MAX1722/MAX1723/ MAX1724 1.5A IQ, Step-Up DC-DC Converters in TSOT and DFN General Description The MAX1722/MAX1723/MAX1724 compact, high-efficiency, step-up DC-DC converters are available in tiny, 5-pin TSOT packages. They feature an extremely low 1.5A quiescent supply current to ensure the highest possible light-load efficiency. Optimized for operation from one to two alkaline or nickel-metal-hydride (NiMH) cells, or a single Li+ cell, these devices are ideal for applications where extremely low quiescent current and ultra-small size are critical. Built-in synchronous rectification significantly improves efficiency and reduces size and cost by eliminating the need for an external Schottky diode. All three devices feature a 0.5 N-channel power switch. The MAX1722/ MAX1724 also feature proprietary noise-reduction circuitry, which suppresses electromagnetic interference (EMI) caused by the inductor in many step-up applications. The family offers different combinations of fixed or adjustable outputs, shutdown, and EMI reduction (see Selector Guide). Applications Pagers Remote Controls Remote Wireless Transmitters Personal Medical Devices Digital Still Cameras Single-Cell BatteryPowered Devices Low-Power Hand-Held Instruments MP3 Players Personal Digital Assistants (PDA) Typical Operating Circuit 10H IN 0.8V TO 5.5V BATT LX MAX1724 ON OUT OFF SHDN GND 19-1735; Rev 5; 8/17 OUT 3.3V AT UP TO 150mA Benefits and Features Up to 90% Efficiency No External Diode or FETs Needed 1.5A Quiescent Supply Current 0.1A Logic-Controlled Shutdown 1% Output Voltage Accuracy Fixed Output Voltage (MAX1724) or Adjustable Output Voltage (MAX1722/MAX1723) Up to 150mA Output Current 0.8V to 5.5V Input Voltage Range 0.91V Guaranteed Startup (MAX1722/MAX1724) Internal EMI Suppression (MAX1722/MAX1724) TSOT Package (0.9mm typ Height) DFN Package (2mm x 2mm x 0.75mm) Ordering Information and Selector Guide appears at end of data sheet. MAX1722/MAX1723/ MAX1724 1.5A IQ, Step-Up DC-DC Converters in TSOT and DFN Absolute Maximum Ratings Operating Temperature Range............................ -40C to +85C Junction Temperature.......................................................+150C Storage Temperature Range............................. -65C to +150C Soldering Temperature Lead(Pb)-free packages...............................................+260C Packages containing lead(Pb)......................................+240C OUT, SHDN, BATT, LX to GND................................-0.3V to +6V FB to GND............................................... -0.3V to (VOUT + 0.3V) OUT, LX Current.......................................................................1A Continuous Power Dissipation (TA = +70C) 5-Pin Thin SOT (derate 2.7mW/C above +70C)....219.10mW Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Electrical Characteristics (VBATT = 1.2V, VOUT = 3.3V (MAX1722/MAX1723), VOUT = VOUT(NOM) (MAX1724), SHDN = OUT, RL = , TA = 0C to +85C, unless otherwise noted. Typical values are at TA = +25C.) (Note 1) PARAMETER SYMBOL Minimum Input Voltage Operating Input Voltage CONDITIONS VIN TA = +25C TA = +25C, RL = 3k Minimum Start-Up Input Voltage MAX1724E__27 MAX1724E__30 Output Voltage VOUT MAX1724E__33 MAX1724E__50 VOUT