TC1303C-1I0EMFTR - Microchip Technology

Analog and Interface Product Selector Guide



Thermal Management



Motor Drivers



Interface Peripherals



Power Management



Linear & Mixed-Signal



Safety & Security

www.microchip.com/analog

Analog and Interface Product Solutions

Fall 2011

Table of Contents

2 Analog and Interface Product Selector Guide

Thermal Management

Temperature Sensors ............................................ 4

Logic Output Temperature Sensors .................... 4

Voltage Output Temperature Sensors ................. 4

Serial Output Temperature Sensors ................... 4

Brushless DC Fan Controllers and

Fan Fault Detectors ............................................... 5

Motor Drivers

Stepper Motors, DC Motors and 3 Phase

BLDC Fan Controllers ............................................ 5

Power Management

Voltage References ............................................... 6

Linear Regulators

50-250 mA LDO Linear Regulators .................... 6

300 mA LDO Linear Regulators ......................... 7

500-800 mA LDO Linear Regulators .................. 7

1A and > LDO Linear Regulators ....................... 8

Application Specific LDO Linear Regulators ........ 8

LDO Regulator Combination Products ..................... 8

Switching Regulators ............................................. 9

Switching Regulator Combination Products .............. 9

PWM Controllers ................................................... 9

Charge Pump DC-to-DC Converters ....................... 10

Inverting or Doubling Charge Pumps ................ 10

Inverting and Doubling Charge Pumps ............. 10

Regulated Charge Pumps ................................ 10

CPU/System Supervisors .................................... 10

Voltage Detectors ................................................ 11

Power MOSFET Drivers ........................................ 12

Low-Side Drivers, 0.5A to 1.2A Peak

Output Current ............................................... 12

Low-Side Drivers, 1.5A Peak Output Current ..... 12

Low-Side Drivers, 2.0A to 12.0A Peak

Output Current ............................................... 13

High-Side/Low-Side Drivers ............................. 13

Synchronous Buck High-Side Drivers ................ 13

Battery Chargers ................................................. 14

Hot Swap Controllers ........................................... 14

Linear

Op Amps ............................................................ 15

High Precision Operational Amplifiers ................... 18

Chopper Stabilized ......................................... 18

Auto-Zero ....................................................... 18

Programmable Gain Amplifiers (PGA) .................... 18

Selectable Gain Amplifiers (SGA) .......................... 18

Comparators ....................................................... 19

Mixed Signal

Successive Approximation Register (SAR)

A/D Converters ................................................... 19

Delta-Sigma A/D Converters ................................ 20

Energy Measurement ICs ..................................... 20

Dual-Slope A/D Converters .................................. 20

Binary and BCD A/D Converters ........................... 21

Display A/D Converters ....................................... 21

Digital Potentiometers ......................................... 21

Frequency-to-Voltage/Voltage-to-Frequency

Conver ters .......................................................... 23

D/A Converters ................................................... 23

Interface

Controller Area Network (CAN) Products ................ 24

Infrared Products................................................. 24

Ethernet Products ............................................... 24

Passive Access Products ..................................... 24

LIN Transceiver Products ...................................... 25

Serial Peripherals ................................................ 25

IEEE 802.15.4 ZigBee® RF Transceiver Products ... 25

Stand-alone RF Receiver Products ........................ 25

USB Products ..................................................... 25

Safety & Security

Photoelectric Smoke Detector ICs ........................ 26

Ionization Smoke Detector ICs ............................. 26

Ionization Smoke Detector Front Ends .................. 26

Piezoelectric Horn Drivers .................................... 26

Analog Design and Development Tools

Thermal Management .......................................... 27

Mixed Signal ....................................................... 27

Power Management ............................................. 28

Interface ............................................................. 29

Linear ................................................................. 30

Analog Blank Evaluation Boards ........................... 30

Miscellaneous Analog Demonstration

and Evaluation Tools ........................................... 30

Featured Analog Development Tools

Thermal Management .......................................... 31

Mixed Signal ....................................................... 31

Power Management ............................................. 31

Interface ............................................................. 32

Linear ................................................................. 32

Part Number Designations

Analog Products with “TC” Prefix .......................... 33

Analog Products with “MCP” Prefix ....................... 34

Analog Products with “RE46C” Prefix .................... 35

Need Additional Support and Resources?

Microchip is committed to supporting its customers by

helping design engineers develop products faster and more

efficiently. Customers can access three main service areas at

www.microchip.com. The Support area provides a fast way to

get questions answered. The Sample area offers evaluation

samples of any Microchip device. microchipDIRECT provides

24-hour pricing, ordering, inventory and credit for convenient

purchasing of all Microchip devices and development tools.

This site also features online programming capabilities.

Finally, the Training area offers opportunities to expand your

knowledge with Microchip’s online web seminars and hands-

on courses at our worldwide Technical Training Centers.

Our seminars and training classes are designed to fit your

schedule and offer an overview of many product, development

tool and application topics. Visit www.microchip.com/training

for class content and schedules.

Have you ever encountered a technical dilemma at a critical

point in your design development and your supplier was not

available to answer your questions? Microchip’s first ever

24/7 global technical support line brings technical support

resources any time help is needed. Because some technical

problems require hands-on assistance in order to be resolved

quickly, Microchip has also developed a global team of field

applications engineers and field sales engineers for local

assistance.

Microchip’s integrated analog technology,

peripherals and features are engineered

to meet today’s demanding design

requirements. Our broad spectrum of

analog products addresses thermal

management, power management,

battery management, mixed-signal, linear,

interface and safety & security solutions.

Combined with “Intelligent Analog”

microcontrollers, Microchip offers an

extensive analog portfolio for thousands

of high-performance design applications

in the automotive, communications

(wireless), consumer, computing and

industrial control markets.

Our broad portfolio of stand-alone

analog and interface devices offers

highly integrated solutions that combine

various analog functions in space-saving

packages and support a variety of

bus interfaces. Many of these devices

support functionality that enhances the

analog features currently available on PIC®microcontrollers.

Want a Business Partner,

Not Just a Vendor?

Successful companies recognize the value of a strategic

supplier relationship to help them deliver innovative products

to their markets in a timely manner. They trust their suppliers

to furnish quality components for current design opportunities

as well as provide technology road maps and innovative

solutions to stay ahead of tomorrow’s design trends.

Microchip Technology provides low-risk product development,

lower total system cost and faster time to market to more

than 45,000 of these successful companies worldwide.

Headquartered in Chandler, Arizona, Microchip offers

outstanding technical support along with dependable delivery

and quality.

Founded in 1989, Microchip’s business model is based on

a series of guiding values that aim to establish successful

customer partnerships by exceeding expectations for

products, services and attitude. Continuous improvement,

technology innovation and the pursuit of the highest quality

possible drive Microchip’s company culture.

The result is a worldwide organization dedicated to delivering

whole product solutions which include high performance

silicon devices, easy-to-use development tools, outstanding

technical support and sophisticated technical documentation.

Are Quality and Delivery a Concern?

Microchip’s quality systems are certified according to

the International Organization for Standards/Technical

Specification (ISO/TS)-16949:2002 requirements. This

demonstrates that the Company’s quality systems meet

the most stringent industry quality-management system

standards, resulting in high-quality semiconductor products.

Direct control over manufacturing resources allows shortened

design and production cycles. By owning the wafer fabrication

facilities and the majority of the test and assembly

operations, and by employing proprietary statistical process

control techniques, Microchip has been able to achieve and

maintain high production yields.

Are you Looking for Complete

Analog & Interface Design Solutions?

Microchip Technology’s Stand-Alone Analog & Interface Portfolio

Power

Management

LDO & Switching

Regulators

Charge Pump

DC/DC Converters

Power MOSFET

Drivers

PWM Controllers

System Supervisors

Voltage Detectors

Voltage References

Li-Ion/Li-Polymer

Battery Chargers

Mixed-Signal

A/D Converter

Families

Digital

Potentiometers

D/A Converters

V/F and F/V

Converters

Energy

Measurement

ICs

Interface

CAN Peripherals

Infrared

Peripherals

LIN Transceivers

Serial Peripherals

Ethernet Controllers

USB Peripheral

Linear

Op Amps

Programmable

Gain

Ampliﬁers

Comparators

Safety & Security

Photoelectric

Smoke Detectors

Ionization Smoke

Detectors

Ionization Smoke

Detector Front Ends

Piezoelectric

Horn Drivers

Thermal

Management

Temperature

Sensors

Fan Speed

Controllers/

Fan Fault

Detectors

Motor Drive

Stepper and DC

3Ф Brushless

DC Fan Controller

Analog and Interface Product Selector Guide 3

Analog and Interface Product Selector Guide 4

THERMAL MANAGEMENT

THERMAL MANAGEMENT PRODUCTS – Temperature Sensors

Part # Typical

Accuracy

(°C)

Maximum

Accuracy

@ 25°C (°C)

Maximum

Temperature

Range (°C) Vcc Range

(V) Maximum

Supply

Current (μA) Features Packages

Logic Output Temperature Sensors

TC6501 ±0.5 ±3 -55 to +125 +2.7 to +5.5 40 Cross to MAX6501, Open-drain 5-pin SOT-23A

TC6502 ±0.5 ±3 -55 to +125 +2.7 to +5.5 40 Cross to MAX6502, Push-pull 5-pin SOT-23A

TC6503 ±0.5 ±3 -55 to +125 +2.7 to +5.5 40 Cross to MAX6503, Open-drain 5-pin SOT-23A

TC6504 ±0.5 ±3 -55 to +125 +2.7 to +5.5 40 Cross to MAX6504, Push-pull 5-pin SOT-23A

TC620 ±1 ±3 -40 to +125 +4.5 to +18 400 Two resistor-programmable trip points 8-pin PDIP, 8-pin SOIC

TC621 Note 1 Note 1 -40 to +85 +4.5 to +18 400 Requires external thermistor, resistor-programmable trip points 8-pin PDIP, 8-pin SOIC

TC622 ±1 ±5 -40 to +125 +4.5 to +18 600 Dual output, TO-220 for heat sink mounting, resistor-programmable trip points 8-pin PDIP, 8-pin SOIC, 5-pin TO-220

TC623 ±1 ±3 -40 to +125 +2.7 to +4.5 250 Two resistor-programmable trip points 8-pin PDIP, 8-pin SOIC

TC624 ±1 ±5 -40 to +125 +2.7 to +4.5 300 Dual output, resistor-programmable trip points 8-pin PDIP, 8-pin SOIC

MCP9501 ±1 ±4 -40 to +125 +2.7 to +5.5 40 Active-High, Push-Pull Output, Rising Temperature Switch 5-pin SOT-23

MCP9502 ±1 ±4 -40 to +125 +2.7 to +5.5 40 Active-Low, Open Drain Output, Rising Temperature Switch 5-pin SOT-23

MCP9503 ±1 ±4 -40 to +125 +2.7 to +5.5 40 Active-High, Push-Pull Output, Falling Temperature Switch 5-pin SOT-23

MCP9504 ±1 ±4 -40 to +125 +2.7 to +5.5 40 Active-Low, Open Drain Output, Falling Temperature Switch 5-pin SOT-23

MCP9509 ±0.5 NS -40 to +125 +2.7 to +5.5 50 Resistor-programmable temperature switch 5-pin SOT-23

MCP9510 ±0.5 NS -40 to +125 +2.7 to +5.5 80 Resistor-programmable temperature switch 6-pin SOT-23

Voltage Output Temperature Sensors

MCP9700 ±1 ±4 -40 to +125 +2.3 to +5.5 12 Linear Active Thermistor® IC, Temperature slope: 10 mV/°C 3-pin TO-92, 5-pin SC-70, 3-pin SOT-23

MCP9701 ±1 ±4 -10 to +125 +3.1 to +5.5 12 Linear Active Thermistor® IC, Temperature slope: 19.53 mV/°C, cross to MAX6612 3-pin TO-92, 5-pin SC-70, 3-pin SOT-23

MCP9700A ±1 ±2 -40 to +125 +2.3 to +5.5 12 Linear Active Thermistor® IC, Temperature slope: 10 mV/°C 3-pin TO-92, 5-pin SC-70, 3-pin SOT-23

MCP9701A ±1 ±2 -40 to +125 +3.1 to +5.5 12 Linear Active Thermistor® IC, Temperature slope: 19.53 mV/°C, cross to MAX6612 3-pin TO-92, 5-pin SC-70, 3-pin SOT-23

TC1046 ±0.5 ±2 -40 to +125 +2.7 to +4.4 60 High precision temperature-to-voltage converter, 6.25 mV/°C 3-pin SOT-23B

TC1047 ±0.5 ±2 -40 to +125 +2.7 to +4.4 60 High precision temperature-to-voltage converter, 10 mV/°C 3-pin SOT-23B

TC1047A ±0.5 ±2 -40 to +125 +2.5 to +5.5 60 High precision temperature-to-voltage converter, 10 mV/°C 3-pin SOT-23B

Serial Output Temperature Sensors

MCP9800 ±0.5 ±1 -55 to +125 +2.7 to +5.5 400 SMbus/I2C™ compatible interface, 0.0625°C to 0.5°C adj. resolution, Power-saving one-shot

temperature measurement 5-pin SOT-23

MCP9801 ±0.5 ±1 -55 to +125 +2.7 to +5.5 400 SMbus/I2C™ compatible interface, 0.0625°C to 0.5°C adj. resolution, Power-saving one-shot

temperature measurement, multi-drop capability 8-pin MSOP, 8-pin SOIC

MCP9802 ±0.5 ±1 -55 to +125 +2.7 to +5.5 400 SMbus/I2C™ compatible interface with time out, 0.0625°C to 0.5°C adj. resolution, Power-saving

one-shot temperature measurement 5-pin SOT-23

MCP9803 ±0.5 ±1 -55 to +125 +2.7 to +5.5 400 SMbus/I2C™ compatible interface with time out, 0.0625°C to 0.5°C adj. resolution, Power-saving

one-shot temperature measurement, Multi-drop capability 8-pin MSOP, 8-pin SOIC

MCP9804 ±0.25 ±1 -40 to +125 +2.7 to +5.5 400 User programmable temperature limits with alert output, 1°C temp. accuracy from -40°C to +125°C 8-pin MSOP, 8-pin 2x3 DFN

MCP9805 ±0.5 ±1(2) -20 to +125 +3.0 to +3.6 400 JEDEC compatible register set, SMbus/I2C™ compatible interface, Programmable, Shut-down modes

and EVENT output 8-pin TSSOP, 8-pin 2x3 DFN

MCP9843 ±0.5 ±1(2) -20 to +125 +3.0 to +3.6 500 Compliant to JEDEC TS2002 speciﬁ cation 8-pin TSSOP, 8-pin 2x3 DFN, 8-pin 2x3 TDFN

MCP98242 ±0.5 ±1(2) -20 to +125 +3.0 to +3.6 400 Same temperature sensor as MCP9805 plus integrated DDR2 Serial Presence Detect EEPROM 8-pin TSSOP, 8-pin 2x3 DFN

MCP98243 ±1 ±3 -40 to +125 +3.0 to +3.6 500 Serial output temperature sensor with integrated EEPROM 8-pin TSSOP, 8-pin 2x3 DFN, 8-pin 2x3 TDFN

TC77 ±0.5 ±1 -55 to +125 +2.7 to +5.5 400 SPI compatible interface, 0.0625°C temperature resolution 5-pin SOT-23A, 8-pin SOIC

TC72 ±0.5 ±1 -55 to +125 +2.65 to +5.5 400 SPI compatible interface, Power-saving one-shot temperature measurement, 0.25°C temperature

resolution 8-pin MSOP, 8-pin 3x3 DFN

TC74 ±0.5 ±2 -40 to +125 +2.7 to +5.5 350 SMbus/I2C™ compatible interface, 1°C temperature resolution 5-pin SOT-23A, 5-pin TO-220

Note 1: These devices use an external temperature sensor. Accuracy of the total solution is a function of the accuracy of the external sensor.

2: Maximum accuracy measured at 85°C.

Analog and Interface Product Selector Guide 5

THERMAL MANAGEMENT PRODUCTS – Brushless DC Fan Controllers and Fan Fault Detectors

Part # Description Typical

Accuracy

(°C)

Maximum

Accuracy

@ 25°C (°C)

Maximum

Temperature

Range (°C) Vcc Range

(V) Maximum

Supply

Current (μA) Features Packages

TC642 Fan Manager Note 1 Note 1 -40 to +85 +3.0 to +5.5 1,000 FanSense™ Fan Monitor, Minimum fan speed control 8-pin PDIP, 8-pin SOIC, 8-pin MSOP

TC642B Fan Manager Note 1 Note 1 -40 to +85 +3.0 to +5.5 400 FanSense™ Fan Monitor, Minimum fan speed control, Fan auto-restart 8-pin PDIP, 8-pin SOIC, 8-pin MSOP

TC646 Fan Manager Note 1 Note 1 -40 to +85 +3.0 to +5.5 1,000 FanSense™ Fan Monitor, Auto-shutdown 8-pin PDIP, 8-pin SOIC, 8-pin MSOP

TC646B Fan Manager Note 1 Note 1 -40 to +85 +3.0 to +5.5 400 FanSense™ Fan Monitor, Auto-shutdown, Fan auto-restart 8-pin PDIP, 8-pin SOIC, 8-pin MSOP

TC647 Fan Manager Note 1 Note 1 -40 to +85 +3.0 to +5.5 1,000 FanSense™ Fan Monitor, Minimum fan speed control 8-pin PDIP, 8-pin SOIC, 8-pin MSOP

TC647B Fan Manager Note 1 Note 1 -40 to +85 +3.0 to +5.5 400 FanSense™ Fan Monitor, Minimum fan speed control, Fan auto-restart 8-pin PDIP, 8-pin SOIC, 8-pin MSOP

TC648 Fan Manager Note 1 Note 1 -40 to +85 +3.0 to +5.5 1,000 Overtemperature alert, Auto-shutdown 8-pin PDIP, 8-pin SOIC, 8-pin MSOP

TC648B Fan Manager Note 1 Note 1 -40 to +85 +3.0 to +5.5 400 Overtemperature alert, Auto-shutdown, Fan auto-restart 8-pin PDIP, 8-pin SOIC, 8-pin MSOP

TC649 Fan Manager Note 1 Note 1 -40 to +85 +3.0 to +5.5 1,000 FanSense™ Fan Monitor, Auto-shutdown 8-pin PDIP, 8-pin SOIC, 8-pin MSOP

TC649B Fan Manager Note 1 Note 1 -40 to +85 +3.0 to +5.5 400 FanSense™ Fan Monitor, Auto-shutdown, Fan auto-restart 8-pin PDIP, 8-pin SOIC, 8-pin MSOP

TC650 Fan Manager ±1 ±3 -40 to +125 +2.8 to +5.5 90 Overtemperature alert 8-pin MSOP

TC651 Fan Manager ±1 ±3 -40 to +125 +2.8 to +5.5 90 Overtemperature alert, Auto-shutdown 8-pin MSOP

TC652 Fan Manager ±1 ±3 -40 to +125 +2.8 to +5.5 90 FanSense™ Fan Monitor, Overtemperature alert 8-pin MSOP

TC653 Fan Manager ±1 ±3 -40 to +125 +2.8 to +5.5 90 FanSense™ Fan Monitor, Overtemperature alert, Auto-shutdown 8-pin MSOP

TC654 Dual SMbus Fan Manager Note 1 Note 1 -40 to +85 +3.0 to +5.5 320 FanSense™ Fan Monitor, RPM data 10-pin MSOP

TC655 Dual SMbus Fan Manager Note 1 Note 1 -40 to +85 +3.0 to +5.5 320 FanSense™ Fan Monitor, RPM data, Overtemperature alert 10-pin MSOP

TC664 Single SMbus Fan Manager Note 1 Note 1 -40 to +85 +3.0 to +5.5 320 FanSense™ Fan Monitor, RPM data 10-pin MSOP

TC665 Single SMbus Fan Manager Note 1 Note 1 -40 to +85 +3.0 to +5.5 320 FanSense™ Fan Monitor, RPM data, Overtemperature alert 10-pin MSOP

TC670 Predictive Fan Fault Detector N/A N/A -40 to +85 +3.0 to +5.5 150 FanSense™ Fan Monitor, Programmable threshold 6-pin SOT-23

Note 1: These devices use an external temperature sensor. Accuracy of the total solution is a function of the accuracy of the external sensor.

MOTOR DRIVERS

MOTOR DRIVER PRODUCTS - Stepper Motors, DC Motors and 3 Phase BLDC Fan Controllers

Part # Motor

Type Input

Voltage

Range (V)

Internal/

External

FETs

Output

Current

(mA) Control Scheme Motor

Speed

Output Shutdown

Protection Temperature

Operating

Range (°C) Features Packages

MTS62C19A One Bipolar Stepper

Motor or Two DC

Motors 10.0 to 40.0 Internal 750 Direct PWM Input,

Current Limit Control,

Microstepping No Overtemperature,

Under Voltage -20 to +85 Dual Full Bridge Motor Driver for Stepper Motors,

Pin compatible with Allegro 6219 24-pin SOIC

MTS2916A One Bipolar Stepper

Motor or Two DC

Motors 10.0 to 40.0 Internal 750 Direct PWM Input,

Current Limit Control,

Microstepping No Overtemperature,

Under Voltage -20 to +85 Dual Full Bridge Motor Driver for Stepper Motors,

Pin compatible with Allegro 2916 24-pin SOIC

MTD6501C 3 Phase Brushless

Fan 2.0 to 14.0 Internal 800 Sensorless Sinusoidal Frequency

Generator Short Circuit

Overtemperature,

Motor Lock-up -30 to +95 3-Phase BLDC Sinusoidal Sensorless Fan Motor

Driver, Overcurrent limitation Thermally

Enhanced 8-pin

SOP

MTD6501D 3 Phase Brushless

Fan 2.0 to 14.0 Internal 500 Sensorless Sinusoidal Frequency

Generator Short Circuit

Overtemperature,

Motor Lock-up -30 to +95 3-Phase BLDC Sinusoidal Sensorless Fan Motor

Driver, Overcurrent limitation 10-pin MSOP

MTD6502B 3 Phase Brushless

Fan 2.0 to 5.5 Internal 750 Sensorless Sinusoidal Frequency

Generator Short Circuit

Overtemperature,

Motor Lock-up -40 to +85 3-Phase BLDC Sinusoidal Sensorless Fan Motor

Driver, Direction control, Overcurrent limitation 10-pin TDFN 3x3

Serial Output Temperature Sensors

Part # Typical

Accuracy

(°C)

Maximum

Accuracy

@ 25°C (°C)

Maximum

Temperature

Range (°C) Vcc Range

(V) Maximum

Supply

Current (μA) Features Packages

TCN75A ±0.5 ±2 -40 to +125 +2.7 to +5.5 500 SMbus/I2C™ compatible interface, power-saving one-shot temperature measurement, multi-drop capability,

0.0625°C to 0.5°C adjustable temperature resolution 8-pin MSOP, 8-pin SOIC

TCN75 ±0.5 ±2 -55 to +125 +2.7 to +5.5 1,000(3) SMbus/I2C™ compatible interface, multi-drop capability, interrupt output, 0.5°C temperature resolution 8-pin MSOP, 8-pin SOIC

Note 1: These devices use an external temperature sensor. Accuracy of the total solution is a function of the accuracy of the external sensor.

