LANGUAGE PRODUCT SPECIFICATION JAPANESE ENGLISH SCOPE 0.5 mm FPC This specification covers the 0.5mm PITCH FPC CONNECTOR series PRODUCT NAME AND PART NUMBER Product Name Part Number Housing Assembly 54550-**22 54550-**22 Embossed Tape Package for 54550-**22 54550-**33 *: RATINGS Item Standard Rated Voltage (MAX.) 50 V Rated Current (MAX.) 0.5 A [AC ( rms) / DC ] *1 Ambient Temperature Range Storage condition Refer to the drawing. -40C Temperature Humidity Term of Storage ~ + 85C *2 *3 -10 +50 85R.H. 85%R.H.MAX. (No condensation) 6 For 6 months after shipping (unopened packing) *1 Non-operating connectors after reflow must follow the operating temperature range condition. *2 This includes the terminal temperature rise generated by conducting electricity. *3FPC() Applicable FPC (wires and cables) must also meet the specified temperature range. REV. SHEET A 1-18 REVISE ON PC ONLY A RELEASED J2013-1113 `12/09/11 N.KONDO REV. DESCRIPTION DESIGN CONTROL STATUS J DOCUMENT NUMBER PS-54550-014 TITLE: 0.5 mm FPC CONN ZIF R/A (UPPER CONTACT) THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION WRITTEN BY: CHECKED BY: APPROVED BY: N.KONDO K.TAKAHASHI K.MORIKAWA DATE: YR/MO/DAY 2012/09/11 FILE NAME SHEET PS54550014.DOC 1 OF 18 EN-037(2012-05) LANGUAGE PRODUCT SPECIFICATION JAPANESE ENGLISH PERFORMANCE 4 - 1. Electrical Performance Test Condition Item 4-1-1 Contact Resistance 4-1-2 Insulation Resistance 4-1-3 Dielectric Strength FPC20mV 10mA (JIS C5402 5.4) Mate applicable FPC, measured at the open circuit voltage 20mV MAXIMUM and short circuit 10mA MAXIMUM. (JIS C5402 5.4) FPC DC 500V (JIS C5402 5.2/MIL-STD-202 302) 40 milliohm MAX. Mate applicable FPC, measured by applying DC 500V between adjacent terminal or terminal and ground. (JIS C5402 5.2/MIL-STD-202, Method 302) FPC AC250V1 2mA (JIS C5402 5.1/MIL-STD-202 301) 50 Megohm MIN. Mate applicable FPC, applying AC 250Veffective value) for 1 minute between adjacent terminal or terminal and ground. Induced current is 2mA. (JIS C5402 5.1/MIL-STD-202, Method 301) REVISE ON PC ONLY A Standard SEE SHEET 1 OF 18 No Breakdown TITLE: 0.5 mm FPC CONN ZIF R/A (UPPER CONTACT) REV. DESCRIPTION DOCUMENT NUMBER PS-54550-014 THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FILE NAME SHEET PS54550014.DOC 2 OF 18 EN-037(2012-05) LANGUAGE PRODUCT SPECIFICATION JAPANESE ENGLISH . Mechanical Performance Test Condition Item 4-2-1 Actuator Insertion/ Withdrawal Force FPC FPC Retention Force 4-2-2 4-2-3 Terminal/Housing Retention Force 4-2-4 Fitting Nail/ Housing Retention Force Standard FPC 7 Refer to paragraph 7 Mate applicable FPC, insert and withdraw the actuator. FPCFPC Mate applicable FPC, close actuator, and pull the FPC. Pull out the each terminal assembled in the housing. Pull out the each fitting nail assembled in the housing. SEE SHEET 1 OF 18 8 Refer to paragraph 8 0.5N {0.1kgf} MINIMUM REVISE ON PC ONLY A 3.0 N {0.3 kgf} MINIMUM TITLE: 0.5 mm FPC CONN ZIF R/A (UPPER CONTACT) REV. DESCRIPTION DOCUMENT NUMBER PS-54550-014 THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FILE NAME SHEET PS54550014.DOC 3 OF 18 EN-037(2012-05) LANGUAGE PRODUCT SPECIFICATION 4 - 3 Environmental Performance and Others Item 4-3-1 4-3-2 4-3-3 Test Condition 110FPC FPC 10 Durability of Insert FPC, close and open actuator, withdraw Actuator FPC to 10 cycles, at the speed rate of less Operation than 10 