S29WS064N0LBFW11 - Advanced Micro Devices

Publication Number S29WSxxxN_00 Revision E Amendment 1 Issue Date August 17, 2004

PRELIMINARY

S29WSxxxN MirrorBit™ Flash Family

S29WS256N, S29WS128N, S29WS064N

256/128/64 Megabit (16/8/4 M x 16-Bit) CMOS 1.8 Volt-only

Simultaneous Read/Write, Burst Mode Flash Memory

Distinctive Characteristics

Architectural Advantages

Single 1.8 volt read, program and erase (1.70 to

1.95 volt)

Manufactured on 110 nm MirrorBitTM process

technology

VersatileIO™ (VIO) Feature

— Device generates data output voltages and tolerates

data input voltages as determined by the voltage on

the VIO pin

—V

IO options available for 1.8 V (1.70 V – 1.95 V)

Simultaneous Read/Write operation

— Data can be continuously read from one bank while

executing erase/program functions in another bank

— Zero latency between read and write operations

— Sixteen bank architecture: Each bank consists of

16Mb (WS256N) / 8Mb (WS128N) / 4Mb (WS064N)

Programable Burst Interface

— 2 Modes of Burst Read Operation

— Linear Burst: 32, 16, and 8 words with or without

wrap-around

— Continuous Sequential Burst

SecSiTM (Secured Silicon) Sector region

— 256 words accessible through a command

sequence, 128 words for the Factory SecSi Sector

and 128 words for the Customer SecSi Sector.

— Non-erasable region

Sector Architecture

— S29WS256N: Eight 16 Kword sectors and two-

hundred-fifty-four 64 Kword sectors

— S29WS128N: Eight 16 Kword sectors and one-

hundred-twenty-six 64 Kword sectors

— S29WS064N: Eight 16 Kword sectors and sixty-two

64 Kword sectors

— Banks 0 and 15 each contain 16 Kword sectors and

64 Kword sectors; Other banks each contain 64

Kword sectors

— Eight 16 Kword boot sectors, four at the top of the

address range, and four at the bottom of the address

range

Cycling Endurance: 100,000 cycles per sector

typical

Data Retention: 20 years typical

MCP-Compatible Packages

— 84-ball (8 mm x 11.6 mm) FBGA package for

WS256N

— 84-ball (8 mm x 11.6 mm) FBGA package for

WS128N

— 80-ball (7 mm x 9 mm) FBGA package for WS064N

Performance Characteristics

Read access times at 80/66/54 MHz

— Burst access times of 9/11.2/13.5 ns

— Synchronous initial latency of 69/69/69 ns

— Asynchronous random access times of 70/70/70 ns

Program and Erase Performance

— Typical word programming time of 40 µs

— Typical effective word programming time of 9.4 µs

utilizing a 32-Word Write Buffer at VCC Level

— Typical effective word programming time of 6 µs

utilizing a 32-Word Write Buffer at ACC Level

— Typical sector erase time of 150 ms for 16 Kword

sectors and 600 ms sector erase time for 64 Kword

sectors

Power dissipation (typical values @ 66 MHz)

— Continuous Burst Mode Read: 35 mA

— Simultaneous Operation: 50 mA

—Program: 19 mA

—Erase: 19 mA

— Standby mode: 20 µA

Hardware Features

Sector Protection

— Write protect (WP#) function allows protection of

eight outermost boot sectors, four at top and four at

bottom of memory, regardless of sector protect

status

Handshaking feature available

— Provides host system with minimum possible latency

by monitoring RDY

Boot Option

—Dual Boot

Low VCC write inhibit

Security Features

Advanced Sector Protection consists of the two

following modes of operation

Persistent Sector Protection

— A command sector protection method to lock

combinations of individual sectors to prevent

program or erase operations within that sector

— Sectors can be locked and unlocked in-system at VCC

level

2 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

Password Sector Protection

— A sophisticated sector protection method to lock

combinations of individual sectors to prevent

program or erase operations within that sector using

a user-defined 64-bit password

Software Features

Supports Common Flash Memory Interface (CFI)

Software command set compatible with JEDEC

42.4 standards

Data# Polling and toggle bits

— Provides a software method of detecting program

and erase operation completion

Erase Suspend/Resume

— Suspends an erase operation to read data from, or

program data to, a sector that is not being erased,

then resumes the erase operation

Program Suspend/Resume

— Suspends a programming operation to read data

from a sector other than the one being programmed,

then resume the programming operation

Unlock Bypass Program command

— Reduces overall programming time when issuing

multiple program command sequences

Additional Features

Program Operation

— Ability to perform synchronous and asynchronous

program operation independent of burst control

ACC input

— Acceleration function reduces programming and

erase time in a factory setting.

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 3

Preliminary

General Description

The WSxxxN family consists of 256, 128, and 64 Mbit, 1.8 Volt-only, simultaneous

Read/Write, Burst Mode Flash memory devices, organized as 16, 8, or 4 Mwords

of 16 bits. These devices use a single VCC of 1.70 to 1.95 V to read, program, and

erase the memory array. A 9.0-volt VHH on ACC may be used for faster program

performance in a factory setting. These devices can be programmed in standard

EPROM programmers.

At 80 MHz and 1.8V VIO, the device provides a burst access of 9 ns at 30 pF with

an initial latency of 69 ns at 30 pF. At 66 MHz and 1.8V VIO, the device provides

a burst access of 11.2 ns at 30 pF with an initial latency of 69 ns at 30 pF. At 54

MHz and 1.8V VIO, the device provides a burst access of 13.5 ns at 30 pF with an

initial latency of 69 ns at 30 pF. The device operates within the industrial tem-

perature range of -40°C to +85°C or wireless temperature range of -25°C to

+85°C. These devices are offered in MCP compatible FBGA packages. See the

product selector guide for details

The Simultaneous Read/Write architecture provides simultaneous operation

by dividing the memory space into sixteen banks. The device can improve over-

all system performance by allowing a host system to program or erase in one

bank, then immediately and simultaneously read from another bank, with zero

latency. This releases the system from waiting for the completion of program or

erase operations.

The devices are divided into banks and sectors as shown in the following table:

The VersatileIO™ (VIO) control allows the host system to set the voltage levels

that the device generates at its data outputs and the voltages tolerated at its

data inputs to the same voltage level that is asserted on the VIO pin.

Bank

Quantity of Sectors

(WS256N/WS128N/WS064N) Sector Size

04/4/4 16 Kwords

15/7/3 64 Kwords

116/8/4 64 Kwords

216/8/4 64 Kwords

316/8/4 64 Kwords

416/8/4 64 Kwords

516/8/4 64 Kwords

616/8/4 64 Kwords

716/8/4 64 Kwords

816/8/4 64 Kwords

916/8/4 64 Kwords

10 16/8/4 64 Kwords

11 16/8/4 64 Kwords

12 16/8/4 64 Kwords

13 16/8/4 64 Kwords

14 16/8/4 64 Kwords

15 15/7/3 64 Kwords

4/4/4 16 Kwords

4 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

The device uses Chip Enable (CE#), Write Enable (WE#), Address Valid (AVD#)

and Output Enable (OE#) to control asynchronous read and write operations.

For burst operations, the device additionally requires Ready (RDY), and Clock

(CLK). This implementation allows easy interface with minimal glue logic to a

wide range of microprocessors/microcontrollers for high performance read

operations.

The burst read mode feature gives system designers flexibility in the interface to

the device. The user can preset the burst length and then wrap or non-wrap

through the same memory space, or read the flash array in continuous mode.

The device is entirely command set compatible with the JEDEC 42.4 single-

power-supply Flash standard. Commands are written to the command regis-

ter using standard microprocessor write timing. Register contents serve as

inputs to an internal state-machine that controls the erase and programming

circuitry. Write cycles also internally latch addresses and data needed for the

programming and erase operations. Reading data out of the device is similar to

reading from other Flash or EPROM devices.

Device programming occurs by executing the program command sequence. This

initiates the Embedded Program Algorithm — an internal algorithm that auto-

matically times the program pulse widths and verifies proper cell margin. The

Unlock Bypass mode facilitates faster program times by requiring only two

write cycles to program data instead of four. The additional Write Buffer Pro-

gramming feature provides superior programming performance by grouping

locations being programmed.

Device erasure occurs by executing the erase command sequence. This initiates

the Embedded Erase Algorithm — an internal algorithm that automatically pre-

programs the array (if it is not already fully programmed) before executing the

erase operation. During erase, the device automatically times the erase pulse

widths and verifies proper cell margin.

The Program Suspend/Program Resume feature enables the user to put

program on hold to read data from any sector that is not selected for program-

ming. If a read is needed from the SecSi Sector area, Persistent Protection area,

Dynamic Protection area, or the CFI area, after an program suspend, then the

user must use the proper command sequence to enter and exit this region. The

program suspend/resume functionality is also available when programming in

erase suspend (1 level depth only).

The Erase Suspend/Erase Resume feature enables the user to put erase on

hold to read data from, or program data to, any sector that is not selected for

erasure. True background erase can thus be achieved. If a read is needed from

the SecSi Sector area, Persistent Protection area, Dynamic Protection area, or

the CFI area, after an erase suspend, then the user must use the proper com-

mand sequence to enter and exit this region.

The hardware RESET# pin terminates any operation in progress and resets

the internal state machine to reading array data. The RESET# pin may be tied to

the system reset circuitry. A system reset would thus also reset the device, en-

abling the system microprocessor to read boot-up firmware from the Flash

memory device.

The host system can detect whether a memory array program or erase opera-

tion is complete by using the device status bit DQ7 (Data# Polling), DQ6/DQ2

(toggle bits), DQ5 (exceeded timing limit), DQ3 (sector erase start timeout state

indicator), and DQ1 (write to buffer abort). After a program or erase cycle has

been completed, the device automatically returns to reading array data.

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 5

Preliminary

The sector erase architecture allows memory sectors to be erased and repro-

grammed without affecting the data contents of other sectors. The device is

fully erased when shipped from the factory.

Hardware data protection measures include a low VCC detector that automat-

ically inhibits write operations during power transitions. The device also offers

two types of data protection at the sector level. When at VIL, WP# locks the

four outermost boot sectors at the top of memory and the four outermost boot

sectors at the bottom of memory.

When the ACC pin = VIL, the entire flash memory array is protected.

The device offers two power-saving features. When addresses have been stable

for a specified amount of time, the device enters the automatic sleep mode.

The system can also place the device into the standby mode. Power consump-

tion is greatly reduced in both modes.

SpansionTM Flash memory products combine years of Flash memory manufactur-

ing experience to produce the highest levels of quality, reliability and cost

effectiveness. The device electrically erases all bits within a sector. The data is

programmed using hot electron injection.

6 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

Table of Contents

Product Selector Guide. . . . . . . . . . . . . . . . . . . . . . 8

Block Diagram of

Simultaneous Operation Circuit . . . . . . . . . . . . . . .9

Connection Diagrams . . . . . . . . . . . . . . . . . . . . . . 10

MCP Look-ahead Connection Diagram ......................................... 13

Multi-Chip Compatible Packages ......................................................14

Special Handling Instructions for FBGA Package .........................14

Input/Output Descriptions . . . . . . . . . . . . . . . . . . . 15

Logic Symbol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Ordering Information (256 Mb) . . . . . . . . . . . . . . . 17

Ordering Information (128 Mb) . . . . . . . . . . . . . . . 18

Ordering Information (64 Mb) . . . . . . . . . . . . . . . . 19

Device Bus Operations . . . . . . . . . . . . . . . . . . . . . .20

Table 1. Device Bus Operations ...........................................20

VersatileIO™ (V

) Control ...............................................................20

Requirements for Asynchronous (Non-Burst)

Read Operation .....................................................................................20

Requirements for Synchronous (Burst) Read Operation ......... 21

Table 2. Address Dependent Additional Latency ....................21

Table 3. Address Latency for x Wait States (

≤

80 MHz) ...........21

Table 4. Address Latency for 6 Wait States (

≤

80 MHz) ..........22

Table 5. Address Latency for 5 Wait States (

≤

68 MHz) ..........22

Table 6. Address Latency for 4 Wait States (

≤

54 MHz) ..........22

Table 7. Address Latency for 3 Wait States (

≤

40 MHz) ..........22

Table 8. Address/Boundary Crossing Latency for 6 Wait States

(

≤

80 MHz) .......................................................................22

Table 9. Address/Boundary Crossing Latency for 5 Wait States

(< 68 MHz) ......................................................................23

Table 10. Address/Boundary Crossing Latency for 4 Wait States

(< 54 MHz) ......................................................................23

Table 11. Address/Boundary Crossing Latency for 3 Wait States

(< 40 MHz) ......................................................................23

Table 12. Burst Address Groups ..........................................24

Configuration Register ........................................................................24

Handshaking ...........................................................................................24

Simultaneous Read/Write Operations with Zero Latency ...... 25

Writing Commands/Command Sequences .................................. 25

Accelerated Program/Chip Erase Operations ............................. 25

Write Buffer Programming Operation .......................................... 26

Autoselect Mode .................................................................................. 27

Advanced Sector Protection and Unprotection .........................28

Sector Protection ................................................................................. 29

Persistent Sector Protection ............................................................. 29

Table 13. Sector Protection Schemes ...................................31

Password Sector Protection ............................................................. 32

Lock Register ..........................................................................................33

Table 14. WS256N Lock Register .........................................33

Table 15. WS128N/064N Lock Register ................................33

Hardware Data Protection Mode ....................................................33

Standby Mode ........................................................................................ 34

Automatic Sleep Mode ........................................................................ 34

RESET#: Hardware Reset Input ....................................................... 34

Output Disable Mode ...........................................................................35

SecSi™ (Secured Silicon) Sector Flash

Memory Region . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Table 16. SecSi

Sector Addresses ......................................36

Common Flash Memory Interface (CFI). . . . . . . 36

Table 17. CFI Query Identification String ............................. 38

Table 18. System Interface String ...................................... 38

Table 20. Primary Vendor-Specific Extended Query ............... 39

Table 21. WS256N Sector & Memory Address Map ................ 41

Table 22. WS128N Sector & Memory Address Map ................ 49

Table 23. WS064N Sector & Memory Address Map ................ 53

Command Definitions . . . . . . . . . . . . . . . . . . . . . . 55

Reading Array Data ............................................................................. 55

Set Configuration Register Command Sequence ....................... 55

Read Configuration Register Command Sequence .................... 56

Figure 1. Synchronous/Asynchronous State Diagram ............. 56

Table 24. Programmable Wait State Settings ....................... 57

Table 25. Wait States for Handshaking ................................ 57

Table 26. Burst Length Configuration .................................. 58

Table 27. Configuration Register ........................................ 59

Reset Command ................................................................................... 59

Autoselect Command Sequence ......................................................60

Table 28. Autoselect Addresses .......................................... 61

Enter SecSi™ Sector/Exit SecSi Sector Command Sequence ... 61

Word Program Command Sequence ..............................................61

Figure 2. Word Program Operation ...................................... 62

Write Buffer Programming Command Sequence ....................... 62

Table 29. Write Buffer Command Sequence ......................... 63

Figure 3. Write Buffer Programming Operation...................... 64

Chip Erase Command Sequence ...................................................... 65

Sector Erase Command Sequence .................................................. 65

Figure 4. Erase Operation .................................................. 66

Erase Suspend/Erase Resume Commands .................................... 67

Program Suspend/Program Resume Commands ........................ 67

Lock Register Command Set Definitions ......................................68

Password Protection Command Set Definitions ........................68

Non-Volatile Sector Protection Command Set Definitions .... 69

Figure 5. PPB Program/Erase Algorithm ............................... 71

Global Volatile Sector Protection Freeze Command Set ........ 72

Volatile Sector Protection Command Set .................................... 72

SecSi Sector Entry Command ............................................................73

Command Definition Summary ........................................................ 74

Table 30. Memory Array Commands .................................. 74

Table 31. Sector Protection Commands ............................... 75

Write Operation Status . . . . . . . . . . . . . . . . . . . . . 76

Figure 6. Polling Flow Chart ................................................ 76

DQ7: Data# Polling .............................................................................. 77

DQ6: Toggle Bit I .................................................................................. 77

DQ2: Toggle Bit II ................................................................................ 78

Table 32. DQ6 and DQ2 Indications .................................... 78

Reading Toggle Bits DQ6/DQ2 ........................................................ 79

DQ5: Exceeded Timing Limits .......................................................... 79

DQ3: Sector Erase Start Timeout State Indicator ..................... 79

DQ1: Write to Buffer Abort .............................................................80

Table 33. Write Operation Status ....................................... 80

Absolute Maximum Ratings . . . . . . . . . . . . . . . . . 81

Figure 7. Maximum Negative Overshoot Waveform................ 81

Figure 8. Maximum Positive Overshoot Waveform ................. 81

Operating Ranges . . . . . . . . . . . . . . . . . . . . . . . . . 81

DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . .82

Test Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

Figure 9. Test Setup.......................................................... 83

Table 34. Test Specifications ............................................. 83

Key to Switching Waveforms. . . . . . . . . . . . . . . . 83

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 7

Preliminary

Switching Waveforms . . . . . . . . . . . . . . . . . . . . . . 83

Figure 10. Input Waveforms and Measurement Levels............ 83

VCC Power-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

Figure 11. V

Power-up Diagram ....................................... 84

AC Characteristics—Synchronous . . . . . . . . . . . 85

CLK Characterization ......................................................................... 85

Figure 12. CLK Characterization .......................................... 85

Synchronous/Burst Read ....................................................................86

Timing Diagrams ................................................................................... 87

Figure 13. CLK Synchronous Burst Mode Read ...................... 87

Figure 14. 8-word Linear Burst with Wrap Around ................. 88

Figure 15. 8-word Linear Burst without Wrap Around............. 88

Figure 16. Linear Burst with RDY Set One Cycle Before Data... 89

AC Characteristics—Asynchronous. . . . . . . . . . . 90

Asynchronous Mode Read .................................................................90

Timing Diagrams ...................................................................................90

Figure 17. Asynchronous Mode Read with Latched Addresses .. 90

Figure 18. Asynchronous Mode Read ................................... 91

Hardware Reset (RESET#) .................................................................91

Figure 19. Reset Timings ................................................... 91

Erase/Program Timing ......................................................................... 92

Figure 20. Asynchronous Program Operation Timings: WE#

Latched Addresses ............................................................ 93

Figure 21. Synchronous Program Operation Timings:

CLK Latched Addresses...................................................... 94

Figure 22. Accelerated Unlock Bypass Programming Timing .... 95

Figure 23. Data# Polling Timings

(During Embedded Algorithm) ............................................ 95

Figure 24. Toggle Bit Timings

(During Embedded Algorithm) ............................................ 96

Figure 25. Synchronous Data Polling Timings/

Toggle Bit Timings ............................................................ 96

Figure 26. DQ2 vs. DQ6..................................................... 97

Figure 27. Latency with Boundary Crossing when

Frequency > 66 MHz ......................................................... 97

Figure 28. Latency with Boundary Crossing into Program/

Erase Bank ...................................................................... 98

Figure 29. Example of Wait States Insertion ......................... 99

Figure 30. Back-to-Back Read/Write Cycle Timings.............. 100

Erase and Programming Performance . . . . . . . . 101

BGA Ball Capacitance. . . . . . . . . . . . . . . . . . . . . 102

Physical Dimensions (256 Mb and 128 Mb) . . . . . 103

VBH084—84-ball Fine-Pitch Ball Grid Array (FBGA)

8 x 11.6 mm MCP Compatible Package .........................................103

Physical Dimensions (64 Mb) . . . . . . . . . . . . . . . . 104

TBD—80-ball Fine-Pitch Ball Grid Array (FBGA) 7x9 mm

MCP Compatible Package .................................................................104

Revision Summary. . . . . . . . . . . . . . . . . . . . . . . . 105

8 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

Product Selector Guide

Note:

80 MHz available for standalone applications only, 66 MHz and 54 MHz available for both multi-chip and standalone applications.

Block Diagram

Part Number

S29WS256N, S29WS128N, S29WS064N

Speed Option (Burst Frequency) (See Note)

80 MHz 66 MHz 54 MHz

Max Synchronous Latency, ns (t

IACC

)69 69 69

Max Synchronous Burst Access Time, ns (t

BACC

) 9 11.2 13.5

Max Asynchronous Access Time t

), ns 70 70 70

Max CE# Access Time, ns (t

), ns 70 70 70

Max OE# Access Time, ns (t

)11.2 11.2 13.5

Input/Output

Buffers

X-Decoder

Y-Decoder

Chip Enable

Output Enable

Logic

Erase Voltage

Generator

PGM Voltage

Generator

Timer

Detector

State

Control

Command

WE#

RESET#

WP#

ACC

CE#

OE#

DQ15–DQ0

Data

Latch

Y-Gating

Cell Matrix

Address Latch

max

–A0*

RDY

Buffer RDY

Burst

State

Control

Burst

Address

Counter

AVD#

CLK

* WS256N: A23-A0

WS128N: A22-A0

WS064N: A21-A0

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 9

Preliminary

Block Diagram of

Simultaneous Operation Circuit

Note: Amax=A23 for the WS256N, A22 for the WS128N, and A21 for the WS064N.

Bank Address

RESET#

ACC

WE#

CE#

AVD#

RDY

DQ15–DQ0

WP#

STATE

CONTROL

COMMAND

Bank 1

X-Decoder

Y-Decoder

Latches and

Control Logic

Bank 0

X-Decoder

Y-Decoder

Latches and

Control Logic

DQ15–DQ0

Bank 14

Y-Decoder

X-Decoder

Latches and

Control Logic

Bank 15

Y-Decoder

X-Decoder

Latches and

Control Logic

OE#

Status

Control

Amax–A0

Bank Address

10 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

Connection Diagrams

DQ8 DQ14

RFU

RFU ACC WE# A8 A11

C3 C4 C5 C6 C7 C8

A6 RFU RESET# RFU A19 A12 A15

D2 D3 D4 D5 D6 D7 D8 D9

A5 A18 RDY A20 A9 A13 A21

E2 E3 E4 E5 E6 E7 E8 E9

A1 A4 A17 A10 A14 A22

F2 F3 F4 F7 F8 F9

VSS DQ1A0 DQ6 RFU A16

G3 G4G2 G7 G8 G9

CE#f1

DQ0

OE# DQ9 DQ3 DQ4 DQ13 DQ15 RFU

H2 H3 H4 H5 H6 H7 H8 H9

DQ10 VCC RFU DQ12 DQ7 VSS

J2 J3 J4 J5 J6 J7 J8 J9

DQ2 DQ11 RFU DQ5

K3 K8

K4 K5 K6 K7

RFU A23

RFU RFU

RFU CLK RFU RFU RFU RFU

B3 B4 B5 B6 B7 B8

RFU RFU VCC RFU RFU RFU

L3 L4 L5 L6 L7 L8

B2 B9

K2 K9

L9L2

AVD# RFU

RFU

WP#

RFU

A1 A10

M1 M10

S29WS256N–MCP Compatible

84-ball Fine-Pitch Ball Grid Array

(Top View, Balls Facing Down)

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 11

Preliminary

DQ8 DQ14

RFU

RFU ACC WE# A8 A11

C3 C4 C5 C6 C7 C8

A6 RFU RESET# RFU A19 A12 A15

D2 D3 D4 D5 D6 D7 D8 D9

A5 A18 RDY A20 A9 A13 A21

E2 E3 E4 E5 E6 E7 E8 E9

A1 A4 A17 A10 A14 A22

F2 F3 F4 F7 F8 F9

VSS DQ1A0 DQ6 RFU A16

G3 G4G2 G7 G8 G9

CE#f1

DQ0

OE# DQ9 DQ3 DQ4 DQ13 DQ15 RFU

H2 H3 H4 H5 H6 H7 H8 H9

DQ10 VCC RFU DQ12 DQ7 VSS

J2 J3 J4 J5 J6 J7 J8 J9

DQ2 DQ11 RFU DQ5

K3 K8

K4 K5 K6 K7

RFU RFU

RFU CLK RFU RFU RFU RFU

B3 B4 B5 B6 B7 B8

RFU RFU VCC RFU RFU RFU

L3 L4 L5 L6 L7 L8

B2 B9

K2 K9

L9L2

AVD# RFU

RFU

WP#

RFU

A1 A10

M1 M10

S29WS128N–MCP Compatible

84-ball Fine-Pitch Ball Grid Array

(Top View, Balls Facing Down)

12 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

DQ8 DQ14

RFU

RFU ACC WE# A8 A11

B2 B3 B4 B5 B6 B7

A6 RFU RESET# RFU A19 A12 A15

C1 C2 C3 C4 C5 C6 C7 C8

A5 A18 RDY A20 A9 A13 A21

D1 D2 D3 D4 D5 D6 D7 D8

A1 A4 A17 A10 A14 RFU

E1 E2 E3 E6 E7 E8

DQ1A0 DQ6 RFU A16

F2 F3F1 F6 F7 F8

CE#f1

DQ0

OE# DQ9 DQ3 DQ4 DQ13 DQ15 RFU

G1 G2 G3 G4 G5 G6 G7 G8

DQ10 V

RFU DQ12 DQ7 V

H1 H2 H3 H4 H5 H6 H7 H8

DQ2 DQ11 RFU DQ5

J2 J7

J3 J4 J5 J6

RFU RFU

RFU CLK RFU RFU RFU RFU

A2 A3 A4 A5 A6 A7

RFU RFU V

RFU RFU RFU

K2 K3 K4 K5 K6 K7

A1 A8

J1 J8

K8K1

AVD# RFU

RFU

WP#

RFU

S29WS064N–MCP Compatible

80-ball Fine-Pitch Ball Grid Array

(Top View, Balls Facing Down)

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 13

Preliminary

MCP Look-ahead Connection Diagram

Note: To provide customers with a migration path to higher densities and an option to stack more die in a package,

Spansion has prepared a standard pinout that supports



NOR Flash and SRAM densities up to 4 Gigabits



NOR Flash and pSRAM densities up to 4 Gigabits



NOR Flash and pSRAM and DATA STORAGE densities up to 4 Gigabits



See MCP data sheet (publication number S71WS256_512NC0) for input/output descriptions.

The signal locations of the resultant MCP device are shown above. Note that for different densities, the actual package

outline may vary. Any pinout in any MCP, however, will be a subset of the pinout above.

In some cases, there may be outrigger balls in locations outside the grid shown above. In such cases, treat them as

reserved and do not connect them to any other signal.

For any further inquiries about the above look-ahead pinout, please refer to the application note on this subject or con-

tact your sales office.

