B-13/15-155C-F-SSC3SG5 - Source Photonics, Inc.

155 Mbps bi-directional SC Receptacle

single Fiber Transceiver

B-1X/1X-155(C)-F-SSC3

20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486

9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213

LUMINENTOIC.COM LUMNDS597-Sep1206

Rev A.5

Parameter Symbol Min Typical Max Unit Notes

Optical

Optical Transmit Power Po-14 - -8 dBm Output Power is coupled into a 9/125 µm

single mode ﬁber

Output center Wavelength λ1260 1310 1360 nm B-13/15-155-F-SSC3X

Output center Wavelength λ1480 1530 1580 nm B-15/13-155-F-SSC3X

Output Spectrum Width ∆λ- - 3 nm RMS(σ)

Extinction Ratio ER 8.2 - - dB

Output Eye Compliant with ITU recommendation G.957/STM-1

Optical Rise Time tr- - 2 ns 10% to 90% Values

Optical Fall Time tf- - 2 ns 10% to 90% Values

Optical Isolation 30 - - dB Tx: 1310nm / Rx: 1550 nm

Relative Intensity Noise RIN - - -116 dB/Hz

Total Jitter TJ - - 1.0 ns Measured with 223-1 PRBS with 72 ones and

72 zeros.

Transmitter Speciﬁcations

Features

• Diplexer Single Mode Single Fiber 2x5 SFF SC Receptacle

connector

• Wavelength Tx 1310nm/Rx 1530 nm (B-13/15-155(C)-F-SSC3X)

• Wavelength Tx 1530nm/Rx 1310 nm(B-15/13-155(C)-F-SSC3X)

• SONET OC-3 SDH STM-1 Compliant

• Single +3.3V Power Supply

• LVPECL Differential Inputs and Outputs

(B-1x/1x-155-F-SSC3X)

• LVTTL Differential Inputs and Outputs

(B-1x/1x-155C-F-SSC3X)

• Wave Solderable and Aqueous Washable

• Class 1 Laser Int. Safety Standard IEC-825 Compliant

• Uncooled Laser diode with MQW structure

• Complies with Telcordia (Bellcore) GR-468-CORE

• EMI Shielding Finger Optional

• RoHS compliance available

Parameter Symbol Min. Max. Unit Note

Power Supply Voltage Vcc 0 3.6 V

Input Voltage -0 Vcc V

Output Current Iout - 30 mA

Soldering Temperature -- 260 ºC 10 seconds on leads only

Operating Temperature Topr 0 70 ºC B-1X/1X-155-F-SSC3(S)

Operating Temperature Topr -40 85 ºC B-1X/1X-155-F-SSC3A(S)

Storage Temperature Tstg -40 85 ºC

Absolute Maximum Rating

Parameter Symbol Min. Typ. Max. Unit

Power Supply Voltage Vcc 3.1 3.3 3.5 V

Operating Temperature Topr 0 - 70 ºC

Data Rate - - 155 - Mbps

Recommended Operating Condition

155 Mbps bi-directional SC Receptacle

single Fiber Transceiver

B-1X/1X-155(C)-F-SSC3

20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486

9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213

LUMINENTOIC.COM LUMNDS597-Sep1206

Rev A.5

Parameter Symbol Min Typical Max Unit Note

Electrical

Supply Current ICC - - 100 mA The current excludes the output load current

Data Output Voltage-Low VOL -Vcc -2.0 - -1.58 V

These outputs are compatible with 10K,

10KH and 100KECL and PECL outputs

Data Output Voltage-High VOH- Vcc -1.1 - -0.74 V

Signal Detect Output Voltage-Low VSDL-Vcc -2.0 - -1.58 V LVPECL, B-1x/1x-155-F-SLC3(A)

Signal Detect Output Voltage-High VSDH- Vcc -1.1 - -0.74 V

Signal Detect Output Voltage-Low VSDL-Vcc - - 0.5 V LVTTL, B-1x/1x-155C-F-SLC3(A)

Signal Detect Output Voltage-High VSDH- Vcc 2.0 - - V

Receiver Speciﬁcations

Parameter Symbol Min Typical Max Unit Notes

Electrical

Supply Current ICC - - 140 mA Maximum current is speciﬁed at Vcc=

Maximum @ maximum temperature

Data Input Current-Low IIL -350 - - µA

Data Input Current-High IIH - - 350 µA

Differential Input Voltage VIH-VIL 300 - - mV

Transmitter Disable Voltage VDIS 2 - Vcc V LVTTL input, Tx Disable pin 8

Tx enabled when open circuit

Transmitter Enable Voltage VEN 0 - 0.8 V

Data Input Voltage-Low VIL-VCC -2.0 - -1.58 V These inputs are compatible with 10K, 10KH

and 100K ECL and PECL inputs

Data Input Voltage-High VIH-VCC -1.1 - -0.74 V

Transmitter Speciﬁcations

Parameter Symbol Min Typical Max Unit Notes

Optical

Sensitivity - - - -33 dBm Measured with 223-1 PRBS,BER= 10-10

Maximum Input Power Pin -3 - - dBm

Signal Detect-Asserted Pa - - -33 dBm Measured on transition: low to high (Note 1)