cycles per minute in power-off state. FPC (UL 498) Temperature Mate applicable FPC, measure the Rise temperature rise of contact when the maximum AC rated current is passed. (UL 498) DC1mA 3105510Hz/ 1.5mm2(6) (JIS C 60068-2-6 /MIL-STD-202 201) Mate applicable FPC, add to each 2 hours (total:6 hours), with ratio sweep 10-55-10 Hz Vibration per minute and total amplitude 1.5 mm vibration at 3 directions mutually vertical including fitting axis in DC 1 mA electricity state. (JIS C60068-2-6/MIL-STD-202, Method 201) DC 1mA 6 490m/s2 {50G} 11millisecond3 (JIS C60068-2-27 / MIL-STD-202 213) 4-3-4 Mechanical Shock Mate applicable FPC, add to each 3 times with impact of 490m/s2 on action time 11 milliseconds at 6 directions mutually vertical including fitting axis in DC 1 mA electricity state. (JIS C60068-2-27 / MIL-STD-202Method 213) REVISE ON PC ONLY A JAPANESE ENGLISH SEE SHEET 1 OF 18 Standard Contact Resistance 60 milliohm MAXIMUM Temperature Rise 30 C MAXIMUM Appearance No Damage Contact Resistance 60 milliohm MAXIMUM Discontinuity 1.0 microsecond MAXIMUM Appearance No Damage Contact Resistance 60 milliohm MAXIMUM Discontinuity 1.0 microsecond MAXIMUM TITLE: 0.5 mm FPC CONN ZIF R/A (UPPER CONTACT) REV. DESCRIPTION DOCUMENT NUMBER PS-54550-014 THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FILE NAME SHEET PS54550014.DOC 4 OF 18 EN-037(2012-05) LANGUAGE PRODUCT SPECIFICATION Item 4-3-5 4-3-6 Test Condition Standard FPC85296 12 ( JIS C60068-2-2/MIL-STD-202 108 ) Mate applicable FPC, exposing for 96 hours in the atmosphere of 85+/-2 degree C. After the test, allowed to stand at room temperature for 1 to 2 hours before checking functionality. (JIS C60068-2-2/MIL-STD-202 Method 108) FPC-40396 12 (JIS C60068-2-1) Mate applicable FPC, exposing for 96 hours in the atmosphere of -40+/-3 degree C. After the test, allowed to stand at room temperature for 1 to 2 hours before checking functionality. (JIS C60068-2-1) Heat Resistance Cold Resistance FPC6029095% 961 2 (JIS C60068-2-78/MIL-STD-202 103) Mate applicable FPC, exposing for 96 hours in an atmosphere of 60+/-2 degree C, relative humidity 90 to 95%. After the test, allowed to stand at room temperature for 1 to 2 hours before checking functionality. (JIS C60068-2-78/MIL-STD-202 Method 103) Humidity 4-3-7 JAPANESE ENGLISH FPC-40330+85 23015 5 12 Appearance No Damage Contact Resistance 60 milliohm MAXIMUM Appearance No Damage Contact Resistance 60 milliohm MAXIMUM Appearance No Damage Contact Resistance Dielectric Strength Insulation Resistance 60 milliohm MAXIMUM 4-1-3 Must meet 4-1-3 Appearance No Damage Contact Resistance 60 milliohm MAXIMUM 20 Megohms MINIMUM (JIS C60068-2-14) 4-3-8 Temperature Cycling Mate applicable FPC, exposing to 85+/-2 degree C and -40+/-3 degree C temperature exterms for 30 minutes each including a 0-5 minutes transition time. The above-mentioned condition is repeated 5 cycles. After the test, allowed to stand at the room temperature for 1 to 2 hours before checking functionality. (JIS C60068-2-14) REVISE ON PC ONLY A SEE SHEET 1 OF 18 TITLE: 0.5 mm FPC CONN ZIF R/A (UPPER CONTACT) REV. DESCRIPTION DOCUMENT NUMBER PS-54550-014 THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FILE NAME SHEET PS54550014.DOC 5 OF 18 EN-037(2012-05) LANGUAGE PRODUCT SPECIFICATION Item 4-3-9 4-3-10 4-3-11 4-3-12 Test Condition FPC3525 1%48 (JIS C60068-2-11/MIL-STD-202 