19-4353; Rev 1; 5/12 KIT ATION EVALU E L B A IL AVA Boost Regulator with Integrated Charge Pumps, Switch Control, and High-Current Op Amp Features The MAX17075 includes a high-voltage boost regulator, one high-current operational amplifier, two regulated charge pumps, and one MLG block for gate-driver supply modulation. The step-up DC-DC converter is a 1.2MHz currentmode boost regulator with a built-in power MOSFET. It provides fast load-transient response to pulsed loads while producing efficiencies over 85%. The built-in 160m (typ) power MOSFET allows output voltages as high as 18V boosted from inputs ranging from 2.5V to 5.5V. A built-in 7-bit digital soft-start function controls startup inrush currents. The gate-on and gate-off charge pumps provide regulated TFT gate-on and gate-off supplies. Both output voltages can be adjusted with external resistive voltage-dividers. o 2.5V to 5.5V Input Operating Range o Current Mode Step-Up Regulator Fast-Transient Response Built-In 20V, 3A, 0.16 n-Channel Power MOSFET Cycle-by-Cycle Current Limit 87% Efficiency (5V Input to 13V Output) 1.2MHz Switching Frequency 1% Output Voltage Regulation Accuracy o High-Current 18V VCOM Buffer 500mA Output Short-Circuit Current 45V/s Slew Rate 20MHz -3dB Bandwidth Rail-to-Rail Output The operational amplifier, typically used to drive the LCD backplane (VCOM), features high-output short-circuit current (500mA), fast slew-rate (45V/s), wide bandwidth (20MHz), and rail-to-rail outputs. The MAX17075 is available in a 24-pin thin QFN package with 0.5mm lead spacing. The package is a square (4mm x 4mm) with a maximum thickness of 0.8mm for ultra-thin LCD design. It operates over the -40C to +85C temperature range. Applications o Regulated Charge Pump for TFT Gate-On Supply o Regulated Charge Pump for TFT Gate-Off Supply o Logic-Controlled High-Voltage Switches with Adjustable Delay o Soft-Start and Timed Delay Fault Latch for All Outputs o Overload and Thermal Protection Simplified Operating Circuit VMAIN VIN 2.5V TO 5.5V R1 10 Notebook Computer Displays VCC C5 1F LCD Monitor Panels LCD TVs LX PGND FROM SYSTEM 3.3V FB COMP TO VCOM OUT VIN VAVDD Ordering Information PART TEMP RANGE MAX17075 BGND PIN-PACKAGE MAX17075ETG+ -40C to +85C 24 TQFN-EP* *EP = Exposed paddle. +Denotes a lead(Pb)-free/RoHS-compliant package. NEG RST RSTIN POS DRN REF COM AGND VGON SRC FBN DRVP VGOFF DRVN BGND SUP CTL EP Pin Configuration appears at end of data sheet. FBP DEL FROM TCON ________________________________________________________________ Maxim Integrated Products For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim's website at www.maxim-ic.com. 1 MAX17075 General Description MAX17075 Boost Regulator with Integrated Charge Pumps, Switch Control, and High-Current Op Amp ABSOLUTE MAXIMUM RATINGS VCC, CTL, RSTIN, RST to AGND ..........................-0.3V to +7.5V DEL, REF, COMP, FB, FBN, FBP to AGND .......................................-0.3V to (VVCC + 0.3V) PGND, BGND to AGND.........................................-0.3V to +0.3V LX to PGND ............................................................-0.3V to +20V SUP to PGND .........................................................-0.3V to +20V DRVN, DRVP to PGND..............................-0.3V to (VSUP + 0.3V) SRC, COM, DRN to AGND .....................................-0.3V to +40V DRN to COM............................................................-30V to +30V SRC to SUP ............................................................................23V REF Short Circuit to AGND.........................................Continuous POS, NEG, OUT to AGND...........................-0.3V to (VSUP + 0.3) DRVN, DRVP RMS Current ...............................................200mA LX, PGND RMS Current Rating.............................................2.4A Continuous Power Dissipation (TA = +70C) 24-Pin TQFN (derate 27.8mW/C above +70C).......2222mW Operating Temperature Range ...........................-40C to +85C Junction Temperature ......................................................+150C Storage Temperature Range .............................-65C to +160C Lead Temperature (soldering, 10s) .................................+300C Soldering Temperature (reflow) .......................................+260C Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS (VVCC = +5V, Circuit of Figure 1, VAVDD = VSUP = +13V, TA = 0C to +85C, unless otherwise noted. Typical values are at TA = +25C.) PARAMETER CONDITIONS TYP MAX 5.5 V 2.25 2.45 V 100 200 A VFB = 1.3V, not switching 1 1.5 VFB = 1.0V, switching 4 5 1.250 1.262 V 6 mV VCC Input Supply Range 2.5 VCC Undervoltage-Lockout (UVLO) Threshold VCC rising, hysteresis (typ) = 50mV VCC Shutdown Current VCC = 2V VCC Quiescent Current MIN 2.05 UNITS mA REFERENCE REF Output Voltage No external load REF Load Regulation 0n < ILOAD < 50A REF Sink Current In regulation REF Undervoltage-Lockout Threshold Rising edge, hysteresis (typ) = 200mV 1.238 10 A 1 1.17 V 1000 1200 1400 kHz OSCILLATOR AND TIMING Frequency Oscillator Maximum Duty Cycle 87 90 93 % Duration to Trigger Fault Condition FB or FBP or FBN below threshold 47 55 65 ms DEL Capacitor Charge Current During startup, VDEL = 1.0V 4 5 6 A 1.19 1.25 1.31 DEL Turn-On Threshold DEL Discharge Switch On-Resistance V 20 STEP-UP REGULATOR Output Voltage Range 18 V FB Regulation Voltage FB = COMP, CCOMP = 1nF 1.238 VVCC 1.250 1.262 V FB Fault Trip Level Falling edge 0.96 1 1.04 V FB Load Regulation 0 < ILOAD < full, transient only FB Line Regulation VCC = 2.5V to 5.5V FB Input Bias Current -1 % -0.2 0 +0.2 %/V VFB = 1.25V 50 125 200 nA FB Transconductance I = 2.5A at COMP, FB = COMP 75 160 280 FB Voltage Gain FB to COMP 2 2600 _______________________________________________________________________________________ S V/V Boost Regulator with Integrated Charge Pumps, Switch Control, and High-Current Op Amp (VVCC = +5V, Circuit of Figure 1, VAVDD = VSUP = +13V, TA = 0C to +85C, unless otherwise noted. Typical values are at TA = +25C.) PARAMETER CONDITIONS LX Current Limit VFB = 1.1V, duty cycle = 75% LX On-Resistance ILX = 200mA LX Leakage Current VLX = 19V, TA = +25C Current-Sense Transresistance Soft-Start Period MIN TYP MAX UNITS 2.5 3.0 3.5 A 0.16 0.25 10 20 A 0.2 0.3 V/A 0.1 7-bit current ramp 14 ms POSITIVE CHARGE-PUMP REGULATOR VSUP Input Supply Range VSUP Overvoltage Threshold 6 VSUP = rising, hysteresis = 200mV 19 V 21 V 0.5 x f OSC Operating Frequency FBP Regulation Voltage -1.5% FBP Line Regulation Error VSUP = 12V to 18V, VGON = 30V FBP Input Bias Current VFBP = 1.5V, TA = +25C Not in dropout DRVP Current Limit 20 18 1.250 -50 Hz +1.5% V 0.2 %/V +50 nA 400 mA DRVP PCH On-Resistance 4 6 DRVP NCH On-Resistance 1.5 