HCPL-0700#060 - Avago Technologies

Features

 High current transfer ratio – 2000% typical (4500 %

typical for HCNW139/138)

 Low input current requirements – 0.5 mA

 TTL compatible output – 0.1 V VOL typical

 Performance guaranteed over temperature 0°C

to 70°C

 Base access allows gain bandwidth adjustment

 High output current – 60 mA

 Safetyapproval

UL recognized – 3750 V rms for 1 minute and 5000 V

rms* for 1 minute per UL 1577

CSA approved

IEC/EN/DIN EN 60747-5-2 approved with VIORM = 1414

peak for HCNW139 and HCNW138

 Available in 8-Pin DIP or SOIC-8 footprint or widebody

package

 MIL-PRF-38534 hermetic version available

(HCPL-5700/1)

Applications

 Ground isolate most logic families – TTL/TTL, CMOS/

TTL, CMOS/CMOS, LSTTL/TTL, CMOS/LSTTL

 Low input current line receiver

 High voltage insulation (HCNW139/138)

 EIA RS-232C line receiver

 Telephone ring detector

 117 V ac line voltage status indicator – low input

power dissipation

 Low power systems – ground isolation

CAUTION: It is advised that normal static precautions be taken in handling and assembly

of this component to prevent damage and/or degradation which may be induced by ESD.

*5000 V rms/1 minute rating is for HCNW139/138 and Option 020

(6N139/138) products only.

A 0.1 μF bypass capacitor connected between pins 8 and 5 is

recommended.

6N139, 6N138, HCPL-0701, HCPL-0700,

HCNW138, HCNW139

Low Input Current, High Gain Optocouplers

Data Sheet

Description

These high gain series couplers use a Light Emitting

Diode and an integrated high gain photodetec tor to

provide extremely high current transfer ratio between

input and output. Separate pins for the photodiode

and output stage result in TTL compatible saturation

voltages and high speed operation. Where desired the

VCC and VO terminals may be tied together to achieve

conven tional photodarlington operation. A base

access terminal allows a gain bandwidth adjustment to

be made.

The 6N139, HCPL-0701, and CNW139 are for use in CMOS,

LSTTL or other low power appli ca tions. A 400% mini-

mum current transfer ratio is guaranteed over 0 to 70°C

operating range for only 0.5 mA of LED current.

The 6N138, HCPL-0700, and HCNW138 are designed for

use mainly in TTL applications. Current Transfer Ratio

(CTR) is 300% minimum over 0 to 70°C for an LED current

of 1.6 mA (1 TTL Unit load ). A 300% minimum CTR

enables operation with 1 TTL Load using a 2.2 kΩ

pull-up resistor.

Functional Diagram

Lead (Pb) Free

RoHS 6 fully

compliant

RoHS 6 fully compliant options available;

-xxxE denotes a lead-free product

ANODE

CATHODE

VCC

GND

TRUTH TABLE

LED

OFF

LOW

HIGH

Selection for lower input current down to 250 μA is

available upon request.

The HCPL-0701 and HCPL-0700 are surface mount devices

packaged in an industry standard SOIC-8 footprint.

The SOIC-8 does not require “through holes” in a PCB.

This package occupies approximately one-third the

footprint area of the standard dual-in-line package. The

lead pro le is designed to be compatible with standard

surface mount processes.

The HCNW139 and HCNW138 are packaged in a

widebody encapsulation that provides creep age and

clearance dimensions suitable for safety approval by

regulatory agencies worldwide.

Selection Guide

Widebody

8-Pin DIP Package Hermetic

(300 Mil) Small Outline SO-8 (400 mil) Single and

Dual Single Dual Minimum Absolute Dual

Single Channel Channel Channel Single Input ON Maxi- Channel

Channel Package Package Package Channel Current Minimum mum Packages

Package HCPL- HCPL- HCPL- Package (IF) CTR V

CC HCPL-

6N139 2731[1] 0701 0731 HCNW139 0.5 mA 400% 18 V

6N138 2730[1] 0700 0730 HCNW138 1.6 mA 300% 7 V

HCPL-4701[1] 4731[1] 070A[1] 073A[1] 40 μA 800% 18 V

0.5 mA 300% 20 V 5701[1]

5700[1]

5731[1]

5730[1]

Note:

1. Technical data are on separate Avago publications.

Schematic

Ordering Information

6N138, 6N139, HCPL-0700 and HCPL-0701 are UL Recognized with 3750 Vrms for 1 minute per UL1577 and are ap-

proved under CSA Component Acceptance Notice #5, File CA 88324.