Signal Detect-Deasserted Pd -45 - - dBm Measured on transition: high to low (Note 1)

Signal Detect-Hysteresis - 1 - 4 dB

Cross Talk - - - -33 dB

Wavelength of Operation - 1480 - 1600 nm B-13/15-155-F-SSC3X

Wavelength of Operation 1260 - 1360 nm B-15/13-155-F-SSC3X

Note 1: The SD level should be deasserted when ﬁber disconnected

Receiver Speciﬁcations

155 Mbps bi-directional SC Receptacle

single Fiber Transceiver

B-1X/1X-155(C)-F-SSC3

20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486

9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213

LUMINENTOIC.COM LUMNDS597-Sep1206

Rev A.5

Warnings

Connection Diagram

PIN Symbol Notes

1RxGND Directly connect this pin to the receiver ground plane

2 RxVcc +3.3V dc power for the receiver section

3 SD Active high on this indicates a received optical signal(LVPECL/LVTTL)

4 RD- Receiver Data Out Bar(LVPECL)

5 RD+ Receiver Data Out (LVPECL)

6 TxVcc +3.3V dc power for the transmitter section

7 TxGND Directly connect this pin to the tranmitter ground plane

8 TxDIS Transmitter disable(LVTTL)

9 TD+ Transmitter Data In (LVPECL)

10 TD- Transmitter Data In Bar (LVPECL)

155 Mbps bi-directional SC Receptacle

single Fiber Transceiver

B-1X/1X-155(C)-F-SSC3

20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486

9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213

LUMINENTOIC.COM LUMNDS597-Sep1206

Rev A.5

Recommended Circuit Schematic

The split-loaded terminations for ECL signals need to be located at the input of devices receiving those ECL signals.

The power supply ﬁltering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module Rx Vcc.

A GND plane under the module is required for good EMI and sensitivity performance.

TERMINATE AT

TRANSCEIVER INPUTS Z=50�

Z=50

100

TD-

TD+

130

82

Vcc(+3.3V)

100

RD+

RD-

Z=50�

Z=50

130130

Vcc(+3.3V)

PHY DEVICE

LVPECL

10F

C3C2

1H

67810 9

1 2 3 4 5

1H

TERMINATE AT

DEVICE INPUTS

NOTE:C1=C2=C3=100nF

RxGND

RxVcc

RD-

RD+ TxVcc

TxGND

TD+

TD-

TxDIS

Vcc(+3.3V)

130

LVTTL

Tx Disable

LVPECL

B-1X/1X-155-F-SSC3(A)

155 Mbps bi-directional SC Receptacle

single Fiber Transceiver

B-1X/1X-155(C)-F-SSC3

20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486

9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213

LUMINENTOIC.COM LUMNDS597-Sep1206

Rev A.5

Recommended Circuit Schematic

The split-loaded terminations for ECL signals need to be located at the input of devices receiving those ECL signals.

The power supply ﬁltering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module Rx Vcc.

A GND plane under the module is required for good EMI and sensitivity performance.

TERMINATE AT

TRANSCEIVER INPUTS Z=50�

Z=50

100

TD-

TD+

130

Vcc(+3.3V)

100

RD+

RD-

Z=50�

Z=50

130130

Vcc(+3.3V)

PHY DEVICE

LVPECL

10F

C3C2

1H

67810 9

1 2 3 4 5

1H

TERMINATE AT

DEVICE INPUTS

NOTE:C1=C2=C3=100nF

RxGND

RxVcc

RD-

RD+ TxVcc

TxGND

TD+

TD-

TxDIS

Vcc(+3.3V)

130

LVTTL

Tx Disable

LVTTL

B-1X/1X-155C-F-SSC3(A)

155 Mbps bi-directional SC Receptacle

single Fiber Transceiver

B-1X/1X-155(C)-F-SSC3

20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486

9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213

LUMINENTOIC.COM LUMNDS597-Sep1206

Rev A.5

Recommended Circuit Board Layout

DIMENSION IN MILLIMETER (INCHES)

NOTES:

1.THIS FIGURE DESCRIBE THE RECOMMAND CIRCUIT BOARD LAYOUT FOR THE SFF TRANSCEIVER.

2.THE HATCHED AREAS ARE KEEP-OUT AREAS RESERVED FOR HOUSING STANDOFF. NO METAL

TRACES OR GROUND CONNECTION IN KEEP-OUT AREAS.

