Analog and Interface Product Solutions Fall 2011 Analog and Interface Product Selector Guide Thermal Management Motor Drivers Interface Peripherals Power Management Linear & Mixed-Signal Safety & Security www.microchip.com/analog Table of Contents Thermal Management Mixed Signal Temperature Sensors ............................................ 4 Logic Output Temperature Sensors .................... 4 Voltage Output Temperature Sensors ................. 4 Serial Output Temperature Sensors ................... 4 Brushless DC Fan Controllers and Fan Fault Detectors ............................................... 5 Successive Approximation Register (SAR) A/D Converters ................................................... 19 Delta-Sigma A/D Converters ................................ 20 Energy Measurement ICs ..................................... 20 Dual-Slope A/D Converters .................................. 20 Binary and BCD A/D Converters ........................... 21 Display A/D Converters ....................................... 21 Digital Potentiometers ......................................... 21 Frequency-to-Voltage/Voltage-to-Frequency Converters .......................................................... 23 D/A Converters ................................................... 23 Motor Drivers Stepper Motors, DC Motors and 3 Phase BLDC Fan Controllers ............................................ 5 Power Management Voltage References ............................................... 6 Linear Regulators 50-250 mA LDO Linear Regulators .................... 6 300 mA LDO Linear Regulators ......................... 7 500-800 mA LDO Linear Regulators .................. 7 1A and > LDO Linear Regulators ....................... 8 Application Specific LDO Linear Regulators ........ 8 LDO Regulator Combination Products ..................... 8 Switching Regulators ............................................. 9 Switching Regulator Combination Products.............. 9 PWM Controllers ................................................... 9 Charge Pump DC-to-DC Converters ....................... 10 Inverting or Doubling Charge Pumps ................ 10 Inverting and Doubling Charge Pumps ............. 10 Regulated Charge Pumps................................ 10 CPU/System Supervisors .................................... 10 Voltage Detectors ................................................ 11 Power MOSFET Drivers ........................................ 12 Low-Side Drivers, 0.5A to 1.2A Peak Output Current ............................................... 12 Low-Side Drivers, 1.5A Peak Output Current ..... 12 Low-Side Drivers, 2.0A to 12.0A Peak Output Current ............................................... 13 High-Side/Low-Side Drivers ............................. 13 Synchronous Buck High-Side Drivers ................ 13 Battery Chargers ................................................. 14 Hot Swap Controllers........................................... 14 Interface Linear Featured Analog Development Tools Op Amps ............................................................ 15 High Precision Operational Amplifiers ................... 18 Chopper Stabilized ......................................... 18 Auto-Zero ....................................................... 18 Programmable Gain Amplifiers (PGA) .................... 18 Selectable Gain Amplifiers (SGA) .......................... 18 Comparators ....................................................... 19 Thermal Management .......................................... 31 Mixed Signal ....................................................... 31 Power Management ............................................. 31 Interface ............................................................. 32 Linear................................................................. 32 Controller Area Network (CAN) Products ................ 24 Infrared Products................................................. 24 Ethernet Products ............................................... 24 Passive Access Products ..................................... 24 LIN Transceiver Products...................................... 25 Serial Peripherals ................................................ 25 IEEE 802.15.4 ZigBee(R) RF Transceiver Products ... 25 Stand-alone RF Receiver Products ........................ 25 USB Products ..................................................... 25 Safety & Security Photoelectric Smoke Detector ICs ........................ 26 Ionization Smoke Detector ICs ............................. 26 Ionization Smoke Detector Front Ends .................. 26 Piezoelectric Horn Drivers .................................... 26 Analog Design and Development Tools Thermal Management .......................................... 27 Mixed Signal ....................................................... 27 Power Management ............................................. 28 Interface ............................................................. 29 Linear................................................................. 30 Analog Blank Evaluation Boards ........................... 30 Miscellaneous Analog Demonstration and Evaluation Tools ........................................... 30 Part Number Designations Analog Products with "TC" Prefix .......................... 33 Analog Products with "MCP" Prefix ....................... 34 Analog Products with "RE46C" Prefix .................... 35 2 Analog and Interface Product Selector Guide Are you Looking for Complete Analog & Interface Design Solutions? Microchip's integrated analog technology, Microchip Technology's Stand-Alone Analog & Interface Portfolio peripherals and features are engineered to meet today's demanding design Thermal Power requirements. Our broad spectrum of Management Management Linear Mixed-Signal Interface analog products addresses thermal CAN Peripherals LDO & Switching Op Amps Temperature A/D Converter management, power management, Regulators Sensors Families Infrared battery management, mixed-signal, linear, Programmable Peripherals Charge Pump Fan Speed Digital Gain interface and safety & security solutions. DC/DC Converters Controllers/ Potentiometers Amplifiers LIN Transceivers Fan Fault Combined with "Intelligent Analog" Power MOSFET D/A Converters Comparators Detectors Serial Peripherals Drivers microcontrollers, Microchip offers an V/F and F/V Ethernet Controllers extensive analog portfolio for thousands PWM Controllers Converters Motor Drive Safety & Security USB Peripheral of high-performance design applications System Supervisors Energy Stepper and DC Photoelectric Measurement in the automotive, communications Voltage Detectors Smoke Detectors ICs 3 Brushless (wireless), consumer, computing and DC Fan Controller Voltage References Ionization Smoke industrial control markets. Detectors Li-Ion/Li-Polymer Our broad portfolio of stand-alone Battery Chargers Ionization Smoke Detector Front Ends analog and interface devices offers highly integrated solutions that combine Piezoelectric Horn Drivers various analog functions in space-saving packages and support a variety of bus interfaces. Many of these devices support functionality that enhances the analog features currently available on PIC(R)microcontrollers. Want a Business Partner, Not Just a Vendor? Successful companies recognize the value of a strategic supplier relationship to help them deliver innovative products to their markets in a timely manner. They trust their suppliers to furnish quality components for current design opportunities as well as provide technology road maps and innovative solutions to stay ahead of tomorrow's design trends. Microchip Technology provides low-risk product development, lower total system cost and faster time to market to more than 45,000 of these successful companies worldwide. Headquartered in Chandler, Arizona, Microchip offers outstanding technical support along with dependable delivery and quality. Founded in 1989, Microchip's business model is based on a series of guiding values that aim to establish successful customer partnerships by exceeding expectations for products, services and attitude. Continuous improvement, technology innovation and the pursuit of the highest quality possible drive Microchip's company culture. The result is a worldwide organization dedicated to delivering whole product solutions which include high performance silicon devices, easy-to-use development tools, outstanding technical support and sophisticated technical documentation. Are Quality and Delivery a Concern? Need Additional Support and Resources? Microchip is committed to supporting its customers by helping design engineers develop products faster and more efficiently. Customers can access three main service areas at www.microchip.com. The Support area provides a fast way to get questions answered. The Sample area offers evaluation samples of any Microchip device. microchipDIRECT provides 24-hour pricing, ordering, inventory and credit for convenient purchasing of all Microchip devices and development tools. This site also features online programming capabilities. Finally, the Training area offers opportunities to expand your knowledge with Microchip's online web seminars and handson courses at our worldwide Technical Training Centers. Our seminars and training classes are designed to fit your schedule and offer an overview of many product, development tool and application topics. Visit www.microchip.com/training for class content and schedules. Have you ever encountered a technical dilemma at a critical point in your design development and your supplier was not available to answer your questions? Microchip's first ever 24/7 global technical support line brings technical support resources any time help is needed. Because some technical problems require hands-on assistance in order to be resolved quickly, Microchip has also developed a global team of field applications engineers and field sales engineers for local assistance. Microchip's quality systems are certified according to the International Organization for Standards/Technical Specification (ISO/TS)-16949:2002 requirements. This demonstrates that the Company's quality systems meet the most stringent industry quality-management system standards, resulting in high-quality semiconductor products. Direct control over manufacturing resources allows shortened design and production cycles. By owning the wafer fabrication facilities and the majority of the test and assembly operations, and by employing proprietary statistical process control techniques, Microchip has been able to achieve and maintain high production yields. Analog and Interface Product Selector Guide 3 THERMAL MANAGEMENT THERMAL MANAGEMENT PRODUCTS - Temperature Sensors Part # Typical Accuracy (C) Maximum Accuracy @ 25C (C) Maximum Temperature Range (C) Vcc Range (V) Maximum Supply Current (A) Features Packages Logic Output Temperature Sensors TC6501 0.5 3 -55 to +125 +2.7 to +5.5 40 Cross to MAX6501, Open-drain 5-pin SOT-23A TC6502 0.5 3 -55 to +125 +2.7 to +5.5 40 Cross to MAX6502, Push-pull 5-pin SOT-23A TC6503 0.5 3 -55 to +125 +2.7 to +5.5 40 Cross to MAX6503, Open-drain 5-pin SOT-23A TC6504 0.5 3 -55 to +125 +2.7 to +5.5 40 Cross to MAX6504, Push-pull 5-pin SOT-23A TC620 1 3 -40 to +125 +4.5 to +18 400 Two resistor-programmable trip points 8-pin PDIP, 8-pin SOIC TC621 Note 1 Note 1 -40 to +85 +4.5 to +18 400 Requires external thermistor, resistor-programmable trip points 8-pin PDIP, 8-pin SOIC TC622 1 5 -40 to +125 +4.5 to +18 600 Dual output, TO-220 for heat sink mounting, resistor-programmable trip points 8-pin PDIP, 8-pin SOIC, 5-pin TO-220 TC623 1 3 -40 to +125 +2.7 to +4.5 250 Two resistor-programmable trip points 8-pin PDIP, 8-pin SOIC TC624 1 5 -40 to +125 +2.7 to +4.5 300 Dual output, resistor-programmable trip points 8-pin PDIP, 8-pin SOIC MCP9501 1 4 -40 to +125 +2.7 to +5.5 40 Active-High, Push-Pull Output, Rising Temperature Switch 5-pin SOT-23 MCP9502 1 4 -40 to +125 +2.7 to +5.5 40 Active-Low, Open Drain Output, Rising Temperature Switch 5-pin SOT-23 MCP9503 1 4 -40 to +125 +2.7 to +5.5 40 Active-High, Push-Pull Output, Falling Temperature Switch 5-pin SOT-23 MCP9504 1 4 -40 to +125 +2.7 to +5.5 40 Active-Low, Open Drain Output, Falling Temperature Switch 5-pin SOT-23 MCP9509 0.5 NS -40 to +125 +2.7 to +5.5 50 Resistor-programmable temperature switch 5-pin SOT-23 MCP9510 0.5 NS -40 to +125 +2.7 to +5.5 80 Resistor-programmable temperature switch 6-pin SOT-23 Voltage Output Temperature Sensors MCP9700 1 4 -40 to +125 +2.3 to +5.5 12 Linear Active Thermistor(R) IC, Temperature slope: 10 mV/C 3-pin TO-92, 5-pin SC-70, 3-pin SOT-23 MCP9701 1 4 -10 to +125 +3.1 to +5.5 12 Linear Active Thermistor(R) IC, Temperature slope: 19.53 mV/C, cross to MAX6612 3-pin TO-92, 5-pin SC-70, 3-pin SOT-23 MCP9700A 1 2 -40 to +125 +2.3 to +5.5 12 Linear Active Thermistor(R) IC, Temperature slope: 10 mV/C 3-pin TO-92, 5-pin SC-70, 3-pin SOT-23 MCP9701A 1 2 -40 to +125 +3.1 to +5.5 12 Linear Active Thermistor(R) IC, Temperature slope: 19.53 mV/C, cross to MAX6612 3-pin TO-92, 5-pin SC-70, 3-pin SOT-23 TC1046 0.5 2 -40 to +125 +2.7 to +4.4 60 High precision temperature-to-voltage converter, 6.25 mV/C 3-pin SOT-23B TC1047 0.5 2 -40 to +125 +2.7 to +4.4 60 High precision temperature-to-voltage converter, 10 mV/C 3-pin SOT-23B TC1047A 0.5 2 -40 to +125 +2.5 to +5.5 60 High precision temperature-to-voltage converter, 10 mV/C 3-pin SOT-23B Serial Output Temperature Sensors MCP9800 0.5 1 -55 to +125 +2.7 to +5.5 400 MCP9801 0.5 1 -55 to +125 +2.7 to +5.5 400 MCP9802 0.5 1 -55 to +125 +2.7 to +5.5 400 MCP9803 0.5 1 -55 to +125 +2.7 to +5.5 400 SMbus/I2CTM compatible interface, 0.0625C to 0.5C adj. resolution, Power-saving one-shot temperature measurement SMbus/I2CTM compatible interface, 0.0625C to 0.5C adj. resolution, Power-saving one-shot temperature measurement, multi-drop capability SMbus/I2CTM compatible interface with time out, 0.0625C to 0.5C adj. resolution, Power-saving one-shot temperature measurement SMbus/I2CTM compatible interface with time out, 0.0625C to 0.5C adj. resolution, Power-saving one-shot temperature measurement, Multi-drop capability MCP9804 0.25 1 -40 to +125 +2.7 to +5.5 400 User programmable temperature limits with alert output, 1C temp. accuracy from -40C to +125C 8-pin MSOP, 8-pin 2x3 DFN MCP9805 0.5 1(2) -20 to +125 +3.0 to +3.6 400 JEDEC compatible register set, SMbus/I2CTM compatible interface, Programmable, Shut-down modes and EVENT output 8-pin TSSOP, 8-pin 2x3 DFN MCP9843 0.5 1 (2) -20 to +125 +3.0 to +3.6 500 Compliant to JEDEC TS2002 specification 8-pin TSSOP, 8-pin 2x3 DFN, 8-pin 2x3 TDFN MCP98242 0.5 1(2) -20 to +125 +3.0 to +3.6 400 Same temperature sensor as MCP9805 plus integrated DDR2 Serial Presence Detect EEPROM 8-pin TSSOP, 8-pin 2x3 DFN MCP98243 5-pin SOT-23 8-pin MSOP, 8-pin SOIC 5-pin SOT-23 8-pin MSOP, 8-pin SOIC 1 3 -40 to +125 +3.0 to +3.6 500 Serial output temperature sensor with integrated EEPROM 8-pin TSSOP, 8-pin 2x3 DFN, 8-pin 2x3 TDFN TC77 0.5 1 -55 to +125 +2.7 to +5.5 400 SPI compatible interface, 0.0625C temperature resolution 5-pin SOT-23A, 8-pin SOIC TC72 0.5 1 -55 to +125 +2.65 to +5.5 400 SPI compatible interface, Power-saving one-shot temperature measurement, 0.25C temperature resolution 8-pin MSOP, 8-pin 3x3 DFN TC74 0.5 2 -40 to +125 +2.7 to +5.5 350 2 SMbus/I CTM compatible interface, 1C temperature resolution 5-pin SOT-23A, 5-pin TO-220 Note 1: These devices use an external temperature sensor. Accuracy of the total solution is a function of the accuracy of the external sensor. 2: Maximum accuracy measured at 85C. Analog and Interface Product Selector Guide 4 Serial Output Temperature Sensors Typical Accuracy (C) Maximum Accuracy @ 25C (C) Maximum Temperature Range (C) Vcc Range (V) Maximum Supply Current (A) TCN75A 0.5 2 -40 to +125 +2.7 to +5.5 500 TCN75 0.5 2 -55 to +125 +2.7 to +5.5 1,000(3) Part # Features Packages SMbus/I2CTM compatible interface, power-saving one-shot temperature measurement, multi-drop capability, 0.0625C to 0.5C adjustable temperature resolution 8-pin MSOP, 8-pin SOIC SMbus/I2CTM compatible interface, multi-drop capability, interrupt output, 0.5C temperature resolution 8-pin MSOP, 8-pin SOIC Note 1: These devices use an external temperature sensor. Accuracy of the total solution is a function of the accuracy of the external sensor. 