101) Salt Spray SO2 Gas H2S Gas NH3 Gas Mate applicable FPC, exposing to the atmosphere where salt mist is diffused in. Other condition is written below. NaCl solution : 5+/-1% by weight Temperature : 35+/-2 degree C Duration : 48 hours After the test, they should be washed well by water and dried before checking functionality. (JIS C60068-2-11/MIL-STD-202 Method 101) FPC40225 5ppm 75R.H.96 Mate applicable FPC, exposing to the atmosphere is written below. Gas Concentration : SO2=25+/-5ppm Temperature : 40+/-2 degree C Humidity : 75%R.H. Duration : 96hours FPC40231ppm 75R.H.96 Mate applicable FPC, exposing to the atmosphere is written below. Gas Concentration : H2S=3+/-1ppm Temperature : 40+/-2 degree C Humidity : 75%R.H. Duration : 96hours FPC28% 40 Mate applicable FPC, allow to stand for 40 minutes in a container filled with NH3 gas(from density 28% ammonia water). REVISE ON PC ONLY A SEE SHEET 1 OF 18 JAPANESE ENGLISH Standard Appearance No Damage Contact Resistance 60 milliohm MAXIMUM Appearance No Damage Contact Resistance 60 milliohm MAXIMUM Appearance No Damage Contact Resistance 60 milliohm MAXIMUM Appearance No Damage Contact Resistance 60 milliohm MAXIMUM TITLE: 0.5 mm FPC CONN ZIF R/A (UPPER CONTACT) REV. DESCRIPTION DOCUMENT NUMBER PS-54550-014 THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FILE NAME SHEET PS54550014.DOC 6 OF 18 EN-037(2012-05) LANGUAGE PRODUCT SPECIFICATION Item 4-3-13 4-3-14 JAPANESE ENGLISH Test Condition 0.3mm0.3mm 245530.5 Solderability Resistance to SolderingHeat Dip 0.3mm from the tip of the solder tails and 0.3mm from fitting nail into the molten solder which is held at 245 +/-5 degree C for 3+/-0.5 seconds. (Reflow by Infrared Reflow Machine) 5 The product is reflowed using the reflow profile as shown paragraph 5. (Reflow by Manual Soldering iron) 0.2mm 3501031 Standard Solder Wetting 90% At least 90% of immersed area must show no voids, pin holes Appearance No damage after twice reflow Using a soldering iron (350+/-10 degrees C for 3+/-1 seconds)heat up the area 0.2mm from the tip of the solder tails and fitting nails. However, do not apply excessive pressure to either the terminals or fitting nails. Reference Standard { } Reference Unit 5 Sn-3Ag-0.5Cu The evaluation samples of each specification test are reflowed according to the recommended Print Circuit Board layout and the recommended metal mask thickness specified in the sales drawing. The reflow conditions followed are specified in the reflow profile in paragraph 5. Lead free solder (Sn-3Ag-0.5Cu) was used as the soldering paste REVISE ON PC ONLY A SEE SHEET 1 OF 18 TITLE: 0.5 mm FPC CONN ZIF R/A (UPPER CONTACT) REV. DESCRIPTION DOCUMENT NUMBER PS-54550-014 THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FILE NAME SHEET PS54550014.DOC 7 OF 18 EN-037(2012-05) LANGUAGE PRODUCT SPECIFICATION 5. JAPANESE ENGLISH INFRARED REFLOW CONDITION 2455 Peak Temp. 2455 degrees C 230 230 degrees C MAXIMUM 200 200 degrees C 150 3060 150 degrees C 90120 30~60 seconds Pre-heat: 90~120 seconds TEMPERATURE CONDITION GRAPH (Temperature is measured at the soldering area on the surface of the print circuit board) N2 () NOTE: Please investigate the mounting condition (reflow soldering condition) on your own devices beforehand. The mounting conditions may change due to the soldering temperature, soldering paste, air reflow machine, N2 reflow machine, and the type of printed circuit board. The different mounting conditions may have an influence on the product's performance. 