155 Mbps bi-directional SC Receptacle single Fiber Transceiver B-1X/1X-155(C)-F-SSC3 Features * Diplexer Single Mode Single Fiber 2x5 SFF SC Receptacle connector * Wavelength Tx 1310nm/Rx 1530 nm (B-13/15-155(C)-F-SSC3X) * Wavelength Tx 1530nm/Rx 1310 nm(B-15/13-155(C)-F-SSC3X) * SONET OC-3 SDH STM-1 Compliant * Single +3.3V Power Supply * LVPECL Differential Inputs and Outputs (B-1x/1x-155-F-SSC3X) * LVTTL Differential Inputs and Outputs (B-1x/1x-155C-F-SSC3X) * Wave Solderable and Aqueous Washable * Class 1 Laser Int. Safety Standard IEC-825 Compliant * Uncooled Laser diode with MQW structure * Complies with Telcordia (Bellcore) GR-468-CORE * EMI Shielding Finger Optional * RoHS compliance available Absolute Maximum Rating Parameter Symbol Min. Max. Unit Vcc 0 3.6 V - 0 Vcc V Power Supply Voltage Input Voltage Output Current Note Iout - 30 mA Soldering Temperature - - 260 C Operating Temperature Topr 0 70 C B-1X/1X-155-F-SSC3(S) Operating Temperature Topr -40 85 C B-1X/1X-155-F-SSC3A(S) Storage Temperature Tstg -40 85 C 10 seconds on leads only Recommended Operating Condition Parameter Symbol Min. Typ. Max. Power Supply Voltage Vcc 3.1 3.3 3.5 V Operating Temperature Topr 0 - 70 C - - 155 - Mbps Data Rate Unit Transmitter Specifications Parameter Optical Symbol Min Typical Max Unit Notes Optical Transmit Power Po -14 - -8 dBm Output Power is coupled into a 9/125 m single mode fiber Output center Wavelength 1260 1310 1360 nm B-13/15-155-F-SSC3X Output center Wavelength 1480 1530 1580 nm B-15/13-155-F-SSC3X RMS() Output Spectrum Width - - 3 nm Extinction Ratio ER 8.2 - - dB Output Eye Compliant with ITU recommendation G.957/STM-1 Optical Rise Time tr - - 2 ns 10% to 90% Values Optical Fall Time tf - - 2 ns 10% to 90% Values 30 - - dB Tx: 1310nm / Rx: 1550 nm RIN - - -116 dB/Hz TJ - - 1.0 ns Optical Isolation Relative Intensity Noise Total Jitter LUMINENTOIC.COM Measured with 223-1 PRBS with 72 ones and 72 zeros. 20550 Nordhoff St. * Chatsworth, CA 91311 * tel: 818.773.9044 * fax: 818.576.9486 9F, No 81, Shui Lee Rd. * Hsinchu, Taiwan, R.O.C. * tel: 886.3.5169222 * fax: 886.3.5169213 1 LUMNDS597-Sep1206 Rev A.5 155 Mbps bi-directional SC Receptacle single Fiber Transceiver B-1X/1X-155(C)-F-SSC3 Transmitter Specifications Parameter Electrical Symbol Min Typical Max Unit Supply Current ICC - - 140 mA Data Input Current-Low IIL -350 - - A Data Input Current-High IIH - - 350 A Differential Input Voltage Notes Maximum current is specified at Vcc= Maximum @ maximum temperature VIH-VIL 300 - - mV Transmitter Disable Voltage VDIS 2 - Vcc V LVTTL input, Tx Disable pin 8 Transmitter Enable Voltage VEN 0 - 0.8 V Tx enabled when open circuit Data Input Voltage-Low VIL-VCC -2.0 - -1.58 V Data Input Voltage-High VIH-VCC -1.1 - -0.74 V These inputs are compatible with 10K, 10KH and 100K ECL and PECL inputs Symbol Min Typical Max Unit Notes - - - -33 dBm Maximum Input Power Pin -3 - - dBm Signal Detect-Asserted Pa - - -33 dBm Measured on transition: low to high (Note 1) Signal Detect-Deasserted Pd -45 - - dBm Measured on transition: high