3 1 1.04 V 3 5 ms 18 V FBP Fault Trip Level Falling edge Positive Charge-Pump Soft-Start Period 7-bit voltage ramp with filtering to prevent high peak currents 0.96 NEGATIVE CHARGE-PUMP REGULATOR VSUP Input Supply Range 6 0.5 x f OSC Operating Frequency FBN Regulation Voltage (VREF - VFBN) VREF - VFBN = 1V FBN Input Bias Current VFBN = 0V, TA = +25C FBN Line Regulation Error VSUP = 9V to 18V, VGOFF = -7V -1.5% 1 -50 Hz +1.5% V +50 nA 0.2 %/V DRVN PCH On-Resistance 4 6 DRVN NCH On-Resistance 1.5 3 DRVN Current Limit Not in dropout 400 mA FBN Fault Trip level Rising edge 450 mV Negative Charge-Pump Soft-Start Period 7-bit voltage ramp with filtering to prevent high peak currents 3 5 ms 0.6 V +1 A POSITIVE GATE DRIVER TIMING AND CONTROL SWITCHES CTL Input Low Voltage CTL Input High Voltage 2 CTL Input Current VCTL = 0V or VVCC, TA = +25C CTL-to-COM Rising Propagation Delay CLOAD = 100pF V -1 250 SRC Input Voltage Range SRC-to-COM Switch On-Resistance VDEL = 1.5V, CTL = VCC 5 ns 36 V 10 _______________________________________________________________________________________ 3 MAX17075 ELECTRICAL CHARACTERISTICS (continued) MAX17075 Boost Regulator with Integrated Charge Pumps, Switch Control, and High-Current Op Amp ELECTRICAL CHARACTERISTICS (continued) (VVCC = +5V, Circuit of Figure 1, VAVDD = VSUP = +13V, TA = 0C to +85C, unless otherwise noted. Typical values are at TA = +25C.) TYP MAX DRN-to-COM Switch On-Resistance PARAMETER VDEL = 1.5V, CTL = AGND 30 60 COM-to-GND Pulldown VDEL = 0V 1.5 2.5 k SRC Input Current CONDITIONS MIN UNITS VDEL = 1.5V, CTL = VCC 300 600 VDEL = 1.5V, CTL = AGND 200 360 18 V 4 4.2 V 4 6.5 mA 12 mV +1 A A OPERATIONAL AMPLIFIERS SUP Supply Range 6 VSUP Undervoltage Threshold 3.8 SUP Supply Current Buffer configuration, VPOS = VSUP/2, no load Input Offset Voltage VNEG, V POS = V SUP/2, TA = +25C Input Bias Current VNEG, V POS = V SUP/2, TA = +25C Input Common-Mode Voltage Range -1 0 Input Common-Mode Rejection Ratio VSUP 80 Output-Voltage-Swing High I OUT = 50mA Output-Voltage-Swing Low I OUT = -50mA Large-Signal Voltage Gain VOUT = 1V to (VSUP - 1)V V dB VSUP 350 mV 350 80 mV dB Slew Rate 45 V/s -3dB Bandwidth 20 MHz Short-Circuit Current Sourcing 500 Sinking 500 mA XAO CONTROL RSTIN Threshold RSTIN Input Current Falling edge at VCC = 5V 1.225 1.250 1.275 Falling edge at VCC = 1.8V 1.213 1.250 1.287 TA = +25C -1 RSTIN Hysteresis RST Output Voltage I SINK = 1mA RST Blanking Time Counting from VVCC crossing 2.25V XAO UVLO VVCC rising with hysteresis of 50mV 4 +1 50 160 V A mV 0.4 V 220 280 ms 1.5 1.7 V _______________________________________________________________________________________ Boost Regulator with Integrated Charge Pumps, Switch Control, and High-Current Op Amp (VCC = +5V, Circuit of Figure 1, VAVDD = VSUP = +13V, TA = -40C to +85C, unless otherwise noted.) (Note 1) PARAMETER CONDITIONS VCC Input Supply Range VCC Undervoltage-Lockout Threshold VCC rising, hysteresis (typ) = 50mV MIN MAX UNITS 2.5 TYP 5.5 V 2.05 2.45 V 200 A VCC Shutdown Current VCC Quiescent Current VFB = 1.3V, not switching 1.5 VFB = 1.0V, switching 5 mA REFERENCE REF Output Voltage No external load REF Load Regulation 0 < ILOAD < 50A REF Sink Current In regulation REF Undervoltage-Lockout Threshold Rising edge, hysteresis (typ) = 200mV 1.230 1.267 V 6 mV 10 A 1.15 V 1000 1400 kHz OSCILLATOR AND TIMING Frequency Oscillator Maximum Duty Cycle 86 94 % Duration to Trigger Fault Condition FB or FBP or FBN below threshold 47 65 ms DEL Capacitor Charge Current During startup, VDEL = 1.0V 4 6 A 1.19 1.31 V VIN 18 V V DEL Turn-On Threshold STEP-UP REGULATOR Output Voltage Range FB Regulation Voltage FB = COMP, CCOMP = 1nF 1.230 1.267 FB Fault Trip Level Falling edge 0.96 1.04 V FB Line Regulation VCC = 2.5V to 5.5V -0.25 +0.25 %/V FB Input Bias Current VFB = 1.25V 50 200 nA FB Transconductance I = 2.5A at COMP, FB = COMP 75 280 S LX Current Limit VFB = 1.1V, duty cycle = 75% 2.5 3.5 A LX On-Resistance ILX = 200mA Current-Sense Transresistance 0.10 0.25 0.30 V/A POSITIVE CHARGE-PUMP REGULATOR VSUP Input Supply Range VSUP Overvoltage Threshold FBP Regulation Voltage FBP Line Regulation Error FBP Input Bias Current DRVP PCH On-Resistance DRVP NCH On-Resistance FBP Fault Trip Level Positive Charge-Pump Soft-Start Period VSUP = rising, hysteresis = 200mV 6 18 V 19 21 V +2% 0.2 +50 6 3 1.04 V %/V nA V 5 ms -2% VSUP = 8V to 18V, VGON = 30V VFBP = 1.5V, TA = +25C -50 Falling edge 0.96 7-bit voltage ramp with filtering to prevent high peak currents 1.25 _______________________________________________________________________________________ 5 MAX17075 ELECTRICAL CHARACTERISTICS MAX17075 Boost Regulator with Integrated Charge Pumps, Switch Control, and High-Current Op Amp ELECTRICAL CHARACTERISTICS (continued) (VCC = +5V, Circuit of Figure 1, VAVDD = VSUP = +13V, TA = -40C to +85C, unless otherwise noted.) (Note 1) PARAMETER NEGATIVE CHARGE-PUMP REGULATOR VSUP Input Supply Range FBN Regulation Voltage (VREF - VFBN) FBN Input Bias Current FBN Line Regulation Error DRVN PCH On-Resistance DRVN NCH On-Resistance Negative Charge-Pump Soft-Start Period CONDITIONS VREF - VFBN = 1V VFBN = 0V, TA = +25C VSUP = 9V to 18V, VGOFF = -7V MIN TYP 6 -2% -50 1 7-bit voltage ramp with filtering to prevent high peak currents POSITIVE GATE-DRIVER TIMING AND CONTROL SWITCHES CTL Input Low Voltage CTL Input High Voltage CTL Input Current VCTL = 0V or VVCC, TA = +25C SRC Input Voltage Range SRC-to-COM Switch On-Resistance VDEL = 1.5V, CTL = VCC DRN-to-COM Switch On-Resistance VDEL = 1.5V, CTL = AGND COM-to-GND Pulldown VDEL = 0V VDEL = 1.5V, CTL = VCC SRC Input Current VDEL = 1.5V, CTL = AGND OPERATIONAL AMPLIFIERS SUP Supply Range VSUP Undervoltage Threshold SUP Supply Current Buffer configuration, VPOS = VSUP/2, no load Input Offset Voltage VNEG, V POS = V SUP/2, TA = +25C Input Bias Current VNEG, V POS = V SUP/2, TA = +25C Input Common-Mode Voltage Range 2 -1 1.5 6 3.8 -1 0 I OUT = 50mA Output-Voltage-Swing Low I OUT = -50mA Short-Circuit Current Sourcing Sinking 500 500 Falling edge TA = +25C I SINK = 1mA Counting from VVCC crossing 2.25V VCC rising with typical hysteresis of 50mV 1.22 -1 18 +2% +50 0.2 6 3 V V nA %/V 5 ms 0.6 +1 36 10 60 2.5 600 360 V V A V k A A 18 4.2 6.5 8 +1 VSUP V V mA mV A V mV 350 160 Note 1: -40C specifcations are guaranteed by design, not production tested. 