6 PRODUCT SHAPE, DIMENSIONS AND MATERIALS ELVRoHS Product fulfills ELV and RoHS. Refer to the drawing about any other information. REVISE ON PC ONLY A SEE SHEET 1 OF 18 TITLE: 0.5 mm FPC CONN ZIF R/A (UPPER CONTACT) REV. DESCRIPTION DOCUMENT NUMBER PS-54550-014 THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FILE NAME SHEET PS54550014.DOC 8 OF 18 EN-037(2012-05) LANGUAGE PRODUCT SPECIFICATION JAPANESE ENGLISH 7 ACTUATOR INSERTION AND WITHDRAWAL FORCE 0.3mmFPC FPC Table shown below is a data of actuator insertion and withdrawal force when using a thickness of 0.3mm FPC. But, there's a case which actuator insertion and withdrawal force doesn't fulfill the data value shown below, because FPC specification affects the result of actuator insertion and withdrawal force. No. of UNIT CIRCUIT 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 N {kgf} N {kgf} N {kgf} N {kgf} N {kgf} N {kgf} N {kgf} N {kgf} N {kgf} N {kgf} N {kgf} N {kgf} N {kgf} N {kgf} N {kgf} N {kgf} () Insertion Force (MAX.) 6 20 1st 6th 20th 28.4 26.4 26.4 {2.9} {2.7} {2.7} 29.4 27.4 27.4 {3.0} {2.8} {2.8} 30.3 28.4 28.4 {3.1} {2.9} {2.9} 31.3 29.4 29.4 {3.2} {3.0} {3.0} 32.3 30.3 30.3 {3.3} {3.1} {3.1} 33.3 31.3 31.3 {3.4} {3.2} {3.2} 34.3 32.3 32.3 {3.5} {3.3} {3.3} 35.2 33.3 33.3 {3.6} {3.4} {3.4} 36.2 34.3 34.3 {3.7} {3.5} {3.5} 37.2 35.3 35.3 {3.8} {3.6} {3.6} 38.2 36.2 36.2 {3.9} {3.7} {3.7} 39.2 37.2 37.2 {4.0} {3.8} {3.8} 40.1 38.2 38.2 {4.1} {3.9} {3.9} 41.1 39.2 39.2 {4.2} {4.0} {4.0} 42.1 40.1 40.1 {4.3} {4.1} {4.1} 43.1 41.1 41.1 {4.4} {4.2} {4.2} REVISE ON PC ONLY A SEE SHEET 1 OF 18 () Withdrawal Force (MAX.) 6 20 1st 6th 20th 37.2 33.3 33.3 {3.8} {3.4} {3.4} 38.2 34.3 34.3 {3.9} {3.5} {3.5} 39.2 35.2 35.2 {4.0} {3.6} {3.6} 40.1 36.2 36.2 {4.1} {3.7} {3.7} 41.1 37.2 37.2 {4.2} {3.8} {3.8} 42.1 38.2 38.2 {4.3} {3.9} {3.9} 43.1 39.2 39.2 {4.4} {4.0} {4.0} 44.1 40.1 40.1 {4.5} {4.1} {4.1} 45.0 41.1 41.1 {4.6} {4.2} {4.2} 46.0 42.1 42.1 {4.7} {4.3} {4.3} 47.0 43.1 43.1 {4.8} {4.4} {4.4} 48.0 44.1 44.1 {4.9} {4.5} {4.5} 49.0 45.0 45.0 {5.0} {4.6} {4.6} 49.9 46.0 46.0 {5.1} {4.7} {4.7} 50.9 47.0 47.0 {5.2} {4.8} {4.8} 51.9 48.0 48.0 {5.3} {4.9} {4.9} TITLE: 0.5 mm FPC CONN ZIF R/A (UPPER CONTACT) REV. DESCRIPTION DOCUMENT NUMBER PS-54550-014 THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FILE NAME SHEET PS54550014.DOC 9 OF 18 EN-037(2012-05) LANGUAGE PRODUCT SPECIFICATION No. of UNIT CIRCUIT 20 21 22 24 26 N {kgf} N {kgf} N {kgf} N {kgf} N {kgf} () Insertion Force (MAX.) 6 20 1st 6th 20th 44.1 42.1 42.1 {4.5} {4.3} {4.3} 45.0 43.1 43.1 {4.6} {4.4} {4.4} 46.0 44.1 44.1 {4.7} {4.5} {4.5} 48.0 46.0 46.0 {4.9} {4.7} {4.7} 50.0 48.0 48.0 {5.1} {4.9} {4.9} REVISE ON PC ONLY A SEE SHEET 1 OF 18 JAPANESE ENGLISH () Withdrawal Force (MAX.) 6 20 1st 6th 20th 52.9 49.0 49.0 {5.4} {5.0} {5.0} 53.9 49.9 49.9 {5.5} {5.1} {5.1} 54.8 50.9 50.9 {5.6} {5.2} {5.2} 56.8 52.9 52.9 {5.8} {5.4} {5.4} 58.8 54.8 54.8 {6.0} {5.6} {5.6} TITLE: 0.5 mm FPC CONN ZIF R/A (UPPER CONTACT) REV. DESCRIPTION DOCUMENT NUMBER PS-54550-014 THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FILE NAME SHEET PS54550014.DOC 10 OF 18 EN-037(2012-05) LANGUAGE PRODUCT SPECIFICATION JAPANESE ENGLISH 8FPC FPC RETENTION FORCE 0.3mmFPCFPCFPC FPCFPC Table shown below is a data of FPC retention force when using a thickness of 0.3mm FPC. But, there's a case which FPC retention force doesn't fulfill the data value shown below, because FPC specification affects the result of FPC retention force. 