to low (Note 1) Signal Detect-Hysteresis - 1 - 4 dB Cross Talk - - - -33 dB Wavelength of Operation - 1480 - 1600 nm B-13/15-155-F-SSC3X 1260 - 1360 nm B-15/13-155-F-SSC3X Receiver Specifications Parameter Optical Sensitivity Wavelength of Operation Measured with 223-1 PRBS,BER= 10-10 Note 1: The SD level should be deasserted when fiber disconnected Receiver Specifications Parameter Electrical Symbol Min Typical Max Unit Note Supply Current ICC - - 100 mA The current excludes the output load current Data Output Voltage-Low VOL -Vcc -2.0 - -1.58 V Data Output Voltage-High VOH- Vcc -1.1 - -0.74 V VSDL-Vcc Signal Detect Output Voltage-High VSDH- Vcc Signal Detect Output Voltage-Low VSDL-Vcc -2.0 - -1.58 V -1.1 - -0.74 V - - 0.5 V Signal Detect Output Voltage-High VSDH- Vcc 2.0 - - V Signal Detect Output Voltage-Low LUMINENTOIC.COM These outputs are compatible with 10K, 10KH and 100KECL and PECL outputs LVPECL, B-1x/1x-155-F-SLC3(A) LVTTL, B-1x/1x-155C-F-SLC3(A) 20550 Nordhoff St. * Chatsworth, CA 91311 * tel: 818.773.9044 * fax: 818.576.9486 9F, No 81, Shui Lee Rd. * Hsinchu, Taiwan, R.O.C. * tel: 886.3.5169222 * fax: 886.3.5169213 2 LUMNDS597-Sep1206 Rev A.5 155 Mbps bi-directional SC Receptacle single Fiber Transceiver B-1X/1X-155(C)-F-SSC3 Connection Diagram PIN Symbol 1 RxGND Notes Directly connect this pin to the receiver ground plane 2 RxVcc +3.3V dc power for the receiver section 3 SD Active high on this indicates a received optical signal(LVPECL/LVTTL) 4 RD- Receiver Data Out Bar(LVPECL) 5 RD+ Receiver Data Out (LVPECL) 6 TxVcc 7 TxGND +3.3V dc power for the transmitter section Directly connect this pin to the tranmitter ground plane 8 Warnings TxDIS 9 TD+ Transmitter Data In (LVPECL) 10 TD- Transmitter Data In Bar (LVPECL) LUMINENTOIC.COM Transmitter disable(LVTTL) 20550 Nordhoff St. * Chatsworth, CA 91311 * tel: 818.773.9044 * fax: 818.576.9486 9F, No 81, Shui Lee Rd. * Hsinchu, Taiwan, R.O.C. * tel: 886.3.5169222 * fax: 886.3.5169213 3 LUMNDS597-Sep1206 Rev A.5 155 Mbps bi-directional SC Receptacle single Fiber Transceiver B-1X/1X-155(C)-F-SSC3 Recommended Circuit Schematic B-1X/1X-155-F-SSC3(A) PHY DEVICE TERMINATE AT TRANSCEIVER INPUTS Vcc(+3.3V) Z=50 TD- LVPECL 100 Z=50 TD+ 130 1 2 3 TxGND TxVcc RD- RD+ 6 TxDIS 7 Tx Disable SD TD+ RxVcc Rx 8 TD- Tx 9 RxGND 10 4 130 1H Vcc(+3.3V) C2 C3 10F Vcc(+3.3V) 1H C1 5 LVTTL RD+ Z=50 LVPECL 100 RD- Z=50 130 Vcc(+3.3V) 130 Z=50 130 SD LVPECL 82 NOTE:C1=C2=C3=100nF TERMINATE AT DEVICE INPUTS The split-loaded terminations for ECL signals need to be located at the input of devices receiving those ECL signals. The power supply filtering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module Rx Vcc. A GND plane under the module is required for good EMI and sensitivity performance. LUMINENTOIC.COM 20550 Nordhoff St. * Chatsworth, CA 91311 * tel: 818.773.9044 * fax: 818.576.9486 9F, No 81, Shui Lee Rd. * Hsinchu, Taiwan, R.O.C. * tel: 886.3.5169222 * fax: 886.3.5169213 4 LUMNDS597-Sep1206 Rev A.5 155 Mbps bi-directional SC Receptacle single Fiber Transceiver B-1X/1X-155(C)-F-SSC3 