J4 J5 J6 J7 J8 J2

H7 H8 H9

G7 G8 G9

F7 F8 F9

E7 E8 E9

K2 K3

D6 D7

CE#f1

OE#

CE1#s1 DQ0

D2 D3

C2 C3

AVD# VSSds

WP# A7 A8WE#WP/ACCLB#s

C4 C5

C6 C7

D8 D9

CE1#dsA11

C8 C9

RY/BY#dsCLKdsRESET#dsVCCdsCE#f2CLK

A15A12A19

A21A13A9

A22A14A10

A16 A24DQ6

CE2s1

A20

A23

CE2s2

H4 H5

G4 G5

F4 F5

RESET#fUB#s

RDYA18

CE1#s2A17

VCCs2DQ1

CREsDQ15DQ13DQ4DQ3DQ9

K4 K5

K7 K8 K9

DQ7VCCs1VCCfDQ10

H2 H3

G2 G3

F2 F3

E2 E3

A6A3

A5A2

A4A1

VSSA0

L4 L5 L6 L7 L8 L9

M2 M3

VCCnds DQ8

A27 A26

VSSDQ12

LOCK

or WP#/ACCds

DQ14DQ5A25DQ11DQ2

M5 M6 M7 M8 M9

or VCCQds

VCCQs1CE2#dsVCCfVSSnds DNU

N10

Legend:

Data-storage Only

Shared

or NC (not connected)

Flash Shared Only

1st Flash Only

2nd Flash Only

K5 K6

B10

A10

P10

1st RAM Only

2nd RAM Only

RAM Shared Only

DoC Only

NC or ds

96-ball Fine-Pitch Ball Grid Array

(Top View, Balls Facing Down)

14 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

Multi-Chip Compatible Packages

For this family of products, a single multi-chip compatible package is offered for

each density to allow both standalone and multi-chip qualification using a single,

adaptable package. This new methodology allows package standardization re-

sulting in faster development. The multi-chip compatible package includes all the

pins required for standalone device operation and verification. In addition, extra

pins are included for insertion of common data storage or logic devices to be used

for multi-chip products. If a standalone device is required, the extra multi-chip

specific pins are not connected and the standalone device operates normally. The

multi-chip compatible package sizes were chosen to serve the largest number of

combinations possible. There are only a few cases where a larger package size

would be required to accommodate the multi-chip combination. This multi-chip

compatible package set does not allow for direct package migration from legacy

products.

Special Handling Instructions for FBGA Package

Special handling is required for Flash Memory products in FBGA packages.

Flash memory devices in FBGA packages may be damaged if exposed to ultra-

sonic cleaning methods. The package and/or data integrity may be compromised

if the package body is exposed to temperatures above 150°C for prolonged peri-

ods of time.

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 15

Preliminary

Input/Output Descriptions

A23-A0 = Address inputs for WS256N (A22-A0 for WS128 and

A21-A0 for WS064N).

DQ15-DQ0 = Data input/output.

CE#f1 = Chip Enable input. Asynchronous relative to CLK for

the Burst mode.

OE# = Output Enable input. Asynchronous relative to CLK

for the Burst mode.

WE# = Write Enable input.

VCC = Device Power Supply.

VSS = Ground.

NC = No Connect; not connected internally.

RDY = Ready output. Indicates the status of the Burst read.

CLK = Clock input. In burst mode, after the initial word is

output, subsequent active edges of CLK increment

the internal address counter. Should be at VIL or VIH

while in asynchronous mode.

AVD# = Address Valid input. Indicates to device that the

valid address is present on the address inputs.

Low = for asynchronous mode, indicates valid

address; for burst mode, causes starting address to

be latched.

High = device ignores address inputs.

RESET# = Hardware reset input. Low = device resets and

returns to reading array data.

WP# = Hardware write protect input. At VIL, disables

program and erase functions in the four outermost

sectors. Should be at VIH for all other conditions.

ACC = Accelerated input. At VHH, accelerates.

programming; automatically places device in unlock

bypass mode. At VIL, disables all program and erase

functions. Should be at VIH for all other conditions.

RFU = Reserved for future use (see MCP look-ahead pinout

for use with MCP).

16 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

Logic Symbol

Max*+1

DQ15–DQ0

Amax*–A0

CE#

OE#

WE#

RESET#

CLK

RDY

AVD#

WP#

ACC

* max = 23 for the WS256N, 22 for the WS128N, and

21 for the WS064N.

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 17

Preliminary

Ordering Information (256 Mb)

The ordering part number is formed by a valid combination of the following:

S29WS 256 N 0S BA W 01 0

PACKING TYPE

0 = Tray (standard; see Note 1)

2 = 7-inch Tape and Reel

3 = 13-inch Tape and Reel

MODEL NUMBER (Note 3)

(VIO Range, Ball Count, Package Dimensions, DYB Protect/Unprotect After

Power-up)

01 = 1.8 V V

, 84-ball, 8 mm x 11.6 mm, DYB Unprotect

11 = 1.8 V V

, 84-ball, 8 mm x 11.6 mm, DYB Protect

TEMPERATURE RANGE (Note 3)

W = Wireless (-25

C to +85

I = Industrial (–40

C to +85

PACKAGE TYPE AND MATERIAL

BA = Very Thin Fine-Pitch BGA, Lead (Pb)-free Compliant Package

BF = Very Thin Fine-Pitch BGA, Lead (Pb)-free Package

SPEED OPTION (BURST FREQUENCY)

0S = 80 MHz

0P = 66 MHz

0L = 54 MHz

PROCESS TECHNOLOGY

N = 110 nm MirrorBit™ Technology

FLASH DENSITY

256 = 256 Mb

DEVICE FAMILY

S29WS = 1.8 Volt-only Simultaneous Read/Write, Burst Mode Flash Memory

S29WS256N Valid Combinations

VIO Range

DYB

Power Up

State

Package Type

(Note 2)

Base Ordering

Part Number

Speed

Option

Package Type, Material, &

Temperature Range

Model

Number

Packing

Type

S29WS256N 0S, 0P, 0L BAW (

Lead (Pb)-free Compliant),

BFW (

Lead (Pb)-free)

01 0, 2, 3

(Note 1) 1.70–1.95 V

Unprotect 8 mm x 11.6 mm

84-ball

MCP-Compatible

11 Protect

Notes:

1. Type 0 is standard. Specify other options as required.

2. BGA package marking omits leading “S29” and packing type

designator from ordering part number.

3. For 1.5 VIO option, other boot options, or industrial temperature

range, contact your local sales office.

Valid Combinations

Valid Combinations list configurations planned to be supported in vol-

ume for this device. Consult your local sales office to confirm avail-

ability of specific valid combinations and to check on newly released

combinations.

18 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

Ordering Information (128 Mb)

The ordering part number is formed by a valid combination of the following:

S29WS 128 N 0S BA W 01 0

PACKING TYPE

0 = Tray (standard; see note 1)

2 = 7-inch Tape and Reel

3 = 13-inch Tape and Reel

MODEL NUMBER (Note 3)

(VIO Range, Ball Count, Package Dimensions, DYB Protect/Unprotect After

Power-up)

01 = 1.8 V V

, 84-ball, 8 mm x 11.6 mm, DYB Unprotect

11 = 1.8 V V

, 84-ball, 8 mm x 11.6 mm, DYB Protect

TEMPERATURE RANGE (Note 3)

W = Wireless (-25

C to +85

I = Industrial (–40

C to +85

PACKAGE TYPE AND MATERIAL

BA = Very Thin Fine-Pitch BGA, Lead (Pb)-free Compliant Package

BF = Very Thin Fine-Pitch BGA, Lead (Pb)-free Package

SPEED OPTION (BURST FREQUENCY)

0S = 80 MHz

0P = 66 MHz

0L = 54 MHz

PROCESS TECHNOLOGY

N = 110 nm MirrorBit™ Technology

FLASH DENSITY

128 = 128 Mb

DEVICE FAMILY

S29WS = 1.8 Volt-only Simultaneous Read/Write, Burst Mode Flash Memory

S29WS128N Valid Combinations

VIO Range

DYB

Power Up

State

Package Type

(Note 2)

Base Ordering

Part Number

Speed

Option

Package Type, Material, &

Temperature Range

Model

Number

Packing

Type

S29WS128N 0S, 0P, 0L BAW (

Lead (Pb)-free Compliant),

BFW (

Lead (Pb)-free)

01 0, 2, 3

(Note 1) 1.70–1.95 V

Unprotect 8 mm x 11.6 mm

84-ball

MCP Compatible

11 Protect

Notes:

1. Type 0 is standard. Specify other options as required.

2. BGA package marking omits leading “S29” and packing type

designator from ordering part number.

3. For 1.5 VIO option, other boot options, or industrial temperature

range, contact your local sales office.

Valid Combinations

Valid Combinations list configurations planned to be supported in vol-

ume for this device. Consult your local sales office to confirm avail-

ability of specific valid combinations and to check on newly released

combinations.

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 19

Preliminary

Ordering Information (64 Mb)

The ordering part number is formed by a valid combination of the following:

S29WS 064 N 0S BA W 01 0

PACKING TYPE

0 = Tray (standard; see note 1)

2 = 2-inch Tape and Reel

3 = 3-inch Tape and Reel

MODEL NUMBER (Note 3)

(VIO Range, Ball Count, Package Dimensions, DYB Protect/Unprotect After

Power-up)

01 = 1.8 V V

, 80-ball, 7 mm x 9 mm, DYB Unprotect

11 = 1.8 V V

, 80-ball, 7 mm x 9 mm, DYB Protect

TEMPERATURE RANGE (Note 3)

W = Wireless (-25

C to +85

I = Industrial (–40

C to +85

PACKAGE TYPE AND MATERIAL

BA = Very Thin Fine-Pitch BGA, Lead (Pb)-free Compliant Package

BF = Very Thin Fine-Pitch BGA, Lead (Pb)-free Package

SPEED OPTION (BURST FREQUENCY)

0S = 80 MHz

0P = 66 MHz

0L = 54 MHz

PROCESS TECHNOLOGY

N = 110 nm MirrorBit™ Technology

FLASH DENSITY

064 = 64 Mb

DEVICE FAMILY

S29WS = 1.8 Volt-only Simultaneous Read/Write, Burst Mode Flash Memory

S29WS064N Valid Combinations

VIO Range

DYB

Power Up

State

Package Type

(Note 2)

Base Ordering

Part Number

Speed

Option

Package Type, Material, &

Temperature Range

Model

Number

Packing

Type

S29WS064N 0S, 0P, 0L BAW (

Lead (Pb)-free Compliant),

BFW (

Lead (Pb)-free)

01 0, 2, 3

(Note 1) 1.70–1.95 V

Unprotect 7 mm x 9 mm

80-ball

MCP-Compatible

11 Protect

Notes:

1. Type 0 is standard. Specify other options as required.

2. BGA package marking omits leading “S29” and packing type

designator from ordering part number.

3. For 1.5 VIO option, other boot options, or industrial temperature

range, contact your local sales office.

Valid Combinations

Valid Combinations list configurations planned to be supported in vol-

ume for this device. Consult your local sales office to confirm avail-

ability of specific valid combinations and to check on newly released

combinations.

20 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

Device Bus Operations

This section describes the requirements and use of the device bus operations,

which are initiated through the internal command register. The command register

itself does not occupy any addressable memory location. The register is com-

posed of latches that store the commands, along with the address and data

information needed to execute the command. The contents of the register serve

as inputs to the internal state machine. The state machine outputs dictate the

function of the device. Table 1 lists the device bus operations, the inputs and con-

trol levels they require, and the resulting output. The following subsections

describe each of these operations in further detail.

Ta b le 1 . Device Bus Operations

Legend: L = Logic 0, H = Logic 1, X = Don’t Care.

VersatileIO™ (VIO) Control

The VersatileIO (VIO) control allows the host system to set the voltage levels that

the device generates at its data outputs and the voltages tolerated at its data in-

puts to the same voltage level that is asserted on the VIO pin.

Requirements for Asynchronous (Non-Burst)

Read Operation

To read data from the memory array, the system must first assert a valid address

on A23–A0 for WS256N (A22–A0 for the WS128N, A21–A0 for WS064N), while

driving AVD# and CE# to VIL. WE# should remain at VIH. The rising edge of AVD#

latches the address. The data will appear on DQ15–DQ0.

Address access time (tACC) is equal to the delay from stable addresses to valid

output data. The chip enable access time (tCE) is the delay from the stable CE#

to valid data at the outputs. The output enable access time (tOE) is the delay from

the falling edge of OE# to valid data at the output.

The internal state machine is set for reading array data in asynchronous mode

upon device power-up, or after a hardware reset. This ensures that no spurious

alteration of the memory content occurs during the power transition.

Operation

CE# OE# WE# Addresses DQ15–0 RESET# CLK AVD#

Asynchronous Read - Addresses Latched L L H Addr In I/O H X

Asynchronous Read - Addresses Steady State L L H Addr In I/O H X L

Asynchronous Write L H L Addr In I/O HX L

Synchronous Write L H L Addr In I/O H

Standby (CE#) H X X X HIGH Z H X X

Hardware Reset X X X X HIGH Z L X X

Burst Read Operations (Synchronous)

Load Starting Burst Address L X H Addr In X H

Advance Burst to next address with

appropriate Data presented on the Data Bus L L H X Burst

Data Out H H

Terminate current Burst read cycle H X H X HIGH Z H X

Terminate current Burst read cycle via RESET# X X H X HIGH Z L X X

Terminate current Burst read cycle and start

new Burst read cycle L X H Addr In I/O H

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 21

Preliminary

Requirements for Synchronous (Burst) Read Operation

The device is capable of continuous sequential burst read and linear burst read

of a preset length. When the device first powers up, it is enabled for asynchro-

nous read operation.

Prior to entering burst mode, the system should determine how many wait states

are desired for the initial word (tIACC) of each burst access, what mode of burst

operation is desired, and how the RDY signal will transition with valid data. The

system would then write the configuration register command sequence. See Set

Configuration Register Command Sequence for further details.

The initial word is output tIACC after the active edge of the first CLK cycle. Sub-

sequent words are output tBACC after the active edge of each successive clock

cycle at which point the internal address counter is automatically incremented.

Note that the device has a fixed internal address boundary that occurs every 128

words, starting at address 00007Fh. No boundary crossing latency is required

when the device operates at or below 66 MHz to reach address 000080h. When

the device operates above 66 MHz, a boundary crossing of one additional wait

state is required. The timing diagram can be found in Figure 27.

When the starting burst address is not divisible by four, additional waits are re-

quired. For example, if the starting burst address is divisible by four A1:0 = 00,

no additional wait state is required, but if the starting burst address is at address

A1:0 = 01, 10, or 11, one, two or three wait states are required, respectively,

until data D4 is read. The RDY output indicates this condition to the system by

deasserting (see Table 2).

Ta b le 2 . Address Dependent Additional Latency

Table 3 shows the address latency for variable wait state scheme, as imple-

mented in WS256N.

Ta bl e 3 . Address Latency for x Wait States (≤ 80 MHz)

Initial

Address

A[10]

Cycle

XX+1 X+2 X+3 X+4 X+5 X+6

00 D0 D1 D2 D3 D4 D5 D6

01 D1 D2 D3 — D4 D5 D6

10 D2 D3 — — D4 D5 D6

11 D3 — — — D4 D5 D6

Word Wait

States Cycle

0 x ws D0 D1 D2 D3 D4 D5 D6 D7 D8

1 x ws D1 D2 D3 1 ws D4 D5 D6 D7 D8

2 x ws D2 D3 1 ws 1 ws D4 D5 D6 D7 D8

3 x ws D3 1 ws 1 ws 1 ws D4 D5 D6 D7 D8

22 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

Tables 4–7 show the address latency for variable wait state scheme, as imple-

mented in WS128N and WS064N.

Ta bl e 4 . Address Latency for 6 Wait States (≤ 80 MHz)

Ta bl e 5 . Address Latency for 5 Wait States (≤ 68 MHz)

Ta bl e 6 . Address Latency for 4 Wait States (≤ 54 MHz)

Ta bl e 7 . Address Latency for 3 Wait States (≤ 40 MHz)

Tables 8-11 show the address/boundary crossing latency for variable wait state

if a boundary crossing occurs during initial access as implemented in WS128N

and WS064N.

Ta bl e 8 . Address/Boundary Crossing Latency for 6 Wait States (≤ 80 MHz)

Word Wait

States Cycle

0 6 ws D0 D1 D2 D3 D4 D5 D6 D7 D8

1 6 ws D1 D2 D3 1 ws D4 D5 D6 D7 D8

2 6 ws D2 D3 1 ws 1 ws D4 D5 D6 D7 D8

3 6 ws D3 1 ws 1 ws 1 ws D4 D5 D6 D7 D8

Word Wait

States Cycle

0 5 ws D0 D1 D2 D3 D4 D5 D6 D7 D8

1 5 ws D1 D2 D3 D4 D5 D6 D7 D8 D9

2 5 ws D2 D3 1 ws D4 D5 D6 D7 D8 D9

3 5 ws D3 1 ws 1 ws D4 D5 D6 D7 D8 D9

Word Wait

States Cycle

0 4 ws D0 D1 D2 D3 D4 D5 D6 D7 D8

1 4 ws D1 D2 D3 D4 D5 D6 D7 D8 D9

2 4 ws D2 D3 D4 D5 D6 D7 D8 D9 D10

3 4 ws D3 1 ws D4 D5 D6 D7 D8 D9 D10

Word Wait

States Cycle

0 3 ws D0 D1 D2 D3 D4 D5 D6 D7 D8

1 3 ws D1 D2 D3 D4 D5 D6 D7 D8 D9

2 3 ws D2 D3 D4 D5 D6 D7 D8 D9 D10

3 3 ws D3 D4 D5 D6 D7 D8 D9 D10 D11

Word Wait

States Cycle

0 6 ws D0 D1 D2 D3 1 ws D4 D5 D6 D7

1 6 ws D1 D2 D3 1 ws 1 ws D4 D5 D6 D7

2 6 ws D2 D3 1 ws 1 ws 1 ws D4 D5 D6 D7

3 6 ws D3 1 ws 1 ws 1 ws 1 ws D4 D5 D6 D7

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 23

Preliminary

Ta bl e 9 . Address/Boundary Crossing Latency for 5 Wait States (< 68 MHz)

Ta bl e 1 0 . Address/Boundary Crossing Latency for 4 Wait States (< 54 MHz)

Table 11. Address/Boundary Crossing Latency for 3 Wait States (< 40 MHz)

Continuous Burst

The device will continue to output sequential burst data, wrapping around to ad-

dress 000000h after it reaches the highest addressable memory location, until

the system drives CE# high, RESET# low, or AVD# low in conjunction with a new

address. See Ta b l e 1.

If the host system crosses a 128-word line boundary while reading in burst mode,

and the subsequent word line is not programming or erasing, a one-cycle latency

is required as described above if the device is operating above 66 MHz. If the de-

vice is operating at or below 66 MHz, no boundary crossing latency is required. If

the host system crosses the bank boundary while the subsequent bank is pro-

gramming or erasing, the device will provide read status information. The clock

will be ignored. After the host has completed status reads, or the device has com-

pleted the program or erase operation, the host can restart a burst operation

using a new address and AVD# pulse.

8-, 16-, and 32-Word Linear Burst with Wrap Around

The next three burst read modes are of the linear wrap around design, in which

a fixed number of words are read from consecutive addresses. In each of these

modes, the burst addresses read are determined by the group within which the

starting address falls. The groups are sized according to the number of words

read in a single burst sequence for a given mode (see Table 1 2 .)

Word Wait

States Cycle

0 5 ws D0 D1 D2 D3 D4 D5 D6 D7 D8

1 5 ws D1 D2 D3 1 ws D4 D5 D6 D7 D8

2 5 ws D2 D3 1 ws 1 ws D4 D5 D6 D7 D8

3 5 ws D3 1 ws 1 ws 1 ws D4 D5 D6 D7 D8

Word Wait

States Cycle

0 4 ws D0 D1 D2 D3 D4 D5 D6 D7 D8

1 4 ws D1 D2 D3 D4 D5 D6 D7 D8 D9

2 4 ws D2 D3 1 ws D4 D5 D6 D7 D8 D9

3 4 ws D3 1 ws 1 ws D4 D5 D6 D7 D8 D9

Word Wait

States Cycle

0 3 ws D0 D1 D2 D3 D4 D5 D6 D7 D8

1 3 ws D1 D2 D3 D4 D5 D6 D7 D8 D9

2 3 ws D2 D3 D4 D5 D6 D7 D8 D9 D10

3 3 ws D3 1 ws D4 D5 D6 D7 D8 D9 D10

24 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

Ta bl e 1 2 . Burst Address Groups

For example, if the starting address in the 8-word mode is 3Ch, the address range

to be read would be 38-3Fh, and the burst sequence would be 3C-3D-3E-3F-38-

39-3A-3Bh if wrap around is enabled. The burst sequence begins with the starting

address written to the device, but wraps back to the first address in the selected

group and stops at the group size, terminating the burst read. In a similar fash-

ion, the 16-word and 32-word Linear Wrap modes begin their burst sequence on

the starting address written to the device, and then wrap back to the first address

in the selected address group. Note that in these three burst read modes the

address pointer does not cross the boundary that occurs every 128

words; thus, no wait states are inserted (except during the initial ac-

cess). (See Figure 14.)

8-, 16-, and 32-Word Linear Burst without Wrap Around

If wrap around is not enabled, 8-word, 16-word, or 32-word burst will execute

linearly up to the maximum memory address of the selected number of words.

The burst will stop after 8, 16, or 32 addresses and will not wrap around to the

first address of the selected group. For example: if the starting address in the 8-

word mode is 3Ch, the address range to be read would be 39-40h, and the burst

sequence would be 3C-3D-3E-3F-40-41-42-43h if wrap around is not enabled.

The next address to be read will require a new address and AVD# pulse. Note

that in this burst read mode, the address pointer may cross the boundary that

occurs every 128 words.

Configuration Register

The device uses a configuration register to set the various burst parameters:

number of wait states, burst read mode, RDY configuration, and synchronous

mode active. For more information, see Ta b l e 2 7 .

RDY: Ready

The RDY is a dedicated output, controlled by CE#. When the device is configured

in the Synchronous mode and RDY is at logic low, the system should wait 1 clock

cycle before expecting the next word of data.

Handshaking

The device is equipped with a handshaking feature that allows the host system

to simply monitor the RDY signal from the device to determine when the burst

data is ready to be read. The host system should use the programmable wait

state configuration to set the number of wait states for optimal burst mode oper-

ation. The initial word of burst data is indicated by the rising edge of RDY after

OE# goes low.

For optimal burst mode performance, the host system must set the appropriate

number of wait states in the flash device depending on clock frequency. See Set

Configuration Register Command Sequence and Requirements for Synchronous

(Burst) Read Operation for more information.

Mode Group Size

Group Address Ranges

8-word 8 words 0-7h, 8-Fh, 10-17h,...

16-word 16 words 0-Fh, 10-1Fh, 20-2Fh,...

32-word 32 words 00-1Fh, 20-3Fh, 40-5Fh,...

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 25

Preliminary

Simultaneous Read/Write Operations with Zero Latency

This device is capable of reading data from one bank of memory while program-

ming or erasing in another bank of memory. An erase operation may also be

suspended to read from or program to another location within the same bank (ex-

cept the sector being erased). Figure 30 shows how read and write cycles may be

initiated for simultaneous operation with zero latency. Refer to the DC Character-

istics table for read-while-program and read-while-erase current specifications.

Writing Commands/Command Sequences

The device has the capability of performing an asynchronous or synchronous

write operation. While the device is configured in Asynchronous read it is able to

perform Asynchronous write operations only. CLK is ignored when the device is

configured in the Asynchronous mode. When in the Synchronous read mode con-

figuration, the device is able to perform both Asynchronous and Synchronous

write operations. CLK- and AVD#-induced address latches are supported in the

Synchronous programming mode. During a synchronous write operation, to write

a command or command sequence (which includes programming data to the de-

vice and erasing sectors of memory), the system must drive AVD# and CE# to

VIL, and OE# to VIH when providing an address to the device, and drive WE# and

CE# to VIL, and OE# to VIH when writing commands or data. During an asynchro-

nous write operation, the system must drive CE# and WE# to VIL and OE# to VIH

when providing an address, command, and data. Addresses are latched on the

last falling edge of WE# or CE#, while data is latched on the 1st rising edge of

WE# or CE# (see Tab l e 27 ).

An erase operation can erase one sector, multiple sectors, or the entire device.

Tables 21–23 indicate the address space that each sector occupies. The device

address space is divided into sixteen banks: Banks 1 through 14 contain only 64

Kword sectors, while Banks 0 and 15 contain both 16 Kword boot sectors in ad-

dition to 64 Kword sectors. A “bank address” is the set of address bits required

to uniquely select a bank. Similarly, a “sector address” is the address bits re-

quired to uniquely select a sector.

ICC2 in “DC Characteristics” represents the active current specification for the

write mode. “AC Characteristics—Synchronous” and “AC Characteristics—Asyn-

chronous” contain timing specification tables and timing diagrams for write

operations.

Unlock Bypass Mode

The device features an Unlock Bypass mode to facilitate faster programming.

Once the device enters the Unlock Bypass mode, only two write cycles are re-

quired to program a set of words, instead of four. See Unlock Bypass Command

Sequence for more details.

Accelerated Program/Chip Erase Operations

The device offers accelerated chip program and erase operations through the ACC

function. This method is faster than the standard chip program and erase com-

mand sequences. The accelerated chip program and erase functions must

not be used more than 10 times per sector. In addition, accelerated chip pro-

gram and erase should be performed at room temperature (25°C ±10°C).

The system can use the Write Buffer Load command sequence. Note that if a

“Write-to-Buffer-Abort Reset” is required, the full 3-cycle RESET command se-

quence must be used to reset the device. Removing VHH from the ACC input,

upon completion of the embedded program or erase operation, returns the device

26 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

to normal operation. Note that sectors must be unlocked prior to raising ACC to

VHH. Note that the ACC pin must not be at VHH for operations other than acceler-

ated programming and accelerated chip erase, or device damage may result. In

addition, the ACC pin must not be left floating or unconnected; inconsistent be-

havior of the device may result.

When at VIL, ACC locks all sectors. ACC should be at VIH for all other conditions.

Write Buffer Programming Operation

Write Buffer Programming allows the system to write a maximum of 32 words

in one programming operation. This results in a faster effective word program-

ming time than the standard “word” programming algorithms. The Write Buffer

Programming command sequence is initiated by first writing two unlock cycles.

This is followed by a third write cycle containing the Write Buffer Load command

written at the starting address in which programming will occur. At this point, the

system writes the number of “word locations minus 1” that will be loaded into

the page buffer at the starting address in which programming will occur. This tells

the device how many write buffer addresses will be loaded with data and there-

fore when to expect the “Program Buffer to Flash” confirm command. The number

of locations to program cannot exceed the size of the write buffer or the operation

will abort. (NOTE: the number loaded = the number of locations to program

minus 1. For example, if the system will program 6 address locations, then 05h

should be written to the device.)

The system then writes the starting address/data combination. This starting ad-

dress is the first address/data pair to be programmed, and selects the “write-

buffer-page” address. All subsequent address/data pairs must fall within the “se-

lected-write-buffer-page”.

The “write-buffer-page” is selected by using the addresses AMAX - A5 where AMAX

is A23 for WS256N, A22 for WS128N, and A21 for WS064N.

The “write-buffer-page” addresses must be the same for all address/data

pairs loaded into the write buffer. (This means Write Buffer Programming

cannot be performed across multiple “write-buffer-pages”. This also means that

Write Buffer Programming cannot be performed across multiple sectors. If the

system attempts to load programming data outside of the selected “write-buffer-

page”, the operation will ABORT.)

After writing the Starting Address/Data pair, the system then writes the remain-

ing address/data pairs into the write buffer. Write buffer locations may be loaded

in any order.

Note that if a Write Buffer address location is loaded multiple times, the “address/

data pair” counter will be decremented for every data load operation. Also,

the last data loaded at a location before the “Program Buffer to Flash” confirm

command will be programmed into the device. It is the software’s responsibility

to comprehend ramifications of loading a write-buffer location more than once.