3.THE MOUNTING STUDS SHOULD BE SOLDERED TO CHASSIS GROUND FOR MECHANICAL INTEGRITY.

155 Mbps bi-directional SC Receptacle

single Fiber Transceiver

B-1X/1X-155(C)-F-SSC3

20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486

9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213

LUMINENTOIC.COM LUMNDS597-Sep1206

Rev A.5

Warnings

Legal Notice

Package Diagram

PIN 1 PIN 5

PIN 10 PIN 6

Housing Lead

Stand-off

Stud

Housing Lead

Stand-off

Units: mm

B-1X/1X-155(C)-F-SSC3(A)

155 Mbps bi-directional SC Receptacle

single Fiber Transceiver

B-1X/1X-155(C)-F-SSC3

20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486

9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213

LUMINENTOIC.COM LUMNDS597-Sep1206

Rev A.5

Package Diagram

Housing Lead

Stud

PIN 10

Housing Lead

PIN 6

Stand-off

PIN 1

Matel Finger

Stand-off

PIN 5

Units: mm

B-1X/1X-155(C)-F-SSC3S

B-1X/1X-155(C)-F-SSC3AS

155 Mbps bi-directional SC Receptacle

single Fiber Transceiver

B-1X/1X-155(C)-F-SSC3

20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486

9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213

LUMINENTOIC.COM LUMNDS597-Sep1206

Rev A.5

Ordering Information

B - 1X/1X - 155(C) - F - S SC 3 Operating Temperature Shielding Finger -RoHS

• Wavelength

13/15: Tx Wavelength=1310nm

Rx Wavelength=1530nm

15/13: Tx Wavelength=1530nm

Rx Wavelength=1310nm

• Communication protocol

155= LVPECL SD output

155C= LVTTL SD output

• Connector options

• +3.3 V SFF Transceiver

• Single mode ﬁber

• Intermediate Reach

Available Options:

B-13/15-155-F-SSC3

B-15/13-155-F-SSC3

B-13/15-155-F-SSC3A

B-15/13-155-F-SSC3A

B-13/15-155-F-SSC3S

B-15/13-155-F-SSC3S

B-13/15-155-F-SSC3AS

B-15/13-155-F-SSC3AS

• Operating Temperature

Blank = Commercial temperature (0 to 70℃)

A = Commercial temperature (-40 to 85℃)

• Shielding Finger Option

Blank = No shielding ﬁnger

S = with Shielding ﬁnger

Part numbering Deﬁnition:

B-13/15-155-F-SSC3-G5

B-15/13-155-F-SSC3-G5

B-13/15-155-F-SSC3A-G5

B-15/13-155-F-SSC3A-G5

B-13/15-155-F-SSC3S-G5

B-15/13-155-F-SSC3S-G5

B-13/15-155-F-SSC3AS-G5

B-15/13-155-F-SSC3AS-G5

• Ordering Information

Blank = RoHS non-compliant product

G5 = RoHS 5/6-compliant product (lead exemption)

B-13/15-155C-F-SSC3

B-15/13-155C-F-SSC3

B-13/15-155C-F-SSC3A

B-15/13-155C-F-SSC3A

B-13/15-155C-F-SSC3S

B-15/13-155C-F-SSC3S

B-13/15-155C-F-SSC3AS

B-15/13-155C-F-SSC3AS

B-13/15-155C-F-SSC3-G5

B-15/13-155C-F-SSC3-G5

B-13/15-155C-F-SSC3A-G5

B-15/13-155C-F-SSC3A-G5

B-13/15-155C-F-SSC3S-G5

B-15/13-155C-F-SSC3S-G5

B-13/15-155C-F-SSC3AS-G5

B-15/13-155C-F-SSC3AS-G5

155 Mbps bi-directional SC Receptacle

single Fiber Transceiver

B-1X/1X-155(C)-F-SSC3

20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486

9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213

LUMINENTOIC.COM LUMNDS597-Sep1206

Rev A.5

IMPORTANT NOTICE!

All information contained in this document is subject to change without notice, at LuminentOIC’s sole and absolute discretion. LuminentOIC warrants performance

of its products to current speciﬁcations only in accordance with the company’s standard one-year warranty; however, speciﬁcations designated as “preliminary” are

given to describe components only, and LuminentOIC expressly disclaims any and all warranties for said products, including express, implied, and statutory warran-

ties, warranties of merchantability, ﬁtness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company’s Terms and Conditions of

Sale for further warranty information.

LuminentOIC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual

property described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and LuminentOIC makes

no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. Products described in this docu-

ment are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. LuminentOIC customers

using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify LuminentOIC for any damages resulting from

such use or sale.

THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN “AS IS” BASIS. Customer agrees that LuminentOIC is not liable for any

actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact

LuminentOIC to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current.

Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow

guidelines according to proper ESD procedures.

Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation.

Warnings:

Legal Notes: