B-13/15-155C-F-SSC3-G5 - Source Photonics, Inc.

- 1 -

P/N: B-1x/1x-155(C)-F-SSC3x(-G5)

155 Mbps Bi-directional Receptacle Single Fiber Transceiver

DS-5750 Rev 0.0 2009-09-04

Features

z Diplexer Single Mode Single Fiber 2x5 SFF SC

Receptacle connector

z Wavelength Tx 1310 nm/Rx 1530 nm

(B-13/15-155(C)-F-SSC3x)

z Wavelength Tx 1530 nm/Rx 1310 nm

(B-15/13-155(C)-F-SSC3x)

z SONET OC-3 SDH STM-1 Compliant

z Single +3.3V Power Supply

z LVPECL Differential Inputs and Outputs

(B-1x/1x-155-F-SSC3x)

z LVTTL Differential Inputs and Outputs

(B-1x/1x-155C-F-SSC3x)

z Wave Solderable and Aqueous Was hable

z Class 1 Laser Int. Safety Standard IEC-825 Compliant

z Uncooled Laser diode with MQW structure

z Complies with Telcordia (Bellco re) GR-468-CORE

z EMI Shielding Finger Optional

z RoHS compliance available

Table 1 – Absolute Maximum Rating

Parameter Symbol Min. Typical Max. Unit Notes

Power Supply Voltage Vcc 0 - 3.6 V

Output Current Iout - - 30 mA

Soldering Temperature - - - 260 ºC 1

Storage Temperature Tstg 0 - 70 ºC 2

Storage Temperature Tstg -40 - 85 ºC 3

Note 1: 10 senconds on leads only

Note 2: B-1x/1x-155(C)-F-SSC3(S)

Note 3: B-1x/1x-155(C)-F-SSC3A(S)

Table 2 – Recommended Operating Condition

Parameter Symbol Min. Typical Max. Unit Notes

Power Supply Voltage Vcc 3.1 3.3 3.5 V 4

Operating Temperature (Case) Topr 0 - 70 ºC

Data Rate DR - 155 - Mbps

Note 4: please refer to ordering information

- 2 -

P/N: B-1x/1x-155(C)-F-SSC3x(-G5)

155 Mbps Bi-directional Receptacle Single Fiber Transceiver

DS-5750 Rev 0.0 2009-09-04

Table 3 – Transmitter Specification s (Optical)

Parameter Symbol Min. Typical Max. Unit Notes

Optical Transmit Power Po -14 - -8 dBm 5

Output Center Wavelength λc 1260 1310 1360 nm 6

Output Center Wavelength λc 1480 1530 1580 nm 7

Output Spectrum Width Δλ - - 3 nm 8

Extinction Ratio ER 8.2 - - dB

Output Eye Compliant with ITU-T recommendation G.957/STM-1

Optical Rise/Fall Time tr /tf - - 2 ns 9

Optical Isolation - 30 - - dB 10

Relative Intensity Noise RIN - - -116 dB/Hz

Total Jitter TJ - - 1.0 ns 11

Note 5: Output power is coupled into a 9/125 µm single mode fiber

Note 6: B-13/15-155(C)-F-SSC3x

Note 7: B-15/13-155(C)-F-SSC3x

Note 8: RMS (σ)

Note 9: 10% to 90% Values

Note 10: Tx: 1310 nm/ Rx: 1550 nm

Note 11: Measured with 223-1 PRBS with 72 ones and 72 zeros.

Table 4 – Transmitter Specification s (Electrical)

Parameter Symbol Min. Typical Max. Unit Notes

Power Supply Current ICC - - 140 mA 12

Data Input Current-Low IIL -350 - - μA

Data Input Current-High IIH - - 350

μA

Differential Input Voltage VIH-VIL 300 - - mV

Data Input Voltage-Low VIL-VCC -2.0 - -1.58 mV

Data Input Voltage-High VIH-VCC -1.1 - -0.74 mV 13

Note 12: Maximum current is specified at Vcc=Maximum @ maximum temperature

Note 13: These inputs are compatible with 10K, 10KH and 100K ECL and PECL inputs

- 3 -

P/N: B-1x/1x-155(C)-F-SSC3x(-G5)