MAX1722/MAX1723 Feedback Voltage VFB MAX1722/MAX1723 Feedback Bias Current IFB MAX1722/MAX1723 RDS(ON) VOUT forced to 3.3V ILIM VOUT forced to 3.3V Synchronous Rectifier ZeroCrossing Current VOUT forced to 3.3V Quiescent Current into OUT (Notes 3, 4) Shutdown Current into OUT MAX1723/MAX1724 (Notes 3, 4) Quiescent Current into BATT MAX1722/MAX1724 (Note 4) Output Voltage Range N-Channel OnResistance P-Channel OnResistance N-Channel Switch Current Limit Switch Maximum OnTime www.maximintegrated.com MIN MAX1722/MAX1724 RDS(ON) tON TYP MAX 0.8 V MAX1722/MAX1724 0.91 5.5 MAX1723 (Note 2) 1.2 5.5 MAX1722/MAX1724 0.83 0.91 MAX1723 (Note 2) 0.87 1.2 2.7 2.727 TA = +25C 2.673 TA = +25C 2.970 TA = +25C 3.267 TA = +25C 4.950 TA = 0C to +85C 2.633 TA = 0C to +85C 2.925 TA = 0C to +85C 3.218 TA = 0C to +85C 4.875 TA = +25C 1.223 TA = 0C to +85C VOUT forced to 3.3V 3.0 3.075 3.3 3.333 5.050 5.125 5.5 1.235 1.247 1.260 1.5 20 2.2 V V nA 0.5 1.0 1.0 2.0 400 500 600 mA 3.5 5 6.5 s 5 20 35 mA A 1.5 3.6 0.01 0.5 TA = +25C 0.001 TA = +85C V 3.383 5.0 TA = +25C TA = +85C V 3.030 1.210 TA = +25C V 2.767 2 TA = +85C UNITS 0.1 0.01 0.5 A A Maxim Integrated 2 MAX1722/MAX1723/ MAX1724 1.5A IQ, Step-Up DC-DC Converters in TSOT and DFN Electrical Characteristics (continued) (VBATT = 1.2V, VOUT = 3.3V (MAX1722/MAX1723), VOUT = VOUT(NOM) (MAX1724), SHDN = OUT, RL = , TA = 0C to +85C, unless otherwise noted. Typical values are at TA = +25C.) (Note 1) PARAMETER SYMBOL Shutdown Current into BATT CONDITIONS MAX1724 (Note 4) VIL SHDN Voltage Threshold VIH MAX1723/MAX1724 TA = +25C TA = +85C TYP MAX 0.001 0.5 0.01 75 MAX1723/MAX1724 MAX1723/MAX1724, VSHDN = 5.5V SHDN Input Bias Current MIN TA = +25C TA = +85C 400 500 800 2 100 7 UNITS A mV nA Electrical Characteristics (VBATT = 1.2V, VOUT = 3.3V (MAX1722/MAX1723), VOUT = VOUT(NOM) (MAX1724), SHDN = OUT, RL = , TA = -40C to +85C, unless otherwise noted.) (Note 1) PARAMETER SYMBOL CONDITIONS MIN TYP MAX MAX1724E__27 2.633 2.767 MAX1724E__30 2.925 3.075 MAX1724E__33 3.218 3.383 MAX1724E__50 4.875 5.125 UNITS V Output Voltage VOUT Output Voltage Range VOUT MAX1722/MAX1723 2 5.5 V VFB MAX1722/MAX1723 1.200 1.270 V RDS(ON) VOUT forced to 3.3V 1.0 RDS(ON) ILIM VOUT forced to 3.3V VOUT forced to 3.3V VOUT forced to 3.3V Feedback Voltage N-Channel On-Resistance P-Channel On-Resistance N-Channel Switch Current Limit Switch Maximum On-Time tON Synchronous Rectifier ZeroCrossing Current Quiescent Current into OUT SHDN Voltage Threshold 2.0 400 620 mA 3.5 6.5 s 5 35 mA 3.6 A (Notes 3,4) VIL VIH MAX1723/MAX1724 MAX1723/MAX1724 75 800 mV Note 1: Limits are 100% production tested at TA = +25C. Limits over the operating temperature range are guaranteed by design. Note 2: Guaranteed with the addition of a Schottky MBR0520L external diode between LX and OUT when using the MAX1723 with only one cell, and assumes a 0.3V voltage drop across the Schottky diode (see Figure 3). Note 3: Supply current is measured with an ammeter between the output and OUT pin. This current correlates directly with actual battery supply current, but is reduced in value according to the step-up ratio and efficiency. Note 4: VOUT forced to the following conditions to inhibit switching: VOUT = 1.05 x VOUT(NOM) (MAX1724), VOUT = 3.465V (MAX1722/MAX1723). www.maximintegrated.com Maxim Integrated 3 MAX1722/MAX1723/ MAX1724 1.5A IQ, Step-Up DC-DC Converters in TSOT and DFN Typical Operating Characteristics (Figure 3 (MAX1723), Figure 7 (MAX1722), Figure 8 (MAX1724), VBATT = VIN = 1.5V, L = 10H, CIN = 10F, COUT = 10F, TA = +25C, unless otherwise noted.) 