15 N {kgf} () Retention Force (MIN.) 10 1st 10th 4.0 3.5 {0.41} {0.36} 0.8 {0.08} 16 N {kgf} 4.3 {0.43} 3.8 {0.38} 1.5 {0.15} 1.2 {0.12} 17 N {kgf} 4.5 {0.45} 4.3 {0.43} N {kgf} 1.9 {0.19} 1.5 {0.15} 18 N {kgf} 4.7 {0.48} 4.3 {0.43} 8 N {kgf} 2.3 {0.23} 1.8 {0.18} 19 N {kgf} 4.9 {0.50} 4.5 {0.45} 9 N {kgf} 2.5 {0.25} 2.0 {0.20} 20 N {kgf} 5.2 {0.53} 4.7 {0.48} 10 N {kgf} 2.8 {0.28} 2.3 {0.23} 21 N {kgf} 5.4 {0.55} 4.9 {0.50} 11 N {kgf} 3.0 {0.30} 2.5 {0.25} 22 N {kgf} 5.7 {0.58} 5.2 {0.53} 12 N {kgf} 3.3 {0.33} 2.8 {0.28} 24 N {kgf} 6.2 {0.63} 5.7 {0.58} 13 N {kgf} 3.5 {0.35} 3.0 {0.30} 26 N {kgf} 6.7 {0.68} 6.3 {0.64} 14 N {kgf} 3.7 {0.38} 3.2 {0.33} No. of CIRCUIT UNIT () Retention Force (MIN.) 4 N {kgf} 1st 0.7 {0.07} 5 N {kgf} 1.1 {0.11} 6 N {kgf} 7 REVISE ON PC ONLY A SEE SHEET 1 OF 18 10 10th 0.4 {0.04} No. of CIRCUIT UNIT TITLE: 0.5 mm FPC CONN ZIF R/A (UPPER CONTACT) REV. DESCRIPTION DOCUMENT NUMBER PS-54550-014 THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FILE NAME SHEET PS54550014.DOC 11 OF 18 EN-037(2012-05) LANGUAGE PRODUCT SPECIFICATION JAPANESE ENGLISH 9. NOTES 9-1 9-1-1 Although this product may have a small black mark, a weld line or a scratch on the housing, these will not have any influence on the product's performance. 9-1-2 Although this product may have a small scratch on the the terminal and fitting nails, this will have no influence on the product's performance.. 9-1-3 Because we plate the terminal and fitting nails with Tin, there may be scratch marks on the surface. However, these scratches will have no influence on the product's performance. 9-1-4 There may be slight differences in the housing coloring, but there will be no influence on the product's performance. 9-1-5 Although the ultraviolet light may potentially change the actuator color, this change has no on the product's performance. 9-2 9-2-1 Max0.02mm The mounting specification for coplanarity does not include the influence of warpage of the printed circuit board. The warpage of the printed circuit board should be a maximum of 0.02mm if measuring from one connector edge to the other. 9-2-2 The product performance was tested using rigid printed circuit board. In case the product needs to be reflowed onto flexible circuit board, please conduct a reflow test on the flexible circuit board in advance. 9-2-3 Please add a stiffener on the flexible printed circuit (FPC) when you mount the connector onto FPC in order to prevent deformation of the FPC. REVISE ON PC ONLY A SEE SHEET 1 OF 18 TITLE: 0.5 mm FPC CONN ZIF R/A (UPPER CONTACT) REV. DESCRIPTION DOCUMENT NUMBER PS-54550-014 THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FILE NAME SHEET PS54550014.DOC 12 OF 18 EN-037(2012-05) LANGUAGE PRODUCT SPECIFICATION JAPANESE ENGLISH 9-2-4 Depending on the reflow conditions, there may be the possibility of a color change in the housing. However, this color change does not have any effect on the product's performance. 9-2-5 If you leave any soldering area on this product open, there may be the possibility of a missing terminal short circuiting between pins, terminal buckling or the potential for the connector to come off of the printed circuit board. Therefore, please solder all of the terminals and fitting nails on the printed circuit board. 