155 Mbps Bi-directional Receptacle Single Fiber Transceiver

DS-5750 Rev 0.0 2009-09-04

Table 5 – Receiver Specifications (Optical)

Parameter Symbol Min. Typical Max. Unit Notes

Sensitivity - - - -33 dBm 14

Maximum Input Power Pin -3 - - dBm

Signal Detect-Asserted Pa - - -33 dBm 15

Signal Detect-Deasserted Pd -45 - - dBm 16

Signal Detect-Hysteresis - 1.0 - 4.0 dB

Cross Talk - - - -33 dB

Wavelength of Operation 1480 - 1600 nm 17

Wavelength of Operation 1260 - 1360 nm 18

Note 14: Measured with 223-1 PRBS, BER = 10-10.

Note 15: Measured on transition: low to high, The SD level should be deasserted when fiber disconnected

Note 16: The SD level should be deasserted when fiber is disconnected

Note 17: B-13/15-155(C)-F-SSC3x

Note 18: B-15/13-155(C)-F-SSC3x

Table 6 – Receiver Specifications (Electrical)

Parameter Symbol Min. Typical Max. Unit Notes

Power Supply Current ICC - - 100 mA

Data Output Voltage-Low VOL-VCC -2.0 - -1.58 V

Data Output Voltage-High VOH-VCC -1.1 - -0.74 V 20

Signal Detect Output Voltage-Low VSDL-VCC -2.0 - -1.58 V

Signal Detect Output Voltage-High VSDH-VCC -1.1 - -0.74 V

Signal Detect Output Voltage-Low VSDL-VCC - - 0.5 V

Signal Detect Output Voltage-High VSDH-VCC 2.0 - - V

Note 19: The current excludes the output load current

Note 20: These outputs are compatible with 10K, 10KH and 100KECL and LVPECL outputs.

Note 21: LVPECL, B-1x/1x-155-F-SLC3x

Note 22: LVPECL, B-1x/1x-155C-F-SLC3x

- 4 -

P/N: B-1x/1x-155(C)-F-SSC3x(-G5)

155 Mbps Bi-directional Receptacle Single Fiber Transceiver

DS-5750 Rev 0.0 2009-09-04

Connection Diagram

Table 7 – Pin Definitions

Pin Unit Notes

1 RxGND

Directly connect this pin to the receiver ground plane

2 RxVcc

+3.3V dc power for the receiver section

3 SD

Active high on this indicates a received optical signal(LVPECL/LVTTL)

4 RD-

Receiver Data Out Bar(LVPECL)

5 RD+

Receiver Data Out (LVPECL)

6 TxVcc

+3.3V dc power for the transmitter section

7 TxGND

Directly connect this pin to the tranmitter ground plane

8 TxDIS

Transmitter disable(LVTTL)

9 TD+

Transmitter Data In (LVPECL)

10 TD-

Transmitter Data In Bar (LVPECL)

- 5 -

P/N: B-1x/1x-155(C)-F-SSC3x(-G5)

155 Mbps Bi-directional Receptacle Single Fiber Transceiver

DS-5750 Rev 0.0 2009-09-04

Recommended Circuit Schematic

B-1x/1x-155-F-SSC3x(-G5)

TERMINATE AT

TRANSCEIVER INPUTS Z=50Ω

Z=50Ω

100Ω

TD-

TD+

130Ω

82Ω

Vcc(+3.3V)

100Ω

RD+

RD-

Z=50Ω

130Ω130Ω

Vcc(+3.3V)

PHY DEVICE

LVPECL

10μF

C3C2

1μH

67810 9

12 3 4 5

1μH

TERMINATE AT

DEVICE INPUTS

NOTE:C1=C2=C3=100nF

RxGND

RxVcc

RD-

RD+ TxVcc

TxGND

TD+

TD-

TxDIS

Vcc(+3.3V)

130Ω

LVTTL

Tx Disable

LVPECL

The split-loaded terminations for ECL signals need to be located at the input of devices receiving those ECL signals.