80 70 VIN = 1.5V 0.1 L = DO1606 1 10 70 100 50 1000 0.01 0.1 L = DO1606 1 10 100 MAX1722 toc03 VIN = 1.5V 70 60 VIN = 1.0V VIN = 1.5V VIN = 2.0V 80 1000 VIN = 1.0V 50 0.01 0.1 1 L = DO1606 10 100 MAXIMUM OUTPUT CURRENT vs. INPUT VOLTAGE STARTUP VOLTAGE vs. LOAD CURRENT QUIESCENT CURRENT INTO OUT vs. OUTPUT VOLTAGE VOUT = 5.0V 80 VOUT = 3.3V RESISTIVE LOAD VOUT = 5.0V 2.2 40 2.0 1.8 1.6 1.4 1.2 1.0 0.8 2 3 4 5 0.01 STARTUP VOLTAGE vs. TEMPERATURE STARTUP VOLTAGE (V) 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.1 1 10 LOAD CURRENT (mA) 100 0 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 OUTPUT VOLTAGE (V) SWITCHING WAVEFORMS MAX1722 toc07 NO LOAD 1.0 NO LOAD 0.2 INPUT VOLTAGE (V) 1.2 1.8 MAX1722 toc08 1 0.6 2.0 MAX1722 toc05 MAX1722 toc04 2.4 1000 MAX1722 toc06 LOAD CURRENT (mA) VOUT = 2.5V 0 90 LOAD CURRENT (mA) 120 0 100 QUIESCENT CURRENT (A) IOUT(MAX) (mA) 80 EFFICIENCY vs. LOAD CURRENT (VOUT = 2.5V) LOAD CURRENT (mA) 200 160 VIN = 2.5V 60 STARTUP VOLTAGE (V) 0.01 VIN = 2.0V 90 VIN = 1.0V 60 50 100 EFFICIENCY (%) VIN = 4.0V EFFICIENCY (%) VIN = 2.0V 90 EFFICIENCY (%) VIN = 3.3V MAX1722 toc01 100 EFFICIENCY vs. LOAD CURRENT (VOUT = 3.3V) MAX1722 toc02 EFFICIENCY vs. LOAD CURRENT (VOUT = 5.0V) 0.8 ILX 500mA/div VOUT 50mV/div 0.6 0.4 VLX 2V/div 0.2 0 -40 -15 10 35 TEMPERATURE (C) www.maximintegrated.com 60 85 1s/div IOUT = 50mA, VOUT = 5.0V, VIN = 3.3V Maxim Integrated 4 MAX1722/MAX1723/ MAX1724 1.5A IQ, Step-Up DC-DC Converters in TSOT and DFN Typical Operating Characteristics (continued) (Figure 3 (MAX1723), Figure 7 (MAX1722), Figure 8 (MAX1724), VBATT = VIN = 1.5V, L = 10H, CIN = 10F, COUT = 10F, TA = +25C, unless otherwise noted.) 3.3V MAX1722 toc10 SHUTDOWN RESPONSE MAX1722 toc09 LOAD-TRANSIENT RESPONSE 5V A VOUT 2V/div 0 50mA 2V B 0 VSHDN 1V/div 0 A: VOUT, 50mV/div B: IOUT, 20mA/div 200s/div 1ms/div VIN = 3.3V, VOUT = 5.0V, ROUT = 100 SHUTDOWN INPUT THRESHOLD vs. TEMPERATURE MAX1722 toc11 SHUTDOWN THRESHOLD (mV) 0.8 0.7 0.6 RISING EDGE 0.5 0.4 FALLING EDGE 0.3 0.2 0.1 0 -40 -15 10 35 60 85 TEMPERATURE (C) www.maximintegrated.com Maxim Integrated 5 MAX1722/MAX1723/ MAX1724 1.5A IQ, Step-Up DC-DC Converters in TSOT and DFN Pin Configurations TOP VIEW BATT + 1 5 LX SHDN MAX1722 GND 2 1 GND 2 FB 3 TSOT FB 1 BATT 2 GND 3 LX BATT 1 MAX1723 FB 3 OUT 4 5 GND 2 4 OUT SHDN MAX1722 6 OUT 5 N.C. 4 LX FB 1 SHDN 2 GND 3 DFN MAX1723 LX 4 OUT 6 OUT 5 N.C. 4 LX MAX1724 3 TSOT 5 TSOT 6 OUT SHDN 1 5 N.C. BATT 2 4 LX GND 3 DFN MAX1724 DFN Pin Description PIN TSOT NAME uDFN MAX1722 MAX1723 MAX1724 MAX1722 MAX1723 MAX1724 1 -- 1 2 -- 2 BATT -- 1 3 -- 2 1 SHDN 2 2 2 3 3 3 GND FUNCTION Battery Input and Damping Switch Connection Shutdown Input. Drive high for normal operation. Drive low for shutdown. Ground 3 3 -- 1 1 -- FB Feedback Input to Set Output Voltage. Use a resistor-divider network to adjust the output voltage. See Setting the Output Voltage section. 