9-2-6 If there is accidental contact with the connector while it is going through the reflow machine, there may be deformation or damage caused to the connector. Please check to prevent this. 9-3 9-3-1 Please do not conduct any "washing process" on the connector because it may damage the product's function. 9-3-2 FPC Please make sure to use the appropriate FPC which has Tin plating (Nickel under plating) on the contact area. 9-3-3 FPC Please check the compatibility between the connector and the FPC prior to moving to mass production. REVISE ON PC ONLY A SEE SHEET 1 OF 18 TITLE: 0.5 mm FPC CONN ZIF R/A (UPPER CONTACT) REV. DESCRIPTION DOCUMENT NUMBER PS-54550-014 THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FILE NAME SHEET PS54550014.DOC 13 OF 18 EN-037(2012-05) LANGUAGE PRODUCT SPECIFICATION JAPANESE ENGLISH 9-3-4 FPCFPC FPC FPC Please pay special attention not to have any pulling force/tension on the FPC when it is inserted into the connector. This can cause; the actuator to be unlocked, the actuator to come off, cut the traces on the FPC, and/or damage the FPC. Please be especially careful to avoid placing the FPC in a location where it will have a constant force applied on the FPC. If necessary, please fix the FPC directly on the chassis. Also, please avoid pulling the FPC vertically or twisting the FPC back and force horizontally while it is inserted in the connector. Figure 1 9-3-5 Please do not use the connector in a condition where the wire, the printed circuit board, or the contact area is experiencing a sympathetic vibration of wires and printed circuit board, and constant movement of devices. This may cause a defect in the contact due to the contact area being worn down. Therefore, please fix wires and printed circuit board on the chassis, and reduces sympathetic vibration. 9-3-6 This product is not designed for the mating and unmating of the connectors to be performed under the condition of an active electrical circuit. It may cause a spark and product defect if the connectors are mated and unmated in this way. REVISE ON PC ONLY A SEE SHEET 1 OF 18 TITLE: 0.5 mm FPC CONN ZIF R/A (UPPER CONTACT) REV. DESCRIPTION DOCUMENT NUMBER PS-54550-014 THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FILE NAME SHEET PS54550014.DOC 14 OF 18 EN-037(2012-05) LANGUAGE PRODUCT SPECIFICATION JAPANESE ENGLISH 9-3-7 FPC The terminals for this product are tin plated. We recommend that a Tin whiskering test is performed between your FPC and the connector beforehand to ensure that they are compatible. 9-3-8 Please keep enough clearance between connector and chassis of your application in order not to apply pressure on the connector. 9-3-9 Please do not stack the printed circuit board directly after mounted the connector on it. 9-4 9-4-1 Please do not touch the terminals and fitting nails before ot after reflowing the connector onto the printed circuit board. 