6 UNITS VSUP 350 Output-Voltage-Swing High XAO CONTROL RSTIN Threshold RSTIN Input Current RST Output Voltage RST Blanking Time XAO UVLO 4 MAX _______________________________________________________________________________________ mV mA 1.28 +1 0.4 280 1.7 V A V ms V Boost Regulator with Integrated Charge Pumps, Switch Control, and High-Current Op Amp 0.4 VIN = 3.3V 50 VIN = 2.5V 40 30 0.2 0.15 OUTPUT ERROR (%) 60 OUTPUT ERROR (%) 70 0.20 MAX17075 toc02 VIN = 5V 80 0 -0.2 -0.4 0.10 300mA LOAD NO LOAD 0.05 0 200mA LOAD -0.05 -0.6 -0.10 -0.8 -0.15 20 100mA LOAD 10 0 -1.0 10 100 -0.20 0 100 200 300 400 500 600 700 800 900 1000 1000 LOAD CURRENT (mA) 2.5 LOAD CURRENT (mA) 3.0 3.5 4.0 4.5 5.0 INPUT VOLTAGE (V) STEP-UP REGULATOR STARTUP WITH HEAVY LOAD (600mA) STEP-UP REGULATOR SWITCHING FREQUENCY vs. INPUT VOLTAGE MAX17075 toc05 1.24 MAX17075 toc04 1 150mA LOAD 1.23 SWITCHING FREQUENCY (MHz) EFFICIENCY (%) 0.6 MAX17075 toc01 100 90 STEP-UP REGULATOR LINE REGULATION UNDER DIFFERENT LOADS STEP-UP REGULATOR OUTPUT VOLTAGE vs. LOAD CURRENT MAX17075 toc03 STEP-UP REGULATOR EFFICIENCY vs. LOAD CURRENT 1.22 VIN 5V/div VAVDD 5V/div 0V 1.21 0V 1.20 IL 1A/div 1.19 1.18 0A 1.17 0V LX 10V/div 1.16 2.5 3.0 3.5 4.0 4.5 5.0 2ms/div INPUT VOLTAGE (V) STEP-UP REGULATOR LOAD-TRANSIENT RESPONSE (100mA TO 800mA) STEP-UP REGULATOR PULSED LOAD-TRANSIENT RESPONSE (80mA TO 2.08mA) MAX17075 toc06 MAX17075 toc07 0V VAVDD (AC-COUPLED) 500mV/div 0A IL 2A/div VAVDD (AC-COUPLED) 500mV/div 0V IL 2A/div 0A LOAD CURRENT 500mA/div 0A RCOMP = 82k CCOMP1 = 220pF CCOMP2 = 18pF 40s/div LOAD CURRENT 1A/div 0A RCOMP = 82k CCOMP1 = 220pF CCOMP2 = 18pF 10s/div _______________________________________________________________________________________ 7 MAX17075 Typical Operating Characteristics (TA = +25C, unless otherwise noted.) Typical Operating Characteristics (continued) (TA = +25C, unless otherwise noted.) IN SUPPLY QUIESCENT CURRENT vs. IN SUPPLY VOLTAGE POWER-UP SEQUENCE OF ALL SUPPLY OUTPUTS MAX17075 toc09 SUPPLY CURRENT (mA) 3.5 MAX17075 toc08 4.0 200mA LOAD 0V 0V 2.5 0V 2.0 VCOM SRC 0V NO SWITCHING 0V 1.5 DEL GOFF GON 1.0 0V 0 3.0 3.5 4.0 4.5 5.0 POSITIVE CHARGE-PUMP REGULATOR LINE REGULATION 0 -0.10 -0.15 -0.20 MAX17075 toc12 0.4 VSRC 0 OUTPUT ERROR (%) -0.05 SRC : 20V/div GOFF : 5V/div GON : 20V/div DEL : 2V/div POSITIVE CHARGE-PUMP REGULATOR LOAD-TRANSIENT RESPONSE (10mA TO 100mA) POSITIVE CHARGE-PUMP REGULATOR LOAD REGULATION MAX17075 toc10 0.05 4ms/div VIN : 5V/div REF : 1V/div AVDD : 10V/div VCOM : 5V/div SUPPLY VOLTAGE (V) MAX17075 toc11 2.5 GON (AC-COUPLED) 200mV/div 0V -0.4 -0.8 GON -1.2 LOAD CURRENT 50mA/div -1.6 -0.25 0A -0.30 -2.0 11 12 13 14 15 16 17 18 0 10 20 30 40 50 60 70 LOAD CURRENT (mA) NEGATIVE CHARGE-PUMP REGULATOR LINE REGULATION NEGATIVE CHARGE-PUMP REGULATOR LOAD REGULATION OUTPUT ERROR (%) 0 NEGATIVE CHARGE-PUMP REGULATOR LOAD-TRANSIENT RESPONSE (10mA TO 100mA) MAX17075 toc15 0.2 MAX17075 toc13 0.2 4s/div 80 SUPPLY VOLTAGE (V) MAX17075 toc14 OUTPUT ERROR (%) VIN REF AVDD 3.0 0.5 OUTPUT ERROR (%) MAX17075 Boost Regulator with Integrated Charge Pumps, Switch Control, and High-Current Op Amp GOFF (AC-COUPLED) 100mV/div 0V 0 0A LOAD CURRENT 50mA/div -0.2 -0.2 10.5 11.5 12.5 13.5 14.5 15.5 16.5 17.5 SUPPLY VOLTAGE (V) 8 0 20 40 60 80 100 120 4s/div LOAD CURRENT (mA) _______________________________________________________________________________________ Boost Regulator with Integrated Charge Pumps, Switch Control, and High-Current Op Amp MAX17075 toc18 MAX17075 toc17 MAX17075 toc16 2 100pF LOAD 1 0 0V NO LOAD -2 VVCOM (AC-COUPLED) 200mV/div VPOS 5V/div 0V -1 -3 -4 VVCOM 5V/div -5 -6 IVCOM 50mV/div 0A 0V -7 -8 1k 10k 2s/div 2s/div 100k FREQUENCY (kHz) OPERATIONAL AMPLIFIER LARGE-SIGNAL STEP RESPONSE OPERATIONAL AMPLIFIER SMALL-SIGNAL STEP RESPONSE MAX17075 toc19 MAX17075 toc20 0mV VPOS (AC-COUPLED) 100mV/div 0mV VVCOM (AC-COUPLED) 100mV/div VPOS 5V/div 0V VVCOM 5V/div 0V 40s/div 40s/div HIGH-VOLTAGE SWITCH CONTROL FUNCTION SUP SUPPLY CURRENT vs. SUP SUPPLY VOLTAGE MAX17075 toc21 4.00 MAX17075 toc22 100 3.95 VGON 10V/div 0V VCTL 5V/div 0V 3.90 SUPPLY CURRENT (mA) GAIN (dB) OPERATIONAL AMPLIFIER LOAD-TRANSIENT RESPONSE OPERATIONAL AMPLIFIER RAIL-TO-RAIL INPUT/OUPUT WAVEFORMS OPERATION AMPLIFIER FREQUENCY RESPONSE NO SWITCHING 3.85 3.80 3.75 3.70 3.65 3.60 3.55 3.50 10s/div 6 8 10 12 14 16 18 SUPPLY VOLTAGE (V) _______________________________________________________________________________________ 9 MAX17075 Typical Operating Characteristics (continued) (TA = +25C, unless otherwise noted.) Boost Regulator with Integrated Charge Pumps, Switch Control, and High-Current Op Amp MAX17075 Pin Description PIN NAME 1 POS FUNCTION 2 NEG Operational Amplifier Inverting Input 3 OUT Operational Amplifier Output 4 BGND Analog Ground for Operational Amplifier and Charge Pump. Connect to AGND underneath the IC. 5 SUP Operational Amplifier and Charge-Pump Supply Input. Connect this pin to the output of the boost regulator (AVDD) and bypass to BGND with a minimum1F capacitor. 6 DRVP 7 DRVN Operational Amplifier Noninverting Input Positive Charge-Pump Driver Output Negative Charge-Pump Driver Output High-Voltage Switch Control Input. When CTL is high, the switch between GON and SRC is on and the switch between GON and DRN is off. When CTL is low, the switch between GON and DRN is on and the switch between GON and SRC is off. CTL is inhibited by VCC UVLO and when DEL is less than 1.25V. 8 CTL 9 RST Reset Output. RST is an open-drain output. 10 FBP Positive Charge-Pump Regulator Feedback Input. Connect FBP to the center of a resistive voltagedivider between the positive charge-pump regulator output and AGND to set the positive charge-pump regulator output voltage. Place the resistive voltage-divider within 5mm of FBP. 11 FBN Negative Charge-Pump Regulator Feedback Input. Connect FBN to the center of a resistive voltagedivider between the negative output and REF to set the negative charge-pump regulator output voltage. Place the resistive voltage-divider within 5mm of FBN. 12 REF Reference Output. Connect a 0.22F capacitor from REF to AGND. All power outputs are disabled until REF exceeds its UVLO threshold. 13 VCC Supplies the Internal Reference and Other Internal Circuitry. Connect VCC to the input supply voltage and bypass VCC to AGND with a minimum 1F ceramic capacitor. 14 AGND Analog Ground for Step-Up Regulator and Linear Regulators. Connect to power ground (PGND) underneath the IC. 15 RSTIN Reset Input. Connect to the center of a resistor-divider from VIN. 16 COMP Compensation Pin for Error Amplifier. Connect a series RC from COMP to AGND. 17 FB 18, 19 PGND 20 LX 10 Step-Up Regulator Feedback Input. Connect FB to the center of a resistive voltage-divider between the step-up regulator output and AGND to set the regulator's output voltage. Place the resistive voltagedivider within 5mm of FB. Power Ground Step-Up Regulator Switching Node. Connect inductor and catch diode here and minimize trace area for lowest EMI power ground. 