4 4 4 6 6 6 OUT Power Output. OUT also provides bootstrap power to the IC. 5 5 5 4 4 4 LX Internal N-channel MOSFET Switch Drain and P-Channel Synchronous Rectifier Drain -- -- -- 5 5 5 N.C. www.maximintegrated.com No connect. Maxim Integrated 6 MAX1722/MAX1723/ MAX1724 1.5A IQ, Step-Up DC-DC Converters in TSOT and DFN OUT MAX1723 ZEROCROSSING DETECTOR STARTUP CIRCUITRY P SHDN CONTROL LOGIC DRIVER LX FB ERROR COMPARATOR 1.235V REFERENCE N CURRENT LIMIT GND Figure 1. MAX1723 Simplified Functional Diagram Detailed Description The MAX1722/MAX1723/MAX1724 compact, high-efficiency, step-up DC-DC converters are guaranteed to start up with voltages as low as 0.91V and operate with an input voltage down to 0.8V. Consuming only 1.5A of quiescent current, these devices include a built-in synchronous rectifier that reduces cost by eliminating the need for an external diode and improves overall efficiency by minimizing losses in the circuit (see Synchronous Rectification section). The MAX1722/MAX1724 feature a clamp circuit that reduces EMI due to inductor ringing. The MAX1723/MAX1724 feature an active-low shutdown that reduces quiescent supply current to 0.1A. The MAX1722/MAX1723 have an adjustable output voltage, while the MAX1724 is available with four fixed-output voltage options (see Selector Guide). Figure 1 is the MAX1723 simplified functional diagram and Figure 2 is the MAX1724 simplified functional diagram. PFM Control Scheme A forced discontinuous, current-limited, pulse-frequencymodulation (PFM) control scheme is a key feature of the www.maximintegrated.com MAX1722/MAX1723/MAX1724. This scheme provides ultra-low quiescent current and high efficiency over a wide output current range. There is no oscillator; the inductor current is limited by the 0.5A N-channel current limit or by the 5s switch maximum on-time. Following each on cycle, the inductor current must ramp to zero before another cycle may start. When the error comparator senses that the output has fallen below the regulation threshold, another cycle begins. Synchronous Rectification The internal synchronous rectifier eliminates the need for an external Schottky diode, thus reducing cost and board space. While the inductor discharges, the P-channel MOSFET turns on and shunts the MOSFET body diode. As a result, the rectifier voltage drop is significantly reduced, improving efficiency without the addition of external components. Low-Voltage Startup Circuit The MAX1722/MAX1723/MAX1724 contain a low-voltage startup circuit to control DC-DC operation until the output voltage exceeds 1.5V (typ). The minimum startMaxim Integrated 7 MAX1722/MAX1723/ MAX1724 1.5A IQ, Step-Up DC-DC Converters in TSOT and DFN DAMPING SWITCH BATT OUT MAX1724 ZEROCROSSING DETECTOR STARTUP CIRCUITRY R2 P SHDN CONTROL LOGIC DRIVER ERROR COMPARATOR LX N R1 CURRENT LIMIT 1.235V REFERENCE GND Figure 2. MAX1724 Simplified Functional Diagram 10H 1.2V TO VOUT 10F SHDN LX OUT VOUT = 3.6V R2 2.37M MAX1723 GND D1 10F FB R1 1.24M Figure 3. MAX1723 Single-Cell Operation up voltage is a function of load current (see Typical Operating Characteristics). This circuit is powered from the BATT pin for the MAX1722/MAX1724, guaranteeing startup