(Notice)
•In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment
using any SHARP devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before
using any SHARP device.
•Specifications are subject to change without notice for improvement.
(Internet)
•Data for Sharp's optoelectronic/power devices is provided on internet. (Address http://sharp-world.com/ecg/)
D4-000901-A
Features
Applications
Absolute Maximum Ratings
Outline Dimensions
Under development
New product
(Unit: mm)
Internal connection diagram
4
1
3
2
Cathode
Cathode
Cathode
Anode
5
8
6
T2
G
T1
1234
56
8
2.54±0.25
6.5±0.5
1.2±0.3
9.66±0.5
3.5±0.5
7.62±0.3
3.25±0.5
0.5±0.1
0.5TYP.
0.26±0.1
Anode mark
Solid State Relay
Small Current Solid State Relay
(1) 8-pin DIP package
(2) Low minimum trigger current (IFT[MAX.]=5mA)
(3) Isolation voltage Viso(rms): 4.0kV
(1) Various types of home appliances
Model Line-up
* Surface mount type, taped products are optionally available.
RMS ON
-state
current (rms)
0.6 A
0.9 A
For a 100V line For a 200V line
PR26MF12NSZ PR36MF12NSZ
PR39MF12NSZPR29MF12NSZ
1234
568
(Ta=25˚C)
Input
Output *1
*2
*3
*1 50Hz sine wave
*2 AC for 1 minute, RH = 40 to 60%, f=60Hz
*3 For 10 s
Parameter
Forward current
Reverse voltage
RMS ON-state current
Peak one cycle surge current
Repetitive peak OFF-state voltage
Isolation voltage
Operating temperature
Storage temperature
Soldering temperature
Symbol
IF
VR
IT(rms)
Isurge
VDRM
Viso(rms)
Topr
Tstg
Tsol
Ratings
50
6
0.6
0.9
6
9
400
600
4
–25 to +85
–40 to +125
260
Unit
mA
V
A
A
V
kV
˚C
˚C
˚C
PR26MF12NSZ
PR36MF12NSZ
PR36MF12NSZ
PR39MF12NSZ
PR26MF12NSZ
PR29MF12NSZ
PR29MF12NSZ
PR39MF12NSZ
PR26MF12NSZ
PR36MF12NSZ
PR29MF12NSZ
PR39MF12NSZ
PR26MF12series
1/2
S mark Model No.
D4-000901-A
As of January 2001
Solid State Relay
Electro-optical Characteristics (Ta=25˚C)
MIN.
-
-
-
-
-
100
-
5×1010
-
Input
Output
Transfer
characteristics
Parameter
Forward voltage
Reverse current
Repetitive peak OFF-state current
ON-state voltage
Holding current
Critical rate of rise of OFF-state voltage
Minimum trigger current
Isolation resistance
Turn-on time
Symbol
VF
IR
IDRM
VT
IH
dv/dt
IFT
RISO
ton
Conditions
IF=20mA
VR=3V
VD=VDRM
IT=0.6A
IT=0.9A
VD=6V
VD=(1 / √2 ) · VDRM
VD=6V, RL=100Ω
DC500V, 40 to 60%RH
VD=6V, RL=100Ω
IF=10mA
Unit
V
µA
µA
V
mA
V/µs
mA
Ω
µs
0
0.6
0.4
0.8
1.0
0.2
-20-25 020 40 60 80 100
0
0.6
0.4
0.8
1.0
0.2
-20-25 020 40 60 80 100
RMS ON-state current IT(rms) (A)
RMS ON-state current IT(rms) (A)
PR26MF12NSZ, PR36MF12NSZ PR29MF12NSZ, PR39MF12NSZ
Fig. 1-2 RMS ON-state Current vs. Ambient
Temperature
Fig. 1-1 RMS ON-state Current vs. Ambient
Temperature
Ambient temperature Ta(˚C) Ambient temperature Ta(˚C)
PR26MF12series
TYP.
1.2
-
-
-
-
-
-
1×1011
-
MAX.
1.4
10
100
3.0
25
-
5
-
100
PR26MF12NSZ
PR36MF12NSZ
PR29MF12NSZ
PR39MF12NSZ
2/2
NOTICE
●The circuit application examples in this publication are provided to explain representative applications of SHARP
devices and are not intended to guarantee any circuit design or license any intellectual property rights. SHARP takes
no responsibility for any problems related to any intellectual property right of a third party resulting from the use of
SHARP's devices.
●Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. SHARP
reserves the right to make changes in the specifications, characteristics, data, materials, structure, and other contents
described herein at any time without notice in order to improve design or reliability. Manufacturing locations are
also subject to change without notice.
●Observe the following points when using any devices in this publication. SHARP takes no responsibility for damage
caused by improper use of the devices which does not meet the conditions and absolute maximum ratings to be used
specified in the relevant specification sheet nor meet the following conditions:
(i) The devices in this publication are designed for use in general electronic equipment designs such as:
--- Personal computers
--- Office automation equipment
--- Telecommunication equipment [terminal]
--- Test and measurement equipment
--- Industrial control
--- Audio visual equipment
--- Consumer electronics
(ii) Measures such as fail-safe function and redundant design should be taken to ensure reliability and safety when
SHARP devices are used for or in connection with equipment that requires higher reliability such as:
--- Transportation control and safety equipment (i.e., aircraft, trains, automobiles, etc.)
--- Traffic signals
--- Gas leakage sensor breakers
--- Alarm equipment
--- Various safety devices, etc.
(iii)SHARP devices shall not be used for or in connection with equipment that requires an extremely high level of
reliability and safety such as:
--- Space applications
--- Telecommunication equipment [trunk lines]
--- Nuclear power control equipment
--- Medical and other life support equipment (e.g., scuba).
●Contact a SHARP representative in advance when intending to use SHARP devices for any "specific" applications
other than those recommended by SHARP or when it is unclear which category mentioned above controls the
intended use.
●If the SHARP devices listed in this publication fall within the scope of strategic products described in the Foreign
Exchange and Foreign Trade Control Law of Japan, it is necessary to obtain approval to export such SHARP devices.
●This publication is the proprietary product of SHARP and is copyrighted, with all rights reserved. Under the copyright
laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical, for any purpose, in whole or in part, without the express written permission of SHARP. Express written
permission is also required before any use of this publication may be made by a third party.
●Contact and consult with a SHARP representative if there are any questions about the contents of this publication.