The power supply filtering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module Rx Vcc.

A GND plane under the module is required for good EMI and sensitivity performance.

- 6 -

P/N: B-1x/1x-155(C)-F-SSC3x(-G5)

155 Mbps Bi-directional Receptacle Single Fiber Transceiver

DS-5750 Rev 0.0 2009-09-04

Recommended Circuit Schematic

B-1x/1x-155C-F-SSC3x(-G5)

TERMINATE AT

TRANSCEIVER INPUTS Z=50Ω

Z=50Ω

100Ω

TD-

TD+

130Ω

Vcc(+3.3V)

100Ω

RD+

RD-

Z=50Ω

Vcc(+3.3V)

PHY DEVICE

LVPECL

10μF

C3C2

1μH

67810 9

12 3 4 5

1μH

TERMINATE AT

DEVICE INPUTS

NOTE:C1=C2=C3=100nF

RxGND

RxVcc

RD-

RD+ TxVcc

TxGND

TD+

TD-

TxDIS

Vcc(+3.3V)

130Ω

LVTTL

Tx Disable

LVTTL

The split-loaded terminations for ECL signals need to be located at the input of devices receiving those ECL signals.

The power supply filtering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module Rx Vcc.

A GND plane under the module is required for good EMI and sensitivity performance.

- 7 -

P/N: B-1x/1x-155(C)-F-SSC3x(-G5)

155 Mbps Bi-directional Receptacle Single Fiber Transceiver

DS-5750 Rev 0.0 2009-09-04

Recommended Board Layout Hole Pattern

DIMENSION IN MILLIMETER (INCHES)

NOTES:

3.THE MOUNTING STUDS SHOULD BE SOLDERED TO CHASSIS GROUND FOR MECHANICAL INTEGRITY.

TRACES OR GROUND CONNECTION IN KEEP-OUT AREAS.

2.THE HATCHED AREAS ARE KEEP-OUT AREAS RESERVED FOR HOUSING STANDOFF. NO METAL

1.THIS FIGURE DESCRIBE THE RECOMMAND CIRCUIT BOARD LAYOUT FOR THE SFF TRANSCEIVER.

- 8 -

P/N: B-1x/1x-155(C)-F-SSC3x(-G5)

155 Mbps Bi-directional Receptacle Single Fiber Transceiver

DS-5750 Rev 0.0 2009-09-04

Package Diagram

B-1x/1x-155(C)-F-SSC3(A)

PIN 6

PIN 5

Stud Stand-off PIN 10

Housing Lead

PIN 1

Stand-off

Housing Lead

Unit s: mm

- 9 -

P/N: B-1x/1x-155(C)-F-SSC3x(-G5)

155 Mbps Bi-directional Receptacle Single Fiber Transceiver

DS-5750 Rev 0.0 2009-09-04

Package Diagram

B-1x/1x-155(C)-F-SSC3S

B-1x/1x-155(C)-F-SSC3AS

Housing Lead

Stud PIN 10

Housing Lead

PIN 6 Stand-off

PIN 1

Matel Finger

Stand-off

PIN 5

Unit s: mm

- 10 -

P/N: B-1x/1x-155(C)-F-SSC3x(-G5)

155 Mbps Bi-directional Receptacle Single Fiber Transceiver

DS-5750 Rev 0.0 2009-09-04

Order Information

Table 8 – Order Information

Part No. Part No.