The counter decrements for each data load operation, NOT for each unique

write-buffer-address location.

Once the specified number of write buffer locations have been loaded, the system

must then write the “Program Buffer to Flash” command at the Sector Address.

Any other address/data write combinations will abort the Write Buffer Program-

ming operation. The device will then “go busy.” The Data Bar polling techniques

should be used while monitoring the last address location loaded into the

write buffer. This eliminates the need to store an address in memory because

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 27

Preliminary

the system can load the last address location, issue the program confirm com-

mand at the last loaded address location, and then data bar poll at that same

address. DQ7, DQ6, DQ5, DQ2, and DQ1 should be monitored to determine the

device status during Write Buffer Programming.

The write-buffer “embedded” programming operation can be suspended using

the standard suspend/resume commands. Upon successful completion of the

Write Buffer Programming operation, the device will return to READ mode.

The Write Buffer Programming Sequence is ABORTED under any of the following

conditions:

Load a value that is greater than the page buffer size during the “Number of

Locations to Program” step.

Write to an address in a sector different than the one specified during the

“Write-Buffer-Load” command.

Write an Address/Data pair to a different write-buffer-page than the one se-

lected by the “Starting Address” during the “write buffer data loading” stage

of the operation.

Write data other than the “Confirm Command” after the specified number of

“data load” cycles.

The ABORT condition is indicated by DQ1 = 1, DQ7 = DATA# (for the “last ad-

dress location loaded”), DQ6 = TOGGLE, DQ5 = 0. This indicates that the Write

Buffer Programming Operation was ABORTED. A “Write-to-Buffer-Abort reset”

command sequence is required when using the Write-Buffer-Programming fea-

tures in Unlock Bypass mode. Note that the SecSiTM sector, autoselect, and CFI

functions are unavailable when a program operation is in progress.

Use of the write buffer is strongly recommended for programming when

multiple words are to be programmed. Write buffer programming is allowed

in any sequence of memory (or address) locations. These flash devices are capa-

ble of handling multiple write buffer programming operations on the same write

buffer address range without intervening erases. However, programming the

same word address multiple times without intervening erases requires a modified

programming method. Please contact your local SpansionTM representative for

details.

Autoselect Mode

The autoselect mode provides manufacturer and device identification, and sector

protection verification, through identifier codes output from the internal register

(separate from the memory array) on DQ15–DQ0. This mode is primarily in-

tended for programming equipment to automatically match a device to be

programmed with its corresponding programming algorithm. The autoselect

codes can also be accessed in-system.

When verifying sector protection, the sector address must appear on the appro-

priate highest order address bits (see Tables 21–23). The remaining address bits

are don’t care. When all necessary bits have been set as required, the program-

ming equipment may then read the corresponding identifier code on DQ15–DQ0.

The autoselect codes can also be accessed in-system through the command reg-

ister. See Command Definition Summary for command sequence requirements.

Note that if a Bank Address (BA) on the four uppermost address bits is asserted

during the third write cycle of the autoselect command, the host system can read

autoselect data from that bank and then immediately read array data from the

other bank, without exiting the autoselect mode.

28 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

To access the autoselect codes, the host system must issue the autoselect com-

mand via the command register, as shown in the Command Definition Summary

section. See Autoselect Command Sequence for more information.

Advanced Sector Protection and Unprotection

This advanced security feature provides an additional level of protection to all

sectors against inadvertant program or erase operations.

The advanced sector protection feature disables both programming and erase op-

erations in a sector while the advanced sector unprotection feature re-enables

both program and erase operations in previously protected sectors. Sector pro-

tection/unprotection can be implemented using either or both of the two methods

Hardware method

Software method

Persistent/Password Sector Protection is achieved by using the software method

while the sector protection with WP# pin is achieved by using the hardware

method.

All parts default to operate in the Persistent Sector Protection mode. The cus-

tomer must then choose if the Persistent or Password Protection method is most

desirable. There are two one-time programmable non-volatile bits that define

which sector protection method will be used.

Persistent Mode Lock Bit

Password Mode Lock Bit

If the customer decides to continue using the Persistent Sector Protection

method, they must set the Persistent Mode Lock Bit. This will permanently set

the part to operate using only Persistent Sector Protection. However, if the cus-

tomer decides to use the Password Sector Protection method, they must set the

Password Mode Lock Bit. This will permanently set the part to operate using

only Password Sector Protection.

It is important to remember that setting either the Persistent Mode Lock Bit

or the Password Mode Lock Bit permanently selects the protection mode. It is

not possible to switch between the two methods once a locking bit has been set.

It is important that one mode is explicitly selected when the device is

first programmed, rather than relying on the default mode alone. If both

are selected to be set at the same time, the operation will abort. This is

done so that it is not possible for a system program or virus to later set the Pass-

word Mode Locking Bit, which would cause an unexpected shift from the default

Persistent Sector Protection Mode into the Password Sector Protection Mode.

The device is shipped with all sectors unprotected. Optional SpansionTM program-

ming services enable programming and protecting sectors at the factory prior to

shipping the device. Contact your local sales office for more details.

Persistent Mode Lock Bit

A Persistent Mode Lock Bit exists to guarantee that the device remain in software

sector protection. Once programmed (set to “0”), the Persistent Mode Lock Bit

prevents programming of the Password Mode Lock Bit. This allows protection

from potential hackers locking the device by placing the device in password sec-

tor protection mode and then changing the password accordingly.

Password Mode Lock Bit

In order to select the Password Sector Protection scheme, the customer must first

program the password. It is recommended that the password be somehow cor-

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 29

Preliminary

related to the unique Electronic Serial Number (ESN) of the particular flash

device. Each ESN is different for every flash device; therefore each password

should be different for every flash device. While programming in the password

region, the customer may perform Password Verify operations.

Once the desired password is programmed in, the customer must then set the

Password Mode Locking Bit. This operation achieves two objectives:

1.It permanently sets the device to operate using the Password Sector Protection

Mode. It is not possible to reverse this function.

2.It also disables all further commands to the password region. All program and

read operations are ignored.

Both of these objectives are important, and if not carefully considered, may lead

to unrecoverable errors. The user must be sure that the Password Sector Protec-

tion method is desired when setting the Password Mode Locking Bit. More

importantly, the user must be sure that the password is correct when the Pass-

word Mode Locking Bit is set. Due to the fact that read operations are disabled,

there is no means to verify what the password is after it is set. If the password

is lost after setting the Password Mode Lock Bit, there will be no way to clear the

PPB Lock Bit.

The Password Mode Lock Bit, once set, prevents reading the 64-bit password on

the DQ bus and further password programming. The Password Mode Lock Bit

is not erasable. Once the Password Mode Lock Bit is programmed, the Persistent

Mode Lock Bit is disabled from programming, guaranteeing that no changes to

the protection scheme are allowed.

Sector Protection

The device features several levels of sector protection, which can disable both the

program and erase operations in certain sectors.

Persistent Sector Protection

A software enabled command sector protection method that replaces the old 12

V controlled protection method.

Password Sector Protection

A highly sophisticated software enabled protection method that requires a pass-

word before changes to certain sectors or sector groups are permitted

WP# Hardware Protection

A write protect pin (WP#) can prevent program or erase operations in the outer-

most sectors.The WP# Hardware Protection feature is always available,

independent of the software managed protection method chosen.

Persistent Sector Protection

The Persistent Sector Protection method replaces the old 12 V controlled protec-

tion method while at the same time enhancing flexibility by providing three

different sector protection states:

Persistently Locked—A sector is protected and cannot be changed.

Dynamically Locked—The sector is protected and can be changed by a simple

command

Unlocked—The sector is unprotected and can be changed by a simple com-

mand

30 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

In order to achieve these states, three types of “bits” namely Persistent Protec-

tion Bit (PPB), Dynamic Protection Bit (DYB), and Persistent Protection Bit Lock

(PPB Lock) are used to achieve the desired sector protection scheme

Persistent Protection Bit (PPB)

PPB is used to as an advanced security feature to protect individual sectors from

being programmed or erased thereby providing additional level of protection.

Every sector is assigned a Persistent Protection Bit.

Each PPB is individually programmed through the PPB Program Command.

However all PPBs are erased in parallel through the All PPB Erase Command.

Prior to erasing, these bits don’t have to be preprogrammed. The Embedded

Erase algorithm automatically preprograms and verifies prior to an electrical

erase. The system is not required to provide any controls or timings during these

operations.

The PPBs retain their state across power cycles because they are Non-Volatile.

The PPBs have the same endurance as the flash memory.

Persistent Protection Bit Lock (PPB Lock Bit) in Persistent Sector

Protection Mode

PPB Lock Bit is a global volatile bit and provides an additional level of protection

to the sectors. When programmed (set to “0”), all the PPBs are locked and

hence none of them can be changed. When erased (cleared to “1”), the PPBs

are changeable. There is only one PPB Lock Bit in every device. Only a hardware

reset or a power-up clears the PPB Lock Bit. Note that there is no software solu-

tion; that is, there is no command sequence that would unlock the PPB Lock Bit.

Once all PPBs are configured to the desired settings, the PPB Lock Bit may be set

(programmed to “0”). The PPB Lock Bit is set by issuing the PPB Lock Bit Set Com-

mand. Programming or setting the PPB Lock Bit disables program and erase

commands to all the PPBs. In effect, the PPB Lock Bit locks the PPBs into their

current state. The only way to clear the PPB Lock Bit is to go through a hardware

or power-up reset. System boot code can determine if any changes to the PPB

are needed e.g. to allow new system code to be downloaded. If no changes are

needed then the boot code can disable the PPB Lock Bit to prevent any further

changes to the PPBs during system operation.

Dynamic Protection Bit (DYB)

DYB is another security feature used to protect individual sectors from being pro-

grammed or erased inadvertently. It is a volatile protection bit and is assigned to

each sector. Each DYB can be individually modified through the DYB Set Com-

mand or the DYB Clear Command.

The Protection Status for a particular sector is determined by the status of the

PPB and the DYB relative to that sector. For the sectors that have the PPBs cleared

(erased to “1”), the DYBs control whether or not the sector is protected or unpro-

tected. By issuing the DYB Set or Clear command sequences, the DYBs will be set

(programmed to “0”) or cleared (erased to “1”), thus placing each sector in the

protected or unprotected state respectively. These states are the so-called Dy-

namic Locked or Unlocked states due to the fact that they can switch back and

forth between the protected and unprotected states. This feature allows software

to easily protect sectors against inadvertent changes yet does not prevent the

easy removal of protection when changes are needed. The DYBs maybe set (pro-

grammed to “0”) or cleared (erased to “1”) as often as needed.

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 31

Preliminary

When the parts are first shipped, the PPBs are cleared (erased to “1”) and upon

power up or reset, the DYBs are set or cleared depending upon the ordering op-

tion chosen. If the option to clear the DYBs after power up is chosen, (erased to

“1”), then the sectors may be modified depending upon the PPB state of that sec-

tor. (See Ta b l e 13 ) If the option to set the DYBs after power up is chosen

(programmed to “0”), then the sectors would be in the protected state. The PPB

Lock Bit defaults to the cleared state (erased to “1”) after power up and the PPBs

retain their previous state as they are non-volatile.

It is possible to have sectors that have been persistently locked, and sectors that

are left in the dynamic state. The sectors in the dynamic state are all unprotected.

If there is a need to protect some of them, a simple DYB Set command sequence

is all that is necessary. The DYB Set or Clear command for the dynamic sectors

signify protected or unprotected state of the sectors respectively. However, if

there is a need to change the status of the persistently locked sectors, a few more

steps are required. First, the PPB Lock Bit must be cleared by either putting the

device through a power-cycle, or hardware reset. The PPBs can then be changed

to reflect the desired settings. Setting the PPB Lock Bit once again will lock the

PPBs, and the device operates normally again.

To achieve the best protection, execute the PPB Lock Bit Set command early in

the boot code and protect the boot code by holding WP# = VIL. Note that the PPB

and DYB bits have the same function when ACC = VHH as they do when ACC =

VIH.

Ta bl e 1 3. Sector Protection Schemes

Tab l e 1 3 contains all possible combinations of the DYB, PPB, and PPB Lock relating

to the status of the sector.

In summary, if the PPB is set (programmed to “0”), and the PPB Lock is set (pro-

grammed to “0”), the sector is protected and the protection can not be removed

until the next power cycle clears (erase to “1”) the PPB Lock Bit. Once the PPB

Lock Bit is cleared (erased to “1”), the sector can be persistently locked or un-

locked. Likewise, if both PPB Lock Bit or PPB is cleared (erased to “1”) the sector

can then be dynamically locked or unlocked. The DYB then controls whether or

not the sector is protected or unprotected.

If the user attempts to program or erase a protected sector, the device ignores

the command and returns to read mode. A program or erase command to a pro-

DYB PPB PPB Lock Sector State

1 1 1 Sector Unprotected

0 1 1 Sector Protected through DYB

1 0 1 Sector Protected through PPB

0 0 1 Sector Protected through PPB

and DYB

1 1 0 Sector Unprotected

0 1 0 Sector Protected through DYB

1 0 0 Sector Protected through PPB

0 0 0 Sector Protected through PPB

and DYB

32 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

tected sector enables status polling and returns to read mode without having

modified the contents of the protected sector.

The programming of the DYB, PPB, and PPB Lock for a given sector can be verified

by writing individual status read commands DYB Status, PPB Status, and PPB

Lock Status to the device.

Password Sector Protection

The Password Sector Protection Mode method allows an even higher level of se-

curity than the Persistent Sector Protection Mode. There are two main differences

between the Persistent Sector Protection Mode and the Password Sector Protec-

tion Mode:

When the device is first powered up, or comes out of a reset cycle, the PPB

Lock Bit is set to the locked state, rather than cleared to the unlocked

state.

The only means to clear the PPB Lock Bit is by writing a unique 64-bit Pass-

word to the device.

The Password Sector Protection method is otherwise identical to the Persistent

Sector Protection method.

A 64-bit password is the only additional tool utilized in this method.

The password is stored in a non-erasable region of the flash memory. Once the

Password Mode Lock Bit is set, the password is permanently set with no means

to read, program, or erase it. The password is used to clear the PPB Lock Bit. The

Password Unlock command must be written to the flash, along with a password.

The flash device internally compares the given password with the pre-pro-

grammed password. If they match, the PPB Lock Bit is cleared, and the PPBs can

be altered. If they do not match, the flash device does nothing. There is a built-

in 1 µs delay for each “password check.” This delay is intended to thwart any ef-

forts to run a program that tries all possible combinations in order to crack the

password.

64-bit Password

The 64-bit Password is located in its own memory space and is accessible through

the use of the Password Program and Verify commands. The password function

works in conjunction with the Password Mode Locking Bit, which when set, pre-

vents the Password Verify command from reading the contents of the password

on the pins of the device.

Persistent Protection Bit Lock (PPB Lock Bit) in Password Sector

Protection Mode

The Persistent Protection Bit Lock (PPB Lock Bit) is a volatile bit that reflects the

state of the Password Mode Lock Bit after power-up reset. If the Password Mode

Lock Bit is also set, after a hardware reset (RESET# asserted) or a power-up re-

set, the ONLY means for clearing the PPB Lock Bit in Password Protection Mode is

to issue the Password Unlock command. Successful execution of the Password

Unlock command to enter the entire password clears the PPB Lock Bit, allowing

for sector PPBs modifications. Asserting RESET# or taking the device through a

power-on reset, resets the PPB Lock Bit to a “1”.

If the Password Mode Lock Bit is not set (device is operating in the default Per-

sistent Protection Mode). The Password Unlock command is ignored in Persistent

Sector Protection Mode.

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 33

Preliminary

Lock Register

The Lock Register consists of 3 bits. The Customer SecSi Sector Protection Bit is

DQ0, Persistent Protection Mode Lock Bit is DQ1, and the Password Protection

Mode Lock Bit is DQ2. Each of these bits are non-volatile. DQ15-DQ3 are reserved

and will be 1’s.

Ta bl e 1 4 . WS256N Lock Register

Ta bl e 1 5. WS128N/064N Lock Register

Hardware Data Protection Mode

The device offers two types of data protection at the sector level:

When WP# is at VIL, the four outermost sectors are locked (device specific).

When ACC is at VIL, all sectors are locked.

The write protect pin (WP#) adds a final level of hardware program and erase

protection to the outermost boot sectors. The outermost boot sectors are the sec-

tors containing both the lower and upper set of outermost sectors in a dual-boot-

configured device. When this pin is low it is not possible to change the con-

tents of these outermost sectors. These sectors generally hold system boot

code. So, the WP# pin can prevent any changes to the boot code that could over-

ride the choices made while setting up sector protection during system

initialization.

The following hardware data protection measures prevent accidental erasure or

programming, which might otherwise be caused by spurious system level signals

during VCC power-up and power-down transitions, or from system noise.

Write Protect (WP#)

The Write Protect feature provides a hardware method of protecting the four out-

ermost sectors. This function is provided by the WP# pin and overrides the

previously discussed Sector Protection/Unprotection method.

If the system asserts VIL on the WP# pin during the command sequence, the de-

vice disables program and erase functions in the “outermost” boot sectors. The

outermost boot sectors are the sectors containing both the lower and upper set

of sectors in a dual-boot-configured device.

If the system asserts VIH on the WP# pin, the device reverts to whether the boot

sectors were last set to be protected or unprotected after the embedded opera-

tion. That is, sector protection or unprotection for these sectors depends on

whether they were last protected or unprotected.

DQ15-3 DQ2 DQ1 DQ0

1’s Password Protection Mode

Lock Bit

Persistent Protection Mode

Lock Bit

Customer SecSi Sector

Protection Bit

DQ15-5 DQ4 DQ3 DQ2 DQ1 DQ0

Undefined

DYB Lock Boot Bit

0 = DYB bits, power up

protected

1 = DYB bits, power up

unprotected

PPB One-Time Programmable Bit

0 = All PPB erase command

disabled

1 = All PPB Erase command

enabled

Password

Protection

Mode Lock

Bit

Persistent

Protection

Mode Lock

Bit

SecSi Sector

Protection Bit

34 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

Note that the WP# pin must not be left floating or unconnected; inconsistent be-

havior of the device may result. The WP# pin must be held stable during a

command sequence.

Low VCC Write Inhibit

When VCC is less than VLKO, the device does not accept any write cycles. This pro-

tects data during VCC power-up and power-down. The command register and all

internal program/erase circuits are disabled, and the device resets to reading

array data. Subsequent writes are ignored until VCC is greater than VLKO. The sys-

tem must provide the proper signals to the control inputs to prevent unintentional

writes when VCC is greater than VLKO.

Write Pulse “Glitch” Protection

Noise pulses of less than tWEP on WE# do not initiate a write cycle.

Logical Inhibit

Write cycles are inhibited by holding any one of OE# = VIL, CE# = VIH or WE# =

VIH. To initiate a write cycle, CE# and WE# must be a logical zero while OE# is a

logical one.

Power-Up Write Inhibit

If WE# = CE# = RESET# = VIL and OE# = VIH during power up, the device does

not accept commands on the rising edge of WE#. The internal state machine is

automatically reset to the read mode on power-up

Standby Mode

When the system is not reading or writing to the device, it can place the device

in the standby mode. In this mode, current consumption is greatly reduced, and

the outputs are placed in the high impedance state, independent of the OE#

input.

The device enters the standby mode when the CE# and RESET# inputs are both

held at VCC. The device requires standard access time (tCE) for read access, be-

fore it is ready to read data.

If the device is deselected during erasure or programming, the device draws ac-

tive current until the operation is completed.

ICC3 in “DC Characteristics” represents the standby current specification.

Automatic Sleep Mode

The automatic sleep mode minimizes Flash device energy consumption. While in

asynchronous mode, the device automatically enables this mode when addresses

remain stable for tACC + 20 ns. The automatic sleep mode is independent of the

CE#, WE#, and OE# control signals. Standard address access timings provide

new data when addresses are changed. While in sleep mode, output data is

latched and always available to the system. While in synchronous mode, the au-

tomatic sleep mode is disabled. Note that a new burst operation is required to

provide new data.

ICC6 in “DC Characteristics” represents the automatic sleep mode current

specification.

RESET#: Hardware Reset Input

The RESET# input provides a hardware method of resetting the device to reading

array data. When RESET# is driven low for at least a period of tRP

, the device im-

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 35

Preliminary

mediately terminates any operation in progress, tristates all outputs, resets the

configuration register, and ignores all read/write commands for the duration of

the RESET# pulse. The device also resets the internal state machine to reading

array data. The operation that was interrupted should be reinitiated once the de-

vice is ready to accept another command sequence, to ensure data integrity.

Current is reduced for the duration of the RESET# pulse. When RESET# is held

at VSS, the device draws CMOS standby current (ICC4). If RESET# is held at VIL,

but not at VSS, the standby current will be greater.

RESET# may be tied to the system reset circuitry. A system reset would thus also

reset the Flash memory, enabling the system to read the boot-up firmware from

the Flash memory.

See Hardware Reset (RESET#) for RESET# parameters and to Figure 19 for the

timing diagram.

Output Disable Mode

When the OE# input is at VIH, output from the device is disabled. The outputs are

placed in the high impedance state.

SecSi™ (Secured Silicon) Sector Flash Memory Region

The SecSi (Secured Silicon) Sector feature provides an extra Flash memory re-

gion that enables permanent part identification through an Electronic Serial

Number (ESN). The SecSi Sector is 256 words in length. All reads outside of the

256 word address range will return non-valid data. The Factory Indicator Bit,

DQ7, (at Autoselect address (BAS) + 03h) is used to indicate whether or not the

Factory SecSi Sector is locked when shipped from the factory. The Customer In-

dicator Bit (DQ6) is used to indicate whether or not the Customer SecSi Sector is

locked when shipped from the factory. The Factory SecSi bits are permanently set

at the factory and cannot be changed, which prevents cloning of a factory locked

part. This ensures the security of the ESN and customer code once the product is

shipped to the field.

The Factory portion of the SecSi Sector is locked when shipped and the Customer

SecSi Sector that is either locked or is lockable. The Factory SecSi Sector is al-

ways protected when shipped from the factory, and has the Factory Indicator Bit

(DQ7) permanently set to a “1”. The Customer SecSi Sector is typically shipped

unprotected (set to “0”), allowing customers to utilize that sector in any manner

they choose. Once the Customer SecSi Sector area is protected, the Customer

Indicator Bit will be permanently set to “1.”

The system accesses the SecSi Sector through a command sequence (see Enter

SecSi™ Sector/Exit SecSi Sector Command Sequence). After the system has

written the Enter SecSi Sector command sequence, it may read the SecSi Sector

by using the addresses normally occupied by sector SA0 within the memory ar-

ray. This mode of operation continues until the system issues the Exit SecSi

Sector command sequence, or until power is removed from the device. While

SecSi Sector access is enabled, Memory Array read access, program operations,

and erase operations to all sectors other than SA0 are also available. On power-

up, or following a hardware reset, the device reverts to sending commands to the

normal address space.

36 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

Factory Locked: Factor SecSi Sector Programmed and Protected

At the Factory

In a factory sector locked device, the Factory SecSi Sector is protected when the

device is shipped from the factory. The Factory SecSi Sector cannot be modified

in any way. The device is pre programmed with both a random number and a se-

cure ESN. The Factory SecSi Sector is located at addresses 000000h–00007Fh.

The device is available pre programmed with one of the following:

A random, secure ESN only within the Factor SecSi Sector

Customer code within the Customer SecSi Sector through the SpansionTM pro-

gramming service

Both a random, secure ESN and customer code through the SpansionTM pro-

gramming service.

Ta bl e 1 6. SecSiTM Sector Addresses

Customers may opt to have their code programmed through the SpansionTM pro-

gramming services. Spansion programs the customer’s code, with or without the

random ESN. The devices are then shipped from the Spansion factory with the

Factory SecSi Sector and Customer SecSi Sector permanently locked. Contact

your local representative for details on using SpansionTM programming services.

Customer SecSi Sector

If the security feature is not required, the Customer SecSi Sector can be treated

as an additional Flash memory space. The Customer SecSi Sector can be read

any number of times, but can be programmed and locked only once. Note that

the accelerated programming (ACC) and unlock bypass functions are not avail-

able when programming the Customer SecSi Sector, but reading in Banks 1

through 15 is available. The Customer SecSi Sector is located at addresses

000080h–0000FFh.

The Customer SecSi Sector area can be protected by writing the SecSi Sector

Protection Bit Lock command sequence.

Once the Customer SecSi Sector is locked and verified, the system must write the

Exit SecSi Sector Region command sequence to return to reading and writing the

memory array. The device returns to the memory array at sector 0.

The Customer SecSi Sector lock must be used with caution since, once locked,

there is no procedure available for unlocking the Customer SecSi Sector area and

none of the bits in the Customer SecSi Sector memory space can be modified in

any way.

Common Flash Memory Interface (CFI)

The Common Flash Interface (CFI) specification outlines device and host system

software interrogation handshake, which allows specific vendor-specified soft-

ware algorithms to be used for entire families of devices. Software support can

then be device-independent, JEDEC ID-independent, and forward- and back-

ward-compatible for the specified flash device families. Flash vendors can

standardize their existing interfaces for long-term compatibility.

This device enters the CFI Query mode when the system writes the CFI Query

command, 98h, to address (BA)555h any time the device is ready to read array

Sector Sector Size Address Range

Customer 128 words 000080h-0000FFh

Factory 128 words 000000h-00007Fh

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 37

Preliminary

data. The system can read CFI information at valid addresses within that bank

(see Tables 17– 20). All reads outside of the CFI address range, within the bank,

will return non-valid data. Reads from other banks are allowed, writes are not. To

terminate reading CFI data, the system must write the reset command.