Recommended Circuit Schematic B-1X/1X-155C-F-SSC3(A) PHY DEVICE TERMINATE AT TRANSCEIVER INPUTS Vcc(+3.3V) Z=50 TD- LVPECL 100 Z=50 TD+ 130 1 2 3 TxGND TxVcc RD- RD+ 6 TxDIS 7 Tx Disable SD TD+ RxVcc Rx 8 TD- Tx 9 RxGND 10 4 130 1H Vcc(+3.3V) C2 C3 10F Vcc(+3.3V) 1H C1 5 LVTTL RD+ Z=50 LVPECL 100 RD- Z=50 130 Vcc(+3.3V) 130 Z=50 SD LVTTL NOTE:C1=C2=C3=100nF TERMINATE AT DEVICE INPUTS The split-loaded terminations for ECL signals need to be located at the input of devices receiving those ECL signals. The power supply filtering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module Rx Vcc. A GND plane under the module is required for good EMI and sensitivity performance. LUMINENTOIC.COM 20550 Nordhoff St. * Chatsworth, CA 91311 * tel: 818.773.9044 * fax: 818.576.9486 9F, No 81, Shui Lee Rd. * Hsinchu, Taiwan, R.O.C. * tel: 886.3.5169222 * fax: 886.3.5169213 5 LUMNDS597-Sep1206 Rev A.5 155 Mbps bi-directional SC Receptacle single Fiber Transceiver B-1X/1X-155(C)-F-SSC3 Recommended Circuit Board Layout DIMENSION IN MILLIMETER (INCHES) NOTES: 1.THIS FIGURE DESCRIBE THE RECOMMAND CIRCUIT BOARD LAYOUT FOR THE SFF TRANSCEIVER. 2.THE HATCHED AREAS ARE KEEP-OUT AREAS RESERVED FOR HOUSING STANDOFF. NO METAL TRACES OR GROUND CONNECTION IN KEEP-OUT AREAS. 3.THE MOUNTING STUDS SHOULD BE SOLDERED TO CHASSIS GROUND FOR MECHANICAL INTEGRITY. LUMINENTOIC.COM 20550 Nordhoff St. * Chatsworth, CA 91311 * tel: 818.773.9044 * fax: 818.576.9486 9F, No 81, Shui Lee Rd. * Hsinchu, Taiwan, R.O.C. * tel: 886.3.5169222 * fax: 886.3.5169213 6 LUMNDS597-Sep1206 Rev A.5 155 Mbps bi-directional SC Receptacle single Fiber Transceiver B-1X/1X-155(C)-F-SSC3 Package Diagram Units: mm B-1X/1X-155(C)-F-SSC3(A) Warnings Housing Lead PIN 1 PIN 5 Stand-off Legal Notice Housing Lead Stud Stand-off LUMINENTOIC.COM PIN 10 PIN 6 Stand-off 20550 Nordhoff St. * Chatsworth, CA 91311 * tel: 818.773.9044 * fax: 818.576.9486 9F, No 81, Shui Lee Rd. * Hsinchu, Taiwan, R.O.C. * tel: 886.3.5169222 * fax: 886.3.5169213 7 LUMNDS597-Sep1206 Rev A.5 155 Mbps bi-directional SC Receptacle single Fiber Transceiver B-1X/1X-155(C)-F-SSC3 Package Diagram Units: mm B-1X/1X-155(C)-F-SSC3S B-1X/1X-155(C)-F-SSC3AS Matel Finger Stand-off PIN 1 PIN 5 Stand-off Housing Lead Stud PIN 10 PIN 6 Stand-off Housing Lead LUMINENTOIC.COM 20550 Nordhoff St. * Chatsworth, CA 91311 * tel: 818.773.9044 * fax: 818.576.9486 9F, No 81, Shui Lee Rd. * Hsinchu, Taiwan, R.O.C. * tel: 886.3.5169222 * fax: 886.3.5169213 8 LUMNDS597-Sep1206 Rev A.5 155 Mbps bi-directional SC Receptacle single Fiber Transceiver B-1X/1X-155(C)-F-SSC3 Ordering Information Available Options: B-13/15-155-F-SSC3 B-15/13-155-F-SSC3 B-13/15-155-F-SSC3A B-15/13-155-F-SSC3A B-13/15-155-F-SSC3S B-15/13-155-F-SSC3S B-13/15-155-F-SSC3AS B-15/13-155-F-SSC3AS B-13/15-155-F-SSC3-G5 B-15/13-155-F-SSC3-G5 B-13/15-155-F-SSC3A-G5 B-15/13-155-F-SSC3A-G5 B-13/15-155-F-SSC3S-G5 B-15/13-155-F-SSC3S-G5 B-13/15-155-F-SSC3AS-G5 B-15/13-155-F-SSC3AS-G5 B-13/15-155C-F-SSC3 B-15/13-155C-F-SSC3 B-13/15-155C-F-SSC3A B-15/13-155C-F-SSC3A