PD - 97550 AUIRFP2907Z AUTOMOTIVE GRADE HEXFET(R) Power MOSFET Features D Advanced Process Technology Ultra Low On-Resistance 175C Operating Temperature Fast Switching Repetitive Avalanche Allowed up to Tjmax Lead-Free, RoHS Compliant Automotive Qualified * V(BR)DSS 75V RDS(on) max. G S 4.5m ID 170A D Description Specifically designed for Automotive applications, this HEXFET(R) Power MOSFET utilizes the latest processing techniques to achieve extremely low onresistance per silicon area. Additional features of this design are a 175C junction operating temperature, fast switching speed and improved repetitive avalanche rating . These features combine to make this design an extremely efficient and reliable device for use in Automotive applications and a wide variety of other applications. G D S TO-247AC G D S Gate Drain Source Absolute Maximum Ratings Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only; and functional operation of the device at these or any other condition beyond those indicated in the specifications is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. The thermal resistance and power dissipation ratings are measured under board mounted and still air conditions. Ambient temperature (T A) is 25C, unless otherwise specified. Parameter ID @ TC = 25C Continuous Drain Current, VGS @ 10V ID @ TC = 100C Continuous Drain Current, VGS @ 10V c EAS (tested) IAR EAR TJ TSTG Single Pulse Avalanche Energy (Thermally Limited) Single Pulse Avalanche Energy Tested Value i Avalanche Current c Repetitive Avalanche Energy h A 680 Linear Derating Factor Gate-to-Source Voltage Units 170 120 IDM Pulsed Drain Current PD @TC = 25C Maximum Power Dissipation VGS EAS Max. d Operating Junction and 310 W 2.0 20 W/C V 520 mJ 690 See Fig.12a,12b,15,16 A mJ C -55 to + 175 Storage Temperature Range Soldering Temperature, for 10 seconds (1.6mm from case ) Mounting torque, 6-32 or M3 screw Thermal Resistance Typ. Max. Units --- 0.49 C/W Case-to-Sink, Flat, Greased Surface 0.24 --- Junction-to-Ambient --- 40 RJC Junction-to-Case RCS RJA j Parameter 300 10 lbf*in (1.1N*m) HEXFET(R) is a registered trademark of International Rectifier. *Qualification standards can be found at http://www.irf.com/ www.irf.com 1 08/13/2010 AUIRFP2907Z Static Electrical Characteristics @ TJ = 25C (unless otherwise specified) Parameter V(BR)DSS VDSS/TJ RDS(on) VGS(th) gfs IDSS IGSS Drain-to-Source Breakdown Voltage Breakdown Voltage Temp. Coefficient Static Drain-to-Source On-Resistance Gate Threshold Voltage Forward Transconductance Drain-to-Source Leakage Current Gate-to-Source Forward Leakage Gate-to-Source Reverse Leakage Min. Typ. Max. Units 75 --- --- 2.0 180 --- --- --- --- --- 0.069 3.5 --- --- --- --- --- --- --- --- 4.5 4.0 --- 20 250 200 -200 Conditions V VGS = 0V, ID = 250A V/C Reference to 25C, ID = 1mA m VGS = 10V, ID = 90A V VDS = VGS, ID = 250A S VDS = 25V, ID = 90A A VDS = 75V, VGS = 0V VDS = 75V, VGS = 0V, TJ = 125C nA VGS = 20V VGS = -20V f Dynamic Electrical Characteristics @ TJ = 25C (unless otherwise specified) Parameter Min. Typ. Max. Units Qg Qgs Qgd td(on) tr td(off) tf LD Total Gate Charge Gate-to-Source Charge Gate-to-Drain ("Miller") Charge Turn-On Delay Time Rise Time Turn-Off Delay Time Fall Time Internal Drain Inductance --- --- --- --- --- --- --- --- 180 46 65 19 140 97 100 5.0 270 --- --- --- --- --- --- --- LS Internal Source Inductance --- 13 --- Ciss Coss Crss Coss Coss Coss eff. Input Capacitance Output Capacitance Reverse Transfer Capacitance Output Capacitance Output Capacitance Effective Output Capacitance --- --- --- --- --- --- 7500 970 510 3640 650 1020 --- --- --- --- --- --- nC ns nH Conditions ID = 90A VDS = 60V VGS = 10V VDD = 38V ID = 90A RG = 2.5 VGS = 10V Between lead, f f D 6mm (0.25in.) from package pF G S and center of die contact VGS = 0V VDS = 25V = 1.0MHz, See Fig. 5 VGS = 0V, VDS = 1.0V, = 1.0MHz VGS = 0V, VDS = 60V, = 1.0MHz VGS = 0V, VDS = 0V to 60V Diode Characteristics Parameter Min. Typ. Max. Units IS Continuous Source Current --- --- 90 ISM (Body Diode) Pulsed Source Current --- --- 680 VSD trr Qrr ton (Body Diode) Diode Forward Voltage Reverse Recovery Time Reverse Recovery Charge Forward Turn-On Time --- --- --- --- 41 59 1.3 61 89 c Notes: Repetitive rating; pulse width limited by max. junction temperature. (See fig. 11). Limited by TJmax, starting TJ = 25C, L=0.13mH, RG = 25, IAS = 90A, VGS =10V. Part not recommended for use above this value. ISD 90A, di/dt 340A/s, VDD V(BR)DSS, TJ 175C. Pulse width 1.0ms; duty cycle 2%. 2 Conditions MOSFET symbol A V ns nC showing the integral reverse p-n junction diode. TJ = 25C, IS = 90A, VGS = 0V TJ = 25C, IF = 90A, VDD = 38V di/dt = 100A/s f f Intrinsic turn-on time is negligible (turn-on is dominated by LS+LD) Coss eff. is a fixed capacitance that gives the same charging time as Coss while VDS is rising from 0 to 80% VDSS. Limited by TJmax , see Fig.12a, 12b, 15, 16 for typical repetitive avalanche performance. This value determined from sample failure population, starting TJ = 25C, L=0.13mH, RG = 25, IAS = 90A, VGS =10V. R is measured at TJ of approximately 90C. www.irf.com AUIRFP2907Z Qualification Information Automotive (per AEC-Q101) Qualification Level Moisture Sensitivity Level Machine Model Comments: This part number(s) passed Automotive qualification. IR's Industrial and Consumer qualification level is granted by extension of the higher Automotive level. TO-247 MSL1 Class M4 (425V) AEC-Q101-002 ESD Human Body Model Class H2 (4000V) AEC-Q101-001 Charged Device Model RoHS Compliant Class C5 (1125V) AEC-Q101-005 Yes Qualification standards can be found at International Rectifiers web site: http//www.irf.com/ Exceptions to AEC-Q101 requirements are noted in the qualification report. www.irf.com 3 AUIRFP2907Z 1000 10000 VGS 15V 10V 8.0V 7.0V 6.0V 5.5V 5.0V 4.5V 1000 BOTTOM TOP ID, Drain-to-Source Current (A) ID, Drain-to-Source Current (A) TOP BOTTOM VGS 15V 10V 8.0V 7.0V 6.0V 5.5V 5.0V 4.5V 100 100 4.5V 10 4.5V 60s PULSE WIDTH 60s PULSE WIDTH Tj = 175C Tj = 25C 1 0.1 1 10 10 0.1 100 Fig 1. Typical Output Characteristics 100 200 Gfs, Forward Transconductance (S) ID, Drain-to-Source Current () 10 Fig 2. Typical Output Characteristics 1000 T J = 175C 100 10 T J = 25C 1 VDS = 25V 60s PULSE WIDTH 0.1 2 4 6 8 VGS, Gate-to-Source Voltage (V) Fig 3. Typical Transfer Characteristics 4 1 V DS, Drain-to-Source Voltage (V) V DS, Drain-to-Source Voltage (V) T J = 25C 150 T J = 175C 100 50 V DS = 10V 380s PULSE WIDTH 0 10 0 25 50 75 100 125 150 ID,Drain-to-Source Current (A) Fig 4. Typical Forward Transconductance vs. Drain Current www.irf.com nce AUIRFP2907Z 100000 12.0 VGS = 0V, f = 1 MHZ C iss = C gs + C gd, C ds SHORTED C rss = C gd ID= 90A 10000 Ciss Coss Crss 1000 VDS= 60V VDS= 38V 10.0 VGS, Gate-to-Source Voltage (V) C, Capacitance(pF) C oss = C ds + C gd VDS= 15V 8.0 6.0 4.0 2.0 100 0.0 1 10 100 0 VDS, Drain-to-Source Voltage (V) 100 150 200 QG Total Gate Charge (nC) Fig 6. Typical Gate Charge vs. Gate-to-Source Voltage Fig 5. Typical Capacitance vs. Drain-to-Source Voltage 1000 10000 ID, Drain-to-Source Current (A) ISD, Reverse Drain Current (A) 50 1000 T J = 175C 100 TJ = 25C 10 OPERATION IN THIS AREA LIMITED BY R DS(on) 100 100sec 10 1msec 1 VGS = 0V 1 10msec Tc = 25C Tj = 175C Single Pulse 0.1 0.0 0.5 1.0 1.5 2.0 VSD, Source-to-Drain Voltage (V) Fig 7. Typical Source-Drain Diode Forward Voltage www.irf.com 2.5 1 10 100 1000 