at input voltages as low as 0.91V. The MAX1723 www.maximintegrated.com lacks a BATT pin; therefore, this circuit is powered through the OUT pin. Adding a Schottky diode in parallel with the P-channel synchronous rectifier allows for startup voltages as low as 1.2V for the MAX1723 (Figure 3). The external Schottky diode is not needed for input voltages greater than 1.8V. Once started, the output maintains the load as the battery voltage decreases below the startup voltage. Shutdown (MAX1723/MAX1724) The MAX1723/MAX1724 enter shutdown when the SHDN pin is driven low. During shutdown, the body diode of the P-channel MOSFET allows current to flow from the battery to the output. VOUT falls to approximately VIN - 0.6V and LX remains high impedance. Shutdown can be pulled as high as 6V, regardless of the voltage at BATT or OUT. For normal operation, connect SHDN to the input. Maxim Integrated 8 MAX1722/MAX1723/ MAX1724 1.5A IQ, Step-Up DC-DC Converters in TSOT and DFN VOUT VIN MAX1722 MAX1724 PDRV OUT P BATT DAMPING SWITCH TIMING CIRCUIT DAMP LX NDRV N GND Figure 4. Simplified Diagram of Damping Switch 1V/div 1V/div 1s/div 1s/div Figure 5. LX Ringing Without Damping Switch (MAX1723) Figure 6. LX Ringing With Damping Switch (MAX1722/MAX1724) BATT/Damping Switch (MAX1722/MAX1724) Design Procedure The MAX1722/MAX1724 include an internal damping switch (Figure 4) to minimize ringing at LX and reduce EMI. When the energy in the inductor is insufficient to supply current to the output, the capacitance and inductance at LX form a resonant circuit that causes ringing. The damping switch supplies a path to quickly dissipate this energy, suppressing the ringing at LX. This does not reduce the output ripple, but does reduce EMI with minimal impact on efficiency. Figures 5 and 6 show the LX node voltage waveform without and with the damping switch, respectively. www.maximintegrated.com Setting the Output Voltage (MAX1722/MAX1723) The output voltage can be adjusted from 2V to 5.5V using external resistors R1 and R2 (Figure 7). Since FB leakage is 20nA (max), select feedback resistor R1 in the 100k to 1M range. Calculate R2 as follows: V = R2 R1 OUT - 1 V FB where VFB = 1.235V. Maxim Integrated 9 MAX1722/MAX1723/ MAX1724 INPUT 0.8V TO VOUT 10F 1.5A IQ, Step-Up DC-DC Converters in TSOT and DFN For maximum output current, choose the inductor value so that the controller reaches the current-limit before the maximum on-time is triggered: 10H OUTPUT 2V TO 5.5V LX BATT OUT MAX1722 R2 10F L< VBATT t ON(MAX) ILIM where the maximum on-time is typically 5s, and the current limit (ILIM) is typically 500mA (see Electrical Characteristics table). FB GND R1 For larger inductor values, determine the peak inductor current (IPEAK) by: IPEAK = Figure 7. Adjustable Output Circuit VBATT t ON(MAX) L Inductor Selection The control scheme of the MAX1722/MAX1723/MAX1724 permits flexibility in choosing an inductor. A 10H inductor value performs well in most applications. Smaller inductance values typically offer smaller physical size for a given series resistance, allowing the smallest overall circuit dimensions. Circuits using larger inductance values may start up at lower battery voltages, provide higher efficiency, and