B-13/15-155C-F-SSC3S B-15/13-155C-F-SSC3S B-13/15-155C-F-SSC3AS B-15/13-155C-F-SSC3AS B-13/15-155C-F-SSC3-G5 B-15/13-155C-F-SSC3-G5 B-13/15-155C-F-SSC3A-G5 B-15/13-155C-F-SSC3A-G5 B-13/15-155C-F-SSC3S-G5 B-15/13-155C-F-SSC3S-G5 B-13/15-155C-F-SSC3AS-G5 B-15/13-155C-F-SSC3AS-G5 Part numbering Definition: B - 1X/1X - 155(C) - F - S SC 3 Operating Temperature Shielding Finger -RoHS * Wavelength 13/15: Tx Wavelength=1310nm Rx Wavelength=1530nm 15/13: Tx Wavelength=1530nm Rx Wavelength=1310nm * Communication protocol 155= LVPECL SD output 155C= LVTTL SD output * +3.3 V SFF Transceiver * Single mode fiber * Connector options * Intermediate Reach * Operating Temperature Blank = Commercial temperature (0 to 70) A = Commercial temperature (-40 to 85) * Shielding Finger Option Blank = No shielding finger S = with Shielding finger * Ordering Information Blank = RoHS non-compliant product G5 = RoHS 5/6-compliant product (lead exemption) LUMINENTOIC.COM 20550 Nordhoff St. * Chatsworth, CA 91311 * tel: 818.773.9044 * fax: 818.576.9486 9F, No 81, Shui Lee Rd. * Hsinchu, Taiwan, R.O.C. * tel: 886.3.5169222 * fax: 886.3.5169213 9 LUMNDS597-Sep1206 Rev A.5 155 Mbps bi-directional SC Receptacle single Fiber Transceiver B-1X/1X-155(C)-F-SSC3 Warnings: Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow guidelines according to proper ESD procedures. Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation. Legal Notes: IMPORTANT NOTICE! All information contained in this document is subject to change without notice, at LuminentOIC's sole and absolute discretion. LuminentOIC warrants performance of its products to current specifications only in accordance with the company's standard one-year warranty; however, specifications designated as "preliminary" are given to describe components only, and LuminentOIC expressly disclaims any and all warranties for said products, including express, implied, and statutory warranties, warranties of merchantability, fitness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company's Terms and Conditions of Sale for further warranty information. LuminentOIC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual property described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and LuminentOIC makes no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. Products described in this document are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. LuminentOIC customers using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify LuminentOIC for any damages resulting from such use or sale. THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN "AS IS" BASIS. Customer agrees that LuminentOIC is not liable for any actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact LuminentOIC to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current. (c) LuminentOIC, Inc. 2003 All rights reserved LUMINENTOIC.COM 20550 Nordhoff St. * Chatsworth, CA 91311 * tel: 818.773.9044 * fax: 818.576.9486 9F, No 81, Shui Lee Rd. * Hsinchu, Taiwan, R.O.C. * tel: 886.3.5169222 * fax: 886.3.5169213 10 LUMNDS597-Sep1206 Rev A.5