2: Maximum accuracy measured at 85°C.

3: TCN75 idle current is 250 mA. This device also has a Software Shutdown mode that reduces supply current to <1 A.

Analog and Interface Product Selector Guide 6

POWER MANAGEMENT

POWER MANAGEMENT – Voltage References

Part # Vcc Range

(V) Output Voltage (V) Max. Load

Current (mA) Initial Accuracy

(max.%) Temperature

Coefﬁ cient (ppm/°C) Maximum Supply

Current (μA @ 25°C) Packages

MCP1525 2.7 to 5.5 2.5 ±2 ±1 50 100 3-pin TO-92, 3-pin SOT-23B

MCP1541 4.3 to 5.5 4.096 ±2 ±1 50 100 3-pin TO-92, 3-pin SOT-23B

POWER MANAGEMENT – Linear Regulators

Part # Max. Input

Voltage (V) Output Voltage (V) Output

Current

(mA)

Junction

Temperature

Range (°C)

Typical

Active

Current (μA)

Typical Dropout

Voltage @ Max.

Iout (mV)

Typical Output

Voltage

Accuracy (%) Features Packages

50 mA to 250 mA Low-Dropout Linear Regulators

TC2014 6.0 1.8, 2.7, 2.8, 3.0, 3.3 50 -40 to +125 55 45 ±0.4 Ceramic output capacitor stable,

Shutdown, Reference bypass input 5-pin SOT-23A

TC1014 6.0 1.8, 2.5, 2.7, 2.8, 2.85, 3.0, 3.3, 3.6, 4.0, 5.0 50 -40 to +125 50 85 ±0.5 Shutdown, Reference bypass input 5-pin SOT-23A

TC2054 6.0 1.8, 2.7, 2.8, 3.0, 3.3 50 -40 to +125 55 45 ±0.4 Ceramic output capacitor stable,

Shutdown, Error output 5-pin SOT-23A

TC1054 6.0 1.8, 2.5, 2.7, 2.8, 2.85, 3.0, 3.3, 3.6, 4.0, 5.0 50 -40 to +125 50 85 ±0.5 Shutdown, Error output 5-pin SOT-23A

TC1070 6.0 1.23  VIN 50 -40 to +125 50 85 – Shutdown, Adjustable 5-pin SOT-23A

TC1072 6.0 2.5, 2.7, 2.8, 2.85, 3.0, 3.3, 3.6, 4.0, 5.0 50 -40 to +125 50 85 ±0.5 Shutdown, Reference bypass input,

Error output 6-pin SOT-23A

TC1223 6.0 2.5, 2.7, 2.8, 3.0, 3.3, 3.6, 4.0, 5.0 50 -40 to +125 50 85 ±0.5 Shutdown 5-pin SOT-23A

MCP1790 30 3.0, 3.3, 5.0 70 -40 to +125 70 500 ±0.2 Ceramic output capacitor stable 3-pin SOT-223, 3-pin DDPAK

MCP1791 30 3.0, 3.3, 5.0 70 -40 to +125 70 500 ±0.2 Ceramic output capacitor stable,

Shutdown, Power good 5-pin SOT-223, 5-pin DDPAK

TC1016 6.0 1.8, 2.7, 2.8, 3.0 80 -40 to +125 50 150 ±0.5 Ceramic output capacitor stable,

Shutdown 5-pin SC-70, 5-pin SOT-23A

TC2015 6.0 1.8, 2.5, 2.6, 2.7, 2.8, 2.85, 3.0, 3.3, 5.0 100 -40 to +125 55 90 ±0.4 Ceramic output capacitor stable,

Shutdown, Reference bypass input 5-pin SOT-23A

TC1015 6.0 1.8, 2.5, 2.7, 2.8, 2.85, 3.0, 3.3, 3.6, 4.0, 5.0 100 -40 to +125 50 180 ±0.5 Shutdown, Reference bypass input 5-pin SOT-23A

TC2055 6.0 1.8, 2.7, 2.8, 3.0, 3.3 100 -40 to +125 55 90 ±0.4 Ceramic output capacitor stable,

Shutdown, Error output 5-pin SOT-23A

TC1055 6.0 1.8, 2.5, 2.7, 2.8, 2.85, 3.0, 3.3, 3.6, 4.0, 5.0 100 -40 to +125 50 180 ±0.5 Shutdown, Error output 5-pin SOT-23A

TC1071 6.0 1.23  VIN 100 -40 to +125 50 180 – Shutdown, Adjustable 5-pin SOT-23A

TC1073 6.0 2.5, 2.7, 2.8, 2.85, 3.0, 3.3, 3.6, 4.0, 5.0 100 -40 to +125 50 180 ±0.5 Shutdown, Reference bypass input,

Error output 6-pin SOT-23A

TC1224 6.0 2.5, 2.7, 2.8, 3.0, 3.3, 3.6, 4.0, 5.0 100 -40 to +125 50 180 ±0.5 Shutdown 5-pin SOT-23A

TC1188 6.0 1.8, 2.8, 2.84, 3.15 120 -40 to +125 50 130 ±0.5 Shutdown 5-pin SOT-23A

TC1189 6.0 1.8, 2.8, 2.84, 3.15 120 -40 to +125 50 130 ±0.5 Shutdown 5-pin SOT-23A

TC2185 6.0 1.8, 2.7, 2.8, 3.0, 3.3 150 -40 to +125 55 140 ±0.4 Ceramic output capacitor stable,

Shutdown, Reference bypass input 5-pin SOT-23A

TC1185 6.0 1.8, 2.5, 2.7, 2.8, 2.85, 3.0, 3.3, 3.6, 4.0, 5.0 150 -40 to +125 50 270 ±0.5 Shutdown, Reference bypass input 5-pin SOT-23A

TC2186 6.0 1.8, 2.7, 2.8, 3.0, 3.3 150 -40 to +125 55 140 ±0.4 Ceramic output capacitor stable,

Shutdown, Error output 5-pin SOT-23A

TC1186 6.0 1.8, 2.5, 2.7, 2.8, 2.85, 3.0, 3.3, 3.6, 4.0, 5.0 150 -40 to +125 50 270 ±0.5 Shutdown, Error output 5-pin SOT-23A

TC1187 6.0 1.23  VIN 150 -40 to +125 50 270 – Shutdown, Adjustable 5-pin SOT-23A

TC1017 6.0 1.8, 2.6, 2.7, 2.8, 2.85, 2.9, 3.3, 3.4 150 -40 to +125 53 285 ±0.5 Ceramic output capacitor stable,

Shutdown 5-pin SOT-23A, 5-pin SC-70

MCP1754 16 1.8, 2.5, 2.7, 2.8, 2.85, 3.0, 3.3, 3.6, 4.0, 5.0 150 -40 to +125 56 300 ±2 70 dB PSRR 5-pin SOT-23, 5-pin SOT-89,

5-pin SOT-223, 8-pin 2x3 TDFN

MCP1754S 16 1.8, 2.5, 2.7, 2.8, 2.85, 3.0, 3.3, 3.6, 4.0, 5.0 150 -40 to +125 56 300 ±2 70 dB PSRR 3-pin SOT-23, 3-pin SOT-89,

3-pin SOT-223, 8-pin 2x3 TDFN

Analog and Interface Product Selector Guide 7

POWER MANAGEMENT – Linear Regulators (Continued)

Part # Max. Input

Voltage (V) Output Voltage (V) Output

Current

(mA)

Junction

Temperature

Range (°C)

Typical

Active

Current (μA)

Typical Dropout

Voltage @ Max.

Iout (mV)

Typical Output

Voltage

Accuracy (%) Features Packages

50 mA to 250 mA Low-Dropout Linear Regulators (Continued)

MCP1801 10 0.9, 1.2, 1.8, 2.5, 3.0, 3.3, 5.0, 6.0 150 -40 to +85 25 250 ±0.4 Ceramic output capacitor stable,

Shutdown, High PSRR 5-pin SOT-23A

MCP1804 28 1.8 to 18 150 -40 to +85 50 1300 ±2 Shutdown, High PSRR 5-pin SOT-23, 5-pin SOT-89,

3-pin SOT-89, 3-pin SOT-223

MCP1700 6.0 1.2, 1.8, 2.5, 3.0, 3.3, 5.0 250 -40 to +125 1.6 300 ±0.4 1.0 μF ceramic cap stable,

Short-circuit protection 3-pin TO-92, 3-pin SOT-23A,

3-pin SOT-89

MCP1701A 10 1.8, 2.5, 3.0, 3.3, 5.0 250 -40 to +85 1.6 380 ±0.5 10V max. input voltage 3-pin TO-92, 3-pin SOT-23A,

3-pin SOT-89

MCP1702 13.2 1.2, 1.5, 1.8, 2.5, 2.8, 3.0, 3.3, 4.0, 5.0 250 -40 to +125 2 650 ±0.4 Ceramic output capacitor stable,

Ultra-low ground current, 13.2V VIN max. 3-pin TO-92, 3-pin SOT-23A,

3-pin SOT-89

MCP1703 16 1.2, 1.5, 1.8, 2.5, 2.8, 3.0, 3.3, 4.0, 5.0 250 -40 to +125 2 650 ±0.4 Ceramic output capacitor stable,

Ultra-low ground current, 16V VIN max. 3-pin SOT-23A, 3-pin SOT-89,

3-pin SOT-223

300 mA Low-Dropout Linear Regulators

TC1107 6.0 2.5, 2.7, 2.8, 3.0, 3.3, 5.0 300 -40 to +125 50 240 ±0.5 Shutdown, Reference bypass input 8-pin MSOP, 8-pin SOIC

TC1108 6.0 2.5, 2.7, 2.8, 3.0, 3.3, 5.0 300 -40 to +125 50 240 ±0.5 3-pin SOT-223

TC1173 6.0 2.5, 2.7, 2.8, 3.0, 3.3, 5.0 300 -40 to +125 50 240 ±0.5 Shutdown, Reference bypass input, Error

output 8-pin MSOP, 8-pin SOIC

TC1174 6.0 1.23  VIN 300 -40 to +125 50 240 – Shutdown, Reference bypass input,

Adjustable 8-pin MSOP, 8-pin SOIC

TC1269 6.0 2.5, 2.8, 3.0, 3.3, 5.0 300 -40 to +125 50 240 ±0.5 Shutdown, Reference bypass input 8-pin MSOP

MCP1802 10 0.9, 1.2, 1.8, 2.5, 3.0, 3.3, 5.0, 6.0 300 -40 to +85 25 250 ±0.4 Ceramic output capacitor stable,

Shutdown, High PSRR 5-pin SOT-23A

MCP1824 6.0 Fixed: 0.8, 1.2, 1.8, 2.5, 3.0, 3.3, 5.0

Adjustable: 0.8 to 5.0 300 -40 to +125 120 200 ±0.5 Ceramic output capacitor stable,

Shutdown, Power good 5-pin SOT-223, 5-pin SOT-23

MCP1824S 6.0 0.8, 1.2, 1.8, 2.5, 3.0, 3.3, 5.0 300 -40 to +125 120 200 ±0.5 Ceramic output capacitor stable 3-pin SOT-223

500 mA to 800 mA Low-Dropout Linear Regulators

TC1262 6.0 2.5, 2.8, 3.0, 3.3, 5.0 500 -40 to +125 80 350 ±0.5 Overtemperature protection,

Overcurrent protection 3-pin TO-220, 3-pin DDPAK,

3-pin SOT-223

TC1263 6.0 2.5, 2.8, 3.0, 3.3, 5.0 500 -40 to +125 80 350 ±0.5 Shutdown, Reference bypass input,

Error output 8-pin SOIC, 5-pin TO-220,

5-pin DDPAK

TC1268 6.0 2.5 500 -40 to +125 80 350 ±0.5 Shutdown, Reference bypass input,

Error output 8-pin SOIC

MCP1725 6.0 0.8, 1.2, 1.8, 2.5, 3.0, 3.3, 5.0 500 -40 to +125 120 210 ±0.5 Ceramic output capacitor stable,

Shutdown, CDELAY, Power good 8-pin 2x3 DFN, 8-pin SOIC

MCP1825 6.0 Fixed: 0.8,1.2,1.8, 2.5, 3.0, 3.3, 5

Adjustable: 0.8 to 5.0 500 -40 to +125 120 210 ±0.5 Ceramic output capacitor stable, Shutdown,

Power good 5-pin TO-220, 5-pin DDPAK,

5-pin SOT-223

MCP1825S 6.0 0.8,1.2,1.8, 2.5, 3.0, 3.3, 5 500 -40 to +125 120 210 ±0.5 Ceramic output capacitor stable 3-pin TO-220, 3-pin DDPAK,

3-pin SOT-223

TC1264 6.0 1.8, 2.5, 3.0, 3.3 800 -40 to +125 80 450 ±0.5 Overtemperature protection,

Overcurrent protection 3-pin TO-220, 3-pin DDPAK,

3-pin SOT-223

TC1265 6.0 1.8, 2.5, 3.0, 3.3 800 -40 to +125 80 450 ±0.5 Shutdown, Reference bypass input,

Error output 8-pin SOIC, 5-pin TO-220,

5-pin DDPAK

TC2117 6.0 1.8, 2.5, 3.0, 3.3 800 -40 to +125 80 600 ±0.5 Overtemperature protection,

Overcurrent protection 3-pin SOT-223, 3-pin DDPAK

Analog and Interface Product Selector Guide 8

POWER MANAGEMENT – Low-Dropout Regulator Combination Products

TC1300(1) 6.0 2.5, 2.7, 2.8, 2.85, 3.0, 3.3 300 -40 to +125 80 210 ±0.5 Shutdown, Reference bypass input,

LDO plus Reset output 8-pin MSOP

TC1301A(1) 6.0 LDO1: 1.5-3.3

LDO2: 1.5-3.3 LDO1: 300

LDO2: 150 -40 to +125 103 LDO1: 104

LDO2: 150 ±0.5 Dual LDO plus Reset output, Shutdown,

Reference bypass, Voltage detect 8-pin MSOP, 8-pin 3x3 DFN

TC1301B(1) 6.0 LDO1: 1.5-3.3

LDO2: 1.5-3.3 LDO1: 300

LDO2: 150 -40 to +125 114 LDO1: 104

LDO2: 150 ±0.5 Dual LDO plus Reset, per channel output

shutdown, Reference bypass 8-pin MSOP, 8-pin 3x3 DFN

TC1302A(1) 6.0 LDO1: 1.5-3.3

LDO2: 1.5-3.3 LDO1: 300

LDO2: 150 -40 to +125 103 LDO1: 104

LDO2: 150 ±0.5 Dual LDO, Output shutdown reference

bypass, Voltage detect 8-pin MSOP, 8-pin 3x3 DFN

TC1302B(1) 6.0 LDO1: 1.5-3.3

LDO2: 1.5-3.3 LDO1: 300

LDO2: 150 -40 to +125 114 LDO1: 104

LDO2: 150 ±0.5 Dual LDO, per channel output shutdown,

Reference bypass 8-pin MSOP, 8-pin 3x3 DFN

TC1305 6.0 2.5, 2.8, 3.0 150(1) -40 to +125 120 240 ±0.5 Dual LDO plus Reset output, Reference

bypass input, Shutdown, Select Mode™

selectable output voltages 10-pin MSOP

TC1306 6.0 1.8, 2.8, 3.0 150(1) -40 to +125 120 240 ±0.5 Dual LDO plus Reset output, Shutdown,

Select Mode™ selectable output voltages 8-pin MSOP

TC1307(1) 6.0 1.8, 2.5, 2.8, 3.0 150(1) -40 to +125 220 200 ±0.5 Quad LDO plus Reset output, Shutdown,

Select Mode™ selectable output voltage 16-pin QSOP

Note 1: LDOs with shutdown (except Power Management Combination Products as indicated) have typical shutdown currents of 0.05 mA.

POWER MANAGEMENT – Linear Regulators (Continued)

Part # Max. Input

Voltage (V) Output Voltage (V) Output

Current

(mA)

Junction

Temperature

Range (°C)

Typical

Active

Current (μA)

Typical Dropout

Voltage @ Max.

Iout (mV)

Typical Output

Voltage

Accuracy (%) Features Packages

1A and Above Low-Dropout Linear Regulators

MCP1726 6.0 Fixed: 0.8,1.2,1.8, 2.5, 3.0, 3.3, 5

Adjustable: 0.8 to 5.0 1000 -40 to +125 140 300 ±0.4 Ceramic output capacitor stable, Shutdown,

CDELAY, Power good 8-pin 3x3 DFN, 8-pin SOIC

MCP1826 6.0 Fixed: 0.8,1.2,1.8, 2.5, 3.0, 3.3, 5

Adjustable: 0.8 to 5.0 1000 -40 to +125 140 300 ±0.5 Ceramic output capacitor stable, Shutdown,

Power good 5-pin TO-220, 5-pin DDPAK, 5-pin

SOT-223

MCP1826S 6.0 0.8,1.2,1.8, 2.5, 3.0, 3.3, 5 1000 -40 to +125 140 300 ±0.5 Ceramic output capacitor stable 3-pin TO-220, 3-pin DDPAK, 3-pin

SOT-223

MCP1727 6.0 Fixed: 0.8,1.2,1.8, 2.5, 3.0, 3.3, 5

Adjustable: 0.8 to 5.0 1500 -40 to +125 140 330 ±0.5 Ceramic output capacitor stable, Shutdown,

CDELAY, Power good 8-pin 3x3 DFN, 8-pin SOIC

MCP1827 6.0 Fixed: 0.8,1.2,1.8, 2.5, 3.0, 3.3, 5

Adjustable: 0.8 to 5.0 1500 -40 to +125 140 330 ±0.5 Ceramic output capacitor stable, Shutdown,

Power good 5-pin DDPAK, 5-pin TO-220

MCP1827S 6.0 0.8,1.2,1.8, 2.5, 3.0, 3.3, 5 1500 -40 to +125 140 330 ±0.5 Ceramic output capacitor stable 3-pin DDPAK, 3-pin TO-220

Application Speciﬁ c Low-Dropout Linear Regulators

TC1266 6.0 3.3 200 -5 to +70 230 200 ±1.0 PCI compliant 8-pin SOIC, 8-pin MSOP

TC1267 6.0 3.3 400 -5 to +70 230 300 ±1.0 PCI compliant 5-pin DDPAK

TC57 8 2.5, 3.0, 3.3 4,000(1) -40 to +85 50 100(1) ±2.0 Shutdown, External transistor 5-pin SOT-23A

TC59 -10 -3.0, -5.0 100 -40 to +85 3 380 ±0.5 Negative LDO 3-pin SOT-23A

Note 1: Depending on external transistor conﬁ guration.

Analog and Interface Product Selector Guide 9

POWER MANAGEMENT – Switching Regulators

Part # Description Input

Voltage

Range (V) Output

Voltage (V) Operating

Temperature

Range (°C) Control

Scheme Switching

Frequency

(kHz) Typical Active

Current (μA) Output

Current

(mA) Features Packages

MCP1601 Synchronous Buck Regulator 2.7 to 5.5 0.9V to VIN -40 to +85 PFM/PWM/LDO 750 825 (PWM)

125 (PFM) 500 UVLO, Auto-switching, LDO 8-pin MSOP

MCP1602 Synchronous Buck Regulator 2.7 to 5.5 0.8 to 4.5 -40 to +85 PFM/PWM 2000 35 500 PFM, PWM auto-switching, UVLO, Soft start,

Power good indicator 10-pin MSOP,

10-pin 3x3 DFN

MCP1603 Synchronous Buck Regulator 2.7 to 5.5 0.8 to 4.0 -40 to +85 PFM/PWM 2000 45 500 Overtemperature and Overcurrent protection 5-pin TSOT -23,

8-pin 2x3 DFN

MCP1612 Synchronous Buck Regulator 2.7 to VIN 0.8 to 5.5 -40 to +85 Constant frequency,

PWM 1400 10,000 1000 Overall efﬁ ciency >94%, Soft start,

Overtemperature and Overcurrent protection 8-pin MSOP,

8-pin 3x3 DFN

MCP1623/4 Step-up DC/DC Regulator 0.65 to 6 2.0 to 5.5 -40 to +85 PWM or

PWM/PFM 500 19 175 Integrated synchronous boost regulator, 0.65V

start-up voltage, Soft start, True load disconnect 6-pin SOT-23,

8-pin 2x3 DFN

MCP1640/B/

C/D Step-up DC/DC Regulator 0.65 to 6 2.0 to 5.5 -40 to +85 PWM or

PWM/PFM 500 19 350 Integrated synchronous boost regulator, 0.65V

start-up voltage, Soft start, True load disconnect

or input-to-output bypass option 6-pin SOT-23,

8-pin 2x3 DFN

MCP1650 Step-up DC/DC Controller 2.7 to 5.5 2.5 to ext. tx

limited -40 to +125 Constant frequency, 750 120 560/440 2 duty cycles for min. and max. loads, Shutdown

control, UVLO, Soft start 8-pin MSOP

MCP1651 Step-up DC/DC Controller 2.7 to 5.5 2.5 to ext. tx

limited -40 to +125 Constant frequency,

2 ﬁ xed DC 750 120 560/440 2 duty cycles for min. and max. loads, Shutdown

control, low battery detect, UVLO, Soft start 8-pin MSOP

MCP1652 Step-up DC/DC Controller 2.7 to 5.5 2.5 to ext. tx

limited -40 to +125 Constant frequency,

2 ﬁ xed DC 750 120 560/440 2 duty cycles for min. and max. loads, Shutdown

control, Power good indicator, UVLO, Soft start 8-pin MSOP

MCP1653 Step-up DC/DC Controller 2.7 to 5.5 2.5 to ext. tx

limited -40 to +125 Constant frequency,

2 ﬁ xed DC 750 120 560/440 2 duty cycles for min. and max. loads, Shutdown

control, Low battery detect, Power good indicator,

UVLO, Soft start 10-pin MSOP

MCP16301 30V Input Buck Regulator 4.0 to 30 2.0 to 15 -40 to +85 PWM 500 2000 600 Integrated N-channel, UVLO, Soft start,

Overtemperature protection SOT23-6

TC105 Step-down DC/DC Controller 2.2 to 10 3.0, 3.3, 5.0 -40 to +85 PFM/PWM 300 57 1,000 Low power shutdown mod 5-pin SOT-23A

TC115 Step-up DC/DC Regulator 0.9 to 10 3.0, 3.3, 5.0 -40 to +85 PFM/PWM 100 80 140 Feedback voltage sensing, Low power

shutdown mode 5-pin SOT-89

TC110 Step-up DC/DC Controller 2.0 to 10 3.0, 3.3, 5.0 -40 to +85 PFM/PWM 100/300 50/120 300 Soft start, Low power shutdown mode 5-pin SOT-23A

POWER MANAGEMENT – PWM Controllers

Part # Description Input

Voltage

Range (V)

Operating

Temperature

Range (°C)

Switching

Frequency

(kHz)

Typical

Active

Current (mA) Features Packages

MCP1630 Current mode, high-speed PWM to

use with PIC® MCUs 3.0 to 5.5 -40 to +125 1000 2.8 UVLO, Short circuit and Overtemperature protection,