Part

Number

Option

Package

Surface

Mount

Gull

Wing

Tape

& Reel

UL 5000 Vrms/

1 Minute

rating

IEC/EN/DIN

EN 60747-5-2 Quantity

RoHS

Compliant

non RoHS

Compliant

6N138

6N139

-000E no option

300 mil

DIP-8

50 per tube

-300E #300 X X 50 per tube

-500E #500 X X X 1000 per reel

-020E #020 X 50 per tube

-320E #320 X X X 50 per tube

-520E #520 X X X X 1000 per reel

-060E #060 X 50 per tube

-360E #360 X X X 50 per tube

-560E #560 X X X X 1000 per reel

HCPL-0700

HCPL-0701

-000E no option

SO-8

X 100 per tube

-500E #500 X X 1500 per reel

-060E #060 X X 100 per tube

-560E #560 X X X 1500 per reel

HCNW138

HCNW139

-000E no option 400 mil

Widebody

DIP-8

42 per tube

-300E #300 X X 42 per tube

-500E #500 X X X 750 per reel

To order, choose a part number from the part number

column and combine with the desired option from

the option column to form an order entry.

Example 1:

6N138-560E to order product of 300 mil DIP Gull Wing

Surface Mount package in Tape and Reel packaging

with IEC/EN/DIN EN 60747-5-2 Safety Approval and

RoHS compliant.

Example 2:

HCPL-0700 to order product of 300 mil DIP package in

Tube packaging and non RoHS compliant.

Option datasheets are available. Contact your Avago sales

representative or authorized distributor for information.

Remarks: The notation ‘#XXX’ is used for existing

products, while (new) products launched since July 15,

2001 and RoHS compliant will use ‘–XXXE.’

VCC

ICC

ANODE

CATHODE

–

5GND

SHIELD

Package Outline Drawings

8-Pin DIP Package (6N139/6N138)**

8-Pin DIP Package with Gull Wing Surface Mount Option 300 (6N139/6N138)

**JEDEC Registered Data.

1.080 ± 0.320

(0.043 ± 0.013) 2.54 ± 0.25

(0.100 ± 0.010)

0.51 (0.020) MIN.

0.65 (0.025) MAX.

4.70 (0.185) MAX.

2.92 (0.115) MIN.

5° TYP. 0.254 + 0.076

- 0.051

(0.010+ 0.003)

- 0.002)

7.62 ± 0.25

(0.300 ± 0.010)

6.35 ± 0.25

(0.250 ± 0.010)

9.65 ± 0.25

(0.380 ± 0.010)

1.78 (0.070) MAX.

1.19 (0.047) MAX.

A XXXXZ

YYWW

DATE CODE

DIMENSIONS IN MILLIMETERS AND (INCHES).

5678

4321

OPTION CODE*

RECOGNITION

TYPE NUMBER

* MARKING CODE LETTER FOR OPTION NUMBERS

"L" = OPTION 020

OPTION NUMBERS 300 AND 500 NOT MARKED.

NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.

3.56 ± 0.13

(0.140 ± 0.005)

0.635 ± 0.25

(0.025 ± 0.010) 12° NOM.

9.65 ± 0.25

(0.380 ± 0.010)

0.635 ± 0.130

(0.025 ± 0.005)

7.62 ± 0.25

(0.300 ± 0.010)

9.65 ± 0.25

(0.380 ± 0.010)

6.350 ± 0.25

(0.250 ± 0.010)

1.016 (0.040)

1.27 (0.050)

10.9 (0.430)

2.0 (0.080)

LAND PATTERN RECOMMENDATION

1.080 ± 0.320

(0.043 ± 0.013)

3.56 ± 0.13

(0.140 ± 0.005)

1.780

(0.070)

MAX.

1.19

(0.047)

MAX.

2.54

(0.100)

BSC

DIMENSIONS IN MILLIMETERS (INCHES).

LEAD COPLANARITY = 0.10 mm (0.004 INCHES).

NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.

