SN55113, SN75113 DUAL DIFFERENTIAL LINE DRIVERS SLLS070C - SEPTEMBER 1973 - REVISED MARCH 1997 D D D D D D D D D D D 3-State Outputs High-Impedance Output State for Party-Line Applications Single-Ended or Differential AND/NAND Outputs Single 5-V Supply Dual Channel Operation Compatible With TTL Short-Circuit Protection High-Current Outputs Common and Individual Output Controls Clamp Diodes at Inputs and Outputs Easily Adaptable to SN55114 and SN75114 Applications Designed for Use With SN55115 and SN75115 description SN55113 . . . J OR W PACKAGE SN75113 . . . N PACKAGE (TOP VIEW) 1ZP 1ZS 1YS 1YP 1A 1B 1C GND 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 VCC 2ZP 2ZS 2YS 2YP 2A 2C CC SN55113 . . . FK PACKAGE (TOP VIEW) 1ZS 1ZP NC VCC 2ZP D Choice of Open-Collector, Open-Emitter, or 1YS 1YP NC 1A 1B 4 3 2 1 20 19 18 5 17 6 16 7 15 2ZS 2YS NC 2YP 2A 1C GND NC CC 2C The SN55113 and SN75113 dual differential line 14 8 drivers with 3-state outputs are designed to 9 10 11 12 13 provide all the features of the SN55114 and SN75114 line drivers with the added feature of driver output controls. Individual controls are provided for each output pair, as well as a NC - No internal connection common control for both output pairs. If any output is low, the associated output is in a high-impedance state and the output can neither drive nor load the bus. This permits many devices to be connected together on the same transmission line for party-line applications. The output stages are similar to TTL totem-pole outputs, but with the sink outputs, YS and ZS, and the corresponding active pullup terminals, YP and ZP, available on adjacent package pins. The SN55113 is characterized for operation over the full military temperature range of - 55C to 125C. The SN75113 is characterized for operation over the temperature range of 0C to 70C. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright (c) 1997, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 SN55113, SN75113 DUAL DIFFERENTIAL LINE DRIVERS SLLS070C - SEPTEMBER 1973 - REVISED MARCH 1997 FUNCTION TABLE OUTPUTS INPUTS DATA OUTPUT C CONTROL CC A B AND Y NAND Z L X X X Z Z X L X X Z Z H H L X L H H H X L L H H H H H H L H = high level, L = low level, X = irrelevant, Z = high impedance (off) B input and 4th line of function table are applicable only to driver number 1. logic symbol 1C CC 2C 1A 1B 7 logic diagram (positive logic) & 1C EN1 9 10 5 CC & EN2 & 1 1 6 1 1 2 2A 11 2 2 2 4 3 1 2 12 13 15 14 2C 1YP 1YS 1A 1ZP 1B 7 9 10 5 6 2YP 2A 2 12 15 14 2ZP 2ZS This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. Pin numbers shown are for the J, N, and W packages. POST OFFICE BOX 655303 1 1YP 1YS 1ZP 1ZS 2YP 2YS 11 2 3 13 1ZS 2YS 4 * DALLAS, TEXAS 75265 2ZP 2ZS SN55113, SN75113 DUAL DIFFERENTIAL LINE DRIVERS SLLS070C - SEPTEMBER 1973 - REVISED MARCH 1997 schematic Input 1B Input 1A 5 6 16 V CC 1 k 600 4 k V V 600 9 1 k To Other Driver 600 4 k 4 k AND 4 Pullup 1YP 900 900 AND Sink 3 Output 1YS 100 333 90 5 k 500 V 4 k Output 7 Control 1C 1.6 k 100 90 5 k 12 13 15 14 1 k 100 NAND 2 Sink Output 1ZS 500 100 Common Output 9 Control CC 10 Output Control 2C 11 Input 2A 9 1 NAND Pullup 1ZP 8 AND Pullup 2YP AND Output 2YS NAND Pullup 2ZP NAND Output 2ZS GND V ... VCC bus These components are common to both drivers. Resistor values shown are nominal and in ohms. absolute maximum ratings over operating free-air temperature range (unless otherwise