For further information, please refer to the CFI Specification and CFI Publication

100. Please contact your sales office for copies of these documents.

38 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

Ta bl e 1 7. CFI Query Identification String

Addresses Data Description

10h

11h

12h

0051h

0052h

0059h

Query Unique ASCII string “QRY”

13h

14h

0002h

0000h

Primary OEM Command Set

15h

16h

0040h

0000h

Address for Primary Extended Table

17h

18h

0000h

Alternate OEM Command Set (00h = none exists)

19h

1Ah

0000h

Address for Alternate OEM Extended Table (00h = none exists)

Ta b le 1 8 . System Interface String

Addresses Data Description

1Bh 0017h

Min. (write/erase)

D7–D4: volt, D3–D0: 100 millivolt

1Ch 0019h

Max. (write/erase)

D7–D4: volt, D3–D0: 100 millivolt

1Dh 0000h

Min. voltage (00h = no V

pin present)

1Eh 0000h

Max. voltage (00h = no V

pin present)

1Fh 0006h

Typical timeout per single byte/word write 2

µs

20h 0009h

Typical timeout for Min. size buffer write 2

µs (00h = not supported)

21h 000Ah

Typical timeout per individual block erase 2

22h 0000h

Typical timeout for full chip erase 2

ms (00h = not supported)

23h 0004h

Max. timeout for byte/word write 2

times typical

24h 0004h

Max. timeout for buffer write 2

times typical

25h 0003h

Max. timeout per individual block erase 2

times typical

26h 0000h

Max. timeout for full chip erase 2

times typical (00h = not supported)

Table 19. Device Geometry Definition

Addresses Data Description

27h

0019h (WS256N)

0018h (WS128N)

0017h (WS064N)

Device Size = 2

byte

28h

29h

0001h

0000h

Flash Device Interface description (refer to CFI publication 100)

2Ah

2Bh

0006h

0000h

Max. number of bytes in multi-byte write = 2

(00h = not supported)

2Ch 0003h

Number of Erase Block Regions within device

2Dh

2Eh

2Fh

30h

0003h

0000h

0080h

0000h

Erase Block Region 1 Information

(refer to the CFI specification or CFI publication 100)

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 39

Preliminary

31h

00FDh (WS256N)

007Dh (WS128N)

003Dh (WS064N)

Erase Block Region 2 Information

32h

33h

34h

0000h

0002h

35h

36h

37h

38h

0003h

0000h

0080h

0000h

Erase Block Region 3 Information

39h

3Ah

3Bh

3Ch

0000h

Erase Block Region 4 Information

Table 20. Primary Vendor-Specific Extended Query

Addresses Data Description

40h

41h

42h

0050h

0052h

0049h

Query-unique ASCII string “PRI”

43h 0031h

Major version number, ASCII

44h 0034h

Minor version number, ASCII

45h 0100h

Address Sensitive Unlock (Bits 1-0)

0 = Required, 1 = Not Required

Silicon Technology (Bits 5-2) 0100 = 0.11 µm

46h 0002h

Erase Suspend

0 = Not Supported, 1 = To Read Only, 2 = To Read & Write

47h 0001h

Sector Protect

0 = Not Supported, X = Number of sectors in per group

48h 0000h

Sector Temporary Unprotect

00 = Not Supported, 01 = Supported

49h 0008h

Sector Protect/Unprotect scheme

08 = Advanced Sector Protection

4Ah

00DFh (WS256N)

006Fh (WS128N)

0037h (WS064N)

Simultaneous Operation

Number of Sectors in all banks except boot bank

4Bh 0001h

Burst Mode Type

00 = Not Supported, 01 = Supported

4Ch 0000h

Page Mode Type

00 = Not Supported, 01 = 4 Word Page, 02 = 8 Word Page, 04 = 16 Word Page

4Dh 0085h

ACC (Acceleration) Supply Minimum

00h = Not Supported, D7-D4: Volt, D3-D0: 100 mV

4Eh 0095h

ACC (Acceleration) Supply Maximum

00h = Not Supported, D7-D4: Volt, D3-D0: 100 mV

4Fh 0001h

Top/Bottom Boot Sector Flag

0001h = Dual Boot Device

Table 19. Device Geometry Definition (Continued)

Addresses Data Description

40 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

50h 0001h

Program Suspend. 00h = not supported

51h 0001h

Unlock Bypass

00 = Not Supported, 01=Supported

52h 0007h

SecSi Sector (Customer OTP Area) Size 2

bytes

53h 0014h

Hardware Reset Low Time-out during an embedded algorithm to read mode

Maximum 2

54h 0014h

Hardware Reset Low Time-out not during an embedded algorithm to read mode

Maximum 2

55h 0005h

Erase Suspend Time-out Maximum 2

56h 0005h

Program Suspend Time-out Maximum 2

57h 0010h

Bank Organization: X = Number of banks

58h

0013h (WS256N)

000Bh (WS128N)

0007h (WS064N)

Bank 0 Region Information. X = Number of sectors in bank

59h

0010h (WS256N)

0008h (WS128N)

0004h (WS064N)

Bank 1 Region Information. X = Number of sectors in bank

5Ah

0010h (WS256N)

0008h (WS128N)

0004h (WS064N)

Bank 2 Region Information. X = Number of sectors in bank

5Bh

0010h (WS256N)

0008h (WS128N)

0004h (WS064N)

Bank 3 Region Information. X = Number of sectors in bank

5Ch

0010h (WS256N)

0008h (WS128N)

0004h (WS064N)

Bank 4 Region Information. X = Number of sectors in bank

5Dh

0010h (WS256N)

0008h (WS128N)

0004h (WS064N)

Bank 5 Region Information. X = Number of sectors in bank

5Eh

0010h (WS256N)

0008h (WS128N)

0004h (WS064N)

Bank 6 Region Information. X = Number of sectors in bank

5Fh

0010h (WS256N)

0008h (WS128N)

0004h (WS064N)

Bank 7 Region Information. X = Number of sectors in bank

60h

0010h (WS256N)

0008h (WS128N)

0004h (WS064N)

Bank 8 Region Information. X = Number of sectors in bank

61h

0010h (WS256N)

0008h (WS128N)

0004h (WS064N)

Bank 9 Region Information. X = Number of sectors in bank

62h

0010h (WS256N)

0008h (WS128N)

0004h (WS064N)

Bank 10 Region Information. X = Number of sectors in bank

63h

0010h (WS256N)

0008h (WS128N)

0004h (WS064N)

Bank 11 Region Information. X = Number of sectors in bank

Table 20. Primary Vendor-Specific Extended Query (Continued)

Addresses Data Description

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 41

Preliminary

64h

0010h (WS256N)

0008h (WS128N)

0004h (WS064N)

Bank 12 Region Information. X = Number of sectors in bank

65h

0010h (WS256N)

0008h (WS128N)

0004h (WS064N)

Bank 13 Region Information. X = Number of sectors in bank

66h

0010h (WS256N)

0008h (WS128N)

0004h (WS064N)

Bank 14 Region Information. X = Number of sectors in bank

67h

0013h (WS256N)

000Bh (WS128N)

0007h (WS064N)

Bank 15 Region Information. X = Number of sectors in bank

Table 21. WS256N Sector & Memory Address Map

Bank

Sector Sector Size A23–A14 (x16) Address Range

Bank 0

SA0 16 Kwords 0000000000 000000h-003FFFh

SA1 16 Kwords 0000000001 004000h-007FFFh

SA2 16 Kwords 0000000010 008000h-00BFFFh

SA3 16 Kwords 0000000011 00C000h-00FFFFh

SA4 64 Kwords 00000001XX 010000h-01FFFFh

SA5 64 Kwords 00000010XX 020000h-02FFFFh

SA6 64 Kwords 00000011XX 030000h-03FFFFh

SA7 64 Kwords 00000100XX 040000h-04FFFFh

SA8 64 Kwords 00000101XX 050000h-05FFFFh

SA9 64 Kwords 00000110XX 060000h-06FFFFh

SA10 64 Kwords 00000111XX 070000h-07FFFFh

SA11 64 Kwords 00001000XX 080000h-08FFFFh

SA12 64 Kwords 00001001XX 090000h-09FFFFh

SA13 64 Kwords 00001010XX 0A0000h-0AFFFFh

SA14 64 Kwords 00001011XX 0B0000h-0BFFFFh

SA15 64 Kwords 00001100XX 0C0000h-0CFFFFh

SA16 64 Kwords 00001101XX 0D0000h-0DFFFFh

SA17 64 Kwords 00001110XX 0E0000h-0EFFFFh

SA18 64 Kwords 00001111XX 0F0000h-0FFFFFh

Table 20. Primary Vendor-Specific Extended Query (Continued)

Addresses Data Description

42 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

Bank 1

SA19 64 Kwords 00010000XX 100000h-10FFFFh

SA20 64 Kwords 00010001XX 110000h-11FFFFh

SA21 64 Kwords 00010010XX 120000h-12FFFFh

SA22 64 Kwords 00010011XX 130000h-13FFFFh

SA23 64 Kwords 00010100XX 140000h-14FFFFh

SA24 64 Kwords 00010101XX 150000h-15FFFFh

SA25 64 Kwords 00010110XX 160000h-16FFFFh

SA26 64 Kwords 00010111XX 170000h-17FFFFh

SA27 64 Kwords 00011000XX 180000h-18FFFFh

SA28 64 Kwords 00011001XX 190000h-19FFFFh

SA29 64 Kwords 00011010XX 1A0000h-1AFFFFh

SA30 64 Kwords 00011011XX 1B0000h-1BFFFFh

SA31 64 Kwords 00011100XX 1C0000h-1CFFFFh

SA32 64 Kwords 00011101XX 1D0000h-1DFFFFh

SA33 64 Kwords 00011110XX 1E0000h-1EFFFFh

SA34 64 Kwords 00011111XX 1F0000h-1FFFFFh

Bank 2

SA35 64 Kwords 00100000XX 200000h-20FFFFh

SA36 64 Kwords 00100001XX 210000h-21FFFFh

SA37 64 Kwords 00100010XX 220000h-22FFFFh

SA38 64 Kwords 00100011XX 230000h-23FFFFh

SA39 64 Kwords 00100100XX 240000h-24FFFFh

SA40 64 Kwords 00100101XX 250000h-25FFFFh

SA41 64 Kwords 00100110XX 260000h-26FFFFh

SA42 64 Kwords 00100111XX 270000h-27FFFFh

SA43 64 Kwords 00101000XX 280000h-28FFFFh

SA44 64 Kwords 00101001XX 290000h-29FFFFh

SA45 64 Kwords 00101010XX 2A0000h-2AFFFFh

SA46 64 Kwords 00101011XX 2B0000h-2BFFFFh

SA47 64 Kwords 00101100XX 2C0000h-2CFFFFh

SA48 64 Kwords 00101101XX 2D0000h-2DFFFFh

SA49 64 Kwords 00101110XX 2E0000h-2EFFFFh

SA50 64 Kwords 00101111XX 2F0000h-2FFFFFh

Table 21. WS256N Sector & Memory Address Map (Continued)

Bank

Sector Sector Size A23–A14 (x16) Address Range

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 43

Preliminary

Bank 3

SA51 64 Kwords 00110000XX 300000h-30FFFFh

SA52 64 Kwords 00110001XX 310000h-31FFFFh

SA53 64 Kwords 00110010XX 320000h-32FFFFh

SA54 64 Kwords 00110011XX 330000h-33FFFFh

SA55 64 Kwords 00110100XX 340000h-34FFFFh

SA56 64 Kwords 00110101XX 350000h-35FFFFh

SA57 64 Kwords 00110110XX 360000h-36FFFFh

SA58 64 Kwords 00110111XX 370000h-37FFFFh

SA59 64 Kwords 00111000XX 380000h-38FFFFh

SA60 64 Kwords 00111001XX 390000h-39FFFFh

SA61 64 Kwords 00111010XX 3A0000h-3AFFFFh

SA62 64 Kwords 00111011XX 3B0000h-3BFFFFh

SA63 64 Kwords 00111100XX 3C0000h-3CFFFFh

SA64 64 Kwords 00111101XX 3D0000h-3DFFFFh

SA65 64 Kwords 00111110XX 3E0000h-3EFFFFh

SA66 64 Kwords 00111111XX 3F0000h-3FFFFFh

Bank 4

SA67 64 Kwords 01000000XX 400000h-40FFFFh

SA68 64 Kwords 01000001XX 410000h-41FFFFh

SA69 64 Kwords 01000010XX 420000h-42FFFFh

SA70 64 Kwords 01000011XX 430000h-43FFFFh

SA71 64 Kwords 01000100XX 440000h-44FFFFh

SA72 64 Kwords 01000101XX 450000h-45FFFFh

SA73 64 Kwords 01000110XX 460000h-46FFFFh

SA74 64 Kwords 01000111XX 470000h-47FFFFh

SA75 64 Kwords 01001000XX 480000h-48FFFFh

SA76 64 Kwords 01001001XX 490000h-49FFFFh

SA77 64 Kwords 01001010XX 4A0000h-4AFFFFh

SA78 64 Kwords 01001011XX 4B0000h-4BFFFFh

SA79 64 Kwords 01001100XX 4C0000h-4CFFFFh

SA80 64 Kwords 01001101XX 4D0000h-4DFFFFh

SA81 64 Kwords 01001110XX 4E0000h-4EFFFFh

SA82 64 Kwords 01001111XX 4F0000h-4FFFFFh

Table 21. WS256N Sector & Memory Address Map (Continued)

Bank

Sector Sector Size A23–A14 (x16) Address Range

44 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

Bank 5

SA83 64 Kwords 01010000XX 500000h-50FFFFh

SA84 64 Kwords 01010001XX 510000h-51FFFFh

SA85 64 Kwords 01010010XX 520000h-52FFFFh

SA86 64 Kwords 01010011XX 530000h-53FFFFh

SA87 64 Kwords 01010100XX 540000h-54FFFFh

SA88 64 Kwords 01010101XX 550000h-55FFFFh

SA89 64 Kwords 01010110XX 560000h-56FFFFh

SA90 64 Kwords 01010111XX 570000h-57FFFFh

SA91 64 Kwords 01011000XX 580000h-58FFFFh

SA92 64 Kwords 01011001XX 590000h-59FFFFh

SA93 64 Kwords 01011010XX 5A0000h-5AFFFFh

SA94 64 Kwords 01011011XX 5B0000h-5BFFFFh

SA95 64 Kwords 01011100XX 5C0000h-5CFFFFh

SA96 64 Kwords 01011101XX 5D0000h-5DFFFFh

SA97 64 Kwords 01011110XX 5E0000h-5EFFFFh

SA98 64 Kwords 01011111XX 5F0000h-5FFFFFh

Bank 6

SA99 64 Kwords 01100000XX 600000h-60FFFFh

SA100 64 Kwords 01100001XX 610000h-61FFFFh

SA101 64 Kwords 01100010XX 620000h-62FFFFh

SA102 64 Kwords 01100011XX 630000h-63FFFFh

SA103 64 Kwords 01100100XX 640000h-64FFFFh

SA104 64 Kwords 01100101XX 650000h-65FFFFh

SA105 64 Kwords 01100110XX 660000h-66FFFFh

SA106 64 Kwords 01100111XX 670000h-67FFFFh

SA107 64 Kwords 01101000XX 680000h-68FFFFh

SA108 64 Kwords 01101001XX 690000h-69FFFFh

SA109 64 Kwords 01101010XX 6A0000h-6AFFFFh

SA110 64 Kwords 01101011XX 6B0000h-6BFFFFh

SA111 64 Kwords 01101100XX 6C0000h-6CFFFFh

SA112 64 Kwords 01101101XX 6D0000h-6DFFFFh

SA113 64 Kwords 01101110XX 6E0000h-6EFFFFh

SA114 64 Kwords 01101111XX 6F0000h-6FFFFFh

Table 21. WS256N Sector & Memory Address Map (Continued)

Bank

Sector Sector Size A23–A14 (x16) Address Range

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 45

Preliminary

Bank 7

SA115 64 Kwords 01110000XX 700000h-70FFFFh

SA116 64 Kwords 01110001XX 710000h-71FFFFh

SA117 64 Kwords 01110010XX 720000h-72FFFFh

SA118 64 Kwords 01110011XX 730000h-73FFFFh

SA119 64 Kwords 01110100XX 740000h-74FFFFh

SA120 64 Kwords 01110101XX 750000h-75FFFFh

SA121 64 Kwords 01110110XX 760000h-76FFFFh

SA122 64 Kwords 01110111XX 770000h-77FFFFh

SA123 64 Kwords 01111000XX 780000h-78FFFFh

SA124 64 Kwords 01111001XX 790000h-79FFFFh

SA125 64 Kwords 01111010XX 7A0000h-7AFFFFh

SA126 64 Kwords 01111011XX 7B0000h-7BFFFFh

SA127 64 Kwords 01111100XX 7C0000h-7CFFFFh

SA128 64 Kwords 01111101XX 7D0000h-7DFFFFh

SA129 64 Kwords 01111110XX 7E0000h-7EFFFFh

SA130 64 Kwords 01111111XX 7F0000h-7FFFFFh

Bank 8

SA131 64 Kwords 10000000XX 800000h-80FFFFh

SA132 64 Kwords 10000001XX 810000h-81FFFFh

SA133 64 Kwords 10000010XX 820000h-82FFFFh

SA134 64 Kwords 10000011XX 830000h-83FFFFh

SA135 64 Kwords 10000100XX 840000h-84FFFFh

SA136 64 Kwords 10000101XX 850000h-85FFFFh

SA137 64 Kwords 10000110XX 860000h-86FFFFh

SA138 64 Kwords 10000111XX 870000h-87FFFFh

SA139 64 Kwords 10001000XX 880000h-88FFFFh

SA140 64 Kwords 10001001XX 890000h-89FFFFh

SA141 64 Kwords 10001010XX 8A0000h-8AFFFFh

SA142 64 Kwords 10001011XX 8B0000h-8BFFFFh

SA143 64 Kwords 10001100XX 8C0000h-8CFFFFh

SA144 64 Kwords 10001101XX 8D0000h-8DFFFFh

SA145 64 Kwords 10001110XX 8E0000h-8EFFFFh

SA146 64 Kwords 10001111XX 8F0000h-8FFFFFh

Table 21. WS256N Sector & Memory Address Map (Continued)

Bank

Sector Sector Size A23–A14 (x16) Address Range

46 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

Bank 9

SA147 64 Kwords 10010000XX 900000h-90FFFFh

SA148 64 Kwords 10010001XX 910000h-91FFFFh

SA149 64 Kwords 10010010XX 920000h-92FFFFh

SA150 64 Kwords 10010011XX 930000h-93FFFFh

SA151 64 Kwords 10010100XX 940000h-94FFFFh

SA152 64 Kwords 10010101XX 950000h-95FFFFh

SA153 64 Kwords 10010110XX 960000h-96FFFFh

SA154 64 Kwords 10010111XX 970000h-97FFFFh

SA155 64 Kwords 10011000XX 980000h-98FFFFh

SA156 64 Kwords 10011001XX 990000h-99FFFFh

SA157 64 Kwords 10011010XX 9A0000h-9AFFFFh

SA158 64 Kwords 10011011XX 9B0000h-9BFFFFh

SA159 64 Kwords 10011100XX 9C0000h-9CFFFFh

SA160 64 Kwords 10011101XX 9D0000h-9DFFFFh

SA161 64 Kwords 10011110XX 9E0000h-9EFFFFh

SA162 64 Kwords 10011111XX 9F0000h-9FFFFFh

Bank 10

SA163 64 Kwords 10100000XX A00000h-A0FFFFh

SA164 64 Kwords 10100001XX A10000h-A1FFFFh

SA165 64 Kwords 10100010XX A20000h-A2FFFFh

SA166 64 Kwords 10100011XX A30000h-A3FFFFh

SA167 64 Kwords 10100100XX A40000h-A4FFFFh

SA168 64 Kwords 10100101XX A50000h-A5FFFFh

SA169 64 Kwords 10100110XX A60000h-A6FFFFh

SA170 64 Kwords 10100111XX A70000h-A7FFFFh

SA171 64 Kwords 10101000XX A80000h-A8FFFFh

SA172 64 Kwords 10101001XX A90000h-A9FFFFh

SA173 64 Kwords 10101010XX AA0000h-AAFFFFh

SA174 64 Kwords 10101011XX AB0000h-ABFFFFh

SA175 64 Kwords 10101100XX AC0000h-ACFFFFh

SA176 64 Kwords 10101101XX AD0000h-ADFFFFh

SA177 64 Kwords 10101110XX AE0000h-AEFFFFh

SA178 64 Kwords 10101111XX AF0000h-AFFFFFh

Table 21. WS256N Sector & Memory Address Map (Continued)

Bank

Sector Sector Size A23–A14 (x16) Address Range

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 47

Preliminary

Bank 11

SA179 64 Kwords 10110000XX B00000h-B0FFFFh

SA180 64 Kwords 10110001XX B10000h-B1FFFFh

SA181 64 Kwords 10110010XX B20000h-B2FFFFh

SA182 64 Kwords 10110011XX B30000h-B3FFFFh

SA183 64 Kwords 10110100XX B40000h-B4FFFFh

SA184 64 Kwords 10110101XX B50000h-B5FFFFh

SA185 64 Kwords 10110110XX B60000h-B6FFFFh

SA186 64 Kwords 10110111XX B70000h-B7FFFFh

SA187 64 Kwords 10111000XX B80000h-B8FFFFh

SA188 64 Kwords 10111001XX B90000h-B9FFFFh

SA189 64 Kwords 10111010XX BA0000h-BAFFFFh

SA190 64 Kwords 10111011XX BB0000h-BBFFFFh

SA191 64 Kwords 10111100XX BC0000h-BCFFFFh

SA192 64 Kwords 10111101XX BD0000h-BDFFFFh

SA193 64 Kwords 10111110XX BE0000h-BEFFFFh

SA194 64 Kwords 10111111XX BF0000h-BFFFFFh

Bank 12

SA195 64 Kwords 11000000XX C00000h-C0FFFFh

SA196 64 Kwords 11000001XX C10000h-C1FFFFh

SA197 64 Kwords 11000010XX C20000h-C2FFFFh

SA198 64 Kwords 11000011XX C30000h-C3FFFFh

SA199 64 Kwords 11000100XX C40000h-C4FFFFh

SA200 64 Kwords 11000101XX C50000h-C5FFFFh

SA201 64 Kwords 11000110XX C60000h-C6FFFFh

SA202 64 Kwords 11000111XX C70000h-C7FFFFh

SA203 64 Kwords 11001000XX C80000h-C8FFFFh

SA204 64 Kwords 11001001XX C90000h-C9FFFFh

SA205 64 Kwords 11001010XX CA0000h-CAFFFFh

SA206 64 Kwords 11001011XX CB0000h-CBFFFFh

SA207 64 Kwords 11001100XX CC0000h-CCFFFFh

SA208 64 Kwords 11001101XX CD0000h-CDFFFFh

SA209 64 Kwords 11001110XX CE0000h-CEFFFFh

SA210 64 Kwords 11001111XX CF0000h-CFFFFFh

Table 21. WS256N Sector & Memory Address Map (Continued)

Bank

Sector Sector Size A23–A14 (x16) Address Range

48 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

Bank 13

SA211 64 Kwords 11010000XX D00000h-D0FFFFh

SA212 64 Kwords 11010001XX D10000h-D1FFFFh

SA213 64 Kwords 11010010XX D20000h-D2FFFFh

SA214 64 Kwords 11010011XX D30000h-D3FFFFh

SA215 64 Kwords 11010100XX D40000h-D4FFFFh

SA216 64 Kwords 11010101XX D50000h-D5FFFFh

SA217 64 Kwords 11010110XX D60000h-D6FFFFh

SA218 64 Kwords 11010111XX D70000h-D7FFFFh

SA219 64 Kwords 11011000XX D80000h-D8FFFFh

SA220 64 Kwords 11011001XX D90000h-D9FFFFh

SA221 64 Kwords 11011010XX DA0000h-DAFFFFh

SA222 64 Kwords 11011011XX DB0000h-DBFFFFh

SA223 64 Kwords 11011100XX DC0000h-DCFFFFh

SA224 64 Kwords 11011101XX DD0000h-DDFFFFh

SA225 64 Kwords 11011110XX DE0000h-DEFFFFh

SA226 64 Kwords 11011111XX DF0000h-DFFFFFh

Bank 14

SA227 64 Kwords 11100000XX E00000h-E0FFFFh

SA228 64 Kwords 11100001XX E10000h-E1FFFFh

SA229 64 Kwords 11100010XX E20000h-E2FFFFh

SA230 64 Kwords 11100011XX E30000h-E3FFFFh

SA231 64 Kwords 11100100XX E40000h-E4FFFFh

SA232 64 Kwords 11100101XX E50000h-E5FFFFh

SA233 64 Kwords 11100110XX E60000h-E6FFFFh

SA234 64 Kwords 11100111XX E70000h-E7FFFFh

SA235 64 Kwords 11101000XX E80000h-E8FFFFh

SA236 64 Kwords 11101001XX E90000h-E9FFFFh

SA237 64 Kwords 11101010XX EA0000h-EAFFFFh

SA238 64 Kwords 11101011XX EB0000h-EBFFFFh

SA239 64 Kwords 11101100XX EC0000h-ECFFFFh

SA240 64 Kwords 11101101XX ED0000h-EDFFFFh

SA241 64 Kwords 11101110XX EE0000h-EEFFFFh

SA242 64 Kwords 11101111XX EF0000h-EFFFFFh

Table 21. WS256N Sector & Memory Address Map (Continued)

Bank

Sector Sector Size A23–A14 (x16) Address Range

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 49

Preliminary

Bank 15

SA243 64 Kwords 11110000XX F00000h-F0FFFFh

SA244 64 Kwords 11110001XX F10000h-F1FFFFh

SA245 64 Kwords 11110010XX F20000h-F2FFFFh

SA246 64 Kwords 11110011XX F30000h-F3FFFFh

SA247 64 Kwords 11110100XX F40000h-F4FFFFh

SA248 64 Kwords 11110101XX F50000h-F5FFFFh

SA249 64 Kwords 11110110XX F60000h-F6FFFFh

SA250 64 Kwords 11110111XX F70000h-F7FFFFh

SA251 64 Kwords 11111000XX F80000h-F8FFFFh

SA252 64 Kwords 11111001XX F90000h-F9FFFFh

SA253 64 Kwords 11111010XX FA0000h-FAFFFFh

SA254 64 Kwords 11111011XX FB0000h-FBFFFFh

SA255 64 Kwords 11111100XX FC0000h-FCFFFFh

SA256 64 Kwords 11111101XX FD0000h-FDFFFFh

SA257 64 Kwords 11111110XX FE0000h-FEFFFFh

SA258 16 Kwords 1111111100 FF0000h-FF3FFFh

SA259 16 Kwords 1111111101 FF4000h-FF7FFFh

SA260 16 Kwords 1111111110 FF8000h-FFBFFFh

SA261 16 Kwords 1111111111 FFC000h-FFFFFFh

Table 22. WS128N Sector & Memory Address Map

Bank

Sector Sector Size A22–A14 (x16) Address Range

Bank 0

SA0 16 Kwords 000000000 000000h-003FFFh

SA1 16 Kwords 000000001 004000h-007FFFh

SA2 16 Kwords 000000010 008000h-00BFFFh

SA3 16 Kwords 000000011 00C000h-00FFFFh

SA4 64 Kwords 0000001XX 010000h-01FFFFh

SA5 64 Kwords 0000010XX 020000h-02FFFFh

SA6 64 Kwords 0000011XX 030000h-03FFFFh

SA7 64 Kwords 0000100XX 040000h-04FFFFh

SA8 64 Kwords 0000101XX 050000h-05FFFFh

SA9 64 Kwords 0000110XX 060000h-06FFFFh

SA10 64 Kwords 0000111XX 070000h-07FFFFh

Bank 1

SA11 64 Kwords 0001000XX 080000h-08FFFFh

SA12 64 Kwords 0001001XX 090000h-09FFFFh

SA13 64 Kwords 0001010XX 0A0000h-0AFFFFh

SA14 64 Kwords 0001011XX 0B0000h-0BFFFFh

SA15 64 Kwords 0001100XX 0C0000h-0CFFFFh

SA16 64 Kwords 0001101XX 0D0000h-0DFFFFh

SA17 64 Kwords 0001110XX 0E0000h-0EFFFFh

SA18 64 Kwords 0001111XX 0F0000h-0FFFFFh

Table 21. WS256N Sector & Memory Address Map (Continued)

