POWER
DP40
40 Watts
Total Power: 40 Watts
Input Voltage: 90 - 264 Vac
127 - 300 Vdc
# of Outputs: Single
Special FeatureS
Medical and ITE safeties
Universal AC input
Fully regulated output
Overload and short circuit protection
Constant voltage
High efciency
High MTBF
IEC320 AC input receptacle
3 pin (type C14) Class I
2 pin (type C8) Class II
Built in EMI lter (CISPR 22 Class B)
LED power good indicator
Input power <49 watts
Complies with EN61000-3-2
Meets Energy Star Efciency Level V
CE Mark EMC, LVD & ErP 2011
Less than 300 mW No-Load power
consumption
SaFety
UL 60950-1, 60601-1
cUL 60950-1, 60601-1
TUV 60950-1, 60601-1
CE EMC, LVD & ErP 2011
CB Certicate and report
CCC China Approval
Electrical Specications
Input
Input range 90 - 264 Vac (wide range)
127 - 300 Vdc
Frequency 47 - 63 Hz
Inrush current < 50 A @ 230 Vac, cold start @ 25 °C
Input current < 0.5 A rms @ 115 Vac; < 0.25 A @ 230 Vac
Efficiency 84% @ full load typical, @115 Vac
EMI/RFI FCC Part 15, Subpart B Class B & EN55022 (CISPR 22) Class B
Safety ground leakage current 300 μA @ 50/60 Hz, 264 Vac input for 3 pin model
100 μA @ 50/60 Hz, 264 Vac input for 2 pin model
Output
Maximum power (Po) 40 W
Hold-up time 10 ms. typical at full load @ 115 Vac
Overvoltage protection 20% - 45% above nominal output maximum
Latching type, recycle AC to reset.
Overload protection Output short circuit protection auto recover
Overload protected @ 110 - 160% above peak rating
Cable/connector
1.2 m DC cable with 2.5 mm I.D, 5.5 mm O.D center plug
DC plug center +v
DC plug outer -v
Environmental Specications
Operating temperature 0 ° to +40 °C ambient. Derate each output as 2.5% per degree
from 40 °C to 60 °C. -20 °C start up
Storage temperature -40 °C to +85 °C
Electromagnetic susceptibility Designed to meet EN61000-4, -2, -3, -4, -5, -6, -8, -11, Level 3
Humidity Operating; non-condensing 10% to 90% RH
Vibration
Three orthogonal axes, 3 sweeps per axe at 1 oct/min. 2G peak 8 Hz
to 500 Hz, operational
MTBF demonstrated > 550,000 hours at full load and 25 °C ambient conditions
Data Sheet
DP40 Data Sheet
WORLDWIDE OFFICES
Americas
2900 South Diablo Way
Suite B100
Tempe, AZ 85282, USA
+1 888 412 7832
Europe (UK)
Ground Floor Offices, Barberry House
4 Harbour Buildings, Waterfront West
Brierley Hill, West Midlands
DY5 1LN, UK
+44 (0) 1384 842 211
Asia (HK)
14/F, Lu Plaza
2 Wing Yip Street
Kwun Tong, Kowloon
Hong Kong
+852 2176 3333
For more information: www.artesyn.com
For support: productsupport.ep@artesyn.com
Artesyn Embedded Technologies, Artesyn Embedded Power, Artesyn, and all Artesyn related logos are
trademarks and service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are
trade names, trademarks, or registered trademarks of their respective owners. Specifications are subject to
change without notice. © 2019 Artesyn Embedded Technologies, Inc. All rights reserved. For full legal terms and
conditions, please visit www.artesyn.com/legal.
www.artesyn.com
DP40-DS 05Dec2019
Ordering Information
Model
Number Output Voltage Maximum Load Peak Load1Regulation2Ripple
P/P (PARD)3
DP4009N2M 9 V 4.44 A 5.4 A ± 8% 90 mV
DP4009N3M 9 V 4.44 A 5.4 A ± 8% 90 mV
DP4012N2M 12 V 3.33 A 4.4 A ± 5% 120 mV
DP4012N3M 12 V 3.33 A 4.4 A ± 5% 120 mV
DP4015N2M 15 V 2.67 A 3.5 A ± 5% 150 mV
DP4015N3M 15 V 2.67 A 3.5 A ± 5% 150 mV
DP4018N2M 18 V 2.22 A 3.0 A ± 5% 150 mV
DP4018N3M 18 V 2.22 A 3.0 A ± 5% 150 mV
DP4024N2M 24 V 1.67 A 2.2 A ± 5% 240 mV
DP4024N3M 24 V 1.67 A 2.2 A ± 5% 240 mV
DP4048N2M 48 V 0.84 A 1.2 A ± 5% 480 mV
DP4048N3M 48 V 0.84 A 1.2 A ± 5% 480 mV
1. Peak current lasting < 15 seconds with a maximum 10% duty cycle.
2. At 25 ºC including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings.
3. Peak-to-peak with 20 MHz bandwidth and 10 μF (tantalum capacitor) in parallel with a 0.1 μF capacitor at rated line voltage and load ranges.
Notes:
1. Specifications subject to change without notice.
2. All dimensions in inches (mm), tolerance is ± 0.02” (± 0.5 mm)
3. Warranty: 2 year
4. Weight: 0.55 lb./.25 kg
5. AC input power cord sold separately.
6. Specifications are for convection rating at factory settings at 115 Vac input, 25 °C
unless otherwise stated
Mechanical Drawing
48"
(1219 ± 20)
4.88"
(124.0)
2.4"
(61.0)
1.55"
(39.5)
48"
(1219 ± 20)
4.88"
(124.0)
2.4"
(61.0)
1.55"
(39.5)