21 DRN Switch Input. Drain of the internal high-voltage back-to-back p-channel FET connects to COM. 22 COM Internal High-Voltage MOSFET Switch Common Terminal 23 SRC Switch Input. Source of the internal high-voltage pFET. Bypass SRC to PGND with a minimum 0.1F capacitor close to the pin. 24 DEL High-Voltage Switch Delay Input. Connect a capacitor from DEL to AGND to set delay. -- EP Exposed Pad. Connect to AGND. ______________________________________________________________________________________ Boost Regulator with Integrated Charge Pumps, Switch Control, and High-Current Op Amp C2 10F 6.3V C1 10F 6.3V R1 10 C5 1F TO VCOM C3 10F 25V VCC LX PGND OUT FB NEG VAVDD D1 MAX17075 VAVDD 13V/500mA R8 187k FROM SYSTEM 3.3V R10 100k R9 20k COMP C12 220pF R3 100k VIN R13 10k R11 RST RSTIN POS REF R6 13.7k C4 10F 25V MAX17075 L1 3.0H VIN 2.5V TO 5.5V (4.5 TO 5.5V FOR FULL LOAD) R14 1k VAVDD DRN C9 0.22F SRC C13 0.01F VGON 30V/20mA COM AGND R12 20k C14 1F C15 0.1F D2 VAVDD FBN R7 100k VGOFF -7V/20mA DRVP D4 C16 1F C17 0.1F C11 0.1F DRVN C10 1F D3 BGND FBP EP SUP VAVDD R15 464k CTL DEL C8 0.033F C6 1F R16 20k FROM TCON Figure 1. Typical Operating Circuit Typical Operating Circuit The typical operating circuit (Figure 1) of the MAX17075 is a complete power-supply system for TFT LCD panels in monitors and TVs. The circuit generates a +13V source driver supply, a +30V positive gate-driver supply, and a -7V negative gate-driver supply from a +2.5V to +5.5V input supply. Table 1 lists some selected components, and Table 2 lists the contact information for component suppliers. ______________________________________________________________________________________ 11 MAX17075 Boost Regulator with Integrated Charge Pumps, Switch Control, and High-Current Op Amp VVCC LX SUP VAVDD POS BOOST CONTROLLER NEG PGND OUT BGND FB COMP SRC DEL VGON COM MAX17075 OSC DRN VVCC VVCC SWITCH CONTROL VCC CTL FROM TCON RSTIN SEQUENCE RST REF REF VAVDD AGND FBN DRVP NEGATIVE CHARGE PUMP VGOFF POSITIVE CHARGE PUMP DRVN POUT FBP SUP VAVDD Figure 2. Functional Diagram Detailed Description The MAX17075 contains a step-up switching regulator to generate the source driver supply, and two chargepump regulators to generate the gate-driver supplies. Each regulator features adjustable output voltage, digital soft-start, and timer-delayed fault protection. The step-up regulator uses fixed-frequency current-mode control architecture. The MAX17075 also includes one 12 high-performance operational amplifier designed to drive the LCD backplane (VCOM). The amplifier features high output current, fast slew rate (45V/s), wide bandwidth (20MHz), and rail-to-rail outputs. In addition, the MAX17075 features a high-voltage switch-control block, a 1.25V reference output, well-defined power-up and power-down sequences, and thermal-overload protection. Figure 2 shows the MAX17075 functional block diagram. ______________________________________________________________________________________ Boost Regulator with Integrated Charge Pumps, Switch Control, and High-Current Op Amp DESIGNATION DESCRIPTION C1, C2 10F 20%, 6.3V X5R ceramic capacitors (0603) Murata GRM188R60J106M TDK C1608X5R0J106M C3, C4, C7 10F 20%, 25V X5R ceramic capacitors (1206) Murata GRM31CR61E106M TDK C3216X5R1E106M C10, C14 1F 10%, 50V X7R ceramic capacitors (1206) Murata GRM31MR71H105KA TDK C3216X7R1H105K DESIGNATION DESCRIPTION C11, C15, C16, C17 0.1F 10%, 50V X7R ceramic capacitors (0603) Murata GRM188R71H104K TDK C1608X7R1H104K D1 3A, 30V Schottky diode (M-Flat) Toshiba CMS02 (TE12L,Q) (Top mark S2) 220mA, 100V dual diodes (SOT23) Fairchild MMBD4148SE (Top mark D4) D2, D3, D4 3.0H, 3ADC inductor Sumida CDRH6D28-3R0 L1 Table 2. Component Suppliers SUPPLIER PHONE FAX WEBSITE Fairchild Semiconductor 408-822-2000 408-822-2102 Sumida 847-545-6700 847-545-6720 www.fairchildsemi.com www.sumida.com TDK 847-803-6100 847-390-4405 www.component.tdk.com Toshiba 949-455-2000 949-859-3963 www.toshiba.com/taec Main Step-Up Regulator The main step-up regulator employs a current-mode, fixed-frequency PWM architecture to maximize loop bandwidth and provide fast-transient response to pulsed loads that are typical for TFT LCD panel source drivers. The 1.2MHz switching frequency allows the use of low-profile inductors and ceramic capacitors to minimize the thickness of LCD panel design. The integrated high-efficiency MOSFET and the built-in digital soft-start function reduce the number of external components required while controlling inrush currents. The output voltage can be set from VIN to 18V with an external resistive voltage-divider. The regulator controls the output voltage and the power delivered to the output by modulating the duty cycle (D) of the internal power MOSFET in each switching cycle. The duty cycle of the MOSFET is approximated by: V - VIN D AVDD VAVDD where VAVDD is the output voltage of the step-up regulator. Figure 3 shows the functional diagram of the step-up regulator. An error amplifier compares the signal at FB to 1.25V and changes the COMP output. The voltage at COMP sets the peak inductor current. As the load varies, the error amplifier sources or sinks current to the COMP output accordingly to produce the inductor peak CLOCK LX LOGIC AND DRIVER PGND CURRENT-LIMIT COMPARATOR SOFTSTART ILIMIT SLOPE COMP OSCILLATOR PWM COMPARATOR CURRENT SENSE ERROR AMP TO FAULT LOGIC MAX17075 FB FAULT COMPARATOR 1.0V 1.25V COMP Figure 3. Step-Up Regulator Functional Diagram current necessary to service the load. To maintain stability at high duty cycles, a slope-compensation signal is summed with the current-sense signal. ______________________________________________________________________________________ 13 MAX17075 Table 1. Component List MAX17075 Boost Regulator with Integrated Charge Pumps, Switch Control, and High-Current Op Amp On the rising edge of the internal clock, the controller sets a flip-flop, turning on the n-channel MOSFET and applying the input voltage across the inductor. The current through the inductor ramps up linearly, storing energy in its magnetic field. Once the sum of the current-feedback signal and the slope compensation exceed the COMP voltage, the controller resets the flip-flop and turns off the MOSFET. Since the inductor current is continuous, a transverse potential develops across the inductor that turns on the diode (D1). The voltage across the inductor then becomes the difference between the output voltage and the input voltage. This discharge condition forces the current through the inductor to ramp back down, transferring the energy stored in the magnetic field to the output capacitor and the load. The MOSFET remains off for the rest of the clock cycle. The error amplifier compares the feedback signal (FBP) with a 1.25V internal reference. If the feedback signal is