noted) Supply voltage, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V Input voltage, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V Off-state voltage applied to open-collector outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 V Continuous total power dissipation (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table Operating free-air temperature range, TA: SN55113 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55C to 125C SN75113 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0C to 70C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65C to 150C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: N package . . . . . . . . . . . . . . . . . . . . . 260C Case temperature for 60 seconds: FK package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260C Lead temperature 1,6 mm (1/16 inch) from case for 60 seconds: J or W package . . . . . . . . . . . . . . . . 300C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. DISSIPATION RATING TABLE PACKAGE TA 25C POWER RATING DERATING FACTOR ABOVE TA = 25C FK 1375 mW 11.0 mW/C 880 mW 275 mW J 1375 mW 11.0 mW/C 880 mW 275 mW N 1150 mW 9.2 mW/C 736 mW N/A W 1000 mW 8.0 mW/C 640 mW 200 mW POST OFFICE BOX 655303 TA = 70C POWER RATING * DALLAS, TEXAS 75265 TA = 125C POWER RATING 3 SN55113, SN75113 DUAL DIFFERENTIAL LINE DRIVERS SLLS070C - SEPTEMBER 1973 - REVISED MARCH 1997 recommended operating conditions SN55113 Supply voltage, VCC High-level input voltage, VIH SN75113 MIN NOM MAX MIN NOM MAX 4.5 5 5.5 4.75 5 5.25 2 V 2 Low-level input voltage, VIL High-level output current, IOH Low-level output current, IOL Operating free-air temperature, TA UNIT -55 V 0.8 0.8 V - 40 - 40 mA 40 40 mA 70 C 125 0 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) VIK Input clamp voltage VCC = MIN, II = - 12 mA VOH High level output High-level voltage VCC = MIN, VIL = 0.8 V VIH = 2 V, VOL Low level output Low-level voltage VCC = MIN, IOL = 40 mA VIH = 2 V, VOK Output clamp voltage VCC = MAX, IO = - 40 mA IO(off) Off-state open-collector open collector output current VOH = 12 V VCC = MAX VOH = 5 5.25 25 V TA = 25C, IOZ SN55113 TEST CONDITIONS PARAMETER Off-state (high-impedance-state) (high impedance state) output current II Input current at maximum input voltage CC IIH High level High-level input current CC IIL Low level Low-level input current CC IOS ICC VCC = MAX, O Output controls at 0.8 V MIN MAX -0.9 -1.5 VI = 5 5.5 5V VCC = MAX MAX, VI = 2 2.4 4V VCC = MAX MAX, VI = 0 0.4 4V Short-circuit Short circuit output current VCC = MAX MAX, VO = 0 0, Supply current (both drivers) All inputs at 0 V, No load, TA = 25C TYP MAX -0.9 -1.5 2.4 3.4 2.4 3.4 IOH = - 40 mA 2 3.0 2 3.0 VIL = 0.8 V, TA = 25C UNIT V V 0 23 0.23 0.4 04 0 23 0.23 0 0.4 4 V -1.1 -1.5 -1.1 -1.5 V 1 10 1 10 TA = 125C 200 TA = 25C TA = 70C A A 20 10 10 -150 -20 VO = 0.4 V 80 20 VO = 2.4 V 80 20 VO = VCC 80 20 1 1 2 2 40 40 80 80 -1.6 -1.6 -3.2 -3.2 VO = 0 to VCC A, B, C VCC = MAX MAX, MIN IOH = -10 mA VO = 0 TA = MAX SN75113 TYP A mA A, B, C A, B, C TA = 25C 40 -40 90 -90 120 -120 VCC = MAX 47 VCC = 7 V 65 40 -40 90 -90 120 -120 65 47 65 85 65 85 A A mA mA mA All parameters with the exception of off-state open-collector output current are measured with the active pullup connected to the sink output. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions. All typical values are at T = 25C and V A CC = 5 V, with the exception of VCC at 7 V. Only one output should be shorted at a time, and duration of the short-circuit should not exceed one second. 