2: Maximum accuracy measured at 85C. 3: TCN75 idle current is 250 mA. This device also has a Software Shutdown mode that reduces supply current to <1 A. THERMAL MANAGEMENT PRODUCTS - Brushless DC Fan Controllers and Fan Fault Detectors Part # Typical Accuracy (C) Description Maximum Accuracy @ 25C (C) Maximum Temperature Range (C) Vcc Range (V) Maximum Supply Current (A) TC642 Fan Manager Note 1 Note 1 -40 to +85 +3.0 to +5.5 1,000 TC642B Fan Manager Note 1 Note 1 -40 to +85 +3.0 to +5.5 400 TC646 Fan Manager Note 1 Note 1 -40 to +85 +3.0 to +5.5 1,000 TC646B Fan Manager Note 1 Note 1 -40 to +85 +3.0 to +5.5 400 TC647 Fan Manager Note 1 Note 1 -40 to +85 +3.0 to +5.5 1,000 TC647B Fan Manager Note 1 Note 1 -40 to +85 +3.0 to +5.5 400 TC648 Fan Manager Note 1 Note 1 -40 to +85 +3.0 to +5.5 1,000 TC648B Fan Manager Note 1 Note 1 -40 to +85 +3.0 to +5.5 400 TC649 Fan Manager Note 1 Note 1 -40 to +85 +3.0 to +5.5 1,000 TC649B Fan Manager Note 1 Note 1 -40 to +85 +3.0 to +5.5 TC650 Fan Manager 1 3 -40 to +125 TC651 Fan Manager 1 3 TC652 Fan Manager 1 TC653 Fan Manager 1 Features Packages FanSenseTM Fan Monitor, Minimum fan speed control 8-pin PDIP, 8-pin SOIC, 8-pin MSOP FanSenseTM Fan Monitor, Minimum fan speed control, Fan auto-restart 8-pin PDIP, 8-pin SOIC, 8-pin MSOP FanSenseTM Fan Monitor, Auto-shutdown 8-pin PDIP, 8-pin SOIC, 8-pin MSOP FanSenseTM Fan Monitor, Auto-shutdown, Fan auto-restart 8-pin PDIP, 8-pin SOIC, 8-pin MSOP FanSenseTM Fan Monitor, Minimum fan speed control 8-pin PDIP, 8-pin SOIC, 8-pin MSOP FanSenseTM Fan Monitor, Minimum fan speed control, Fan auto-restart 8-pin PDIP, 8-pin SOIC, 8-pin MSOP Overtemperature alert, Auto-shutdown 8-pin PDIP, 8-pin SOIC, 8-pin MSOP Overtemperature alert, Auto-shutdown, Fan auto-restart 8-pin PDIP, 8-pin SOIC, 8-pin MSOP FanSenseTM Fan Monitor, Auto-shutdown 8-pin PDIP, 8-pin SOIC, 8-pin MSOP 400 FanSenseTM Fan Monitor, Auto-shutdown, Fan auto-restart 8-pin PDIP, 8-pin SOIC, 8-pin MSOP +2.8 to +5.5 90 Overtemperature alert 8-pin MSOP -40 to +125 +2.8 to +5.5 90 Overtemperature alert, Auto-shutdown 8-pin MSOP 3 -40 to +125 +2.8 to +5.5 90 FanSenseTM Fan Monitor, Overtemperature alert 8-pin MSOP 3 -40 to +125 +2.8 to +5.5 90 FanSenseTM Fan Monitor, Overtemperature alert, Auto-shutdown 8-pin MSOP TC654 Dual SMbus Fan Manager Note 1 Note 1 -40 to +85 +3.0 to +5.5 320 FanSenseTM Fan Monitor, RPM data 10-pin MSOP TC655 Dual SMbus Fan Manager Note 1 Note 1 -40 to +85 +3.0 to +5.5 320 FanSenseTM Fan Monitor, RPM data, Overtemperature alert 10-pin MSOP TC664 Single SMbus Fan Manager Note 1 Note 1 -40 to +85 +3.0 to +5.5 320 FanSenseTM Fan Monitor, RPM data 10-pin MSOP TC665 Single SMbus Fan Manager Note 1 Note 1 -40 to +85 +3.0 to +5.5 320 FanSenseTM Fan Monitor, RPM data, Overtemperature alert 10-pin MSOP TC670 Predictive Fan Fault Detector N/A N/A -40 to +85 +3.0 to +5.5 150 FanSenseTM Fan Monitor, Programmable threshold 6-pin SOT-23 Note 1: These devices use an external temperature sensor. Accuracy of the total solution is a function of the accuracy of the external sensor. MOTOR DRIVERS MOTOR DRIVER PRODUCTS - Stepper Motors, DC Motors and 3 Phase BLDC Fan Controllers Part # MTS62C19A MTS2916A Motor Type One Bipolar Stepper Motor or Two DC Motors One Bipolar Stepper Motor or Two DC Motors Input Voltage Range (V) Internal/ External FETs Output Current (mA) 10.0 to 40.0 Internal 750 10.0 to 40.0 Internal 750 Control Scheme Direct PWM Input, Current Limit Control, Microstepping Direct PWM Input, Current Limit Control, Microstepping Motor Speed Output Shutdown Protection Temperature Operating Range (C) No Overtemperature, Under Voltage -20 to +85 Dual Full Bridge Motor Driver for Stepper Motors, Pin compatible with Allegro 6219 24-pin SOIC No Overtemperature, Under Voltage -20 to +85 Dual Full Bridge Motor Driver for Stepper Motors, Pin compatible with Allegro 2916 24-pin SOIC Short Circuit Overtemperature, Motor Lock-up Short Circuit Overtemperature, Motor Lock-up Short Circuit Overtemperature, Motor Lock-up -30 to +95 3-Phase BLDC Sinusoidal Sensorless Fan Motor Driver, Overcurrent limitation Thermally Enhanced 8-pin SOP -30 to +95 3-Phase BLDC Sinusoidal Sensorless Fan Motor Driver, Overcurrent limitation 10-pin MSOP -40 to +85 3-Phase BLDC Sinusoidal Sensorless Fan Motor Driver, Direction control, Overcurrent limitation 10-pin TDFN 3x3 MTD6501C 3 Phase Brushless Fan 2.0 to 14.0 Internal 800 Sensorless Sinusoidal Frequency Generator MTD6501D 3 Phase Brushless Fan 2.0 to 14.0 Internal 500 Sensorless Sinusoidal Frequency Generator MTD6502B 3 Phase Brushless Fan 2.0 to 5.5 Internal 750 Sensorless Sinusoidal Frequency Generator Features Packages Analog and Interface Product Selector Guide 5 POWER MANAGEMENT POWER MANAGEMENT - Voltage References Vcc Range (V) Part # Output Voltage (V) Max. Load Current (mA) Initial Accuracy (max.%) Temperature Coefficient (ppm/C) Maximum Supply Current (A @ 25C) Packages MCP1525 2.7 to 5.5 2.5 2 1 50 100 3-pin TO-92, 3-pin SOT-23B MCP1541 4.3 to 5.5 4.096 2 1 50 100 3-pin TO-92, 3-pin SOT-23B POWER MANAGEMENT - Linear Regulators Part # Max. Input Voltage (V) Output Voltage (V) Output Current (mA) Junction Temperature Range (C) Typical Active Current (A) Typical Dropout Voltage @ Max. Iout (mV) Typical Output Voltage Accuracy (%) 50 -40 to +125 55 45 0.4 Ceramic output capacitor stable, Shutdown, Reference bypass input 5-pin SOT-23A Features Packages 50 mA to 250 mA Low-Dropout Linear Regulators TC2014 6.0 1.8, 2.7, 2.8, 3.0, 3.3 TC1014 6.0 1.8, 2.5, 2.7, 2.8, 2.85, 3.0, 3.3, 3.6, 4.0, 5.0 50 -40 to +125 50 85 0.5 Shutdown, Reference bypass input 5-pin SOT-23A TC2054 6.0 1.8, 2.7, 2.8, 3.0, 3.3 50 -40 to +125 55 45 0.4 Ceramic output capacitor stable, Shutdown, Error output 5-pin SOT-23A TC1054 6.0 1.8, 2.5, 2.7, 2.8, 2.85, 3.0, 3.3, 3.6, 4.0, 5.0 50 -40 to +125 50 85 0.5 TC1070 6.0 1.23 VIN 50 -40 to +125 50 85 - TC1072 6.0 2.5, 2.7, 2.8, 2.85, 3.0, 3.3, 3.6, 4.0, 5.0 50 -40 to +125 50 85 0.5 TC1223 6.0 2.5, 2.7, 2.8, 3.0, 3.3, 3.6, 4.0, 5.0 50 -40 to +125 50 85 0.5 Shutdown 5-pin SOT-23A MCP1790 30 3.0, 3.3, 5.0 70 -40 to +125 70 500 0.2 Ceramic output capacitor stable 3-pin SOT-223, 3-pin DDPAK MCP1791 30 3.0, 3.3, 5.0 70 -40 to +125 70 500 0.2 5-pin SOT-223, 5-pin DDPAK TC1016 6.0 1.8, 2.7, 2.8, 3.0 80 -40 to +125 50 150 0.5 TC2015 6.0 1.8, 2.5, 2.6, 2.7, 2.8, 2.85, 3.0, 3.3, 5.0 100 -40 to +125 55 90 0.4 Ceramic output capacitor stable, Shutdown, Power good Ceramic output capacitor stable, Shutdown Ceramic output capacitor stable, Shutdown, Reference bypass input TC1015 6.0 1.8, 2.5, 2.7, 2.8, 2.85, 3.0, 3.3, 3.6, 4.0, 5.0 100 -40 to +125 50 180 0.5 Shutdown, Reference bypass input 5-pin SOT-23A TC2055 6.0 1.8, 2.7, 2.8, 3.0, 3.3 100 -40 to +125 55 90 0.4 Ceramic output capacitor stable, Shutdown, Error output 5-pin SOT-23A TC1055 6.0 1.8, 2.5, 2.7, 2.8, 2.85, 3.0, 3.3, 3.6, 4.0, 5.0 100 -40 to +125 50 180 0.5 TC1071 6.0 1.23 VIN 100 -40 to +125 50 180 - TC1073 6.0 2.5, 2.7, 2.8, 2.85, 3.0, 3.3, 3.6, 4.0, 5.0 100 -40 to +125 50 180 0.5 Shutdown, Reference bypass input, Error output 6-pin SOT-23A TC1224 6.0 2.5, 2.7, 2.8, 3.0, 3.3, 3.6, 4.0, 5.0 100 -40 to +125 50 180 0.5 Shutdown 5-pin SOT-23A TC1188 6.0 1.8, 2.8, 2.84, 3.15 120 -40 to +125 50 130 0.5 Shutdown 5-pin SOT-23A TC1189 6.0 1.8, 2.8, 2.84, 3.15 120 -40 to +125 50 130 0.5 Shutdown 5-pin SOT-23A TC2185 6.0 1.8, 2.7, 2.8, 3.0, 3.3 150 -40 to +125 55 140 0.4 Ceramic output capacitor stable, Shutdown, Reference bypass input 5-pin SOT-23A TC1185 6.0 1.8, 2.5, 2.7, 2.8, 2.85, 3.0, 3.3, 3.6, 4.0, 5.0 150 -40 to +125 50 270 0.5 Shutdown, Reference bypass input 5-pin SOT-23A 5-pin SOT-23A Shutdown, Error output 5-pin SOT-23A Shutdown, Adjustable 5-pin SOT-23A Shutdown, Reference bypass input, Error output 6-pin SOT-23A 5-pin SC-70, 5-pin SOT-23A 5-pin SOT-23A Shutdown, Error output 5-pin SOT-23A Shutdown, Adjustable 5-pin SOT-23A TC2186 6.0 1.8, 2.7, 2.8, 3.0, 3.3 150 -40 to +125 55 140 0.4 Ceramic output capacitor stable, Shutdown, Error output TC1186 6.0 1.8, 2.5, 2.7, 2.8, 2.85, 3.0, 3.3, 3.6, 4.0, 5.0 150 -40 to +125 50 270 0.5 Shutdown, Error output 5-pin SOT-23A TC1187 6.0 1.23 VIN 150 -40 to +125 50 270 - Shutdown, Adjustable 5-pin SOT-23A Ceramic output capacitor stable, Shutdown 5-pin SOT-23A, 5-pin SC-70 5-pin SOT-23, 5-pin SOT-89, 5-pin SOT-223, 8-pin 2x3 TDFN 3-pin SOT-23, 3-pin SOT-89, 3-pin SOT-223, 8-pin 2x3 TDFN TC1017 6.0 1.8, 2.6, 2.7, 2.8, 2.85, 2.9, 3.3, 3.4 150 -40 to +125 53 285 0.5 MCP1754 16 1.8, 2.5, 2.7, 2.8, 2.85, 3.0, 3.3, 3.6, 4.0, 5.0 150 -40 to +125 56 300 2 70 dB PSRR MCP1754S 16 1.8, 2.5, 2.7, 2.8, 2.85, 3.0, 3.3, 3.6, 4.0, 5.0 150 -40 to +125 56 300 2 70 dB PSRR Analog and Interface Product Selector Guide 6 POWER MANAGEMENT - Linear Regulators (Continued) Part # Max. Input Voltage (V) Output Voltage (V) Output Current (mA) Junction Temperature Range (C) Typical Active Current (A) Typical Dropout Voltage @ Max. Iout (mV) Typical Output Voltage Accuracy (%) Features Packages 50 mA to 250 mA Low-Dropout Linear Regulators (Continued) Ceramic output capacitor stable, Shutdown, High PSRR 5-pin SOT-23A Shutdown, High PSRR 5-pin SOT-23, 5-pin SOT-89, 3-pin SOT-89, 3-pin SOT-223 0.4 1.0 F ceramic cap stable, Short-circuit protection 3-pin TO-92, 3-pin SOT-23A, 3-pin SOT-89 380 0.5 10V max. input voltage 3-pin TO-92, 3-pin SOT-23A, 3-pin SOT-89 MCP1801 10 0.9, 1.2, 1.8, 2.5, 3.0, 3.3, 5.0, 6.0 150 -40 to +85 25 250 0.4 MCP1804 28 1.8 to 18 150 -40 to +85 50 1300 2 MCP1700 6.0 1.2, 1.8, 2.5, 3.0, 3.3, 5.0 250 -40 to +125 1.6 300 MCP1701A 10 1.8, 2.5, 3.0, 3.3, 5.0 250 -40 to +85 1.6 MCP1702 13.2 1.2, 1.5, 1.8, 2.5, 2.8, 3.0, 3.3, 4.0, 5.0 250 -40 to +125 2 650 0.4 Ceramic output capacitor stable, Ultra-low ground current, 13.2V VIN max. 3-pin TO-92, 3-pin SOT-23A, 3-pin SOT-89 MCP1703 16 1.2, 1.5, 1.8, 2.5, 2.8, 3.0, 3.3, 4.0, 5.0 250 -40 to +125 2 650 0.4 Ceramic output capacitor stable, Ultra-low ground current, 16V VIN max. 3-pin SOT-23A, 3-pin SOT-89, 3-pin SOT-223 Shutdown, Reference bypass input 8-pin MSOP, 8-pin SOIC 300 mA Low-Dropout Linear Regulators TC1107 6.0 2.5, 2.7, 2.8, 3.0, 3.3, 5.0 300 -40 to +125 50 240 0.5 TC1108 6.0 2.5, 2.7, 2.8, 3.0, 3.3, 5.0 300 -40 to +125 50 240 0.5 TC1173 6.0 2.5, 2.7, 2.8, 3.0, 3.3, 5.0 300 -40 to +125 50 240 0.5 TC1174 6.0 1.23 VIN 300 -40 to +125 50 240 TC1269 6.0 2.5, 2.8, 3.0, 3.3, 5.0 300 -40 to +125 50 MCP1802 10 0.9, 1.2, 1.8, 2.5, 3.0, 3.3, 5.0, 6.0 300 -40 to +85 25 MCP1824 6.0 Fixed: 0.8, 1.2, 1.8, 2.5, 3.0, 3.3, 5.0 Adjustable: 0.8 to 5.0 300 -40 to +125 MCP1824S 6.0 0.8, 1.2, 1.8, 2.5, 3.0, 3.3, 5.0 300 3-pin SOT-223 Shutdown, Reference bypass input, Error output 8-pin MSOP, 8-pin SOIC - Shutdown, Reference bypass input, Adjustable 8-pin MSOP, 8-pin SOIC 240 0.5 Shutdown, Reference bypass input 8-pin MSOP 250 0.4 Ceramic output capacitor stable, Shutdown, High PSRR 5-pin SOT-23A 120 200 0.5 Ceramic output capacitor stable, Shutdown, Power good 5-pin SOT-223, 5-pin SOT-23 -40 to +125 120 200 0.5 Ceramic output capacitor stable 3-pin SOT-223 500 mA to 800 mA Low-Dropout Linear Regulators TC1262 6.0 2.5, 2.8, 3.0, 3.3, 5.0 500 -40 to +125 80 350 0.5 Overtemperature protection, Overcurrent protection 3-pin TO-220, 3-pin DDPAK, 3-pin SOT-223 TC1263 6.0 2.5, 2.8, 3.0, 3.3, 5.0 500 -40 to +125 80 350 0.5 Shutdown, Reference bypass input, Error output 8-pin SOIC, 5-pin TO-220, 5-pin DDPAK TC1268 6.0 2.5 500 -40 to +125 80 350 0.5 Shutdown, Reference bypass input, Error output 8-pin SOIC 8-pin 2x3 DFN, 8-pin SOIC MCP1725 6.0 0.8, 1.2, 1.8, 2.5, 3.0, 3.3, 5.0 500 -40 to +125 120 210 0.5 Ceramic output capacitor stable, Shutdown, CDELAY, Power good MCP1825 6.0 Fixed: 0.8,1.2,1.8, 2.5, 3.0, 3.3, 5 Adjustable: 0.8 to 5.0 500 -40 to +125 120 210 0.5 Ceramic output capacitor stable, Shutdown, Power good 5-pin TO-220, 5-pin DDPAK, 5-pin SOT-223 MCP1825S 6.0 0.8,1.2,1.8, 2.5, 3.0, 3.3, 5 500 -40 to +125 120 210 0.5 Ceramic output capacitor stable 3-pin TO-220, 3-pin DDPAK, 3-pin SOT-223 TC1264 6.0 1.8, 2.5, 3.0, 3.3 800 -40 to +125 80 450 0.5 Overtemperature protection, Overcurrent protection 3-pin TO-220, 3-pin DDPAK, 3-pin SOT-223 TC1265 6.0 1.8, 2.5, 3.0, 3.3 800 -40 to +125 80 450 0.5 Shutdown, Reference bypass input, Error output 8-pin SOIC, 5-pin TO-220, 5-pin DDPAK TC2117 6.0 1.8, 2.5, 3.0, 3.3 800 -40 to +125 80 600 0.5 Overtemperature protection, Overcurrent protection 3-pin SOT-223, 3-pin DDPAK Analog and Interface Product Selector Guide 7 POWER MANAGEMENT - Linear Regulators (Continued) Part # Max. Input Voltage (V) Output Voltage (V) Output Current (mA) Junction Temperature Range (C) Typical Active Current (A) Typical Dropout Voltage @ Max. Iout (mV) Typical Output Voltage Accuracy (%) Features Packages 1A and Above Low-Dropout Linear Regulators MCP1726 6.0 Fixed: 0.8,1.2,1.8, 2.5, 3.0, 3.3, 5 Adjustable: 0.8 to 5.0 1000 -40 to +125 140 300 0.4 Ceramic output capacitor stable, Shutdown, CDELAY, Power good 8-pin 3x3 DFN, 8-pin SOIC MCP1826 6.0 Fixed: 0.8,1.2,1.8, 2.5, 3.0, 3.3, 5 Adjustable: 0.8 to 5.0 1000 -40 to +125 140 300 0.5 Ceramic output capacitor stable, Shutdown, Power good 5-pin TO-220, 5-pin DDPAK, 5-pin SOT-223 MCP1826S 6.0 0.8,1.2,1.8, 2.5, 3.0, 3.3, 5 1000 -40 to +125 140 300 0.5 Ceramic output capacitor stable 3-pin TO-220, 3-pin DDPAK, 3-pin SOT-223 MCP1727 6.0 Fixed: 0.8,1.2,1.8, 2.5, 3.0, 3.3, 5 Adjustable: 0.8 to 5.0 1500 -40 to +125 140 330 0.5 Ceramic output capacitor stable, Shutdown, CDELAY, Power good 8-pin 3x3 DFN, 8-pin SOIC MCP1827 6.0 Fixed: 0.8,1.2,1.8, 2.5, 3.0, 3.3, 5 Adjustable: 0.8 to 5.0 1500 -40 to +125 140 330 0.5 Ceramic output capacitor stable, Shutdown, Power good 5-pin DDPAK, 5-pin TO-220 MCP1827S 6.0 0.8,1.2,1.8, 2.5, 3.0, 3.3, 5 1500 -40 to +125 140 330 0.5 Ceramic output capacitor stable 3-pin DDPAK, 3-pin TO-220 Application Specific Low-Dropout Linear Regulators TC1266 6.0 3.3 200 -5 to +70 230 200 1.0 PCI compliant 8-pin SOIC, 8-pin MSOP TC1267 6.0 3.3 400 -5 to +70 230 300 1.0 PCI compliant 5-pin DDPAK 4,000(1) -40 to +85 50 100(1) 2.0 Shutdown, External transistor 5-pin SOT-23A 100 -40 to +85 3 380 0.5 Negative LDO 3-pin SOT-23A TC57 8 TC59 -10 2.5, 3.0, 3.3 -3.0, -5.0 Note 1: Depending on external transistor configuration. POWER MANAGEMENT - Low-Dropout Regulator Combination Products 300 -40 to +125 80 210 0.5 Shutdown, Reference bypass input, LDO plus Reset output 8-pin MSOP LDO1: 1.5-3.3 LDO2: 1.5-3.3 LDO1: 300 LDO2: 150 -40 to +125 103 LDO1: 104 LDO2: 150 0.5 Dual LDO plus Reset output, Shutdown, Reference bypass, Voltage detect 8-pin MSOP, 8-pin 3x3 DFN 6.0 LDO1: 1.5-3.3 LDO2: 1.5-3.3 LDO1: 300 LDO2: 150 -40 to +125 114 LDO1: 104 LDO2: 150 0.5 Dual LDO plus Reset, per channel output shutdown, Reference bypass 8-pin MSOP, 8-pin 3x3 DFN TC1302A(1) 6.0 LDO1: 1.5-3.3 LDO2: 1.5-3.3 LDO1: 300 LDO2: 150 -40 to +125 103 LDO1: 104 LDO2: 150 0.5 Dual LDO, Output shutdown reference bypass, Voltage detect 8-pin MSOP, 8-pin 3x3 DFN TC1302B(1) 6.0 LDO1: 1.5-3.3 LDO2: 1.5-3.3 LDO1: 300 LDO2: 150 -40 to +125 114 LDO1: 104 LDO2: 150 0.5 Dual LDO, per channel output shutdown, Reference bypass 8-pin MSOP, 8-pin 3x3 DFN TC1305 6.0 2.5, 2.8, 3.0 150(1) -40 to +125 120 240 0.5 Dual LDO plus Reset output, Reference bypass input, Shutdown, Select ModeTM selectable output voltages 10-pin MSOP TC1306 6.0 1.8, 2.8, 3.0 150(1) -40 to +125 120 240 0.5 Dual LDO plus Reset output, Shutdown, Select ModeTM selectable output voltages 8-pin MSOP TC1307(1) 6.0 1.8, 2.5, 2.8, 3.0 150(1) -40 to +125 220 200 0.5 Quad LDO plus Reset output, Shutdown, Select ModeTM selectable output voltage 16-pin QSOP TC1300(1) 6.0 2.5, 2.7, 2.8, 2.85, 3.0, 3.3 TC1301A(1) 6.0 TC1301B(1) Note 1: LDOs with shutdown (except Power Management Combination Products as indicated) have typical shutdown currents of 0.05 mA. Analog and Interface Product Selector Guide 8 POWER MANAGEMENT - Switching Regulators Part # MCP1601 Description Synchronous Buck Regulator Input Voltage Range (V) Output Voltage (V) Operating Temperature Range (C) Control Scheme Switching Frequency (kHz) Typical Active Current (A) Output Current (mA) 2.7 to 5.5 0.9V to VIN -40 to +85 PFM/PWM/LDO 750 825 (PWM) 125 (PFM) 500 UVLO, Auto-switching, LDO 8-pin MSOP 10-pin MSOP, 10-pin 3x3 DFN 5-pin TSOT-23, 8-pin 2x3 DFN 8-pin MSOP, 8-pin 3x3 DFN 6-pin SOT-23, 8-pin 2x3 DFN Features Packages MCP1602 Synchronous Buck Regulator 2.7 to 5.5 0.8 to 4.5 -40 to +85 PFM/PWM 2000 35 500 PFM, PWM auto-switching, UVLO, Soft start, Power good indicator MCP1603 Synchronous Buck Regulator 2.7 to 5.5 0.8 to 4.0 -40 to +85 PFM/PWM 2000 45 500 Overtemperature and Overcurrent protection MCP1612 Synchronous Buck Regulator 2.7 to VIN 0.8 to 5.5 -40 to +85 1400 10,000 1000 MCP1623/4 Step-up DC/DC Regulator 0.65 to 6 2.0 to 5.5 -40 to +85 Constant frequency, PWM PWM or PWM/PFM 500 19 175 MCP1640/B/ C/D Step-up DC/DC Regulator 0.65 to 6 2.0 to 5.5 -40 to +85 PWM or PWM/PFM 500 19 350 MCP1650 Step-up DC/DC Controller 2.7 to 5.5 -40 to +125 Constant frequency, 750 120 560/440 MCP1651 Step-up DC/DC Controller 2.7 to 5.5 -40 to +125 120 560/440 Step-up DC/DC Controller 2.7 to 5.5 -40 to +125 Constant frequency, 2 fixed DC Constant frequency, 2 fixed DC 750 MCP1652 2.5 to ext. tx limited 2.5 to ext. tx limited 2.5 to ext. tx limited 750 120 560/440 MCP1653 Step-up DC/DC Controller 2.7 to 5.5 2.5 to ext. tx limited -40 to +125 Constant frequency, 2 fixed DC 750 120 560/440 MCP16301 30V Input Buck Regulator 4.0 to 30 2.0 to 15 -40 to +85 PWM 500 2000 600 Overall efficiency >94%, Soft start, Overtemperature and Overcurrent protection Integrated synchronous boost regulator, 0.65V start-up voltage, Soft start, True load disconnect Integrated synchronous boost regulator, 0.65V start-up voltage, Soft start, True load disconnect or input-to-output bypass option 2 duty cycles for min. and max. loads, Shutdown control, UVLO, Soft start 2 duty cycles for min. and max. loads, Shutdown control, low battery detect, UVLO, Soft start 2 duty cycles for min. and max. loads, Shutdown control, Power good indicator, UVLO, Soft start 2 duty cycles for min. and max. loads, Shutdown control, Low battery detect, Power good indicator, UVLO, Soft start Integrated N-channel, UVLO, Soft start, Overtemperature protection TC105 Step-down DC/DC Controller 2.2 to 10 3.0, 3.3, 5.0 -40 to +85 PFM/PWM 300 57 1,000 TC115 Step-up DC/DC Regulator 0.9 to 10 3.0, 3.3, 5.0 -40 to +85 PFM/PWM 100 80 TC110 Step-up DC/DC Controller 2.0 to 10 3.0, 3.3, 5.0 -40 to +85 PFM/PWM 100/300 -40 to +85 PFM/PWM -40 to +85 -40 to +85 6-pin SOT-23, 8-pin 2x3 DFN 8-pin MSOP 8-pin MSOP 8-pin MSOP 10-pin MSOP SOT23-6 Low power shutdown mod 5-pin SOT-23A 140 Feedback voltage sensing, Low power shutdown mode 5-pin SOT-89 50/120 300 Soft start, Low power shutdown mode 5-pin SOT-23A 2000 65/600 PFM/PWM auto-switching, Power good output PFM/PWM 2000 65/600 PFM/PWM 2000 65/600 DC/DC: 500 mA LDO: 300 mA DC/DC: 500 mA LDO: 300 mA DC/DC: 500 mA LDO: 300 mA 10-pin MSOP, 10-pin 3x3 DFN 10-pin MSOP, 10-pin 3x3 DFN 10-pin MSOP, 10-pin 3x3 DFN POWER MANAGEMENT - Switching Regulator Combination Products TC1303 TC1304 TC1313 Synchronous Buck Regulator, LDO w/Power good Synchronous Buck Regulator, LDO Synchronous Buck Regulator, LDO 2.7 to 5.5 2.7 to 5.5 2.7 to 5.5 DC/DC: 0.8 to 4.5 LDO: 1.5 to 3.3 DC/DC: 0.8 to 4.5 LDO: 1.5 to 3.3 DC/DC: 0.8 to 4.5 LDO: 1.5 to 3.3 PFM/PWM auto-switching, Power sequencing PFM/PWM auto-switching POWER MANAGEMENT - PWM Controllers Part # MCP1630 MCP1630V MCP1631 MCP1631HV MCP1631V MCP1631VHV Description Current mode, high-speed PWM to use with PIC(R) MCUs Voltage mode, high-speed PWM to use with PIC(R) MCUs Current mode, high-speed PWM to use with PIC(R) MCUs Current mode, high-speed PWM to use with PIC(R) MCUs Voltage mode, high-speed PWM to use with PIC(R) MCUs Voltage mode, high-speed PWM to use with PIC(R) MCUs Input Voltage Range (V) Operating Temperature Range (C) Switching Frequency (kHz) Typical Active Current (mA) 3.0 to 5.5 -40 to +125 1000 2.8 3.0 to 5.5 -40 to +125 1000 2.8 3.0 to 5.5 -40 to +125 2000 3.7 3.5 to 16 -40 to +125 2000 3.7 3.0 to 5.5 -40 to +125 2000 3.7 3.5 to 16 -40 to +125 2000 3.7 Features Packages UVLO, Short circuit and Overtemperature protection, Integrated MOSFET driver UVLO, Short circuit and Overtemperature protection, Integrated MOSFET driver UVLO, Integrated error, current and voltage sense amplifiers, Overvoltage comparator and MOSFET driver Integrated 16V LDO, UVLO, Integrated error, Ccurrent and voltage sense amplifiers, Overvoltage comparator and MOSFET driver UVLO, Integrated error, Current and voltage sense amplifiers, Overvoltage comparator and MOSFET driver Integrated 16V LDO, UVLO, Integrated error, Current and voltage sense amplifiers, Overvoltage comparator and MOSFET driver 8-pin MSOP, 8-pin 2x3 DFN 8-pin MSOP, 8-pin 2x3 DFN 20-pin SSOP, 20-pin TSSOP, 20-pin 4x4 QFN 20-pin SSOP, 20-pin TSSOP 20-pin SSOP, 20-pin TSSOP, 20-pin 4x4 QFN 20-pin SSOP, 20-pin TSSOP Analog and Interface Product Selector Guide 9 POWER MANAGEMENT - Charge Pump DC-to-DC Converters Input Voltage Range (V) Part # Output Voltage (V) Operating Temperature Range (C) Maximum Input Current(1) (A) Typical Active Output Current (mA) Features Packages Inverting or Doubling Charge Pumps TC1044S 1.5 to 12 VOUT = -VIN or VOUT = 2 VIN -40 to +85 160 20 85 kHz oscillator, Boost mode 8-pin PDIP, 8-pin SOIC TC7660 1.5 to 10 VOUT = -VIN or VOUT = 2 VIN -40 to +85 180 20 10 kHz oscillator 8-pin PDIP, 8-pin SOIC TC7660H 1.5 to 10 VOUT = -VIN or VOUT = 2 VIN -40 to +85 1,000 20 120 kHz oscillator 8-pin PDIP, 8-pin SOIC TC7660S 1.5 to 12 VOUT = -VIN or VOUT = 2 VIN -40 to +85 160 20 45 kHz oscillator, Boost mode 8-pin PDIP, 8-pin SOIC TC7662B 1.5 to 15 VOUT = -VIN or VOUT = 2 VIN -40 to +85 180 20 35 kHz oscillator, Boost mode 8-pin PDIP, 8-pin SOIC TC1240 2.5 to 4.0 VOUT = 2 VIN -40 to +85 900 40 Shutdown, 160 kHz oscillator 6-pin SOT-23A TC1240A 2.5 to 5.5 VOUT = 2 VIN -40 to +85 900 40 Shutdown, 160 kHz oscillator 6-pin SOT-23A TC7662A 3.0 to 18 VOUT = -VIN or VOUT = 2 VIN -40 to +85 200 40 12 kHz oscillator 8-pin PDIP, 8-pin SOIC TC962 3.0 to 18 VOUT = -VIN or VOUT = 2 VIN -40 to +85 200 80 Selectable 12 kHz or 24 kHz oscillator 8-pin PDIP, 16-pin SOIC VOUT = -2 VIN -40 to +85 400 10 12 kHz oscillator 8-pin PDIP, 8-pin SOIC Selectable 3.3V or 5.0V or Adjustable 1.5V to 5.5V Selectable 3.3V or 5.0V or Adjustable 1.5V to 5.5V -40 to +85 120 120 mA for VIN>3.0V Power good output, 650 kHz oscillator 8-pin MSOP -40 to +85 120 120 mA for VIN>3.0V Power good output, 1 MHz oscillator 8-pin MSOP Inverting and Doubling Charge Pumps TC682 2.4 to 5.5 Regulated Charge Pumps 2.1/2.7 to 5.5 2.0 to 5.5 2.1/2.7 to 5.5 2.0 to 5.5 MCP1252 MCP1253 MCP1256 1.8 to 3.6 3.3 -40 to +85 100 100 Power good, Sleep mode 10-pin MSOP, 10-pin 3x3 DFN MCP1257 1.8 to 3.6 3.3 -40 to +85 100 100 Sleep mode, Low battery indication 10-pin MSOP, 10-pin 3x3 DFN MCP1258 1.8 to 3.6 3.3 -40 to +85 100 100 Power good output, Input/output bypass 10-pin MSOP, 10-pin 3x3 DFN MCP1259 1.8 to 3.6 3.3 -40 to +85 100 100 Low battery indication, Input/output bypass 10-pin MSOP, 10-pin 3x3 DFN Note 1: Measured at VDD = 5.0V at 25C and no load. POWER MANAGEMENT - CPU/System Supervisors MCP102 1.0 to 5.5 Operating Temperature Range (C) -40 to +125 4.63, 4.38, 3.08, 2.93, 2.63, 2.32, 1.9 Active-Low CMOS Push-Pull Typical Reset Pulse Width (ms) 120 MCP103 1.0 to 5.5 -40 to +125 4.63, 4.38, 3.08, 2.93, 2.63, 2.32, 1.9 Active-Low CMOS Push-Pull 120 1 MCP121 1.0 to 5.5 -40 to +125 4.63, 4.38, 3.08, 2.93, 2.63, 2.32, 1.9 Active-Low Open-Drain 120 1 Part # MCP131 MCP1319 Vcc Range (V) 1.0 to 5.5 1.0 to 5.5 -40 to +125 -40 to +125 Nominal Reset Voltage (V) 4.63, 4.38, 3.08, 2.93, 2.63, 2.32, 1.9 (1) 4.6, 2.9 Reset Type Output Typical Supply Current (A) 1 Bond Options Additional Features Packages 3-pin SOT-23B, 3-pin SC-70, 3-pin TO-92 N/A Max. 809 Pinout 3-pin SOT-23B, 3-pin SC-70, 3-pin TO-92 N/A 3-pin SOT-23B, 3-pin SC-70, 3-pin TO-92 N/A 3-pin SOT-23B, 3-pin SC-70, 3-pin TO-92 N/A 100 k Internal Pull-up Resistor Active-Low Open-Drain 120 1 Active-Low/High CMOS Push-Pull 200 1 Manual Reset 5-pin SOT-23 N/A Manual Reset, two Reset outputs (Active-Low Open-Drain, Active-High Push-Pull) 5-pin SOT-23 N/A 5-pin SOT-23 N/A 5-pin SOT-23 N/A 5-pin SOT-23 N/A MCP1322 1.0 to 5.5 -40 to +125 4.6, 2.9(1) Active-High Open-Drain/CMOS Push-Pull 200 1 MCP1316 1.0 to 5.5 -40 to +125 4.6, 2.9(1) Active-Low CMOS Push-Pull 200 5 MCP1317 1.0 to 5.5 -40 to +125 4.6, 2.9(1) Active-High CMOS Push-Pull 200 5 MCP1318 1.0 to 5.5 -40 to +125 4.6, 2.9(1) Active-Low/High CMOS Push-Pull 200 5 Watchdog Input (WDI), Time-out = 1.6 sec., Manual Reset Watchdog Input (WDI), Time-out = 1.6 sec., Manual Reset Watchdog Input (WDI), Time-out = 1.6 sec. Note 1: Other reset voltage options available: 2.0V to 4.7V in 100 mV increments. Contact local Microchip sales office. Analog and Interface Product Selector Guide 10 POWER MANAGEMENT - CPU/System Supervisors (Continued) Part # MCP1320 MCP1321 Vcc Range (V) Operating Temperature Range (C) 1.0 to 5.5 -40 to +125 4.6, 2.9(1) -40 to +125 (1) 1.0 to 5.5 Nominal Reset Voltage (V) 4.6, 2.9 Reset Type Output Typical Reset Pulse Width (ms) Typical Supply Current (A) Additional Features Active-Low Open-Drain 200 5 Watchdog Input (WDI), Time-out = 1.6 sec., Manual Reset 5-pin SOT-23 N/A Active-Low Open-Drain/CMOS Push-Pull 5 Watchdog Input (WDI), Time-out = 1.6 sec., Manual Reset (Active-Low Open-Drain, Active-High Push-Pull) 5-pin SOT-23 N/A 200 Packages Bond Options TC1270A 1.0 to 5.5 -40 to +125 4.63, 4.38, 3.08, 2.93, 2.63 Active-Low CMOS Push-Pull 280 7 Manual Reset 4-pin SOT-143, 5-pin SOT-23 N/A TC1271A 1.0 to 5.5 -40 to +125 4.63, 4.38, 3.08, 2.93, 2.63 Active-High CMOS Push-Pull 280 7 Manual Reset 4-pin SOT-143, 5-pin SOT-23 N/A Manual Reset TC1270AN 1.0 to 5.5 -40 to +125 4.63, 4.38, 3.08, 2.93, 2.63 Active-Low Open-Drain 0 7 4-pin SOT-143, 5-pin SOT-23 N/A TCM809 1.2 to 5.5 -40 to +85 4.63, 4.38, 4.00, 3.08, 2.93, 2.63, 2.32 Active-Low CMOS Push-Pull 240 12 3-pin SOT-23B, 3-pin SC-70 N/A TCM810 1.2 to 5.5 -40 to +85 4.63, 4.38, 4.00, 3.08, 2.93, 2.63, 2.32 Active-High CMOS Push-Pull 240 12 3-pin SOT-23B, 3-pin SC-70 N/A MCP100 1.0 to 5.5 -40 to +85 4.72, 4.62, 4.47, 4.37, 3.075, 2.92, 2.62 Active-Low CMOS Push-Pull 350 45 3-pin TO-92, 3-pin SOT-23B D, H MCP809 1.0 to 5.5 -40 to +85 4.72, 4.62, 4.47, 4.37, 3.075, 2.92, 2.62 Active-Low CMOS Push-Pull 350 45 3-pin SOT-23B N/A MCP101 1.0 to 5.5 -40 to +85 4.72, 4.62, 4.47, 4.37, 3.075, 2.92, 2.62 Active-High CMOS Push-Pull 350 45 3-pin TO-92, 3-pin SOT-23B D, H MCP810 1.0 to 5.5 -40 to +85 4.72, 4.62, 4.47, 4.37, 3.075, 2.92, 2.62 Active-High CMOS Push-Pull 350 45 3-pin SOT-23B MCP120 1.0 to 5.5 -40 to +85 4.72, 4.62, 4.47, 4.37, 3.075, 2.92, 2.62 Active-Low Open-Drain 350 45 MCP130 1.0 to 5.5 -40 to +85 4.72, 4.62, 4.47, 4.37, 3.075, 2.92, 2.62 Active-Low Open-Drain w/5 kOhm Pull-up 350 45 TC1232 4.5 to 5.5 -40 to +85 4.62, 4.37 Active-Low/High Open-Drain 610 50 Watchdog Timer 3-pin TO-92, 3-pin SOT-23, 8-pin SOIC 3-pin TO-92, 3-pin SOT-23, 8-pin SOIC 8-pin PDIP, 8-pin SOIC, 16-pin SOIC TC32M 4.5 to 5.5 -40 to +85 4.5 Active-Low Open-Drain 700 50 Watchdog Timer 3-pin TO-92, 3-pin SOT-223 N/A D, G, H D, F, H N/A N/A Note 1: Other reset voltage options available: 2.0V to 4.7V in 100 mV increments. Contact local Microchip sales office. POWER MANAGEMENT - Voltage Detectors MCP111 1.0 to 5.5 Operating Temperature Range (C) -40 to +125 4.63, 4.38, 3.08, 2.93, 2.63, 2.32, 1.90 Active-Low Open-Drain Minimum Reset Pulse Width (ms) - MCP112 1.0 to 5.5 -40 to +125 4.63, 4.38, 3.08, 2.93, 2.63, 2.32, 1.90 Active-Low CMOS Push-Pull - 1 TC52 1.5 to 10 -40 to +85 4.5/2.7, 3.0/2.7 Active-Low Open-Drain - 2 TC54 0.7 to 10 -40 to +85 4.3, 4.2, 3.0, 2.9, 2.7, 2.1, 1.4 Active-Low CMOS Push-Pull or Open-Drain - 1 Part # Vcc Range (V) Nominal Reset Voltage (V) Reset Type Output Typical Supply Current (A) 1 Features Packages 3-pin SOT-23B, 3-pin TO-92, 3-pin SC-70, 3-pin SOT-89 3-pin SOT-23B, 3-pin TO-92, 3-pin SC-70, 3-pin SOT-89 Dual channel 5-pin SOT-23A 3-pin SOT-23A, 3-pin SOT-89, 3-pin TO-92 Analog and Interface Product Selector Guide 11 POWER MANAGEMENT - Power MOSFET Drivers Part # Configuration Operating Temperature Range (C) Peak Output Current (A) Output Resistance (RH/RL) (Max. @ 25C) Maximum Supply Voltage (V) Input/Output Delay (tD1, tD2)(1) (ns) Packages Low-Side Drivers, 0.5A to 1.2A Peak Output Current MCP1401 Single, Inverting -40 to +125 0.5 18/16 18 40/40 5-pin SOT-23 MCP1402 Single, Non-inverting -40 to +125 0.5 18/16 18 40/40 5-pin SOT-23 TC1410 Single, Inverting -40 to +85 0.5 22/22 16 30/30 8-pin PDIP, 8-pin SOIC, 8-pin MSOP 8-pin PDIP, 8-pin SOIC, 8-pin MSOP TC1410N Single, Non-inverting -40 to +85 0.5 22/22 16 30/30 TC1411 Single, Inverting -40 to +85 1.0 11/11 16 30/30 8-pin PDIP, 8-pin SOIC, 8-pin MSOP TC1411N Single, Non-inverting -40 to +85 1.0 11/11 16 30/30 8-pin PDIP, 8-pin SOIC, 8-pin MSOP TC1426 Dual, Inverting 0 to +70 1.2 18/18 16 75/75 8-pin PDIP, 8-pin SOIC TC1427 Dual, Non-inverting 0 to +70 1.2 18/18 16 75/75 8-pin PDIP, 8-pin SOIC TC1428 Dual, Inverting and Non-inverting 0 to +70 1.2 18/18 16 75/75 8-pin PDIP, 8-pin SOIC TC4467 Quad, Inverting -40 to +85 1.2 15/15 18 40/40 14-pin PDIP, 16-pin SOIC (W) TC4468 Quad, Non-inverting -40 to +85 1.2 15/15 18 40/40 14-pin PDIP, 16-pin SOIC (W) TC4469 Quad, Non-inverting -40 to +85 1.2 15/15 18 40/40 14-pin PDIP, 16-pin SOIC (W) Low-Side Drivers, 1.5A Peak Output Current MCP1415 Single, Inverting -40 to +125 1.5 7.5/5.5 18 50/55 5-pin SOT-23 MCP1416 Single, Non-inverting -40 to +125 1.5 7.5/5.5 18 50/55 5-pin SOT-23 TC4403 Single, Non-inverting Floating Load Driver -40 to +85 1.5 5/5 18 33/38 8-pin PDIP TC4404 Dual, Inverting -40 to +85 1.5 10/10 18 15/32 8-pin PDIP, 8-pin SOIC TC4405 Dual, Non-inverting -40 to +85 1.5 10/10 18 15/32 8-pin PDIP, 8-pin SOIC TC4426A Dual, Inverting -40 to +125 1.5 9/9 18 30/30 8-pin PDIP, 8-pin SOIC, 8-pin DFN TC4427A Dual, Non-inverting -40 to +125 1.5 9/9 18 30/30 8-pin PDIP, 8-pin SOIC, 8-pin DFN TC4428A Dual, Inverting and Non-inverting -40 to +125 1.5 9/9 18 30/30 8-pin PDIP, 8-pin SOIC, 8-pin DFN TC4426 Dual, Inverting -40 to +125 1.5 10/10 18 20/40 8-pin PDIP, 8-pin SOIC, 8-pin DFN, 8-pin MSOP TC4427 Dual, Non-inverting -40 to +125 1.5 10/10 18 20/40 8-pin PDIP, 8-pin SOIC, 8-pin DFN, 8-pin MSOP TC4428 Dual, Inverting and Non-inverting -40 to +125 1.5 10/10 18 20/40 8-pin PDIP, 8-pin SOIC, 8-pin DFN, 8-pin MSOP TC426 Dual, Inverting -40 to +85 1.5 15/10 18 50/75 8-pin PDIP, 8-pin SOIC TC427 Dual, Non-inverting -40 to +85 1.5 15/10 18 50/75 8-pin PDIP, 8-pin SOIC TC428 Dual, Inverting and Non-inverting -40 to +85 1.5 15/10 18 50/75 8-pin PDIP, 8-pin SOIC TC1412 Single, Inverting -40 to +85 2 6/6 16 35/35 8-pin PDIP, 8-pin SOIC, 8-pin MSOP TC1412N Single, Non-inverting -40 to +85 2 6/6 16 35/35 8-pin PDIP, 8-pin SOIC, 8-pin MSOP MCP14E6 Dual, Inverting -40 to +125 2 2.2/2.8 18 45/45 8-pin PDIP, 8-pin SOIC, 8-pin DFN MCP14E7 Dual, Non-inverting -40 to +125 2 2.2/2.8 18 45/45 8-pin PDIP, 8-pin SOIC, 8-pin DFN MCP14E8 Dual, Inverting and Non-inverting -40 to +125 2 2.2/2.8 18 45/45 8-pin PDIP, 8-pin SOIC, 8-pin DFN MCP14E9 Dual, Inverting -40 to +125 3 2.2/2.8 18 75/75 8-pin PDIP, 8-pin SOIC, 8-pin DFN MCP14E10 Dual, Non-inverting -40 to +125 3 2.2/2.8 18 75/75 8-pin PDIP, 8-pin SOIC, 8-pin DFN MCP14E11 Dual, Inverting and Non-inverting -40 to +125 3 2.2/2.8 18 75/75 8-pin PDIP, 8-pin SOIC, 8-pin DFN Note 1: tD1 = delay time from input low-to-high transition to output transition. tD2 = delay time from input high-to-low transition to output transition. Analog and Interface Product Selector Guide 12 POWER MANAGEMENT - Power MOSFET Drivers (Continued) Part # Configuration Operating Temperature Range (C) Peak Output Current (A) Output Resistance (RH/RL) (Max. @ 25C) Maximum Supply Voltage (V) Input/Output Delay (tD1, tD2)(1) (ns) -40 to +85 3 4/4 16 35/35 8-pin PDIP, 8-pin SOIC, 8-pin MSOP 8-pin PDIP, 8-pin SOIC, 8-pin MSOP Packages Low-Side Drivers, 2.0A to 12.0A Peak Output Current TC1413 Single, Inverting TC1413N Single, Non-inverting -40 to +85 3 4/4 16 35/35 TC4423A Dual, Inverting -40 to +125 3 3 (typ)/4 (typ) 18 40 (typ)/40 (typ) 8-pin PDIP, 8-pin SOIC, 8-pin DFN TC4424A Dual, Non-inverting -40 to +125 3 3 (typ)/4 (typ) 18 40 (typ)/40 (typ) 8-pin PDIP, 8-pin SOIC, 8-pin DFN TC4425A Dual, Inverting and Non-inverting -40 to +125 3 3 (typ)/4 (typ) 18 40 (typ)/40 (typ) 8-pin PDIP, 8-pin SOIC, 8-pin DFN TC4423 Dual, Inverting -40 to +125 3 5/5 18 33/38 8-pin PDIP, 16-pin SOIC (W), 8-pin DFN TC4424 Dual, Non-inverting -40 to +125 3 5/5 18 33/38 8-pin PDIP, 16-pin SOIC (W), 8-pin DFN TC4425 Dual, Inverting and Non-inverting -40 to +125 3 5/5 18 33/38 8-pin PDIP, 16-pin SOIC (W), 8-pin DFN MCP14E3 Dual, Inverting -40 to +125 4.0 3.5/3.0 18 55/55 8-pin PDIP, 8-pin SOIC, 8-pin 6x5 DFN MCP14E4 Dual, Non-inverting -40 to +125 4.0 3.5/3.0 18 55/55 8-pin PDIP, 8-pin SOIC, 8-pin 6x5 DFN MCP14E5 Dual, Inverting and Non-inverting -40 to +125 4.0 3.5/3.0 18 55/55 8-pin PDIP, 8-pin SOIC, 8-pin 6x5 DFN MCP1403 Dual, Inverting -40 to +125 4.5 3/3.5 18 48/48 8-pin PDIP, 8-pin SOIC, 8-pin 6x5 DFN, 16-pin SOIC MCP1404 Dual, Non-inverting -40 to +125 4.5 3/3.5 18 48/48 8-pin PDIP, 8-pin SOIC, 8-pin 6x5 DFN, 16-pin SOIC MCP1405 Dual, Inverting and Non-inverting -40 to +125 4.5 3/3.5 18 48/48 8-pin PDIP, 8-pin SOIC, 8-pin 6x5 DFN, 16-pin SOIC MCP1406 Single, Inverting -40 to +125 6 1.8 (typ)/2.0 (typ) 18 30/30 5-pin TO-220, 8-pin PDIP, 8-pin 6x5 DFN, 8-pin SOIC MCP1407 Single, Non-inverting -40 to +125 6 1.8 (typ)/2.0 (typ) 18 30/30 5-pin TO-220, 8-pin PDIP, 8-pin 6x5 DFN, 8-pin SOIC TC429 Single, Inverting -40 to +85 6 2.5/2.5 18 53/60 8-pin PDIP, 8-pin DFN, 8-pin SOIC TC4420 Single, Non-inverting -40 to +125 6 2.8/2.5 18 55/55 8-pin PDIP, 8-pin SOIC, 5-pin TO-220, 8-pin DFN TC4429 Single, Inverting -40 to +125 6 2.8/2.5 18 55/55 8-pin PDIP, 8-pin SOIC, 5-pin TO-220, 8-pin DFN TC4421 Single, Inverting -40 to +125 9 1.4 (typ)/1.7 18 30/33 8-pin PDIP, 5-pin TO-220, 8-pin DFN TC4421A Single, Inverting -40 to +125 9 1.25 (typ)/1.5 18 38/42 8-pin PDIP, 8-pin SOIC, 5-pin TO-220, 8-pin 6x5 DFN TC4422 Single, Non-inverting -40 to +125 9 1.4 (typ)/1.7 18 30/33 8-pin PDIP, 5-pin TO-220, 8-pin DFN TC4422A Single, Non-inverting -40 to +125 9 1.25 (typ)/1.5 18 38/42 8-pin PDIP, 8-pin SOIC, 5-pin TO-220, 8-pin 6x5 DFN TC4451 Single, Inverting -40 to +125 12 0.6 (typ)/1.5 18 15/15 8-pin SOIC, 8-pin PDIP, 8-pin 6x5 DFN, 5-pin TO-220, 5-pin DDPAK TC4452 Single, Non-inverting -40 to +125 12 0.6 (typ)/1.5 18 15/15 8-pin SOIC, 8-pin PDIP, 8-pin 6x5 DFN, 5-pin TO-220, 5-pin DDPAK High-Side/Low-Side Drivers TC4626 Single, Inverting -40 to +85 1.5 15/10 6 35/45 8-pin PDIP, 16-pin SOIC (W) TC4627 Single, Non-inverting -40 to +85 1.5 15/10 6 35/45 8-pin PDIP, 16-pin SOIC (W) TC4431 Single, Inverting -40 to +85 1.5 10/10 30 62/78 8-pin PDIP, 8-pin SOIC TC4432 Single, Non-inverting -40 to +85 1.5 10/10 30 62/78 8-pin PDIP, 8-pin SOIC Synchronous Buck High-Side Drivers MCP14628 Dual, Non-inverting -40 to +85 2 2.5/2.5 5 (VDD), 36 (Boot Pin) 18/20 8-pin SOIC, 8-pin 3x3 DFN MCP14700 Dual, Non-inverting -40 to +125 2 2.5/2.5 5 (VDD), 36 (Boot Pin) 25/25 8-pin SOIC, 8-pin 3x3 DFN Note 1: tD1 = delay time from input low-to-high transition to output transition. tD2 = delay time from input high-to-low transition to output transition. Analog and Interface Product Selector Guide 13 POWER MANAGEMENT - Battery Chargers Part # Mode Cell Type # of Cells Vcc Range (V) Cell Voltage (V) Maximum Charging Current (mA) Max. Voltage Regulation (%) Int/Ext FET MCP73113 Linear Li-ion/Li-Polymer 1 4 to 16 4.1, 4.2, 4.35, 4.4 1100 0.5 Int 6.5V Overvoltage Protection 10-pin 3x3 DFN MCP73114 Linear Li-ion/Li-Polymer 1 4 to 16 4.1, 4.2, 4.35, 4.4 1100 0.5 Int 5.8V Overvoltage Protection 10-pin 3x3 DFN MCP73123 Linear LiFePO4 1 4 to 16 3.6 1100 0.5 Int 6.5V Overvoltage Protection, LiFePO4 charging 10-pin 3x3 DFN MCP73213 Linear Li-ion/Li-Polymer 2 4 to 16 8.2, 8.4, 8.7, 8.8 1100 0.6 Int 13V Overvoltage Protection 10-pin 3x3 DFN MCP73223 Linear LiFePO4 2 4 to 16 7.2 1100 0.6 Int 13V Overvoltage Protection, LiFePO4 charging 10-pin 3x3 DFN MCP73826 Linear Li-Ion/Li-Polymer 1 4.5 to 5.5 4.1, 4.2 N/A 1.0 Ext Small size, charge current set by external FET 6-pin SOT-23 Ext Mode indicator, Charge current monitor, Charge current set by external FET 8-pin MSOP MCP73827 Linear Li-Ion/Li-Polymer 1 4.5 to 5.5 4.1, 4.2 N/A 1.0 Features Packages MCP73828 Linear Li-Ion/Li Polymer 1 4.5 to 5.5 4.1, 4.2 N/A 1.0 Ext Temperature monitor, Charge current set by external FET 8-pin MSOP MCP73841 Linear Li-Ion/Li-Polymer 1 4.5 to 12 4.1, 4.2 N/A 0.5 Ext 10-pin MSOP 10-pin MSOP 8-pin MSOP MCP73842 Linear Li-Ion/Li-Polymer 2 8.7 to 12 8.2, 8.4 N/A 0.5 Ext Safety charge timers, Temperature monitor, Charge current set by external FET Safety charge timers, Temperature monitor, Charge current set by external FET MCP73843 Linear Li-Ion/Li-Polymer 1 4.5 to 12 4.1, 4.2 N/A 0.5 Ext Safety charge timers, Charge current set by external FET MCP73844 Linear Li-Ion/Li-Polymer 2 8.7 to 12 8.2, 8.4 N/A 0.5 Ext Safety charge timers, Charge current set by external FET 8-pin MSOP MCP73811 Linear Li-Ion/Li-Polymer 1 3.7 to 6.0 4.2 500 1.0 Int Selectable charge current (100 mA, 500 mA), Charge enable input 5-pin SOT-23 MCP73812 Linear Li-Ion/Li Polymer 1 3.7 to 6.0 4.2 500 1.0 Int Programmable charge current (100 mA, 500 mA), Charge enable input 5-pin SOT-23 MCP73831 Linear Li-Ion/Li-Polymer 1 3.7 to 6.0 4.2, 4.35, 4.4, 4.5 500 0.75 Int UVLO, Thermal regulation, Programmable charge current, Tri-state STAT pin 5-pin SOT-23, 8-pin 2x3 DFN MCP73832 Linear Li-Ion/Li-Polymer 1 3.7 to 6.0 4.2, 4.35, 4.4, 4.5 500 0.75 Int UVLO, Thermal regulation, Programmable charge current, Open-drain STAT pin 5-pin SOT-23, 8-pin 2x3 DFN MCP73853 Linear Li-Ion/Li-Polymer 1 4.5 to 5.5 4.1, 4.2 500 0.5 Int USB control, Safety charge timers, Temperature monitor, Thermal regulation 16-pin 4x4 QFN MCP73855 Linear Li-Ion/Li-Polymer 1 4.5 to 5.5 4.1, 4.2 500 0.5 Int USB control, Safety charge timers, Thermal regulation 10-pin 3x3 DFN 10-pin 3x3 DFN, 10-pin MSOP MCP73833 Linear Li-Ion/Li-Polymer 1 3.7 to 6.0 4.2, 4.35, 4.4, 4.5 1000 0.75 Int UVLO, Thermal regulation, Thermistor input, LDO Test mode, Multiple VREG outputs, Safety timer, Power good output MCP73834 Linear Li-Ion/Li-Polymer 1 3.7 to 6.0 4.2, 4.35, 4.4, 4.5 1000 0.75 Int UVLO, Thermal regulation, Thermistor input, LDO Test mode, Multiple VREG outputs, Safety timer, Timer enable input 10-pin 3x3 DFN, 10-pin MSOP MCP73837 Linear Li-Ion/Li-Polymer 1 3.7 to 6.0 4.2, 4.35, 4.4, 4.5 1000 0.75 Int Dual input (USB, DC input from adapter) auto-switching, UVLO, Thermal regulation, Thermistor input, Power good output 10-pin 3x3 DFN, 10-pin MSOP MCP73838 Linear Li-Ion/Li Polymer 1 3.7 to 6.0 4.2, 4.35, 4.4, 4.5 1000 0.75 Int Dual input (USB, DC input from adapter) auto-switching, UVLO, Thermal regulation, Timer enable input 10-pin 3x3 DFN, 10-pin MSOP MCP73861 Linear Li-Ion/Li-Polymer 1 4.5 to 12 4.1, 4.2 1000 0.5 Int Safety charge timers, Temperature monitor, Thermal regulation, Flashing STAT1 output on charge complete 16-pin 4x4 QFN, 16-pin SOIC MCP73862 Linear Li-Ion/Li-Polymer 2 8.7 to 12 8.2, 8.4 1000 0.5 Int Safety charge timers, Temperature monitor, Thermal regulation, hi-Z STAT1 output on charge complete 16-pin 4x4 QFN, 16-pin SOIC MCP73863 Linear Li-Ion/Li-Polymer 1 4.5 to 12 4.1, 4.2 1000 0.5 Int Safety charge timers, Temperature monitor, Thermal regulation, hi-Z STAT1 output on charge complete 16-pin 4x4 QFN, 16-pin SOIC MCP73864 Linear Li-Ion/Li-Polymer 2 8.7 to 12 8.2, 8.4 1000 0.5 Int Safety charge timers, Temperature monitor, Thermal regulation, hi-Z STAT1 output on charge complete 16-pin 4x4 QFN, 16-pin SOIC MCP73871 Linear Li-Ion/Li-Polymer 1 3.75 to 6.0 4.2, 4.35, 4.4 1500 (A/C Adapter) 500 (USB) 0.5 Int Simultaneous charging of load and battery, Load-dependent charging, Multiple programmable charge currents 20-pin 4x4 QFN, 20-pin SSOP POWER MANAGEMENT - Hot Swap Controllers Part # MCP18480 Number of Outputs VPOS to VNEG Differential Voltage (V) Junction Temperature Range (C) OVLO UVLO Power good Int/Ext FET 1 -0.3 to +15.0 -40 to +85 Adjustable Adjustable Adjustable Ext Applications -48V Telecom/Datacom, Bus/Backplane Packages 20-pin SSOP Analog and Interface Product Selector Guide 14 LINEAR LINEAR - Op Amps Part # # per Package GBWP IQ Typical (A) VOS Max (mV) Typical Input Bias Current (pA) Input Voltage Noise Density (nV/rtHz) Operating Voltage (V) Temperature Range (C) Features Packages MCP6441 1 9 kHz 0.45 4.5 1 190(1) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 5-pin SOT-23(S), 5-pin SC-70(S) MCP6442 2 9 kHz 0.45 4.5 1 190(1) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin MSOP, 8-pin 2x3 TDFN MCP6444 4 9 kHz 0.45 4.5 1 190(1) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 14-pin SOIC, 14-pin TSSOP MCP6031 1 10 kHz 0.9 0.15 1 165(1) 1.8 to 5.5 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin MSOP, 8-pin 2x3 DFN, 5-pin SOT-23 MCP6032 2 10 kHz 0.9 0.15 1 165(1) 1.8 to 5.5 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin MSOP (1) MCP6033 1 10 kHz 0.9 0.15 1 165 1.8 to 5.5 -40 to +125 Rail-to-Rail Input/Output, Chip select 8-pin SOIC, 8-pin MSOP, 8-pin 2x3 DFN MCP6034 4 10 kHz 0.9 0.15 1 165(1) 1.8 to 5.5 -40 to +125 Rail-to-Rail Input/Output 14-pin SOIC, 14-pin TSSOP MCP6041 1 14 kHz 0.6 3 1 170(1) 1.4 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 5-pin SOT-23(S) (1) MCP6042 2 14 kHz 0.6 3 1 170 1.4 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin PDIP, 8-pin SOIC, 8-pin MSOP MCP6043 1 14 kHz 0.6 3 1 170(1) 1.4 to 6.0 -40 to +125 Rail-to-Rail Input/Output, Chip select 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 6-pin SOT-23(S) MCP6044 4 14 kHz 0.6 3 1 170(1) 1.4 to 6.0 -40 to +125 Rail-to-Rail Input/Output 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP MCP6141 1 100 kHz 0.6 3 1 170(1) 1.4 to 6.0 -40 to +125 Rail-to-Rail Input/Output, G>10 stable 5-pin SOT-23(S), 8-pin PDIP, 8-pin SOIC, 8-pin MSOP 1 170 (1) 1.4 to 6.0 -40 to +125 Rail-to-Rail Input/Output, G>10 stable 8-pin PDIP, 8-pin SOIC, 8-pin MSOP (1) 1.4 to 6.0 -40 to +125 Rail-to-Rail Input/Output, G>10 stable, Chip select 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 6-pin SOT-23(S), 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP MCP6142 2 100 kHz 0.6 MCP6143 1 100 kHz 0.6 MCP6144 4 100 kHz MCP606 1 155 kHz MCP607 2 MCP608 1 3 3 1 170 0.6 3 1 170(1) 1.4 to 6.0 -40 to +125 Rail-to-Rail Input/Output, G>10 stable 19 0.25 1 38(1) 2.5 to 6.0 -40 to +125 Rail-to-Rail Output 8-pin PDIP, 8-pin SOIC, 8-pin TSSOP, 5-pin SOT23(S) 155 kHz 19 0.25 1 38(1) 2.5 to 6.0 -40 to +85 Rail-to-Rail Output 8-pin PDIP, 8-pin SOIC, 8-pin TSSOP 155 kHz 19 0.25 1 38(1) 2.5 to 6.0 -40 to +85 Rail-to-Rail Output, Chip select 8-pin PDIP, 8-pin SOIC, 8-pin TSSOP (1) MCP609 4 155 kHz 19 0.25 1 2.5 to 6.0 -40 to +85 Rail-to-Rail Output 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP MCP616 1 190 kHz 19 0.15 15000 32(1) 2.3 to 5.5 -40 to +85 Rail-to-Rail Output, PNP input 8-pin PDIP, 8-pin SOIC, 8-pin MSOP MCP617 2 190 kHz 19 0.15 15000 32(1) 2.3 to 5.5 -40 to +85 Rail-to-Rail Output, PNP input 8-pin PDIP, 8-pin SOIC, 8-pin MSOP MCP618 1 190 kHz 19 0.15 15000 32(1) 2.3 to 5.5 -40 to +85 Rail-to-Rail Output, Chip select, PNP input 8-pin PDIP, 8-pin SOIC, 8-pin MSOP MCP619 4 190 kHz 19 0.15 15000 32(1) 2.3 to 5.5 -40 to +85 Rail-to-Rail Output, PNP input 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP MCP6231 1 300 kHz 20 5 1 52(1) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin 2x3 TDFN, 5-pin SC-70(U), 5-pin SOT-23(S,R,U) MCP6232 2 300 kHz 20 5 1 52(1) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin 2x3 TDFN MCP6234 4 300 kHz 20 5 1 52(1) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP MCP6051 1 385 kHz 30 0.15 1 34(2) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin 2x3 DFN, 5-pin SOT-23(S) MCP6052 2 385 kHz 30 0.15 1 34(2) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin 2x3 DFN MCP6054 4 385 kHz 30 0.15 1 34(2) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 14-pin SOIC, 14-pin TSSOP MCP6241 1 550 kHz 50 5 1 45(1) 1.8 to 5.5 -40 to +125 Rail-to-Rail Input/Output 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin 2x3 TDFN, 5-pin SC-70(U), 5-pin SOT-23(S,R,U), MCP6242 2 550 kHz 50 5 1 45(1) 1.8 to 5.5 -40 to +125 Rail-to-Rail Input/Output 8-pin PDIP, 8-pin SOIC, 8-pin MSOP MCP6244 4 550 kHz 50 5 1 45(1) 1.8 to 5.5 -40 to +125 Rail-to-Rail Input/Output 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP MCP6061 1 730 kHz 60 0.15 1 25(2) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin 2x3 DFN, 5-pin SOT-23(S) (2) 38 MCP6062 2 730 kHz 60 0.15 1 25 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin 2x3 DFN MCP6064 4 730 kHz 60 0.15 1 25(2) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 14-pin SOIC, 14-pin TSSOP MCP6001 1 1 MHz 100 4.5 1 28(1) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 5-pin SOT-23(S,R,U), 5-pin SC-70(R) MCP6002 2 1 MHz 100 4.5 1 28(1) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin 2x3 DFN Legend: S = Standard Pinout; R = Reverse Pinout; U = Alternative Pinout Note 1: Values are typical at 1 kHz 2: Values are typical at 10 kHz Analog and Interface Product Selector Guide 15 LINEAR - Op Amps (Continued) Part # # per Package GBWP IQ Typical (A) Vos Max (mV) Typical Input Bias Current (pA) Input Voltage Noise Density (nV/rtHz) Operating Voltage (V) Temperature Range (C) Features Packages MCP6004 4 1 MHz 100 4.5 1 28(1) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP MCP6401 1 1 MHz 45 4.5 1 28(1) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 5-pin SOT-23(S,R,U), 5-pin SC-70(R) MCP6402 2 1 MHz 45 4.5 1 28(1) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin 2x3 TDFN MCP6404 4 1 MHz 45 4.5 1 28(1) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 14-pin SOIC, 14-pin TSSOP 2 24 (2) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 5-pin SOT-23(S,R,U), 5-pin SC-70(S) (2) MCP6L01 1 1 MHz 85 5 MCP6L02 2 1 MHz 85 5 2 24 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin MSOP MCP6L04 4 1 MHz 85 5 2 24(2) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 14-pin SOIC, 14-pin TSSOP MCP6071 1 1.2 MHz 110 0.15 1 19(2) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin 2x3 DFN, 5-pin SOT-23(S) (2) 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin 2x3 DFN 1.8 to 6.0 -40 to +125 Rail-to-Rail Input/Output 14-pin SOIC, 14-pin TSSOP -40 to +125 Rail-to-Rail Output 8-pin SOIC, 8-pin 2x3 TDFN -40 to +125 Rail-to-Rail Output 8-pin SOIC, 8-pin 2x3 TDFN -40 to +125 Rail-to-Rail Output 14-pin SOIC, 14-pin TSSOP 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 5-pin SOT-23(S,R), MCP6072 2 1.2 MHz 110 0.15 1 19 MCP6074 4 1.2 MHz 110 0.15 1 19(2) MCP6H02 2 1.2 MHz 135 3.5 10 35 MCP6H04 4 1.2 MHz 135 3.5 10 35(1) Single Supply: 3.5 to 16 Dual Supply: 1.75 to 8 Single Supply: 3.5 to 16 Dual Supply: 1.75 to 8 Single Supply: 3.5 to 16 Dual Supply: 1.75 to 8 MCP6271 1 2 MHz 170 3 1 20(1) 2.0 to 6.0 -40 to +125 Rail-to-Rail Input/Output MCP6H01 1 1.2 MHz 135 3.5 10 35 (1) (1) MCP6272 2 2 MHz 170 3 1 20(1) 2.0 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin PDIP, 8-pin SOIC, 8-pin MSOP MCP6273 1 2 MHz 170 3 1 20(1) 2.0 to 6.0 -40 to +125 Rail-to-Rail Input/Output, Chip select 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 6-pin SOT-23(S) MCP6274 4 2 MHz 170 3 1 20(1) 2.0 to 6.0 -40 to +125 Rail-to-Rail Input/Output 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP 1 20 (1) 2.0 to 6.0 -40 to +125 Rail-to-Rail Input/Output, Dual connected, Chip select 8-pin PDIP, 8-pin SOIC, 8-pin MSOP 19 (2) 2.0 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC(S), 8-pin MSOP(S), 5-pin SOT-23(S,R) (2) MCP6275 MCP6L71 2 1 2 MHz 2 MHz 150 150 3 4 1 MCP6L72 2 2 MHz 150 4 1 19 2.0 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin MSOP MCP6L74 4 2 MHz 150 4 1 19(2) 2.0 to 6.0 -40 to +125 Rail-to-Rail Input/Output 14-pin SOIC, 14-pin TSSOP MCP601 1 2.8 MHz 230 2 1 29(1) 2.7 to 6.0 -40 to +125 Rail-to-Rail Output 8-pin PDIP, 8-pin SOIC, 8-pin TSSOP, 5-pin SOT-23(S,R) MCP602 2 2.8 MHz 230 2 1 29(1) 2.7 to 6.0 -40 to +125 Rail-to-Rail Output 8-pin PDIP, 8-pin SOIC, 8-pin TSSOP MCP603 1 2.8 MHz 230 2 1 29(1) 2.7 to 6.0 -40 to +125 Rail-to-Rail Output, Chip select 8-pin PDIP, 8-pin SOIC, 8-pin TSSOP, 6-pin SOT-23(S) MCP604 4 2.8 MHz 230 2 1 29(1) 2.7 to 6.0 -40 to +125 Rail-to-Rail Output 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP MCP6L1 1 2.8 MHz 200 3 1 21(2) 2.7 to 6.0 -40 to +125 Rail-to-Rail Output 8-pin SOIC(S), 8-pin MSOP(S), 5-pin SOT-23(S,R) MCP6L2 2 2.8 MHz 200 3 1 21(2) 2.7 to 6.0 -40 to +125 Rail-to-Rail Output 8-pin SOIC, 8-pin MSOP MCP6L4 4 2.8 MHz 200 3 1 21(2) 2.7 to 6.0 -40 to +125 Rail-to-Rail Output 14-pin SOIC, 14-pin TSSOP 1 16 (1) 2.2 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 5-pin SOT-23(S,R) (1) MCP6281 1 5 MHz 445 3 MCP6282 2 5 MHz 445 3 1 16 2.2 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin PDIP, 8-pin SOIC, 8-pin MSOP MCP6283 1 5 MHz 445 3 1 16(1) 2.2 to 6.0 -40 to +125 Rail-to-Rail Input/Output, Chip select 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 6-pin SOT-23(S,R) MCP6284 4 5 MHz 445 3 1 16(1) 2.2 to 6.0 -40 to +125 Rail-to-Rail Input/Output 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP MCP6285 2 5 MHz 400 3 1 16(1) 2.2 to 6.0 -40 to +125 Rail-to-Rail Input/Output, Dual connected, Chip select 8-pin PDIP, 8-pin SOIC, 8-pin MSOP MCP6286 1 3.5 MHz 540 1.5 1 5.4(2) 2.2 to 5.5 -40 to +125 Rail-to-Rail Output, Low noise 5-pin SOT-23(S,R) 1 (2) 2.5 to 5.5 -40 to +125 