below the reference, the charge-pump regulator turns on P1 and turns off N1 when the rising edge of the oscillator clock arrives, level shifting C15 and C17 by VSUP volts. If the voltage across CPOUT plus a diode drop (VPOUT + VDIODE) is smaller than the level-shifted flying capacitor voltage (VC17 + VSUP), charge flows from C17 to CPOUT until diode D3-1 turns off. Similarly, if the voltage across C16 plus a diode drop (VC16 + VDIODE) is smaller than the level-shifted flying capacitor voltage (VC15 + VSUP), charge flows from C15 to C16 until diode D2-1 turns off. The falling edge of the oscillator clock turns off P1 and turns on N1, allowing VSUP to charge up the flying capacitor C15 through D2-2 and C16 to charge C17 through diode D3-2. If the feedback signal is above the reference when the rising edge of the oscillator comes, the regulator ignores this clock edge and keeps N1 on and P1 off. Positive Charge-Pump Regulator The positive charge-pump regulator is typically used to generate the positive supply rail for the TFT LCD gatedriver ICs. The output voltage is set with an external resistive voltage-divider from its output to GND with the midpoint connected to FBP. The number of chargepump stages and the setting of the feedback divider determine the output voltage of the positive chargepump regulator. The charge pump includes a high-side p-channel MOSFET (P1) and a low-side n-channel MOSFET (N1) to control the power transfer as shown in Figure 4. The MAX17075 also monitors the FBP voltage for undervoltage conditions. If the VFBP is continuously below 80% of the nominal regulation voltage for approximately 50ms, the MAX17075 sets a fault latch, shutting down all outputs except REF. Once the fault condition is removed, cycle the input voltage (below the UVLO falling threshold) to clear the fault latch and reactivate the device. INPUT SUPPLY SUP MAX17075 C6 OSC REF 1.25V D2-2 P1 ERROR AMPLIFIER C15 D2-1 DRVP C17 D3-2 C16 D3-1 N1 POUT C14 POSITIVE CHARGE-PUMP REGULATOR FBP Figure 4. Positive Charge-Pump Regulator Block Diagram 14 ______________________________________________________________________________________ Boost Regulator with Integrated Charge Pumps, Switch Control, and High-Current Op Amp turns off. The falling edge of the oscillator clock turns off N2 and turns on P2, allowing VSUP to charge up flying capacitor C11 through diode D4-1. If the feedback signal is below the reference when the rising edge of the oscillator comes, the regulator ignores this clock edge and keeps P2 on and N2 off. The MAX17075 also monitors the FBN voltage for undervoltage conditions. If the VFBN is continuously below 80% of the nominal regulation voltage (VREF VFBN) for approximately 50ms, the MAX17075 sets a fault latch, shutting down all outputs except REF. Once the fault condition is removed, cycle the input voltage (below the UVLO falling threshold) to clear the fault latch and reactivate the device. Operational Amplifiers The MAX17075 has one operational amplifier. The operational amplifier is typically used to drive the LCD backplane (VCOM) or the gamma-correction divider string. It features 500mA output short-circuit current, 45V/s slew rate, and 20MHz, 3dB bandwidth. INPUT SUPPLY MAX17075 SUP OSC P2 DRVN REF 0.25V ERROR AMPLIFIER C11 D4-1 D4-2 GOFF C10 N2 R7 NEGATIVE CHARGE-PUMP REGULATOR FBN R6 REF Figure 5. Negative Charge-Pump Regulator Block Diagram ______________________________________________________________________________________ 15 MAX17075 Negative Charge-Pump Regulator The negative charge-pump regulator is typically used to generate the negative supply rail for the TFT LCD gate driver ICs. The output voltage is set with an external resistive voltage-divider from its output to REF with the midpoint connected to FBN. The number of chargepump stages and the setting of the feedback divider determine the output of the negative charge-pump regulator. The charge-pump controller includes a high-side pchannel MOSFET (P2) and a low-side n-channel MOSFET (N2) to control the power transfer as shown in Figure 5. The error amplifier compares the feedback signal (FBN) with a 250mV internal reference. If the feedback signal is above the reference, the charge-pump regulator turns on N2 and turns off P2 when the rising edge of the oscillator clock arrives, level shifting C11. This connects C11 in parallel with reservoir capacitor C10. If the voltage across C10 minus a diode drop (VC10 - VDIODE) is higher than the level-shifted flying capacitor voltage (-VC11), charge flows from C10 to C11 until diode D4-2 MAX17075 Boost Regulator with Integrated Charge Pumps, Switch Control, and High-Current Op Amp Short-Circuit Current Limit and Input Clamp The operational amplifier limits short-circuit current to approximately 500mA if the output is directly shorted to SUP or to BGND. If the short-circuit condition persists, the junction temperature of the IC rises until it reaches the thermal-shutdown threshold (+160C typ). Once the junction temperature reaches the thermalshutdown threshold, an internal thermal sensor immediately sets the thermal fault latch, shutting off all the IC's outputs. The device remains inactive until the input voltage is cycled. The operational amplifier has 4V input clamp structures in series with a 500 resistance and a diode (Figure 6). Driving Pure Capacitive Load The operational amplifier is typically used to drive the LCD backplane (VCOM) or the gamma-correction divider string. The LCD backplane consists of a distributed series capacitance and resistance, a load that can be easily driven by the operational amplifier. However, if the operational amplifier is used in an application with a pure capacitive load, steps must be taken to ensure stable operation. As the operational amplifier's capacitive load increases, the amplifier's bandwidth decreases and gain peaking increases. A 5 to 50 small resistor placed between OUT and the capacitive load reduces peaking, but also reduces the gain. An alternative method of reducing peaking is to place a series RC network (snubber) in parallel with the capacitive load. The RC network does not continuously load the output or reduce the gain. Typical values of the resistor are between 100 and 200, and the typical value of the capacitor is 10nF. High-Voltage Switch Control The MAX17075's high-voltage switch control block (Figure 7) consists of two high-voltage p-channel MOSFETs: Q1, between SRC and COM; and Q2, between COM and DRN. At power-up and only at power up, before the switch control is enabled (a 1.5k pulldown is present on COM). At switch-off, COM is high impedance. The switch control input (CTL) is not activated until all four of the following conditions are