Bank

Sector Sector Size A23–A14 (x16) Address Range

50 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

Bank 2

SA19 64 Kwords 0010000XX 100000h-10FFFFh

SA20 64 Kwords 0010001XX 110000h-11FFFFh

SA21 64 Kwords 0010010XX 120000h-12FFFFh

SA22 64 Kwords 0010011XX 130000h-13FFFFh

SA23 64 Kwords 0010100XX 140000h-14FFFFh

SA24 64 Kwords 0010101XX 150000h-15FFFFh

SA25 64 Kwords 0010110XX 160000h-16FFFFh

SA26 64 Kwords 0010111XX 170000h-17FFFFh

Bank 3

SA27 64 Kwords 0011000XX 180000h-18FFFFh

SA28 64 Kwords 0011001XX 190000h-19FFFFh

SA29 64 Kwords 0011010XX 1A0000h-1AFFFFh

SA30 64 Kwords 0011011XX 1B0000h-1BFFFFh

SA31 64 Kwords 0011100XX 1C0000h-1CFFFFh

SA32 64 Kwords 0011101XX 1D0000h-1DFFFFh

SA33 64 Kwords 0011110XX 1E0000h-1EFFFFh

SA34 64 Kwords 0011111XX 1F0000h-1FFFFFh

Bank 4

SA35 64 Kwords 0100000XX 200000h-20FFFFh

SA36 64 Kwords 0100001XX 210000h-21FFFFh

SA37 64 Kwords 0100010XX 220000h-22FFFFh

SA38 64 Kwords 0100011XX 230000h-23FFFFh

SA39 64 Kwords 0100100XX 240000h-24FFFFh

SA40 64 Kwords 0100101XX 250000h-25FFFFh

SA41 64 Kwords 0100110XX 260000h-26FFFFh

SA42 64 Kwords 0100111XX 270000h-27FFFFh

Bank 5

SA43 64 Kwords 0101000XX 280000h-28FFFFh

SA44 64 Kwords 0101001XX 290000h-29FFFFh

SA45 64 Kwords 0101010XX 2A0000h-2AFFFFh

SA46 64 Kwords 0101011XX 2B0000h-2BFFFFh

SA47 64 Kwords 0101100XX 2C0000h-2CFFFFh

SA48 64 Kwords 0101101XX 2D0000h-2DFFFFh

SA49 64 Kwords 0101110XX 2E0000h-2EFFFFh

SA50 64 Kwords 0101111XX 2F0000h-2FFFFFh

Bank 6

SA51 64 Kwords 0110000XX 300000h-30FFFFh

SA52 64 Kwords 0110001XX 310000h-31FFFFh

SA53 64 Kwords 0110010XX 320000h-32FFFFh

SA54 64 Kwords 0110011XX 330000h-33FFFFh

SA55 64 Kwords 0110100XX 340000h-34FFFFh

SA56 64 Kwords 0110101XX 350000h-35FFFFh

SA57 64 Kwords 0110110XX 360000h-36FFFFh

SA58 64 Kwords 0110111XX 370000h-37FFFFh

Table 22. WS128N Sector & Memory Address Map (Continued)

Bank

Sector Sector Size A22–A14 (x16) Address Range

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 51

Preliminary

Bank 7

SA59 64 Kwords 0111000XX 380000h-38FFFFh

SA60 64 Kwords 0111001XX 390000h-39FFFFh

SA61 64 Kwords 0111010XX 3A0000h-3AFFFFh

SA62 64 Kwords 0111011XX 3B0000h-3BFFFFh

SA63 64 Kwords 0111100XX 3C0000h-3CFFFFh

SA64 64 Kwords 0111101XX 3D0000h-3DFFFFh

SA65 64 Kwords 0111110XX 3E0000h-3EFFFFh

SA66 64 Kwords 0111111XX 3F0000h-3FFFFFh

Bank 8

SA67 64 Kwords 1000000XX 400000h-40FFFFh

SA68 64 Kwords 1000001XX 410000h-41FFFFh

SA69 64 Kwords 1000010XX 420000h-42FFFFh

SA70 64 Kwords 1000011XX 430000h-43FFFFh

SA71 64 Kwords 1000100XX 440000h-44FFFFh

SA72 64 Kwords 1000101XX 450000h-45FFFFh

SA73 64 Kwords 1000110XX 460000h-46FFFFh

SA74 64 Kwords 1000111XX 470000h-47FFFFh

Bank 9

SA75 64 Kwords 1001000XX 480000h-48FFFFh

SA76 64 Kwords 1001001XX 490000h-49FFFFh

SA77 64 Kwords 1001010XX 4A0000h-4AFFFFh

SA78 64 Kwords 1001011XX 4B0000h-4BFFFFh

SA79 64 Kwords 1001100XX 4C0000h-4CFFFFh

SA80 64 Kwords 1001101XX 4D0000h-4DFFFFh

SA81 64 Kwords 1001110XX 4E0000h-4EFFFFh

SA82 64 Kwords 1001111XX 4F0000h-4FFFFFh

Bank 10

SA83 64 Kwords 1010000XX 500000h-50FFFFh

SA84 64 Kwords 1010001XX 510000h-51FFFFh

SA85 64 Kwords 1010010XX 520000h-52FFFFh

SA86 64 Kwords 1010011XX 530000h-53FFFFh

SA87 64 Kwords 1010100XX 540000h-54FFFFh

SA88 64 Kwords 1010101XX 550000h-55FFFFh

SA89 64 Kwords 1010110XX 560000h-56FFFFh

SA90 64 Kwords 1010111XX 570000h-57FFFFh

Bank 11

SA91 64 Kwords 1011000XX 580000h-58FFFFh

SA92 64 Kwords 1011001XX 590000h-59FFFFh

SA93 64 Kwords 1011010XX 5A0000h-5AFFFFh

SA94 64 Kwords 1011011XX 5B0000h-5BFFFFh

SA95 64 Kwords 1011100XX 5C0000h-5CFFFFh

SA96 64 Kwords 1011101XX 5D0000h-5DFFFFh

SA97 64 Kwords 1011110XX 5E0000h-5EFFFFh

SA98 64 Kwords 1011111XX 5F0000h-5FFFFFh

Table 22. WS128N Sector & Memory Address Map (Continued)

Bank

Sector Sector Size A22–A14 (x16) Address Range

52 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

Bank 12

SA99 64 Kwords 1100000XX 600000h-60FFFFh

SA100 64 Kwords 1100001XX 610000h-61FFFFh

SA101 64 Kwords 1100010XX 620000h-62FFFFh

SA102 64 Kwords 1100011XX 630000h-63FFFFh

SA103 64 Kwords 1100100XX 640000h-64FFFFh

SA104 64 Kwords 1100101XX 650000h-65FFFFh

SA105 64 Kwords 1100110XX 660000h-66FFFFh

SA106 64 Kwords 1100111XX 670000h-67FFFFh

Bank 13

SA107 64 Kwords 1101000XX 680000h-68FFFFh

SA108 64 Kwords 1101001XX 690000h-69FFFFh

SA109 64 Kwords 1101010XX 6A0000h-6AFFFFh

SA110 64 Kwords 1101011XX 6B0000h-6BFFFFh

SA111 64 Kwords 1101100XX 6C0000h-6CFFFFh

SA112 64 Kwords 1101101XX 6D0000h-6DFFFFh

SA113 64 Kwords 1101110XX 6E0000h-6EFFFFh

SA114 64 Kwords 1101111XX 6F0000h-6FFFFFh

Bank 14

SA115 64 Kwords 1110000XX 700000h-70FFFFh

SA116 64 Kwords 1110001XX 710000h-71FFFFh

SA117 64 Kwords 1110010XX 720000h-72FFFFh

SA118 64 Kwords 1110011XX 730000h-73FFFFh

SA119 64 Kwords 1110100XX 740000h-74FFFFh

SA120 64 Kwords 1110101XX 750000h-75FFFFh

SA121 64 Kwords 1110110XX 760000h-76FFFFh

SA122 64 Kwords 1110111XX 770000h-77FFFFh

Bank 15

SA123 64 Kwords 1111000XX 780000h-78FFFFh

SA124 64 Kwords 1111001XX 790000h-79FFFFh

SA125 64 Kwords 1111010XX 7A0000h-7AFFFFh

SA126 64 Kwords 1111011XX 7B0000h-7BFFFFh

SA127 64 Kwords 1111100XX 7C0000h-7CFFFFh

SA128 64 Kwords 1111101XX 7D0000h-7DFFFFh

SA129 64 Kwords 1111110XX 7E0000h-7EFFFFh

SA130 16 Kwords 111111100 7F0000h-7F3FFFh

SA131 16 Kwords 111111101 7F4000h-7F7FFFh

SA132 16 Kwords 111111110 7F8000h-7FBFFFh

SA133 16 Kwords 111111111 7FC000h-7FFFFFh

Table 22. WS128N Sector & Memory Address Map (Continued)

Bank

Sector Sector Size A22–A14 (x16) Address Range

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 53

Preliminary

Table 23. WS064N Sector & Memory Address Map

Bank

Sector Sector Size A21–A14 (x16) Address Range

Bank 0

SA0 16 Kwords 00000000 000000h-003FFFh

SA1 16 Kwords 00000001 004000h-007FFFh

SA2 16 Kwords 00000010 008000h-00BFFFh

SA3 16 Kwords 00000011 00C000h-00FFFFh

SA4 64 Kwords 000001XX 010000h-01FFFFh

SA5 64 Kwords 000010XX 020000h-02FFFFh

SA6 64 Kwords 000011XX 030000h-03FFFFh

Bank 1

SA7 64 Kwords 000100XX 040000h-04FFFFh

SA8 64 Kwords 000101XX 050000h-05FFFFh

SA9 64 Kwords 000110XX 060000h-06FFFFh

SA10 64 Kwords 000111XX 070000h-07FFFFh

Bank 2

SA11 64 Kwords 001000XX 080000h-08FFFFh

SA12 64 Kwords 001001XX 090000h-09FFFFh

SA13 64 Kwords 001010XX 0A0000h-0AFFFFh

SA14 64 Kwords 001011XX 0B0000h-0BFFFFh

Bank 3

SA15 64 Kwords 001100XX 0C0000h-0CFFFFh

SA16 64 Kwords 001101XX 0D0000h-0DFFFFh

SA17 64 Kwords 001110XX 0E0000h-0EFFFFh

SA18 64 Kwords 001111XX 0F0000h-0FFFFFh

Bank 4

SA19 64 Kwords 010000XX 100000h-10FFFFh

SA20 64 Kwords 010001XX 110000h-11FFFFh

SA21 64 Kwords 010010XX 120000h-12FFFFh

SA22 64 Kwords 010011XX 130000h-13FFFFh

Bank 5

SA23 64 Kwords 010100XX 140000h-14FFFFh

SA24 64 Kwords 010101XX 150000h-15FFFFh

SA25 64 Kwords 010110XX 160000h-16FFFFh

SA26 64 Kwords 010111XX 170000h-17FFFFh

Bank 6

SA27 64 Kwords 011000XX 180000h-18FFFFh

SA28 64 Kwords 011001XX 190000h-19FFFFh

SA29 64 Kwords 011010XX 1A0000h-1AFFFFh

SA30 64 Kwords 011011XX 1B0000h-1BFFFFh

Bank 7

SA31 64 Kwords 011100XX 1C0000h-1CFFFFh

SA32 64 Kwords 011101XX 1D0000h-1DFFFFh

SA33 64 Kwords 011110XX 1E0000h-1EFFFFh

SA34 64 Kwords 011111XX 1F0000h-1FFFFFh

Bank 8

SA35 64 Kwords 100000XX 200000h-20FFFFh

SA36 64 Kwords 100001XX 210000h-21FFFFh

SA37 64 Kwords 100010XX 220000h-22FFFFh

SA38 64 Kwords 100011XX 230000h-23FFFFh

54 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

Bank 9

SA39 64 Kwords 100100XX 240000h-24FFFFh

SA40 64 Kwords 100101XX 250000h-25FFFFh

SA41 64 Kwords 100110XX 260000h-26FFFFh

SA42 64 Kwords 100111XX 270000h-27FFFFh

Bank 10

SA43 64 Kwords 101000XX 280000h-28FFFFh

SA44 64 Kwords 101001XX 290000h-29FFFFh

SA45 64 Kwords 101010XX 2A0000h-2AFFFFh

SA46 64 Kwords 101011XX 2B0000h-2BFFFFh

Bank 11

SA47 64 Kwords 101100XX 2C0000h-2CFFFFh

SA48 64 Kwords 101101XX 2D0000h-2DFFFFh

SA49 64 Kwords 101110XX 2E0000h-2EFFFFh

SA50 64 Kwords 101111XX 2F0000h-2FFFFFh

Bank 12

SA51 64 Kwords 110000XX 300000h-30FFFFh

SA52 64 Kwords 110001XX 310000h-31FFFFh

SA53 64 Kwords 110010XX 320000h-32FFFFh

SA54 64 Kwords 110011XX 330000h-33FFFFh

Bank 13

SA55 64 Kwords 110100XX 340000h-34FFFFh

SA56 64 Kwords 110101XX 350000h-35FFFFh

SA57 64 Kwords 110110XX 360000h-36FFFFh

SA58 64 Kwords 110111XX 370000h-37FFFFh

Bank 14

SA59 64 Kwords 111000XX 380000h-38FFFFh

SA60 64 Kwords 111001XX 390000h-39FFFFh

SA61 64 Kwords 111010XX 3A0000h-3AFFFFh

SA62 64 Kwords 111011XX 3B0000h-3BFFFFh

Bank 15

SA63 64 Kwords 111100XX 3C0000h-3CFFFFh

SA64 64 Kwords 111101XX 3D0000h-3DFFFFh

SA65 64 Kwords 111110XX 3E0000h-3EFFFFh

SA66 16 Kwords 11111100 3F0000h-3F3FFFh

SA67 16 Kwords 11111101 3F4000h-3F7FFFh

SA68 16 Kwords 11111110 3F8000h-3FBFFFh

SA69 16 Kwords 11111111 3FC000h-3FFFFFh

Table 23. WS064N Sector & Memory Address Map (Continued)

Bank

Sector Sector Size A21–A14 (x16) Address Range

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 55

Preliminary

Command Definitions

Writing specific address and data commands or sequences into the command

defines the valid register command sequences. Writing incorrect address and

data values or writing them in the improper sequence may place the device in an

unknown state. The system must write the reset command to return the device

to reading array data. See “AC Characteristics—Synchronous” and “AC Charac-

teristics—Asynchronous” for timing diagrams.

Reading Array Data

The device is automatically set to reading asynchronous array data after device

power-up. No commands are required to retrieve data in asynchronous mode.

Each bank is ready to read array data after completing an Embedded Program or

Embedded Erase algorithm.

After the device accepts an Erase Suspend command, the corresponding bank

enters the erase-suspend-read mode, after which the system can read data from

any non-erase-suspended sector within the same bank. After completing a pro-

gramming operation in the Erase Suspend mode, the system may once again

read array data from any non-erase-suspended sector within the same bank. See

Erase Suspend/Erase Resume Commands for more information.

After the device accepts a Program Suspend command, the corresponding bank

enters the program-suspend-read mode, after which the system can read data

from any non-program-suspended sector within the same bank. See Program

Suspend/Program Resume Commands for more information.

The system must issue the reset command to return a bank to the read (or erase-

suspend-read) mode if DQ5 goes high during an active program or erase opera-

tion, or if the bank is in the autoselect mode. See Reset Command for more

information. If DQ1 goes high during Write Buffer Programming, the system must

issue the Write Buffer Abort Reset command.

See also Requirements for Asynchronous (Non-Burst) Read Operation and Re-

quirements for Synchronous (Burst) Read Operation for more information. The

Asynchronous Read and Synchronous/Burst Read tables provide the read param-

eters, and Figure 13, and Figure 17 show the timings.

Set Configuration Register Command Sequence

The device uses a configuration register to set the various burst parameters:

number of wait states, burst read mode, RDY configuration, and synchronous

mode active (see Figure 27 for details). The configuration register must be set

before the device will enter burst mode. On power up or reset, the device is set

in asynchronous read mode and the configuration register is reset. The configu-

ration register is not reset after deasserting CE#.

The configuration register is loaded with a four-cycle command sequence. The

first two cycles are standard unlock sequences. On the third cycle, the data

should be D0h and address bits should be 555h. During the fourth cycle, the con-

figuration code should be entered onto the data bus with the address bus set to

address 000h. Once the data has been programmed into the configuration regis-

ter, a software reset command is required to set the device into the correct state.

The device will power up or after a hardware reset with the default setting, which

is in asynchronous mode. The register must be set before the device can enter

56 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

synchronous mode. The configuration register can not be changed during device

operations (program, erase, or sector lock).

Read Configuration Register Command Sequence

The configuration register can be read with a four-cycle command sequence. The

first two cycles are standard unlock sequences. On the third cycle, the data

should be C6h and address bits should be 555h. During the fourth cycle, the con-

figuration code should be read out of the data bus with the address bus set to

address 000h. Once the data has been read from the configuration register, a

software reset command is required to set the device into the array read mode.

Figure 1. Synchronous/Asynchronous State Diagram

Read Mode Setting

This setting allows the system to enable or disable burst mode during system op-

erations. Configuration Bit CR15 determines this setting: “1’ for asynchronous

mode, “0” for synchronous mode.

Programmable Wait State Configuration

The programmable wait state feature informs the device of the number of clock

cycles that must elapse after AVD# is driven active before data will be available.

This value is determined by the input frequency of the device. Configuration Bit

CR13–CR11 determine the setting (see Tab l e 2 4 ).

The wait state command sequence instructs the device to set a particular number

of clock cycles for the initial access in burst mode. The number of wait states that

should be programmed into the device is directly related to the clock frequency.

Power-up/

Hardware Reset

Asynchronous Read

Mode Only

Synchronous Read

Mode Only

Set Burst Mode

Configuration Register

Command for

Synchronous Mode

(D15 = 0)

Set Burst Mode

Configuration Register

Command for

Asynchronous Mode

(D15 = 1)

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 57

Preliminary

Ta b l e 2 4. Programmable Wait State Settings

It is recommended that the wait state command sequence be written, even if the

default wait state value is desired, to ensure the device is set as expected. A

hardware reset will set the wait state to the default setting.

Programmable Wait State

If the device is equipped with the handshaking option, the host system should set

CR13-CR11 to 010 for a clock frequency of 54 MHz, to 011 for a clock frequency

of 66 MHz, or to 100 for a clock frequency of 80 MHz for the system/device to

execute at maximum speed.

Table 25 describes the typical number of clock cycles (wait states) for various

conditions.

Boundary Crossing Latency

If the device is operating above 66 MHz, an additional wait state must be inserted

to account for boundary crossing latency. This is done by setting CR14 to a ‘1’

(default). If the device is operating at or below 66 MHz, the additional wait state

for boundary crossing is not needed. Therefore the CR14 can be changed to a ‘0’

to remove boundary crossing latency.

Ta bl e 2 5 . Wait States for Handshaking

Handshaking

For optimal burst mode performance, the host system must set the appropriate

number of wait states in the flash device depending on the clock frequency.

The autoselect function allows the host system to determine whether the flash

device is enabled for handshaking. See Autoselect Command Sequence for more

information.

Burst Length Configuration

The device supports four different read modes: continuous mode, and 8, 16, and

32 word linear with or without wrap around modes. A continuous sequence (de-

CR13 CR12 CR11 Total Initial Access Cycles

0 0 0 2

0 0 1 3

0 1 0 4

0 1 1 5

1 0 0 6

1 0 1 7 (default)

1 1 0 Reserved

1 1 1 Reserved

Notes:

1. Upon power-up or hardware reset, the default setting is seven wait states.

2. RDY will default to being active with data when the Wait State Setting is set

to a total initial access cycle of 2.

Conditions at Address

Typical No. of Clock Cycles after AVD#

Low

54 MHz 66 MHz 80 MHz

Initial address (V

= 1.8 V) 456

58 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

fault) begins at the starting address and advances the address pointer until the

burst operation is complete. If the highest address in the device is reached during

the continuous burst read mode, the address pointer wraps around to the lowest

address.

For example, an eight-word linear read with wrap around begins on the starting

address written to the device and then advances to the next 8 word boundary.

The address pointer then returns to the 1st word after the previous eight word

boundary, wrapping through the starting location. The sixteen- and thirty-two lin-

ear wrap around modes operate in a fashion similar to the eight-word mode.

Tab l e 2 6 shows the CR2-CR0 and settings for the four read modes.

Ta bl e 2 6 . Burst Length Configuration

Burst Wrap Around

By default, the device will perform burst wrap around with CR3 set to a ‘1’.

Changing the CR3 to a ‘0’ disables burst wrap around.

RDY Configuration

By default, the device is set so that the RDY pin will output VOH whenever there

is valid data on the outputs. The device can be set so that RDY goes active one

data cycle before active data. CR8 determines this setting; “1” for RDY active

(default) with data, “0” for RDY active one clock cycle before valid data.

RDY Polarity

By default, the RDY pin will always indicate that the device is ready to handle a

new transaction with CR10 set to a ‘1’. In this case, the RDY pin is active high.

Changing the CR10 to a ‘0’ sets the RDY pin to be active low. In this case, the

RDY pin will always indicate that the device is ready to handle a new transaction

when low.

Burst Modes

Address Bits

CR2 CR1 CR0

Continuous 000

8-word linear 010

16-word linear 011

32-word linear 100

Note: Upon power-up or hardware reset the default setting is continuous.

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 59

Preliminary

Configuration Register

Tab l e 2 7 shows the address bits that determine the configuration register settings

for various device functions.

Ta bl e 2 7 . Configuration Register

Reset Command

Writing the reset command resets the banks to the read or erase-suspend-read

mode. Address bits are don’t cares for this command.

The reset command may be written between the sequence cycles in an erase

command sequence before erasing begins. This resets the bank to which the sys-

tem was writing to the read mode. Once erasure begins, however, the device

ignores reset commands until the operation is complete.

The reset command may be written between the sequence cycles in a program

command sequence before programming begins (prior to the third cycle). This re-

CR Bit Function

Settings (Binary)

CR15 Set Device Read Mode 0 = Synchronous Read (Burst Mode) Enabled

1 = Asynchronous Mode (default)

CR14 Boundary Crossing 0 = No extra boundary crossing latency

1 = With extra boundary crossing latency (default)

CR13

Programmable

Wait State

000 = Data is valid on the 2nd active CLK edge after addresses are latched

001 = Data is valid on the 3rd active CLK edge after addresses are latched

010 = Data is valid on the 4th active CLK edge after addresses are latched

011 = Data is valid on the 5th active CLK edge after addresses are latched

100 = Data is valid on the 6th active CLK edge after addresses are latched

101 = Data is valid on the 7th active CLK edge after addresses are latched (default)

110 = Reserved

111 = Reserved

CR12

CR11

CR10 RDY Polarity 0 = RDY signal is active low

1 = RDY signal is active high (default)

CR9 Reserved 1 = default

CR8 RDY 0 = RDY active one clock cycle before data

1 = RDY active with data (default)

CR7 Reserved 1 = default

CR6 Reserved 1 = default

CR5 Reserved 0 = default

CR4 Reserved 0 = default

CR3 Burst Wrap Around 0 = No Wrap Around Burst

1 = Wrap Around Burst (default)

CR2

Burst Length

000 = Continuous (default)

010 = 8-Word Linear Burst

011 = 16-Word Linear Burst

100 = 32-Word Linear Burst

(All other bit settings are reserved)

CR1

CR0

Note:

1. Device will be in the default state upon power-up or hardware reset.

2. If CR2 is set to ‘0’, then the CR3 bit will automatically revert to 1 regardless of the user setting.

60 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

sets the bank to which the system was writing to the read mode. If the program

command sequence is written to a bank that is in the Erase Suspend mode, writ-

ing the reset command returns that bank to the erase-suspend-read mode. Once

programming begins, however, the device ignores reset commands until

the operation is complete.

The reset command may be written between the sequence cycles in an autoselect

command sequence. Once in the autoselect mode, the reset command must be

written to return to the read mode. If a bank entered the autoselect mode while

in the Erase Suspend mode, writing the reset command returns that bank to the

erase-suspend-read mode.

If DQ5 goes high during a program or erase operation, writing the reset command

returns the banks to the read mode (or erase-suspend-read mode if that bank

was in Erase Suspend and program-suspend-read mode if that bank was in Pro-

gram Suspend).

Note: If DQ1 goes high during a Write Buffer Programming operation, the system

must write the “Write to Buffer Abort Reset” command sequence to RESET the

device to reading array data. The standard RESET command will not work. See

Table 17 for details on this command sequence.

Autoselect Command Sequence

The autoselect command sequence allows the host system to access the manu-

facturer and device codes, and determine whether or not a sector is protected.

The Command Definition Summary shows the address and data requirements.

The autoselect command sequence may be written to an address within a bank

that is either in the read or erase-suspend-read mode. The autoselect command

may not be written while the device is actively programming or erasing in the

other bank. Autoselect does not support simultaneous operations nor burst

mode.

The autoselect command sequence is initiated by first writing two unlock cycles.

This is followed by a third write cycle that contains the bank address and the au-

toselect command. The bank then enters the autoselect mode. The system may

read at any address within the same bank any number of times without initiating

another autoselect command sequence. Read commands to other banks will re-

turn data from the array. Writes to other banks is not allowed. The following table

describes the address requirements for the various autoselect functions, and the

resulting data. BA represents the bank address. The device ID is read in three

cycles.

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 61

Preliminary

Ta b le 2 8 . Autoselect Addresses

The system must write the reset command to return to the read mode (or erase-

suspend-read mode if the bank was previously in Erase Suspend).

Enter SecSi™ Sector/Exit SecSi Sector Command Sequence

The SecSi Sector region provides a secured data area containing a random, eight

word electronic serial number (ESN). The system can access the SecSi Sector re-

gion by issuing the three-cycle Enter SecSi Sector command sequence. The

device continues to access the SecSi Sector region until the system issues the

four-cycle Exit SecSi Sector command sequence. The Exit SecSi Sector command

sequence returns the device to normal operation. The SecSi Sector is not acces-

sible when the device is executing an Embedded Program or embedded Erase

algorithm. See Command Definition Summary for address and data requirements

for both command sequences.

Word Program Command Sequence

Programming is a four-bus-cycle operation. The program command sequence is

initiated by writing two unlock write cycles, followed by the program set-up com-

mand. The program address and data are written next, which in turn initiate the

Embedded Program algorithm. The system is not required to provide further con-

trols or timings. The device automatically provides internally generated program

pulses and verifies the programmed cell margin (see Figure 2).

When the Embedded Program algorithm is complete, the device then returns to

the read mode and addresses are no longer latched. The system can determine

the status of the program operation by using DQ7 or DQ6. Refer to the Write Op-

eration Status section for information on these status bits.

Any commands written to the device during the Embedded Program Algorithm

are ignored except the Program Suspend command. Note that the SecSi Sec-

Description Address Read Data

Manufacturer ID (BA) + 00h 0001h

Device ID, Word 1 (BA) + 01h 227Eh

Device ID, Word 2 (BA) + 0Eh

2230 (WS256N)

2232 (WS064N)

2231 (WS128N)

Device ID, Word 3 (BA) + 0Fh 2200

Indicator Bits

(See Note) (BA) + 03h

DQ15 - DQ8 = Reserved

DQ7 (Factory Lock Bit): 1 = Locked, 0 = Not Locked

DQ6 (Customer Lock Bit): 1 = Locked, 0 = Not Locked

DQ5 (Handshake Bit): 1 = Reserved, 0 = Standard Handshake

DQ4, DQ3 (WP# Protection Boot Code): 00 = WP# Protects both Top Boot and

Bottom Boot Sectors. 01, 10, 11 = Reserved

DQ2 = Reserved

DQ1 (DYB Power up State [Lock Register DQ4]): 1 = Unlocked (user option), 0 =

Locked (default)

DQ0 (PPB Eraseability [Lock Register DQ3]): 1 = Erase allowed, 0 = Erase

disabled

Sector Block Lock/

Unlock (SA) + 02h 0001h = Locked, 0000h = Unlocked

Note: For WS128N and WS064, DQ1 and DQ0 will be reserved.