0.254 + 0.076

- 0.051

(0.010+ 0.003)

- 0.002)

Small Outline SO-8 Package (HCPL-0701/HCPL-0700)

8-Pin Widebody DIP Package (HCNW139/HCNW138)

7.49 (0.295)

1.9 (0.075)

0.64 (0.025)

LAND PATTERN RECOMMENDATION

XXX

YWW

8765

4321

5.994 ± 0.203

(0.236 ± 0.008)

3.937 ± 0.127

(0.155 ± 0.005)

0.406 ± 0.076

(0.016 ± 0.003) 1.270

(0.050) BSC

5.080 ± 0.127

(0.200 ± 0.005)

3.175 ± 0.127

(0.125 ± 0.005) 1.524

(0.060)

45° X 0.432

(0.017)

0.228 ± 0.025

(0.009 ± 0.001)

TYPE NUMBER

(LAST 3 DIGITS)

DATE CODE

0.305

(0.012) MIN.

TOTAL PACKAGE LENGTH (INCLUSIVE OF MOLD FLASH)

5.207 ± 0.254 (0.205 ± 0.010)

DIMENSIONS IN MILLIMETERS (INCHES).

LEAD COPLANARITY = 0.10 mm (0.004 INCHES) MAX.

NOTE: FLOATING LEAD PROTRUSION IS 0.15 mm (6 mils) MAX.

0.203 ± 0.102

(0.008 ± 0.004)

7°

PIN ONE

0 ~ 7°

11.23 ± 0.15

(0.442 ± 0.006)

1.80 ± 0.15

(0.071 ± 0.006)

5.10

(0.201)MAX.

1.55

(0.061)

MAX.

2.54 (0.100)

TYP.

DIMENSIONS IN MILLIMETERS (INCHES).

NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.

7° TYP.

0.254 + 0.076

- 0.0051

(0.010+ 0.003)

- 0.002)

11.00

(0.433)

9.00 ± 0.15

(0.354 ± 0.006)

MAX.

10.16 (0.400)

TYP.

HCNWXXXX

YYWW

DATE CODE

TYPE NUMBER

0.51 (0.021) MIN.

0.40 (0.016)

0.56 (0.022)

3.10 (0.122)

3.90 (0.154)

8-Pin Widebody DIP Package with Gull Wing Surface Mount Option 300 (HCNW139/HCNW138)

Solder Re ow Temperature Pro le

TIME (SECONDS)

TEMPERATURE (°C)

200

100

50 150100 200 250

300

SEC.

50 SEC.

SEC.

160 °C

140 °C

150 °C

PEAK

TEMP.

245 °C

PEAK

TEMP.

240 °CPEAK

TEMP.

230 °C

SOLDERING

TIME

200 °C

PREHEATING TIME

150 °C, 90 + 30 SEC.

2.5 C ± 0.5 °C/SEC.

3 °C + 1 °C/–0.5 °C

TIGHT

TYPICAL

LOOSE

ROOM

TEMPERATURE

PREHEATING RATE 3 °C + 1 °C/–0.5 °C/SEC.

REFLOW HEATING RATE 2.5 °C ± 0.5 °C/SEC.

NOTE: NON-HALIDE FLUX SHOULD BE USED.

1.00 ± 0.15

(0.039 ± 0.006)

7° NOM.

12.30 ± 0.30

(0.484 ± 0.012)

0.75 ± 0.25

(0.030 ± 0.010)

11.00

(0.433)

11.23 ± 0.15

(0.442 ± 0.006)

9.00 ± 0.15

(0.354 ± 0.006)

1.3

(0.051)

13.56

(0.534)

2.29

(0.09)

LAND PATTERN RECOMMENDATION

1.80 ± 0.15

(0.071 ± 0.006)

4.00

(0.158)MAX.

1.55

(0.061)

MAX.

2.54

(0.100)

BSC

DIMENSIONS IN MILLIMETERS (INCHES).

LEAD COPLANARITY = 0.10 mm (0.004 INCHES).

NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.

0.254 + 0.076

- 0.0051

(0.010+ 0.003)

- 0.002)

MAX.