satisfied: the input voltage exceeds UVLO, the soft-start routine of all the regulators is complete, there is no fault condition detected, and VDEL exceeds its turn-on threshold. Once activated and if CTL is logic-high, Q1 turns on and Q2 turns off, connecting COM to SRC. When CTL is logic-low, Q1 turns off and Q2 turns on, connecting COM to DRN. VCC 5A MAX17075 DEL 2.25V SUP Q3 FAULT REF_OK SRC POS VREF Q1 4V COM 500 MAX17075 NEG SWITCH CONTROL Q2 1.5k OUT BGND DRN CTL OP AMP INPUT CLAMP STRUCTURE Figure 6. Op Amp Input Clamp Structure 16 Figure 7. Switch Control ______________________________________________________________________________________ Q4 Boost Regulator with Integrated Charge Pumps, Switch Control, and High-Current Op Amp Power-Up Sequence and Soft-Start Once the voltage on V CC exceeds the XAO UVLO threshold of approximately 1.5V, the reference turns on. With a 0.22F REF bypass capacitor, the reference reaches its regulation voltage of 1.25V in approximately 1ms. When the reference voltage exceeds 1V and VCC exceeds its UVLO threshold of approximately 2.25V, the IC enables the main step-up regulator, the gate-on linear-regulator controller, and the gate-off linearregulator controller simultaneously. The IC employs soft-start for each regulator to minimize inrush current and voltage overshoot and to ensure a well-defined startup behavior. Each output uses a 7-bit soft-start DAC. For the step-up and the gate-on linear regulator, the DAC output is stepped in 128 steps from zero up to the reference voltage. For the gate-off linear regulator, the DAC output steps from the reference down to 250mV in 128 steps. The soft-start duration is 10ms (typ) for step-up regulator and 3ms (typ) for gateon and gate-off regulators. When the input voltage falls below the UVLO falling threshold, the controller turns off the main step-up regulator and disables the switch-control block; the operational amplifier output is high impedance. Fault Protection During steady-state operation, if the output of the main regulator or any of the linear-regulator outputs exceed their respective fault-detection thresholds, the MAX17075 activates an internal fault timer. If any condition or combination of conditions indicates a continuous fault for the fault-timer duration (50ms typ), the MAX17075 sets the fault latch to shut down all the outputs except the reference. Once the fault condition is removed, cycle the input voltage (below the UVLO falling threshold) to clear the fault latch and reactivate the device. The fault-detection circuit is disabled during the soft-start time. VREF 1V VAVDD A capacitor (CDEL) from DEL to AGND determines the switch-control-block startup delay. After the input voltage exceeds the UVLO threshold (2.25V typ) and the soft-start routine for each regulator is complete and there is no fault detected, a 5mA current source starts charging CDEL. Once the capacitor voltage exceeds 1.25V (typ), the switch-control block is enabled as shown in Figure 8. After the switch-control block is enabled, COM can be connected to SRC or DRN through the internal p-channel switches, depending upon the state of CTL. Before startup and when VIN is less than UVLO, DEL is internally connected to AGND to discharge CDEL. Select CDEL to set the delay time using the following equation: CDEL = DELAY _ TIME x VVCC 2.25V 1.5V 14ms SOFT-START VCOM 3ms SOFT-START VPOUT 5A 1.25V 1.25V VGOFF VDEL Undervoltage Lockout (UVLO) The UVLO circuit compares the input voltage at VCC with the UVLO threshold (2.25V rising, 2.20V falling, typ) to ensure the input voltage is high enough for reliable operation. The 50mV (typ) hysteresis prevents supply transients from causing a restart. Once the input voltage exceeds the UVLO rising threshold, startup begins. VGON SOFT-START BEGINS INPUT VOLTAGE OK SWITCH CONTROL ENABLED Figure 8. Power-Up Sequence ______________________________________________________________________________________ 17 MAX17075 Reference Voltage (REF) The reference voltage is nominally 1.25V, and can source at least 50A (see the Typical Operating Characteristics). VCC is the input of the internal reference block. Bypass REF with a 0.22F ceramic capacitor connected between REF and AGND. MAX17075 Boost Regulator with Integrated Charge Pumps, Switch Control, and High-Current Op Amp Thermal-Overload Protection Thermal-overload protection prevents excessive power dissipation from overheating the MAX17075. When the junction temperature exceeds +160C, a thermal sensor immediately activates the fault protection, which shuts down all outputs except the reference, allowing the device to cool down. Once the device cools down by approximately 15C, cycle the input voltage (below the UVLO falling threshold) to clear the fault latch and reactivate the device. The thermal-overload protection protects the controller in the event of fault conditions. For continuous operation, do not exceed the absolute maximum junction temperature rating of +150C. XAO Voltage Detector Based upon the input at the RSTIN and VCC pins, the XAO controller either pulls the reset pin RST low or sets it to high impedance. RST is an open-drain output. Pull it high to system 3.3V through a 10k resistor. Connect RSTIN to VIN through resistor-dividers R11 and R12 (Figure 1) to set the proper XAO threshold. Once VCC voltage exceeds approximately 2.25V, the controller initiates a 220ms blanking period during which the drop on VCC is ignored and RST is set to high impedance. After this blanking period and if RSTIN goes below approximately 1.25V, RST is pulled low indicating low RSTIN input. RST stays low until VCC falls below approximately 1V. Then RST cannot be held low any more. The controller gives up and RST is pulled up by the external resister. A 50mV hysteresis is implemented for XAO threshold. Design Procedure Step-Up Regulator Inductor Selection The minimum inductance value, peak current rating, and series resistance are factors to consider when selecting the inductor. These factors influence the converter's efficiency, maximum output load capability, transient-response time, and output voltage ripple. Size and cost are also important factors to consider. The maximum output current, input voltage, output voltage, and switching frequency determine the inductor value. Very high inductance values minimize the current ripple, and therefore reduce the peak current, which decreases core losses in the inductor and conduction losses in the entire power path. However, large inductor values also require more energy storage and more turns of wire, which increase size and can increase conduction losses in the inductor. Low inductance values decrease the size, but increase the current ripple