Rail-to-Rail Input/Output, 1/2 VCC VREF 8-pin PDIP, 8-pin SOIC, 8-pin TSSOP, 8-pin MSOP, 5-pin SOT-23(S,R) MCP6021 1 10 MHz 1000 0.5 8.7 Legend: S = Standard Pinout; R = Reverse Pinout; U = Alternative Pinout Note 1: Values are typical at 1 kHz 2: Values are typical at 10 kHz Analog and Interface Product Selector Guide 16 LINEAR - Op Amps (Continued) Part # MCP6022 MCP6023 # per Package GBWP IQ Typical (A) Vos Max (mV) Typical Input Bias Current (pA) Input Voltage Noise Density (nV/rtHz) Operating Voltage (V) Temperature Range (C) 2 10 MHz 1000 0.5 1 8.7(2) 2.5 to 5.5 -40 to +125 Rail-to-Rail Input/Output 8-pin PDIP, 8-pin SOIC, 8-pin TSSOP 1 8.7 (2) 2.5 to 5.5 -40 to +125 Rail-to-Rail Input/Output, Chip select, 1/2 VCC VREF 8-pin PDIP, 8-pin SOIC, 8-pin TSSOP (2) 1 10 MHz 1000 0.5 Features Packages MCP6024 4 10 MHz 1000 0.5 1 8.7 2.5 to 5.5 -40 to +125 Rail-to-Rail Input/Output 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP MCP6291 1 10 MHz 1000 3 1 8.7(2) 2.4 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 5-pin SOT-23(S,R) (2) MCP6292 2 10 MHz 1000 3 1 8.7 2.4 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin PDIP, 8-pin SOIC, 8-pin MSOP MCP6293 1 10 MHz 1000 3 1 8.7(2) 2.4 to 6.0 -40 to +125 Rail-to-Rail Input/Output, Chip select 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 6-pin SOT-23(S) MCP6294 4 10 MHz 1000 3 1 8.7(2) 2.4 to 6.0 -40 to +125 Rail-to-Rail Input/Output 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP (2) 8-pin PDIP, 8-pin SOIC, 8-pin MSOP MCP6295 2 10 MHz 1100 3 1 8.7 2.4 to 6.0 -40 to +125 Rail-to-Rail Input/Output, Dual connected, Chip select MCP6L91 1 10 MHz 850 4 1 9.4(2) 2.4 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC(S), 8-pin MSOP(S), 5-pin SOT-23(S,R) MCP6L92 2 10 MHz 850 4 1 9.4(2) 2.4 to 6.0 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin MSOP MCP6L94 4 10 MHz 850 4 1 9.4(2) 2.4 to 6.0 -40 to +125 Rail-to-Rail Input/Output 14-pin SOIC, 14-pin TSSOP 8-pin SOIC MCP621 1 20 MHz 2500 0.2 5 13(3) 2.5 to 5.5 -40 to +125 Rail-to-Rail Output, Chip select, mCal Technology (3) 2.5 to 5.5 -40 to +125 Rail-to-Rail Output, mCal Technology 5-pin SOT-23(S) 2.5 to 5.5 -40 to +125 Rail-to-Rail Output, mCal Technology 8-pin SOIC, 8-pin 3x3 DFN 6-pin SOT-23(S) MCP621S 1 20 MHz 2500 0.2 5 13 MCP622 2 20 MHz 2500 0.2 5 13(3) (3) MCP623 1 20 MHz 2500 0.2 5 13 2.5 to 5.5 -40 to +125 Rail-to-Rail Output, Chip select, mCal Technology MCP624 4 20 MHz 2500 0.2 5 13(3) 2.5 to 5.5 -40 to +125 Rail-to-Rail Output, mCal Technology 14-pin SOIC, 14-pin TSSOP MCP625 2 20 MHz 2500 0.2 5 13(3) 2.5 to 5.5 -40 to +125 10-pin MSOP, 10-pin 3x3 DFN MCP629 4 20 MHz 2500 0.2 5 13(3) 2.5 to 5.5 -40 to +125 Rail-to-Rail Output, Chip selects, mCal Technology Rail-to-Rail Output,Chip selects, mCal Technology (3) 8-pin SOIC 16-pin 4x4 QFN MCP631 1 24 MHz 2500 8 4 10 2.5 to 5.5 -40 to +125 Rail-to-Rail Output MCP632 2 24 MHz 2500 8 4 10(3) 2.5 to 5.5 -40 to +125 Rail-to-Rail Output 8-pin SOIC, 8-pin 3x3 DFN MCP633 1 24 MHz 2500 8 4 10(3) 2.5 to 5.5 -40 to +125 Rail-to-Rail Output, Chip select 8-pin SOIC MCP635 2 24 MHz 2500 8 4 10(3) 2.5 to 5.5 -40 to +125 Rail-to-Rail Output, Chip selects 10-pin MSOP, 10-pin 3x3 DFN 6 7.5 (3) 2.5 to 5.5 -40 to +125 Rail-to-Rail Output, Chip select, mCal Technology 8-pin SOIC 7.5 (3) 2.5 to 5.5 -40 to +125 Rail-to-Rail Output, mCal Technology 5-pin SOT-23(S) (3) MCP651 1 MCP651S 1 50 MHz 50 MHz 6000 6000 0.2 0.2 6 MCP652 2 50 MHz 6000 0.2 6 7.5 2.5 to 5.5 -40 to +125 Rail-to-Rail Output, mCal Technology 8-pin SOIC, 8-pin 3x3 DFN MCP653 1 50 MHz 6000 0.2 6 7.5(3) 2.5 to 5.5 -40 to +125 Rail-to-Rail Output, Chip select, mCal Technology 6-pin SOT-23(S) 6 7.5 (3) 2.5 to 5.5 -40 to +125 Rail-to-Rail Output, mCal Technology 14-pin SOIC, 14-pin TSSOP 7.5 (3) 2.5 to 5.5 -40 to +125 10-pin MSOP, 10-pin 3x3 DFN (3) 2.5 to 5.5 -40 to +125 Rail-to-Rail Output, Chip selects, mCal Technology Rail-to-Rail Output,Chip selects, mCal Technology (3) 8-pin SOIC MCP654 MCP655 MCP659 4 2 4 50 MHz 50 MHz 50 MHz 6000 6000 6000 0.2 0.2 0.2 6 6 7.5 16-pin 4x4 QFN MCP661 1 60 MHz 6000 8 6 6.8 2.5 to 5.5 -40 to +125 Rail-to-Rail Output MCP662 2 60 MHz 6000 8 6 6.8(3) 2.5 to 5.5 -40 to +125 Rail-to-Rail Output 8-pin SOIC, 8-pin 3x3 DFN MCP663 1 60 MHz 6000 8 6 6.8(3) 2.5 to 5.5 -40 to +125 Rail-to-Rail Output, Chip select 8-pin SOIC MCP665 2 60 MHz 6000 8 6 6.8(3) 2.5 to 5.5 -40 to +125 Rail-to-Rail Output, Chip selects 10-pin MSOP, 10-pin 3x3 DFN Legend: Note 1: 2: 3: S = Standard Pinout; R = Reverse Pinout; U = Alternative Pinout Values are typical at 1 kHz Values are typical at 10 kHz Values are typical at 1 MHz Analog and Interface Product Selector Guide 17 LINEAR - High Precision Operational Amplifiers Part # # per Package GBWP IQ Max (mA) Vos Max (V) Vos Drift Max (V/C) Operating Voltage (V) Temperature Range (C) Features Packages Chopper Stabilized TC7650 1 2.0 MHz 3.5 5 0.05 4.5 to 16 0 to +70 Single and Split Supply 8-pin PDIP, 14-pin PDIP TC7652 1 0.4 MHz 3 5 0.05 5 to 16 0 to +70 Single and Split Supply, Low Noise 8-pin PDIP, 14-pin PDIP Auto-Zero MCP6V01 1 1.3 MHz 0.4 2 0.05 1.8 to 5.5 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin 2x3 TDFN MCP6V02 2 1.3 MHz 0.4 2 0.05 1.8 to 5.5 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin 4x4 DFN MCP6V03 1 1.3 MHz 0.4 2 0.05 1.8 to 5.5 -40 to +125 Rail-to-Rail Input/Output, Chip select 8-pin SOIC, 8-pin 2x3 TDFN MCP6V06 1 1.3 MHz 0.4 3 0.05 1.8 to 5.5 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin 2x3 TDFN MCP6V07 2 1.3 MHz 0.4 3 0.05 1.8 to 5.5 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin 4x4 DFN MCP6V08 1 1.3 MHz 0.4 3 0.05 1.8 to 5.5 -40 to +125 Rail-to-Rail Input/Output, Chip select 8-pin SOIC, 8-pin 2x3 TDFN MCP6V26 1 2 MHz 0.8 2 0.05 2.3 to 5.5 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin MSOP, 8-pin 2x3 TDFN MCP6V27 2 2 MHz 0.8 2 0.05 2.3 to 5.5 -40 to +125 Rail-to-Rail Input/Output 8-pin SOIC, 8-pin MSOP, 8-pin 4x4 DFN MCP6V28 1 2 MHz 0.8 2 0.05 2.3 to 5.5 -40 to +125 TC913A/B 2 1.5 MHz 1.1 15 0.15/0.30 7 to 16 0 to +70 Rail-to-Rail Input/Output, Chip select 8-pin SOIC, 8-pin MSOP, 8-pin 2x3 TDFN Single and Split Supply 8-pin PDIP, 8-pin SOIC LINEAR - Programmable Gain Amplifiers (PGA) Channels -3dB BW (MHz) IQ Typ. (mA) Vos (V) Operating Voltage (V) Temperature Range (C) MCP6S21 1 2 to 12 1.1 275 2.5 to 5.5 -40 to +85 SPI, 8 Gain steps, Software shutdown 8-pin PDIP, 8-pin SOIC, 8-pin MSOP MCP6S22 2 2 to 12 1.1 275 2.5 to 5.5 -40 to +85 SPI, 8 Gain steps, Software shutdown 8-pin PDIP, 8-pin SOIC, 8-pin MSOP MCP6S26 6 2 to 12 1.1 275 2.5 to 5.5 -40 to +85 SPI, 8 Gain steps, Software shutdown 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP MCP6S28 8 2 to 12 1.1 275 2.5 to 5.5 -40 to +85 SPI, 8 Gain steps, Software shutdown 16-pin PDIP, 16-pin SOIC MCP6S91 1 1 to 18 1.0 4000 2.5 to 5.5 -40 to +125 SPI, 8 Gain steps, Software shutdown, VREF 8-pin PDIP, 8-pin SOIC, 8-pin MSOP MCP6S92 2 1 to 18 1.0 4000 2.5 to 5.5 -40 to +125 SPI, 8 Gain steps, Software shutdown 8-pin PDIP, 8-pin SOIC, 8-pin MSOP MCP6S93 2 1 to 18 1.0 4000 2.5 to 5.5 -40 to +125 SPI, 8 Gain steps, Software shutdown, VREF, SO 10-pin MSOP Part # Features Packages LINEAR - Selectable Gain Amplifiers (SGA) Channels -3dB BW (kHz) IQ (A) VOS (mV) Operating Voltage (V) Temperature Range (C) Gain Steps (V/V) MCP6G01 1 900 110 4.5 1.8 to 5.5 -40 to +125 1, 10, 50 Tri-State control pin 8-pin SOIC, 8-pin MSOP, 5-pin SOT-23 (S,R,U) MCP6G02 2 900 110 4.5 1.8 to 5.5 -40 to +125 1, 10, 50 Tri-State control pin 8-pin SOIC, 8-pin MSOP 8-pin SOIC, 8-pin MSOP 14-pin SOIC, 14-pin TSSOP Part # Features MCP6G03 1 900 110 4.5 1.8 to 5.5 -40 to +125 1, 10, 50 Tri-State control pin, Chip select MCP6G04 4 900 110 4.5 1.8 to 5.5 -40 to +125 1, 10, 50 Tri-State control pin Packages Analog and Interface Product Selector Guide 18 LINEAR - Comparators Part # MCP6541 # per Package VREF (V) 1 Typical Propagation Delay (s) - IQ Typical (A) 4 Vos Max (mV) 1 5 Operating Voltage (V) 1.6 to 5.5 Temperature Range (C) -40 to +125 Features Packages (S,R,U) 5-pin SOT-23 , 5-pin SC-70(S,U), 8-pin PDIP, 8-pin SOIC, 8-pin MSOP Push-Pull, Rail-to-Rail Input/Output MCP6542 2 - 4 1 5 1.6 to 5.5 -40 to +125 Push-Pull, Rail-to-Rail Input/Output 8-pin PDIP, 8-pin SOIC, 8-pin MSOP MCP6543 1 - 4 1 5 1.6 to 5.5 -40 to +125 Push-Pull, Rail-to-Rail Input/Output, Chip select 8-pin PDIP, 8-pin SOIC, 8-pin MSOP MCP6544 4 - 4 1 5 1.6 to 5.5 -40 to +125 Push-Pull, Rail-to-Rail Input/Output 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP MCP6546 1 - 4 1 5 1.6 to 5.5 -40 to +125 Open-drain, 9V, Rail-to-Rail Input/Output 5-pin SOT-23(S,R,U), 5-pin SC-70(S,U), 8-pin PDIP, 8-pin SOIC, 8-pin MSOP MCP6547 2 - 4 1 5 1.6 to 5.5 -40 to +125 Open-drain, 9V, Rail-to-Rail Input/Output 8-pin PDIP, 8-pin SOIC, 8-pin MSOP MCP6548 1 - 4 1 5 1.6 to 5.5 -40 to +125 Open-drain, 9V, Rail-to-Rail Input/Output, Chip select 8-pin PDIP, 8-pin SOIC, 8-pin MSOP MCP6549 4 - 4 1 5 1.6 to 5.5 -40 to +125 Open-drain, 9V, Rail-to-Rail Input/Output 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP MCP65R41 1 1.21/2.4 4 2.5 10 1.8 to 5.5 -40 to +125 Push-Pull, Rail-to-Rail Input/Output, VREF 6-pin SOT-23 MCP65R46 1 1.21/2.4 4 2.5 10 1.8 to 5.5 -40 to +125 Open Drain, Rail-to-Rail Input/Output, VREF 6-pin SOT-23 MCP6561 1 - 0.047 100 10 1.8 to 5.5 -40 to +125 Push-Pull, Rail-to-Rail Input/Output 5-pin SOT-23(S,R,U), 5-pin SC-70(S) MCP6562 2 - 0.047 100 10 1.8 to 5.5 -40 to +125 Push-Pull, Rail-to-Rail Input/Output 8-pin SOIC, 8-pin MSOP MCP6564 4 - 0.047 100 10 1.8 to 5.5 -40 to +125 Push-Pull, Rail-to-Rail Input/Output 14-pin SOIC, 14-pin TSSOP MCP6566 1 - 0.047 100 10 1.8 to 5.5 -40 to +125 Open-Drain, Rail-to-Rail Input/Output 5-pin SOT-23(S,R,U), 5-pin SC-70(S) MCP6567 2 - 0.047 100 10 1.8 to 5.5 -40 to +125 Open-Drain, Rail-to-Rail Input/Output 8-pin SOIC, 8-pin MSOP MCP6569 4 - 0.047 100 10 1.8 to 5.5 -40 to +125 Open-Drain, Rail-to-Rail Input/Output 14-pin SOIC, 14-pin TSSOP Legend: S = Standard Pinout; R = Reverse Pinout; U = Alternative Pinout MIXED SIGNAL MIXED SIGNAL - Successive Approximation Register (SAR) A/D Converters Resolution (bits) Maximum Sampling Rate (ksamples/sec) # of Input Channels Input Type Interface Input Voltage Range (V) Max. Supply Current (A) Max. INL Temperature Range (C) MCP3021 10 22 1 Single-ended I2CTM 2.7 to 5.5 250 1 LSB -40 to +125 MCP3001 10 200 1 Single-ended SPI 2.7 to 5.5 500 1 LSB -40 to +85 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin TSSOP MCP3002 10 200 2 Single-ended SPI 2.7 to 5.5 650 1 LSB -40 to +85 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin TSSOP Part # Packages 5-pin SOT-23A MCP3004 10 200 4 Single-ended SPI 2.7 to 5.5 550 1 LSB -40 to +85 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP MCP3008 10 200 8 Single-ended SPI 2.7 to 5.5 550 1 LSB -40 to +85 16-pin PDIP, 16-pin SOIC MCP3221 12 22 1 Single-ended I2CTM 2.7 to 5.5 250 2 LSB -40 to +125 5-pin SOT-23A MCP3201 12 100 1 Single-ended SPI 2.7 to 5.5 400 1 LSB -40 to +85 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin TSSOP MCP3202 12 100 2 Single-ended SPI 2.7 to 5.5 550 1 LSB -40 to +85 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin TSSOP MCP3204 12 100 4 Single-ended SPI 2.7 to 5.5 400 1 LSB -40 to +85 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP MCP3208 12 100 8 Single-ended SPI 2.7 to 5.5 400 1 LSB -40 to +85 16-pin PDIP, 16-pin SOIC MCP3301 13 100 1 Differential SPI 2.7 to 5.5 450 1 LSB -40 to +85 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin TSSOP MCP3302 13 100 2 Differential SPI 2.7 to 5.5 450 1 LSB -40 to +85 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP MCP3304 13 100 4 Differential SPI 2.7 to 5.5 450 1 LSB -40 to +85 16-pin PDIP, 16-pin SOIC Analog and Interface Product Selector Guide 19 MIXED SIGNAL - Delta-Sigma A/D Converters Part # MCP3421 Resolution (bits) Maximum Sampling Rate (samples/sec) # of Input Channels Interface Supply Voltage Range (V) Typical Supply Current (A) Typical INL (ppm) Temperature Range (C) 18 to 12 4 to 240 1 Diff I2CTM 2.7 to 5.5 155 10 -40 to +125 PGA, VREF 2 Features Packages 6-pin SOT-23A MCP3422 18 to 12 4 to 240 2 Diff I CTM 2.7 to 5.5 145 10 -40 to +125 PGA, VREF 8-pin SOIC, 8-pin MSOP, 8-pin 2x3 DFN MCP3423 18 to 12 4 to 240 2 Diff I2CTM 2.7 to 5.5 145 10 -40 to +125 PGA, VREF, Selectable I2CTM addressing 10-pin MSOP, 10-pin 3x3 DFN MCP3424 18 to 12 4 to 240 4 Diff I2CTM 2.7 to 5.5 145 10 -40 to +125 PGA, VREF, Selectable I2CTM addressing 14-pin SOIC, 14-pin TSSOP MCP3425 16 to 12 15 to 240 1 Diff I2CTM 2.7 to 5.5 155 10 -40 to +125 PGA, VREF 6-pin SOT-23A 2 MCP3426 16 to 12 15 to 240 2 Diff I CTM 2.7 to 5.5 145 10 -40 to +125 PGA, VREF 8-pin SOIC, 8-pin MSOP, 8-pin 2x3 DFN MCP3427 16 to 12 15 to 240 2 Diff I2CTM 2.7 to 5.5 145 10 -40 to +125 PGA, VREF, Selectable I2CTM addressing 10-pin MSOP, 10-pin 3x3 DFN MCP3428 16 to 12 15 to 240 4 Diff I2CTM 2.7 to 5.5 145 10 -40 to +125 PGA, VREF, Selectable I2CTM addressing 14-pin SOIC, 14-pin TSSOP MCP3550-50 22 13 1 Diff SPI 2.7 to 5.5 120 2 -40 to +125 50 Hz rejection 8-pin SOIC, 8-pin MSOP MCP3550-60 22 15 1 Diff SPI 2.7 to 5.5 140 2 -40 to +125 60 Hz rejection 8-pin SOIC, 8-pin MSOP MCP3551 22 14 1 Diff SPI 2.7 to 5.5 120 2 -40 to +125 Simultaneous 50/60 Hz rejection 8-pin SOIC, 8-pin MSOP MCP3553 20 60 1 Diff SPI 2.7 to 5.5 140 2 -40 to +125 8-pin SOIC, 8-pin MSOP MIXED SIGNAL - Energy Measurement ICs Dynamic Range Typical Accuracy ADC Channels Gain Selection Output Type Typical Voltage Reference Drift (ppm/C) Typical Supply Current (mA) Analog Voltage Range (V) Digital Voltage Range (V) Temperature Range (C) MCP3901 24-bit resolution 91 dB SINAD 2 up to 32 SPI 12 2.6 4.5 to 5.5 2.7 to 5.5 -40 to +125 Phase correction, Programmable data rate 20-pin SSOP, 20-pin 4x4 QFN MCP3903 24-bit resolution 91 dB SINAD 6 up to 32 SPI 5 8.3 4.5 to 5.5 2.7 to 3.6 -40 to +125 Phase correction, Programmable data rate 28-pin SSOP 500:1 0.1% 2 up to 16 Active power pulse 15 3.9 4.5 to 5.5 4.5 to 5.5 -40 to +125 Active power calculation 24-pin SSOP 24-pin SSOP Part # MCP3905A Features Packages Active power pulse 15 3.9 4.5 to 5.5 4.5 to 5.5 -40 to +125 Active power calculation, Reduced pulse-width up to 32 Active power pulse 15 3.9 4.5 to 5.5 4.5 to 5.5 -40 to +125 Active power calculation 24-pin SSOP up to 16 Active power pulse/ SPI 15 3.9 4.5 to 5.5 4.5 to 5.5 -40 to +125 Active power calculation 24-pin SSOP MCP3905L 500:1 0.1% 2 up to 16 MCP3906A 1000:1 0.1% 2 MCP3909 1000:1 0.1% 2 MIXED SIGNAL - Dual Slope A/D Converters Part # Supply Voltage (V) Input Voltage Range Resolution Sampling Rate (Conv/s) Input Channels Data Interface Temperature Range (C) TC500 4.5 to 7.5 VSS + 1.5V to VDD - 1.5V Up to 16 bits 4 to 10 1 3-Wire 0 to +70 Differential input range, Programmable resolution/ conversion time 16-pin PDIP, 16-pin SOIC, 16-pin CerDIP TC500A 4.5 to 7.5 VSS + 1.5V to VDD - 1.5V Up to 17 bits 4 to 10 1 3-Wire 0 to +70 Differential input range, Programmable resolution/ conversion time 16-pin PDIP, 16-pin SOIC, 16-pin CerDIP TC510 +4.5 to +5.5 VSS + 1.5V to VDD - 1.5V Up to 17 bits 4 to 10 1 3-Wire 0 to +70 Differential input range, Programmable resolution/ conversion time, Charge pump (-V) output pin 24-pin PDIP, 24-pin SOIC TC514 +4.5 to +5.5 VSS + 1.5V to VDD - 1.5V Up to 17 bits 4 to 10 4 3-Wire 0 to +70 Differential input range, Programmable resolution/ conversion time, Charge pump (-V) output pin 28-pin PDIP, 28-pin SOIC TC520A +4.5 to +5.5 - - - - Serial port 0 to +70 Optional serial interface adapter for TC500/500A/510/514 14-pin PDIP, 16-pin SOIC TC7109 4.5 to 5.5 VSS + 1.5V to VDD - 1.0V 12 bits plus sign bit 2 to 10 1 Parallel or Serial port -25 to +85 Differential input range 40-pin PDIP, 44-pin PLCC, 44-pin MQFP TC7109A 4.5 to 5.5 VSS + 1.5V to VDD - 1.0V 12 bits plus sign bit 2 to 10 1 Parallel or Serial port -25 to +85 Differential input range 40-pin PDIP, 44-pin PLCC, 44-pin MQFP Features Packages Analog and Interface Product Selector Guide 20 MIXED SIGNAL - Binary and BCD A/D Converters Part # Description Supply Voltage (V) Input Voltage Range Resolution (Digits) Resolution (Counts) Max Power (mW) Data Interface Temperature Range (C) TC850 Binary A/D 5 VSS + 1.5V to VDD - 1.5V 15-bit 32,768 35 8-bit parallel -25 to +70 Highest conversion speed (40 conv/sec) 44-pin PLCC, 40-pin PDIP TC14433 BCD A/D 4.5 to 8 199.9 mV to 1.999V 31/2 2,000 20 MUXed BCD -40 to +85 For DMM, DPM, Data loggers 24-pin SOIC, 24-pin PDIP, 28-pin PLCC TC14433A BCD A/D 4.5 to 8 199.9 mV to 1.999V 31/2 2,000 20 