Integrated MOSFET driver 8-pin MSOP, 8-pin 2x3 DFN

MCP1630V Voltage mode, high-speed PWM to

use with PIC® MCUs 3.0 to 5.5 -40 to +125 1000 2.8 UVLO, Short circuit and Overtemperature protection,

Integrated MOSFET driver 8-pin MSOP, 8-pin 2x3 DFN

MCP1631 Current mode, high-speed PWM to

use with PIC® MCUs 3.0 to 5.5 -40 to +125 2000 3.7 UVLO, Integrated error, current and voltage sense ampliﬁ ers,

Overvoltage comparator and MOSFET driver 20-pin SSOP, 20-pin TSSOP,

20-pin 4x4 QFN

MCP1631HV Current mode, high-speed PWM to

use with PIC® MCUs 3.5 to 16 -40 to +125 2000 3.7 Integrated 16V LDO, UVLO, Integrated error, Ccurrent and voltage

sense ampliﬁ ers, Overvoltage comparator and MOSFET driver 20-pin SSOP, 20-pin TSSOP

MCP1631V Voltage mode, high-speed PWM to

use with PIC® MCUs 3.0 to 5.5 -40 to +125 2000 3.7 UVLO, Integrated error, Current and voltage sense ampliﬁ ers,

Overvoltage comparator and MOSFET driver 20-pin SSOP, 20-pin TSSOP,

20-pin 4x4 QFN

MCP1631VHV Voltage mode, high-speed PWM to

use with PIC® MCUs 3.5 to 16 -40 to +125 2000 3.7 Integrated 16V LDO, UVLO, Integrated error, Current and voltage sense

ampliﬁ ers, Overvoltage comparator and MOSFET driver 20-pin SSOP, 20-pin TSSOP

POWER MANAGEMENT – Switching Regulator Combination Products

TC1303 Synchronous Buck Regulator,

LDO w/Power good 2.7 to 5.5 DC/DC: 0.8 to 4.5

LDO: 1.5 to 3.3 -40 to +85 PFM/PWM 2000 65/600 DC/DC: 500 mA

LDO: 300 mA PFM/PWM auto-switching, Power good output 10-pin MSOP,

10-pin 3x3 DFN

TC1304 Synchronous Buck Regulator,

LDO 2.7 to 5.5 DC/DC: 0.8 to 4.5

LDO: 1.5 to 3.3 -40 to +85 PFM/PWM 2000 65/600 DC/DC: 500 mA

LDO: 300 mA PFM/PWM auto-switching, Power sequencing 10-pin MSOP,

10-pin 3x3 DFN

TC1313 Synchronous Buck Regulator,

LDO 2.7 to 5.5 DC/DC: 0.8 to 4.5

LDO: 1.5 to 3.3 -40 to +85 PFM/PWM 2000 65/600 DC/DC: 500 mA

LDO: 300 mA PFM/PWM auto-switching 10-pin MSOP,

10-pin 3x3 DFN

Analog and Interface Product Selector Guide 10

POWER MANAGEMENT – Charge Pump DC-to-DC Converters

Part # Input

Voltage

Range (V) Output Voltage (V) Operating

Temperature

Range (°C) Maximum Input

Current(1) (μA) Typical Active

Output Current

(mA) Features Packages

Inverting or Doubling Charge Pumps

TC1044S 1.5 to 12 VOUT = -VIN or VOUT = 2 VIN -40 to +85 160 20 85 kHz oscillator, Boost mode 8-pin PDIP, 8-pin SOIC

TC7660 1.5 to 10 VOUT = -VIN or VOUT = 2 VIN -40 to +85 180 20 10 kHz oscillator 8-pin PDIP, 8-pin SOIC

TC7660H 1.5 to 10 VOUT = -VIN or VOUT = 2 VIN -40 to +85 1,000 20 120 kHz oscillator 8-pin PDIP, 8-pin SOIC

TC7660S 1.5 to 12 VOUT = -VIN or VOUT = 2 VIN -40 to +85 160 20 45 kHz oscillator, Boost mode 8-pin PDIP, 8-pin SOIC

TC7662B 1.5 to 15 VOUT = -VIN or VOUT = 2 VIN -40 to +85 180 20 35 kHz oscillator, Boost mode 8-pin PDIP, 8-pin SOIC

TC1240 2.5 to 4.0 VOUT = 2 VIN -40 to +85 900 40 Shutdown, 160 kHz oscillator 6-pin SOT-23A

TC1240A 2.5 to 5.5 VOUT = 2 VIN -40 to +85 900 40 Shutdown, 160 kHz oscillator 6-pin SOT-23A

TC7662A 3.0 to 18 VOUT = -VIN or VOUT = 2 VIN -40 to +85 200 40 12 kHz oscillator 8-pin PDIP, 8-pin SOIC

TC962 3.0 to 18 VOUT = -VIN or VOUT = 2 VIN -40 to +85 200 80 Selectable 12 kHz or 24 kHz oscillator 8-pin PDIP, 16-pin SOIC

Inverting and Doubling Charge Pumps

TC682 2.4 to 5.5 VOUT = -2 VIN -40 to +85 400 10 12 kHz oscillator 8-pin PDIP, 8-pin SOIC

Regulated Charge Pumps

MCP1252 2.1/2.7 to 5.5

2.0 to 5.5 Selectable 3.3V or 5.0V or

Adjustable 1.5V to 5.5V -40 to +85 120 120 mA for VIN>3.0V Power good output, 650 kHz oscillator 8-pin MSOP

MCP1253 2.1/2.7 to 5.5

2.0 to 5.5 Selectable 3.3V or 5.0V or

Adjustable 1.5V to 5.5V -40 to +85 120 120 mA for VIN>3.0V Power good output, 1 MHz oscillator 8-pin MSOP

MCP1256 1.8 to 3.6 3.3 -40 to +85 100 100 Power good, Sleep mode 10-pin MSOP, 10-pin 3x3 DFN

MCP1257 1.8 to 3.6 3.3 -40 to +85 100 100 Sleep mode, Low battery indication 10-pin MSOP, 10-pin 3x3 DFN

MCP1258 1.8 to 3.6 3.3 -40 to +85 100 100 Power good output, Input/output bypass 10-pin MSOP, 10-pin 3x3 DFN

MCP1259 1.8 to 3.6 3.3 -40 to +85 100 100 Low battery indication, Input/output bypass 10-pin MSOP, 10-pin 3x3 DFN

Note 1: Measured at VDD = 5.0V at 25°C and no load.

POWER MANAGEMENT – CPU/System Supervisors

Part # Vcc Range

(V) Operating

Temperature

Range (°C) Nominal Reset Voltage (V) Reset Type Output Typical Reset

Pulse Width

(ms)

Typical

Supply

Current (μA) Additional Features Packages Bond

Options

MCP102 1.0 to 5.5 -40 to +125 4.63, 4.38, 3.08, 2.93, 2.63, 2.32, 1.9 Active-Low CMOS Push-Pull 120 1 3-pin SOT-23B, 3-pin SC-70, 3-pin TO-92 N/A

MCP103 1.0 to 5.5 -40 to +125 4.63, 4.38, 3.08, 2.93, 2.63, 2.32, 1.9 Active-Low CMOS Push-Pull 120 1 Max. 809 Pinout 3-pin SOT-23B, 3-pin SC-70, 3-pin TO-92 N/A

MCP121 1.0 to 5.5 -40 to +125 4.63, 4.38, 3.08, 2.93, 2.63, 2.32, 1.9 Active-Low Open-Drain 120 1 3-pin SOT-23B, 3-pin SC-70, 3-pin TO-92 N/A

MCP131 1.0 to 5.5 -40 to +125 4.63, 4.38, 3.08, 2.93, 2.63, 2.32, 1.9 Active-Low Open-Drain 120 1 100 k Internal Pull-up

Resistor 3-pin SOT-23B, 3-pin SC-70, 3-pin TO-92 N/A

MCP1319 1.0 to 5.5 -40 to +125 4.6, 2.9(1) Active-Low/High CMOS Push-Pull 200 1 Manual Reset 5-pin SOT-23 N/A

MCP1322 1.0 to 5.5 -40 to +125 4.6, 2.9(1) Active-High Open-Drain/CMOS

Push-Pull 200 1 Manual Reset, two Reset

outputs

(Active-Low Open-Drain,

Active-High Push-Pull) 5-pin SOT-23 N/A

MCP1316 1.0 to 5.5 -40 to +125 4.6, 2.9(1) Active-Low CMOS Push-Pull 200 5 Watchdog Input (WDI),

Time-out = 1.6 sec.,

Manual Reset 5-pin SOT-23 N/A

MCP1317 1.0 to 5.5 -40 to +125 4.6, 2.9(1) Active-High CMOS Push-Pull 200 5 Watchdog Input (WDI),

Time-out = 1.6 sec.,

Manual Reset 5-pin SOT-23 N/A

MCP1318 1.0 to 5.5 -40 to +125 4.6, 2.9(1) Active-Low/High CMOS Push-Pull 200 5 Watchdog Input (WDI),

Time-out = 1.6 sec. 5-pin SOT-23 N/A

Note 1: Other reset voltage options available: 2.0V to 4.7V in 100 mV increments. Contact local Microchip sales ofﬁ ce.

Analog and Interface Product Selector Guide 11

POWER MANAGEMENT – CPU/System Supervisors (Continued)

Part # Vcc Range

(V) Operating

Temperature

Range (°C) Nominal Reset Voltage (V) Reset Type Output Typical Reset

Pulse Width

(ms)

Typical

Supply

Current (μA) Additional Features Packages Bond

Options

MCP1320 1.0 to 5.5 -40 to +125 4.6, 2.9(1) Active-Low Open-Drain 200 5 Watchdog Input (WDI),

Time-out = 1.6 sec.,

Manual Reset 5-pin SOT-23 N/A

MCP1321 1.0 to 5.5 -40 to +125 4.6, 2.9(1) Active-Low Open-Drain/CMOS

Push-Pull 200 5

Watchdog Input (WDI),

Time-out = 1.6 sec.,

Manual Reset

(Active-Low Open-Drain,

Active-High Push-Pull)

5-pin SOT-23 N/A

TC1270A 1.0 to 5.5 -40 to +125 4.63, 4.38, 3.08, 2.93, 2.63 Active-Low CMOS Push-Pull 280 7 Manual Reset 4-pin SOT-143, 5-pin SOT-23 N/A

TC1271A 1.0 to 5.5 -40 to +125 4.63, 4.38, 3.08, 2.93, 2.63 Active-High CMOS Push-Pull 280 7 Manual Reset 4-pin SOT-143, 5-pin SOT-23 N/A

TC1270AN 1.0 to 5.5 -40 to +125 4.63, 4.38, 3.08, 2.93, 2.63 Active-Low Open-Drain 0 7 Manual Reset 4-pin SOT-143, 5-pin SOT-23 N/A

TCM809 1.2 to 5.5 -40 to +85 4.63, 4.38, 4.00, 3.08, 2.93, 2.63, 2.32 Active-Low CMOS Push-Pull 240 12 3-pin SOT-23B, 3-pin SC-70 N/A

TCM810 1.2 to 5.5 -40 to +85 4.63, 4.38, 4.00, 3.08, 2.93, 2.63, 2.32 Active-High CMOS Push-Pull 240 12 3-pin SOT-23B, 3-pin SC-70 N/A

MCP100 1.0 to 5.5 -40 to +85 4.72, 4.62, 4.47, 4.37, 3.075, 2.92, 2.62 Active-Low CMOS Push-Pull 350 45 3-pin TO-92, 3-pin SOT-23B D, H

MCP809 1.0 to 5.5 -40 to +85 4.72, 4.62, 4.47, 4.37, 3.075, 2.92, 2.62 Active-Low CMOS Push-Pull 350 45 3-pin SOT-23B N/A

MCP101 1.0 to 5.5 -40 to +85 4.72, 4.62, 4.47, 4.37, 3.075, 2.92, 2.62 Active-High CMOS Push-Pull 350 45 3-pin TO-92, 3-pin SOT-23B D, H

MCP810 1.0 to 5.5 -40 to +85 4.72, 4.62, 4.47, 4.37, 3.075, 2.92, 2.62 Active-High CMOS Push-Pull 350 45 3-pin SOT-23B N/A

MCP120 1.0 to 5.5 -40 to +85 4.72, 4.62, 4.47, 4.37, 3.075, 2.92, 2.62 Active-Low Open-Drain 350 45 3-pin TO-92, 3-pin SOT-23, 8-pin

SOIC D, G, H

MCP130 1.0 to 5.5 -40 to +85 4.72, 4.62, 4.47, 4.37, 3.075, 2.92, 2.62 Active-Low Open-Drain

w/5 kOhm Pull-up 350 45 3-pin TO-92, 3-pin SOT-23, 8-pin

SOIC D, F, H

TC1232 4.5 to 5.5 -40 to +85 4.62, 4.37 Active-Low/High Open-Drain 610 50 Watchdog Timer 8-pin PDIP, 8-pin SOIC,

16-pin SOIC N/A

TC32M 4.5 to 5.5 -40 to +85 4.5 Active-Low Open-Drain 700 50 Watchdog Timer 3-pin TO-92, 3-pin SOT-223 N/A

Note 1: Other reset voltage options available: 2.0V to 4.7V in 100 mV increments. Contact local Microchip sales ofﬁ ce.

POWER MANAGEMENT – Voltage Detectors

Part # Vcc Range

(V)

Operating

Temperature

Range (°C) Nominal Reset Voltage (V) Reset Type Output Minimum

Reset Pulse

Width (ms)

Typical

Supply

Current (μA) Features Packages

MCP111 1.0 to 5.5 -40 to +125 4.63, 4.38, 3.08, 2.93, 2.63, 2.32, 1.90 Active-Low Open-Drain – 1 3-pin SOT-23B, 3-pin TO-92, 3-pin SC-70, 3-pin SOT-89

MCP112 1.0 to 5.5 -40 to +125 4.63, 4.38, 3.08, 2.93, 2.63, 2.32, 1.90 Active-Low CMOS Push-Pull – 1 3-pin SOT-23B, 3-pin TO-92, 3-pin SC-70, 3-pin SOT-89

TC52 1.5 to 10 -40 to +85 4.5/2.7, 3.0/2.7 Active-Low Open-Drain – 2 Dual channel 5-pin SOT-23A

TC54 0.7 to 10 -40 to +85 4.3, 4.2, 3.0, 2.9, 2.7, 2.1, 1.4 Active-Low CMOS Push-Pull or

Open-Drain – 1 3-pin SOT-23A, 3-pin SOT-89, 3-pin TO-92

Analog and Interface Product Selector Guide 12

POWER MANAGEMENT – Power MOSFET Drivers

Part # Conﬁ guration Operating

Temperature

Range (°C)

Peak Output

Current (A)

Output Resistance

(RH/RL)

(Max.  @ 25°C)

Maximum Supply

Voltage (V) Input/Output Delay

(tD1, tD2)(1) (ns) Packages

Low-Side Drivers, 0.5A to 1.2A Peak Output Current

MCP1401 Single, Inverting -40 to +125 0.5 18/16 18 40/40 5-pin SOT-23

MCP1402 Single, Non-inverting -40 to +125 0.5 18/16 18 40/40 5-pin SOT-23

TC1410 Single, Inverting -40 to +85 0.5 22/22 16 30/30 8-pin PDIP, 8-pin SOIC, 8-pin MSOP

TC1410N Single, Non-inverting -40 to +85 0.5 22/22 16 30/30 8-pin PDIP, 8-pin SOIC, 8-pin MSOP

TC1411 Single, Inverting -40 to +85 1.0 11/11 16 30/30 8-pin PDIP, 8-pin SOIC, 8-pin MSOP

TC1411N Single, Non-inverting -40 to +85 1.0 11/11 16 30/30 8-pin PDIP, 8-pin SOIC, 8-pin MSOP

TC1426 Dual, Inverting 0 to +70 1.2 18/18 16 75/75 8-pin PDIP, 8-pin SOIC

TC1427 Dual, Non-inverting 0 to +70 1.2 18/18 16 75/75 8-pin PDIP, 8-pin SOIC

TC1428 Dual, Inverting and Non-inverting 0 to +70 1.2 18/18 16 75/75 8-pin PDIP, 8-pin SOIC

TC4467 Quad, Inverting -40 to +85 1.2 15/15 18 40/40 14-pin PDIP, 16-pin SOIC (W)

TC4468 Quad, Non-inverting -40 to +85 1.2 15/15 18 40/40 14-pin PDIP, 16-pin SOIC (W)

TC4469 Quad, Non-inverting -40 to +85 1.2 15/15 18 40/40 14-pin PDIP, 16-pin SOIC (W)

Low-Side Drivers, 1.5A Peak Output Current

MCP1415 Single, Inverting -40 to +125 1.5 7.5/5.5 18 50/55 5-pin SOT-23

MCP1416 Single, Non-inverting -40 to +125 1.5 7.5/5.5 18 50/55 5-pin SOT-23

TC4403 Single, Non-inverting Floating Load Driver -40 to +85 1.5 5/5 18 33/38 8-pin PDIP

TC4404 Dual, Inverting -40 to +85 1.5 10/10 18 15/32 8-pin PDIP, 8-pin SOIC

TC4405 Dual, Non-inverting -40 to +85 1.5 10/10 18 15/32 8-pin PDIP, 8-pin SOIC

TC4426A Dual, Inverting -40 to +125 1.5 9/9 18 30/30 8-pin PDIP, 8-pin SOIC, 8-pin DFN

TC4427A Dual, Non-inverting -40 to +125 1.5 9/9 18 30/30 8-pin PDIP, 8-pin SOIC, 8-pin DFN

TC4428A Dual, Inverting and Non-inverting -40 to +125 1.5 9/9 18 30/30 8-pin PDIP, 8-pin SOIC, 8-pin DFN

TC4426 Dual, Inverting -40 to +125 1.5 10/10 18 20/40 8-pin PDIP, 8-pin SOIC, 8-pin DFN, 8-pin MSOP

TC4427 Dual, Non-inverting -40 to +125 1.5 10/10 18 20/40 8-pin PDIP, 8-pin SOIC, 8-pin DFN, 8-pin MSOP

TC4428 Dual, Inverting and Non-inverting -40 to +125 1.5 10/10 18 20/40 8-pin PDIP, 8-pin SOIC, 8-pin DFN, 8-pin MSOP

TC426 Dual, Inverting -40 to +85 1.5 15/10 18 50/75 8-pin PDIP, 8-pin SOIC

TC427 Dual, Non-inverting -40 to +85 1.5 15/10 18 50/75 8-pin PDIP, 8-pin SOIC

TC428 Dual, Inverting and Non-inverting -40 to +85 1.5 15/10 18 50/75 8-pin PDIP, 8-pin SOIC

TC1412 Single, Inverting -40 to +85 2 6/6 16 35/35 8-pin PDIP, 8-pin SOIC, 8-pin MSOP

TC1412N Single, Non-inverting -40 to +85 2 6/6 16 35/35 8-pin PDIP, 8-pin SOIC, 8-pin MSOP

MCP14E6 Dual, Inverting -40 to +125 2 2.2/2.8 18 45/45 8-pin PDIP, 8-pin SOIC, 8-pin DFN

MCP14E7 Dual, Non-inverting -40 to +125 2 2.2/2.8 18 45/45 8-pin PDIP, 8-pin SOIC, 8-pin DFN

MCP14E8 Dual, Inverting and Non-inverting -40 to +125 2 2.2/2.8 18 45/45 8-pin PDIP, 8-pin SOIC, 8-pin DFN

MCP14E9 Dual, Inverting -40 to +125 3 2.2/2.8 18 75/75 8-pin PDIP, 8-pin SOIC, 8-pin DFN

MCP14E10 Dual, Non-inverting -40 to +125 3 2.2/2.8 18 75/75 8-pin PDIP, 8-pin SOIC, 8-pin DFN

MCP14E11 Dual, Inverting and Non-inverting -40 to +125 3 2.2/2.8 18 75/75 8-pin PDIP, 8-pin SOIC, 8-pin DFN

Note 1: tD1 = delay time from input low-to-high transition to output transition. tD2 = delay time from input high-to-low transition to output transition.