62 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

tor, autoselect, and CFI functions are unavailable when a program

operation is in progress. Note that a hardware reset immediately terminates

the program operation. The program command sequence should be reinitiated

once the device has returned to the read mode, to ensure data integrity.

Programming is allowed in any sequence and across sector boundaries. Program-

ming to the same word address multiple times without intervening erases is

limited. For such application requirements, please contact your local Spansion

representative. A “0” cannot be programmed back to a “1.” Attempting to

do so may cause the device to set DQ5 = 1 (halting any further operation and re-

quiring a reset command). A succeeding read will show that the data is still “0.”

Only erase operations can convert a “0” to a “1.” See Figure 2.

Figure 2. Word Program Operation

Write Buffer Programming Command Sequence

Write Buffer Programming Command Sequence allows for faster programming

compared to the standard Program Command Sequence. Write Buffer Program-

ming allows the system to write up to 32 words in one programming operation.

See Write Buffer Programming Operation section for the program command

sequence.

START

Write Program

Command Sequence

Data Poll

from System

Verify Data? No

Yes

Last Address?

Yes

Programming

Completed

Increment Address

Embedded

Program

algorithm

in progress

Note: See Command Definition Summary for program command sequence.

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 63

Preliminary

Ta bl e 2 9 . Write Buffer Command Sequence

Sequence Address Data Comment

Unlock Command 1 555 00AA Not required in the Unlock Bypass mode

Unlock Command 2 2AA 0055 Same as above

Write Buffer Load Starting Address 0025h

Specify the Number of Program

Locations Starting Address Word Count Number of locations to program minus 1

Load 1st data word Starting Address Program Data All addresses must be within write-buffer-page

boundaries, but do not have to be loaded in any order

Load next data word Write Buffer

Location Program Data Same as above

... ... ... Same as above

Load last data word Write Buffer

Location Program Data Same as above

Write Buffer Program Confirm Sector Address 0029h This command must follow the last write buffer location

loaded, or the operation will ABORT

Device goes busy

Status monitoring through DQ pins

(Perform Data Bar Polling on the Last

Loaded Address)

64 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

Figure 3. Write Buffer Programming Operation

Write “Write to Buffer”

command and

Sector Address

Write number of addresses

to program minus 1

and Sector Address

Write program buffer to

flash sector address

Write first address/data

Write to a different

sector address

FAIL or ABORT PASS

Read DQ15 - DQ0 at

Last Loaded Address

Read DQ15 - DQ0 with

address = Last Loaded

Address

Write next address/data pair

WC = WC - 1

WC = 0 ?

Part of “Write to Buffer”

Command Sequence

Yes

Abort Write to

Buffer Operation?

DQ7 = Data?

DQ5 = 1?DQ1 = 1?

Write to buffer ABORTED.

Must write “Write-to-buffer

Abort Reset” command

sequence to return

to read mode.

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 65

Preliminary

Unlock Bypass Command Sequence

The unlock bypass feature allows faster programming than the standard word

program command sequence. The unlock bypass command sequence is initiated

by first writing two unlock cycles. This is followed by a third write cycle containing

the unlock bypass command, 20h. The device then enters the unlock bypass

mode. A two-cycle unlock bypass program command sequence is all that is re-

quired to program in this mode. The first cycle in this sequence contains the

unlock bypass program command, A0h; the second cycle contains the program

address and data. Additional data is programmed in the same manner. This mode

dispenses with the initial two unlock cycles required in the standard program

command sequence, resulting in faster total programming time. See Command

Definition Summary for the unlock bypass command sequences requirements.

During the unlock bypass mode, only the Read, Unlock Bypass Program, and Un-

lock Bypass Reset commands are valid. To exit the unlock bypass mode, the

system must issue the two-cycle unlock bypass reset command sequence. The

first cycle must contain the bank address and the data 90h. The second cycle

need only contain the data 00h. The bank then returns to the read mode.

Chip Erase Command Sequence

Chip erase is a six bus cycle operation. The chip erase command sequence is ini-

tiated by writing two unlock cycles, followed by a set-up command. Two

additional unlock write cycles are then followed by the chip erase command,

which in turn invokes the Embedded Erase algorithm. The device does not require

the system to preprogram prior to erase. The Embedded Erase algorithm auto-

matically preprograms and verifies the entire memory for an all zero data pattern

prior to electrical erase. The system is not required to provide any controls or tim-

ings during these operations. See Command Definition Summary for chip erase

command sequence address and data requirements.

When the Embedded Erase algorithm is complete, that bank returns to the read

mode and addresses are no longer latched. The system can determine the status

of the erase operation by using DQ7 or DQ6/DQ2. See Write Operation Status for

information on these status bits.

Any commands written during the chip erase operation are ignored. However,

note that a hardware reset immediately terminates the erase operation. If that

occurs, the chip erase command sequence should be reinitiated once that bank

has returned to reading array data, to ensure data integrity.

Figure 4 illustrates the algorithm for the erase operation. See Erase/Program

Timing for parameters and timing diagrams.

Sector Erase Command Sequence

Sector erase is a six bus cycle operation. The sector erase command sequence is

initiated by writing two unlock cycles, followed by a set-up command. Two addi-

tional unlock cycles are written, and are then followed by the address of the

sector to be erased, and the sector erase command. See Command Definition

Summary for sector erase command sequence address and data requirements.

The device does not require the system to preprogram prior to erase. The Em-

bedded Erase algorithm automatically programs and verifies the entire memory

for an all zero data pattern prior to electrical erase. The system is not required to

provide any controls or timings during these operations.

66 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

After the command sequence is written, a sector erase time-out of no less than

tSEA occurs. During the time-out period, additional sector addresses and sector

erase commands may be written. Loading the sector erase buffer may be done

in any sequence, and the number of sectors may be from one sector to all sectors.

The time between these additional cycles must be less than tSEA. Any sector erase

address and command following the exceeded time-out (tSEA) may or may not be

accepted. Any command other than Sector Erase or Erase Suspend during the

time-out period resets that bank to the read mode.

The system can monitor DQ3 to determine if the sector erase timer has timed out

(See DQ3: Sector Erase Start Timeout State Indicator.) The time-out begins from

the rising edge of the final WE# pulse in the command sequence.

When the Embedded Erase algorithm is complete, the bank returns to reading

array data and addresses are no longer latched. Note that while the Embedded

Erase operation is in progress, the system can read data from the non-erasing

banks. The system can determine the status of the erase operation by reading

DQ7 or DQ6/DQ2 in the erasing bank. See Write Operation Status for information

on these status bits.

Once the sector erase operation has begun, only the Erase Suspend command is

valid. All other commands are ignored. However, note that a hardware reset im-

mediately terminates the erase operation. If that occurs, the sector erase

command sequence should be reinitiated once that bank has returned to reading

array data, to ensure data integrity.

Figure 4 illustrates the algorithm for the erase operation. See Erase/Program

Timing for parameters and timing diagrams.

Figure 4. Erase Operation

START

Write Erase

Command Sequence

Data Poll

from System

Data = FFh?

Yes

Erasure Completed

Embedde

Erase

algorithm

in progres

Notes:

1. See Command Definition Summary for erase command sequence.

2. See the section on DQ3 for information on the sector erase timer.

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 67

Preliminary

Erase Suspend/Erase Resume Commands

The Erase Suspend command allows the system to interrupt a sector erase oper-

ation and then read data from, or program data to, any sector not selected for

erasure. The bank address is required when writing this command. This com-

mand is valid only during the sector erase operation, including the tSEA time-out

period during the sector erase command sequence. The Erase Suspend command

is ignored if written during the chip erase operation.

When the Erase Suspend command is written during the sector erase operation,

the device requires tESL (erase suspend latency) to suspend the erase operation.

However, when the Erase Suspend command is written during the sector erase

time-out, the device immediately terminates the time-out period and suspends

the erase operation.

After the erase operation has been suspended, the bank enters the erase-sus-

pend-read mode. The system can read data from or program data to any sector

not selected for erasure. (The device “erase suspends” all sectors selected for

erasure.) Reading at any address within erase-suspended sectors produces sta-

tus information on DQ7–DQ0. The system can use DQ7, or DQ6 and DQ2

together, to determine if a sector is actively erasing or is erase-suspended. Refer

to Ta bl e 3 3 for information on these status bits.

After an erase-suspended program operation is complete, the bank returns to the

erase-suspend-read mode. The system can determine the status of the program

operation using the DQ7 or DQ6 status bits, just as in the standard program

operation.

In the erase-suspend-read mode, the system can also issue the autoselect com-

mand sequence. See Write Buffer Programming Operation and the Autoselect

Command Sequence for details.

To resume the sector erase operation, the system must write the Erase Resume

command. The bank address of the erase-suspended bank is required when writ-

ing this command. Further writes of the Resume command are ignored. Another

Erase Suspend command can be written after the chip has resumed erasing.

Program Suspend/Program Resume Commands

The Program Suspend command allows the system to interrupt an embedded

programming operation or a “Write to Buffer” programming operation so that

data can read from any non-suspended sector. When the Program Suspend com-

mand is written during a programming process, the device halts the

programming operation within tPSL (program suspend latency) and updates the

status bits. Addresses are “don’t-cares” when writing the Program Suspend

command.

After the programming operation has been suspended, the system can read array

data from any non-suspended sector. The Program Suspend command may also

be issued during a programming operation while an erase is suspended. In this

case, data may be read from any addresses not in Erase Suspend or Program

Suspend. If a read is needed from the SecSi Sector area, then user must use the

proper command sequences to enter and exit this region.

The system may also write the autoselect command sequence when the device

is in Program Suspend mode. The device allows reading autoselect codes in the

suspended sectors, since the codes are not stored in the memory array. When the

device exits the autoselect mode, the device reverts to Program Suspend mode,

68 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

and is ready for another valid operation. See “Autoselect Command Sequence”

for more information.

After the Program Resume command is written, the device reverts to program-

ming. The system can determine the status of the program operation using the

DQ7 or DQ6 status bits, just as in the standard program operation. See “Write

Operation Status” for more information.

The system must write the Program Resume command (address bits are “don’t

care”) to exit the Program Suspend mode and continue the programming opera-

tion. Further writes of the Program Resume command are ignored. Another

Program Suspend command can be written after the device has resumed

programming.

Lock Register Command Set Definitions

The Lock Register Command Set permits the user to program the SecSi Sector

Protection Bit, Persistent Protection Mode Lock Bit, or Password Protection Mode

Lock Bit one time. The Lock Command Set also allows for the reading of the SecSi

Sector Protection Bit, Persistent Protection Mode Lock Bit, or Password Protection

Mode Lock Bit.

The Lock Register Command Set Entry command sequence must be issued

prior to any of the following commands to enable proper command execution.

Lock Register Program Command

Lock Register Read Command

Lock Register Exit Command

Note that issuing the Lock Register Command Set Entry command disables reads

and writes for Bank 0. Reads from other banks excluding Bank 0 are allowed.

The Lock Register Command Set Exit command must be issued after the execu-

tion of the commands to reset the device to read mode, and re-enables reads and

writes for Bank 0.

Note that if the Persistent Protection Mode Locking Bit and the Password Protec-

tion Mode Locking Bit are programmed at the same time, neither will be

programmed.

Password Protection Command Set Definitions

The Password Protection Command Set permits the user to program the 64-bit

password, verify the programming of the 64-bit password, and then later unlock

the device by issuing the valid 64-bit password.

The Password Protection Command Set Entry command sequence must be

issued prior to any of the following commands to enable proper command

execution.

Password Program Command

Password Read Command

Password Unlock Command

Note that issuing the Password Protection Command Set Entry command

disables reads and writes for Bank 0. Reads and writes for other banks excluding

Bank 0 are allowed.

The Password Program Command permits programming the password that is

used as part of the hardware protection scheme. The actual password is 64 bits

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 69

Preliminary

long. There is no special addressing order required for programming the

password.

Once the Password is written and verified, the Password Mode Locking Bit must

be set in order to prevent verification. The Password Program Command is only

capable of programming “0”s. Programming a “1” after a cell is programmed as

a “0” results in a time-out by the Embedded Program Algorithm with the cell re-

maining as a “0”. The password is all “1”s when shipped from the factory. All 64-

bit password combinations are valid as a password.

The Password Verify Command is used to verify the Password. The Password is

verifiable only when the Password Mode Locking Bit is not programmed. If the

Password Mode Locking Bit is programmed and the user attempts to verify the

Password, the device will always drive all “1”s onto the DQ data bus.

The lower two address bits (A1–A0) are valid during the Password Read, Pass-

word Program, and Password Unlock.

The Password Unlock command is used to clear the PPB Lock Bit so that the PPBs

can be unlocked for modification, thereby allowing the PPBs to become accessible

for modification. The exact password must be entered in order for the unlocking

function to occur. This command cannot be issued any faster than 1 µs at a time

to prevent a hacker from running through all the 64-bit combinations in an at-

tempt to correctly match a password. If the command is issued before the 1 µs

execution window for each portion of the unlock, the command will be ignored.

The Password Unlock function is accomplished by writing Password Unlock com-

mand and data to the device to perform the clearing of the PPB Lock Bit. The

password is 64 bits long. A1 and A0 are used for matching. Writing the Password

Unlock command does not need to be address order specific. An example se-

quence is starting with the lower address A1–A0= 00, followed by A1–A0= 01,

A1–A0= 10, and A1–A0= 11.

Approximately 1 µSec is required for unlocking the device after the valid 64-bit

password is given to the device. It is the responsibility of the microprocessor to

keep track of the 64-bit password as it is entered with the Password Unlock com-

mand, the order, and when to read the PPB Lock bit to confirm successful

password unlock. In order to re-lock the device into the Password Mode, the PPB

Lock Bit Set command can be re-issued.

The Password Protection Command Set Exit command must be issued after

the execution of the commands listed previously to reset the device to read

mode, otherwise the device will hang. Note that issuing the Password Protec-

tion Command Set Exit command re-enables reads and writes for Bank 0.

Non-Volatile Sector Protection Command Set Definitions

The Non-Volatile Sector Protection Command Set permits the user to program the

Persistent Protection Bits (PPBs), erase all of the Persistent Protection Bits (PPBs),

and read the logic state of the Persistent Protection Bits (PPBs).

The Non-Volatile Sector Protection Command Set Entry command se-

quence must be issued prior to any of the following commands to enable proper

command execution.

PPB Program Command

All PPB Erase Command

PPB Status Read Command

70 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

Note that issuing the Non-Volatile Sector Protection Command Set Entry

command disables reads and writes for the bank selected. Reads within that bank

will return the PPB status for that sector. Reads from other banks are allowed;

writes are not allowed. All Reads must be performed using the Asynchronous

mode.

The PPB Program command is used to program, or set, a given PPB. Each PPB is

individually programmed (but is bulk erased with the other PPBs). The specific

sector address (A23–A14 WS256N, A22–A14 WS128N, A21–A14 WS064N) are

written at the same time as the program command. If the PPB Lock Bit is set, the

PPB Program command will not execute and the command will time-out without

programming the PPB.

The All PPB Erase command is used to erase all PPBs in bulk. There is no means

for individually erasing a specific PPB. Unlike the PPB program, no specific sector

address is required. However, when the PPB erase command is written, all Sector

PPBs are erased in parallel. If the PPB Lock Bit is set the ALL PPB Erase command

will not execute and the command will time-out without erasing the PPBs.

The device will preprogram all PPBs prior to erasing when issuing the All PPB

Erase command. Also note that the total number of PPB program/erase cycles has

the same endurance as the flash memory array.

The programming state of the PPB for a given sector can be verified by writing a

PPB Status Read Command to the device.

The Non-Volatile Sector Protection Command Set Exit command must be

issued after the execution of the commands listed previously to reset the device

to read mode. Note that issuing the Non-Volatile Sector Protection Com-

mand Set Exit command re-enables reads and writes for Bank 0.

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 71

Preliminary

Figure 5. PPB Program/Erase Algorithm

Read Byte Twice.

Addr = SA0

Enter PPB

Command Set.

Addr = BA

Program PPB Bit.

Addr = SA

Read Byte.

Addr = SA0

DQ5 = 1?

Yes

DQ6 =

Toggle?

DQ6 =

Toggle?

Read Byte.

Addr = SA0

Read Byte.

Addr = SA

PASS

FAIL

Issue Reset

Command

Exit PPB

Command Set

DQ0 =

'1' (Erase)

'0' (Pgm.)?

72 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

Global Volatile Sector Protection Freeze Command Set

The Global Volatile Sector Protection Freeze Command Set permits the user to set

the PPB Lock Bit and read the logic state of the PPB Lock Bit.

The Volatile Sector Protection Freeze Command Set Entry command se-

quence must be issued prior to any of the commands listed following to enable

proper command execution:

PPB Lock Bit Set Command

PPB Lock Bit Status Read Command

Reads from all non-busy remaining 15 banks are allowed.

The PPB Lock Bit Set command is used to set the PPB Lock bit if it is cleared either

at reset or if the Password Unlock command was successfully executed. There is

no PPB Lock Bit Clear command. Once the PPB Lock Bit is set, it cannot be cleared

unless the device is taken through a power-on clear (for Persistent Sector Protec-

tion Mode) or the Password Unlock command is executed (for Password Sector

Protection Mode). If the Password Mode Locking Bit is set, the PPB Lock Bit status

is reflected as set, even after a power-on reset cycle.

The programming state of the PPB Lock Bit can be verified by executing a PPB

Lock Bit Status Read Command to the device.

The Global Volatile Sector Protection Freeze Command Set Exit command

must be issued after the execution of the commands listed previously to reset the

device to read mode.

Volatile Sector Protection Command Set

The Volatile Sector Protection Command Set permits the user to set the Dynamic

Protection Bit (DYB), clear the Dynamic Protection Bit (DYB), and read the logic

state of the Dynamic Protection Bit (DYB).

The Volatile Sector Protection Command Set Entry command sequence

must be issued prior to any of the following commands to enable proper com-

mand execution.

DYB Set Command

DYB Clear Command

DYB Status Read Command

Note that issuing the Volatile Sector Protection Command Set Entry com-

mand disables reads and writes for the bank selected with the command. Reads

within that bank will return the DYB status for that sector. Writes within that bank

will set the DYB for that sector. Reads for other banks excluding that bank are

allowed; writes are not allowed. All Reads must be performed using the Asyn-

chronous mode.

The DYB Set/Clear command is used to set or clear a DYB for a given sector. The

high order address bits (A23–A14 for the WS256N, A22–A14 for the WS128N,

A21–A14 for the WS064N) are issued at the same time as the code 00h or 01h

on DQ7-DQ0. All other DQ data bus pins are ignored during the data write cycle.

The DYBs are modifiable at any time, regardless of the state of the PPB or PPB

Lock Bit. The DYBs are cleared at power-up or hardware reset.

The programming state of the DYB for a given sector can be verified by writing a

DYB Status Read Command to the device.

The Volatile Sector Protection Command Set Exit command must be issued

after the execution of the commands listed previously to reset the device to read

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 73

Preliminary

mode. Note that issuing the Volatile Sector Protection Command Set Exit

command re-enables reads and writes for Bank 0.

SecSi Sector Entry Command

The SecSi Sector Entry Command allows the following commands to be executed

Read from SecSi Sector

Program to SecSi Sector

Sector 0 is remapped from memory array to SecSi Sector array. Reads can be

performed using the Asynchronous or Synchronous mode. Burst mode reads

within SecSi Sector will wrap from address FFh back to address 00h. Reads out-

side of sector 0 will return memory array data. Continuous burst read past the

maximum address is undefined.

Simultaneous operations are allowed except for Bank 0. Once the SecSi Sector

Entry Command is issued, the SecSi Sector Exit command has to be issued to exit

SecSi Sector Mode.

74 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

Command Definition Summary

Ta bl e 3 0 . Memory Array Commands

Command Sequence

(Notes)

Cycles

Bus Cycles (Notes 1–5)

First Second Third Fourth Fifth Sixth

Addr Data Addr Data Addr Data Addr Data Addr Data Addr Data

Asynchronous Read (6) 1 RA RD

Reset (7) 1 XXX F0

Auto-

select (8)

Manufacturer ID 4555 AA 2AA 55 [BA]555 90 [BA]X00 0001

Device ID (9) 6 555 AA 2AA 55 [BA]555 90 [BA]X01 227E BA+X0E Data BA+X0F 2200

Indicator Bits (10) 4 555 AA 2AA 55 [BA]555 90 [BA]X03 Data

Program 4555 AA 2AA 55 555 A0 PA PD

Write to Buffer (11) 6 555 AA 2AA 55 PA 25 PA WC PA PD WBL PD

Program Buffer to Flash 1SA 29

Write to Buffer Abort Reset (12) 3 555 AA 2AA 55 555 F0

Chip Erase 6555 AA 2AA 55 555 80 555 AA 2AA 55 555 10

Sector Erase 6555 AA 2AA 55 555 80 555 AA 2AA 55 SA 30

Erase/Program Suspend (13) 1 BA B0

Erase/Program Resume (14) 1 BA 30

Set Configuration Register (18) 4 555 AA 2AA 55 555 D0 X00 CR

Read Configuration Register 4555 AA 2AA 55 555 C6 X00 CR

CFI Query (15) 1 [BA]555 98

Unlock Bypass

Mode

Entry 3555 AA 2AA 55 555 20

Program (16) 2 XXX A0 PA PD

CFI (16) 1 XXX 98

Reset 2XXX 90 XXX 00

SecSi Sector

Entry 3555 AA 2AA 55 555 88

Program (17) 4 555 AA 2AA 55 555 A0 PA PD

Read (17) 1 00 Data

Exit (17) 4 555 AA 2AA 55 555 90 XXX 00

Legend:

X = Don’t care.

RA = Read Address.

RD = Read Data.

PA = Program Address. Addresses latch on the rising edge of the

AVD# pulse or active edge of CLK, whichever occurs first.

PD = Program Data. Data latches on the rising edge of WE# or CE#

pulse, whichever occurs first.

SA = Sector Address. WS256N = A23–A14; WS128N = A22–A14;

WS064N = A21–A14.

BA = Bank Address. WS256N = A23–A20; WS128N = A22–A20;

WS064N = A21–A18.

CR = Configuration Register data bits D15–D0.

WBL = Write Buffer Location. Address must be within the same write

buffer page as PA.

WC = Word Count. Number of write buffer locations to load minus 1.

Notes:

1. See Table 1 for description of bus operations.

2. All values are in hexadecimal.

3. Shaded cells indicate read cycles.

4. Address and data bits not specified in table, legend, or notes are

don’t cares (each hex digit implies 4 bits of data).

5. Writing incorrect address and data values or writing them in the

improper sequence may place the device in an unknown state.

The system must write the reset command to return the device

to reading array data.

6. No unlock or command cycles required when bank is reading

array data.

7. Reset command is required to return to reading array data (or to

the erase-suspend-read mode if previously in Erase Suspend)

when a bank is in the autoselect mode, or if DQ5 goes high

(while the bank is providing status information) or performing

sector lock/unlock.

8. The system must provide the bank address. See Autoselect

Command Sequence section for more information.

9. Data in cycle 5 is 2230 (WS256N), 2232 (WS064N), or 2231

(WS128N).

10. See Table 28 for indicator bit values.

11. Total number of cycles in the command sequence is determined

by the number of words written to the write buffer. The number

of cycles in the command sequence is 37 for full page

programming (32 words).

12. Command sequence resets device for next command after write-

to-buffer operation.

13. System may read and program in non-erasing sectors, or enter

the autoselect mode, when in the Erase Suspend mode. The

Erase Suspend command is valid only during a sector erase

operation, and requires the bank address.

14. Erase Resume command is valid only during the Erase Suspend

mode, and requires the bank address.

15. Command is valid when device is ready to read array data or

when device is in autoselect mode. Address will equal 55h on all

future devices, but 555h for WS256N/128N/064N.

16. Requires Entry command sequence prior to execution. Unlock

Bypass Reset command is required to return to reading array

data.

17. Requires Entry command sequence prior to execution. SecSi

Sector Exit Reset command is required to exit this mode; device

may otherwise be placed in an unknown state.

18. Requires reset command to configure the Configuration Register.

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 75

Preliminary

Table 31. Sector Protection Commands

Command Sequence

(Notes)

Cycles

Bus Cycles (Notes 1–4)

First Second Third Fourth Fifth Sixth Seventh

Addr Data Addr Data Addr Data Addr Data Addr Data Addr Data Addr Data

Lock

Bits

Command Set Entry (5) 3 555 AA 2AA 55 555 40

Program (6) 2 XX A0 77 data

Read (6) 1 77 data

Command Set Exit (7) 2 XX 90 XX 00

Password

Protection

Command Set Entry (5) 3 555 AA 2AA 55 555 60

Program [0-3] (8) 2 XX A0 00 PWD[0-3]

Read (9) 4 0...00 PWD0 0...01 PWD1 0...02 PWD2 0...03 PWD3

Unlock 7 00 25 00 03 00 PWD0 01 PWD1 02 PWD2 03 PWD3 00 29

Command Set Exit (7) 2 XX 90 XX 00

Non-Volatile

Sector

Protection (PPB)

Command Set Entry (5) 3 555 AA 2AA 55 [BA]555 C0

PPB Program (10) 2 XX A0 SA 00

All PPB Erase (10, 11) 2 XX 80 00 30

PPB Status Read 1 SA RD(0)

Command Set Exit (7) 2 XX 90 XX 00

Global

Volatile Sector

Protection

Freeze

(PPB Lock)

Command Set Entry (5) 3 555 AA 2AA 55 [BA]555 50

PPB Lock Bit Set 2 XX A0 XX 00

PPB Lock Bit Status Read 1 BA RD(0)

Command Set Exit (7) 2 XX 90 XX 00

Volatile Sector

Protection

(DYB)

Command Set Entry (5) 3 555 AA 2AA 55 [BA]555 E0

DYB Set 2 XX A0 SA 00

DYB Clear 2 XX A0 SA 01

DYB Status Read 1 SA RD(0)

Command Set Exit (7) 2 XX 90 XX 00

egen

X = Don’t care.

RA = Address of the memory location to be read.

PD(0) = SecSi Sector Lock Bit. PD(0), or bit[0].

PD(1) = Persistent Protection Mode Lock Bit. PD(1), or bit[1], must

be set to ‘0’ for protection while PD(2), bit[2] must be left as ‘1’.

PD(2) = Password Protection Mode Lock Bit. PD(2), or bit[2], must

be set to ‘0’ for protection while PD(1), bit[1] must be left as ‘1’.

PD(3) = Protection Mode OTP Bit. PD(3) or bit[3].

SA = Sector Address. WS256N = A23–A14; WS128N = A22–A14;

WS064N = A21–A14.

BA = Bank Address. WS256N = A23–A20; WS128N = A22–A20;

WS064N = A21–A18.

PWD3–PWD0 = Password Data. PD3–PD0 present four 16 bit

combinations that represent the 64-bit Password

PWA = Password Address. Address bits A1 and A0 are used to select

each 16-bit portion of the 64-bit entity.