MUXed BCD -40 to +85 For DMM, DPM, Data loggers 24-pin PDIP, 28-pin PLCC Features Packages MIXED SIGNAL - Display A/D Converters Display Type Supply Voltage (V) Resolution (Digits) Resolution (Counts) Power (mW) Temperature Range (C) TC7106 LCD 9 31/2 2,000 10 -25 to +85 For DMM, DPM, Data logger applications 40-pin PDIP, 44-pin PLCC, 44-pin MQFP TC7106A LCD 9 31/2 2,000 10 -25 to +85 For DMM, DPM, Data logger applications 40-pin PDIP, 44-pin PLCC, 44-pin MQFP TC7107 LED 5 31/2 2,000 10 -25 to +85 For DMM, DPM, Data logger applications 40-pin PDIP, 44-pin PLCC, 44-pin MQFP TC7107A LED 5 31/2 2,000 10 -25 to +85 For DMM, DPM, Data logger applications 40-pin PDIP, 44-pin PLCC, 44-pin MQFP TC7116 LCD 9 31/2 2,000 10 -25 to +85 Hold function 40-pin PDIP, 44-pin PLCC, 44-pin MQFP TC7116A LCD 9 31/2 2,000 10 -25 to +85 Hold function 40-pin PDIP, 44-pin PLCC, 44-pin MQFP TC7117 LED 5 31/2 2,000 10 -25 to +85 Hold function 40-pin PDIP, 44-pin PLCC, 44-pin MQFP TC7117A LED 5 31/2 2,000 10 -25 to +85 Hold function 40-pin PDIP, 44-pin PLCC, 44-pin MQFP TC7126 LCD 9 31/2 2,000 0.5 -25 to +85 Low-power TC7106 40-pin PDIP, 44-pin PLCC, 44-pin MQFP TC7126A LCD 9 31/2 2,000 0.5 -25 to +85 Low-power TC7106 40-pin PDIP, 44-pin PLCC, 44-pin MQFP TC7129 LCD 9 41/2 20,000 4.5 0 to +70 Lowest noise 3 mV sensitivity 40-pin PDIP, 44-pin PLCC, 44-pin MQFP Part # Features Packages MIXED SIGNAL - Digital Potentiometers Number of Taps Memory Number per Package Interface Resistance (kOhms) INL (max) DNL (max) Temperature Range (C) MCP4011 64 Volatile 1 Up/Down 2.1, 5, 10, 50 0.5 0.5 -40 to +125 Potentiometer mode 8-pin SOIC, 8-pin MSOP, 8-pin 2x3 DFN MCP4012 64 Volatile 1 Up/Down 2.1, 5, 10, 50 0.5 0.5 -40 to +125 Rheostat mode 6-pin SOT-23 MCP4013 64 Volatile 1 Up/Down 2.1, 5, 10, 50 0.5 0.5 -40 to +125 Potentiometer to VSS 6-pin SOT-23 MCP4014 64 Volatile 1 Up/Down 2.1, 5, 10, 50 0.5 0.5 -40 to +125 Rheostat to VSS 5-pin SOT-23 MCP4017 128 Volatile 1 I2CTM 5, 10, 50, 100 0.5 0.25 -40 to +125 7-bit, Volatile, I2C digital potentiometer 6-pin SC-70 MCP4018 128 Volatile 1 I2CTM 5, 10, 50, 100 0.5 0.25 -40 to +125 7-bit, Volatile, I2C digital potentiometer 6-pin SC-70 Part # 2 Comments Packages MCP4019 128 Volatile 1 I CTM 5, 10, 50, 100 0.5 0.25 -40 to +125 7-bit, Volatile, I2C digital potentiometer 5-pin SC-70 MCP40D17 128 Volatile 1 I2CTM 5, 10, 50, 100 0.5 0.25 -40 to +125 7-bit, Volatile, I2C digital potentiometer 6-pin SC-70 MCP40D18 128 Volatile 1 I2CTM 5, 10, 50, 100 0.5 0.25 -40 to +125 7-bit, Volatile, I2C digital potentiometer 6-pin SC-70 MCP40D19 128 Volatile 1 I2CTM 5, 10, 50, 100 0.5 0.25 -40 to +125 7-bit, Volatile, I2C digital potentiometer 5-pin SC-70 MCP4021 64 Nonvolatile 1 Up/Down 2.1, 5, 10, 50 0.5 0.5 -40 to +125 Potentiometer mode, Shutdown, WiperLockTM Technology 8-pin SOIC, 8-pin MSOP, 8-pin 2x3 DFN MCP4022 64 Nonvolatile 1 Up/Down 2.1, 5, 10, 50 0.5 0.5 -40 to +125 Rheostat mode, Shutdown, WiperLockTM Technology 6-pin SOT-23 MCP4023 64 Nonvolatile 1 Up/Down 2.1, 5, 10, 50 0.5 0.5 -40 to +125 Potentiometer to VSS, WiperLockTM Technology 6-pin SOT-23 MCP4024 64 Nonvolatile 1 Up/Down 2.1, 5, 10, 50 0.5 0.5 -40 to +125 Rheostat to VSS, Shutdown, WiperLockTM Technology 5-pin SOT-23 MCP4141 128 Nonvolatile 1 SPI 5, 10, 50, 100 0.5 0.25 -40 to +125 Potentiometer mode, Shutdown 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin 3x3 DFN MCP4142 128 Nonvolatile 1 SPI 5, 10, 50, 100 0.8 0.25 -40 to +125 Rheostat mode, Shutdown 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin 3x3 DFN MCP4241 128 Nonvolatile 2 SPI 5, 10, 50, 100 0.5 0.25 -40 to +125 Potentiometer mode, Shutdown, WiperLockTM Technology 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP, 16-pin 4x4 QFN MCP4242 128 Nonvolatile 2 SPI 5, 10, 50, 100 0.8 0.25 -40 to +125 Rheostat mode, Shutdown 10-pin MSOP, 10-pin 3x3 DFN Analog and Interface Product Selector Guide 21 MIXED SIGNAL - Digital Potentiometers (Continued) Number of Taps Memory Number per Package Interface Resistance (kOhms) INL (max) DNL (max) Temperature Range (C) MCP4131 128 Volatile 1 SPI 5, 10, 50, 100 0.5 0.25 -40 to +125 Potentiometer mode, Shutdown 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin 3x3 DFN MCP4132 128 Volatile 1 SPI 5, 10, 50, 100 0.8 0.25 -40 to +125 Rheostat mode, Shutdown 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin 3x3 DFN MCP4231 128 Volatile 2 SPI 5, 10, 50, 100 0.5 0.25 -40 to +125 Potentiometer mode, Shutdown, WiperLockTM Technology 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP, 16-pin 4x4 QFN MCP4232 128 Volatile 2 SPI 5, 10, 50, 100 0.8 0.25 -40 to +125 Rheostat mode, Shutdown 10-pin MSOP, 10-pin 3x3 DFN MCP41010 256 Volatile 1 SPI 10 1 1 -40 to +85 Potentiometer mode, Shutdown 8-pin PDIP, 8-pin SOIC MCP41050 256 Volatile 1 SPI 50 1 1 -40 to +85 Potentiometer mode, Shutdown 8-pin PDIP, 8-pin SOIC MCP41100 256 Volatile 1 SPI 100 1 1 -40 to +85 Potentiometer mode, Shutdown 8-pin PDIP, 8-pin SOIC MCP4151 256 Volatile 1 SPI 5, 10, 50, 100 1 0.5 -40 to +125 Potentiometer mode, Shutdown 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin 3x3 DFN MCP4152 256 Volatile 1 SPI 5, 10, 50, 100 1 0.5 -40 to +125 Rheostat mode, Shutdown 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin 3x3 DFN MCP4161 256 Nonvolatile 1 SPI 5, 10, 50, 100 1 0.5 -40 to +125 Potentiometer mode, Shutdown 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin 3x3 DFN MCP4162 256 Nonvolatile 1 SPI 5, 10, 50, 100 1 0.5 -40 to +125 Rheostat mode, Shutdown 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin 3x3 DFN MCP42010 256 Volatile 2 SPI 10 1 1 -40 to +85 Potentiometer mode, Shutdown 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP MCP42100 256 Volatile 2 SPI 100 1 1 -40 to +85 Potentiometer mode, Shutdown 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP MCP4251 256 Volatile 2 SPI 5, 10, 50, 100 1 0.5 -40 to +125 Potentiometer mode, Shutdown, WiperLockTM Technology 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP, 16-pin 4x4 QFN MCP4252 256 Volatile 2 SPI 5, 10, 50, 100 1 0.5 -40 to +125 Rheostat mode, Shutdown 10-pin MSOP, 10-pin 3x3 DFN MCP4261 256 Nonvolatile 2 SPI 5, 10, 50, 100 1 0.5 -40 to +125 Potentiometer mode, Shutdown, WiperLockTM Technology 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP, 16-pin 4x4 QFN MCP4262 256 Nonvolatile 2 SPI 5, 10, 50, 100 1 0.5 -40 to +125 Rheostat mode, Shutdown 10-pin MSOP, 10-pin 3x3 DFN MCP4341 129 Nonvolatile 4 I2CTM 5, 10, 50, 100 0.8 0.375 -40 to +125 7-bit, Volatile potentiometer with an I2C interface 20-pin TSSOP, 20-pin 4x4 QFN MCP4342 129 Nonvolatile 4 I2CTM 5, 10, 50, 100 0.8 0.375 -40 to +125 7-bit, Volatile rheostat with an I2C interface 14-pin TSSOP MCP4361 257 Nonvolatile 4 I2CTM 5, 10, 50, 100 1 0.5 -40 to +125 8-bit, Non-volatile potentiometer with an I2C interface 20-pin TSSOP, 20-pin 4x4 QFN Part # 2 Comments Packages MCP4362 257 Nonvolatile 4 I CTM 5, 10, 50, 100 1 0.5 -40 to +125 8-bit, Non-volatile rheostat with an I2C interface 14-pin TSSOP MCP4331 129 Volatile 4 I2CTM 5, 10, 50, 100 0.8 0.375 -40 to +125 7-bit, Volatile potentiometer with an I2C interface 20-pin TSSOP, 20-pin 4x4 QFN MCP4332 129 Volatile 4 I2CTM 5, 10, 50, 100 0.8 0.375 -40 to +125 7-bit, Volatile rheostat with an I2C interface 14-pin TSSOP 2 2 MCP4351 257 Volatile 4 I CTM 5, 10, 50, 100 1 0.5 -40 to +125 8-bit, Non-volatile potentiometer with an I C interface MCP4352 257 Volatile 4 I2CTM 5, 10, 50, 100 1 0.5 -40 to +125 8-bit, Non-volatile rheostat with an I2C interface 14-pin TSSOP MCP4441 129 Nonvolatile 4 I2CTM 5, 10, 50, 100 0.5 0.25 -40 to +125 Potentiometer mode, WiperLockTM Technology 20-pin TSSOP, 20-pin 4x4 QFN MCP4442 129 Nonvolatile 4 I2CTM 5, 10, 50, 101 0.8 0.375 -40 to +125 Rheostat mode, WiperLockTM Technology 14-pin TSSOP 2 20-pin TSSOP, 20-pin 4x4 QFN MCP4461 257 Nonvolatile 4 I CTM 5, 10, 50, 102 1 0.5 -40 to +125 Potentiometer mode, WiperLockTM Technology 20-pin TSSOP, 20-pin 4x4 QFN MCP4462 257 Nonvolatile 4 I2CTM 5, 10, 50, 103 1 0.5 -40 to +125 Rheostat mode, WiperLockTM Technology 14-pin TSSOP MCP4531 128 Volatile 1 I2CTM 5, 10, 50, 100 0.5 0.25 -40 to +125 Potentiometer mode 8-pin MSOP MCP4631 128 Volatile 2 I2CTM 5, 10, 50, 100 0.5 0.25 -40 to +125 Potentiometer mode 14-pin TSSOP, 16-pin 4x4 QFN 2 MCP4541 128 Nonvolatile 1 I CTM 5, 10, 50, 100 0.5 0.25 -40 to +125 Potentiometer mode, WiperLockTM Technology 8-pin MSOP MCP4641 128 Nonvolatile 2 I2CTM 5, 10, 50, 100 0.5 0.25 -40 to +125 Potentiometer mode, WiperLockTM Technology 14-pin TSSOP, 16-pin 4x4 QFN MCP4551 256 Volatile 1 I2CTM 5, 10, 50, 100 1 0.5 -40 to +125 Potentiometer mode 8-pin MSOP MCP4651 256 Volatile 2 I2CTM 5, 10, 50, 100 1 0.5 -40 to +125 Potentiometer mode 14-pin TSSOP, 16-pin 4x4 QFN 5, 10, 50, 100 1 0.5 -40 to +125 Potentiometer mode, WiperLockTM Technology 8-pin MSOP MCP4561 256 Nonvolatile 1 2 I CTM Analog and Interface Product Selector Guide 22 MIXED SIGNAL - Digital Potentiometers (Continued) Part # Number of Taps Number per Package Memory Interface 2 Resistance (kOhms) INL (max) DNL (max) Temperature Range (C) Comments Packages MCP4661 256 Nonvolatile 2 I CTM 5, 10, 50, 100 1 0.5 -40 to +125 Potentiometer mode, WiperLockTM Technology 14-pin TSSOP, 16-pin 4x4 QFN MCP4532 128 Nonvolatile 1 I2CTM 5, 10, 50, 100 0.8 0.375 -40 to +125 Rheostat mode 8-pin MSOP, 8-pin 3x3 DFN MCP4632 128 Nonvolatile 2 I2CTM 5, 10, 50, 100 0.8 0.375 -40 to +125 Rheostat mode 10-pin MSOP, 10-pin 3x3 DFN MCP4542 128 Nonvolatile 1 I2CTM 5, 10, 50, 100 0.8 0.375 -40 to +125 Rheostat mode, WiperLockTM Technology 8-pin MSOP, 8-pin 3x3 DFN MCP4642 128 Nonvolatile 2 I2CTM 5, 10, 50, 100 0.8 0.375 -40 to +125 Rheostat mode, WiperLockTM Technology 10-pin MSOP, 10-pin 3x3 DFN MCP4552 256 Nonvolatile 1 I2CTM 5, 10, 50, 100 1 0.5 -40 to +125 Rheostat mode 8-pin MSOP, 8-pin 3x3 DFN MCP4652 256 Nonvolatile 2 I2CTM 5, 10, 50, 100 1 0.5 -40 to +125 Rheostat mode 10-pin MSOP, 10-pin 3x3 DFN MCP4562 256 Nonvolatile 1 I2CTM 5, 10, 50, 100 1 0.5 -40 to +125 Rheostat mode, WiperLockTM Technology 8-pin MSOP, 8-pin 3x3 DFN MCP4662 256 Nonvolatile 2 I2CTM 5, 10, 50, 100 1 0.5 -40 to +125 Rheostat mode, WiperLockTM Technology 10-pin MSOP, 10-pin 3x3 DFN MIXED SIGNAL - Frequency-to-Voltage/Voltage-to-Frequency Converters Part # Frequency Range (kHz) Full Scale (ppm FS/C) Non-linearity (%FS) Temperature Range (C) 100 40 0.05 -40 to +85 TC9400 Packages 14-pin PDIP, 14-pin SOIC TC9401 100 40 0.02 -40 to +85 14-pin PDIP, 14-pin SOIC TC9402 100 100 0.25 -40 to +85 14-pin PDIP, 14-pin SOIC MIXED SIGNAL - D/A Converters Resolution (Bits) DACs per Package Interface VREF Output Settling Time (s) DNL (LSB) Typical Standby Current (A) Typical Operating Current (A) Temperature Range (C) TC1320 8 1 SMbus Ext 10 0.8 0.1 350 -40 to +85 TC1321 10 1 SMbus Ext 10 2 0.1 350 -40 to +85 8-pin MSOP, 8-pin SOIC MCP4706 8 1 I2CTM Ext 6 0.05 0.06 210 -40 to +125 6-pin SOT-23 MCP4716 10 1 I2CTM Ext 6 0.188 0.06 210 -40 to +125 6-pin SOT-23 MCP4725 12 1 I2CTM VDD 6 0.75 1 210 -40 to +125 6-pin SOT-23 MCP4726 12 1 I2CTM Ext 6 0.75 0.06 210 -40 to +125 6-pin SOT-23 MCP4728 12 4 I2CTM Int/VDD 6 0.75 0.04 800 -40 to +125 10-pin MSOP Part # Packages 8-pin MSOP, 8-pin SOIC MCP4801 8 1 SPI Int 4.5 0.5 0.3 330 -40 to +125 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin DFN MCP4802 8 2 SPI Int 4.5 0.5 3.3 415 -40 to +125 8-pin PDIP, 8-pin SOIC, 8-pin MSOP MCP4811 10 1 SPI Int 4.5 0.5 0.3 330 -40 to +125 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin DFN MCP4812 10 2 SPI Int 4.5 0.5 3.3 415 -40 to +125 8-pin PDIP, 8-pin SOIC, 8-pin MSOP MCP4821 12 1 SPI Int 4.5 1 0.3 330 -40 to +125 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin DFN MCP4822 12 2 SPI Int 4.5 1 3.3 415 -40 to +125 8-pin PDIP, 8-pin SOIC, 8-pin MSOP MCP4901 8 1 SPI Ext 4.5 0.5 3.3 175 -40 to +125 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin DFN MCP4902 8 2 SPI Ext 4.5 0.5 0.3 350 -40 to +125 14-pin PDIP, 14-pin SOIC, 14-pinTSSOP MCP4911 10 1 SPI Ext 4.5 0.5 3.3 175 -40 to +125 8-pin DFN, 8-pin MSOP, 8-pin PDIP, 8-pin SOIC MCP4912 10 2 SPI Ext 4.5 0.5 0.3 350 -40 to +125 14-pin PDIP, 14-pin SOIC, 14-pinTSSOP MCP4921 12 1 SPI Ext 4.5 0.75 3.3 175 -40 to +125 8-pin PDIP, 8-pin SOIC, 8-pin MSOP, 8-pin DFN MCP4922 12 2 SPI Ext 4.5 0.75 0.3 350 -40 to +125 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP Note: The analog output is voltage. Analog and Interface Product Selector Guide 23 INTERFACE INTERFACE - Controller Area Network (CAN) Products Operating Voltage (V) Temperature Range (C) Tx Buffers Rx Buffers Filters Masks Interrupt Output MCP2510(1) 2.7 to 5.5 -40 to +125 3 2 6 2 Yes CAN 2.0B Active controller with SPI interface to MCU, 3 transmit buffers, 2 receive buffers, HW and SW message triggers 18-pin PDIP, 18-pin SOIC, 20-pin TSSOP MCP2515 2.7 to 5.5 -40 to +125 3 2 6 2 Yes MCP2510 pin compatible upgrade with enhanced features including higher throughput and data byte filtering 18-pin PDIP, 18-pin SOIC, 20-pin TSSOP MCP25020 2.7 to 5.5 -40 to +125 3 2 2 1 N/A CAN 2.0B Active I/O Expander, Configurable I/O, 2 PWM outputs 14-pin PDIP, 14-pin SOIC 14-pin PDIP, 14-pin SOIC Part # Unique Features Packages MCP25025 2.7 to 5.5 -40 to +85 3 2 2 1 N/A CAN 2.0B Active I/O Expander, Configurable I/O, 2 PWM outputs, One-wire CAN option MCP25050 2.7 to 5.5 -40 to +125 3 2 2 1 N/A Mixed-Signal CAN 2.0B Active I/O Expander, Configurable I/O, 4 10-bit ADCs, 2 PWM outputs 14-pin PDIP, 14-pin SOIC MCP25055 2.7 to 5.5 -40 to +85 3 2 2 1 N/A Mixed-Signal CAN 2.0B Active I/O Expander, Configurable I/O, 4 10-bit ADCs, 2 PWM outputs, One-wire CAN option 14-pin PDIP, 14-pin SOIC MCP2551 4.5 to 5.5 -40 to +125 n/a n/a n/a n/a N/A High-speed CAN Transceiver (1 Mbps max. CAN bus speed), ISO11898 compatible, Industry standard pinout 8-pin PDIP, 8-pin SOIC Note 1: Not recommended for new designs. INTERFACE - Infrared Products Part # Operating Voltage (V) Operating Temperature Range (C) Max. Baud Rate (Kbaud) Unique Features MCP2120 2.5 to 5.5 -40 to +85 325 MCP2122 1.8 to 5.5 -40 to +85 16x less than clock input MCP2140A 2.0 to 5.5 -40 to +85 9.6 MCP2150 3.0 to 5.5 -40 to +85 115.2 Packages UART to IR encoder/decoder with both hardware and software baud rate selection 14-pin PDIP, 14-pin SOIC UART to IR encoder/decoder 8-pin PDIP, 8-pin SOIC IrDA(R) Standard protocol handler plus bit encoder/decoder, Fixed baud rate, Low-cost 18-pin PDIP, 18-pin SOIC, 20-pin SSOP IrDA(R) Standard protocol handler plus bit encoder/decoder on one chip for DTE applications, Programmable ID 18-pin PDIP, 18-pin SOIC, 20-pin SSOP (R) MCP2155 3.0 to 5.5 -40 to +85 IrDA Standard protocol handler plus bit encoder/decoder on one chip for DCE applications, Programmable ID 115.2 18-pin PDIP, 18-pin SOIC, 20-pin SSOP (R) IrDA is a registered trademark of Infrared Data Association INTERFACE - Ethernet Products Part # ENC28J60 ENC424J600 ENC624J600 Operating Voltage (V) Operating Temperature Range (C) MAC PHY TX/RX RAM 3.1 to 3.6 -40 to +85 Yes 10Base-T 8 KB SPI - 10Base-T Ethernet controller, IEEE 802.3TM compliant - Loopback test modes, Auto-polarity detection - Clock out pin with programmable frequencies 28-pin SOIC, 28-pin SSOP, 28-pin 6x6 QFN, 28-pin SPDIP 24 KB - SPI - 8-bit multiplexed parallel interface - 10/100 Ethernet controller, IEEE 802.3(TM) compliant Cryptographic Security Engines - MD5, SHA-1, AES, RSA Preprogrammed unique MAC address Loopback test modes, Auto-polarity detection Clock out pin with programmable frequencies 44-pin TQFP, 44-pin QFN 24 KB - SPI - 8-bit or 16-bit multiplexed or demultiplexed parallel interface - 10/100 Ethernet controller, IEEE 802.3(TM) compliant Cryptographic Security Engines - MD5, SHA-1, AES, RSA Preprogrammed unique MAC address Loopback test modes, Auto-polarity detection Clock out pin with programmable frequencies 64-pin TQFP 3.0 to 3.6 3.0 to 3.6 -40 to +85 -40 to +85 Yes Yes 10/100Base-T 10/100Base-T Interface Features Packages INTERFACE - Passive Access Products Part # MCP2030 Operating Voltage (V) Operating Temperature Range (C) Bus Type RF Carrier Frequency Data Format 1.8 to 3.6 -40 to +85 SPI 125 kHz NRZ Features Packages Three axis signal conditioning devices for passive access applications, High-sensitivity, Configurable smart wake-up filter 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP Analog and Interface Product Selector Guide 24 INTERFACE - LIN Transceiver Products Part # Description MCP201 LIN Transceiver with integrated VREG MCP2003 Stand-Alone LIN Transceiver (industry standard pinout) MCP2004 Stand-Alone LIN Transceiver with TXE/Fault