4 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SN55113, SN75113 DUAL DIFFERENTIAL LINE DRIVERS SLLS070C - SEPTEMBER 1973 - REVISED MARCH 1997 switching characteristics, VCC = 5 V, CL = 30 pF, TA = 25C SN55113 PARAMETER TEST CONDITIONS MIN SN75113 TYP MAX 13 12 MIN UNIT TYP MAX 20 13 30 ns 20 12 30 ns tPLH Propagation delay time, low-to-high level output tPHL Propagation delay time, high-to-low-level output tPZH Output enable time to high level RL = 180 , See Figure 2 7 15 7 20 ns tPZL Output enable time to low level RL = 250 , See Figure 3 14 30 14 40 ns tPHZ Output disable time from high level RL = 180 , See Figure 2 10 20 10 30 ns tPLZ Output disable time from low level RL = 250 , See Figure 3 17 35 17 35 ns See Figure 1 PARAMETER MEASUREMENT INFORMATION 1 k 5V AND Output Input CL = 30 pF (see Note B) Pulse Generator (see Note A) NAND Output 50 CL = 30 pF (see Note B) TEST CIRCUIT 5 ns 5 ns Input 3V 90% 90% 1.5 V 1.5 V 10% 10% tPHL NAND Output 1.5 V VOH 1.5 V VOL tPLH AND Output 0V tPLH tPHL 1.5 V VOH 1.5 V VOL VOLTAGE WAVEFORMS NOTES: A. The pulse generator has the following characteristics: ZO = 50 , PRR 500 kHz, tw = 100 ns. B. CL includes probe and jig capacitance. Figure 1. Test Circuit and Voltage Waveforms tPLH and tPHL POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 5 SN55113, SN75113 DUAL DIFFERENTIAL LINE DRIVERS SLLS070C - SEPTEMBER 1973 - REVISED MARCH 1997 PARAMETER MEASUREMENT INFORMATION Input Pulse Generator (see Note A) 5V 50 AND Output CL = 30 pF (see Note B) NAND Output CL = 30 pF (see Note B) 1 k 5V TEST CIRCUIT 5 ns 5 ns Input 3V 90% 90% 1.5 V 1.5 V 10% 10% 0V tPZH VOH Output 1.5 V 0.5 V tPHZ Voff 0 V VOLTAGE WAVEFORMS NOTES: A. The pulse generator has the following characteristics: ZO = 50 , PRR 500 kHz, tw = 100 ns. B. CL includes probe and jig capacitance. Figure 2. Test Circuit and Voltage Waveforms tPZH and tPHZ 6 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 RL 180 Output SN55113, SN75113 DUAL DIFFERENTIAL LINE DRIVERS SLLS070C - SEPTEMBER 1973 - REVISED MARCH 1997 PARAMETER MEASUREMENT INFORMATION Input Pulse Generator (see Note A) 5V 50 5V 1 k CL = 30 pF (see Note B) NAND Output AND Output RL 250 Output CL = 30 pF (see Note B) TEST CIRCUIT 5 ns 5 ns 90% Input 1.5 V 3V 90% 1.5 V 10% 10% 0V tPZL tPLZ 5V Output 1.5 V 0.5 V VOL VOLTAGE WAVEFORMS NOTES: A. The pulse generator has the following characteristics: ZO = 50 , PRR 500 kHz, tw = 100 ns. B. CL includes probe and jig capacitance. Figure 3. Test Circuit and Voltage Waveforms, tPZL and tPLZ POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 7 SN55113, SN75113 DUAL DIFFERENTIAL LINE DRIVERS SLLS070C - SEPTEMBER 1973 - REVISED MARCH 1997 TYPICAL CHARACTERISTICS OUTPUT VOLTAGE vs DATA INPUT VOLTAGE OUTPUT VOLTAGE vs DATA INPUT VOLTAGE AAAA AAAA AAAA AAAA AAAA AAAA 6 6 VCC = 5 V No Load No Load TA = 25C 5 AA AA AA VO VO - Output Voltage - V VO VO - Output Voltage - V 5 VCC = 5.5 V 4 VCC = 5 V VCC = 4.5 V 3 AA AA 2 1 0 4 3 TA = 25C TA = - 55C 2 1 0 0 1 2 3 0 4 1 VI - Data Input Voltage - V 4 OUTPUT VOLTAGE vs INPUT VOLTAGE (OUTPUT CONTROL) 6 6 Load = 500 to GND TA = 25C VO VO - Output Voltage - V VCC = 5.5 V 4 VCC = 5 V VCC = 4.5 V 3 AAA AAA AA AA 2 Disabled 1 VCC = 5 V Load = 500 to GND 5 5 VO VO - Output Voltage - V 3 Figure 5 OUTPUT VOLTAGE vs INPUT VOLTAGE (OUTPUT CONTROL) High TA = 125C 4 3 TA = 25C TA = - 55C 2 High Disabled 1 0 0 0 1 2 3 4 VI - Input Voltage (Output Control) - V 0 1 2 3 4 VI - Input Voltage (Output Control) - V Figure 6 8 2 VI - Data Input Voltage - V Figure 4 TA = 125C Figure 7 Data for temperatures below 0C and above 70C and for supply voltages below 4.75 V and above 5.25 V are applicable to SN55113 circuits only. These parameters were measured with the active pullup connected to the sink output. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SN55113, SN75113 DUAL DIFFERENTIAL LINE DRIVERS SLLS070C - SEPTEMBER 1973 - REVISED MARCH 1997 TYPICAL CHARACTERISTICS OUTPUT VOLTAGE vs INPUT VOLTAGE (OUTPUT CONTROL) OUTPUT VOLTAGE vs INPUT VOLTAGE (OUTPUT CONTROL) VCC = 5.5 V VCC = 5 V 5 VO VO - Output Voltage - V VCC = 4.5 V AAAAAAA AAAAAAA AAAAAAA Load = 500 to VCC VCC = 5 V 5 4 3 AA AA AA AA 2 Disabled Low 1 AAAAAAA AAAAAAA AAAAAAA 6 Load = 500 to VCC TA = 25C VO VO - Output Voltage - V 6 4 TA = 25C 3 2 TA = 125C 1 Disabled 0 1 2 3 VI - Input Voltage (Output Control) - V 0 4 3 1 2 VI - Input Voltage (Output Control) - V HIGH-LEVEL OUTPUT VOLTAGE vs OUTPUT CURRENT OUTPUT VOLTAGE vs FREE-AIR TEMPERATURE 5 4 VCC = 4.5 V TA = 25C VO - High-Level Output Voltage - V 3.6 3.2 4 Figure 9 Figure 8 VO VO - Output Voltage - V Low 0 0 VOH(IOH = - 10 mA) 2.8 2.4 2 VOH(IOH = - 40 mA) AA AA 1.6 1.2 0.4 0 -75 -50 VCC = 5.5 V 4 VCC = 5 V 3 2 VCC = 4.5 V AA AA 0.8 VOL(IOL = 40 mA) 1 0 - 25 0 25 50 75 100 TA - Free-Air Temperature - C 125 0 - 20 -100 -40 -60 -80 IOH - Output Current - mA -120 Figure 11 Figure 10 TA = - 55C Data for temperatures below 0C and above 70C and for supply voltages below 4.75 V and above 5.25 V are applicable to SN55113 circuits only. These parameters were measured with the active pullup connected to the sink output. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 9 SN55113, SN75113 DUAL DIFFERENTIAL LINE DRIVERS SLLS070C - SEPTEMBER 1973 - REVISED MARCH 1997 TYPICAL CHARACTERISTICS SUPPLY CURRENT (BOTH DRIVERS) vs SUPPLY VOLTAGE LOW-LEVEL OUTPUT VOLTAGE vs OUTPUT CURRENT TA = 25C No Load TA = 25C 70 ICC ICC - Supply Current - mA 0.5 VOL VOL - Output Voltage - V AAAA AAAA 80 0.6 VCC = 4.5 V 0.4 0.3 VCC = 5.5 V AAA AAA 60 Inputs Grounded 50 Inputs Open 40 AA AA 0.2 0.1 30 20 10 0 0 20 40 50 80 100 0 120 0 1 2 3 4 5 6 VCC - Supply Voltage - V IOL - Output Current - mA 50 AAAAAA AAAAAA AAAAAA AAAAAA 100 VCC = 5 V Inputs Grounded No Load 90 80 ICC ICC - Supply Current - mA ICC ICC - Supply Current - mA 52 48 46 44 AAA AAA 70 60 100 AAAAAAA AAAAAAA AAAAAAA AAAAAAA AAAAAAA VCC = 5 V RL = CL = 30 pF Inputs: 3-V Square Wave TA = 25C 50 40 AA AA 42 40 30 20 10 38 36 - 75 - 50 - 25 0 25 50 75 100 125 0 0.1 0.4 TA - Free-Air Temperature - C 1 4 10 f - Frequency - MHz Figure 14 40 SUPPLY CURRENT (BOTH DRIVERS) vs SUPPLY VOLTAGE SUPPLY CURRENT (BOTH DRIVERS) vs OUTPUT CURRENT 54 8 Figure 13 Figure 12 56 7 Figure 15 Data for temperatures below 0C and above 70C and for supply voltages below 4.75 V and above 5.25 V are applicable to SN55113 circuits only. These parameters were measured with the active pullup connected to the sink output. 