Analog and Interface Product Selector Guide 13

POWER MANAGEMENT – Power MOSFET Drivers (Continued)

Part # Conﬁ guration Operating

Temperature

Range (°C) Peak Output

Current (A) Output Resistance

(RH/RL)

(Max.  @ 25°C) Maximum Supply

Voltage (V) Input/Output Delay

(tD1, tD2)(1) (ns) Packages

Low-Side Drivers, 2.0A to 12.0A Peak Output Current

TC1413 Single, Inverting -40 to +85 3 4/4 16 35/35 8-pin PDIP, 8-pin SOIC, 8-pin MSOP

TC1413N Single, Non-inverting -40 to +85 3 4/4 16 35/35 8-pin PDIP, 8-pin SOIC, 8-pin MSOP

TC4423A Dual, Inverting -40 to +125 3 3 (typ)/4 (typ) 18 40 (typ)/40 (typ) 8-pin PDIP, 8-pin SOIC, 8-pin DFN

TC4424A Dual, Non-inverting -40 to +125 3 3 (typ)/4 (typ) 18 40 (typ)/40 (typ) 8-pin PDIP, 8-pin SOIC, 8-pin DFN

TC4425A Dual, Inverting and Non-inverting -40 to +125 3 3 (typ)/4 (typ) 18 40 (typ)/40 (typ) 8-pin PDIP, 8-pin SOIC, 8-pin DFN

TC4423 Dual, Inverting -40 to +125 3 5/5 18 33/38 8-pin PDIP, 16-pin SOIC (W), 8-pin DFN

TC4424 Dual, Non-inverting -40 to +125 3 5/5 18 33/38 8-pin PDIP, 16-pin SOIC (W), 8-pin DFN

TC4425 Dual, Inverting and Non-inverting -40 to +125 3 5/5 18 33/38 8-pin PDIP, 16-pin SOIC (W), 8-pin DFN

MCP14E3 Dual, Inverting -40 to +125 4.0 3.5/3.0 18 55/55 8-pin PDIP, 8-pin SOIC, 8-pin 6x5 DFN

MCP14E4 Dual, Non-inverting -40 to +125 4.0 3.5/3.0 18 55/55 8-pin PDIP, 8-pin SOIC, 8-pin 6x5 DFN

MCP14E5 Dual, Inverting and Non-inverting -40 to +125 4.0 3.5/3.0 18 55/55 8-pin PDIP, 8-pin SOIC, 8-pin 6x5 DFN

MCP1403 Dual, Inverting -40 to +125 4.5 3/3.5 18 48/48 8-pin PDIP, 8-pin SOIC, 8-pin 6x5 DFN, 16-pin SOIC

MCP1404 Dual, Non-inverting -40 to +125 4.5 3/3.5 18 48/48 8-pin PDIP, 8-pin SOIC, 8-pin 6x5 DFN, 16-pin SOIC

MCP1405 Dual, Inverting and Non-inverting -40 to +125 4.5 3/3.5 18 48/48 8-pin PDIP, 8-pin SOIC, 8-pin 6x5 DFN, 16-pin SOIC

MCP1406 Single, Inverting -40 to +125 6 1.8 (typ)/2.0 (typ) 18 30/30 5-pin TO-220, 8-pin PDIP, 8-pin 6x5 DFN, 8-pin SOIC

MCP1407 Single, Non-inverting -40 to +125 6 1.8 (typ)/2.0 (typ) 18 30/30 5-pin TO-220, 8-pin PDIP, 8-pin 6x5 DFN, 8-pin SOIC

TC429 Single, Inverting -40 to +85 6 2.5/2.5 18 53/60 8-pin PDIP, 8-pin DFN, 8-pin SOIC

TC4420 Single, Non-inverting -40 to +125 6 2.8/2.5 18 55/55 8-pin PDIP, 8-pin SOIC, 5-pin TO-220, 8-pin DFN

TC4429 Single, Inverting -40 to +125 6 2.8/2.5 18 55/55 8-pin PDIP, 8-pin SOIC, 5-pin TO-220, 8-pin DFN

TC4421 Single, Inverting -40 to +125 9 1.4 (typ)/1.7 18 30/33 8-pin PDIP, 5-pin TO-220, 8-pin DFN

TC4421A Single, Inverting -40 to +125 9 1.25 (typ)/1.5 18 38/42 8-pin PDIP, 8-pin SOIC, 5-pin TO-220, 8-pin 6x5 DFN

TC4422 Single, Non-inverting -40 to +125 9 1.4 (typ)/1.7 18 30/33 8-pin PDIP, 5-pin TO-220, 8-pin DFN

TC4422A Single, Non-inverting -40 to +125 9 1.25 (typ)/1.5 18 38/42 8-pin PDIP, 8-pin SOIC, 5-pin TO-220, 8-pin 6x5 DFN

TC4451 Single, Inverting -40 to +125 12 0.6 (typ)/1.5 18 15/15 8-pin SOIC, 8-pin PDIP, 8-pin 6x5 DFN, 5-pin TO-220, 5-pin DDPAK

TC4452 Single, Non-inverting -40 to +125 12 0.6 (typ)/1.5 18 15/15 8-pin SOIC, 8-pin PDIP, 8-pin 6x5 DFN, 5-pin TO-220, 5-pin DDPAK

High-Side/Low-Side Drivers

TC4626 Single, Inverting -40 to +85 1.5 15/10 6 35/45 8-pin PDIP, 16-pin SOIC (W)

TC4627 Single, Non-inverting -40 to +85 1.5 15/10 6 35/45 8-pin PDIP, 16-pin SOIC (W)

TC4431 Single, Inverting -40 to +85 1.5 10/10 30 62/78 8-pin PDIP, 8-pin SOIC

TC4432 Single, Non-inverting -40 to +85 1.5 10/10 30 62/78 8-pin PDIP, 8-pin SOIC

Synchronous Buck High-Side Drivers

MCP14628 Dual, Non-inverting -40 to +85 2 2.5/2.5 5 (VDD), 36 (Boot Pin) 18/20 8-pin SOIC, 8-pin 3x3 DFN

MCP14700 Dual, Non-inverting -40 to +125 2 2.5/2.5 5 (VDD), 36 (Boot Pin) 25/25 8-pin SOIC, 8-pin 3x3 DFN

Note 1: tD1 = delay time from input low-to-high transition to output transition. tD2 = delay time from input high-to-low transition to output transition.

Analog and Interface Product Selector Guide 14

POWER MANAGEMENT – Battery Chargers

Part # Mode Cell Type # of

Cells Vcc

Range (V) Cell

Voltage (V) Maximum

Charging

Current (mA)

Max. Voltage

Regulation

(%) Int/Ext

FET Features Packages

MCP73113 Linear Li-ion/Li-Polymer 1 4 to 16 4.1, 4.2, 4.35, 4.4 1100 ±0.5 Int 6.5V Overvoltage Protection 10-pin 3x3 DFN

MCP73114 Linear Li-ion/Li-Polymer 1 4 to 16 4.1, 4.2, 4.35, 4.4 1100 ±0.5 Int 5.8V Overvoltage Protection 10-pin 3x3 DFN

MCP73123 Linear LiFePO4 1 4 to 16 3.6 1100 ±0.5 Int 6.5V Overvoltage Protection, LiFePO4 charging 10-pin 3x3 DFN

MCP73213 Linear Li-ion/Li-Polymer 2 4 to 16 8.2, 8.4, 8.7, 8.8 1100 ±0.6 Int 13V Overvoltage Protection 10-pin 3x3 DFN

MCP73223 Linear LiFePO4 2 4 to 16 7.2 1100 ±0.6 Int 13V Overvoltage Protection, LiFePO4 charging 10-pin 3x3 DFN

MCP73826 Linear Li-Ion/Li-Polymer 1 4.5 to 5.5 4.1, 4.2 N/A ±1.0 Ext Small size, charge current set by external FET 6-pin SOT-23

MCP73827 Linear Li-Ion/Li-Polymer 1 4.5 to 5.5 4.1, 4.2 N/A ±1.0 Ext Mode indicator, Charge current monitor, Charge current set by external

FET 8-pin MSOP

MCP73828 Linear Li-Ion/Li Polymer 1 4.5 to 5.5 4.1, 4.2 N/A ±1.0 Ext Temperature monitor, Charge current set by external FET 8-pin MSOP

MCP73841 Linear Li-Ion/Li-Polymer 1 4.5 to 12 4.1, 4.2 N/A ±0.5 Ext Safety charge timers, Temperature monitor, Charge current set by

external FET 10-pin MSOP

MCP73842 Linear Li-Ion/Li-Polymer 2 8.7 to 12 8.2, 8.4 N/A ±0.5 Ext Safety charge timers, Temperature monitor, Charge current set by

external FET 10-pin MSOP

MCP73843 Linear Li-Ion/Li-Polymer 1 4.5 to 12 4.1, 4.2 N/A ±0.5 Ext Safety charge timers, Charge current set by external FET 8-pin MSOP

MCP73844 Linear Li-Ion/Li-Polymer 2 8.7 to 12 8.2, 8.4 N/A ±0.5 Ext Safety charge timers, Charge current set by external FET 8-pin MSOP

MCP73811 Linear Li-Ion/Li-Polymer 1 3.7 to 6.0 4.2 500 ±1.0 Int Selectable charge current (100 mA, 500 mA), Charge enable input 5-pin SOT-23

MCP73812 Linear Li-Ion/Li Polymer 1 3.7 to 6.0 4.2 500 ±1.0 Int Programmable charge current (100 mA, 500 mA), Charge enable input 5-pin SOT-23

MCP73831 Linear Li-Ion/Li-Polymer 1 3.7 to 6.0 4.2, 4.35, 4.4, 4.5 500 ±0.75 Int UVLO, Thermal regulation, Programmable charge current,

Tri-state STAT pin 5-pin SOT-23, 8-pin

2x3 DFN

MCP73832 Linear Li-Ion/Li-Polymer 1 3.7 to 6.0 4.2, 4.35, 4.4, 4.5 500 ±0.75 Int UVLO, Thermal regulation, Programmable charge current,

Open-drain STAT pin 5-pin SOT-23, 8-pin

2x3 DFN

MCP73853 Linear Li-Ion/Li-Polymer 1 4.5 to 5.5 4.1, 4.2 500 ±0.5 Int USB control, Safety charge timers, Temperature monitor,

Thermal regulation 16-pin 4x4 QFN

MCP73855 Linear Li-Ion/Li-Polymer 1 4.5 to 5.5 4.1, 4.2 500 ±0.5 Int USB control, Safety charge timers, Thermal regulation 10-pin 3x3 DFN

MCP73833 Linear Li-Ion/Li-Polymer 1 3.7 to 6.0 4.2, 4.35, 4.4, 4.5 1000 ±0.75 Int UVLO, Thermal regulation, Thermistor input, LDO Test mode,

Multiple VREG outputs, Safety timer, Power good output 10-pin 3x3 DFN,

10-pin MSOP

MCP73834 Linear Li-Ion/Li-Polymer 1 3.7 to 6.0 4.2, 4.35, 4.4, 4.5 1000 ±0.75 Int UVLO, Thermal regulation, Thermistor input, LDO Test mode,

Multiple VREG outputs, Safety timer, Timer enable input 10-pin 3x3 DFN,

10-pin MSOP

MCP73837 Linear Li-Ion/Li-Polymer 1 3.7 to 6.0 4.2, 4.35, 4.4, 4.5 1000 ±0.75 Int Dual input (USB, DC input from adapter) auto-switching, UVLO,

Thermal regulation, Thermistor input, Power good output 10-pin 3x3 DFN,

10-pin MSOP

MCP73838 Linear Li-Ion/Li Polymer 1 3.7 to 6.0 4.2, 4.35, 4.4, 4.5 1000 ±0.75 Int Dual input (USB, DC input from adapter) auto-switching, UVLO,

Thermal regulation, Timer enable input 10-pin 3x3 DFN,

10-pin MSOP

MCP73861 Linear Li-Ion/Li-Polymer 1 4.5 to 12 4.1, 4.2 1000 ±0.5 Int Safety charge timers, Temperature monitor, Thermal regulation,

Flashing STAT1 output on charge complete 16-pin 4x4 QFN,

16-pin SOIC

MCP73862 Linear Li-Ion/Li-Polymer 2 8.7 to 12 8.2, 8.4 1000 ±0.5 Int Safety charge timers, Temperature monitor, Thermal regulation,

hi-Z STAT1 output on charge complete 16-pin 4x4 QFN,

16-pin SOIC

MCP73863 Linear Li-Ion/Li-Polymer 1 4.5 to 12 4.1, 4.2 1000 ±0.5 Int Safety charge timers, Temperature monitor, Thermal regulation,

hi-Z STAT1 output on charge complete 16-pin 4x4 QFN,

16-pin SOIC

MCP73864 Linear Li-Ion/Li-Polymer 2 8.7 to 12 8.2, 8.4 1000 ±0.5 Int Safety charge timers, Temperature monitor, Thermal regulation,

hi-Z STAT1 output on charge complete 16-pin 4x4 QFN,

16-pin SOIC

MCP73871 Linear Li-Ion/Li-Polymer 1 3.75 to 6.0 4.2, 4.35, 4.4 1500 (A/C Adapter)

500 (USB) ±0.5 Int Simultaneous charging of load and battery, Load-dependent charging,

Multiple programmable charge currents 20-pin 4x4 QFN,

20-pin SSOP

POWER MANAGEMENT – Hot Swap Controllers

Part # Number of

Outputs VPOS to VNEG

Differential Voltage

(V) Junction Temperature

Range (°C) OVLO UVLO Power good Int/Ext FET Applications Packages

MCP18480 1 -0.3 to +15.0 -40 to +85 Adjustable Adjustable Adjustable Ext -48V Telecom/Datacom, Bus/Backplane 20-pin SSOP

Analog and Interface Product Selector Guide 15

LINEAR

LINEAR – Op Amps

Part # # per

Package GBWP IQ Typical

(μA) VOS Max

(mV) Typical Input

Bias Current

(pA)

Input Voltage

Noise Density

(nV/rtHz) Operating

Voltage (V) Temperature

Range (°C) Features Packages

MCP6441 1 9 kHz 0.45 4.5 1 190(1) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 5-pin SOT-23(S), 5-pin SC-70(S)

MCP6442 2 9 kHz 0.45 4.5 1 190(1) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin MSOP, 8-pin 2x3 TDFN

MCP6444 4 9 kHz 0.45 4.5 1 190(1) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 14-pin SOIC, 14-pin TSSOP

MCP6031 1 10 kHz 0.9 0.15 1 165(1) 1.8 to 5.5 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin MSOP, 8-pin 2x3 DFN, 5-pin SOT-23

MCP6032 2 10 kHz 0.9 0.15 1 165(1) 1.8 to 5.5 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin MSOP

MCP6033 1 10 kHz 0.9 0.15 1 165(1) 1.8 to 5.5 -40 to +125 Rail-to-Rail Input/Output, Chip select 8-pin SOIC, 8-pin MSOP, 8-pin 2x3 DFN

MCP6034 4 10 kHz 0.9 0.15 1 165(1) 1.8 to 5.5 -40 to +125 Rail-to-Rail Input/Output 14-pin SOIC, 14-pin TSSOP

MCP6041 1 14 kHz 0.6 3 1 170(1) 1.4 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 5-pin SOT-23(S)

MCP6042 2 14 kHz 0.6 3 1 170(1) 1.4 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin PDIP, 8-pin SOIC, 8-pin MSOP

MCP6043 1 14 kHz 0.6 3 1 170(1) 1.4 to 6.0 -40 to +125 Rail-to-Rail Input/Output, Chip select 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 6-pin SOT-23(S)

MCP6044 4 14 kHz 0.6 3 1 170(1) 1.4 to 6.0 -40 to +125 Rail-to-Rail Input/Output 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP

MCP6141 1 100 kHz 0.6 3 1 170(1) 1.4 to 6.0 -40 to +125 Rail-to-Rail Input/Output, G>10 stable 5-pin SOT-23(S), 8-pin PDIP, 8-pin SOIC, 8-pin MSOP

MCP6142 2 100 kHz 0.6 3 1 170(1) 1.4 to 6.0 -40 to +125 Rail-to-Rail Input/Output, G>10 stable 8-pin PDIP, 8-pin SOIC, 8-pin MSOP

MCP6143 1 100 kHz 0.6 3 1 170(1) 1.4 to 6.0 -40 to +125 Rail-to-Rail Input/Output, G>10 stable,

Chip select 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 6-pin SOT-23(S),

MCP6144 4 100 kHz 0.6 3 1 170(1) 1.4 to 6.0 -40 to +125 Rail-to-Rail Input/Output, G>10 stable 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP

MCP606 1 155 kHz 19 0.25 1 38(1) 2.5 to 6.0 -40 to +125 Rail-to-Rail Output 8-pin PDIP, 8-pin SOIC, 8-pin TSSOP, 5-pin SOT23(S)

MCP607 2 155 kHz 19 0.25 1 38(1) 2.5 to 6.0 -40 to +85 Rail-to-Rail Output 8-pin PDIP, 8-pin SOIC, 8-pin TSSOP

MCP608 1 155 kHz 19 0.25 1 38(1) 2.5 to 6.0 -40 to +85 Rail-to-Rail Output, Chip select 8-pin PDIP, 8-pin SOIC, 8-pin TSSOP

MCP609 4 155 kHz 19 0.25 1 38(1) 2.5 to 6.0 -40 to +85 Rail-to-Rail Output 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP

MCP616 1 190 kHz 19 0.15 15000 32(1) 2.3 to 5.5 -40 to +85 Rail-to-Rail Output, PNP input 8-pin PDIP, 8-pin SOIC, 8-pin MSOP

MCP617 2 190 kHz 19 0.15 15000 32(1) 2.3 to 5.5 -40 to +85 Rail-to-Rail Output, PNP input 8-pin PDIP, 8-pin SOIC, 8-pin MSOP

MCP618 1 190 kHz 19 0.15 15000 32(1) 2.3 to 5.5 -40 to +85 Rail-to-Rail Output, Chip select, PNP input 8-pin PDIP, 8-pin SOIC, 8-pin MSOP

MCP619 4 190 kHz 19 0.15 15000 32(1) 2.3 to 5.5 -40 to +85 Rail-to-Rail Output, PNP input 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP

MCP6231 1 300 kHz 20 5 1 52(1) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin 2x3 TDFN,

5-pin SC-70(U), 5-pin SOT-23(S,R,U)

MCP6232 2 300 kHz 20 5 1 52(1) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin 2x3 TDFN

MCP6234 4 300 kHz 20 5 1 52(1) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP

MCP6051 1 385 kHz 30 0.15 1 34(2) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin 2x3 DFN, 5-pin SOT-23(S)

MCP6052 2 385 kHz 30 0.15 1 34(2) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin 2x3 DFN

MCP6054 4 385 kHz 30 0.15 1 34(2) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 14-pin SOIC, 14-pin TSSOP

MCP6241 1 550 kHz 50 5 1 45

(1)

1.8 to 5.5 -40 to +125 Rail-to-Rail Input/Output 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin 2x3

TDFN, 5-pin SC-70

(U)

, 5-pin SOT-23

(S,R,U)

MCP6242 2 550 kHz 50 5 1 45

(1)

1.8 to 5.5 -40 to +125 Rail-to-Rail Input/Output 8-pin PDIP, 8-pin SOIC, 8-pin MSOP

MCP6244 4 550 kHz 50 5 1 45(1) 1.8 to 5.5 -40 to +125 Rail-to-Rail Input/Output 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP

MCP6061 1 730 kHz 60 0.15 1 25(2) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin 2x3 DFN, 5-pin SOT-23(S)

MCP6062 2 730 kHz 60 0.15 1 25(2) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin 2x3 DFN

MCP6064 4 730 kHz 60 0.15 1 25(2) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 14-pin SOIC, 14-pin TSSOP

MCP6001 1 1 MHz 100 4.5 1 28(1) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 5-pin SOT-23(S,R,U), 5-pin SC-70(R)

MCP6002 2 1 MHz 100 4.5 1 28(1) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin 2x3 DFN

Legend: S = Standard Pinout; R = Reverse Pinout; U = Alternative Pinout

Note 1: Values are typical at 1 kHz

2: Values are typical at 10 kHz

Analog and Interface Product Selector Guide 16

LINEAR – Op Amps (Continued)

Part # # per

Package GBWP IQ Typical

(μA) Vos Max

(mV) Typical Input

Bias Current

(pA)

Input Voltage

Noise Density

(nV/rtHz) Operating

Voltage (V) Temperature

Range (°C) Features Packages

MCP6004 4 1 MHz 100 4.5 1 28(1) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP

MCP6401 1 1 MHz 45 4.5 1 28(1) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 5-pin SOT-23(S,R,U), 5-pin SC-70(R)

MCP6402 2 1 MHz 45 4.5 1 28(1) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin 2x3 TDFN

MCP6404 4 1 MHz 45 4.5 1 28(1) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 14-pin SOIC, 14-pin TSSOP

MCP6L01 1 1 MHz 85 5 2 24(2) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 5-pin SOT-23(S,R,U), 5-pin SC-70(S)

MCP6L02 2 1 MHz 85 5 2 24(2) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin MSOP

MCP6L04 4 1 MHz 85 5 2 24(2) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 14-pin SOIC, 14-pin TSSOP

MCP6071 1 1.2 MHz 110 0.15 1 19(2) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin 2x3 DFN, 5-pin SOT-23(S)

MCP6072 2 1.2 MHz 110 0.15 1 19(2) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin 2x3 DFN

MCP6074 4 1.2 MHz 110 0.15 1 19(2) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 14-pin SOIC, 14-pin TSSOP

MCP6H01 1 1.2 MHz 135 3.5 10 35(1) Single Supply: 3.5 to 16

Dual Supply: ±1.75 to ±8 -40 to +125 Rail-to-Rail Output 8-pin SOIC, 8-pin 2x3 TDFN

MCP6H02 2 1.2 MHz 135 3.5 10 35(1) Single Supply: 3.5 to 16

Dual Supply: ±1.75 to ±8 -40 to +125 Rail-to-Rail Output 8-pin SOIC, 8-pin 2x3 TDFN

MCP6H04 4 1.2 MHz 135 3.5 10 35(1) Single Supply: 3.5 to 16

Dual Supply: ±1.75 to ±8 -40 to +125 Rail-to-Rail Output 14-pin SOIC, 14-pin TSSOP

MCP6271 1 2 MHz 170 3 1 20(1) 2.0 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin PDIP, 8-pin SOIC, 8-pin MSOP,

5-pin SOT-23(S,R),

MCP6272 2 2 MHz 170 3 1 20(1) 2.0 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin PDIP, 8-pin SOIC, 8-pin MSOP

MCP6273 1 2 MHz 170 3 1 20(1) 2.0 to 6.0 -40 to +125 Rail-to-Rail Input/Output, Chip select 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 6-pin SOT-23(S)

MCP6274 4 2 MHz 170 3 1 20(1) 2.0 to 6.0 -40 to +125 Rail-to-Rail Input/Output 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP

MCP6275 2 2 MHz 150 3 1 20(1) 2.0 to 6.0 -40 to +125 Rail-to-Rail Input/Output,

Dual connected, Chip select 8-pin PDIP, 8-pin SOIC, 8-pin MSOP

MCP6L71 1 2 MHz 150 4 1 19(2) 2.0 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC(S), 8-pin MSOP(S), 5-pin SOT-23(S,R)

MCP6L72 2 2 MHz 150 4 1 19(2) 2.0 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin MSOP

MCP6L74 4 2 MHz 150 4 1 19(2) 2.0 to 6.0 -40 to +125 Rail-to-Rail Input/Output 14-pin SOIC, 14-pin TSSOP

MCP601 1 2.8 MHz 230 2 1 29(1) 2.7 to 6.0 -40 to +125 Rail-to-Rail Output 8-pin PDIP, 8-pin SOIC, 8-pin TSSOP,

5-pin SOT-23(S,R)

MCP602 2 2.8 MHz 230 2 1 29(1) 2.7 to 6.0 -40 to +125 Rail-to-Rail Output 8-pin PDIP, 8-pin SOIC, 8-pin TSSOP

MCP603 1 2.8 MHz 230 2 1 29(1) 2.7 to 6.0 -40 to +125 Rail-to-Rail Output, Chip select 8-pin PDIP, 8-pin SOIC, 8-pin TSSOP, 6-pin SOT-23(S)

MCP604 4 2.8 MHz 230 2 1 29(1) 2.7 to 6.0 -40 to +125 Rail-to-Rail Output 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP

MCP6L1 1 2.8 MHz 200 3 1 21(2) 2.7 to 6.0 -40 to +125 Rail-to-Rail Output 8-pin SOIC(S), 8-pin MSOP(S), 5-pin SOT-23(S,R)

MCP6L2 2 2.8 MHz 200 3 1 21(2) 2.7 to 6.0 -40 to +125 Rail-to-Rail Output 8-pin SOIC, 8-pin MSOP

MCP6L4 4 2.8 MHz 200 3 1 21(2) 2.7 to 6.0 -40 to +125 Rail-to-Rail Output 14-pin SOIC, 14-pin TSSOP

MCP6281 1 5 MHz 445 3 1 16(1) 2.2 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 5-pin SOT-23(S,R)

MCP6282 2 5 MHz 445 3 1 16(1) 2.2 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin PDIP, 8-pin SOIC, 8-pin MSOP

MCP6283 1 5 MHz 445 3 1 16(1) 2.2 to 6.0 -40 to +125 Rail-to-Rail Input/Output, Chip select 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 6-pin SOT-23(S,R)

MCP6284 4 5 MHz 445 3 1 16(1) 2.2 to 6.0 -40 to +125 Rail-to-Rail Input/Output 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP

MCP6285 2 5 MHz 400 3 1 16(1) 2.2 to 6.0 -40 to +125 Rail-to-Rail Input/Output, Dual connected,

Chip select 8-pin PDIP, 8-pin SOIC, 8-pin MSOP

MCP6286 1 3.5 MHz 540 1.5 1 5.4(2) 2.2 to 5.5 -40 to +125 Rail-to-Rail Output, Low noise 5-pin SOT-23(S,R)

MCP6021 1 10 MHz 1000 0.5 1 8.7(2) 2.5 to 5.5 -40 to +125 Rail-to-Rail Input/Output, 1/2 VCC VREF 8-pin PDIP, 8-pin SOIC, 8-pin TSSOP, 8-pin MSOP,