I/O MCP2021 MCP2022 VREG Output Voltage (V) Operating Temperature Range (C) VREG Output Current (mA) Vcc Range (V) Max Baud Rate 5.0 5% -40 to +125 50 6 to 18(1) 20 Kbaud Revision 1.2 8-pin PDIP, 8-pin SOIC, 8-pin 6x5 DFN 20 Kbaud Revision 1.3, 2.0, 2.1, SAE J2602 8-pin PDIP, 8-pin SOIC, 8-pin 4x4 DFN 8-pin PDIP, 8-pin SOIC, 8-pin4x4 DFN None -40 to +125 None 6 to 27 (1) LIN Specification Supported Packages None -40 to +125 None 6 to 27(1) 20 Kbaud Revision 1.3, 2.0, 2.1, SAE J2602 LIN Transceiver with integrated VREG 5.0 3% 3.3 3% -40 to +125 50 6 to 18(1) 20 Kbaud Revision 1.3, 2.0, 2.1, SAE J2602 8-pin PDIP, 8-pin SOIC, 8-pin 6x5 DFN, 8-pin 6x5 DFN LIN Transceiver with integrated VREG, RESET pin 5.0 3% 3.3 3% -40 to +125 50 6 to 18(1) 20 Kbaud Revision 1.3, 2.0, 2.1, SAE J2602 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP Note 1: Can withstand 40V load dump. INTERFACE - Serial Peripherals Description Operating Voltage (V) Operating Temperature Range (C) Bus Type MCP23008 8-bit I/O Port Expander 1.8 to 5.5 -40 to +85 I2CTM 1700 3 HW address pins, HW interrupt, 25 mA source/sink capability per I/O 18-pin PDIP, 18-pin SOIC, 20-pin SSOP, 20-pin 4x4 QFN MCP23S08 8-bit I/O Port Expander 1.8 to 5.5 -40 to +85 SPI 10000 2 HW address pins, HW interrupt, 25 mA source/sink capability per I/O 18-pin PDIP, 18-pin SOIC, 20-pin SSOP, 20-pin 4x4 QFN I CTM 3400 1 HW address pin, HW interrupt, 25 mA source/sink per I/O, 100 kHz, 400 kHz and 3.4 MHz I2CTM supported 18-pin PDIP, 18-pin SOIC, 20-pin SSOP Part # MCP23009 8-bit I/O Port Expander 1.8 to 5.5 -40 to +125 Max. Bus Frequency (kHz) 2 Features Packages MCP23S09 8-bit I/O Port Expander 1.8 to 5.5 -40 to +125 SPI 10000 HW interrupt, 25 mA source/sink per I/O 18-pin PDIP, 18-pin SOIC MCP23016 16-bit I/O Port Expander 2.0 to 5.5 -40 to +85 I2CTM 400 3 HW address inputs, HW interrupt, 25 mA source/sink capability per I/O 28-pin PDIP, 28-pin SOIC, 28-pin SSOP, 28-pin 6x6 QFN MCP23017 16-bit I/O Expander 1.8 to 5.5 -40 to +125 I2CTM 1700 3 HW address pins, 25 mA sink/source per I/O, 100 kHz, 400 kHz and 3-4 MHz I2CTM supported, Interrupt output 28-pin PDIP, 28-pin SOIC, 28-pin SSOP, 28-pin QFN MCP23S17 16-bit I/O Expander 1.8 to 5.5 -40 to +125 SPI 10000 3 HW address pins, 25 mA sink/source per I/O, Interrupt output 28-pin PDIP, 28-pin SOIC, 28-pin SSOP, 28-pin QFN 2 24-pin SSOP, 28-pin SOIC, 28-pin SDIP 28-pin SOIC, 28-pin SDIP MCP23018 16-bit I/O Port Expander 1.8 to 5.5 -40 to +125 I CTM 3400 1 HW address pin, 2 HW interrupts, 25 mA source/sink per I/O, 100 kHz, 400 kHz and 3.4 MHz I2CTM supported MCP23S18 16-bit I/O Port Expander 1.8 to 5.5 -40 to +125 SPI 10000 2 HW interrupts, 25 mA source/sink per I/O INTERFACE - IEEE 802.15.4 ZigBee(R) RF Transceiver Products Part # Frequency Range (GHz) Power Output (dBm) Sensitivity (dBm) RSSI TX Power Consumption (mA) RX Power Consumption (mA) Clock (MHz) Sleep MAC MAC Features Encryption Interface Pin Count Packages MRF24J40 2.405-2.48 -95 0 Yes 18 22 20 Yes Yes CSMA-CA AES128 4-wire SPI 40 40-pin QFN MRF24J40MA 2.405-2.48 -95 0 Yes 23 19 20 Yes Yes CSMA-CA AES128 4-wire SPI 12 Module 2.405-2.48 -102 20 Yes 120 25 20 Yes Yes CSMA-CA AES128 4-wire SPI 12 Module 433/868/915 -110 7 Yes 15 11 - Yes - - - 4-wire SPI 16 16-pin TSSOP MRF24J40MB MRF49XA INTERFACE - Stand-alone RF Receiver Products Modulation Data Rate (kbps) Frequency Range (MHz) rfRXD0420 ASK, FSK, FM 80 rfRXD0920 ASK, FSK, FM 80 Part # Sensitivity (dBm) IF Frequency Range (MHz) Operating Voltage (V) RSSI Selectable LNA Gain 300 to 450 -111 0.455 to 21.4 2.5 to 5.5 Yes Yes 32-pin LQFP 800 to 930 -109 0.455 to 21.4 2.5 to 5.5 Yes Yes 32-pin LQFP Packages INTERFACE - USB Products Part # MCP2200 USB Speed USB Compliant PHY MCU Interface Tx/Rx Buffer Size (bytes) Number of GPIO Operating Voltage (V) Full-Speed USB (12 Mb/s), Low-Speed USB (1.5 Mb/s) Yes Yes UART 128/128 8 2.7 to 5.5 Packages 20-pin SOIC, 20-pin TSSOP, 20-pin QFN Analog and Interface Product Selector Guide 25 SAFETY & SECURITY SAFETY & SECURITY - Photoelectric Smoke Detector ICs Part # Horn Driver Alarm Pattern Alarm Memory Low Battery Detection Chamber Test Alarm Interconnect Sensitivity Timer Internal POR Alternate Diagnostic Mode Operating Temperature Range (C) Packages RE46C140 NFPA Temporal No Yes Yes Yes Yes Yes - -25 to +75 16-pin PDIP, 16-pin SOIC RE46C141 NFPA Temporal No Yes Yes Yes - Yes - -25 to +75 16-pin PDIP, 16-pin SOIC RE46C143 Continuous Tone No Yes Yes Yes - Yes - -25 to +75 16-pin PDIP, 16-pin SOIC RE46C144 Continuous Tone No Yes Yes Yes Yes Yes - -25 to +75 16-pin PDIP, 16-pin SOIC RE46C145 NFPA Temporal No Yes Yes Yes Yes Yes Yes -25 to +75 16-pin PDIP, 16-pin SOIC RE46C165 NFPA Temporal Yes Yes Yes Yes Yes Yes Yes -25 to +75 16-pin PDIP, 16-pin SOIC 16-pin PDIP, 16-pin SOIC RE46C166 Continuous Tone Yes Yes Yes Yes Yes Yes Yes -25 to +75 RE46C167 NFPA Temporal Yes Yes Yes Yes Yes Yes Yes -25 to +75 16-pin PDIP, 16-pin SOIC RE46C168 Continuous Tone Yes Yes Yes Yes Yes Yes Yes -25 to +75 16-pin PDIP, 16-pin SOIC RE46C190 NFPA Temporal or Continuous Tone No Yes Yes Yes Yes Yes - -10 to +60 16-pin SOIC SAFETY & SECURITY - Ionization Smoke Detector ICs Horn Driver Alarm Pattern Alarm Memory Low Battery Detection Reverse Battery Protection Alarm Interconnect Hush Timer Power-up Low Battery Test Operating Temperature Range (C) RE46C120 NFPA Temporal or Continuous Tone No Yes RE46C121 NFPA Temporal No Yes Yes - - - -10 to +60 16-pin PDIP Yes Yes - - -10 to +60 RE46C122 NFPA Temporal No 16-pin PDIP Yes Yes Yes Yes Yes -10 to +60 RE46C126 Continuous Tone 16-pin PDIP No Yes Yes Yes - - -10 to +60 RE46C127 16-pin PDIP Continuous Tone No Yes Yes Yes Yes Yes -10 to +60 16-pin PDIP RE46C128 NFPA Temporal No Yes Yes Yes - Yes -10 to +60 16-pin PDIP RE46C129 Continuous Tone No Yes Yes Yes - Yes -10 to +60 16-pin PDIP RE46C152 NFPA Temporal or Continuous Tone No Yes Yes Yes Yes Yes -10 to +60 16-pin PDIP RE46C162 NFPA Temporal or Continuous Tone Yes Yes Yes Yes Yes Yes -10 to +60 16-pin PDIP RE46C163 NFPA Temporal or Continuous Tone Yes Yes Yes Yes Yes Yes -10 to +60 16-pin PDIP RE46C180 NFPA Temporal or Continuous Tone Yes Yes No Yes Yes Yes -10 to +60 16-pin PDIP, 16-pin SOIC Part # Packages SAFETY & SECURITY - Ionization Smoke Detector Front Ends Microprocessor Compatible Output Output Options Typical Application Operating Temperature Range (C) RE46C112 Part # Yes VOUT 1/4 of VDD or VOUT 1/4 of Detect Input 3V or 3.3V Microprocessor -10 to +60 8-pin PDIP Packages RE46C114 Yes VOUT 1/2 of VDD or VOUT 1/2 of Detect Input 5V Microprocessor -10 to +60 8-pin PDIP SAFETY & SECURITY - Piezoelectric Horn Drivers Operating Voltage (V) Piezoelectric Horn Driver LED Driver Voltage Regulator (V) Low Battery Detection Interconnect Power good Operating Temperature Range (C) RE46C100 6 to 16 RE46C101 6 to 16 Yes - - - - - -40 to +85 8-pin PDIP, 8-pin SOIC Yes Yes - - - - -40 to +85 RE46C104 8-pin PDIP, 8-pin SOIC 4 to 8 Yes - - - - - 0 to +50 RE46C105 14-pin PDIP, 14-pin SOIC 6 to 12 Yes Yes 3.3 or 5 Yes - - -40 to +85 14-pin PDIP, 14-pin SOIC RE46C107 2 to 5 Yes Yes 3 or 3.3 Yes - - 0 to +50 16-pin PDIP, 16-pin SOIC RE46C108 6 to 12 Yes - 3.3 or 5 - - - -40 to +85 8-pin PDIP, 8-pin SOIC RE46C109 6 to 12 Yes - 3 Yes Yes Yes -40 to +85 16-pin PDIP, 16-pin SOIC RE46C117 2 to 5 Yes - - - - - 0 to +50 RE46C119 6 to 12 Yes - 3 Yes Yes Yes -40 to +85 Part # Packages 8-pin PDIP, 8-pin SOIC 16-pin PDIP, 16-pin SOIC Analog and Interface Product Selector Guide 26 ANALOG DESIGN DEVELOPMENT TOOLS Evaluation, Demonstration and Development Kits Order # Description Devices Supported Thermal Management Demonstration and Evaluation Tools TMPSNS-RTD1 PT100 RTD Evaluation Board MCP6S26, MCP3301, MCP6024, MCP41010, PIC18F2550, TC1071, MCP6002 MCP9700DM-PCTL MCP9700 Temperature-to-Voltage Converter PICtailTM Demonstration Board MCP9800 MCP9700DM-TH1 MCP9700 Thermistor Demonstration Board MCP9700, MCP6S92 MCP9800DM-PCTL MCP9800 Temperature Sensor PICtailTM Demonstration Board MCP9800 MCP9800DM-TS1 MCP9800 Temperature Sensor Demonstration Board MCP9800 MCP9800DM-DL MCP9800 Temperature Data Logger Demonstration Board MCP9800 MCP9800DM-DL2 MCP9800 Temperature Data Logger Demonstration Board 2 MCP9800, MCP101, PIC10F202, 24LC16B TC72DM-PICTL TC72 Digital Temperature Sensor PICtailTM Demonstration Board TC72 TC74DEMO TC74 Serial Digital Thermal Sensor Demonstration Board TC74 TC77DM-PICTL TC77 Thermal Sensor PICtailTM Demonstration Board TC77 TC642DEMO TC64X/64XB Fan Speed Controller Demonstration Board TC642, TC646, TC647, TC648, TC649 TC650DEMO TC650 Fan Controller Demonstration Board TC650 TC652DEMO TC652 Fan Controller Demonstration Board TC652 TC1047ADM-PICTL TC1047A Temperature-to-Voltage Converter PICtailTM Demonstration Board TC1047A TMPSNSRD-TCPL1 Thermocouple Reference Design MCP9804, MCP3421 TMPSNSRD-RTD2 RTD Reference Design Board MCP3551, MCP9804 Mixed Signal Demonstration and Evaluation Tools ADM00333 PIC18F87J72 Evaluation Board PIC18F87J72 ARD00280 PIC18F87J72 Single Phase Energy Meter Reference Design n/a ARD00330 PIC18F87J72 Energy Monitoring PICtail Plus Daughter Board n/a DV3201A MCP3XXX Single/Dual ADC MXDEV(R) Daughter Board MCP3001, MCP3002, MCP3201, MCP3202 DV3204A MCP3204/08 MXDEV(R) Daughter Board MCP3004, MCP3008, MCP3204, MCP3208 MCP2030DM-TPR MCP2030 Bidirectional Communications Demonstration Kit MCP2030, MCP3421, PIC16F636, TC4421, PIC18F4680 MCP3421EV MCP3421 SOT-23-6 Evaluation Board MCP3421 MCP3421DM-BFG MCP3421 Battery Fuel Gauge Demo Board MCP3421, MCP73831, MCP1702, PIC18F4550 MCP3422EV MCP3422 Evaluation Board MCP3422 MCP3423EV MCP3423 Evaluation Board MCP3423 MCP3424EV MCP3424 Evaluation Board MCP3424 MCP3425EV MCP3425 SOT 23-6 Evaluation Board MCP3425 MCP3221DM-PCTL MCP3221 PICtailTM Demonstration Board MCP3221 MCP3551DM-PCTL MCP3551 Delta-Sigma ADC Demonstration Board MCP3551 MCP355XDV-MS1 MCP355X Sensor Application Developer's Board MCP3551, MCP3553, MCP3550-50, MCP3550-60 MCP355XDM-TAS MCP355X Tiny Application Sensor Demonstration Board MCP3551, MCP3553, MCP3550-50, MCP3550-60 MCP3901EV-MCU16 MCP3901 ADC Evaluation Board for 16-bit MCUs MCP3901, PIC24F, PIC24H, dsPIC33, PIC18F86J55 MCP3905EV MCP3905 Energy Meter Evaluation Board MCP3905 MCP3905RD-PM1 MCP3905 Energy Meter Reference Design MCP3905 MCP3909EV-MCU16 MCP3909 ADC Evaluation Board for 16-bit MCUs MCP3909 MCP3909RD-3PH1 MCP3909 3-Phase Energy Meter Reference Design MCP3909, PIC18F2520, PIC18F4550 MCP3909RD-3PH3 MCP3909 and dsPIC33F 3-Phase Energy Meter Reference Design MCP3909, dsPIC33FJ128GP706 MCP3909RD-PM1 MCP3909 and PIC18F25K20 Low Cost Power Monitor Reference Design MCP3909, PIC18F25K20 MCP3909RD-1PH1 MCP3909 and PIC18F85J90 Single Phase Energy Meter Reference Design MCP3909, PIC18F85J90 MCP401XEV MCP401X Evaluation Board MCP40D18, MCP4017, MCP4018, MCP4019, MCP40D17, MCP40D19 Analog and Interface Product Selector Guide 27 ANALOG DESIGN DEVELOPMENT TOOLS Evaluation, Demonstration and Development Kits Order # Description Devices Supported Mixed Signal Demonstration and Evaluation Tools (Continued) MCP3421DM-WS1 MCP3421 Weight Scale Demo Board MCP3421, MCP6V07, PIC18F4550 MCP402XEV MCP402X Non-Volatile Digital Potentiometer Evaluation Board MCP4021, MCP4022, MCP4023, MCP4024 MCP42XXEV MCP42XX Evaluation Board MCP4231, MCP4241, MCP4251, MCP4261 MCP43XXEV MCP43XX Evaluation Board MCP4331, MCP4341, MCP4351, MCP4361 MCP4XXXDM-DB MCP4XXX Digital Potentiometer Daughter Board MCP4011, MCP4021, MCP42XXX MCP42XXDM-PTPLS MCP42XX PICtailTM Plus Daughter Board MCP4231, MCP4232, MCP4241, MCP4242, MCP4251, MCP4252, MCP4261, MCP4262 MCP46XXDM-PTPLS MCP46XX PICtailTM Plus Daughter Board MCP4631, MCP4641, MCP4651, MCP47652, MCP4661, MCP4662 MCP46XXEV MCP46XX Evaluation Board MCP4631, MCP4641, MCP4651, MCP4661 MCP4725EV MCP4725 SOT 23-6 Evaluation Board MCP4725 MCP4725DM-PTPLS MCP4725 PICtailTM Plus Daughter Board MCP4725 MCP4728EV MCP4728 Quad DAC Evaluation Board MCP4728 ADM00310 MCP3903 ADC Evaluation Board for 16-bit MCUs MCP3903, MCP2200, PIC24, dsPIC33 DV42XXX MCP42XXX Digital Potentiometer Evaluation Board MCP42010, MCP42050, MCP42100 DVMCPA MXDEV(R) Analog Evaluation System MCP3001/02, MCP3004/08, MCP3201/08, MCP3204/08 MXSIGDM Mixed Signal PICtailTM Demonstration Board TC132X, MCP330X, MCP320X, MCP482X, MCP492X, MCP3221, MCP3021, MCP1525 Power Management Demonstration and Evaluation Tools MCP1252DM-BKLT MCP1252 Charge Pump Backlight Demonstration Board MCP1252 MCP1256/7/8/9EV MCP1256/7/8/9 Charge Pump Evaluation Board MCP1256, MCP1257, MCP1258, MCP1259 MCP1601EV MCP1601 Buck Regulator Evaluation Board MCP1601 MCP1602EV MCP1602 Evaluation Board MCP1602 MCP1603EV MCP1603 Buck Converter Evaluation Board MCP1603 MCP1603RD-TNY MCP1603 Tiny Reference Design MCP1603 MCP1612EV MCP1612 Synchronous Buck Regulator Evaluation Board MCP1612 MCP1630RD-DDBK1 MCP1630 +12V in Dual Output Buck Converter Reference Design MCP1630 MCP1630RD-DDBK3 MCP1630 Bidirectional 4-Cell Li-Ion Charger Reference Design MCP1630V, PIC16F88, MCP6022 MCP1630RD-NMC1 MCP1630, PIC12F683, MCP6292, MCP1702 MCP1630 Low-Cost NiMH Battery Charger Reference Design MCP1630DM-DDBK1 MCP1630 1A Bias Supply Demonstration Board MCP1630 MCP1630DM-DDBS1 MCP1630 Automotive Input Boost Converter Demonstration Board MCP1630, PIC12F683 MCP1630DM-LED2 MCP1630 Boost Mode LED Driver Demonstration Board MCP1630V, PIC12F683, MCP1702 MCP1630RD-LIC1 MCP1630 Li-Ion Multi Bay Battery Charger Reference Design MCP1630 MCP1630RD-LIC2 MCP1630 Low Cost Li-Ion Battery Charger Reference Design MCP1630 MCP1630DM-NMC1 MCP1630 NiMH Battery Charger Demonstration Board MCP1630 MCP1630DM-DDBS2 MCP1630 Coupled Inductor Boost Demonstration Board MCP1630, PIC12F683 MCP1630DM-DDBK4 MCP1630 Automotive Input, Triple Output Converter Demonstration Board MCP1630, PIC12F683 MCP1631RD-DCPC1 MCP1631HV Digitally Controlled Programmable Current Source Reference Design MCP1631HV, PIC16F616 MCP1631RD-MCC1 MCP1631HV Multi-Chemistry Battery Charger Reference Design MCP1631HV, PIC16F883 MCP1631RD-MCC2 MCP1631HV Multi-Chemistry Battery Charger Reference Design MCP1631HV, PIC16F883 MCP1640EV-SBC MCP1640 Sync Boost Converter Evaluation Board MCP1640 MCP1640RD-4ABC MCP1640 Single Quad-A Battery Boost Converter Reference Design MCP1640, PIC12F617 28 Analog and Interface Product Selector Guide ANALOG DESIGN DEVELOPMENT TOOLS Evaluation, Demonstration and Development Kits Order # Description Devices Supported Power Management Demonstration and Evaluation Tools (Continued) MCP1650DM-LED1 MCP1650 3W White LED Demonstration Board MCP1650 MCP1650DM-LED2 MCP1650 Multiple White LED Demonstration Board MCP1650 MCP1650EV MCP1650 Boost Controller Evaluation Board MCP1650 MCP1650DM-DDSC1 MCP1650 SEPIC Power Supply Demonstration Board MCP1650 MCP1726EV MCP1726 1A LDO Evaluation Board MCP1726 MCP73113EV-1SOVP MCP73113 OVP Single Cell Li-Ion Battery Charger Evaluation Board MCP73113, MCP73114 MCP73213EV-2SOVP MCP73213 OVP Dual Cell Li-Ion Battery Charger Evaluation Board MCP73213 MCP73X23EV-LFP MCP73X23 OVP Lithium Iron Phosphate Battery Charger Evaluation Board MCP73123, MCP73223 MCP73871DM-VPCC MCP73871 Demo Board with Voltage Proportional Current Control MCP73871 MCP7381XEV MCP7381X Low-Cost Li-Ion Battery Charger Evaluation Board MCP73811, MCP73812 MCP7382XEV MCP7382X Li-Ion Battery Charger Evaluation Board MCP7382X MCP73831EV MCP73831 Evaluation Kit MCP73831 MCP73833EV MCP73833 Li-Ion Battery Charger Evaluation Board MCP73833, MCP73834 MCP7383XEV-DIBC MCP73837/8 AC/USB Dual Input Battery Charger Evaluation Board MCP73837, MCP73838 MCP7383XRD-PPM MCP7383X Li-Ion System Power Path Management Reference Design MCP73831, MCP73832, MCP73833, MCP73834 MCP7384XEV MCP7384X Li-Ion Battery Charger Evaluation Board MCP7384X MCP73855EV MCP73855 Li-Ion Battery Charger Evaluation Board MCP73855 MCP7386XEV MCP7386X Li-Ion Battery Charger Evaluation Board MCP7386X MCP73871EV MCP73871 Evaluation Board MCP73871 SOT23-3EV-VREG SOT23-3 Voltage Regulator Evaluation Board MCP1701A, MCP1702, MCP1703 SOT223-3EV-VREG SOT223-3 Voltage Regulator Evaluation Board MCP1791, MCP1824, MCP1825, MCP1826 SOT89-3EV-VREG SOT89-3 Voltage Regulator Evaluation Board MCP1700, MCP1701A, MCP1702, MCP1703 TO263-3EV-VREG TO220-3/TO263-3 Voltage Regulator Evaluation Board MCP1790, MCP1825S, MCP1826S, MCP1827S SOT23-5EV-VREG SOT23-5 Voltage Regulator Evaluation Board MCP1801, MCP1802, TC1014/1015/1185, and other SOT23-5 LDOs SOT223-5EV-VREG SOT223-5 Voltage Regulator Evaluation Board MCP1790, MCP1824, MCP1825, MCP1826 TO263-5EV-VREG TO220-5/TO263-5 Voltage Regulator