. Figure 2 illustrates an example waveform of the DS8500 in modulate mode. The data to be modulated is presented in a UART format (start, 8 data bits, parity, stop bit) at D_IN. FSK_OUT shows the modulated output. V Demodulator The demodulator accepts an FSK signal at the FSK_IN input and reproduces the original modulating signal at the D_OUT output. The HART signal should be presented as an 11-bit UART character with a start, data, parity, and stop bits for proper operation of the demodulator block. The nominal bit rate of the D_OUT signal is 1200 bits per second. A simple RC filter is sufficient for anti-aliasing. Figure 3 illustrates an example waveform of the DS8500 in demodulate mode. Applications Information T 1.2kHz MARK "1" 2.2kHz SPACE "0" Figure 1. HART FSK Signal Figure 4 shows the typical application circuit. As the DS8500 integrates a digital filter, only a simple passive RC filter is required in front of the ADC. R3 and C3 implement a lowpass filter with a 10kHz cutoff frequency; C2 and R2/R1 implement a highpass filter with a 480Hz cutoff frequency. The resistor-divider formed by R1 and R2 provides an input bias voltage of VREF/2 to the ADC input (R1 = R2). The output DAC provides a sine-wave signal, and C4 provides the AC-coupled signal output from the DS8500. The typical value of C4 can be anything greater than 20nF based on the application. Functional Description HART Registration The DS8500 modem chip consists of a demodulator, carrier detect, digital filter, ADC for input signal conversion, a modulator and DAC for output signal generation, and receive and transmit state machine blocks to perform the HART communication. The Block Diagram illustrates the interface between various blocks of circuitry. The input HART signal's noise interference is attenuated by a one-pole highpass filter that is external to the chip; the attenuated signal is digitized by the ADC and filtered by the receive state machine. The transmit state machine modulates the input to the HART-compliant signal with the help of the modulator and the DAC. This IC has been tested and has received a Modem IC Registration Certificate from the HART Communication Foundation. The use of this HART-registered IC reduces the customer cost and effort associated with achieving HART registration of the end product. www.maximintegrated.com A copy of the DS8500 Registration Certificate (L2-061000-346) is available from the HART Communication Foundation at www.hartcomm.org. Technical Support For technical support, go to http://support.maximintegrated.com/micro. Maxim Integrated | 4 HART Modem DS8500 1200bps/833s D_IN STOP START 8-BIT DATA PARITY FSK_OUT Figure 2. Actual DS8500 Modulator Waveform FSK_IN START 8-BIT DATA STOP PARITY D_OUT 1200bps/833s ONE UART CHARACTER (START, 8 DATA BITS, PARITY, STOP) Figure 3. Actual DS8500 Demodulator Waveform www.maximintegrated.com Maxim Integrated | 5 HART Modem DS8500 POWER SUPPLY 2.7V TO 3.6V 3.6864MHz RST MODE DVDD DGND AGND AVDD XTAL1 3.6864MHz CRYSTAL XTAL2 27pF CRYSTAL OSCILLATOR CLOCK GENERATOR POWER MONITOR VREF 1.23V REF 27pF R1 C1 XCEN OCD D_OUT Rx DEMODULATOR DIGITAL FILTER SAMPLE/HOLD ADC C2 FSK_IN R3 HART IN R2 C3 DS8500 RTS D_IN C4 Tx MODULATOR DAC HART AND 4-20mA OUT FSK_OUT MICROCONTROLLER 4-20mA DAC OUTPUT Figure 4. Typical Application Circuit Package Information For the latest package outline information and land patterns (footprints), go to www.maximintegrated.com/packages. Note that a "+", "#", or "-" in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status. PACKAGE TYPE PACKAGE CODE OUTLINE NO. LAND PATTERN NO. 20 TQFN T2055+3 21-0140 90-0008 www.maximintegrated.com Maxim Integrated | 6 HART Modem DS8500 Revision History REVISION NUMBER REVISION DATE 0 10/08 Initial release. -- 2/09 In the Electrical Characteristics table, changed the Frequency of FSK_OUT parameter units from kHz to Hz. 2 1 Added the EP description to the Pin Description table. 3 2 4/15 PAGES CHANGED DESCRIPTION Updated Benefits and Features section, added HART registration information, clarified alternate function of pin 17 1, 3, 4, 6 For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim Integrated's website at www.maximintegrated.com. Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance. Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc. (c) 2015 Maxim Integrated Products, Inc. | 7 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Maxim Integrated: DS8500-JND+ DS8500-JND+T&R