5-pin SOT-23(S,R)

Legend: S = Standard Pinout; R = Reverse Pinout; U = Alternative Pinout

Note 1: Values are typical at 1 kHz

2: Values are typical at 10 kHz

Analog and Interface Product Selector Guide 17

LINEAR – Op Amps (Continued)

Part # # per

Package GBWP IQ Typical

(μA) Vos Max

(mV) Typical Input

Bias Current

(pA)

Input Voltage

Noise Density

(nV/rtHz) Operating

Voltage (V) Temperature

Range (°C) Features Packages

MCP6022 2 10 MHz 1000 0.5 1 8.7(2) 2.5 to 5.5 -40 to +125 Rail-to-Rail Input/Output 8-pin PDIP, 8-pin SOIC, 8-pin TSSOP

MCP6023 1 10 MHz 1000 0.5 1 8.7(2) 2.5 to 5.5 -40 to +125 Rail-to-Rail Input/Output, Chip select,

1/2 VCC VREF 8-pin PDIP, 8-pin SOIC, 8-pin TSSOP

MCP6024 4 10 MHz 1000 0.5 1 8.7(2) 2.5 to 5.5 -40 to +125 Rail-to-Rail Input/Output 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP

MCP6291 1 10 MHz 1000 3 1 8.7(2) 2.4 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 5-pin SOT-23(S,R)

MCP6292 2 10 MHz 1000 3 1 8.7(2) 2.4 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin PDIP, 8-pin SOIC, 8-pin MSOP

MCP6293 1 10 MHz 1000 3 1 8.7(2) 2.4 to 6.0 -40 to +125 Rail-to-Rail Input/Output, Chip select 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 6-pin SOT-23(S)

MCP6294 4 10 MHz 1000 3 1 8.7(2) 2.4 to 6.0 -40 to +125 Rail-to-Rail Input/Output 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP

MCP6295 2 10 MHz 1100 3 1 8.7(2) 2.4 to 6.0 -40 to +125 Rail-to-Rail Input/Output, Dual connected,

Chip select 8-pin PDIP, 8-pin SOIC, 8-pin MSOP

MCP6L91 1 10 MHz 850 4 1 9.4(2) 2.4 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC(S), 8-pin MSOP(S), 5-pin SOT-23(S,R)

MCP6L92 2 10 MHz 850 4 1 9.4(2) 2.4 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin MSOP

MCP6L94 4 10 MHz 850 4 1 9.4(2) 2.4 to 6.0 -40 to +125 Rail-to-Rail Input/Output 14-pin SOIC, 14-pin TSSOP

MCP621 1 20 MHz 2500 0.2 5 13(3) 2.5 to 5.5 -40 to +125 Rail-to-Rail Output, Chip select,

mCal Technology 8-pin SOIC

MCP621S 1 20 MHz 2500 0.2 5 13(3) 2.5 to 5.5 -40 to +125 Rail-to-Rail Output, mCal Technology 5-pin SOT-23(S)

MCP622 2 20 MHz 2500 0.2 5 13(3) 2.5 to 5.5 -40 to +125 Rail-to-Rail Output, mCal Technology 8-pin SOIC, 8-pin 3x3 DFN

MCP623 1 20 MHz 2500 0.2 5 13(3) 2.5 to 5.5 -40 to +125 Rail-to-Rail Output, Chip select,

mCal Technology 6-pin SOT-23(S)

MCP624 4 20 MHz 2500 0.2 5 13(3) 2.5 to 5.5 -40 to +125 Rail-to-Rail Output, mCal Technology 14-pin SOIC, 14-pin TSSOP

MCP625 2 20 MHz 2500 0.2 5 13(3) 2.5 to 5.5 -40 to +125 Rail-to-Rail Output, Chip selects,

mCal Technology 10-pin MSOP, 10-pin 3x3 DFN

MCP629 4 20 MHz 2500 0.2 5 13(3) 2.5 to 5.5 -40 to +125 Rail-to-Rail Output,Chip selects,

mCal Technology 16-pin 4x4 QFN

MCP631 1 24 MHz 2500 8 4 10(3) 2.5 to 5.5 -40 to +125 Rail-to-Rail Output 8-pin SOIC

MCP632 2 24 MHz 2500 8 4 10(3) 2.5 to 5.5 -40 to +125 Rail-to-Rail Output 8-pin SOIC, 8-pin 3x3 DFN

MCP633 1 24 MHz 2500 8 4 10(3) 2.5 to 5.5 -40 to +125 Rail-to-Rail Output, Chip select 8-pin SOIC

MCP635 2 24 MHz 2500 8 4 10(3) 2.5 to 5.5 -40 to +125 Rail-to-Rail Output, Chip selects 10-pin MSOP, 10-pin 3x3 DFN

MCP651 1 50 MHz 6000 0.2 6 7.5(3) 2.5 to 5.5 -40 to +125 Rail-to-Rail Output, Chip select,

mCal Technology 8-pin SOIC

MCP651S 1 50 MHz 6000 0.2 6 7.5(3) 2.5 to 5.5 -40 to +125 Rail-to-Rail Output, mCal Technology 5-pin SOT-23(S)

MCP652 2 50 MHz 6000 0.2 6 7.5(3) 2.5 to 5.5 -40 to +125 Rail-to-Rail Output, mCal Technology 8-pin SOIC, 8-pin 3x3 DFN

MCP653 1 50 MHz 6000 0.2 6 7.5(3) 2.5 to 5.5 -40 to +125 Rail-to-Rail Output, Chip select,

mCal Technology 6-pin SOT-23(S)

MCP654 4 50 MHz 6000 0.2 6 7.5(3) 2.5 to 5.5 -40 to +125 Rail-to-Rail Output, mCal Technology 14-pin SOIC, 14-pin TSSOP

MCP655 2 50 MHz 6000 0.2 6 7.5(3) 2.5 to 5.5 -40 to +125 Rail-to-Rail Output, Chip selects,

mCal Technology 10-pin MSOP, 10-pin 3x3 DFN

MCP659 4 50 MHz 6000 0.2 6 7.5

(3)

2.5 to 5.5 -40 to +125 Rail-to-Rail Output,Chip selects,

mCal Technology 16-pin 4x4 QFN

MCP661 1 60 MHz 6000 8 6 6.8

(3)

2.5 to 5.5 -40 to +125 Rail-to-Rail Output 8-pin SOIC

MCP662 2 60 MHz 6000 8 6 6.8

(3)

2.5 to 5.5 -40 to +125 Rail-to-Rail Output 8-pin SOIC, 8-pin 3x3 DFN

MCP663 1 60 MHz 6000 8 6 6.8

(3)

2.5 to 5.5 -40 to +125 Rail-to-Rail Output, Chip select 8-pin SOIC

MCP665 2 60 MHz 6000 8 6 6.8

(3)

2.5 to 5.5 -40 to +125 Rail-to-Rail Output, Chip selects 10-pin MSOP, 10-pin 3x3 DFN

Legend: S = Standard Pinout; R = Reverse Pinout; U = Alternative Pinout

Note 1: Values are typical at 1 kHz

2: Values are typical at 10 kHz

3: Values are typical at 1 MHz

Analog and Interface Product Selector Guide 18

LINEAR – High Precision Operational Ampliﬁ ers

Part # # per

Package GBWP IQ Max

(mA) Vos Max

(μV) Vos Drift Max

(μV/°C) Operating

Voltage (V) Temperature

Range (°C) Features Packages

Chopper Stabilized

TC7650 1 2.0 MHz 3.5 5 0.05 4.5 to 16 0 to +70 Single and Split Supply 8-pin PDIP, 14-pin PDIP

TC7652 1 0.4 MHz 3 5 0.05 5 to 16 0 to +70 Single and Split Supply, Low Noise 8-pin PDIP, 14-pin PDIP

Auto-Zero

MCP6V01 1 1.3 MHz 0.4 2 0.05 1.8 to 5.5 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin 2x3 TDFN

MCP6V02 2 1.3 MHz 0.4 2 0.05 1.8 to 5.5 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin 4x4 DFN

MCP6V03 1 1.3 MHz 0.4 2 0.05 1.8 to 5.5 -40 to +125 Rail-to-Rail Input/Output, Chip select 8-pin SOIC, 8-pin 2x3 TDFN

MCP6V06 1 1.3 MHz 0.4 3 0.05 1.8 to 5.5 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin 2x3 TDFN

MCP6V07 2 1.3 MHz 0.4 3 0.05 1.8 to 5.5 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin 4x4 DFN

MCP6V08 1 1.3 MHz 0.4 3 0.05 1.8 to 5.5 -40 to +125 Rail-to-Rail Input/Output, Chip select 8-pin SOIC, 8-pin 2x3 TDFN

MCP6V26 1 2 MHz 0.8 2 0.05 2.3 to 5.5 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin MSOP, 8-pin 2x3 TDFN

MCP6V27 2 2 MHz 0.8 2 0.05 2.3 to 5.5 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin MSOP, 8-pin 4x4 DFN

MCP6V28 1 2 MHz 0.8 2 0.05 2.3 to 5.5 -40 to +125 Rail-to-Rail Input/Output, Chip select 8-pin SOIC, 8-pin MSOP, 8-pin 2x3 TDFN

TC913A/B 2 1.5 MHz 1.1 15 0.15/0.30 7 to 16 0 to +70 Single and Split Supply 8-pin PDIP, 8-pin SOIC

LINEAR – Programmable Gain Ampliﬁ ers (PGA)

Part # Channels -3dB BW

(MHz) IQ Typ.

(mA) Vos (μV) Operating

Voltage (V) Temperature

Range (°C) Features Packages

MCP6S21 1 2 to 12 1.1 275 2.5 to 5.5 -40 to +85 SPI, 8 Gain steps, Software shutdown 8-pin PDIP, 8-pin SOIC, 8-pin MSOP

MCP6S22 2 2 to 12 1.1 275 2.5 to 5.5 -40 to +85 SPI, 8 Gain steps, Software shutdown 8-pin PDIP, 8-pin SOIC, 8-pin MSOP

MCP6S26 6 2 to 12 1.1 275 2.5 to 5.5 -40 to +85 SPI, 8 Gain steps, Software shutdown 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP

MCP6S28 8 2 to 12 1.1 275 2.5 to 5.5 -40 to +85 SPI, 8 Gain steps, Software shutdown 16-pin PDIP, 16-pin SOIC

MCP6S91 1 1 to 18 1.0 4000 2.5 to 5.5 -40 to +125 SPI, 8 Gain steps, Software shutdown, VREF 8-pin PDIP, 8-pin SOIC, 8-pin MSOP

MCP6S92 2 1 to 18 1.0 4000 2.5 to 5.5 -40 to +125 SPI, 8 Gain steps, Software shutdown 8-pin PDIP, 8-pin SOIC, 8-pin MSOP

MCP6S93 2 1 to 18 1.0 4000 2.5 to 5.5 -40 to +125 SPI, 8 Gain steps, Software shutdown, VREF, SO 10-pin MSOP

LINEAR – Selectable Gain Ampliﬁ ers (SGA)

Part # Channels -3dB BW

(kHz) IQ (μA) VOS (mV) Operating

Voltage (V) Temperature

Range (°C) Gain Steps

(V/V) Features Packages

MCP6G01 1 900 110 4.5 1.8 to 5.5 -40 to +125 1, 10, 50 Tri-State control pin 8-pin SOIC, 8-pin MSOP, 5-pin SOT-23

(S,R,U)

MCP6G02 2 900 110 4.5 1.8 to 5.5 -40 to +125 1, 10, 50 Tri-State control pin 8-pin SOIC, 8-pin MSOP

MCP6G03 1 900 110 4.5 1.8 to 5.5 -40 to +125 1, 10, 50 Tri-State control pin,

Chip select 8-pin SOIC, 8-pin MSOP

MCP6G04 4 900 110 4.5 1.8 to 5.5 -40 to +125 1, 10, 50 Tri-State control pin 14-pin SOIC, 14-pin TSSOP

Analog and Interface Product Selector Guide 19

MIXED SIGNAL

MIXED SIGNAL – Successive Approximation Register (SAR) A/D Converters

Part # Resolution

(bits) Maximum

Sampling Rate

(ksamples/sec) # of Input

Channels Input Type Interface Input Voltage

Range (V) Max. Supply

Current (μA) Max. INL Temperature

Range (°C) Packages

MCP3021 10 22 1 Single-ended I2C™ 2.7 to 5.5 250 ±1 LSB -40 to +125 5-pin SOT-23A

MCP3001 10 200 1 Single-ended SPI 2.7 to 5.5 500 ±1 LSB -40 to +85 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin TSSOP

MCP3002 10 200 2 Single-ended SPI 2.7 to 5.5 650 ±1 LSB -40 to +85 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin TSSOP

MCP3004 10 200 4 Single-ended SPI 2.7 to 5.5 550 ±1 LSB -40 to +85 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP

MCP3008 10 200 8 Single-ended SPI 2.7 to 5.5 550 ±1 LSB -40 to +85 16-pin PDIP, 16-pin SOIC

MCP3221 12 22 1 Single-ended I2C™ 2.7 to 5.5 250 ±2 LSB -40 to +125 5-pin SOT-23A

MCP3201 12 100 1 Single-ended SPI 2.7 to 5.5 400 ±1 LSB -40 to +85 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin TSSOP

MCP3202 12 100 2 Single-ended SPI 2.7 to 5.5 550 ±1 LSB -40 to +85 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin TSSOP

MCP3204 12 100 4 Single-ended SPI 2.7 to 5.5 400 ±1 LSB -40 to +85 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP

MCP3208 12 100 8 Single-ended SPI 2.7 to 5.5 400 ±1 LSB -40 to +85 16-pin PDIP, 16-pin SOIC

MCP3301 13 100 1 Differential SPI 2.7 to 5.5 450 ±1 LSB -40 to +85 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin TSSOP

MCP3302 13 100 2 Differential SPI 2.7 to 5.5 450 ±1 LSB -40 to +85 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP

MCP3304 13 100 4 Differential SPI 2.7 to 5.5 450 ±1 LSB -40 to +85 16-pin PDIP, 16-pin SOIC

LINEAR – Comparators

Part # # per

Package VREF

(V) Typical Propagation

Delay (μs) IQ Typical

(μA) Vos Max

(mV) Operating

Voltage (V) Temperature

Range (°C) Features Packages

MCP6541 1 – 4 1 5 1.6 to 5.5 -40 to +125 Push-Pull, Rail-to-Rail Input/Output 5-pin SOT-23(S,R,U), 5-pin SC-70(S,U),

8-pin PDIP, 8-pin SOIC, 8-pin MSOP

MCP6542 2 – 4 1 5 1.6 to 5.5 -40 to +125 Push-Pull, Rail-to-Rail Input/Output 8-pin PDIP, 8-pin SOIC, 8-pin MSOP

MCP6543 1 – 4 1 5 1.6 to 5.5 -40 to +125 Push-Pull, Rail-to-Rail Input/Output, Chip select 8-pin PDIP, 8-pin SOIC, 8-pin MSOP

MCP6544 4 – 4 1 5 1.6 to 5.5 -40 to +125 Push-Pull, Rail-to-Rail Input/Output 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP

MCP6546 1 – 4 1 5 1.6 to 5.5 -40 to +125 Open-drain, 9V, Rail-to-Rail Input/Output 5-pin SOT-23(S,R,U), 5-pin SC-70(S,U),

8-pin PDIP, 8-pin SOIC, 8-pin MSOP

MCP6547 2 – 4 1 5 1.6 to 5.5 -40 to +125 Open-drain, 9V, Rail-to-Rail Input/Output 8-pin PDIP, 8-pin SOIC, 8-pin MSOP

MCP6548 1 – 4 1 5 1.6 to 5.5 -40 to +125 Open-drain, 9V, Rail-to-Rail Input/Output, Chip select 8-pin PDIP, 8-pin SOIC, 8-pin MSOP

MCP6549 4 – 4 1 5 1.6 to 5.5 -40 to +125 Open-drain, 9V, Rail-to-Rail Input/Output 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP

MCP65R41 1 1.21/2.4 4 2.5 10 1.8 to 5.5 -40 to +125 Push-Pull, Rail-to-Rail Input/Output, VREF 6-pin SOT-23

MCP65R46 1 1.21/2.4 4 2.5 10 1.8 to 5.5 -40 to +125 Open Drain, Rail-to-Rail Input/Output, VREF 6-pin SOT-23

MCP6561 1 – 0.047 100 10 1.8 to 5.5 -40 to +125 Push-Pull, Rail-to-Rail Input/Output 5-pin SOT-23(S,R,U), 5-pin SC-70(S)

MCP6562 2 – 0.047 100 10 1.8 to 5.5 -40 to +125 Push-Pull, Rail-to-Rail Input/Output 8-pin SOIC, 8-pin MSOP

MCP6564 4 – 0.047 100 10 1.8 to 5.5 -40 to +125 Push-Pull, Rail-to-Rail Input/Output 14-pin SOIC, 14-pin TSSOP

MCP6566 1 – 0.047 100 10 1.8 to 5.5 -40 to +125 Open-Drain, Rail-to-Rail Input/Output 5-pin SOT-23(S,R,U), 5-pin SC-70(S)

MCP6567 2 – 0.047 100 10 1.8 to 5.5 -40 to +125 Open-Drain, Rail-to-Rail Input/Output 8-pin SOIC, 8-pin MSOP

MCP6569 4 – 0.047 100 10 1.8 to 5.5 -40 to +125 Open-Drain, Rail-to-Rail Input/Output 14-pin SOIC, 14-pin TSSOP

Legend: S = Standard Pinout; R = Reverse Pinout; U = Alternative Pinout

Analog and Interface Product Selector Guide 20

MIXED SIGNAL – Dual Slope A/D Converters

Part # Supply

Voltage (V) Input Voltage Range Resolution Sampling

Rate (Conv/s) Input

Channels Data

Interface Temperature

Range (°C) Features Packages

TC500 ±4.5 to ±7.5 VSS + 1.5V to VDD – 1.5V Up to 16 bits 4 to 10 1 3-Wire 0 to +70 Differential input range, Programmable resolution/

conversion time 16-pin PDIP, 16-pin SOIC, 16-pin CerDIP

TC500A ±4.5 to ±7.5 VSS + 1.5V to VDD – 1.5V Up to 17 bits 4 to 10 1 3-Wire 0 to +70 Differential input range, Programmable resolution/

conversion time 16-pin PDIP, 16-pin SOIC, 16-pin CerDIP

TC510 +4.5 to +5.5 VSS + 1.5V to VDD – 1.5V Up to 17 bits 4 to 10 1 3-Wire 0 to +70 Differential input range, Programmable resolution/

conversion time, Charge pump (-V) output pin 24-pin PDIP, 24-pin SOIC

TC514 +4.5 to +5.5 VSS + 1.5V to VDD – 1.5V Up to 17 bits 4 to 10 4 3-Wire 0 to +70 Differential input range, Programmable resolution/

conversion time, Charge pump (-V) output pin 28-pin PDIP, 28-pin SOIC

TC520A +4.5 to +5.5 – – – – Serial port 0 to +70 Optional serial interface adapter for

TC500/500A/510/514 14-pin PDIP, 16-pin SOIC

TC7109 ±4.5 to ±5.5 VSS + 1.5V to VDD – 1.0V 12 bits plus

sign bit 2 to 10 1 Parallel or

Serial port -25 to +85 Differential input range 40-pin PDIP, 44-pin PLCC, 44-pin MQFP

TC7109A ±4.5 to ±5.5 VSS + 1.5V to VDD – 1.0V 12 bits plus

sign bit 2 to 10 1 Parallel or

Serial port -25 to +85 Differential input range 40-pin PDIP, 44-pin PLCC, 44-pin MQFP

MIXED SIGNAL – Energy Measurement ICs

Part # Dynamic

Range Typical

Accuracy ADC

Channels Gain

Selection Output Type Typical Voltage

Reference Drift

(ppm/°C)

Typical

Supply

Current (mA)

Analog

Voltage

Range (V)

Digital

Voltage

Range (V) Temperature

Range (°C) Features Packages

MCP3901 24-bit resolution 91 dB SINAD 2 up to 32 SPI 12 2.6 4.5 to 5.5 2.7 to 5.5 -40 to +125 Phase correction,

Programmable data rate 20-pin SSOP,

20-pin 4x4 QFN

MCP3903 24-bit resolution 91 dB SINAD 6 up to 32 SPI 5 8.3 4.5 to 5.5 2.7 to 3.6 -40 to +125 Phase correction,

Programmable data rate 28-pin SSOP

MCP3905A 500:1 0.1% 2 up to 16 Active power pulse 15 3.9 4.5 to 5.5 4.5 to 5.5 -40 to +125 Active power calculation 24-pin SSOP

MCP3905L 500:1 0.1% 2 up to 16 Active power pulse 15 3.9 4.5 to 5.5 4.5 to 5.5 -40 to +125 Active power calculation,

Reduced pulse-width 24-pin SSOP

MCP3906A 1000:1 0.1% 2 up to 32 Active power pulse 15 3.9 4.5 to 5.5 4.5 to 5.5 -40 to +125 Active power calculation 24-pin SSOP

MCP3909 1000:1 0.1% 2 up to 16 Active power pulse/

SPI 15 3.9 4.5 to 5.5 4.5 to 5.5 -40 to +125 Active power calculation 24-pin SSOP

MIXED SIGNAL – Delta-Sigma A/D Converters

Part # Resolution

(bits) Maximum

Sampling Rate

(samples/sec) # of Input

Channels Interface Supply Voltage

Range (V) Typical

Supply

Current (μA) Typical INL

(ppm) Temperature

Range (°C) Features Packages

MCP3421 18 to 12 4 to 240 1 Diff I2C™ 2.7 to 5.5 155 10 -40 to +125 PGA, VREF 6-pin SOT-23A

MCP3422 18 to 12 4 to 240 2 Diff I2C™ 2.7 to 5.5 145 10 -40 to +125 PGA, VREF 8-pin SOIC, 8-pin MSOP, 8-pin 2x3 DFN

MCP3423 18 to 12 4 to 240 2 Diff I2C™ 2.7 to 5.5 145 10 -40 to +125 PGA, VREF, Selectable I2C™ addressing 10-pin MSOP, 10-pin 3x3 DFN

MCP3424 18 to 12 4 to 240 4 Diff I2C™ 2.7 to 5.5 145 10 -40 to +125 PGA, VREF, Selectable I2C™ addressing 14-pin SOIC, 14-pin TSSOP

MCP3425 16 to 12 15 to 240 1 Diff I2C™ 2.7 to 5.5 155 10 -40 to +125 PGA, VREF 6-pin SOT-23A

MCP3426 16 to 12 15 to 240 2 Diff I2C™ 2.7 to 5.5 145 10 -40 to +125 PGA, VREF 8-pin SOIC, 8-pin MSOP, 8-pin 2x3 DFN

MCP3427 16 to 12 15 to 240 2 Diff I2C™ 2.7 to 5.5 145 10 -40 to +125 PGA, VREF, Selectable I2C™ addressing 10-pin MSOP, 10-pin 3x3 DFN