Regulatory Information

The 6N139/138, HCNW139/138, and HCPL-0701/0700 have been approved by the following organizations:

IEC/EN/DIN EN 60747-5-2

Approved under

IEC 60747-5-2:1997 + A1:2002

EN 60747-5-2:2001 + A1:2002

DIN EN 60747-5-2 (VDE 0884 Teil 2):2003-01

(HCNW139/138 only)

Recommended Pb-Free IR Pro le

Insulation and Safety Related Speci cations

8-Pin DIP Widebody

(300 Mil) SO-8 (400 Mil)

Parameter Symbol Value Value Value Units Conditions

Minimum External L(101) 7.1 4.9 9.6 mm Measured from input terminals

Air Gap (External to output terminals, shortest

Clearance) distance through air.

Minimum External L(102) 7.4 4.8 10.0 mm Measured from input terminals

Tracking (External to output terminals, shortest

Creepage) distance path along body.

Minimum Internal 0.08 0.08 1.0 mm Through insulation distance,

Plastic Gap conductor to conductor, usually

(Internal Clearance) the direct distance between the

photoemitter and photodetector

inside the optocoupler cavity.

Minimum Internal NA NA 4.0 mm Measured from input terminals

Tracking (Internal to output terminals, along

Creepage) internal cavity.

Tracking Resistance CTI 200 200 200 Volts DIN IEC 112/VDE 0303 Part 1

(Comparative

Tracking Index)

Isolation Group IIIa IIIa IIIa Material Group

(DIN VDE 0110, 1/89, Table 1)

Option 300 - surface mount classi cation is Class A in accordance with CECC 00802.

Recognized under UL 1577, Component Recognition

Program, File E55361.

CSA

Approved under CSA Component Acceptance Notice

#5, File CA 88324.

217 °C

RAMP-DOWN

6 °C/SEC. MAX.

RAMP-UP

3 °C/SEC. MAX.

150 - 200 °C

* 260 +0/-5 °C

t 25 °C to PEAK

60 to 150 SEC.

15 SEC.

TIME WITHIN 5 °C of ACTUAL

PEAK TEMPERATURE

PREHEAT

60 to 180 SEC.

Tsmax

Tsmin

TIME

TEMPERATURE

NOTES:

THE TIME FROM 25 °C to PEAK

TEMPERATURE = 8 MINUTES MAX.

Tsmax = 200 °C, Tsmin = 150 °C

NOTE: NON-HALIDE FLUX SHOULD BE USED.

* RECOMMENDED PEAK TEMPERATURE FOR

WIDEBODY 400mils PACKAGE IS 245 °C

IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics (HCNW139 and HCNW138)

Description Symbol Characteristic Units

Installation Classi cation per DIN VDE 0110/1.89, Table 1

for rated mains voltage ≤600 V rms I-IV

for rated mains voltage ≤1000 V rms I-III

Climatic Classi cation 55/100/21

Pollution Degree (DIN VDE 0110/1.89) 2

Maximum Working Insulation Voltage VIORM 1414 Vpeak

Input to Output Test Voltage, Method b*

PR = 1.875 x VIORM, 100% Production Test with tP = 1 sec, VPR 2652 Vpeak

Partial Discharge < 5 pC

Input to Output Test Voltage, Method a*

PR = 1.5 x VIORM, Type and Sample Test, VPR 2121 Vpeak

P = 60 sec, Partial Discharge < 5 pC

Highest Allowable Overvoltage*

(Transient Overvoltage, tini = 10 sec) VIOTM 8000 Vpeak

Safety Limiting Values

(Maximum values allowed in the event of a failure,

also see Figure 11, Thermal Derating curve.)

Case Temperature TS 175 °C

Current (Input Current IF, PS = 0) IS,INPUT 400 mA

Output Power PS,OUTPUT 700 mW

Insulation Resistance at TS, VIO = 500 V RS > 109 

*Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section, IEC/EN/DIN EN 60747-5-2, for a

detailed description.

Note: Isolation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in applica-

tion.