PWD = Password Data.

RD(0), RD(1), RD(2) = DQ0, DQ1, or DQ2 protection indicator bit. If

protected, DQ0, DQ1, or DQ2 = 0. If unprotected, DQ0, DQ1,

DQ2 = 1.

Notes:

1. All values are in hexadecimal.

2. Shaded cells indicate read cycles.

3. Address and data bits not specified in table, legend, or notes are

don’t cares (each hex digit implies 4 bits of data).

4. Writing incorrect address and data values or writing them in the

improper sequence may place the device in an unknown state.

The system must write the reset command to return the device

to reading array data.

5. Entry commands are required to enter a specific mode to enable

instructions only available within that mode.

6. If both the Persistent Protection Mode Locking Bit and the

Password Protection Mode Locking Bit are set at the same time,

the command operation will abort and return the device to the

default Persistent Sector Protection Mode during 2nd bus cycle.

Note that on all future devices, addresses will equal 00h, but are

currently 77h for WS256N, WS128N, and WS064N. See Table 14

for explanation of lock bits.

7. Exit command must be issued to reset the device into read

mode; device may otherwise be placed in an unknown state.

8. Entire two bus-cycle sequence must be entered for each portion

of the password.

9. Full address range is required for reading password.

10. See Figure 5 for details.

11. “All PPB Erase” command will pre-program all PPBs before

erasure to prevent over-erasure.

76 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

Write Operation Status

The device provides several bits to determine the status of a program or erase

operation: DQ1, DQ2, DQ3, DQ5, DQ6, and DQ7. Ta b le 3 3 and the following sub-

sections describe the function of these bits. DQ7 and DQ6 each offers a method

for determining whether a program or erase operation is complete or in progress.

Please see the figure below for the general purpose data polling algorithm.

Figure 6. Polling Flow Chart

START

DQ7=valid

data?

YES

DQ5=1?

YES

Write Buffer

Programming?

YES

Device BUSY,

Re-Poll

DQ1=1?

YES

DQ1=1

AND DQ7 ≠

Valid Data?

YES

(Note 4)

Write Buffer

Operation

Failed

DQ6

toggling?

YES

TIMEOUT

(Note 1)

(Note 3)

Programming

Operation?

DQ6

toggling?

YES

DQ2

toggling?

YES

Erase

Operation

Complete

Device in

Erase/Suspend

Mode

Program

Operation

Failed

DEVICE

ERROR

Erase

Operation

Complete

Read3=

valid data?

YES

Notes:

1) DQ6 is toggling if Read2 DQ6 does not equal Read3 DQ6.

2) DQ2 is toggling if Read2 DQ2 does not equal Read3 DQ2.

3) May be due to an attempt to program a 0 to 1. Use the RESET

command to exit operation.

4) Write buffer error if DQ1 of last read =1.

5) Invalid state, use RESET command to exit operation.

6) Valid data is the data that is intended to be programmed or all 1's for

an erase operation.

7) Data polling algorithm valid for all operations except advanced sector

protection.

Device BUSY,

Re-Poll

Device BUSY,

Re-Poll

Device BUSY,

Re-Poll

(Note 1)

(Note 2)

(Note 6)

(Note 5)

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 77

Preliminary

DQ7: Data# Polling

The Data# Polling bit, DQ7, indicates to the host system whether an Embedded

Program or Erase algorithm is in progress or completed, or whether a bank is in

Erase Suspend. Data# Polling is valid after the rising edge of the final WE# pulse

in the command sequence. Note that the Data# Polling is valid only for the

last word being programmed in the write-buffer-page during Write

Buffer Programming. Reading Data# Polling status on any word other

than the last word to be programmed in the write-buffer-page will return

false status information.

During the Embedded Program algorithm, the device outputs on DQ7 the com-

plement of the datum programmed to DQ7. This DQ7 status also applies to

programming during Erase Suspend. When the Embedded Program algorithm is

complete, the device outputs the datum programmed to DQ7. The system must

provide the program address to read valid status information on DQ7. If a pro-

gram address falls within a protected sector, Data# Polling on DQ7 is active for

approximately tPSP

, then that bank returns to the read mode.

During the Embedded Erase algorithm, Data# Polling produces a “0” on DQ7.

When the Embedded Erase algorithm is complete, or if the bank enters the Erase

Suspend mode, Data# Polling produces a “1” on DQ7. The system must provide

an address within any of the sectors selected for erasure to read valid status in-

formation on DQ7.

After an erase command sequence is written, if all sectors selected for erasing

are protected, Data# Polling on DQ7 is active for approximately tASP

, then the

bank returns to the read mode. If not all selected sectors are protected, the Em-

bedded Erase algorithm erases the unprotected sectors, and ignores the selected

sectors that are protected. However, if the system reads DQ7 at an address within

a protected sector, the status may not be valid.

Just prior to the completion of an Embedded Program or Erase operation, DQ7

may change asynchronously with DQ6–DQ0 while Output Enable (OE#) is as-

serted low. That is, the device may change from providing status information to

valid data on DQ7. Depending on when the system samples the DQ7 output, it

may read the status or valid data. Even if the device has completed the program

or erase operation and DQ7 has valid data, the data outputs on DQ6-DQ0 may

be still invalid. Valid data on DQ7-D00 will appear on successive read cycles.

Tab l e 3 3 shows the outputs for Data# Polling on DQ7. Figure 7 shows the Data#

Polling algorithm. Figure 23 in “AC Characteristics—Asynchronous” shows the

Data# Polling timing diagram.

DQ6: Toggle Bit I

Toggle Bit I on DQ6 indicates whether an Embedded Program or Erase algorithm

is in progress or complete, or whether the device has entered the Erase Suspend

mode. Toggle Bit I may be read at any address in the same bank, and is valid

after the rising edge of the final WE# pulse in the command sequence (prior to

the program or erase operation), and during the sector erase time-out.

During an Embedded Program or Erase algorithm operation, successive read cy-

cles to any address cause DQ6 to toggle. When the operation is complete, DQ6

stops toggling.

After an erase command sequence is written, if all sectors selected for erasing

are protected, DQ6 toggles for approximately tASP (all sectors protected toggle

time), then returns to reading array data. If not all selected sectors are protected,

78 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

the Embedded Erase algorithm erases the unprotected sectors, and ignores the

selected sectors that are protected.

The system can use DQ6 and DQ2 together to determine whether a sector is ac-

tively erasing or is erase-suspended. When the device is actively erasing (that is,

the Embedded Erase algorithm is in progress), DQ6 toggles. When the device en-

ters the Erase Suspend mode, DQ6 stops toggling. However, the system must

also use DQ2 to determine which sectors are erasing or erase-suspended. Alter-

natively, the system can use DQ7 (see the subsection on DQ7: Data# Polling).

If a program address falls within a protected sector, DQ6 toggles for approxi-

mately tPSP after the program command sequence is written, then returns to

reading array data.

DQ6 also toggles during the erase-suspend-program mode, and stops toggling

once the Embedded Program algorithm is complete.

See the following for additional information: Figure 8, DQ6: Toggle Bit I, Figure

24 (toggle bit timing diagram), and Table 32.

Toggle Bit I on DQ6 requires either OE# or CE# to be deasserted and reasserted

to show the change in state.

DQ2: Toggle Bit II

The “Toggle Bit II” on DQ2, when used with DQ6, indicates whether a particular

sector is actively erasing (that is, the Embedded Erase algorithm is in progress),

or whether that sector is erase-suspended. Toggle Bit II is valid after the rising

edge of the final WE# pulse in the command sequence.

DQ2 toggles when the system reads at addresses within those sectors that have

been selected for erasure. But DQ2 cannot distinguish whether the sector is ac-

tively erasing or is erase-suspended. DQ6, by comparison, indicates whether the

device is actively erasing, or is in Erase Suspend, but cannot distinguish which

sectors are selected for erasure. Thus, both status bits are required for sector and

mode information. Refer to Ta b l e 32 to compare outputs for DQ2 and DQ6.

See the following for additional information: Figure 8; DQ6: Toggle Bit I; and Fig-

ure 24.

Ta bl e 3 2 . DQ6 and DQ2 Indications

If device is and the system reads then DQ6 and DQ2

programming, at any address, toggles, does not toggle.

actively erasing,

at an address within a sector

selected for erasure, toggles, also toggles.

at an address within sectors not

selected for erasure, toggles, does not toggle.

erase suspended,

at an address within a sector

selected for erasure, does not toggle, toggles.

at an address within sectors not

selected for erasure, returns array data, returns array data. The system can read

from any sector not selected for erasure.

programming in

erase suspend at any address, toggles, is not applicable.

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 79

Preliminary

Reading Toggle Bits DQ6/DQ2

Whenever the system initially begins reading toggle bit status, it must read DQ7–

DQ0 at least twice in a row to determine whether a toggle bit is toggling. Typi-

cally, the system would note and store the value of the toggle bit after the first

read. After the second read, the system would compare the new value of the tog-

gle bit with the first. If the toggle bit is not toggling, the device has completed

the program or erase operation. The system can read array data on DQ7–DQ0 on

the following read cycle.

However, if after the initial two read cycles, the system determines that the toggle

bit is still toggling, the system also should note whether the value of DQ5 is high

(see the section on DQ5). If it is, the system should then determine again

whether the toggle bit is toggling, since the toggle bit may have stopped toggling

just as DQ5 went high. If the toggle bit is no longer toggling, the device has suc-

cessfully completed the program or erase operation. If it is still toggling, the

device did not completed the operation successfully, and the system must write

the reset command to return to reading array data.

The remaining scenario is that the system initially determines that the toggle bit

is toggling and DQ5 has not gone high. The system may continue to monitor the

toggle bit and DQ5 through successive read cycles, determining the status as de-

scribed in the previous paragraph. Alternatively, it may choose to perform other

system tasks. In this case, the system must start at the beginning of the algo-

rithm when it returns to determine the status of the operation. Refer to Figure 8

for more details.

DQ5: Exceeded Timing Limits

DQ5 indicates whether the program or erase time has exceeded a specified inter-

nal pulse count limit. Under these conditions DQ5 produces a “1,” indicating that

the program or erase cycle was not successfully completed.

The device may output a “1” on DQ5 if the system tries to program a “1” to a

location that was previously programmed to “0.” Only an erase operation can

change a “0” back to a “1.” Under this condition, the device halts the operation,

and when the timing limit has been exceeded, DQ5 produces a “1.”

Under both these conditions, the system must write the reset command to return

to the read mode (or to the erase-suspend-read mode if a bank was previously

in the erase-suspend-program mode).

DQ3: Sector Erase Start Timeout State Indicator

After writing a sector erase command sequence, the system may read DQ3 to de-

termine whether or not erasure has begun. (The sector erase start timeout state

indicator does not apply to the chip erase command.) If additional sectors are se-

lected for erasure, the entire time-out also applies after each additional sector

erase command. When the time-out period is complete, DQ3 switches from a “0”

to a “1.” If the time between additional sector erase commands from the system

can be assumed to be less than tSEA, the system need not monitor DQ3. See Sec-

tor Erase Command Sequence for more details.

After the sector erase command is written, the system should read the status of

DQ7 (Data# Polling) or DQ6 (Toggle Bit I) to ensure that the device has accepted

the command sequence, and then read DQ3. If DQ3 is “1,” the Embedded Erase

algorithm has begun; all further commands (except Erase Suspend) are ignored

until the erase operation is complete. If DQ3 is “0,” the device will accept addi-

80 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

tional sector erase commands. To ensure the command has been accepted, the

system software should check the status of DQ3 prior to and following each sub-

sequent sector erase command. If DQ3 is high on the second status check, the

last command might not have been accepted.

Tab l e 3 3 shows the status of DQ3 relative to the other status bits.

DQ1: Write to Buffer Abort

DQ1 indicates whether a Write to Buffer operation was aborted. Under these con-

ditions DQ1 produces a ‘1’. The system must issue the Write to Buffer Abort Reset

command sequence to return the device to reading array data. See Write Buffer

Programming Operation for more details.

Table 33. Write Operation Status

Notes:

1. DQ5 switches to ‘1’ when an Embedded Program or Embedded Erase operation has exceeded the maximum

timing limits. Refer to the section on DQ5 for more information.

2. DQ7 and DQ2 require a valid address when reading status information. Refer to the appropriate subsection

for further details.

3. Data are invalid for addresses in a Program Suspended sector.

4. DQ1 indicates the Write to Buffer ABORT status during Write Buffer Programming operations.

5. The data-bar polling algorithm should be used for Write Buffer Programming operations. Note that DQ7#

during Write Buffer Programming indicates the data-bar for DQ7 data for the LAST LOADED WRITE-

BUFFER ADDRESS location.

Status

DQ7

(Note 2) DQ6

DQ5

(Note 1) DQ3

DQ2

(Note 2)

DQ1

(Note 4)

Standard

Mode

Embedded Program Algorithm

DQ7# Toggle 0N/A No toggle 0

Embedded Erase Algorithm 0Toggle 0 1 Toggle N/A

Program

Suspend

Mode

(Note 3)

Reading within Program Suspended

Sector

INVALID

(Not

Allowed)

INVALID

(Not

Allowed)

INVALID

(Not

Allowed)

INVALID

(Not

Allowed)

INVALID

(Not

Allowed)

INVALID

(Not

Allowed)

Reading within Non-Program

Suspended Sector Data Data Data Data Data Data

Erase

Suspend

Mode

Erase-Suspend-

Read

Erase

Suspended Sector 1No toggle 0N/A Toggle N/A

Non-Erase

Suspended Sector Data Data Data Data Data Data

Erase-Suspend-Program DQ7# Toggle 0N/A N/A N/A

Write to

Buffer

(Note 5)

BUSY State DQ7# Toggle 0N/A N/A 0

Exceeded Timing Limits DQ7# Toggle 1N/A N/A 0

ABORT State DQ7# Toggle 0N/A N/A 1

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 81

Preliminary

Absolute Maximum Ratings

Storage Temperature

Plastic Packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .–65°C to +150°C

Ambient Temperature

with Power Applied . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .–65°C to +125°C

Voltage with Respect to Ground:

All Inputs and I/Os except

as noted below (Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to VIO + 0.5 V

VCC (Note 1). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to +2.5 V

VIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to +2.5 V

ACC (Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to +9.5 V

Output Short Circuit Current (Note 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 mA

Notes:

1. Minimum DC voltage on input or I/Os is –0.5 V. During voltage transitions, inputs or

I/Os may undershoot VSS to –2.0 V for periods of up to 20 ns. See Figure 7. Maximum

DC voltage on input or I/Os is VCC + 0.5 V. During voltage transitions outputs may

overshoot to VCC + 2.0 V for periods up to 20 ns. See Figure 8.

2. Minimum DC input voltage on pin ACC is -0.5V. During voltage transitions, ACC may

overshoot VSS to –2.0 V for periods of up to 20 ns. See Figure 7. Maximum DC voltage

on pin ACC is +9.5 V, which may overshoot to 10.5 V for periods up to 20 ns.

3. No more than one output may be shorted to ground at a time. Duration of the short

circuit should not be greater than one second.

4. Stresses above those listed under “Absolute Maximum Ratings” may cause permanent

damage to the device. This is a stress rating only; functional operation of the device at

these or any other conditions above those indicated in the operational sections of this

data sheet is not implied. Exposure of the device to absolute maximum rating conditions

for extended periods may affect device reliability.

Operating Ranges

Wireless (W) Devices

Ambient Temperature (TA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –25°C to +85°C

Industrial (I) Devices

Ambient Temperature (TA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –40°C to +85°C

Supply Voltages

VCC Supply Voltages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +1.70 V to +1.95 V

VIO Supply Voltages: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +1.70 V to +1.95 V

(Contact local sales office for VIO = 1.35 to +1.70 V.)

Notes: Operating ranges define those limits between which the functionality of the device

is guaranteed.

Figure 7. Maximum Negative Overshoot

Waveform

Figure 8. Maximum Positive Overshoot

Waveform

20 ns

+0.8 V

–0.5 V

20 ns

–2.0 V

20 ns

+2.0 V

+0.5 V

20 ns

1.0 V

82 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

DC Characteristics

CMOS Compatible

Notes:

1. Maximum ICC specifications are tested with VCC = VCCmax.

2. VCC= VIO.

3. CE# must be set high when measuring the RDY pin.

4. The ICC current listed is typically less than 3 mA/MHz, with OE# at VIH.

5. ICC active while Embedded Erase or Embedded Program is in progress.

6. Device enters automatic sleep mode when addresses are stable for tACC + 20 ns. Typical sleep mode current is equal to ICC3.

7. VIH = VCC ± 0.2 V and VIL > –0.1 V.

8. Total current during accelerated programming is the sum of VACC and VCC currents.

9. VACC = VHH on ACC input.

Parameter Description (Notes) Test Conditions (Notes 1, 2, 9) Min Ty p Max Unit

ILI Input Load Current VIN = VSS to VCC, VCC = VCCmax ±1 µA

ILO Output Leakage Current (3) VOUT = VSS to VCC, VCC = VCCmax ±1 µA

ICCB VCC Active burst Read Current

CE# = VIL, OE# = VIH, WE#

= VIH, burst length = 8

54 MHz 27 54 mA

66 MHz 28 60 mA

80 MHz 30 66 mA

CE# = VIL, OE# = VIH, WE#

= VIH, burst length = 16

54 MHz 28 48 mA

66 MHz 30 54 mA

80 MHz 32 60 mA

CE# = VIL, OE# = VIH, WE#

= VIH, burst length = 32

54 MHz 29 42 mA

66 MHz 32 48 mA

80 MHz 34 54 mA

CE# = VIL, OE# = VIH, WE#

= VIH, burst length =

Continuous

54 MHz 32 36 mA

66 MHz 35 42 mA

80 MHz 38 48 mA

IIO1 VIO Non-active Output OE# = VIH 20 30 µA

ICC1 VCC Active Asynchronous Read Current

(4)

CE# = VIL, OE# = VIH, WE#

= VIH

10 MHz 27 36 mA

5 MHz 13 18 mA

1 MHz 3 4 mA

ICC2 VCC Active Write Current (5) CE# = VIL, OE# = VIH, ACC

= VIH

VACC 15µA

VCC 19 52.5 mA

ICC3 VCC Standby Current (6, 7) CE# = RESET# =

VCC ± 0.2 V

VACC 15µA

VCC 20 40 µA

ICC4 VCC Reset Current (7) RESET# = VIL, CLK = VIL 70 150 µA

ICC5 VCC Active Current (Read While Write) (7) CE# = VIL, OE# = VIH, ACC = VIH 50 60 mA

ICC6 VCC Sleep Current (7) CE# = VIL, OE# = VIH 240µA

IACC Accelerated Program Current (8) CE# = VIL, OE# = VIH,

VACC = 9.5 V

VACC 620mA

VCC 14 20 mA

VIL Input Low Voltage VIO = 1.8 V –0.5 0.4 V

VIH Input High Voltage VIO = 1.8 V VIO – 0.4 VIO + 0.4 V

VOL Output Low Voltage IOL = 100 µA, VCC = VCC min = VIO 0.1 V

VOH Output High Voltage IOH = –100 µA, VCC = VCC min = VIO VIO – 0.1 V

VHH Voltage for Accelerated Program 8.5 9.5 V

VLKO Low VCC Lock-out Voltage 1.0 1.4 V

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 83

Preliminary

Test Conditions

Ta b le 3 4. Test Specifications

Key to Switching Waveforms

Switching Waveforms

Test Condition All Speed Options Unit

Output Load Capacitance, C

(including jig capacitance) 30 pF

Input Rise and Fall Times 3.0 @ 54, 66 MHz

2.5 @ 80 MHz ns

Input Pulse Levels 0.0–V

Input timing measurement

reference levels V

/2 V

Output timing measurement

reference levels V

/2 V

Device

Under

Test

Figure 9. Test Setup

WAVEFORM INPUTS OUTPUTS

Steady

Changing from H to L

Changing from L to H

Don’t Care, Any Change Permitted Changing, State Unknown

Does Not Apply Center Line is High Impedance State (High Z)

Figure 10. Input Waveforms and Measurement Levels

0.0 V OutputMeasurement LevelInput V

/2 V

ll Inputs and Outputs

84 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

VCC Power-up

Note:

1. The ramp rate must be greater than 1 V/200 µs and VCC ≥ VIO-100 mV.

2. If the ramp rate is less than 1 V/200 µs, then a Hardware Reset will be required.

Figure 11. VCC Power-up Diagram

Parameter Description Te s t S e t u p Speed Unit

VCS

Setup Time Min 1ms

VCC

VIO

ESET#

tVCS

tVIOS

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 85

Preliminary

AC Characteristics—Synchronous

CLK Characterization

Figure 12. CLK Characterization

Parameter Description 54 MHz 66 MHz 80 MHz Unit

CLK

CLK Frequency Max 54 66 80 MHz

CLK

CLK Period Min 18.5 15.1 12.5 ns

CLK High Time

Min 7.4 6.1 5.0 ns

CLK Low Time

CLK Rise Time

Max 3 3 2.5 ns

CLK Fall Time

tCLK

tCL

tCH

tCR tCF

CLK

86 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

Synchronous/Burst Read

Notes:

1. Addresses are latched on the first of either the active edge of CLK or the rising edge of AVD#.

2. Not 100% tested.

Parameter

Description 54 MHz 66 MHz 80 MHz UnitJEDEC Standard

IACC

Latency Max 69 ns

BACC

Burst Access Time Valid Clock to Output Delay Max 13.5 11.2 9ns

ACS

Address Setup Time to CLK (Note 1) Min 5 4 ns

ACH

Address Hold Time from CLK (Note 1) Min 7 6 ns

BDH

Data Hold Time from Next Clock Cycle Min 4 3 ns

Chip Enable to RDY Valid Max 13.5 11.2 9ns

Output Enable to Output Valid Max 13.5 11.2 ns

CEZ

Chip Enable to High Z (Note 2) Max 10 ns

OEZ

Output Enable to High Z (Note 2) Max 10 ns

CES

CE# Setup Time to CLK Min 4ns

RDYS

RDY Setup Time to CLK Min 5 4 3.5 ns

RACC

Ready Access Time from CLK Max 13.5 11.2 9ns

AAS

Address Setup Time to AVD# (Note 1) Min 5 4 ns

AAH

Address Hold Time to AVD# (Note 1) Min 7 6 ns

CAS

CE# Setup Time to AVD# Min 0ns

AVC

AVD# Low to CLK Min 4ns

AVD

AVD# Pulse Min 8ns

AOE

AVD# Low to OE# Low Max 38.4 ns

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 87

Preliminary

Timing Diagrams

Notes:

1. Figure shows total number of wait states set to five cycles. The total number of wait states can be

programmed from two cycles to seven cycles.

2. If any burst address occurs at “address + 1”, “address + 2”, or “address + 3”, additional clock delay cycles

are inserted, and are indicated by RDY.

3. The device is in synchronous mode.

Figure 13. CLK Synchronous Burst Mode Read

Da Da + 1 Da + n

OE#

Data (n)

Addresses

AVD#

RDY (n)

CLK

CE#

CES

ACS

AVC

AVD

ACH

RACC

OEZ

CEZ

IACC

AOE

BDH

5 cycles for initial access shown.

18.5 ns typ. (54 MHz)

Hi-Z

Hi-Z Hi-Z

12 3456 7

RDYS

BACC

Da + 3

Da + 2

Da Da + 1 Da + n

Data (n + 1)

RDY (n + 1)

Hi-Z

Hi-Z Hi-Z

Da + 2

Da Da + 1 Da + n

Data (n + 2)

RDY (n + 2)

Hi-Z

Hi-Z Hi-Z

Da + 1

Da Da Da + n

Data (n + 3)

RDY (n + 3)

Hi-Z

Hi-Z Hi-Z

88 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

Notes:

1. Figure shows total number of wait states set to seven cycles. The total number of wait states can be programmed from two cycles to seven

cycles. Clock is set for active rising edge.

2. If any burst address occurs at “address + 1”, “address + 2”, or “address + 3”, additional clock delay cycles are inserted, and are indicated

by RDY.

3. The device is in synchronous mode with wrap around.

4. D8–DF in data waveform indicate the order of data within a given 8-word address range, from lowest to highest. Starting address in figure

is the 4th address in range (0-F).

Figure 14. 8-word Linear Burst with Wrap Around

Notes:

1. Figure shows total number of wait states set to seven cycles. The total number of wait states can be programmed from two cycles to seven

cycles. Clock is set for active rising edge.

2. If any burst address occurs at “address + 1”, “address + 2”, or “address + 3”, additional clock delay cycles are inserted, and are indicated

by RDY.

3. The device is in asynchronous mode with out wrap around.

4. DC–D13 in data waveform indicate the order of data within a given 8-word address range, from lowest to highest. Starting address in figure

is the 1st address in range (c-13).

Figure 15. 8-word Linear Burst without Wrap Around

DC DD

OE#

Data

Addresses

AVD#

RDY

CLK

CE#

CES

ACS

AVC

AVD

ACH

IACC

AOE

BDH

DE DF DB

7 cycles for initial access shown.

Hi-Z

RACC

1234567

RDYS

BACC

RACC

DC DD

OE#

Data

Addresses

AVD#

RDY

CLK

CE#

CES

ACS

AVC

AVD

ACH

IACC

BDH

DE DF DB

7 cycles for initial access shown.

Hi-Z

RACC

1234567

RDYS

BACC

RACC

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 89

Preliminary

Notes:

1. Figure assumes 6 wait states for initial access and synchronous read.

2. The Set Configuration Register command sequence has been written with CR8=0; device will output RDY one

cycle before valid data.

Figure 16. Linear Burst with RDY Set One Cycle Before Data

Da+1Da Da+2 Da+3 Da + n

OE#

Data

Addresses

AVD#

RDY

CLK

CE#

CES

ACS

AVC

AVD

ACH

RACC

OEZ

CEZ

IACC

AOE

BDH

6 wait cycles for initial access shown.

Hi-Z

Hi-Z Hi-Z

123456

RDYS

BACC

90 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

AC Characteristics—Asynchronous

Asynchronous Mode Read

Note: Not 100% tested.

Timing Diagrams

Note:

RA = Read Address, RD = Read Data.

Figure 17. Asynchronous Mode Read with Latched Addresses

Parameter

Description 54 MHz 66 MHz 80 MHz UnitJEDEC Standard

Access Time from CE# Low Max 70 ns

ACC

Asynchronous Access Time Max 70 ns

AVDP

AVD# Low Time Min 8ns

AAVDS

Address Setup Time to Rising Edge of AVD# Min 4ns

AAVDH

Address Hold Time from Rising Edge of AVD# Min 7 6 ns

Output Enable to Output Valid Max 13.5 11.2 ns

OEH

Output Enable Hold Time

Read Min 0ns

Toggle and Data# Polling Min 10 ns

OEZ

Output Enable to High Z (see Note) Max 10 ns

CAS

CE# Setup Time to AVD# Min 0ns

WE#

Addresses

CE#

OE#

Valid RD

ACC

OEH

Data

OEZ

AAVDH

AVDP

AAVDS

AVD#

CAS

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 91

Preliminary

Note: RA = Read Address, RD = Read Data.

Figure 18. Asynchronous Mode Read

Hardware Reset (RESET#)

Note: Not 100% tested.

Figure 19. Reset Timings

Parameter

Description All Speed Options UnitJEDEC Std.

