SLOS070B − JULY 1979 − REVISED FEBRUARY 2004
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
DEquivalent Input Noise Voltage . . .
3.5 nV//Hz
DUnity-Gain Bandwidth . . . 10 MHz Typ
DCommon-Mode Rejection Ratio . . .
100 dB Typ
DHigh DC Voltage Gain . . . 100 V/mV Typ
DPeak-to-Peak Output Voltage Swing
32 V Typ With VCC+ = +18 V and RL = 600 W
DHigh Slew Rate . . . 13 V/ms Typ
DWide Supply-Voltage Range +3 V to +20 V
DLow Harmonic Distortion
DOffset Nulling Capability
DExternal Compensation Capability
description/ordering information
The NE5534 and NE5534A are high-performance operational amplifiers combining excellent dc and ac
characteristics. Some of the features include very low noise, high output-drive capability, high unity-gain and
maximum-output-swing bandwidths, low distortion, and high slew rate.
These operational amplifiers are compensated internally for a gain equal to or greater than three. Optimization
of the frequency response for various applications can be obtained by use of an external compensation
capacitor between COMP and COMP/BAL. The devices feature input-protection diodes, output short-circuit
protection, and offset-voltage nulling capability with use of the BALANCE and COMP/BAL pins (see the
application circuit diagram).
For the NE5534A, a maximum limit is specified for the equivalent input noise voltage.
ORDERING INFORMATION
TAVIOmax
AT 25°CPACKAGE†ORDERABLE
PART NUMBER TOP-SIDE
MARKING
PDIP (P)
Tube of 50 NE5534P NE5534P
PDIP (P) Tube of 50 NE5534AP NE5534AP
Tube of 75 NE5534D
NE5534
0°C to 70°C4 mV
SOIC (D)
Reel of 2500 NE5534DR NE5534
0C to 70 C
4 mV
SOIC (D) Tube of 75 NE5534AD
5534A
Reel of 2500 NE5534ADR 5534A
SOP (PS) Reel of 2000 NE5534PS N5534
†Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available
at www.ti.com/sc/package.
Copyright 2004, Texas Instruments Incorporated
!" #!$% &"'
&! #" #" (" " ") !"
&& *+' &! #", &" ""%+ %!&"
", %% #""'
1
2
3
4
8
7
6
5
BALANCE
IN−
IN+
VCC−
COMP/BAL
VCC+
OUT
COMP
NE5534 ...D, P, OR PS PACKAGE
NE5534A ...D OR P PACKAGE
(TOP VIEW)
SLOS070B − JULY 1979 − REVISED FEBRUARY 2004
2POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
schematic
VCC−
OUT
15 Ω
15 Ω
12 kΩ12 kΩ
7 pF
12 pF
40 pF
100 pF
IN+
IN−
BALANCE COMPCOMP/BAL
857
4
6
2
3
1
All component values shown are nominal.
VCC+
symbol
IN−
COMP/BAL
COMP
OUT
BALANCE
−
+
IN+
application circuit
−
+
22 kΩ
100 kΩ
7
2
3
VCC−
4
6
5
8
VCC+
1
CC
5534
Frequency Compensation and Offset-Voltage Nulling Circuit
SLOS070B − JULY 1979 − REVISED FEBRUARY 2004
3
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage: VCC+ (see Note 1) 22 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VCC− (see Note 1) −22 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input voltage either input (see Notes 1 and 2) VCC+
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input current (see Note 3) ±10 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Duration of output short circuit (see Note 4) Unlimited. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Package thermal impedance, θJA (see Notes 5 and 6): D package 97°C/W. . . . . . . . . . . . . . . . . . . . . . . . . . . .
P package 85°C/W. . . . . . . . . . . . . . . . . . . . . . . . . . . .
PS package 95°C/W. . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating virtual junction temperature, TJ 150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage temperature range, Tstg −65°C to 150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
†Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltage values, except differential voltages, are with respect to the midpoint between VCC+ and VCC−.
2. The magnitude of the input voltage must never exceed the magnitude of the supply voltage.
3. Excessive current will flow if a dif ferential input voltage in excess of approximately 0.6 V is applied between the inputs, unless some
limiting resistance is used.
4. The output may be shorted to ground or to either power supply. Temperature and/or supply voltages must be limited to ensure the
maximum dissipation rating is not exceeded.
5. Maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation at any allowable
ambient temperature is PD = (TJ(max) − TA)/θJA. Operating at the absolute maximum TJ of 150°C can affect reliability.