Recommended Operating Conditions

Parameter Symbol Min. Max. Units

Power Supply Voltage VCC 4.5 18 V

Forward Input Current (ON) IF(ON) 0.5 12.0 mA

Forward Input Voltage (OFF) VF(OFF) 0 0.8 V

Operating Temperature TA 0 70 °C

Absolute Maximum Ratings* (No Derating Required up to 85°C)

Parameter Symbol Min. Max. Units

Storage Temperature TS -55 125 °C

Operating Temperature** TA -40 85 °C

Average Forward Input Current IF(AVG) 20 mA

Peak Forward Input Current IFPK 40 mA

(50% Duty Cycle, 1 ms Pulse Width)

Peak Transient Input Current IF(TRAN) 1.0 A

(<1 μs Pulse Width, 300 pps)

Reverse Input Voltage VR 5 V

HCNW139/138 3 V

Input Power Dissipation PI 35 mW

Output Current (Pin 6) IO 60 mA

Emitter Base Reverse Voltage (Pin 5-7) VEB 0.5 V

Supply Voltage and Output Voltage VCC -0.5 18 V

(6N139, HCPL-0701, HCNW139)

Supply Voltage and Output Voltage VCC -0.5 7 V

(6N138, HCPL-0700, HCNW138)

Output Power Dissipation PO 100 mW

Total Power Dissipation PT 135 mW

Lead Solder Temperature (for Through Hole Devices) 260°C for 10 sec., 1.6 mm below seating plane

HCNW139/138 260°C for 10 sec., up to seating plane

Re ow Temperature Pro le See Package Outline Drawings section

(for SOIC-8 and Option #300)

*JEDEC Registered Data for 6N139 and 6N138.

**0°C to 70°C on JEDEC Registration.

Electrical Speci cations

0°C ≤ TA ≤ 70°C, 4.5 V ≤ VCC ≤ 18 V, 0.5 mA ≤ IF(ON) ≤ 12 mA, 0 V ≤ VF(OFF) ≤ 0.8 V, unless otherwise speci ed.

All Typicals at TA = 25°C. See Note 7.

Parameter Sym. Device Min. Typ.** Max. Units Test Conditions Fig. Note

Current Transfer CTR 6N139 400* 2000 5000 % IF = 0.5 mA VCC = 4.5 2, 3 1, 2,

Ratio HCPL-0701 VO = 0.4 V 4

HCNW139 400 4500

6N139 500* 1600 2600 IF = 1.6 mA

HCPL-0701

HCNW139 500 3000

300 1600 IF = 5.0 mA

200 850 IF = 12 mA

6N138 300* 1600 2600 IF = 1.6 mA

HCPL-0700

HCNW138 1500

Logic Low Output VOL 6N139 0.1 0.4 V IF = 0.5 mA, VCC = 4.5 1 2

Voltage HCPL-0701 IO = 2 mA

HCNW139

F = 1.6 mA,

O = 8 mA

F = 5.0 mA,

O = 15 mA

0.2 IF = 12 mA,

O = 24 mA

6N138 0.1 IF = 1.6 mA,

HCPL-0700 IO = 4.8 mA

HCNW138

Logic High IOH 6N139 0.05 100 μA VO = VCC = 18 V IF = 0 mA 2

Output Current HCPL-0701

HCNW139

6N138 0.1 250 VO = VCC = 7 V

HCPL-0700

HCNW138

Logic Low Supply ICCL 6N138/139 0.4 1.5 mA IF = 1.6 mA, VO = Open, 10 2

Current HCPL-0701/ VCC = 18 V

0700

HCNW139 0.5 2

HCNW138

Logic High ICCH 6N138/139 0.01 10 μA IF = 0 mA, VO = Open, 2

Supply Current HCPL-0701/ VCC = 18 V

0700

HCNW139 1

HCNW138

Input Forward VF 6N138 1.25 1.40 1.7* V TA = 25°C IF = 1.6 mA 4, 8

Voltage 6N139

HCPL-0701 1.75

HCPL-0700

HCNW139 1.0 1.45 1.85 TA = 25°C

HCNW138

0.95 1.95

Input Reverse BVR 5.0* V IR = 10 μA, TA = 25°C

HCNW139 3.0 IR = 100 μA, TA = 25°C

HCNW138

Temperature ΔVF -1.8 mV/°C IF = 1.6 mA 8

Coe cient of ΔTA

Forward Voltage

Input CIN 60 pF f = 1 MHz, VF = 0 V

Capacitance HCNW139 90

HCNW138

* JEDEC Registered Data for 6N139 and 6N138.

**All typical values at TA = 25°C and VCC = 5 V, unless otherwise noted.

Breakdown Voltage

Switching Speci cations (AC)

Over recommended operating conditions (TA = 0 to 70°C), VCC = 5 V, unless otherwise speci ed.