VDS, Drain-to-Source Voltage (V) Fig 8. Maximum Safe Operating Area 5 AUIRFP2907Z 175 RDS(on) , Drain-to-Source On Resistance (Normalized) 2.5 ID, Drain Current (A) 150 125 100 75 50 25 0 ID = 90A VGS = 10V 2.0 1.5 1.0 0.5 25 50 75 100 125 150 -60 -40 -20 0 175 T C , Case Temperature (C) 20 40 60 80 100 120 140 160 180 T J , Junction Temperature (C) Fig 10. Normalized On-Resistance vs. Temperature Fig 9. Maximum Drain Current vs. Case Temperature 1 Thermal Response ( Z thJC ) D = 0.50 0.1 0.20 0.10 0.05 0.02 0.01 0.01 0.001 J SINGLE PULSE ( THERMAL RESPONSE ) R1 R1 J 1 1 R2 R2 2 R3 R3 3 2 Ci= i/Ri Ci i/Ri C 3 Ri (C/W) 0.1224 i (sec) 0.000360 0.1238 0.001463 0.2433 0.021388 Notes: 1. Duty Factor D = t1/t2 2. Peak Tj = P dm x Zthjc + Tc 0.0001 1E-006 1E-005 0.0001 0.001 0.01 0.1 t1 , Rectangular Pulse Duration (sec) Fig 11. Maximum Effective Transient Thermal Impedance, Junction-to-Case 6 www.irf.com 1 AUIRFP2907Z DRIVER L VDS D.U.T RG + V - DD IAS VGS 20V tp A 0.01 Fig 12a. Unclamped Inductive Test Circuit V(BR)DSS EAS , Single Pulse Avalanche Energy (mJ) 2500 15V ID 16A 25A BOTTOM 90A TOP 2000 1500 1000 500 tp 0 25 50 75 100 125 150 175 Starting T J , Junction Temperature (C) I AS Fig 12c. Maximum Avalanche Energy vs. Drain Current Fig 12b. Unclamped Inductive Waveforms QG 10 V QGS QGD 4.0 Charge Fig 13a. Basic Gate Charge Waveform L DUT 0 1K Fig 13b. Gate Charge Test Circuit www.irf.com VCC VGS(th) Gate threshold Voltage (V) VG 3.5 3.0 2.5 ID = 250A 2.0 1.5 1.0 -75 -50 -25 0 25 50 75 100 125 150 175 200 T J , Temperature ( C ) Fig 14. Threshold Voltage vs. Temperature 7 AUIRFP2907Z Avalanche Current (A) 1000 Duty Cycle = Single Pulse Allowed avalanche Current vs avalanche pulsewidth, tav assuming Tj = 25C due to avalanche losses 100 0.01 0.05 0.10 10 1 1.0E-05 1.0E-04 1.0E-03 1.0E-02 1.0E-01 tav (sec) Fig 15. Typical Avalanche Current Vs.Pulsewidth EAR , Avalanche Energy (mJ) 600 TOP Single Pulse BOTTOM 1% Duty Cycle ID = 90A 500 400 300 200 100 0 25 50 75 100 125 150 Starting T J , Junction Temperature (C) Fig 16. Maximum Avalanche Energy vs. Temperature 8 175 Notes on Repetitive Avalanche Curves , Figures 15, 16: (For further info, see AN-1005 at www.irf.com) 1. Avalanche failures assumption: Purely a thermal phenomenon and failure occurs at a temperature far in excess of T jmax. This is validated for every part type. 2. Safe operation in Avalanche is allowed as long asT jmax is not exceeded. 3. Equation below based on circuit and waveforms shown in Figures 12a, 12b. 4. PD (ave) = Average power dissipation per single avalanche pulse. 5. BV = Rated breakdown voltage (1.3 factor accounts for voltage increase during avalanche). 6. Iav = Allowable avalanche current. 7. T = Allowable rise in junction temperature, not to exceed Tjmax (assumed as 25C in Figure 15, 16). tav = Average time in avalanche. D = Duty cycle in avalanche = tav *f ZthJC(D, tav ) = Transient thermal resistance, see figure 11) PD (ave) = 1/2 ( 1.3*BV*Iav) = DT/ ZthJC Iav = 2DT/ [1.3*BV*Zth] EAS (AR) = PD (ave)*tav www.irf.com AUIRFP2907Z D.U.T Driver Gate Drive + - P.W. + D.U.T. ISD Waveform Reverse Recovery Current + V DD * dv/dt controlled by RG * Driver same type as D.U.T. * I SD controlled by Duty Factor "D" * D.U.T. - Device Under Test P.W. Period * RG D= VGS=10V Circuit Layout Considerations * Low Stray Inductance * Ground Plane * Low Leakage Inductance Current Transformer - Period + Body Diode Forward Current di/dt D.U.T. VDS Waveform Diode Recovery dv/dt Re-Applied Voltage - Body Diode VDD Forward Drop Inductor Curent Ripple 5% * ISD VGS = 5V for Logic Level Devices Fig 17. Peak Diode Recovery dv/dt Test Circuit for N-Channel HEXFET(R) Power MOSFETs V DS V GS RG RD D.U.T. + -V DD 