6. The package thermal impedance is calculated in accordance with JESD 51-7.
recommended operating conditions
MIN MAX UNIT
VCC+ Supply voltage 5 15 V
VCC− Supply voltage −5 −15 V
SLOS070B − JULY 1979 − REVISED FEBRUARY 2004
4POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
electrical characteristics, VCC± = ±15 V, TA = 25°C (unless otherwise noted)
PARAMETER TEST CONDITIONS†MIN TYP MAX UNIT
VIO
Input offset voltage
VO = 0,
TA = 25°C 0.5 4
mV
VIO Input offset voltage
VO = 0,
RS = 50 ΩTA = Full range 5mV
IIO
Input offset current
VO = 0
TA = 25°C 20 300
nA
IIO Input offset current VO = 0 TA = Full range 400 nA
IIB
Input bias current
VO = 0
TA = 25°C 500 1500
nA
IIB Input bias current VO = 0 TA = Full range 2000 nA
VICR Common-mode input voltage range ±12 ±13 V
VO(PP)
Maximum peak-to-peak output voltage swing
RL ≥ 600 Ω
VCC± = ±15 V 24 26
V
VO(PP
)
Maximum peak-to-peak output voltage swing RL ≥ 600 ΩVCC± = ±18 V 30 32 V
AVD
Large-signal differential voltage amplification
VO =
±
10 V,
TA = 25°C 25 100
V/mV
AVD Large-signal differential voltage amplification
VO = ±10 V,
RL ≥ 600 ΩTA = Full range 15 V/mV
Avd
Small-signal differential voltage amplification
f = 10 kHz
CC = 0 6
V/mV
Avd Small-signal differential voltage amplification f = 10 kHz CC = 22 pF 2.2 V/mV
VO = ±10 V
CC = 0 200
BOM
Maximum-output-swing bandwidth
VO = ±10 V CC = 22 pF 95
kHz
B
OM
Maximum-output-swing bandwidth
VCC± = ±18 V,
RL ≥ 600 Ω, VO = ±14 V,
CC = 22 pF 70
kHz
B1Unity-gain bandwidth CC = 22 pF, CL = 100 pF 10 MHz
riInput resistance 30 100 kΩ
zoOutput impedance AVD = 30 dB,
CC = 22 pF, RL ≥ 600 Ω,
f = 10 kHz 0.3 Ω
CMRR Common-mode rejection ratio VO = 0,
RS = 50 ΩVIC = VICRmin,70 100 dB
kSVR Supply-voltage rejection ratio (∆VCC/∆VIO) VCC+ = ±9 V to ±15 V,
VO = 0 RS = 50 Ω,80 100 dB
IOS Output short-circuit current 38 mA
ICC Supply current VO = 0, No load TA = 25°C 4 8 mA
†All characteristics are measured under open-loop conditions with zero common-mode input voltage, unless otherwise specified. Full range is
TA = 0°C to 70°C.
operating characteristics, VCC ± = ±15 V, TA = 25°C
PARAMETER
TEST CONDITIONS
NE5534 NE5534A
UNIT
PARAMETER
TEST CONDITIONS
TYP MIN TYP MAX
UNIT
SR
Slew rate
CC = 0 13 13
V/ s
SR Slew rate CC = 22 pF 6 6 V/µs
Rise time VI = 50 mV,
RL = 600 Ω,
AVD = 1,
CC = 22 pF
20 20 ns
tr
Overshoot factor
I
R
L
= 600
Ω
,
CL = 100 pF
C
C
= 22 pF
20 20 %
trRise time VI = 50 mV,
RL = 600 Ω,
AVD = 1,
CC = 47 pF
50 50 ns
Overshoot factor
I
R
L
= 600
Ω
,
CL = 500 pF
C
C
= 47 pF
35 35 %
Vn
Equivalent input noise voltage
f = 30 Hz 7 5.5 7
nV/√Hz
VnEquivalent input noise voltage f = 1 kHz 4 3.5 4.5 nV/√Hz
In
Equivalent input noise current
f = 30 Hz 2.5 1.5
pA/√Hz
InEquivalent input noise current f = 1 kHz 0.6 0.4 pA/√Hz
FAverage noise figure RS = 5 kΩ, f = 10 Hz to 20 kHz 0.9 dB
SLOS070B − JULY 1979 − REVISED FEBRUARY 2004
5
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS†
Figure 1
1
0.8
0.6
0.4−75 −50 −25 0 25 50
Normalized Input Bias Current and Input Offset Current
1.2
1.4
NORMALIZED INPUT BIAS CURRENT
AND INPUT OFFSET CURRENT
vs
FREE-AIR TEMPERATURE
1.6
75 100 125
TA − Free-Air Temperature − °C
VCC± = ±15 V
Offset
Bias
Figure 2
100 1 k 10 k 100 k 1 M
V
f − Frequency − Hz
MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE
vs
FREQUENCY
OPP − Maximum Peak-to-Peak Output Voltage − V
30
25
20
15
10
5
0
ÁÁÁ
ÁÁÁ
ÁÁÁ
VO(PP)
VCC± = ±15 V
TA = 25°C
CC = 22 pF
CC = 47 pF
CC = 0
Figure 3
A
LARGE-SIGNAL
DIFFERENTIAL VOLTAGE AMPLIFICATION
vs
FREQUENCY
f − Frequency − Hz
VCC± = ±15 V
TA = 25°C
CC = 0 pF
CC = 22 pF
106
105
104
103
102
10
1
VD − Differential Voltage Amplification − V/mV
10 100 1 k 10 k 100 k 1 M 10 M 100 M
Figure 4
0.8
0.6
0.5
0.4 0510
Normalized Slew Rate and Unity-Gain Bandwidth