Evaluation Board MCP1790, MCP1791, MCP1825, MCP1826, MCP1827 TC110DM TC110 Boost Converter Demonstration Board TC110, MCP73832 TC115EV TC115 PFM/PWM Boost Converter Evaluation Board TC115 TC1016/17EV TC1016/17 LDO Linear Regulator Evaluation Board TC1016/17 TC1303BDM-DDBK1 TC1303B Demonstration Board TC1303B TC1303DM-DDBK2 TC1303 DFN Adjustable Output Demonstration Board TC1303C Interface Products Demonstration and Evaluation Tools GPIODM-KPLCD GPIO Expander Keypad and LCD Demo Board MCP23008, MCP23S08, MCP23017, MCP23S17, PIC18F4550, MCP1702 DV251001 MCP2510/2515 CAN Developer's Kit MCP2515, MCP2510 DV250501 MCP250XX CAN I/O Expanders Developer's Kit MCP25020, MCP25025, MCP25050, MCP25055 MCP2515DM-PCTL MCP2515 CAN Controller PICtailTM Demonstration Board MCP2515 MCP215XDM MCP215X Data Logger Demonstration Board MCP2150/55 MCP2140DM-TMPSNS MCP2140 IrDA(R) Wireless Temp Demonstration Board MCP2140 MCP212XDM MCP2120/22 Developer's Board MCP2120, MCP2122 MCP212XEV-DB MCP212X Developer's Daughter Board MCP212X Analog and Interface Product Selector Guide 29 ANALOG DESIGN DEVELOPMENT TOOLS Evaluation, Demonstration and Development Kits Order # Description Devices Supported Interface Products Demonstration and Evaluation Tools (Continued) MCP215X/40EV-DB MCP215X/40 Developer's Daughter Board MCP2140, MCP2150/55 MCP2150DM MCP2150 Developer's Board MCP2150, MCP2155 MCP2200EV-VCP MCP2200 USB to RS232 Demonstration Board MCP2200 MCP23X08EV MCP23X08 8-bit GPIO Expander Evaluation Board MCP23008, MCP23S08 MCP23X17EV MCP23X17 16-bit GPIO Expander Evaluation Board MCP23017, MCP23S17 MCP2515DM-BM MCP2515 CAN Bus Monitor Demonstration Board MCP2515, MCP2551 MCP2515DM-PTPLS MCP2515 PICtailTM Plus Daughter Board MCP2515, MCP2551 PKSERIAL-SPI1 PICkitTM Serial SPI Demonstration Board 25LC020A, TC77, MCP3201, MCP4822, MCP41010, MCP6S92, MCP23S08 PKSERIAL-I2C1 PICkitTM Serial I2CTM Demonstration Board 24LC02B, MCP9801, MCP3221, TC1321, MCP23008 Linear Demonstration and Evaluation Tools MCP6031DM-PTPLS MCP6031 Photodiode PICtailTM Plus Demonstration Board MCP6031 MCP651EV-VOS MCP651 Input Offset Evaluation Board MCP651 MCP661DM-LD MCP661 Line Driver Demo Board MCP661, MCP662, MCP665 MCP6S22DM-PICTL MCP6S22 PGA PICtailTM Demonstration Board MCP6S22 MCP6S2XEV MCP6S2X PGA Evaluation Board MCP6S2X MCP6SX2DM-PCTLPD MCP6SX2 PGA Photodiode PICtailTM Demonstration Board MCP6S22/92 MCP6SX2DM-PCTLTH MCP6SX2 PGA Thermistor PICtailTM Demonstration Board MCP6S22/92 MCP6V01DM-VOS MCP6V01 Input Offset Demonstration Board MCP6V01, MCP6V03, MCP6V06, MCP6V08 MCP6V01RD-TCPL MCP6V01 Thermocouple Auto-Zeroed Reference Design MCP6V01 PIC16F690DM-PCTLHS Humidity Sensor PICtailTM Demonstration Board MCP6291, PIC16F690 MCP6XXXEV-AMP1 MCP6XXX Amplifier Evaluation Board 1 MCP6021 MCP6XXXEV-AMP2 MCP6XXX Amplifier Evaluation Board 2 MCP6021 MCP6XXXEV-AMP3 MCP6XXX Amplifier Evaluation Board 3 MCP6021 MCP6XXXEV-AMP4 MCP6XXX Amplifier Evaluation Board 4 MCP6021 MCP6XXXDM-FLTR Active Filter Demonstration Board Kit MCP6271 Analog Blank Evaluation Boards VSUPEV SOT-23-3 Voltage Supervisor Evaluation Board SOT-23-3 Devices VSUPEV2 SOT-23-5/6 Voltage Supervisor Evaluation Board SOT-23-5, SOT-23-6 Devices SC70EV SC70-6 and SOT-23-6/8 to DIP-8 Evaluation Board SC70-6/5/3, SOT-23-8/6/5/3, and DIP-8 Devices SOIC8EV SOIC/MSOP/TSSOP/DIP 8-pin Evaluation Board 8-pin SOIC, MSOP, TSSOP, DIP Devices SOIC14EV SOIC/TSSOP/DIP 14-pin Evaluation Board 14-pin SOIC, TSSOP, DIP Devices TSSOP20EV 20-pin TSSOP and SSOP Evaluation Board TSSOP-20/16/14/8 and SSOP-20 Miscellaneous Analog Demonstration and Evaluation Tools ADM00344 RE46C190 Demonstration Board RE46C190 EFIELDEV Electrical Field Evaluation Board N/A HFIELDEV Magnetic Field Evaluation Board N/A INTRFCEV PSRR and Digital Noise Evaluation Board N/A 30 Analog and Interface Product Selector Guide FEATURED ANALOG DEVELOPMENT TOOLS Thermal Management Products MCP9700 Thermistor Demo Board (MCP9700DM-TH1) The MCP9700 Thermistor Demo Board contains the analog circuitry to measure temperature. The board uses BC Components' 232264055103 NTC thermistor to convert temperature to resistance. The thermistor is placed in a voltage divider which converts resistance to voltage. This voltage is filtered and placed at the MCP6S22 Programmable Gain Amplifier's (PGA) CH0 input. The PGA gains and buffers the thermistor. PT100 RTD Evaluation Board (TMPSNS-RTD1) TThis board demonstrates how to bias a Resistive Temperature Detector (RTD) and accurately measure temperature. Up to two RTDs can be connected. The RTDs are biased using constant current source and the output voltage is scaled using a differential amplifier. The output is then connected to a 12-bit differential Analog-to-Digital Converter (ADC) MCP3301. The ADC outputs serial data to a PIC18F2550 device using a Serial Peripheral Interface (SPI). The data is transmitted to a PC using a USB interface. A Microsoft Excel(R) macro is used as a Graphical User Interface (GUI) to acquire the data. The acquired data is stored in an Excel worksheet and graphed as a real-time strip chart display. MCP9800 Temperature Data Logger Demo Board (MCP9800DM-DL) A Allows users to store up to 128,000 ttemperature readings from the MCP9800 sensor to the 24LC1025, Microchip's 1024 Kbit EEPROM. A PIC16F684 MCU communicates with the sensor d EEPROM d and EEPROM. IIn addition, the PIC MCU interfaces to a PC using the PICkitTM 1 Flash Starter Kit and transfers the temperature readings from the EEPROM to the PC. Microsoft Excel(R) can be used to view the data. Mixed Signal Products MCP3909 and PIC18F85J90 Single Phase Energy Meter Reference Design (MCP3909RD-1PH1) The MCP3909/PIC18F85J90 Single Phase Energy Meter Reference Design is a fully function single phase meter. The design is intended to be low cost and is transformerless. The design uses a half-wave rectified power supply circuit and a shunt current sensing element. A single MCP3909 acts as the analog front end measurement circuitry. The PIC18F85J90 directly drives the LCD glass and displays active energy consumption. MCP3421 Battery Fuel Gauge Demo Board (MCP3421DM-BFG) This board is used to demonstrate the MCP3421 18-bit delta-sigma ADC for battery fuel gauging applications. It includes two MCP3421 devices, MCP73831 ((single i l cell Li-Ion/Li-Polymer Charger) and PIC18F4550 MCU. The board measures: (1) the battery voltage and (2) the current coming out from the battery in the discharging mode and into the battery in the charging mode using the ADC device (if charging mode is enabled (optional)). It calculates the total fuel used and also fuel remaining. MCP4725 PICtail Plus Daughter Board (MCP4725DM-PTPLS) This daughter board demonstrates the MCP4725 (12 bit DAC with non-volatile memory) features using the Explorer 16 Development Board and the PICkit Serial Analyzer. MCP42XX PICtail Plus Daughter Board (MCP42XXDM-PTPLS) The MCP42XX PICtail Plus Daughter Board is used to demonstrate the operation of the MCP42XX Digital Potentiometers. The operation of the MCP41XX devices is similar to the MCP42XX devices. Therefore, this demo board can be used as a development platform for either device family. This board is designed to be used in conjunction with either the PIC24 Explorer 16 Demo Board or the PICkit Serial Analyzer. Power Management Products MCP1631HV Multi-Chemistry Battery Charger Reference Design (MCP1631RD-MCC1) This reference design is a complete stand-alone constant current battery charger for NiMH, NiCd or constant current/constant voltage for Li-Ion battery packs. When charging NiMH or NiCd batteries, the reference design is capable of charging one, one two, three or four batteries connected in series and one or two series batteries for Li-Ion. This board utilizes the MCP1631HV (high-speed PIC MCU PWM TSSOP-20) and PIC16F883 (28-pin SSOP). MCP73871 Demo Board with Voltage Proportional Current Control (MCP73871DM-VPCC) The MCP73871 Demo Board with Voltage Proportional Current Control is designed to demonstrate Microchip's stand-alone linear Li-Ion battery charger with system power path and load sharing management control l ti Th MCP73871 MC solution. The integrates the required elements to meet design challenges when developing new Li-Ion/ Li-Polymer battery powered products. Analog and Interface Product Selector Guide 31 FEATURED ANALOG DEVELOPMENT TOOLS MCP73X23 OVP Lithium Iron Phosphate Battery Charger Evaluation Board (MCP73X23EV-LFP) The MCP73X23 Lithium Iron Phosphate Battery Charger Evaluation board demonstrates the features of Microchip's MCP73123 and MCP73223 Lithium Iron Phosphate (LiFePO4) Battery Charge Management Controller with Input Overvoltage Protection. MCP7383X Li-Ion System Power Path Management Reference Design (MCP7383XRD-PPM) This reference design is developed to assist product designers in reducing product design cycle and time by utilizing Microchip's stand-alone Li-Ion battery charge management controllers with system power path management. Due to the natural characteristics of Li-Ion/Li-Polymer batteries, they are the most popular power sources for mobile devices, however, extra care in design is always important. System Power Path Management allows end-users to charge their batteries without interruption. MCP1640 Sync Boost Converter Evaluation Board (MCP1640EV-SBC) The T MCP1640 Synchronous Boost Converter Evaluation board demonstrates the MCP1640 in two boost-converter applications with multiple output voltages. It can be used to evaluate both package options (SOT-23-6 and 2x3-8 DFN). This board was developed to help engineers reduce the product design cycle time. t MCP1252 Charge Pump Backlight Demo Board (MCP1252DM-BKLT) The MCP1252 board demonstrates the use of a charge pump device in an LED application and acts as a platform to evaluate the MCP1252 device in general. Light intensity is controlled uniformly through the use of ballast resistors. A PIC10F206 MCU provides an enable signal to the MCP1252 and accepts a push-button input that allows the white LEDs to be adjusted to five different light intensities. Interface Products MCP2515 CAN Bus Monitor Demo Board (MCP2515DM-BM) The MCP2515 CAN Bus Monitor Demo board kit contains two identical boards which can be connected together to create a simple two node Controller Area Network (CAN) bus, which can be controlled and/ or monitored it d via i th the included PC interface. The board(s) can also be connected to an existing CAN bus. 32 Analog and Interface Product Selector Guide LIN Serial Analyzer (APGDT001) The LIN Serial Analyzer development system enables a Personal Computer (PC) to communicate with a LIN (Local Interface Network) bus. The PC program uses a graphical user interface to enter and display di l message frames occurring on the target bus. USB to UART Converter Evaluation Board (MCP2200EV-VCP) The USB to UART Converter Eval board allows users to store up to 128,000 temperature readings from the MCP9800 sensor to the 24LC1025, Microchip's 1024 Kbit EEPROM. A PIC16F684 MCU communicates with the sensor and EEPROM. In addition, the PIC MCU interfaces to a PC using the PICkit 1 Flash Starter Kit and transfers the temperature readings from the EEPROM to the PC. Microsoft Excel can be used to view the data. Linear Products MCP6V01 Thermocouple Auto-Zeroed Ref Design Board (MCP6V01RD-TCPL) The MCP6V01 design board demonstrates how to use a difference amplifier system to measure Electromotive Force (EMF) voltage at the cold junction of o thermocouple in order to accurately measure temperature of the thermocouple bead. This can be done by using the MCP6V01 auto-zeroed op amp because of its ultra low offset Voltage (VOS) and high Common Mode Rejection Ratio (CMRR). MCP651 Input Offset Evaluation Board (MCP651EV-VOS) The MCP651 Input Offset Evaluation board is intended to provide a simple means to measure the MCP651 Input Offset Evaluation Board op amp's input offset voltage under a variety of operating conditions. The measured input offset voltage (VOST) conditions includes the input offset voltage specified in the data sheet (VOS) plus changes due to: power supply voltage (PSRR), common mode voltage (CMRR), output voltage (AOL), input offset voltage drift over temperature (VOS/TA) and 1/f noise. MCP6271 Active Filter Eval Kit (MCP6XXXDM-FLTR) This kit supports active filters designed by FilterLab(R) V2.0. These filters are all pole and are built by cascading first and second order sections. The kit includes: one PCB designed to provide mid-supply biasing to the other printed circuit boards, four PCBs that support active filter designs with filter order between n = 1 and 8 (output test point for lab equipment provided) and op amps, zero ohm jumpers, resistors and capacitors that can be used to help build filters. ANALOG PRODUCT PART NUMBERS Part Number Suffix Designations Ordering Information for all Microchip Analog Products beginning with "TC" prefix (formerly TelCom Semiconductor Products) TC 7106 A-60 1 C P L 713 Taping Direction: TR or 713: Standard Taping, blank: no tape and reel Number of Package Pins (See specific data sheet) Package Type Operating Temperature Range: C: Commercial Range (0C to +70C) E: Extended Industrial Range (-40C to +85C) I: Industrial Range (-25C to +85C) M: Military Range (-55C to +125C) V: See Data Sheet for Specific Temperature Range (Extra Feature Code and/or Tolerance)* (See specific data sheet) (Output Voltage or Detect Voltage)* (If applicable, see specific data sheet) Electrical Performance Grade Option (Variation/Option)* (If applicable, see specific data sheet) A: Test Selection Criteria (See specific data sheet) B: R: Reversed Pin Layout Product Part Number (2 to 6 characters, see specific data sheet) Product Prefix NOTE: ( )* Used for voltage regulators and detectors. Package AB Description TO-220 # of Pins Package 3 MB SOT-89 Description # of Pins 3 AK TO-220 7 MF DFN (3x3) 8 AT TO-220 5 MT SOT-89 5 AV TO-220 (Formed) 5 NB SOT-23B 3 BB TO-220B 3 OA SOIC (N) 8 CB SOT-23A 3 OD SOIC (N) 14 CH SOT-23A 6 OE SOIC (W) 16 CT SOT-23A 5 OG SOIC (W) 24 DB SOT-223 3 OI SOIC (W) 28 EB DDPAK 3 OR SOIC (N) 16 EK DDPAK 7 PA PDIP (N) 8 ET DDPAK 5 PD PDIP (N) 14 HA SOP 8 PE PDIP (N) 16 JA CDIP (N) 8 PF PDIP (N) 24 JD CDIP (N) 14 PG PDIP (W) 24 JE CDIP (N) 16 PI PDIP (W) 28 JG CDIP (W) 24 PJ PDIP (W) 28 JI CDIP (W) 28 PL PDIP (W) 40 JL CDIP (W) 40 QR QSOP (N) 16 KU MQFP 64 RC SOT-143 4 KW MQFP 44 SI SSOP (W) 28 LB SC-70 3 UA MSOP 8 LI PLCC 28 UN MSOP 10 LS PLCC 68 VB DPAK 3 LT SC-70 5 ZB TO-92 3 LW PLCC 44 ZM TO-92 2 Analog and Interface Product Selector Guide 33 ANALOG PRODUCT PART NUMBERS Part Number Suffix Designations Ordering Information for all Microchip Analog Products beginning with "MCP" prefix MCP xxxxx T - yyy z h / qq Package Type (see table below) Operating Temperature Range: - blank: Commercial Range (0C to +70C) I: Industrial (-40C to +85C) E: Extended Industrial Range (-40C to +125C Supervisor Bond Options: D: F: H: blank: Not Applicable Reset Voltage Thresholds or Performance Grade Options: (1-3 characters, see specific data sheets) 270: 2.7V reset threshold 300: 3.0V reset threshold 315: 3.15V reset threshold 450: 4.5V reset threshold 460: 4.6V reset threshold 475: 4.7V reset threshold 485: 4.85V reset threshold or B: Grade (see specific data sheet) C: Grade (see specific data sheet) or blank: not applicable Tape and Reel: T: Tape and Reel blank: No Tape and Reel Product Part Number (3-6 characters, see specific data sheet) Product Prefix Package TO 34 Description TO-92 # of Pins Tube/Bag Qty. Reel Qty. 3 1000 n/a TT SOT-23 3 n/a 3000 OT SOT-23 5 n/a 3000 P PDIP 8 60 n/a SN SOIC 8 100 3300 ST TSSOP 8 100 2500 MS MSOP 8 100 2500 MF DFN (2x3) 8 n/a 3300 MF DFN (3x3) MF DFN (3x3, 10-Pin) 8 50 3300 10 120 3300 ST TSSOP 14 96 2500 P PDIP 14 30 n/a 2600 SL SOIC 14 57 P PDIP 18 25 n/a SO SOIC 18 42 1100 ST TSSOP 20 74 2500 SS SSOP 20 67 1600 ML QFN (6x6) 28 50 1600 ML QFN (4x4) 16 91 3300 Analog and Interface Product Selector Guide ANALOG PRODUCT PART NUMBERS Part Number Suffix Designations Ordering Information for all Microchip Analog Products beginning with "RE46C" prefix RE46C xxx yyyy zz Tape and Reel: TF: Tape and Reel F: No Tape and Reel Package Type (2 to 4 characters, see table below) Product Part Number (3 characters, see specific data sheet) Product Prefix Package Description # of Pins Tube Qty. Reel Qty. E8 PDIP 8 60 n/a S8 SOIC 8 100 3300 E14 PDIP 14 30 n/a S14 SOIC 14 57 2600 E16 PDIP 16 30 n/a S16 SOIC 16 50 2600 SW16 SOIC (300 mil) 16 47 1000 Analog and Interface Product Selector Guide 35