MCP3428 16 to 12 15 to 240 4 Diff I2C™ 2.7 to 5.5 145 10 -40 to +125 PGA, VREF, Selectable I2C™ addressing 14-pin SOIC, 14-pin TSSOP

MCP3550-50 22 13 1 Diff SPI 2.7 to 5.5 120 2 -40 to +125 50 Hz rejection 8-pin SOIC, 8-pin MSOP

MCP3550-60 22 15 1 Diff SPI 2.7 to 5.5 140 2 -40 to +125 60 Hz rejection 8-pin SOIC, 8-pin MSOP

MCP3551 22 14 1 Diff SPI 2.7 to 5.5 120 2 -40 to +125 Simultaneous 50/60 Hz rejection 8-pin SOIC, 8-pin MSOP

MCP3553 20 60 1 Diff SPI 2.7 to 5.5 140 2 -40 to +125 8-pin SOIC, 8-pin MSOP

Analog and Interface Product Selector Guide 21

MIXED SIGNAL – Display A/D Converters

Part # Display

Type Supply

Voltage (V) Resolution

(Digits) Resolution

(Counts) Power

(mW) Temperature Range

(°C) Features Packages

TC7106 LCD 9 3½ ±2,000 10 -25 to +85 For DMM, DPM, Data logger applications 40-pin PDIP, 44-pin PLCC, 44-pin MQFP

TC7106A LCD 9 3½ ±2,000 10 -25 to +85 For DMM, DPM, Data logger applications 40-pin PDIP, 44-pin PLCC, 44-pin MQFP

TC7107 LED ±5 3½ ±2,000 10 -25 to +85 For DMM, DPM, Data logger applications 40-pin PDIP, 44-pin PLCC, 44-pin MQFP

TC7107A LED ±5 3½ ±2,000 10 -25 to +85 For DMM, DPM, Data logger applications 40-pin PDIP, 44-pin PLCC, 44-pin MQFP

TC7116 LCD 9 3½ ±2,000 10 -25 to +85 Hold function 40-pin PDIP, 44-pin PLCC, 44-pin MQFP

TC7116A LCD 9 3½ ±2,000 10 -25 to +85 Hold function 40-pin PDIP, 44-pin PLCC, 44-pin MQFP

TC7117 LED ±5 3½ ±2,000 10 -25 to +85 Hold function 40-pin PDIP, 44-pin PLCC, 44-pin MQFP

TC7117A LED ±5 3½ ±2,000 10 -25 to +85 Hold function 40-pin PDIP, 44-pin PLCC, 44-pin MQFP

TC7126 LCD 9 3½ ±2,000 0.5 -25 to +85 Low-power TC7106 40-pin PDIP, 44-pin PLCC, 44-pin MQFP

TC7126A LCD 9 3½ ±2,000 0.5 -25 to +85 Low-power TC7106 40-pin PDIP, 44-pin PLCC, 44-pin MQFP

TC7129 LCD 9 4½ ±20,000 4.5 0 to +70 Lowest noise ±3 mV sensitivity 40-pin PDIP, 44-pin PLCC, 44-pin MQFP

MIXED SIGNAL – Digital Potentiometers

Part # Number

of Taps Memory Number per

Package Interface Resistance

(kOhms) INL

(max) DNL

(max) Temperature

Range (°C) Comments Packages

MCP4011 64 Volatile 1 Up/Down 2.1, 5, 10, 50 0.5 0.5 -40 to +125 Potentiometer mode 8-pin SOIC, 8-pin MSOP, 8-pin 2x3 DFN

MCP4012 64 Volatile 1 Up/Down 2.1, 5, 10, 50 0.5 0.5 -40 to +125 Rheostat mode 6-pin SOT-23

MCP4013 64 Volatile 1 Up/Down 2.1, 5, 10, 50 0.5 0.5 -40 to +125 Potentiometer to VSS 6-pin SOT-23

MCP4014 64 Volatile 1 Up/Down 2.1, 5, 10, 50 0.5 0.5 -40 to +125 Rheostat to VSS 5-pin SOT-23

MCP4017 128 Volatile 1 I2C™ 5, 10, 50, 100 0.5 0.25 -40 to +125 7-bit, Volatile, I2C digital potentiometer 6-pin SC-70

MCP4018 128 Volatile 1 I2C™ 5, 10, 50, 100 0.5 0.25 -40 to +125 7-bit, Volatile, I2C digital potentiometer 6-pin SC-70

MCP4019 128 Volatile 1 I2C™ 5, 10, 50, 100 0.5 0.25 -40 to +125 7-bit, Volatile, I2C digital potentiometer 5-pin SC-70

MCP40D17 128 Volatile 1 I2C™ 5, 10, 50, 100 0.5 0.25 -40 to +125 7-bit, Volatile, I2C digital potentiometer 6-pin SC-70

MCP40D18 128 Volatile 1 I2C™ 5, 10, 50, 100 0.5 0.25 -40 to +125 7-bit, Volatile, I2C digital potentiometer 6-pin SC-70

MCP40D19 128 Volatile 1 I2C™ 5, 10, 50, 100 0.5 0.25 -40 to +125 7-bit, Volatile, I2C digital potentiometer 5-pin SC-70

MCP4021 64 Nonvolatile 1 Up/Down 2.1, 5, 10, 50 0.5 0.5 -40 to +125 Potentiometer mode, Shutdown, WiperLock™ Technology 8-pin SOIC, 8-pin MSOP, 8-pin 2x3 DFN

MCP4022 64 Nonvolatile 1 Up/Down 2.1, 5, 10, 50 0.5 0.5 -40 to +125 Rheostat mode, Shutdown, WiperLock™ Technology 6-pin SOT-23

MCP4023 64 Nonvolatile 1 Up/Down 2.1, 5, 10, 50 0.5 0.5 -40 to +125 Potentiometer to VSS, WiperLock™ Technology 6-pin SOT-23

MCP4024 64 Nonvolatile 1 Up/Down 2.1, 5, 10, 50 0.5 0.5 -40 to +125 Rheostat to VSS, Shutdown, WiperLock™ Technology 5-pin SOT-23

MCP4141 128 Nonvolatile 1 SPI 5, 10, 50, 100 0.5 0.25 -40 to +125 Potentiometer mode, Shutdown 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin 3x3 DFN

MCP4142 128 Nonvolatile 1 SPI 5, 10, 50, 100 0.8 0.25 -40 to +125 Rheostat mode, Shutdown 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin 3x3 DFN

MCP4241 128 Nonvolatile 2 SPI 5, 10, 50, 100 0.5 0.25 -40 to +125 Potentiometer mode, Shutdown, WiperLock™ Technology 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP, 16-pin 4x4 QFN

MCP4242 128 Nonvolatile 2 SPI 5, 10, 50, 100 0.8 0.25 -40 to +125 Rheostat mode, Shutdown 10-pin MSOP, 10-pin 3x3 DFN

MIXED SIGNAL – Binary and BCD A/D Converters

Part # Description Supply

Voltage (V) Input Voltage Range Resolution

(Digits) Resolution

(Counts) Max Power

(mW) Data

Interface Temperature

Range (°C) Features Packages

TC850 Binary A/D ±5 VSS + 1.5V to VDD – 1.5V 15-bit ±32,768 35 8-bit parallel -25 to +70 Highest conversion speed (40 conv/sec) 44-pin PLCC, 40-pin PDIP

TC14433 BCD A/D ±4.5 to ±8 ±199.9 mV to 1.999V 3½ ±2,000 20 MUXed BCD -40 to +85 For DMM, DPM, Data loggers 24-pin SOIC, 24-pin PDIP,

28-pin PLCC

TC14433A BCD A/D ±4.5 to ±8 ±199.9 mV to 1.999V 3½ ±2,000 20 MUXed BCD -40 to +85 For DMM, DPM, Data loggers 24-pin PDIP, 28-pin PLCC

Analog and Interface Product Selector Guide 22

MIXED SIGNAL – Digital Potentiometers (Continued)

Part # Number

of Taps Memory Number per

Package Interface Resistance

(kOhms) INL

(max) DNL

(max) Temperature

Range (°C) Comments Packages

MCP4131 128 Volatile 1 SPI 5, 10, 50, 100 0.5 0.25 -40 to +125 Potentiometer mode, Shutdown 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin 3x3 DFN

MCP4132 128 Volatile 1 SPI 5, 10, 50, 100 0.8 0.25 -40 to +125 Rheostat mode, Shutdown 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin 3x3 DFN

MCP4231 128 Volatile 2 SPI 5, 10, 50, 100 0.5 0.25 -40 to +125 Potentiometer mode, Shutdown, WiperLock™ Technology 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP, 16-pin 4x4 QFN

MCP4232 128 Volatile 2 SPI 5, 10, 50, 100 0.8 0.25 -40 to +125 Rheostat mode, Shutdown 10-pin MSOP, 10-pin 3x3 DFN

MCP41010 256 Volatile 1 SPI 10 1 1 -40 to +85 Potentiometer mode, Shutdown 8-pin PDIP, 8-pin SOIC

MCP41050 256 Volatile 1 SPI 50 1 1 -40 to +85 Potentiometer mode, Shutdown 8-pin PDIP, 8-pin SOIC

MCP41100 256 Volatile 1 SPI 100 1 1 -40 to +85 Potentiometer mode, Shutdown 8-pin PDIP, 8-pin SOIC

MCP4151 256 Volatile 1 SPI 5, 10, 50, 100 1 0.5 -40 to +125 Potentiometer mode, Shutdown 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin 3x3 DFN

MCP4152 256 Volatile 1 SPI 5, 10, 50, 100 1 0.5 -40 to +125 Rheostat mode, Shutdown 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin 3x3 DFN

MCP4161 256 Nonvolatile 1 SPI 5, 10, 50, 100 1 0.5 -40 to +125 Potentiometer mode, Shutdown 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin 3x3 DFN

MCP4162 256 Nonvolatile 1 SPI 5, 10, 50, 100 1 0.5 -40 to +125 Rheostat mode, Shutdown 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin 3x3 DFN

MCP42010 256 Volatile 2 SPI 10 1 1 -40 to +85 Potentiometer mode, Shutdown 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP

MCP42100 256 Volatile 2 SPI 100 1 1 -40 to +85 Potentiometer mode, Shutdown 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP

MCP4251 256 Volatile 2 SPI 5, 10, 50, 100 1 0.5 -40 to +125 Potentiometer mode, Shutdown, WiperLock™ Technology 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP, 16-pin 4x4 QFN

MCP4252 256 Volatile 2 SPI 5, 10, 50, 100 1 0.5 -40 to +125 Rheostat mode, Shutdown 10-pin MSOP, 10-pin 3x3 DFN

MCP4261 256 Nonvolatile 2 SPI 5, 10, 50, 100 1 0.5 -40 to +125 Potentiometer mode, Shutdown, WiperLock™ Technology 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP, 16-pin 4x4 QFN

MCP4262 256 Nonvolatile 2 SPI 5, 10, 50, 100 1 0.5 -40 to +125 Rheostat mode, Shutdown 10-pin MSOP, 10-pin 3x3 DFN

MCP4341 129 Nonvolatile 4 I2C™ 5, 10, 50, 100 0.8 0.375 -40 to +125 7-bit, Volatile potentiometer with an I2C interface 20-pin TSSOP, 20-pin 4x4 QFN

MCP4342 129 Nonvolatile 4 I2C™ 5, 10, 50, 100 0.8 0.375 -40 to +125 7-bit, Volatile rheostat with an I2C interface 14-pin TSSOP

MCP4361 257 Nonvolatile 4 I2C™ 5, 10, 50, 100 1 0.5 -40 to +125 8-bit, Non-volatile potentiometer with an I2C interface 20-pin TSSOP, 20-pin 4x4 QFN

MCP4362 257 Nonvolatile 4 I2C™ 5, 10, 50, 100 1 0.5 -40 to +125 8-bit, Non-volatile rheostat with an I2C interface 14-pin TSSOP

MCP4331 129 Volatile 4 I2C™ 5, 10, 50, 100 0.8 0.375 -40 to +125 7-bit, Volatile potentiometer with an I2C interface 20-pin TSSOP, 20-pin 4x4 QFN

MCP4332 129 Volatile 4 I2C™ 5, 10, 50, 100 0.8 0.375 -40 to +125 7-bit, Volatile rheostat with an I2C interface 14-pin TSSOP

MCP4351 257 Volatile 4 I2C™ 5, 10, 50, 100 1 0.5 -40 to +125 8-bit, Non-volatile potentiometer with an I2C interface 20-pin TSSOP, 20-pin 4x4 QFN

MCP4352 257 Volatile 4 I2C™ 5, 10, 50, 100 1 0.5 -40 to +125 8-bit, Non-volatile rheostat with an I2C interface 14-pin TSSOP

MCP4441 129 Nonvolatile 4 I2C™ 5, 10, 50, 100 0.5 0.25 -40 to +125 Potentiometer mode, WiperLock™ Technology 20-pin TSSOP, 20-pin 4x4 QFN

MCP4442 129 Nonvolatile 4 I2C™ 5, 10, 50, 101 0.8 0.375 -40 to +125 Rheostat mode, WiperLock™ Technology 14-pin TSSOP

MCP4461 257 Nonvolatile 4 I2C™ 5, 10, 50, 102 1 0.5 -40 to +125 Potentiometer mode, WiperLock™ Technology 20-pin TSSOP, 20-pin 4x4 QFN

MCP4462 257 Nonvolatile 4 I2C™ 5, 10, 50, 103 1 0.5 -40 to +125 Rheostat mode, WiperLock™ Technology 14-pin TSSOP

MCP4531 128 Volatile 1 I2C™ 5, 10, 50, 100 0.5 0.25 -40 to +125 Potentiometer mode 8-pin MSOP

MCP4631 128 Volatile 2 I2C™ 5, 10, 50, 100 0.5 0.25 -40 to +125 Potentiometer mode 14-pin TSSOP, 16-pin 4x4 QFN

MCP4541 128 Nonvolatile 1 I2C™ 5, 10, 50, 100 0.5 0.25 -40 to +125 Potentiometer mode, WiperLock™ Technology 8-pin MSOP

MCP4641 128 Nonvolatile 2 I2C™ 5, 10, 50, 100 0.5 0.25 -40 to +125 Potentiometer mode, WiperLock™ Technology 14-pin TSSOP, 16-pin 4x4 QFN

MCP4551 256 Volatile 1 I2C™ 5, 10, 50, 100 1 0.5 -40 to +125 Potentiometer mode 8-pin MSOP

MCP4651 256 Volatile 2 I2C™ 5, 10, 50, 100 1 0.5 -40 to +125 Potentiometer mode 14-pin TSSOP, 16-pin 4x4 QFN

MCP4561 256 Nonvolatile 1 I2C™ 5, 10, 50, 100 1 0.5 -40 to +125 Potentiometer mode, WiperLock™ Technology 8-pin MSOP

Analog and Interface Product Selector Guide 23

MIXED SIGNAL – Digital Potentiometers (Continued)

Part # Number

of Taps Memory Number per

Package Interface Resistance

(kOhms) INL

(max) DNL

(max) Temperature

Range (°C) Comments Packages

MCP4661 256 Nonvolatile 2 I2C™ 5, 10, 50, 100 1 0.5 -40 to +125 Potentiometer mode, WiperLock™ Technology 14-pin TSSOP, 16-pin 4x4 QFN

MCP4532 128 Nonvolatile 1 I2C™ 5, 10, 50, 100 0.8 0.375 -40 to +125 Rheostat mode 8-pin MSOP, 8-pin 3x3 DFN

MCP4632 128 Nonvolatile 2 I2C™ 5, 10, 50, 100 0.8 0.375 -40 to +125 Rheostat mode 10-pin MSOP, 10-pin 3x3 DFN

MCP4542 128 Nonvolatile 1 I2C™ 5, 10, 50, 100 0.8 0.375 -40 to +125 Rheostat mode, WiperLock™ Technology 8-pin MSOP, 8-pin 3x3 DFN

MCP4642 128 Nonvolatile 2 I2C™ 5, 10, 50, 100 0.8 0.375 -40 to +125 Rheostat mode, WiperLock™ Technology 10-pin MSOP, 10-pin 3x3 DFN

MCP4552 256 Nonvolatile 1 I2C™ 5, 10, 50, 100 1 0.5 -40 to +125 Rheostat mode 8-pin MSOP, 8-pin 3x3 DFN

MCP4652 256 Nonvolatile 2 I2C™ 5, 10, 50, 100 1 0.5 -40 to +125 Rheostat mode 10-pin MSOP, 10-pin 3x3 DFN

MCP4562 256 Nonvolatile 1 I2C™ 5, 10, 50, 100 1 0.5 -40 to +125 Rheostat mode, WiperLock™ Technology 8-pin MSOP, 8-pin 3x3 DFN

MCP4662 256 Nonvolatile 2 I2C™ 5, 10, 50, 100 1 0.5 -40 to +125 Rheostat mode, WiperLock™ Technology 10-pin MSOP, 10-pin 3x3 DFN

MIXED SIGNAL – D/A Converters

Part # Resolution

(Bits) DACs per

Package Interface VREF Output Settling

Time (μs) DNL

(LSB) Typical Standby Cur-

rent (μA) Typical Operating

Current (μA) Temperature Range

(°C) Packages

TC1320 8 1 SMbus Ext 10 ±0.8 0.1 350 -40 to +85 8-pin MSOP, 8-pin SOIC

TC1321 10 1 SMbus Ext 10 ±2 0.1 350 -40 to +85 8-pin MSOP, 8-pin SOIC

MCP4706 8 1 I2C™ Ext 6 0.05 0.06 210 -40 to +125 6-pin SOT-23

MCP4716 10 1 I2C™ Ext 6 0.188 0.06 210 -40 to +125 6-pin SOT-23

MCP4725 12 1 I2C™ VDD 6 0.75 1 210 -40 to +125 6-pin SOT-23

MCP4726 12 1 I2C™ Ext 6 0.75 0.06 210 -40 to +125 6-pin SOT-23

MCP4728 12 4 I2C™ Int/VDD 6 0.75 0.04 800 -40 to +125 10-pin MSOP

MCP4801 8 1 SPI Int 4.5 0.5 0.3 330 -40 to +125 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin DFN

MCP4802 8 2 SPI Int 4.5 0.5 3.3 415 -40 to +125 8-pin PDIP, 8-pin SOIC, 8-pin MSOP

MCP4811 10 1 SPI Int 4.5 0.5 0.3 330 -40 to +125 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin DFN

MCP4812 10 2 SPI Int 4.5 0.5 3.3 415 -40 to +125 8-pin PDIP, 8-pin SOIC, 8-pin MSOP

MCP4821 12 1 SPI Int 4.5 1 0.3 330 -40 to +125 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin DFN

MCP4822 12 2 SPI Int 4.5 1 3.3 415 -40 to +125 8-pin PDIP, 8-pin SOIC, 8-pin MSOP

MCP4901 8 1 SPI Ext 4.5 0.5 3.3 175 -40 to +125 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin DFN

MCP4902 8 2 SPI Ext 4.5 0.5 0.3 350 -40 to +125 14-pin PDIP, 14-pin SOIC, 14-pinTSSOP

MCP4911 10 1 SPI Ext 4.5 0.5 3.3 175 -40 to +125 8-pin DFN, 8-pin MSOP, 8-pin PDIP, 8-pin SOIC

MCP4912 10 2 SPI Ext 4.5 0.5 0.3 350 -40 to +125 14-pin PDIP, 14-pin SOIC, 14-pinTSSOP

MCP4921 12 1 SPI Ext 4.5 0.75 3.3 175 -40 to +125 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin DFN

MCP4922 12 2 SPI Ext 4.5 0.75 0.3 350 -40 to +125 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP

Note: The analog output is voltage.

MIXED SIGNAL –

Frequency-to-Voltage/Voltage-to-Frequency Converters

Part # Frequency Range (kHz) Full Scale (ppm FS/°C) Non-linearity (%FS) Temperature Range (°C) Packages

TC9400 100 ±40 ±0.05 -40 to +85 14-pin PDIP, 14-pin SOIC

TC9401 100 ±40 ±0.02 -40 to +85 14-pin PDIP, 14-pin SOIC

TC9402 100 ±100 ±0.25 -40 to +85 14-pin PDIP, 14-pin SOIC

Analog and Interface Product Selector Guide 24

INTERFACE

INTERFACE – Controller Area Network (CAN) Products

Part # Operating

Voltage (V) Temperature

Range (°C) Tx

Buffers Rx

Buffers Filters Masks Interrupt

Output Unique Features Packages

MCP2510

(1)

2.7 to 5.5 -40 to +125 3 2 6 2 Yes CAN 2.0B Active controller with SPI interface to MCU, 3 transmit

buffers, 2 receive buffers, HW and SW message triggers 18-pin PDIP, 18-pin SOIC, 20-pin TSSOP

MCP2515 2.7 to 5.5 -40 to +125 3 2 6 2 Yes MCP2510 pin compatible upgrade with enhanced features

including higher throughput and data byte ﬁ ltering 18-pin PDIP, 18-pin SOIC, 20-pin TSSOP

MCP25020 2.7 to 5.5 -40 to +125 3 2 2 1 N/A CAN 2.0B Active I/O Expander, Conﬁ gurable I/O, 2 PWM outputs 14-pin PDIP, 14-pin SOIC

MCP25025 2.7 to 5.5 -40 to +85 3 2 2 1 N/A CAN 2.0B Active I/O Expander, Conﬁ gurable I/O,

2 PWM outputs, One-wire CAN option 14-pin PDIP, 14-pin SOIC

MCP25050 2.7 to 5.5 -40 to +125 3 2 2 1 N/A Mixed-Signal CAN 2.0B Active I/O Expander, Conﬁ gurable I/O,

4 10-bit ADCs, 2 PWM outputs 14-pin PDIP, 14-pin SOIC

MCP25055 2.7 to 5.5 -40 to +85 3 2 2 1 N/A Mixed-Signal CAN 2.0B Active I/O Expander, Conﬁ gurable I/O,

4 10-bit ADCs, 2 PWM outputs, One-wire CAN option 14-pin PDIP, 14-pin SOIC

MCP2551 4.5 to 5.5 -40 to +125 n/a n/a n/a n/a N/A High-speed CAN Transceiver (1 Mbps max. CAN bus

speed), ISO11898 compatible, Industry standard pinout 8-pin PDIP, 8-pin SOIC

Note 1: Not recommended for new designs.