1
1.1
NORMALIZED SLEW RATE AND
UNITY-GAIN BANDWIDTH
vs
SUPPLY VOLTAGE
1.2
15 20
0.9
0.7
| VCC± | − Supply Voltage − V
TA = 25°C
Unity-Gain
Bandwidth
Slew Rate
†Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
SLOS070B − JULY 1979 − REVISED FEBRUARY 2004
6POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS†
Figure 5
1
0.9
0.8
−75 −50 −25 0 25 50
Normalized Slew Rate and Unity-Gain Bandwidth
1.1
NORMALIZED SLEW RATE AND
UNITY-GAIN BANDWIDTH
vs
FREE-AIR TEMPERATURE
1.2
75 100 125
VCC± = ±15 V
TA − Free-Air Temperature − °C
Unity-Gain
Bandwidth
Slew Rate
Figure 6
100 400 1 k
THD − Total Harmonic Distortion − %
f − Frequency − Hz
TOTAL HARMONIC DISTORTION
vs
FREQUENCY
4 k 10 k 40 k 100 k
0.01
0.007
0.004
0.002
0.001
VCC± = ±15 V
AVD = 1
VI(rms) = 2 V
TA = 25°C
Figure 7
10 100
− Equivalent Input Noise Voltage −
f − Frequency − Hz
EQUIVALENT INPUT NOISE VOLTAGE
vs
FREQUENCY
1 k 10 k 100 k
VnnV/ Hz
10
7
4
2
1
VCC± = ±15 V
TA = 25°C
SE5534A, NE5534A
SE5534, NE5534
Figure 8
10 100 f − Frequency − Hz
1 k 10 k 100 k
EQUIVALENT INPUT NOISE CURRENT
vs
FREQUENCY
− Equivalent Input Noise Current −
InpA/ Hz
10
7
4
2
1
0.7
0.4
0.2
0.1
VCC± = ±15 V
TA = 25°C
SE5534, NE5534
SE5534A, NE5534A
†Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
SLOS070B − JULY 1979 − REVISED FEBRUARY 2004
7
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 9
0.7
0.4
0.2
0.1
100 1 k 10 k 100 k 1 M
Total Equivalent Input Noise Voltage −
1
TOTAL EQUIVALENT INPUT NOISE VOLTAGE
vs
SOURCE RESISTANCE
7
4
2
10
70
40
20
100
µV
RS − Source Resistance − Ω
VCC± = ±15 V
TA = 25°C
f = 10 Hz to 20 kHz
f = 200 Hz to 4 kHz
MECHANICAL DATA
MCER001A – JANUARY 1995 – REVISED JANUAR Y 1997
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
JG (R-GDIP-T8) CERAMIC DUAL-IN-LINE
0.310 (7,87)
0.290 (7,37)
0.014 (0,36)
0.008 (0,20)
Seating Plane
4040107/C 08/96
5
4
0.065 (1,65)
0.045 (1,14)
8
1
0.020 (0,51) MIN
0.400 (10,16)
0.355 (9,00)
0.015 (0,38)
0.023 (0,58)
0.063 (1,60)
0.015 (0,38)
0.200 (5,08) MAX
0.130 (3,30) MIN
0.245 (6,22)
0.280 (7,11)
0.100 (2,54)
0°–15°
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. This package can be hermetically sealed with a ceramic lid using glass frit.
D. Index point is provided on cap for terminal identification.
E. Falls within MIL STD 1835 GDIP1-T8
MECHANICAL DATA
MPDI001A – JANUARY 1995 – REVISED JUNE 1999
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
P (R-PDIP-T8) PLASTIC DUAL-IN-LINE
8
4
0.015 (0,38)
Gage Plane
0.325 (8,26)
0.300 (7,62)
0.010 (0,25) NOM
MAX
0.430 (10,92)
4040082/D 05/98
0.200 (5,08) MAX
0.125 (3,18) MIN
5
0.355 (9,02)
0.020 (0,51) MIN
0.070 (1,78) MAX
0.240 (6,10)
0.260 (6,60)
0.400 (10,60)
1
0.015 (0,38)
0.021 (0,53)
Seating Plane
M
0.010 (0,25)
0.100 (2,54)
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-001
For the latest package information, go to http://www.ti.com/sc/docs/package/pkg_info.htm
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’ s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of T I products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products Applications
Amplifiers amplifier.ti.com Audio www.ti.com/audio
Data Converters dataconverter.ti.com Automotive www.ti.com/automotive
DSP dsp.ti.com Broadband www.ti.com/broadband
Interface interface.ti.com Digital Control www.ti.com/digitalcontrol
Logic logic.ti.com Military www.ti.com/military
Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork
Microcontrollers microcontroller.ti.com Security www.ti.com/security
Telephony www.ti.com/telephony
Video & Imaging www.ti.com/video
Wireless www.ti.com/wireless
Mailing Address: Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright 2004, Texas Instruments Incorporated