Parameter Sym. Device Min. Typ.** Max. Units Test Conditions Fig. Note

A =25°C

Propagation tPHL 6N139 5 25* 30 s IF = 0.5 mA, 5, 6, 2, 4

Delay Time HCPL-0701 Rl = 4.7 k 7, 9,

to Logic Low HCNW139 12

6N139 0.2 1* 2 s IF = 12 mA,

HCPL-0701 Rl = 270 

HCNW139 11

6N138 1.6 10* 15 s IF = 1.6 mA,

HCPL-0700 Rl = 2.2 k

HCNW138 11

Propagation tPLH 6N139 18 60* 90 s IF = 0.5 mA, 5, 6, 2, 4

Delay Time HCPL-0701 Rl = 4.7 k 7, 9,

to Logic High HCNW139 115 12

6N139 2 7* 10 s IF = 12 mA,

HCPL-0701 Rl = 270 

HCNW139 11

6N138 10 35* 50 s IF = 1.6 mA,

HCPL-0700 Rl = 2.2 k

HCNW138 70

Common Mode |CMH| 1000 10000 V/s IF = 0 mA, 13 5, 6

Transient TA = 25°C

Immunity at Rl = 2.2 k

Logic High |VCM| = 10

Output Vp-p

Common Mode |CML| 1000 10000 V/s IF = 1.6 mA, 13 5, 6

Transient TA = 25°C

Immunity at Rl = 2.2 k

Logic Low |VCM| = 10

Output Vp-p

* JEDEC Registered Data for 6N139 and 6N138.

**All typical values at TA = 25°C and VCC = 5 V, unless otherwise noted.

at Output

Notes:

1. DC CURRENT TRANSFER RATIO (CTR) is de ned as the ratio of output collector current, IO, to the forward LED input current, IF, times 100%.

2. Pin 7 Open.

3. Device considered a two-terminal device. Pins 1, 2, 3, and 4 shorted together and Pins 5, 6, 7, and 8 shorted together.

4. Use of a resistor between pin 5 and 7 will decrease gain and delay time. Signi cant reduction in overall gain can occur when using resistor values

below 47 k. For more information, please contact your local Avago Components representative.

5. Common mode transient immunity in a Logic High level is the maximum toler able (positive) dVCM/dt of the common mode pulse, VCM, to assure

that the output will remain in a Logic High state (i.e., VO > 2.0 V). Common mode transient immunity in a Logic Low level is the maximum tolerable

(negative) dVCM/dt of the common mode pulse, VCM, to assure that the output will remain in a Logic Low state (i.e., VO < 0.8 V).

6. In applications where dV/dt may exceed 50,000 V/μs (such as static discharge) a series resistor, RCC, should be included to protect the

detector IC from destructively high surge currents. The recommended value is RCC = 220 .

7. Use of a 0.1 F bypass capacitor connected between pins 8 and 5 adjacent to the device is recommended.

8. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage 4500 V rms for 1 second (leakage detection

current limit, II-O < 5 A). This test is per formed before the 100% production test shown in the IEC/EN/DIN EN 60747-5-2 Insulation Related Char-

acteristics Table, if applicable.

9. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage > 6000 V rms for 1 second (leakage detection

current limit, II-O < 5 A). This test is per formed before the 100% production test for partial discharge (method b) shown in the IEC/EN/DIN EN

60747-5-2 Insulation Related Characteristics Table, if applicable.

Package Characteristics

Parameter Sym. Min. Typ.** Max. Units Test Conditions Fig. Note

Input-Output Momentary

Withstand Voltage†

VISO 3750 V rms RH < 50%, t = 1 min.,

TA = 25°C

3, 8

Option 020

HCNW139

HCNW138

5000 3, 9

Resistance (Input-Output) RI-O 1012 VI-O = 500 Vdc

RH < 45%

Capacitance (Input-Output) CI-O 0.6 pF f = 1 MHz 3

**All typicals at TA = 25°C, unless otherwise noted.

†The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage rating.

For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Table (if applicable), your equipment level safety

speci cation or Avago Application Note 1074 entitled “Optocoupler Input-Output Endurance Voltage.”