10V Pulse Width 1 s Duty Factor 0.1 % Fig 18a. Switching Time Test Circuit VDS 90% 10% VGS td(on) tr t d(off) tf Fig 18b. Switching Time Waveforms www.irf.com 9 AUIRFP2907Z TO-247AC Package Outline Dimensions are shown in millimeters (inches) TO-247AC Part Marking Information Part Number AUFP2907Z YWWA IR Logo XX or Date Code Y= Year WW= Work Week A= Automotive, LeadFree XX Lot Code TO-247AC package is not recommended for Surface Mount Application. Note: For the most current drawing please refer to IR website at http://www.irf.com/package/ 10 www.irf.com AUIRFP2907Z Ordering Information Base part AUIRFP2907Z www.irf.com Package Type TO-247 Standard Pack Form Tube Complete Part Number Quantity 25 AUIRFP2907Z 11 AUIRFP2907Z IMPORTANT NOTICE Unless specifically designated for the automotive market, International Rectifier Corporation and its subsidiaries (IR) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or services without notice. Part numbers designated with the "AU" prefix follow automotive industry and / or customer specific requirements with regards to product discontinuance and process change notification. All products are sold subject to IR's terms and conditions of sale supplied at the time of order acknowledgment. IR warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with IR's standard warranty. Testing and other quality control techniques are used to the extent IR deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. IR assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using IR components. To minimize the risks with customer products and applications, customers should provide adequate design and operating safeguards. Reproduction of IR information in IR data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alterations is an unfair and deceptive business practice. IR is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of IR products or serviced with statements different from or beyond the parameters stated by IR for that product or service voids all express and any implied warranties for the associated IR product or service and is an unfair and deceptive business practice. IR is not responsible or liable for any such statements. IR products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or in other applications intended to support or sustain life, or in any other application in which the failure of the IR product could create a situation where personal injury or death may occur. Should Buyer purchase or use IR products for any such unintended or unauthorized application, Buyer shall indemnify and hold International Rectifier and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that IR was negligent regarding the design or manufacture of the product. IR products are neither designed nor intended for use in military/aerospace applications or environments unless the IR products are specifically designated by IR as military-grade or "enhanced plastic." Only products designated by IR as military-grade meet military specifications. Buyers acknowledge and agree that any such use of IR products which IR has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. IR products are neither designed nor intended for use in automotive applications or environments unless the specific IR products are designated by IR as compliant with ISO/TS 16949 requirements and bear a part number including the designation "AU". Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, IR will not be responsible for any failure to meet such requirements. For technical support, please contact IR's Technical Assistance Center http://www.irf.com/technical-info/ WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245 Tel: (310) 252-7105 12 www.irf.com