Power-over-Ethernet
PALS AC-DC Series Data Sheet
JUL 06, 2006 revised to SEP 19, 2006 Page 1 of 5 www.power-one.com
Features
RoHS lead free solder and lead solder exempted
products are available
Single-phase AC input
Up to 9 W/in3 power density
1U or 3U height configurations
Power Factor Correction (PFC) Meets EN61000-3-2
Current share with ORing diodes
Overtemperature, overload, and overvoltage
protection
Power supply status indicators
•I
2C protocol alarms, status, & control
Standby voltage - 12 VDC @ 500 mA with
ORing diode
Enable signal for each output
Model Selection
MODEL TOTAL OUTPUT OUTPUT MAXIMUM OUTPUT LINE LOAD RIPPLE & NOISE INITIAL SETTING
POWER (WATTS) VOLTAGE CURRENT REGULATION REGULATION 1mVp-p 2ACCURACY
PALS400-2482 400 48V 8A 0.1% 0.2% 120 0.2%
12V 16A 0.1% 0.2% 120 0.2%
PALS600-2482 600 48V 9A 0.1% 0.2% 120 0.2%
12V 16A 0.1% 0.2% 120 0.2%
NOTES:
1With Remote Sense connected.
2Maximum peak-to-peak noise expressed as a percentage of output voltage, 20 MHz bandwidth.
Input Specifications
PARAMETER CONDITIONS/DESCRIPTION MIN NOM MAX UNITS
Input Voltage - AC Single-phase continuous input range. 85 264 VAC
Input Frequency AC input. 47 63 Hz
Hold-up Time After last AC line peak at full power. At 115 VAC. 20 ms
Input Current At full rated load. At 85 VAC. PALS400: 6.5 Arms
At 85 VAC. PALS600: 10
Inrush Surge Current Internally limited by thermistor. Vin = 115VAC (one cycle). 25° C. 17 Apk
Power Factor Per EN61000-3-2 0.98 W/VA
Operating Frequencies Boost frequency 95 kHz
Forward converter frequency 125
The PALS Series consists of 400 and 600 watt ac-dc power supplies designed specifically for use in power-over-
ethernet applications. The supplies have dual outputs of 48 and 12 volts which provide LAN port and internal system
power. A 500 mA standby output facilitates I2C interface operations. The units are fully-enclosed, have 1500 VAC
(2250 VDC) output isolation, and comply to IEEE802.3AF.
The PALS Series provides excellent protection against input voltage transients. Supply outputs are fully floating,
meaning that users can use them for either positive or negative polarity needs.
Output voltage terminals and interface access is through a hot-swap connector at the rear of the supply. The AC input
fans, handle, and LED indicator lights are located on the front panel of the supply. Airflow is from the front through the
rear. Alarm, monitoring, and control signals are floating from the rear output and can be referenced.
The PALS Series meets international safety requirements and is CE Marked to the Low Voltage Directive.
Power-over-Ethernet
PALS AC-DC Series Data Sheet
JUL 06, 2006 revised to SEP 19, 2006 Page 2 of 5 www.power-one.com
Output Specifications
PARAMETER CONDITIONS/DESCRIPTION MIN NOM MAX UNITS
Efficiency Full rated load. 82 85 %
Minimum Loads Minimum loading required to maintain regulation. 0 A
Output Power (Does not include standby output power) PALS400: 400 Watts
PALS600: 600
Overshoot / Undershoot Output voltage overshoot/undershoot at turn-on. 3 %
Transient Response Maximum recovery time, to within 1% of initial set point due to a 400 µs
50% load change, 1A/µs, 2% max. deviation.
Turn-On Delay Time required for initial output voltage stabilization. 1 Sec
Turn-on Rise Time Time required for output voltage to rise from 10% to 90%. 100 ms
Interface Signals and Internal Protection
PARAMETER CONDITIONS/DESCRIPTION MIN NOM MAX UNITS
Overvoltage Protection Latch style overvoltage protection. Vo1 55.2 60.0 V
Vo2 13.8 15.0
Overcurrent Protection Straight line current limit, as a percentage of maximum rated load. 110 120 %
Short Circuit Protection Enabled during overcurrent conditions. 25 %
Overtemperature/ Time to shutdown due to excessive internal temperature or fan failure. TBD ms
Fan Failure Warning Latching shutdown. (Note 1)
Output Good TTL open collector signal. Percent of output voltage when V1 output is 3 5 %
within nominal range. Signal high indicates out of tolerance output.
(Note 1)
Input Power Fail Warning TTL open collector signal. Time before VOUT drops to 95% due to loss of input power. 5 ms
(Note 1)
Power Supply Present Signal Resistance of connection to logic ground to allow user to determine if 100 Ohms
power supply is present. (Note 1)
Current Share Active current share on Vo1 & Vo2 for load current >10% of full load share within: 5 %
Remote Sense Total voltage compensation for cable losses with respect to the main output. 1.0 V
Enable TTL compatible logic signal. Logic “low” required to enable each output. 2 mA
(Note 1)
Auxiliary Power Rated current of isolated 12 VDC power source. 500 mA
I2C Bus Management Interface
STATICIncludes static information such as: part number and revision level, output rating, serial number, date code, and manufacturing location.