10 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SN55113, SN75113 DUAL DIFFERENTIAL LINE DRIVERS SLLS070C - SEPTEMBER 1973 - REVISED MARCH 1997 TYPICAL CHARACTERISTICS OUTPUT ENABLE AND DISABLE TIMES vs FREE-AIR TEMPERATURE AAAAA AAAAA AAAAA 20 18 30 VCC = 5 V CL = 30 pF See Figure 1 Output Enable and Disable Times - ns Propagation Delay Times From Data Inputs - ns PROPAGATION DELAY TIMES FROM DATA INPUTS vs FREE-AIR TEMPERATURE 16 tPLH 14 12 tPHL 10 8 6 4 2 0 - 75 - 50 - 25 0 25 50 75 100 AAAAAA AAAAAA VCC = 5 V See Figures 2 and 3 25 tPLZ 20 tPZL 15 tPHZ 10 tPZH 5 0 - 75 - 50 - 25 125 TA - Free-Air Temperature - C 25 50 75 100 125 Figure 17 Figure 16 0 TA - Free-Air Temperature - C Data for temperatures below 0C and above 70C and for supply voltages below 4.75 V and above 5.25 V are applicable to SN55113 circuits only. These parameters were measured with the active pullup connected to the sink output. APPLICATION INFORMATION Location 5 Location 3 RT RT Location 6 Location 1 Location 2 Twisted Pair Location 4 SN75113 Driver SN75115 Receiver RT = ZO. A capacitor may be connected in series with RT to reduce power dissipation. Figure 18. Basic Party-Line or Data-Bus Differential Data Transmission POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 11 PACKAGE OPTION ADDENDUM www.ti.com 25-Sep-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish (2) MSL Peak Temp Op Temp (C) Device Marking (3) (4/5) 5962-88744012A ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type -55 to 125 596288744012A SNJ55 113FK 5962-8874401EA ACTIVE CDIP J 16 1 TBD A42 N / A for Pkg Type -55 to 125 5962-8874401EA SNJ55113J 5962-8874401FA ACTIVE CFP W 16 1 TBD A42 N / A for Pkg Type -55 to 125 5962-8874401FA SNJ55113W JM38510/10405BEA ACTIVE CDIP J 16 1 TBD A42 N / A for Pkg Type -55 to 125 JM38510 /10405BEA M38510/10405BEA ACTIVE CDIP J 16 1 TBD A42 N / A for Pkg Type -55 to 125 JM38510 /10405BEA SN55113J ACTIVE CDIP J 16 1 TBD A42 N / A for Pkg Type -55 to 125 SN55113J SN75113D OBSOLETE SOIC D 16 TBD Call TI Call TI 0 to 70 SN75113DR OBSOLETE SOIC D 16 TBD Call TI Call TI 0 to 70 SN75113N ACTIVE PDIP N 16 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type 0 to 70 SN75113N SN75113NE4 ACTIVE PDIP N 16 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type 0 to 70 SN75113N SN75113NSR ACTIVE SO NS 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 0 to 70 SN75113 SN75113NSRE4 ACTIVE SO NS 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 0 to 70 SN75113 SN75113NSRG4 ACTIVE SO NS 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 0 to 70 SN75113 SNJ55113FK ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type -55 to 125 596288744012A SNJ55 113FK SNJ55113J ACTIVE CDIP J 16 1 TBD A42 N / A for Pkg Type -55 to 125 5962-8874401EA SNJ55113J SNJ55113W ACTIVE CFP W 16 1 TBD A42 N / A for Pkg Type -55 to 125 5962-8874401FA SNJ55113W Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 25-Sep-2013 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF SN55113, SN75113 : * Catalog: SN75113 * Military: SN55113 NOTE: Qualified Version Definitions: Addendum-Page 2 PACKAGE OPTION ADDENDUM www.ti.com 25-Sep-2013 * Catalog - TI's standard catalog product * Military - QML certified for Military and Defense Applications Addendum-Page 3 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device SN75113NSR Package Package Pins Type Drawing SO NS 16 SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 2000 330.0 16.4 Pack Materials-Page 1 8.2 B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 10.5 2.5 12.0 16.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) SN75113NSR SO NS 16 2000 367.0 367.0 38.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2013, Texas Instruments Incorporated