INTERFACE – Passive Access Products

Part # Operating

Voltage (V)

Operating

Temperature

Range (°C)

Bus

Type RF Carrier

Frequency Data Format Features Packages

MCP2030 1.8 to 3.6 -40 to +85 SPI 125 kHz NRZ Three axis signal conditioning devices for passive access

applications, High-sensitivity, Conﬁ gurable smart wake-up ﬁ lter 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP

INTERFACE – Infrared Products

Part # Operating

Voltage (V) Operating

Temperature Range (°C) Max. Baud Rate

(Kbaud) Unique Features Packages

MCP2120 2.5 to 5.5 -40 to +85 325 UART to IR encoder/decoder with both hardware and software baud rate selection 14-pin PDIP, 14-pin SOIC

MCP2122 1.8 to 5.5 -40 to +85 16x less than clock input UART to IR encoder/decoder 8-pin PDIP, 8-pin SOIC

MCP2140A 2.0 to 5.5 -40 to +85 9.6 IrDA

Standard protocol handler plus bit encoder/decoder, Fixed baud rate, Low-cost 18-pin PDIP, 18-pin SOIC, 20-pin SSOP

MCP2150 3.0 to 5.5 -40 to +85 115.2 IrDA

Standard protocol handler plus bit encoder/decoder on one chip for DTE

applications, Programmable ID 18-pin PDIP, 18-pin SOIC, 20-pin SSOP

MCP2155 3.0 to 5.5 -40 to +85 115.2 IrDA

Standard protocol handler plus bit encoder/decoder on one chip for DCE

applications, Programmable ID 18-pin PDIP, 18-pin SOIC, 20-pin SSOP

IrDA

is a registered trademark of Infrared Data Association

INTERFACE – Ethernet Products

Part # Operating

Voltage (V) Operating Temperature

Range (°C) MAC PHY TX/RX RAM Interface Features Packages

ENC28J60 3.1 to 3.6 -40 to +85 Yes 10Base-T 8 KB SPI - 10Base-T Ethernet controller, IEEE 802.3™ compliant

- Loopback test modes, Auto-polarity detection

- Clock out pin with programmable frequencies

28-pin SOIC, 28-pin SSOP,

28-pin 6x6 QFN, 28-pin SPDIP

ENC424J600 3.0 to 3.6 -40 to +85 Yes 10/100Base-T 24 KB - SPI

- 8-bit multiplexed

parallel interface

- 10/100 Ethernet controller, IEEE 802.3(TM) compliant

- Cryptographic Security Engines - MD5, SHA-1, AES, RSA

- Preprogrammed unique MAC address

- Loopback test modes, Auto-polarity detection

- Clock out pin with programmable frequencies

44-pin TQFP, 44-pin QFN

ENC624J600 3.0 to 3.6 -40 to +85 Yes 10/100Base-T 24 KB

- SPI

- 8-bit or 16-bit multiplexed

or demultiplexed parallel

interface

- 10/100 Ethernet controller, IEEE 802.3(TM) compliant

- Cryptographic Security Engines - MD5, SHA-1, AES, RSA

- Preprogrammed unique MAC address

- Loopback test modes, Auto-polarity detection

- Clock out pin with programmable frequencies

64-pin TQFP

Analog and Interface Product Selector Guide 25

INTERFACE – LIN Transceiver Products

Part # Description VREG Output

Voltage (V) Operating

Temperature

Range (°C) VREG Output

Current (mA) Vcc Range

(V) Max

Baud Rate LIN Speciﬁ cation

Supported Packages

MCP201 LIN Transceiver with integrated VREG 5.0 ±5% -40 to +125 50 6 to 18(1) 20 Kbaud Revision 1.2 8-pin PDIP, 8-pin SOIC, 8-pin 6x5 DFN

MCP2003 Stand-Alone LIN Transceiver (industry

standard pinout) None -40 to +125 None 6 to 27(1) 20 Kbaud Revision 1.3, 2.0, 2.1,

SAE J2602 8-pin PDIP, 8-pin SOIC, 8-pin 4x4 DFN

MCP2004 Stand-Alone LIN Transceiver with

TXE/Fault I/O None -40 to +125 None 6 to 27(1) 20 Kbaud Revision 1.3, 2.0, 2.1,

SAE J2602 8-pin PDIP, 8-pin SOIC, 8-pin4x4 DFN

MCP2021 LIN Transceiver with integrated VREG 5.0 ± 3%

3.3 ± 3% -40 to +125 50 6 to 18(1) 20 Kbaud Revision 1.3, 2.0, 2.1,

SAE J2602 8-pin PDIP, 8-pin SOIC, 8-pin 6x5 DFN, 8-pin

6x5 DFN

MCP2022 LIN Transceiver with integrated VREG,

RESET pin 5.0 ± 3%

3.3 ± 3% -40 to +125 50 6 to 18(1) 20 Kbaud Revision 1.3, 2.0, 2.1,

SAE J2602 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP

Note 1: Can withstand 40V load dump.

INTERFACE – Stand-alone RF Receiver Products

Part # Modulation Data Rate (kbps) Frequency

Range (MHz) Sensitivity (dBm) IF Frequency Range

(MHz) Operating Voltage (V) RSSI Selectable LNA Gain Packages

rfRXD0420 ASK, FSK, FM 80 300 to 450 -111 0.455 to 21.4 2.5 to 5.5 Yes Yes 32-pin LQFP

rfRXD0920 ASK, FSK, FM 80 800 to 930 -109 0.455 to 21.4 2.5 to 5.5 Yes Yes 32-pin LQFP

INTERFACE – IEEE 802.15.4 ZigBee® RF Transceiver Products

Part # Frequency

Range (GHz) Sensitivity

(dBm) Power

Output

(dBm) RSSI TX Power

Consumption

(mA)

RX Power

Consumption

(mA) Clock

(MHz) Sleep MAC MAC

Features Encryption Interface Pin

Count Packages

MRF24J40 2.405-2.48 -95 0 Yes 18 22 20 Yes Yes CSMA-CA AES128 4-wire SPI 40 40-pin QFN

MRF24J40MA 2.405-2.48 -95 0 Yes 23 19 20 Yes Yes CSMA-CA AES128 4-wire SPI 12 Module

MRF24J40MB 2.405-2.48 -102 20 Yes 120 25 20 Yes Yes CSMA-CA AES128 4-wire SPI 12 Module

MRF49XA 433/868/915 -110 7 Yes 15 11 – Yes – – – 4-wire SPI 16 16-pin TSSOP

INTERFACE – USB Products

Part # USB Speed USB Compliant PHY MCU Interface Tx/Rx Buffer Size (bytes) Number of GPIO Operating Voltage (V) Packages

MCP2200 Full-Speed USB (12 Mb/s),

Low-Speed USB (1.5 Mb/s) Yes Yes UART 128/128 8 2.7 to 5.5 20-pin SOIC, 20-pin TSSOP, 20-pin QFN

INTERFACE – Serial Peripherals

Part # Description Operating

Voltage (V) Operating

Temperature

Range (°C) Bus

Type Max. Bus

Frequency

(kHz) Features Packages

MCP23008 8-bit I/O Port Expander 1.8 to 5.5 -40 to +85 I2C™ 1700 3 HW address pins, HW interrupt, 25 mA source/sink capability per I/O 18-pin PDIP, 18-pin SOIC, 20-pin SSOP, 20-pin 4x4 QFN

MCP23S08 8-bit I/O Port Expander 1.8 to 5.5 -40 to +85 SPI 10000 2 HW address pins, HW interrupt, 25 mA source/sink capability per I/O 18-pin PDIP, 18-pin SOIC, 20-pin SSOP, 20-pin 4x4 QFN

MCP23009 8-bit I/O Port Expander 1.8 to 5.5 -40 to +125 I2C™ 3400 1 HW address pin, HW interrupt, 25 mA source/sink per I/O, 100 kHz, 400 kHz

and 3.4 MHz I2C™ supported 18-pin PDIP, 18-pin SOIC, 20-pin SSOP

MCP23S09 8-bit I/O Port Expander 1.8 to 5.5 -40 to +125 SPI 10000 HW interrupt, 25 mA source/sink per I/O 18-pin PDIP, 18-pin SOIC

MCP23016 16-bit I/O Port Expander 2.0 to 5.5 -40 to +85 I2C™ 400 3 HW address inputs, HW interrupt, 25 mA source/sink capability per I/O 28-pin PDIP, 28-pin SOIC, 28-pin SSOP, 28-pin 6x6 QFN

MCP23017 16-bit I/O Expander 1.8 to 5.5 -40 to +125 I2C™ 1700 3 HW address pins, 25 mA sink/source per I/O, 100 kHz, 400 kHz and 3-4

MHz I2C™ supported, Interrupt output 28-pin PDIP, 28-pin SOIC, 28-pin SSOP, 28-pin QFN

MCP23S17 16-bit I/O Expander 1.8 to 5.5 -40 to +125 SPI 10000 3 HW address pins, 25 mA sink/source per I/O, Interrupt output 28-pin PDIP, 28-pin SOIC, 28-pin SSOP, 28-pin QFN

MCP23018 16-bit I/O Port Expander 1.8 to 5.5 -40 to +125 I2C™ 3400 1 HW address pin, 2 HW interrupts, 25 mA source/sink per I/O, 100 kHz, 400

kHz and 3.4 MHz I2C™ supported 24-pin SSOP, 28-pin SOIC, 28-pin SDIP

MCP23S18 16-bit I/O Port Expander 1.8 to 5.5 -40 to +125 SPI 10000 2 HW interrupts, 25 mA source/sink per I/O 28-pin SOIC, 28-pin SDIP

Analog and Interface Product Selector Guide 26

SAFETY & SECURITY – Ionization Smoke Detector ICs

Part # Horn Driver Alarm Pattern Alarm

Memory Low Battery

Detection Reverse Battery

Protection Alarm

Interconnect Hush

Timer Power-up

Low Battery Test Operating Temperature

Range (°C) Packages

RE46C120 NFPA Temporal or Continuous Tone No Yes Yes – – – -10 to +60 16-pin PDIP

RE46C121 NFPA Temporal No Yes Yes Yes – – -10 to +60 16-pin PDIP

RE46C122 NFPA Temporal No Yes Yes Yes Yes Yes -10 to +60 16-pin PDIP

RE46C126 Continuous Tone No Yes Yes Yes – – -10 to +60 16-pin PDIP

RE46C127 Continuous Tone No Yes Yes Yes Yes Yes -10 to +60 16-pin PDIP

RE46C128 NFPA Temporal No Yes Yes Yes – Yes -10 to +60 16-pin PDIP

RE46C129 Continuous Tone No Yes Yes Yes – Yes -10 to +60 16-pin PDIP

RE46C152 NFPA Temporal or Continuous Tone No Yes Yes Yes Yes Yes -10 to +60 16-pin PDIP

RE46C162 NFPA Temporal or Continuous Tone Yes Yes Yes Yes Yes Yes -10 to +60 16-pin PDIP

RE46C163 NFPA Temporal or Continuous Tone Yes Yes Yes Yes Yes Yes -10 to +60 16-pin PDIP

RE46C180 NFPA Temporal or Continuous Tone Yes Yes No Yes Yes Yes -10 to +60 16-pin PDIP, 16-pin SOIC

SAFETY & SECURITY – Ionization Smoke Detector Front Ends

Part # Microprocessor Compatible Output Output Options Typical Application Operating Temperature Range (°C) Packages

RE46C112 Yes VOUT 1/4 of VDD or VOUT 1/4 of Detect Input 3V or 3.3V Microprocessor -10 to +60 8-pin PDIP

RE46C114 Yes VOUT 1/2 of VDD or VOUT 1/2 of Detect Input 5V Microprocessor -10 to +60 8-pin PDIP

SAFETY & SECURITY – Piezoelectric Horn Drivers

Part # Operating

Voltage (V) Piezoelectric Horn

Driver LED Driver Voltage

Regulator (V) Low Battery

Detection Interconnect Power good Operating

Temperature Range (°C) Packages

RE46C100 6 to 16 Yes – – – – – -40 to +85 8-pin PDIP, 8-pin SOIC

RE46C101 6 to 16 Yes Yes – – – – -40 to +85 8-pin PDIP, 8-pin SOIC

RE46C104 4 to 8 Yes – – – – – 0 to +50 14-pin PDIP, 14-pin SOIC

RE46C105 6 to 12 Yes Yes 3.3 or 5 Yes – – -40 to +85 14-pin PDIP, 14-pin SOIC

RE46C107 2 to 5 Yes Yes 3 or 3.3 Yes – – 0 to +50 16-pin PDIP, 16-pin SOIC

RE46C108 6 to 12 Yes – 3.3 or 5 – – – -40 to +85 8-pin PDIP, 8-pin SOIC

RE46C109 6 to 12 Yes – 3 Yes Yes Yes -40 to +85 16-pin PDIP, 16-pin SOIC

RE46C117 2 to 5 Yes – – – – – 0 to +50 8-pin PDIP, 8-pin SOIC

RE46C119 6 to 12 Yes – 3 Yes Yes Yes -40 to +85 16-pin PDIP, 16-pin SOIC

SAFETY & SECURITY

SAFETY & SECURITY – Photoelectric Smoke Detector ICs

Part # Horn Driver

Alarm Pattern Alarm

Memory Low Battery

Detection Chamber

Test Alarm

Interconnect Sensitivity

Timer Internal

POR Alternate

Diagnostic Mode Operating

Temperature Range (°C) Packages

RE46C140 NFPA Temporal No Yes Yes Yes Yes Yes – -25 to +75 16-pin PDIP, 16-pin SOIC

RE46C141 NFPA Temporal No Yes Yes Yes – Yes – -25 to +75 16-pin PDIP, 16-pin SOIC

RE46C143 Continuous Tone No Yes Yes Yes – Yes – -25 to +75 16-pin PDIP, 16-pin SOIC

RE46C144 Continuous Tone No Yes Yes Yes Yes Yes – -25 to +75 16-pin PDIP, 16-pin SOIC

RE46C145 NFPA Temporal No Yes Yes Yes Yes Yes Yes -25 to +75 16-pin PDIP, 16-pin SOIC

RE46C165 NFPA Temporal Yes Yes Yes Yes Yes Yes Yes -25 to +75 16-pin PDIP, 16-pin SOIC

RE46C166 Continuous Tone Yes Yes Yes Yes Yes Yes Yes -25 to +75 16-pin PDIP, 16-pin SOIC

RE46C167 NFPA Temporal Yes Yes Yes Yes Yes Yes Yes -25 to +75 16-pin PDIP, 16-pin SOIC

RE46C168 Continuous Tone Yes Yes Yes Yes Yes Yes Yes -25 to +75 16-pin PDIP, 16-pin SOIC

RE46C190 NFPA Temporal or

Continuous Tone No Yes Yes Yes Yes Yes – -10 to +60 16-pin SOIC

ANALOG DESIGN DEVELOPMENT TOOLS

Evaluation, Demonstration and Development Kits

Order # Description Devices Supported

Thermal Management Demonstration and Evaluation Tools

TMPSNS-RTD1 PT100 RTD Evaluation Board MCP6S26, MCP3301, MCP6024, MCP41010,

PIC18F2550, TC1071, MCP6002

MCP9700DM-PCTL

MCP9700 Temperature-to-Voltage Converter PICtail™ Demonstration Board

MCP9800

MCP9700DM-TH1 MCP9700 Thermistor Demonstration Board MCP9700, MCP6S92

MCP9800DM-PCTL MCP9800 Temperature Sensor PICtail™ Demonstration Board MCP9800

MCP9800DM-TS1 MCP9800 Temperature Sensor Demonstration Board MCP9800

MCP9800DM-DL MCP9800 Temperature Data Logger Demonstration Board MCP9800

MCP9800DM-DL2 MCP9800 Temperature Data Logger Demonstration Board 2 MCP9800, MCP101, PIC10F202, 24LC16B

TC72DM-PICTL TC72 Digital Temperature Sensor PICtail™ Demonstration Board TC72

TC74DEMO TC74 Serial Digital Thermal Sensor Demonstration Board TC74

TC77DM-PICTL TC77 Thermal Sensor PICtail™ Demonstration Board TC77

TC642DEMO TC64X/64XB Fan Speed Controller Demonstration Board TC642, TC646, TC647, TC648, TC649

TC650DEMO TC650 Fan Controller Demonstration Board TC650

TC652DEMO TC652 Fan Controller Demonstration Board TC652

TC1047ADM-PICTL TC1047A Temperature-to-Voltage Converter PICtail™ Demonstration Board TC1047A

TMPSNSRD-TCPL1 Thermocouple Reference Design MCP9804, MCP3421

TMPSNSRD-RTD2 RTD Reference Design Board MCP3551, MCP9804

Mixed Signal Demonstration and Evaluation Tools

ADM00333 PIC18F87J72 Evaluation Board PIC18F87J72

ARD00280 PIC18F87J72 Single Phase Energy Meter Reference Design n/a

ARD00330 PIC18F87J72 Energy Monitoring PICtail Plus Daughter Board n/a

DV3201A MCP3XXX Single/Dual ADC MXDEV® Daughter Board MCP3001, MCP3002, MCP3201, MCP3202

DV3204A MCP3204/08 MXDEV® Daughter Board MCP3004, MCP3008, MCP3204, MCP3208

MCP2030DM-TPR MCP2030 Bidirectional Communications Demonstration Kit MCP2030, MCP3421, PIC16F636, TC4421, PIC18F4680

MCP3421EV MCP3421 SOT-23-6 Evaluation Board MCP3421

MCP3421DM-BFG MCP3421 Battery Fuel Gauge Demo Board MCP3421, MCP73831, MCP1702, PIC18F4550

MCP3422EV MCP3422 Evaluation Board MCP3422

MCP3423EV MCP3423 Evaluation Board MCP3423

MCP3424EV MCP3424 Evaluation Board MCP3424

MCP3425EV MCP3425 SOT 23-6 Evaluation Board MCP3425

MCP3221DM-PCTL MCP3221 PICtail™ Demonstration Board MCP3221

MCP3551DM-PCTL MCP3551 Delta-Sigma ADC Demonstration Board MCP3551

MCP355XDV-MS1 MCP355X Sensor Application Developer’s Board MCP3551, MCP3553, MCP3550-50, MCP3550-60

MCP355XDM-TAS MCP355X Tiny Application Sensor Demonstration Board MCP3551, MCP3553, MCP3550-50, MCP3550-60

MCP3901EV-MCU16 MCP3901 ADC Evaluation Board for 16-bit MCUs MCP3901, PIC24F, PIC24H, dsPIC33, PIC18F86J55

MCP3905EV MCP3905 Energy Meter Evaluation Board MCP3905

MCP3905RD-PM1 MCP3905 Energy Meter Reference Design MCP3905

MCP3909EV-MCU16 MCP3909 ADC Evaluation Board for 16-bit MCUs MCP3909

MCP3909RD-3PH1 MCP3909 3-Phase Energy Meter Reference Design MCP3909, PIC18F2520, PIC18F4550

MCP3909RD-3PH3 MCP3909 and dsPIC33F 3-Phase Energy Meter Reference Design MCP3909, dsPIC33FJ128GP706

MCP3909RD-PM1 MCP3909 and PIC18F25K20 Low Cost Power Monitor Reference Design MCP3909, PIC18F25K20

MCP3909RD-1PH1 MCP3909 and PIC18F85J90 Single Phase Energy Meter Reference Design MCP3909, PIC18F85J90

MCP401XEV MCP401X Evaluation Board MCP40D18, MCP4017, MCP4018, MCP4019,

MCP40D17, MCP40D19

Analog and Interface Product Selector Guide 27

ANALOG DESIGN DEVELOPMENT TOOLS

28 Analog and Interface Product Selector Guide

Evaluation, Demonstration and Development Kits

Order # Description Devices Supported

Mixed Signal Demonstration and Evaluation Tools (Continued)

MCP3421DM-WS1 MCP3421 Weight Scale Demo Board MCP3421, MCP6V07, PIC18F4550

MCP402XEV MCP402X Non-Volatile Digital Potentiometer Evaluation Board MCP4021, MCP4022, MCP4023, MCP4024

MCP42XXEV MCP42XX Evaluation Board MCP4231, MCP4241, MCP4251, MCP4261

MCP43XXEV MCP43XX Evaluation Board MCP4331, MCP4341, MCP4351, MCP4361

MCP4XXXDM-DB MCP4XXX Digital Potentiometer Daughter Board MCP4011, MCP4021, MCP42XXX

MCP42XXDM-PTPLS MCP42XX PICtail™ Plus Daughter Board MCP4231, MCP4232, MCP4241, MCP4242, MCP4251,

MCP4252, MCP4261, MCP4262

MCP46XXDM-PTPLS MCP46XX PICtail™ Plus Daughter Board MCP4631, MCP4641, MCP4651, MCP47652, MCP4661,

MCP4662

MCP46XXEV MCP46XX Evaluation Board MCP4631, MCP4641, MCP4651, MCP4661

MCP4725EV MCP4725 SOT 23-6 Evaluation Board MCP4725

MCP4725DM-PTPLS MCP4725 PICtail™ Plus Daughter Board MCP4725

MCP4728EV MCP4728 Quad DAC Evaluation Board MCP4728

ADM00310 MCP3903 ADC Evaluation Board for 16-bit MCUs MCP3903, MCP2200, PIC24, dsPIC33

DV42XXX MCP42XXX Digital Potentiometer Evaluation Board MCP42010, MCP42050, MCP42100

DVMCPA MXDEV® Analog Evaluation System MCP3001/02, MCP3004/08, MCP3201/08,

MCP3204/08

MXSIGDM Mixed Signal PICtail™ Demonstration Board TC132X, MCP330X, MCP320X, MCP482X, MCP492X,

MCP3221, MCP3021, MCP1525

Power Management Demonstration and Evaluation Tools

MCP1252DM-BKLT MCP1252 Charge Pump Backlight Demonstration Board MCP1252

MCP1256/7/8/9EV MCP1256/7/8/9 Charge Pump Evaluation Board MCP1256, MCP1257, MCP1258, MCP1259

MCP1601EV MCP1601 Buck Regulator Evaluation Board MCP1601

MCP1602EV MCP1602 Evaluation Board MCP1602

MCP1603EV MCP1603 Buck Converter Evaluation Board MCP1603

MCP1603RD-TNY MCP1603 Tiny Reference Design MCP1603

MCP1612EV MCP1612 Synchronous Buck Regulator Evaluation Board MCP1612

MCP1630RD-DDBK1 MCP1630 +12V in Dual Output Buck Converter Reference Design MCP1630

MCP1630RD-DDBK3 MCP1630 Bidirectional 4-Cell Li-Ion Charger Reference Design MCP1630V, PIC16F88, MCP6022

MCP1630RD-NMC1 MCP1630 Low-Cost NiMH Battery Charger Reference Design MCP1630, PIC12F683, MCP6292, MCP1702

MCP1630DM-DDBK1 MCP1630 1A Bias Supply Demonstration Board MCP1630

MCP1630DM-DDBS1 MCP1630 Automotive Input Boost Converter Demonstration Board MCP1630, PIC12F683

MCP1630DM-LED2 MCP1630 Boost Mode LED Driver Demonstration Board MCP1630V, PIC12F683, MCP1702

MCP1630RD-LIC1 MCP1630 Li-Ion Multi Bay Battery Charger Reference Design MCP1630

MCP1630RD-LIC2 MCP1630 Low Cost Li-Ion Battery Charger Reference Design MCP1630

MCP1630DM-NMC1 MCP1630 NiMH Battery Charger Demonstration Board MCP1630

MCP1630DM-DDBS2 MCP1630 Coupled Inductor Boost Demonstration Board MCP1630, PIC12F683

MCP1630DM-DDBK4 MCP1630 Automotive Input, Triple Output Converter Demonstration Board MCP1630, PIC12F683

MCP1631RD-DCPC1 MCP1631HV Digitally Controlled Programmable Current Source

Reference Design MCP1631HV, PIC16F616

MCP1631RD-MCC1 MCP1631HV Multi-Chemistry Battery Charger Reference Design MCP1631HV, PIC16F883