B-13/15-155-F-SSC3 B-13/15-155C-F-SSC3

B-15/13-155-F-SSC3 B-15/13-155C-F-SSC3

B-13/15-155-F-SSC3A B-13/15-155C-F-SSC3A

B-15/13-155-F-SSC3A B-15/13-155C-F-SSC3A

B-13/15-155-F-SSC3S B-13/15-155C-F-SSC3S

B-15/13-155-F-SSC3S B-15/13-155C-F-SSC3S

B-13/15-155-F-SSC3AS B-13/15-155C-F-SSC3AS

B-15/13-155-F-SSC3AS B-15/13-155C-F-SSC3AS

B-13/15-155-F-SSC3-G5 B-13/15-155C-F-SSC3-G5

B-15/13-155-F-SSC3-G5 B-15/13-155C-F-SSC3-G5

B-13/15-155-F-SSC3A-G5 B-13/15-155C-F-SSC3A-G5

B-15/13-155-F-SSC3A-G5 B-15/13-155C-F-SSC3A-G5

B-13/15-155-F-SSC3S-G5 B-13/15-155C-F-SSC3S-G5

B-15/13-155-F-SSC3S-G5 B-15/13-155C-F-SSC3S-G5

B-13/15-155-F-SSC3AS-G5 B-13/15-155C-F-SSC3AS-G5

B-15/13-155-F-SSC3AS-G5 B-15/13-155C-F-SSC3AS-G5

- 11 -

P/N: B-1x/1x-155(C)-F-SSC3x(-G5)

155 Mbps Bi-directional Receptacle Single Fiber Transceiver

DS-5750 Rev 0.0 2009-09-04

Part Numbering Definition:

B - 1x/1x - 155(C) - F - S SC 3 Operating Temperature Shielding Finger -RoHS

● Wavelength :

13/15 =

Tx Wavelength = 1310nm

Rx Wavelength = 1530nm

15/13 =

Tx Wavelength = 1530nm

Rx Wavelength = 1310nm

● Communication Protocol

(155Mbps)

● +3.3V SFF Transceiver

● Single mode fiber

● Connector options

● Intermediate Reach

● Operating Temperature

Blank = Commercial temper ature (0 to 70oC)

A = Commercial temperatur e (-40 to 85oC)

● Shielding Finger Option

Blank = No shielding finger

S = with Shielding finger

● RoHS compliance available

G5 = RoHS 5/6-compl iant product (lead exemption)

- 12 -

P/N: B-1x/1x-155(C)-F-SSC3x(-G5)

155 Mbps Bi-directional Receptacle Single Fiber Transceiver

DS-5750 Rev 0.0 2009-09-04

Warnings

Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static

free environment is highly recommended. Follow guidelines according to proper ESD procedures.

Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or

indirect radiation.

Legal Notice

IMPORTANT NOTICE !

All information contained in this document is subject to change without notice, at Source Photonics’ sole and

absolute discretion. Source Photonics warrants performance of its products to current specifications only in

accordance with the company’s standard one-year warranty; however, specifications designated as “preliminary”

are given to describe components only, and Source Photonics expressly disclaims any and all warranties for said

products, including express, implied, and statutory warranties, warranties of merchantability, fitness for a particular

purpose, and non-infringement of proprietary rights. Please refer to the company’s Terms and Conditions of Sale for

further warranty information.

Source Photonics assumes no liability for applications assistance, customer product design, software performance,

or infringement of patents, services, or intellectual property described herein. No license, either express or implied,

is granted under any patent right, copyright, or intellectual property right, and Source Photonics makes no

representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual

property rights. Products described in this document are NOT intended for use in implantation or other life support

applications where malfunction may result in injury or death to persons. Source Photonics customers using or

selling products for use in such applications do so at their own risk and agree to fully defend and indemnify Source

Photonics for any damages resulting from such use or sale.

THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN “AS IS” BASIS. Customer agrees

that Source Photonics is not liable for any actual, consequential, exemplary, or other damages arising directly or

indirectly from any use of the information contained in this document. Customer must contact Source Photonics to

obtain the latest version of this publication to verify, before placing any order, that the information contained herein is

current.

Contact

U.S.A. Headquarters

20550 Nordhoff Street

Chatsworth, CA 91311

USA

Tel: +1-818-773-9044

Fax: +1-818-773-0261

sales@sourcephotonics.com

China

Building #2&5, West Export Processing Zone

No. 8 Kexin Road, Hi-Tech Zone

Chengdu, 611731, China

Tel: +86-28-8795-8788

Fax: +86-28-8795-8789

sales@sourcephotonics.com.cn

Taiwan

9F, No 81, Shui Lee Rd.

Hsinchu, 300, Taiwan

R.O.C.

Tel: +886-3-5169222

Fax: +886-3-5169213

sales@sourcephotonics.com.tw