01.02.0

VO – OUTPUT VOLTAGE – V

IO – OUTPUT CURRENT – mA

5.0 mA

A = 25° C

VCC = 5 V

4.5 mA

4.0 mA

3.5 mA

3.0 mA

2.5 mA

2.0 mA

1.5 mA

1.0 mA

0.5 mA

IF – FORWARD CURRENT – mA

2000

1600

800

400

0.1 1.0

CTR – CURRENT TRANSFER RATIO – %

1200

VCC = 5 V

= 0.4 V

85°C

70°C

25°C

70°C

-40°C

IF – INPUT DIODE FORWARD CURRENT – mA

0.01

0.01 0.1 10

IO – OUTPUT CURRENT – mA

0.1

1.0

100

TA = 25° C

TA = 0° C

TA = 70° C

TA = 85° C

TA = -40° C

VF – FORWARD VOLTAGE – V

100

0.1

0.01

1.11.2 1.31.4

IF – FORWARD CURRENT – mA

1.61.5

1.0

0.001

1000

–

TA = 25°C

TA = 0°C

TA = 85°C

TA = 70°C

TA = -40°C

-60 -20 20 40 100

tP – PROPAGATION DELAY – μs

TA – TEMPERATURE – °C

60 80

-40

IF = 0.5 mA

RL = 4.7 kΩ

1/f = 50 μs

tPLH

tPHL

-60 -20 20 40 100

tP – PROPAGATION DELAY – μs

TA – TEMPERATURE – °C

60 80

-40

IF = 1.6 mA

RL = 2.2 kΩ

1/f = 50 μs

tPLH

tPHL

-60 -20 20 40 100

tP – PROPAGATION DELAY – μs

TA – TEMPERATURE – °C

60 80

-40

IF = 12 mA

RL = 270 kΩ

1/f = 50 μstPLH

tPHL

1.6

1.5

1.4

1.3

-60 -20 20 40 100

VF – FORWARD VOLTAGE – V

TA – TEMPERATURE – °C

60 80

-40

1.2

IF = 1.6 mA

RL – LOAD RESISTANCE – kΩ

100

0.1 1.0

TIME – μs

IF – ADJUSTED FOR VOL = 2 V

TA = 25° C tf

Figure 1. 6N138/6N139 DC transfer character-

istics

Figure 6. Propagation delay vs. temperatureFigure 5. Propagation delay vs. temperature

Figure 2. Current transfer ratio vs. forward

current 6N138/6N139

Figure 3. 6N138/6N139 output current vs. input

diode forward current

Figure 4. Input diode forward current vs.

forward voltage

Figure 7. Propagation delay vs. temperature Figure 8. Forward voltage vs. temperature Figure 9. Nonsaturated rise and fall times vs.

load resistance

PULSE

GEN.

Z = 50 Ω

t = 5 ns

I MONITOR

0.1 μF

CL = 15 pF*

tPHL tPLH

1.5 V 1.5 V

5 V

+5 V

10% DUTY CYCLE

I/f < 100 μs

(SATURATED

RESPONSE)

tftr

(NON-SATURATED

RESPONSE)

5 V

90%

10%

90%

10%

* INCLUDES PROBE AND

FIXTURE CAPACITANCE

PULSE GEN.

VCM

VFF

0 V 10%

90% 90%

10%

SWITCH AT A: I = 0 mA

SWITCH AT B: I = 1.6 mA

trtf

5 V

+5 V

–

RCC (SEE NOTE 6)

10 V tr, tf = 16 ns

For product information and a complete list of distributors, please go to our website: www.avagotech.com

Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies Limited in the United States and other countries.

AV02-1359EN - July 27, 2012

Figure 12. Switching test circuit

Figure 11. Thermal derating curve, dependence of safety limiting value

with case temperature per IEC/EN/DIN EN 60747-5-2

Figure 10. Logic low supply current vs. forward current

Figure 13. Test circuit for transient immunity and typical waveforms

0.8

0.6

0.4

0.2

04 810 16

ICCL – LOGIC LOW SUPPLY CURRENT – mA

IF – FORWARD CURRENT

12 14

VCC = 18 V

0.1

0.3

0.5

0.7

VCC = 5 V

OUTPUT POWER – PS, INPUT CURRENT – IS

TS – CASE TEMPERATURE – °C

175

1000

400

12525 75 100 150

600

800

200

100

300

500

700

900 PS (mW)

IS (mA)

WIDEBODY