RESET# Pulse Width Min 30 µs

Reset High Time Before Read (See Note) Min 200 ns

WE#

Addresses

CE#

OE#

Valid RD

ACC

OEH

Data

OEZ

AVD#

RESET#

tRP

CE#, OE#

tRH

92 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

Erase/Program Timing

Notes:

1. Not 100% tested.

2. Asynchronous read mode allows Asynchronous program operation only. Synchronous read mode allows both Asynchronous and

Synchronous program operation.

3. In asynchronous program operation timing, addresses are latched on the falling edge of WE#. In synchronous program operation timing,

addresses are latched on the rising edge of CLK.

4. See the “Erase and Programming Performance” section for more information.

5. Does not include the preprogramming time.

Parameter

Description 54 MHz 66 MHz 80 MHz UnitJEDEC Standard

tAVAV tWC Write Cycle Time (Note 1) Min 70 ns

tAVWL tAS Address Setup Time (Notes 2, 3) Synchronous Min 5ns

Asynchronous 0ns

tWLAX tAH Address Hold Time (Notes 2, 3) Synchronous Min 9ns

Asynchronous 20

tAVDP AVD# Low Time Min 8 ns

tDVWH tDS Data Setup Time Min 45 20 ns

tWHDX tDH Data Hold Time Min 0 ns

tGHWL tGHWL Read Recovery Time Before Write Min 0 ns

tCAS CE# Setup Time to AVD# Min 0 ns

tWHEH tCH CE# Hold Time Min 0 ns

tWLWH tWP Write Pulse Width Min 30 ns

tWHWL tWPH Write Pulse Width High Min 20 ns

tSR/W Latency Between Read and Write Operations Min 0 ns

tVID VACC Rise and Fall Time Min 500 ns

tVIDS VACC Setup Time (During Accelerated Programming) Min 1 µs

tVCS VCC Setup Time Min 50 µs

tELWL tCS CE# Setup Time to WE# Min 5 ns

tAVSW AVD# Setup Time to WE# Min 5 ns

tAVHW AVD# Hold Time to WE# Min 5 ns

tAVSC AVD# Setup Time to CLK Min 5 ns

tAVHC AVD# Hold Time to CLK Min 5 ns

tCSW Clock Setup Time to WE# Min 5 ns

tWEP Noise Pulse Margin on WE# Max 3 ns

tSEA Sector Erase Accept Time-out Max 50 µs

tESL Erase Suspend Latency Max 20 µs

tPSL Program Suspend Latency Max 20 µs

tASP Toggle Time During Sector Protection Typ 1 00 µs

tPSP Toggle Time During Programming Within a Protected Sector Typ 1 µ s

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 93

Preliminary

Notes:

1. PA = Program Address, PD = Program Data, VA = Valid Address for reading status bits.

2. “In progress” and “complete” refer to status of program operation.

3. A23–A14 for the WS256N (A22–A14 for the WS128N, A21–A14 for the WS064N) are don’t care during

command sequence unlock cycles.

4. CLK can be either VIL or VIH.

5. The Asynchronous programming operation is independent of the Set Device Read Mode bit in the

Configuration Register.

Figure 20. Asynchronous Program Operation Timings: WE# Latched Addresses

OE#

CE#

Data

Addresses

AVD#

WE#

CLK

VCC

555h

tAS

tAVSW

tAVHW

tAH

tWC

tWPH

tVCS

tWP

tDH

tCH

Progress

tWHWH1

Complete

Program Command Sequence (last two cycles) Read Status Data

tDS

VIH

VIL

tAVDP

A0h

tCS

tCAS

94 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

Notes:

1. PA = Program Address, PD = Program Data, VA = Valid Address for reading status bits.

2. “In progress” and “complete” refer to status of program operation.

3. A23–A14 for the WS256N (A22–A14 for the WS128N, A21–A14 for the WS064N) are don’t care during

command sequence unlock cycles.

4. Addresses are latched on the first of either the rising edge of AVD# or the active edge of CLK.

5. Either CE# or AVD# is required to go from low to high in between programming command sequences.

6. The Synchronous programming operation is dependent of the Set Device Read Mode bit in the Configuration

Figure 21. Synchronous Program Operation Timings: CLK Latched Addresses

OE#

CE#

Data

Addresses

AVD

WE#

CLK

555h

WPH

VCS

Progress

WHWH1

Complete

Program Command Sequence (last two cycles) Read Status Data

AVDP

A0h

CAS

AVCH

CSW

AVSC

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 95

Preliminary

Note: Use setup and hold times from conventional program operation.

Figure 22. Accelerated Unlock Bypass Programming Timing

Notes:

1. Status reads in figure are shown as asynchronous.

2. VA = Valid Address. Two read cycles are required to determine status. When the Embedded Algorithm operation is complete, and Data#

Polling will output true data.

Figure 23. Data# Polling Timings

(During Embedded Algorithm)

CE#

AVD#

WE#

Addresses

Data

OE#

ACC

Don't Care Don't CareA0h Don't Care

VID

VIL or VIH

tVID

tVIDS

WE#

CE#

OE#

High Z

Addresses

AVD#

OEH

OEZ

CEZ

Status Data Status Data

ACC

VA VA

Data

96 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

Notes:

1. Status reads in figure are shown as asynchronous.

2. VA = Valid Address. Two read cycles are required to determine status. When the Embedded Algorithm operation is complete, the toggle bits

will stop toggling.

Figure 24. To g g l e B i t T i m i n g s

(During Embedded Algorithm)

Notes:

1. The timings are similar to synchronous read timings.

2. VA = Valid Address. Two read cycles are required to determine status. When the Embedded Algorithm operation is complete, the toggle bits

will stop toggling.

3. RDY is active with data (D8 = 1 in the Configuration Register). When D8 = 0 in the Configuration Register, RDY is active one clock cycle before

data.

Figure 25. Synchronous Data Polling Timings/

Toggle Bit Timings

WE#

CE#

OE#

High Z

Addresses

AVD#

OEH

OEZ

CEZ

Status Data Status Data

ACC

VA VA

Data

VD#

ddresses

ata

Status Data Status Data

VA VA

tIACC tIACC

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 97

Preliminary

Notes:

1. RDY active with data (D8 = 1 in the Configuration Register).

2. RDY active one clock cycle before data (D8 = 0 in the Configuration Register).

3. Cxx indicates the clock that triggers Dxx on the outputs; for example, C60 triggers D60.

4. Figure shows the device not crossing a bank in the process of performing an erase or program.

5. RDY will not go low and no additional wait states will be required if the Burst frequency is <=66 MHz and the

Boundary Crossing bit (D14) in the Configuration Register is set to 0

Figure 27. Latency with Boundary Crossing when Frequency > 66 MHz

Note: DQ2 toggles only when read at an address within an erase-suspended sector. The system may use OE# or CE#

to toggle DQ2 and DQ6.

Figure 26. DQ2 vs. DQ6

Enter

Erase

Enter Erase

Suspend Program

Erase Suspend

Read Erase Suspend

Read

Erase

WE#

DQ6

DQ2

Erase

Complete

Erase

Suspend

Program

Resume

Embedded

Erasing

CLK

Address (hex)

C124 C125 C126 C127 C127 C128 C129 C130 C131

D124 D125 D126 D127 D128 D129 D130

(stays high)

AVD#

RDY(1)

Data

OE#,

CE# (stays low)

Address boundary occurs every 128 words, beginning at address

00007Fh: (0000FFh, 00017Fh, etc.) Address 000000h is also a boundary crossing.

7C 7D 7E 7F 7F 80 81 82 83

latency

RDY(2) latency

tRACC tRACC

tRACC

98 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

Notes:

1. RDY active with data (D8 = 1 in the Configuration Register).

2. RDY active one clock cycle before data (D8 = 0 in the Configuration Register).

3. Cxx indicates the clock that triggers Dxx on the outputs; for example, C60 triggers D60.

4. Figure shows the device crossing a bank in the process of performing an erase or program.

5. RDY will not go low and no additional wait states will be required if the Burst frequency is <=66 MHz and the

Boundary Crossing bit (D14) in the Configuration Register is set to 0

Figure 28. Latency with Boundary Crossing into Program/Erase Bank

CLK

ddress (hex)

C124 C125 C126 C127 C127

D124 D125 D126 D127 Read Status

(stays high)

AVD#

RDY(1)

Data

OE#,

CE# (stays low)

Address boundary occurs every 128 words, beginning at address

00007Fh: (0000FFh, 00017Fh, etc.) Address 000000h is also a boundary crossin

7C 7D 7E 7F 7F

latency

RDY(2)

latency

RACC

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 99

Preliminary

Wait State Configuration Register Setup:

D13, D12, D11 = “111” ⇒ Reserved

D13, D12, D11 = “110” ⇒ Reserved

D13, D12, D11 = “101” ⇒ 5 programmed, 7 total

D13, D12, D11 = “100” ⇒ 4 programmed, 6 total

D13, D12, D11 = “011” ⇒ 3 programmed, 5 total

D13, D12, D11 = “010” ⇒ 2 programmed, 4 total

D13, D12, D11 = “001” ⇒ 1 programmed, 3 total

D13, D12, D11 = “000” ⇒ 0 programmed, 2 total

Note: Figure assumes address D0 is not at an address boundary, and wait state is set to “101”.

Figure 29. Example of Wait States Insertion

Data

VD#

OE#

CLK

12345

D0 D

total number of clock cycles

following addresses being latched

Rising edge of next clock cycle

following last wait state triggers

next burst data

number of clock cycles

programmed

100 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

Note: Breakpoints in waveforms indicate that system may alternately read array data from the “non-busy bank” while

checking the status of the program or erase operation in the “busy” bank. The system should read status twice to ensure

valid information.

Figure 30. Back-to-Back Read/Write Cycle Timings

OE#

CE#

WE#

tOEH

Data

ddresses

AVD#

PD/30h AAh

PA/SA

tWC

tDS tDH

tRC tRC

tOE

tAS

tAH

tACC

tOEH

tWP

tGHWL

tOEZ

tWC

tSR/W

Last Cycle in

Program or

Sector Erase

Command Sequence

Read status (at least two cycles) in same bank

and/or array data from other bank Begin another

write or program

command sequence

RA 555h

tWPH

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 101

Preliminary

Erase and Programming Performance

Notes:

1. Typical program and erase times assume the following conditions: 25°C, 1.8 V VCC, 10,000 cycles;

checkerboard data pattern.

2. Under worst case conditions of 90°C, VCC = 1.70 V, 100,000 cycles.

3. The typical chip programming time is considerably less than the maximum chip programming time listed.

Based upon single word programming, not page programming.

4. In the pre-programming step of the Embedded Erase algorithm, all words are programmed to 00h before

erasure.

5. System-level overhead is the time required to execute the two- or four-bus-cycle sequence for the program

command. See Command Definition Summary for further information on command definitions.

6. Contact the local sales office for minimum cycling endurance values in specific applications and operating

conditions.

7. Refer to Application Note “Erase Suspend/Resume Timing” for more details.

8. Word programming specification is based upon a single word programming operation not utilizing the write

buffer.

Parameter

Ty p (Note 1) Max (Note 2) Unit Comments

Sector Erase Time

64 Kword V

0.6 3.5

Excludes 00h

programming prior to

erasure (Note 4)

16 Kword V

<0.15 2

Chip Erase Time

153.6 (WS256N)

77.4 (WS128N)

39.3 (WS064N)

308 (WS256N)

154 (WS128N)

78 (WS064N)

ACC

130.6 (WS256N)

65.8 (WS128N)

33.4 (WS064N)

262 (WS256N)

132 (WS128N)

66 (WS064N)

Single Word Programming Time

(Note 8)

40 400

µs

ACC 24 240

Effective Word Programming Time

utilizing Program Write Buffer

9.4 94

µs

ACC 660

Total 32-Word Buffer

Programming Time

300 3000

µs

ACC 192 1920

Chip Programming Time (Note 3)

157.3 (WS256N)

78.6 (WS128N)

39.3 (WS064N)

314.6 (WS256N)

157.3 (WS128N)

78.6 (WS064N)

sExcludes system level

overhead (Note 5)

ACC

100.7 (WS256N)

50.3 (WS128N)

25.2 (WS064N)

201.3 (WS256N)

100.7 (WS128N)

50.3 (WS064N)

102 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

BGA Ball Capacitance

Notes:

1.Sampled, not 100% tested.

2.Test conditions TA = 25°C; f = 1.0 MHz.

Parameter

Symbol Parameter Description Te s t S e t u p Ty p Max Unit

Input Capacitance V

= 0 5.3 6.3 pF

OUT

Output Capacitance V

OUT

= 0 5.8 6.8 pF

IN2

Control Pin Capacitance V

= 0 6.3 7.3 pF

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 103

Preliminary

Physical Dimensions (256 Mb and 128 Mb)

VBH084—84-ball Fine-Pitch Ball Grid Array (FBGA)

8 x 11.6 mm MCP Compatible Package

Note: BSC is an ANSI standard for Basic Space Centering

3339 \ 16-038.25

NOTES:

1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M-1994.

2. ALL DIMENSIONS ARE IN MILLIMETERS.

3. BALL POSITION DESIGNATION PER JESD 95-1, SPP-010 (EXCEP

AS NOTED).

4. e REPRESENTS THE SOLDER BALL GRID PITCH.

5. SYMBOL "MD" IS THE BALL ROW MATRIX SIZE IN THE

"D" DIRECTION.

SYMBOL "ME" IS THE BALL COLUMN MATRIX SIZE IN THE

"E" DIRECTION.

N IS THE TOTAL NUMBER OF SOLDER BALLS.

6 DIMENSION "b" IS MEASURED AT THE MAXIMUM BALL

DIAMETER IN A PLANE PARALLEL TO DATUM C.

7 SD AND SE ARE MEASURED WITH RESPECT TO DATUMS

A AND B AND DEFINE THE POSITION OF THE CENTER

SOLDER BALL IN THE OUTER ROW.

WHEN THERE IS AN ODD NUMBER OF SOLDER BALLS IN

THE OUTER ROW PARALLEL TO THE D OR E DIMENSION,

RESPECTIVELY, SD OR SE = 0.000.

WHEN THERE IS AN EVEN NUMBER OF SOLDER BALLS IN

THE OUTER ROW, SD OR SE = e/2

8. NOT USED.

9. "+" INDICATES THE THEORETICAL CENTER OF DEPOPULATED

BALLS.

10 A1 CORNER TO BE IDENTIFIED BY CHAMFER, LASER OR INK

MARK, METALLIZED MARK INDENTATION OR OTHER MEANS.

PACKAGE VBH 084

JEDEC N/A

11.60 mm x 8.00 mm NOM

PACKAGE

SYMBOL MIN NOM MAX NOTE

A --- --- 1.00 OVERALL THICKNESS

A1 0.18 --- --- BALL HEIGHT

A2 0.62 --- 0.76 BODY THICKNESS

D 11.60 BSC. BODY SIZE

E 8.00 BSC. BODY SIZE

D1 8.80 BSC. BALL FOOTPRINT

E1 7.20 BSC. BALL FOOTPRINT

MD 12 ROW MATRIX SIZE D DIRECTION

ME 10 ROW MATRIX SIZE E DIRECTION

N 84 TOTAL BALL COUNT

φb 0.33 --- 0.43 BALL DIAMETER

e 0.80 BSC. BALL PITCH

SD / SE 0.40 BSC. SOLDER BALL PLACEMENT

(A2-A9, B10-L10, DEPOPULATED SOLDER BALLS

M2-M9, B1-L1)

BOTTOM VIEW

TOP VIEW

SIDE VIEW

A1 CORNER

ML JK

C0.05

(2X)

(2X) C0.05

BACEDFHG

BCA

φ 0.15

φ 0.08 M

0.10 C

C0.08

NXφb

SEATING PLANE

A1 CORNER

INDEX MARK

104 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

Physical Dimensions (64 Mb)

TBD—80-ball Fine-Pitch Ball Grid Array (FBGA) 7x9 mm MCP Compatible Package

Note: BSC is an ANSI standard for Basic Space Centering

TBD

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 105

Preliminary

Revision Summary

Revision A (February 2, 2004)

Initial release.

Revision A + 1 (March 12, 2004)

Performance Characteristics

Removed the Clock Divider section.

Security Features

Removed Burst Suspend/Resume section. Removed all document-wide refer-

ences to this feature.

Ordering Information

Package type designations were corrected to show proper lead (Pb)

characteristics.

Process Technology was corrected to 110nm.

Word Program Command Sequence

New information added. Section completely re-written.

Revision B (May 24, 2004)

Global

Changed document status to Preliminary. Deleted references to 1.5 V VIO option.

Distinctive Characteristics

MCP-Compatible Packages: Changed ball count and dimensions for 128Mb BGA

package to 84-ball, 8 x 11.6 mm.

High Performance: Changed typical word programming time to <6 µs.

General Description

Corrected maximum wireless temperature range maximum to +85°C. Deleted

paragraph referring to clock polarity.

Connection Diagrams

Changed diagram for 128 Mb package to 84-ball layout, changed A23 input to

RFU. Added note to 64 Mb connection diagram.

Ordering Information

Changed valid combinations for 128 Mb density to match package change (80-

ball to 84-ball; 8 x 10 mm to 8 x 11.6 mm).

Table 1, Device Bus Operations

Corrected symbols for AVD# during the Load Starting Burst Address and Termi-

nate Current Burst Read Cycle and Start New Burst Read Cycle operations to

active rising edge.

Write Buffer Programming Operation

Changed “Sector Address” to “starting address” in the first paragraph.

Read Configuration Register Command

Burst Active Clock Edge Configuration: Deleted reference to active falling edge

settings.

Table 27, Configuration Register

Changed 01b setting definition for CR6 to reserved for future use.

106 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

Tables 30-31, Command Definitions Tables

Added Notes 10 and 11 to Table 31. Corrected definition for SecSi Sector Program

command sequence.

DC Characteristics Table

Added Note 9 to Test Conditions column heading. Added Note 7 reference to ICC4,

ICC5, and ICC6 specifications. Changed maximum specifications for ICC3 at VCC,

ICC4, and ICC6. Added Notes 7 and 8.

VCC Power-up Table and Figure 12, VCC Power-up Diagram

Deleted tVIOS from table and diagram. Moved beginning of tVCS period from VCC

low to VCC high.

Figure 13, CLK Characterization

Deleted CLK Divider waveform from figure.

Synchronous Burst Read Operations table

Deleted tRCC from table. Changed Note 1 to indicate only rising edge of CLK.

Synchronous Burst Mode Read figure.

Deleted figure.

Erase/Program Operations table

Changed specifications for tAH at 54 and 80 MHz speed options.

Changed specification for tWHWH1. Modified Note 3 to indicate rising edge of CLK

only.

Erase and Programming Performance Table

Changed cycles in Note 1 and VCC voltage in Note 2. Added Note 7. Changed typ-

ical and maximum values for Effective Word Programming Time utilizing Program

Write Buffer (at ACC), Total 32-Word Buffer Programming Time (at ACC), Chip

Programming Time (at ACC and VCC).

Physical Dimensions

Deleted 80-ball, 8 x 10 mm package drawing.

Revision C (June 14, 2004)

Global

Changed all 1.65 V VCC and VIO specifications to 1.70 V. Deleted references to 1.8

V VIO.

Distinctive Characteristics

Read access times: Changed specifications for synchronous initial latency and

asynchronous random access times for 80 MHz speed option.

Program and Erase Performance: Changed typical sector erase time for 64 Kword

sectors.

Power dissipation: Changed all specifications listed to new values.

Deleted Hardware Reset input and CMOS compatible input bullets.

ACC input: Added “erase” to bullet text.

General Description

Changed initial latency specification for 80 MHz speed option.

Product Selector Guide

Changed specifications for 80 MHz speed option.

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 107

Preliminary

Block Diagram

Deleted VSSIO input.

Connection Diagrams

MCP Look-Ahead Connection Diagram: Added section.

Input/Output Descriptions

Deleted VIO and VSSIO. Corrected CE#f1 name. Deleted voltage range for VCC.

Added description for RFU.

Ordering Information

Changed reel size for packing types 2, 3. Corrected model numbers for 64 Mb de-

vice. Added Note 3 to all ordering information charts. Deleted BAI and added BFW

to package & temperature valid combinations. Modified DYB power-up state

description.

Configuration Register

Deleted “active clock edge” from paragraph.

Password Sector Protection

Replaced OTP reference in last paragraph with “non-erasable”.

SecSi Sector Protection Bit

Deleted section.

Common Flash Memory Interface (CFI)

Added table reference to second paragraph. Deleted third paragraph.

Table 17, CFI Query Identification String: Changed data for addresses 1Fh, 21h,

and 25h.

Table 18, System Interface String: Changed data for addresses 2Ah.

Table 19, Device Geometry Definition: Changed data and description for ad-

dresses 45h.

Table 22, WS128N Sector & Memory Address Map: Corrected address range and

sector address bit range for SA66.

Set Configuration Register Command Sequence

Deleted reference to active clock edge.

Table 24, Programmable Wait State Settings

Added 80 MHz column.

Table 26, Burst Length Configuration

Changed function and settings descriptions for CR9, CR7, CR6. Added CR5, CR4

to table.

Table 27, Configuration Register

Changed read data for DA15-DQ0 and DQ2 indicator bits (BA) + 03h. Added row

for Sector Block Lock/Unlock codes.

Figure 3, Write Buffer Programming Operation

Deleted WS=31 from second box in figure.

Erase Suspend/Erase Resume Commands

Added tSEA to first paragraph. Added tESL to second paragraph.

Program Suspend/Program Resume Commands

Added tPSL to first paragraph.

108 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

Non-Volatile Sector Protection Command Set Definitions

Added Figure 5 to section.

Table 30, Memory Array Commands

Added Note 18 to table. Deleted sector erase and erase rows from Unlock Bypass

section of table. Added note reference to Set Configuration Register command.

Write Operation Status

Added tPSP to second paragraph and tASP to fourth paragraph.

DQ6: Toggle Bit I

Added tASP to third paragraph. Added tPAP to fifth paragraph.

DQ3: Sector Erase Start Timeout State Indicator

Added tSEA to first paragraph.

Operating Ranges

Changed VCC and VIO supply voltage range specifications.

DC Characteristics

Changed Note 7. Changed specifications for ICCB, ICC1, ICC2, ICC3, ICC4, ICC6. Re-

moved “less than” symbol from ICC5 and IACC.

Synchronous/Burst Read

Changed specifications for tIACC, tOE, tCEZ, tOEZ, tCES, tAVC, tAVD. Deleted tCKA,

tCKZ, tOES. Changed Note 2.

Figure 14, CLK Synchronous Burst Mode Read and Figure 15, 8-word Linear Burst with

Wrap Around

Modified Addresses waveform. Changed Note 4.

Hardware Reset (RESET#) table

Changed specifications for tRP and tRH.

Asynchronous Mode Read table

Changed specifications for tCE, tACC, tAVDP

, tAAVDS, tOE, tOEH, tOEZ. Added note.

Erase/Program Timing table

Changed specifications for tWC, tAS, tAH, tAVDP

, tWP

, tCS, tASW

, tAVHW

, tAVSC, tAVHC.

Added tWEP

, tSEA, tESL, tPSL, tASP

, tPSP

. Deleted tWHWH1 and tWHWH2.

Figure 23, Accelerated Unlock Bypass Programming Timing

Deleted tVIDS value from OE# waveform.

Erase and Programming Performance

Deleted Erase Suspend/Erase Resume Latency, and Program Suspend/Program

Resume Latency specifications from table. Changed specifications for all except

Chip Programming Time. Removed “less than” symbol for Chip Programming

Times. Added Single Word Programming Time specifications. Added Note 8.

Revision D (June 23, 2004)

Distinctive Characteristics

Program and Erase Performance: Changed typical sector erase time for 64 Kword

sectors.

Lock Register

Added lock register table for WS128N and WS064N devices.

Common Flash Memory Interface

Changed data at address 24h.

August 17, 2004 S29WSxxxN_00_E1 S29WSxxxN MirrorBit™ Flash Family 109

Preliminary

Autoselect Addresses table

Added note to (Note is relevant to Indicator Bits).

Write Buffer Programming Command Sequence table

Modified comment for Specify the Number of Program Locations sequence.

Synchronous Burst Read table

Added tCOE parameter to table.

CLK Synchronous Burst Mode Read figure, 8-word Linear Burst with Wrap Around

figure

Added tCOE parameter to figures.

8-word Linear Burst without Wrap Around figure

Added tCOE parameter to figure. In Note 4, changed “4th” to “1st”.

Linear Burst with RDY Set One Cycle Before Data figure

Added tCOE parameter to figure. Lengthened first signal in Data waveform to 1

cycle.

Erase and Programming Performance table

Changed typical chip erase specifications to include tenths of a second.

Revision E (July 16, 2004)

Synchronous/Burst Read, Figure 14. CLK Syncronous Burst Mode Read, and Figure 15.

8-word Linear Burst with Wrap Around.

Added tAOE standard parameter.

Revision E+1 (August 17, 2004)

Accelerated Program/Chip Erase Operations

Reworded section.

Synchronous/Burst Read

Changed tAOE to 38.4 ns.

Table 18, “System Interface String”

Updated table.

Table 27, “Configuration Register”

Added Note.

Figure 6, “Polling Flow Chart’

Added Flow Chart.

Figure 7. Dat# Polling Algorithm and Figure 8. Toggle Bit Algorithm

Removed Flow Charts.

Figure 25, “Synchronous Data Polling Timings/ Toggle Bit Timings’, Figure 27,

“Latency with Boundary Crossing when Frequency > 66 MHz’ and Figure 28, “Latency

with Boundary Crossing into Program/Erase Bank’

Updated notes.

BGA Ball Capacitance

Updated capacitance values.

Corrected CFI table 23h reads 0004h.

110 S29WSxxxN MirrorBit™ Flash Family S29WSxxxN_00_E1 August 17, 2004

Preliminary

Colophon

The products described in this document are designed, developed and manufactured as contemplated for general use, including without limitation, ordinary

industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured as contemplated (1) for any use that

includes fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal

injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass transport control,

medical life support system, missile launch control in weapon system), or (2) for any use where chance of failure is intolerable (i.e., submersible repeater and

artificial satellite). Please note that Spansion will not be liable to you and/or any third party for any claims or damages arising in connection with above-men-

tioned uses of the products. Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures

by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other

abnormal operating conditions. If any products described in this document represent goods or technologies subject to certain restrictions on export under

the Foreign Exchange and Foreign Trade Law of Japan, the US Export Administration Regulations or the applicable laws of any other country, the prior au-

thorization by the respective government entity will be required for export of those products.

Trademarks and Notice

The contents of this document are subject to change without notice.This document may contain information on a SpansionTM product under development by

Spansion LLC. Spansion LLC reserves the right to change or discontinue work on any product without notice. The information in this document is provided

as is without warranty or guarantee of any kind as to its accuracy, completeness, operability, fitness for particular purpose, merchantability, non-infringement

of third-party rights, or any other warranty, express, implied, or statutory. Spansion LLC assumes no liability for any damages of any kind arising out of the

use of the information in this document.

SpansionTM, the SpansionTM logo, MirrorBit, combinations thereof, and ExpressFlash are trademarks of Spansion LLC. Other company and product names used

in this publication are for identification purposes only and may be trademarks of their respective companies.