9-4-2 FPCFPC FPCFPC When inserting the FPC into the connector, please ensure that the actuator is completely open during insertion. Please also ensure that the FPC is completely inserted until the end of the FPC touches the housing. Diagonal insertion of the FPC into the connector can cause a short circuit due to the misaligned pitch. Diagonal insertion can also deform the terminal and/or damage the FPC contact area because the FPC edge may contact the terminal. (Because this connector has a tentative cable-hold feature which holds the FPC in place prior to actuation, it may feel like there is a small insertion force when inserting the FPC. 9-4-3 When opening and closing the actuator, please do not use a sharp edged tool such as tweezers. This may cause to damage the connector or to the soldering area. REVISE ON PC ONLY A SEE SHEET 1 OF 18 TITLE: 0.5 mm FPC CONN ZIF R/A (UPPER CONTACT) REV. DESCRIPTION DOCUMENT NUMBER PS-54550-014 THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FILE NAME SHEET PS54550014.DOC 15 OF 18 EN-037(2012-05) LANGUAGE PRODUCT SPECIFICATION JAPANESE ENGLISH 9-4-4 When opening the actuator, please push the actuator by applying a force to the both sides of actuator. Please do not apply a force to only one side of actuator because it may cause to damage the connector. OK No Good Withdrawing on both sides of actuator Withdrawing Pushing only one side of actuator 2 Figure 2 9-4-5 When locking the actuator, please push the actuator by applying a force to only one side of actuator because it may cause to damage the connector. No Good OK Withdrawing on both sides of actuator Withdrawing Pushing only one side of actuator 3 Figure 3 REVISE ON PC ONLY A SEE SHEET 1 OF 18 TITLE: 0.5 mm FPC CONN ZIF R/A (UPPER CONTACT) REV. DESCRIPTION DOCUMENT NUMBER PS-54550-014 THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FILE NAME SHEET PS54550014.DOC 16 OF 18 EN-037(2012-05) LANGUAGE PRODUCT SPECIFICATION JAPANESE ENGLISH 9-4-6 FPC FPC When withdrawing the FPC, please make sure that the actuator is completely open. If the FPC is withdrawn without the actuator being fully open, please check to make sure that there is no debris on the contact area before inserting the FPC again. 9-4-7 After mated the connector, please do not allow the printed circuit boards to apply pressure on the connector in either the pitch direction or the span direction.It may cause damage to the connector and may crack the soldering. 9-5 9-5-1 When conducting manual repairs using a soldering iron, please follow the soldering conditions shown in the product specification. If the conditions in the product spec are not followed, it may cause the terminals to fall off, a change in the contact gap, a deformation of the housing, melting of the housing, and damage the connector. 9-5-2 When conducting manual repairs using a soldering iron, please do not use more solder and flux than needed. This may cause solder wicking and flux wicking issues, and it will eventually cause a contact defect and functional issues. REVISE ON PC ONLY A SEE SHEET 1 OF 18 TITLE: 0.5 mm FPC CONN ZIF R/A (UPPER CONTACT) REV. DESCRIPTION DOCUMENT NUMBER PS-54550-014 THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FILE NAME SHEET PS54550014.DOC 17 OF 18 EN-037(2012-05) LANGUAGE PRODUCT SPECIFICATION JAPANESE ENGLISH REV. REV. RECORD DATE ECN NO. WRITTEN BY: CHECKED BY: A RELEASED `12/09/11 J2013-1113 N.KONDO K.TAKAHASHI REVISE ON PC ONLY A SEE SHEET 1 OF 18 TITLE: 0.5 mm FPC CONN ZIF R/A (UPPER CONTACT) REV. DESCRIPTION DOCUMENT NUMBER PS-54550-014 THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FILE NAME SHEET PS54550014.DOC 18 OF 18 EN-037(2012-05)