MCP1631RD-MCC2 MCP1631HV Multi-Chemistry Battery Charger Reference Design MCP1631HV, PIC16F883

MCP1640EV-SBC MCP1640 Sync Boost Converter Evaluation Board MCP1640

MCP1640RD-4ABC MCP1640 Single Quad-A Battery Boost Converter Reference Design MCP1640, PIC12F617

Analog and Interface Product Selector Guide 29

ANALOG DESIGN DEVELOPMENT TOOLS

Evaluation, Demonstration and Development Kits

Order # Description Devices Supported

Power Management Demonstration and Evaluation Tools (Continued)

MCP1650DM-LED1 MCP1650 3W White LED Demonstration Board MCP1650

MCP1650DM-LED2 MCP1650 Multiple White LED Demonstration Board MCP1650

MCP1650EV MCP1650 Boost Controller Evaluation Board MCP1650

MCP1650DM-DDSC1 MCP1650 SEPIC Power Supply Demonstration Board MCP1650

MCP1726EV MCP1726 1A LDO Evaluation Board MCP1726

MCP73113EV-1SOVP MCP73113 OVP Single Cell Li-Ion Battery Charger Evaluation Board MCP73113, MCP73114

MCP73213EV-2SOVP MCP73213 OVP Dual Cell Li-Ion Battery Charger Evaluation Board MCP73213

MCP73X23EV-LFP MCP73X23 OVP Lithium Iron Phosphate Battery Charger Evaluation Board MCP73123, MCP73223

MCP73871DM-VPCC MCP73871 Demo Board with Voltage Proportional Current Control MCP73871

MCP7381XEV MCP7381X Low-Cost Li-Ion Battery Charger Evaluation Board MCP73811, MCP73812

MCP7382XEV MCP7382X Li-Ion Battery Charger Evaluation Board MCP7382X

MCP73831EV MCP73831 Evaluation Kit MCP73831

MCP73833EV MCP73833 Li-Ion Battery Charger Evaluation Board MCP73833, MCP73834

MCP7383XEV-DIBC MCP73837/8 AC/USB Dual Input Battery Charger Evaluation Board MCP73837, MCP73838

MCP7383XRD-PPM MCP7383X Li-Ion System Power Path Management Reference Design MCP73831, MCP73832, MCP73833, MCP73834

MCP7384XEV MCP7384X Li-Ion Battery Charger Evaluation Board MCP7384X

MCP73855EV MCP73855 Li-Ion Battery Charger Evaluation Board MCP73855

MCP7386XEV MCP7386X Li-Ion Battery Charger Evaluation Board MCP7386X

MCP73871EV MCP73871 Evaluation Board MCP73871

SOT23-3EV-VREG SOT23-3 Voltage Regulator Evaluation Board MCP1701A, MCP1702, MCP1703

SOT223-3EV-VREG SOT223-3 Voltage Regulator Evaluation Board MCP1791, MCP1824, MCP1825, MCP1826

SOT89-3EV-VREG SOT89-3 Voltage Regulator Evaluation Board MCP1700, MCP1701A, MCP1702, MCP1703

TO263-3EV-VREG TO220-3/TO263-3 Voltage Regulator Evaluation Board MCP1790, MCP1825S, MCP1826S, MCP1827S

SOT23-5EV-VREG SOT23-5 Voltage Regulator Evaluation Board MCP1801, MCP1802, TC1014/1015/1185, and other

SOT23-5 LDOs

SOT223-5EV-VREG SOT223-5 Voltage Regulator Evaluation Board MCP1790, MCP1824, MCP1825, MCP1826

TO263-5EV-VREG TO220-5/TO263-5 Voltage Regulator Evaluation Board MCP1790, MCP1791, MCP1825, MCP1826, MCP1827

TC110DM TC110 Boost Converter Demonstration Board TC110, MCP73832

TC115EV TC115 PFM/PWM Boost Converter Evaluation Board TC115

TC1016/17EV TC1016/17 LDO Linear Regulator Evaluation Board TC1016/17

TC1303BDM-DDBK1 TC1303B Demonstration Board TC1303B

TC1303DM-DDBK2 TC1303 DFN Adjustable Output Demonstration Board TC1303C

Interface Products Demonstration and Evaluation Tools

GPIODM-KPLCD GPIO Expander Keypad and LCD Demo Board MCP23008, MCP23S08, MCP23017, MCP23S17,

PIC18F4550, MCP1702

DV251001 MCP2510/2515 CAN Developer’s Kit MCP2515, MCP2510

DV250501 MCP250XX CAN I/O Expanders Developer’s Kit MCP25020, MCP25025, MCP25050, MCP25055

MCP2515DM-PCTL MCP2515 CAN Controller PICtail™ Demonstration Board MCP2515

MCP215XDM MCP215X Data Logger Demonstration Board MCP2150/55

MCP2140DM-TMPSNS MCP2140 IrDA® Wireless Temp Demonstration Board MCP2140

MCP212XDM MCP2120/22 Developer's Board MCP2120, MCP2122

MCP212XEV-DB MCP212X Developer’s Daughter Board MCP212X

ANALOG DESIGN DEVELOPMENT TOOLS

Evaluation, Demonstration and Development Kits

Order # Description Devices Supported

Interface Products Demonstration and Evaluation Tools (Continued)

MCP215X/40EV-DB MCP215X/40 Developer’s Daughter Board MCP2140, MCP2150/55

MCP2150DM MCP2150 Developer's Board MCP2150, MCP2155

MCP2200EV-VCP MCP2200 USB to RS232 Demonstration Board MCP2200

MCP23X08EV MCP23X08 8-bit GPIO Expander Evaluation Board MCP23008, MCP23S08

MCP23X17EV MCP23X17 16-bit GPIO Expander Evaluation Board MCP23017, MCP23S17

MCP2515DM-BM MCP2515 CAN Bus Monitor Demonstration Board MCP2515, MCP2551

MCP2515DM-PTPLS MCP2515 PICtail™ Plus Daughter Board MCP2515, MCP2551

PKSERIAL-SPI1 PICkit™ Serial SPI Demonstration Board 25LC020A, TC77, MCP3201, MCP4822, MCP41010,

MCP6S92, MCP23S08

PKSERIAL-I2C1 PICkit™ Serial I2C™ Demonstration Board 24LC02B, MCP9801, MCP3221, TC1321, MCP23008

Linear Demonstration and Evaluation Tools

MCP6031DM-PTPLS MCP6031 Photodiode PICtail™ Plus Demonstration Board MCP6031

MCP651EV-VOS MCP651 Input Offset Evaluation Board MCP651

MCP661DM-LD MCP661 Line Driver Demo Board MCP661, MCP662, MCP665

MCP6S22DM-PICTL MCP6S22 PGA PICtail™ Demonstration Board MCP6S22

MCP6S2XEV MCP6S2X PGA Evaluation Board MCP6S2X

MCP6SX2DM-PCTLPD MCP6SX2 PGA Photodiode PICtail™ Demonstration Board MCP6S22/92

MCP6SX2DM-PCTLTH MCP6SX2 PGA Thermistor PICtail™ Demonstration Board MCP6S22/92

MCP6V01DM-VOS MCP6V01 Input Offset Demonstration Board MCP6V01, MCP6V03, MCP6V06, MCP6V08

MCP6V01RD-TCPL MCP6V01 Thermocouple Auto-Zeroed Reference Design MCP6V01

PIC16F690DM-PCTLHS Humidity Sensor PICtail™ Demonstration Board MCP6291, PIC16F690

MCP6XXXEV-AMP1 MCP6XXX Ampliﬁ er Evaluation Board 1 MCP6021

MCP6XXXEV-AMP2 MCP6XXX Ampliﬁ er Evaluation Board 2 MCP6021

MCP6XXXEV-AMP3 MCP6XXX Ampliﬁ er Evaluation Board 3 MCP6021

MCP6XXXEV-AMP4 MCP6XXX Ampliﬁ er Evaluation Board 4 MCP6021

MCP6XXXDM-FLTR Active Filter Demonstration Board Kit MCP6271

Analog Blank Evaluation Boards

VSUPEV SOT-23-3 Voltage Supervisor Evaluation Board SOT-23-3 Devices

VSUPEV2 SOT-23-5/6 Voltage Supervisor Evaluation Board SOT-23-5, SOT-23-6 Devices

SC70EV SC70-6 and SOT-23-6/8 to DIP-8 Evaluation Board SC70-6/5/3, SOT-23-8/6/5/3, and DIP-8 Devices

SOIC8EV SOIC/MSOP/TSSOP/DIP 8-pin Evaluation Board 8-pin SOIC, MSOP, TSSOP, DIP Devices

SOIC14EV SOIC/TSSOP/DIP 14-pin Evaluation Board 14-pin SOIC, TSSOP, DIP Devices

TSSOP20EV 20-pin TSSOP and SSOP Evaluation Board TSSOP-20/16/14/8 and SSOP-20

Miscellaneous Analog Demonstration and Evaluation Tools

ADM00344 RE46C190 Demonstration Board RE46C190

EFIELDEV Electrical Field Evaluation Board N/A

HFIELDEV Magnetic Field Evaluation Board N/A

INTRFCEV PSRR and Digital Noise Evaluation Board N/A

30 Analog and Interface Product Selector Guide

Thermal Management Products

MCP9700 Thermistor Demo Board (MCP9700DM-TH1)

The MCP9700 Thermistor Demo Board contains

the analog circuitry to measure temperature. The

board uses BC Components’ 232264055103

NTC thermistor to convert temperature to

resistance. The thermistor is placed in a voltage

divider which converts resistance to voltage. This

voltage is filtered and placed at the MCP6S22

Programmable Gain Amplifier’s (PGA) CH0 input. The PGA

gains and buffers the thermistor.

PT100 RTD Evaluation Board (TMPSNS-RTD1)

This board demonstrates how to bias a

Resistive Temperature Detector (RTD)

and accurately measure temperature.

Up to two RTDs can be connected. The

RTDs are biased using constant current

source and the output voltage is scaled using a differential

amplifier. The output is then connected to a 12-bit

differential Analog-to-Digital Converter (ADC) MCP3301. The

ADC outputs serial data to a PIC18F2550 device using a

Serial Peripheral Interface (SPI). The data is transmitted to a

PC using a USB interface. A Microsoft Excel® macro is used

as a Graphical User Interface (GUI) to acquire the data. The

acquired data is stored in an Excel worksheet and graphed

as a real-time strip chart display.

MCP9800 Temperature Data Logger Demo Board

(MCP9800DM-DL)

Allows users to store up to 128,000

temperature readings from the MCP9800

sensor to the 24LC1025, Microchip’s

1024 Kbit EEPROM. A PIC16F684

MCU communicates with the sensor

and EEPROM. In addition, the PIC MCU interfaces to a PC

using the PICkit™ 1 Flash Starter Kit and transfers the

temperature readings from the EEPROM to the PC. Microsoft

Excel® can be used to view the data.

Mixed Signal Products

MCP3909 and PIC18F85J90 Single Phase Energy

Meter Reference Design (MCP3909RD-1PH1)

The MCP3909/PIC18F85J90 Single Phase

Energy Meter Reference Design is a fully

function single phase meter. The design is

intended to be low cost and is transformerless.

The design uses a half-wave rectified power

supply circuit and a shunt current sensing

element. A single MCP3909 acts as the

analog front end measurement circuitry. The PIC18F85J90

directly drives the LCD glass and displays active energy

consumption.

FEATURED ANALOG DEVELOPMENT TOOLS

MCP3421 Battery Fuel Gauge Demo Board

(MCP3421DM-BFG)

This board is used to demonstrate

the MCP3421 18-bit delta-sigma ADC

for battery fuel gauging applications.

It includes two MCP3421 devices,

MCP73831 (single cell Li-Ion/Li-Polymer Charger) and

PIC18F4550 MCU. The board measures: (1) the battery

voltage and (2) the current coming out from the battery in

the discharging mode and into the battery in the charging

mode using the ADC device (if charging mode is enabled

(optional)). It calculates the total fuel used and also fuel

remaining.

MCP4725 PICtail Plus Daughter Board

(MCP4725DM-PTPLS)

This daughter board demonstrates the

MCP4725 (12 bit DAC with non-volatile

memory) features using the Explorer 16

Development Board and the PICkit Serial

Analyzer.

MCP42XX PICtail Plus Daughter Board

(MCP42XXDM-PTPLS)

The MCP42XX PICtail Plus Daughter

Board is used to demonstrate the

operation of the MCP42XX Digital

Potentiometers. The operation of the

MCP41XX devices is similar to the MCP42XX devices.

Therefore, this demo board can be used as a development

platform for either device family. This board is designed to

be used in conjunction with either the PIC24 Explorer 16

Demo Board or the PICkit Serial Analyzer.

Power Management Products

MCP1631HV Multi-Chemistry Battery Charger

Reference Design (MCP1631RD-MCC1)

This reference design is a complete stand-alone

constant current battery charger for NiMH, NiCd

or constant current/constant voltage for Li-Ion

battery packs. When charging NiMH or NiCd

batteries, the reference design is capable of

charging one, two, three or four batteries connected in series

and one or two series batteries for Li-Ion. This board utilizes

the MCP1631HV (high-speed PIC MCU PWM TSSOP-20) and

PIC16F883 (28-pin SSOP).

MCP73871 Demo Board with Voltage Proportional

Current Control (MCP73871DM-VPCC)

The MCP73871 Demo Board with Voltage

Proportional Current Control is designed to

demonstrate Microchip’s stand-alone linear

Li-Ion battery charger with system power

path and load sharing management control

solution. The MCP73871 integrates the required elements

to meet design challenges when developing new Li-Ion/

Li-Polymer battery powered products.

MCP73831 ( i l

charging one

l ti Th

Analog and Interface Product Selector Guide 31

LIN Serial Analyzer (APGDT001)

The LIN Serial Analyzer development

system enables a Personal Computer (PC)

to communicate with a LIN (Local Interface

Network) bus. The PC program uses a

graphical user interface to enter and

display message frames occurring on the target bus.

USB to UART Converter Evaluation Board

(MCP2200EV-VCP)

The USB to UART Converter Eval board

allows users to store up to 128,000

temperature readings from the MCP9800

sensor to the 24LC1025, Microchip’s

1024Kbit EEPROM. A PIC16F684 MCU

communicates with the sensor and EEPROM. In addition,

the PIC MCU interfaces to a PC using the PICkit 1 Flash

Starter Kit and transfers the temperature readings from the

EEPROM to the PC. Microsoft Excel can be used to view the

data.

Linear Products

MCP6V01 Thermocouple Auto-Zeroed

Ref Design Board (MCP6V01RD-TCPL)

The MCP6V01 design board demonstrates

how to use a difference amplifier

system to measure Electromotive Force

(EMF) voltage at the cold junction of

thermocouple in order to accurately measure temperature

of the thermocouple bead. This can be done by using the

MCP6V01 auto-zeroed op amp because of its ultra low

offset Voltage (VOS) and high Common Mode Rejection Ratio

(CMRR).

MCP651 Input Offset Evaluation Board

(MCP651EV-VOS)

The MCP651 Input Offset Evaluation

board is intended to provide a simple

means to measure the MCP651 Input

Offset Evaluation Board op amp’s input

offset voltage under a variety of operating

conditions. The measured input offset voltage (VOST)

includes the input offset voltage specified in the data sheet

(VOS) plus changes due to: power supply voltage (PSRR),

common mode voltage (CMRR), output voltage (AOL), input

offset voltage drift over temperature (ΔVOS/ΔTA) and 1/f

noise.

MCP6271 Active Filter Eval Kit (MCP6XXXDM-FLTR)

This kit supports active filters designed

by FilterLab® V2.0. These filters are all

pole and are built by cascading first and

second order sections. The kit includes:

one PCB designed to provide mid-supply

biasing to the other printed circuit boards,

four PCBs that support active filter designs with filter order

between n=1 and 8 (output test point for lab equipment

provided) and op amps, zero ohm jumpers, resistors and

capacitors that can be used to help build filters.

MCP73X23 OVP Lithium Iron Phosphate Battery

Charger Evaluation Board (MCP73X23EV-LFP)

The MCP73X23 Lithium Iron Phosphate

Battery Charger Evaluation board

demonstrates the features of Microchip’s

MCP73123 and MCP73223 Lithium Iron

Phosphate (LiFePO4) Battery Charge Management Controller

with Input Overvoltage Protection.

MCP7383X Li-Ion System Power Path Management

Reference Design (MCP7383XRD-PPM)

This reference design is developed to

assist product designers in reducing

product design cycle and time by

utilizing Microchip’s stand-alone Li-Ion

battery charge management controllers

with system power path management. Due to the natural

characteristics of Li-Ion/Li-Polymer batteries, they are the

most popular power sources for mobile devices, however,

extra care in design is always important. System Power Path

Management allows end-users to charge their batteries

without interruption.

MCP1640 Sync Boost Converter Evaluation Board

(MCP1640EV-SBC)

The MCP1640 Synchronous Boost Converter

Evaluation board demonstrates the MCP1640

in two boost-converter applications with

multiple output voltages. It can be used to

evaluate both package options (SOT-23-6 and

2x3-8 DFN). This board was developed to help

engineers reduce the product design cycle

time.

MCP1252 Charge Pump Backlight Demo Board

(MCP1252DM-BKLT)

The MCP1252 board demonstrates the

use of a charge pump device in an LED

application and acts as a platform to

evaluate the MCP1252 device in general.

Light intensity is controlled uniformly

through the use of ballast resistors. A PIC10F206 MCU

provides an enable signal to the MCP1252 and accepts a

push-button input that allows the white LEDs to be adjusted

to five different light intensities.

Interface Products

MCP2515 CAN Bus Monitor Demo Board

(MCP2515DM-BM)

The MCP2515 CAN Bus Monitor Demo

board kit contains two identical boards

which can be connected together to create

a simple two node Controller Area Network

(CAN) bus, which can be controlled and/

or monitored via the included PC interface. The board(s) can

also be connected to an existing CAN bus.

FEATURED ANALOG DEVELOPMENT TOOLS

through the use of

di l

thermocouple in o

32 Analog and Interface Product Selector Guide

ANALOG PRODUCT PART NUMBERS

Part Number Suffix Designations

Ordering Information for all Microchip Analog Products beginning with “TC” prefix

(formerly TelCom Semiconductor Products)

TC 7106 A-60 1 C P L 713

Package Description # of Pins Package Description # of Pins

AB TO-220 3 MB SOT-89 3

AK TO-220 7 MF DFN (3x3) 8

AT TO-220 5 MT SOT-89 5

AV TO-220 (Formed) 5 NB SOT-23B 3

BB TO-220B 3 OA SOIC (N) 8

CB SOT-23A 3 OD SOIC (N) 14

CH SOT-23A 6 OE SOIC (W) 16

CT SOT-23A 5 OG SOIC (W) 24

DB SOT-223 3 OI SOIC (W) 28

EB DDPAK 3 OR SOIC (N) 16

EK DDPAK 7 PA PDIP (N) 8

ET DDPAK 5 PD PDIP (N) 14

HA SOP 8 PE PDIP (N) 16

JA CDIP (N) 8 PF PDIP (N) 24

JD CDIP (N) 14 PG PDIP (W) 24

JE CDIP (N) 16 PI PDIP (W) 28

JG CDIP (W) 24 PJ PDIP (W) 28

JI CDIP (W) 28 PL PDIP (W) 40

JL CDIP (W) 40 QR QSOP (N) 16

KU MQFP 64 RC SOT-143 4

KW MQFP 44 SI SSOP (W) 28

LB SC-70 3 UA MSOP 8

LI PLCC 28 UN MSOP 10

LS PLCC 68 VB DPAK 3

LT SC-70 5 ZB TO-92 3

LW PLCC 44 ZM TO-92 2

Taping Direction:

TR or 713: Standard Taping, blank: no tape and reel

Number of Package Pins (See specific data sheet)

Package Type

Operating Temperature Range:

C: Commercial Range (0°C to +70°C)

E: Extended Industrial Range (-40°C to +85°C)

I: Industrial Range (-25°C to +85°C)

M: Military Range (-55°C to +125°C)

V: See Data Sheet for Specific Temperature Range

(Extra Feature Code and/or Tolerance)* (See specific data sheet)

(Output Voltage or Detect Voltage)* (If applicable, see specific data sheet)

Electrical Performance Grade Option (Variation/Option)*

(If applicable, see specific data sheet)

A: Test Selection Criteria (See specific data sheet)

R: Reversed Pin Layout

Product Part Number (2 to 6 characters, see specific data sheet)

Product Prefix

NOTE: ( )* Used for voltage regulators and detectors.

Analog and Interface Product Selector Guide 33

ANALOG PRODUCT PART NUMBERS

Package Type (see table below)

Operating Temperature Range:

- blank: Commercial Range (0°C to +70°C)

I: Industrial (-40°C to +85°C)

E: Extended Industrial Range (-40°C to +125°C

Supervisor Bond Options:

blank: Not Applicable

Reset Voltage Thresholds or Performance Grade Options:

(1-3 characters, see specific data sheets)

270: 2.7V reset threshold

300: 3.0V reset threshold

315: 3.15V reset threshold

450: 4.5V reset threshold

460: 4.6V reset threshold

475: 4.7V reset threshold

485: 4.85V reset threshold

B: Grade (see specific data sheet)

C: Grade (see specific data sheet)

blank: not applicable

Tape and Reel:

T: Tape and Reel

blank: No Tape and Reel

Product Part Number (3-6 characters, see specific data sheet)

Product Prefix

Package Description # of Pins Tube/Bag Qty. Reel Qty.

TO TO-92 3 1000 n/a

TT SOT-23 3 n/a 3000

OT SOT-23 5 n/a 3000

P PDIP 8 60 n/a

SN SOIC 8 100 3300

ST TSSOP 8 100 2500

MS MSOP 8 100 2500

MF DFN (2x3) 8 n/a 3300

MF DFN (3x3) 8 50 3300

MF DFN (3x3, 10-Pin) 10 120 3300

ST TSSOP 14 96 2500

P PDIP 14 30 n/a

SL SOIC 14 57 2600

P PDIP 18 25 n/a

SO SOIC 18 42 1100

ST TSSOP 20 74 2500

SS SSOP 20 67 1600

ML QFN (6x6) 28 50 1600

ML QFN (4x4) 16 91 3300

Part Number Suffix Designations

Ordering Information for all Microchip Analog Products beginning with “MCP” prefix

MCP xxxxx T - yyy z h / qq

34 Analog and Interface Product Selector Guide

Analog and Interface Product Selector Guide 35

ANALOG PRODUCT PART NUMBERS

Tape and Reel:

TF: Tape and Reel

F: No Tape and Reel

Package Type (2 to 4 characters, see table below)

Product Part Number (3 characters, see specific data sheet)

Product Prefix

Package Description # of Pins Tube Qty. Reel Qty.

E8 PDIP 8 60 n/a

S8 SOIC 8 100 3300

E14 PDIP 14 30 n/a

S14 SOIC 14 57 2600

E16 PDIP 16 30 n/a

S16 SOIC 16 50 2600

SW16 SOIC (300 mil) 16 47 1000

Part Number Suffix Designations

Ordering Information for all Microchip Analog Products beginning with “RE46C” prefix

RE46C xxx yyyy zz