and 18 peak current. Finding the best inductor involves choosing the best compromise between circuit efficiency, inductor size, and cost. The equations used here include a constant LIR, which is the ratio of the inductor peak-to-peak ripple current to the average DC inductor current at the full load current. The best trade-off between inductor size and circuit efficiency for step-up regulators generally has an LIR between 0.3 and 0.6. However, depending on the AC characteristics of the inductor core material and ratio of inductor resistance to other power-path resistances, the best LIR can shift up or down. If the inductor resistance is relatively high, more ripple can be accepted to reduce the number of turns required and increase the wire diameter. If the inductor resistance is relatively low, increasing inductance to lower the peak current can decrease losses throughout the power path. If extremely thin high-resistance inductors are used, as is common for LCD-panel applications, the best LIR can increase to between 0.5 and 1.0. Once a physical inductor is chosen, higher and lower values of the inductor should be evaluated for efficiency improvements in typical operating regions. Calculate the approximate inductor value using the typical input voltage (VIN), the maximum output current (IMAIN(MAX)), and the expected efficiency (TYP) taken from an appropriate curve in the Typical Operating Characteristics section, and an estimate of LIR based on the above discussion: 2 V VAVDD - VIN TYP L AVDD = IN VAVDD IAVDD(MAX) x fSW LIR Choose an available inductor value from an appropriate inductor family. Calculate the maximum DC input current at the minimum input voltage (VIN(MIN)) using conservation of energy and the expected efficiency at that operating point (MIN) taken from the appropriate curve in the Typical Operating Characteristics: IIN(DC,MAX) = IAVDD(MAX) x VAVDD VIN(MIN) x MIN Calculate the ripple current at that operating point and the peak current required for the inductor: IAVDD _ RIPPLE = ( VIN(MIN) x VAVDD - VIN(MIN) L AVDD x VAVDD x fSW IAVDD _ PEAK = IIN(DC,MAX) + IAVDD _ RIPPLE ______________________________________________________________________________________ 2 ) Boost Regulator with Integrated Charge Pumps, Switch Control, and High-Current Op Amp Considering the typical operating circuit, the maximum load current (IAVDD(MAX)) is 500mA with a 13V output and a typical input voltage of 5V. Choosing an LIR of 0.5 and estimating efficiency of 85% at this operating point: 2 85 5V 13V - 5V 0.8 L AVDD = 3.35H 13V 0.5A x 1.2MHz 0.5 Using the circuit's minimum input voltage (2.5V) and estimating efficiency of 80% at that operating point: IIN(DC,MAX) = 0.5A x 13V 3.25A 2.5V x 0.8 The ripple current and the peak current are: IRIPPLE = 2.5V x (13V - 2.5V ) 0.51A 3.3H x 13V x 1.2MHz IPEAK = 3.25A + 0.51A 3.51A 2 Output Capacitor Selection The total output voltage ripple has two components: the capacitive ripple caused by the charging and discharging of the output capacitance, and the ohmic ripple due to the capacitor's equivalent series resistance (ESR): VAVDD _ RIPPLE = VAVDD _ RIPPLE(C) + VAVDD _ RIPPLE(ESR) V I - VIN VAVDD _ RIPPLE(C) AVDD AVDD , CAVDD VAVDDfSW and VAVDD _ RIPPLE(ESR) IPEAKRESR _ AVDD where I PEAK is the peak inductor current (see the Inductor Selection section). For ceramic capacitors, the output voltage ripple is typically dominated by VAVDD_RIPPLE(C). The voltage rating and temperature characteristics of the output capacitor must also be considered. Input-Capacitor Selection The input capacitor (CIN) reduces the current peaks drawn from the input supply and reduces noise injection into the IC. Two 10F ceramic capacitors are used in the typical operating circuit (Figure 1) because of the high source impedance seen in typical lab setups. Actual applications usually have much lower source impedance since the step-up regulator often runs directly from the output of another regulated supply. Typically, CIN can be reduced below the values used in the typical operating circuit. Ensure a low-noise supply at VCC by using adequate CIN. Alternately, greater voltage variation can be tolerated on CIN if VCC is decoupled from CIN using an RC lowpass filter (see R1 and C5 in Figure 1). Rectifier Diode The MAX17075's high switching frequency demands a high-speed rectifier. Schottky diodes are recommended for most applications because of their fast recovery time and low forward voltage. In general, a 2A Schottky diode complements the internal MOSFET well. Output Voltage Selection The output voltage of the step-up regulator can be adjusted by connecting a resistive voltage-divider from the output (VAVDD) to ground with the center tap connected to FB (see Figure 1). Select R9 in the 10k to 50k range. Calculate R8 with the following equation: V R8 = R9 x AVDD - 1 VFB where VFB, the step-up regulator's feedback set point, is 1.25V. Place R8 and R9 close to the IC. Loop Compensation Choose RCOMP (R10 in Figure 1) to set the high-frequency integrator gain for fast-transient response. Choose CCOMP (C12 in Figure 1) to set the integrator zero to maintain loop stability. For low-ESR output capacitors, use the following equations to obtain stable performance and good transient response: RCOMP 312.5 x VIN x VAVDD x CAVDD L AVDD x IAVDD(MAX) CCOMP VAVDD x CAVDD 10 x IAVDD(MAX)RCOMP ______________________________________________________________________________________ 19 MAX17075 The inductor's saturation current rating and the MAX17075's LX current limit should exceed IAVDD_PEAK, and the inductor's DC current rating should exceed IIN(DC,MAX). For good efficiency, choose an inductor with less than 0.1 series resistance. MAX17075 Boost Regulator with Integrated Charge Pumps, Switch Control, and High-Current Op Amp To further optimize transient response, vary RCOMP in 20% steps and CCOMP in 50% steps while observing transient-response waveforms. Charge-Pump Regulators Selecting the Number of Charge-Pump Stages For highest efficiency, always choose the lowest number of charge-pump stages that meet the output requirement. The number of positive charge-pump stages is given by: V + VDROPOUT - VAVDD POS = GON VSUP - 2 x VD where nPOS is the number of positive charge-pump stages, VGON is the output of the positive charge-pump regulator, VSUP is the supply voltage of the chargepump regulators, VD is the forward voltage drop of the charge-pump diode, and V DROPOUT is the dropout margin for the regulator. Use VDROPOUT = 600mV. The number of negative charge-pump stages is given by: NEG = - VGOFF + VDROPOUT VSUP - 2 x VD where nNEG is the number of negative charge-pump stages and VGOFF is the output of the negative chargepump