exhibit less ripple, but they may reduce the maximum output current. This occurs when the inductance is sufficiently large to prevent the maximum current limit (ILIM) from being reached before the maximum ontime (tON(MAX)) expires. Table 1. Suggested Inductors and Suppliers INDUCTOR PHONE WEBSITE Coilcraft DO1608 Series DO1606 Series 847-639-2361 www.coilcraft.com Murata LQH4C Series 770-436-1300 www.murata.com Sumida CDRH4D18 Series CR32 Series CMD4D06 Series 847-545-6700 www.sumida.com CXLD140 Series +81 (06) 6355-5733 www.daidoo.co.jp 3DF Type D412F Type 847-297-0070 www.toko.com MANUFACTURER Sumitomo/ Daidoo Electronics Toko www.maximintegrated.com INPUT 0.8V TO VOUT C1 10F 10H BATT LX OUTPUT VOUT (NOM) OUT MAX1724 ON OFF C2 10F SHDN GND Figure 8. MAX1724 Standard Application Circuit The inductor's incremental saturation current rating should be greater than the peak switching current. However, it is generally acceptable to bias the inductor into saturation by as much as 20%, although this will slightly reduce efficiency. Table 1 lists suggested inductors and suppliers. Maximum Output Current The maximum output current depends on the peak inductor current, the input voltage, the output voltage, and the overall efficiency (): = I OUT(MAX) V 1 IPEAK BATT 2 V OUT Maxim Integrated 10 MAX1722/MAX1723/ MAX1724 1.5A IQ, Step-Up DC-DC Converters in TSOT and DFN Table 2. Suggested Surface-Mount Capacitors and Manufacturers (C1 and C2) MANUFACTURER AVX CAPACITOR VALUE DESCRIPTION 1F to 10F X7R Ceramic 10F to 330F TAJ Tantalum Series TPS Tantalum Series PHONE WEBSITE 843-448-9411 www.avxcorp.com 1F to 22F X5R/X7R Ceramic 10F to 330F T494 Tantalum Series 68F to 330F T520 Tantalum Series Sanyo 33F to 330F TPC Polymer Series 408-749-9714 www.secc.co.jp Taiyo Yuden 33F to 330F X5R/X7R Ceramic 800-368-2496 www.t-yuden.org 1F to 10F X7R Ceramic 847-803-6100 www.tdk.com 10F to 330F 594D Tantalum Series 595D Tantalum Series 203-452-5664 www.vishay.com Kemet TDK Vishay Sprague For most applications, the peak inductor current equals the current limit. However, for applications using large inductor values or low input voltages, the maximum ontime limits the peak inductor current (see Inductor Selection section). Capacitor Selection Choose input and output capacitors to supply the input and output peak currents with acceptable voltage ripple. The input filter capacitor (CIN) reduces peak currents drawn from the battery and improves efficiency. Low equivalent series resistance (ESR) capacitors are recommended. Ceramic capacitors have the lowest ESR, but low ESR tantalum or polymer capacitors offer a good balance between cost and performance. Output voltage ripple has two components: variations in the charge stored in the output capacitor with each LX pulse, and the voltage drop across the capacitor's ESR caused by the current into and out of the capacitor: = VRIPPLE VRIPPLE(C) + VRIPPLE(ESR) 864-963-6300 www.kemet.com where IPEAK is the peak inductor current (see Inductor Selection section). For ceramic capacitors, the output voltage ripple is typically dominated by VRIPPLE(C). For example, a 10F ceramic capacitor and a 10H inductor typically provide 75mV of output ripple when stepping up