STATUS (Logic 1 or 0)
Power Supply OK
AC Input OK
DC Output OK
Power Supply Seated
Overtemperature.
CONTROL SIGNAL
Inhibit
Safety, Regulatory, and EMI Specifications
PARAMETER CONDITIONS/DESCRIPTION MIN NOM MAX UNITS
Agency Approvals UL60950-1/CSA 22.2 No. 60950-1, EN60950-1 (TUV), and IEC60950-1.
Electromagnetic Interference FCC CFR title 47 Part 15 Sub-Part B - Conducted. B
EN55022 / CISPR 22 Conducted. B Class
ESD Susceptibility Per EN61000-4-2, level 4. 8 kV
Radiated Susceptibility Per EN61000-4-3, level 3. 10 V/M
EFT/Burst Per EN61000-4-4, level 4. ±4 kV
Surge Per EN61000-4-5, level 3. Line-to-Line 1 kV
Line-to-Ground 2
Leakage Current Per EN60950. at 265 VAC, 60 Hz 2.6 mA
NOTE: 1) Also available on I2C data line.
Power-over-Ethernet
PALS AC-DC Series Data Sheet
JUL 06, 2006 revised to SEP 19, 2006 Page 3 of 5 www.power-one.com
Environmental Specifications
PARAMETER CONDITIONS/DESCRIPTION MIN NOM MAX UNITS
Altitude Operating. 10k ASL Ft.
Non-Operating. 40k ASL Ft.
Operating Temperature At 100% load: 0 50 °C
At 50% load: 70 °C
Storage Temperature -40 85 °C
Temperature Coefficient 0 °C to 70 °C (after 15-minute warm-up). .02 %/°C
Relative Humidity Non-Condensing. 95 %RH
Shock Operating: half-sine 10ms, 3 axis +20 GPK
Non-operating: half-sine 10ms, 3 axis +40
Vibration Operating: swept sine 5-2000-5 Hz, 5-32 Hz, 0.02îDA, 32-2000 Hz 1 GPK
Non-operating: random 10-2000 Hz 6.15 Grms
DC OK
AC OK
O.T.P
40.1 (1.58")
40.4 (1.59")
30.1
20.05
POWERLED AC Inl
116.6
33.0 22.0 19.5
10.0 17.5
19.0
20.0
109.22 (4.3")
Fastener Screw:
Features required for mounting...
SOUTHCO 52-19-11-4
THREAD SIZE #4-40
OR EQU TYPE
PALS Front Panel View
PALS Rear Connector Panel View
Output Connector
AMP 2-1450130-9(2P+24S+2P)
FCI 51730-016(2P+24S+2P)
or EQU TYPE
48.26
Mates with:
FCI 51740-10202402AA
or equivalent.
26.67
50.8
13.76
Ordering Information:
OPTIONS SUFFIXES TO ADD TO PART NUMBER
RoHS lead solder exemption No RoHS character required.
RoHS compliant for all 6 substances Add “G” as the last character of the part number.
Power-over-Ethernet
PALS AC-DC Series Data Sheet
JUL 06, 2006 revised to SEP 19, 2006 Page 4 of 5 www.power-one.com
PALS Right Side View
#4-40-3PL
Mounting Holes
Marked "B"
102.0
BOTTOM
115.0
30.0
22.0
BBB
*References to the center of guide pin on blind mate connector.
PSUP N/COTFA2A1
Vo2CS
Vo2-S
RTN
1N
1S
1K
P2
1J
P1
Vo2+S
Vo2 Vo2
N/C
N/C
N/CVaux
OGOOD
PF
Vo1 ENA
VauxRTN
Vo2 ENA
A0
SCL
SDA
4N 5N
5S4S
3N2N
2S 3S
4K 5K3K2K
2J 4J 5J3J
N/C
Vo1+S
Vo1-S
Vo1CS
Vo1
RTN
Vo1
6N
6S
6K
6J
P4P3
P4
P1
K
J
N
S534261
P3
P2
Output Connector Pin Assignments
Power-over-Ethernet
PALS AC-DC Series Data Sheet
JUL 06, 2006 revised to SEP 19, 2006 Page 5 of 5 www.power-one.com
101.6 (4.0")
25.0 (0.98") 264.2 (10.4")
FAN
17.0
V.R. holes
10.3
RATING LABEL
72.5
PALS Bottom View
#4-40-4PL
Mounting Holes
Marked "A"
75.0
246.0
73.6
FAN
SPRING CLIP
22.0
8.0
264.2
250.0
12.0
13.3
A
AA
A
PALS Top View
NUCLEAR AND MEDICALAPPLICATIONS - Power-One products are not designed, intended for use in, or authorized for use as critical components
in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written consent of the respective
divisional president of Power-One, Inc.
TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on the
date manufactured. Specifications are subject to change without notice.