regulator. The above equations are derived based on the assumption that the first stage of the positive charge pump is connected to VAVDD and the first stage of the negative charge pump is connected to ground. Flying Capacitors Increasing the flying capacitor CX (connected to DRVN and DRVP) value lowers the effective source impedance and increases the output current capability. Increasing the capacitance indefinitely has a negligible effect on output current capability because the internal switch resistance and the diode impedance place a lower limit on the source impedance. A 0.1F ceramic capacitor works well in most low-current applications. The flying capacitor's voltage rating must exceed the following: VCX > n x VSUP where n is the stage number in which the flying capacitor appears. Charge-Pump Output Capacitor Increasing the output capacitance or decreasing the ESR reduces the output ripple voltage and the peak-topeak transient voltage. With ceramic capacitors, the output voltage ripple is dominated by the capacitance value. Use the following equation to approximate the required capacitor value: COUT _ CP ILOAD _ CP 2fOSCVRIPPLE _ CP where COUT_CP is the output capacitor of the charge pump, I LOAD _ CP is the load current of the charge pump, and VRIPPLE_CP is the peak-to-peak value of the output ripple, and fOSC is the switching frequency. Output Voltage Selection Adjust the positive charge-pump regulator's output voltage by connecting a resistive voltage-divider from the REG P output to GND with the center tap connected to FBP (Figure 1). Select the lower resistor of divider R16 in the 10k to 30k range. Calculate the upper resistor R15 with the following equation: V R15 = R16 x GON - 1 VFBP where VFBP = 1.25V (typical). Adjust the negative charge-pump regulator's output voltage by connecting a resistive voltage-divider from VGOFF to REF with the center tap connected to FBN (Figure 1). Select R6 in the 35k to 68k range. Calculate R7 with the following equation: V - VGOFF R7 = R6 x FBN VREF - VFBN where VFBN = 250mV, VREF = 1.25V. Note that REF can only source up to 50A, using a resistor less than 35k for R6 results in higher bias current than REF can supply. Set the XAO Threshold Voltage XAO threshold voltage can be adjusted by connecting a resistive voltage-divider from input VIN to GND with the center tap connected to RSTIN (see Figure 1). Select R12 in the 10k to 50k range. Calculate R11 with the following equation: V R11 = R12 x INXAO - 1 VRSTIN where VRSTIN, the RSTIN threshold set point, is 1.25V. VINXAO is the desired XAO threshold voltage. Place R11 and R12 close to the IC. 20 ______________________________________________________________________________________ Boost Regulator with Integrated Charge Pumps, Switch Control, and High-Current Op Amp the operational amplifier divider ground connections, the COMP and DEL capacitor ground connections, and the device's exposed backside paddle. Connect the AGND and PGND islands by connecting the PGND pin directly to the exposed backside paddle. Make no other connections between these separate ground planes. Careful PCB layout is important for proper operation. Use the following guidelines for good PCB layout: * Minimize the area of high-current loops by placing the inductor, the output diode, and the output capacitors near the input capacitors and near the LX and PGND pins. The high-current input loop goes from the positive terminal of the input capacitor to the inductor, to the IC's LX pin, out of PGND, and to the input capacitor's negative terminal. The high-current output loop is from the positive terminal of the input capacitor to the inductor, to the output diode (D1), and to the positive terminal of the output capacitors, reconnecting between the output capacitor and input capacitor ground terminals. Connect these loop components with short, wide connections. * Avoid using vias in the high-current paths. If vias are unavoidable, use many vias in parallel to reduce resistance and inductance. * Create a power-ground island (PGND) consisting of the input and output capacitor grounds, PGND pin, and any charge-pump components. Connect all these together with short, wide traces or a small ground plane. Maximizing the width of the power ground traces improves efficiency and reduces output voltage ripple and noise spikes. Create an analog ground plane (AGND) consisting of the AGND pin, all the feedback-divider ground connections, * Place all feedback voltage-divider resistors within 5mm of their respective feedback pins. The divider's center trace should be kept short. Placing the resistors far away causes their FB traces to become antennas that can pick up switching noise. Take care to avoid running any feedback trace near LX or the switching nodes in the charge pumps, or provide a ground shield. * Place the VCC pin and REF pin bypass capacitors as close as possible to the device. The ground connection of the VCC bypass capacitor should be connected directly to the AGND pin with a wide trace. * Minimize the length and maximize the width of the traces between the output capacitors and the load for best transient responses. * Minimize the size of the LX node while keeping it wide and short. Keep the LX node away from feedback nodes (FB, FBP, and FBN) and analog ground. Use DC traces to shield if necessary. Refer to the MAX17075 evaluation kit for an example of proper PCB layout. ______________________________________________________________________________________ 21 MAX17075 PCB Layout and Grounding Pin Configuration Chip Information FB COMP RSTIN AGND VCC TOP VIEW PGND PROCESS: S45UR 18 17 16 15 14 13 12 PGND 19 FBN 10 FBP 9 RST SRC 23 8 CTL DEL 24 7 DRVN DRN 21 3 4 5 6 SUP DRVP 2 BGND 1 NEG COM 22 OUT MAX17075 Package Information REF 11 LX 20 POS MAX17075 Boost Regulator with Integrated Charge Pumps, Switch Control, and High-Current Op Amp For the latest package outline information and land patterns (footprints), go to www.maxim-ic.com/packages. Note that a "+", "#", or "-" in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status. PACKAGE TYPE PACKAGE CODE OUTLINE NO. LAND PATTERN NO. 24 TQFN T2444+4 21-0139 90-0022 TQFN 22 ______________________________________________________________________________________ Boost Regulator with Integrated Charge Pumps, Switch Control, and High-Current Op Amp REVISION NUMBER REVISION DATE 0 11/08 1 5/12 DESCRIPTION Initial release Updated Absolute Maximum Ratings PAGES CHANGED -- 2 Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance. 23 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 (c) 2012 Maxim Integrated Products Maxim is a registered trademark of Maxim Integrated Products, Inc. MAX17075 Revision History