from 3.3V to 5V at 50mA. Low input-to-output voltage differences (i.e. two cells to 3.3V) require higher output capacitor values. Capacitance and ESR variation of temperature should be considered for best performance in applications with wide operating temperature ranges. Table 2 lists suggested capacitors and suppliers. PC Board Layout Considerations Careful PC board layout is important for minimizing ground bounce and noise. Keep the IC's GND pin and the ground leads of the input and output capacitors less than 0.2in (5mm) apart using a ground plane. In addition, keep all connections to FB (MAX1722/MAX1723 only) and LX as short as possible. VRIPPLE(ESR) IPEAK R ESR(COUT) ( 1 L VRIPPLE(C) I 2 -I 2 2 (VOUT -VBATT )C OUT PEAK OUT www.maximintegrated.com ) Maxim Integrated 11 MAX1722/MAX1723/ MAX1724 1.5A IQ, Step-Up DC-DC Converters in TSOT and DFN Selector Guide Package Information OUTPUT (V) SHDN LX DAMPING MAX1722EZK Adjustable No Yes MAX1723EZK Adjustable Yes No MAX1724EZK27 Fixed 2.7 Yes Yes MAX1724EZK30 Fixed 3.0 Yes Yes MAX1724EZK33 Fixed 3.3 Yes Yes MAX1724EZK50 Fixed 5.0 Yes Yes MAX1722ELT Adjustable No Yes MAX1723ELT Adjustable Yes No MAX1724ELT27 Fixed 2.7 Yes Yes MAX1724ELT30 Fixed 3.0 Yes Yes MAX1724ELT33 Fixed 3.3 Yes Yes MAX1724ELT50 Fixed 5.0 Yes Yes PART For the latest package outline information and land patterns (footprints), go to www.maximintegrated.com/packages. Note that a "+", "#", or "-" in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status. PACKAGE TYPE TSOT PACKAGE CODE Z5+1 OUTLINE NO. 21-0113 LAND PATTERN NO. 90-0241 DFN L622+1 21-0164 90-0004 Ordering Information PART TEMP RANGE MAX1722EZK+T MAX1723EZK+T MAX1724EZK27+T MAX1724EZK30+T MAX1724EZK33+T MAX1724EZK50+T MAX1722ELT+T MAX1723ELT+T MAX1724ELT27+T MAX1724ELT30+T MAX1724ELT33+T MAX1724ELT50+T -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C PINPACKAGE 5 TSOT 5 TSOT 5 TSOT 5 TSOT 5 TSOT 5 TSOT 6 DFN 6 DFN 6 DFN 6 DFN 6 DFN 6 DFN TOP MARK ADQF ADQG ADQH ADQI ADQJ ADQK ADH ADI ADJ ADK ADL ADM +Denotes a lead(Pb)-free/RoHS-compliant package. T = Tape and reel. www.maximintegrated.com Maxim Integrated 12 MAX1722/MAX1723/ MAX1724 1.5A IQ, Step-Up DC-DC Converters in TSOT and DFN Revision History REVISION NUMBER REVISION DATE PAGES CHANGED 0 7/01 Initial release 1 9/12 Added lead-free and tape-and-reel designations and added soldering temperatures 2 5/13 Corrected package and thermal information in Feature, Ordering Information, Absolute Maximum Ratings, Pin Configuration, and Package Information 3 12/15 Added 2 x 2 DFN package 4 5/16 Updated Pin Configurations diagram and Pin Description table 5 8/17 Updated Pin Configurations diagram and Ordering Information table DESCRIPTION -- 1, 2 1, 2, 11 1-3, 5, 11 6 6, 12 For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim Integrated's website at www.maximintegrated.com. Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance. Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc. (c) 2017 Maxim Integrated Products, Inc. 13 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Maxim Integrated: MAX1724EZK33+T MAX1724EZK50+T MAX1722EZK+T MAX1723EZK+T MAX1724EZK27+T MAX1724EZK30+T MAX1724EZK27-T MAX1724EZK30-T MAX1724EZK33-T MAX1724EZK50-T