R Mobile Intel(R) Celeron(R) Processor (0.13) in Micro-FCBGA Package at Low Voltage 650 MHz Datasheet October 2001 Order Number: 298517-001 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet Information in this document is provided in connection with Intel products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Intel's Terms and Conditions of Sale for such products, Intel assumes no liability whatsoever, and Intel disclaims any express or implied warranty, relating to sale and/or use of Intel products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right. Intel products are not intended for use in medical, life saving, or life sustaining applications. Intel may make changes to specifications and product descriptions at any time, without notice. Designers must not rely on the absence or characteristics of any features or instructions marked "reserved" or "undefined." Intel reserves these for future definition and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future changes to them. The Mobile Intel CeleronTM Processor may contain design defects or errors known as errata which may cause the product to deviate from published specifications. Current characterized errata are available on request. Contact your local Intel sales office or your distributor to obtain the latest specifications and before placing your product order. Copies of documents which have an ordering number and are referenced in this document, or other Intel literature, may be obtained from: Intel Corporation www.intel.com or call 1-800-548-4725 Intel(R), Pentium(R), Celeron(R), and SpeedStepTM are registered trademarks or trademarks of Intel Corporation in the United States and other countries. *Other names and brands may be claimed as the property of others. Copyright (c) Intel Corporation 2000-2001 2 Datasheet 298517-001 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet Contents 1. Introduction.......................................................................................................................................9 1.1 1.2 1.3 2. Mobile Intel Celeron Processor Features .......................................................................................12 2.1 2.2 2.3 2.4 3. New Features in the Mobile Intel Celeron Processor...........................................12 2.1.1 256K On-die Integrated L2 Cache ..........................................................12 2.1.2 Data Prefetch Logic.................................................................................12 2.1.3 Signal Differences Between the Mobile Intel Celeron Processor (0.18) (in BGA2 and Micro-PGA2 Packages) and the Mobile Intel Celeron Processor (0.13) (in Micro-FCBGA Package) ........................................................13 Power Management .............................................................................................13 2.2.1 Clock Control Architecture.......................................................................13 2.2.2 Normal State ...........................................................................................13 2.2.3 Auto Halt State ........................................................................................13 2.2.4 Quick Start State .....................................................................................14 2.2.5 HALT/Grant Snoop State ........................................................................15 2.2.6 Deep Sleep State ....................................................................................15 2.2.7 Operating System Implications of Low-power States .............................16 AGTL Signals .......................................................................................................16 Mobile Intel Celeron Processor CPUID................................................................16 Electrical Specifications..................................................................................................................18 3.1 3.2 3.3 3.4 3.5 3.6 4. Overview.................................................................................................................9 Terminology..........................................................................................................10 References ...........................................................................................................11 Processor System Signals ...................................................................................18 3.1.1 Power Sequencing Requirements...........................................................19 3.1.2 Test Access Port (TAP) Connection .......................................................19 3.1.3 Catastrophic Thermal Protection.............................................................20 3.1.4 Unused Signals .......................................................................................20 3.1.5 Signal State in Low-power States ...........................................................20 3.1.5.1 System Bus Signals ..............................................................20 3.1.5.2 CMOS and Open-drain Signals.............................................20 3.1.5.3 Other Signals.........................................................................21 Power Supply Requirements................................................................................21 3.2.1 Decoupling Guidelines ............................................................................21 3.2.2 Voltage Planes ........................................................................................21 3.2.3 Voltage Identification ...............................................................................22 System Bus Clock and Processor Clocking .........................................................23 Maximum Ratings.................................................................................................23 DC Specifications .................................................................................................24 AC Specifications .................................................................................................29 3.6.1 System Bus, Clock, APIC, TAP, CMOS, and Open-drain AC Specifications ..........................................................................................29 System Signal Simulations .............................................................................................................42 298517-001 Datasheet 3 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet 4.1 4.2 4.3 5. Mechanical Specifications.............................................................................................................. 47 5.1 5.2 6. Thermal Diode ..................................................................................................... 58 Processor Initialization and Configuration ..................................................................................... 60 7.1 7.2 8. Surface Mount Micro-FCBGA Package ............................................................... 47 Signal Listings...................................................................................................... 51 VCC Thermal Specifications............................................................................................................ 58 6.1 7. System Bus Clock (BCLK) and PICCLK DC Specifications and AC Signal Quality Specifications....................................................................................................... 42 AGTL AC Signal Quality Specifications ............................................................... 44 Non-AGTL Signal Quality Specifications ............................................................. 45 4.3.1 PWRGOOD, VTTPWRGD Signal Quality Specifications ....................... 46 Description ........................................................................................................... 60 7.1.1 Quick Start Enable .................................................................................. 60 7.1.2 System Bus Frequency........................................................................... 60 7.1.3 APIC Enable ........................................................................................... 60 Clock Frequencies and Ratios ............................................................................. 60 Processor Interface........................................................................................................................ 61 8.1 8.2 Alphabetical Signal Reference............................................................................. 61 Signal Summaries................................................................................................ 71 Appendix A. PLL RLC Filter Specification .................................................................................................. 73 A1. A2. A3. A4. 4 Introduction ......................................................................................................... 73 Filter Specification............................................................................................... 73 Recommendation for Mobile Systems ................................................................ 74 Comments........................................................................................................... 75 Datasheet 298517-001 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet Figures Figure 1. Clock Control States ..........................................................................................14 Figure 2. PLL RLC Filter....................................................................................................22 Figure 3. VTTPWRGD System-Level Connections...........................................................23 Figure 4. Illustration of VCC Static and Transient Tolerances (VID = 1.15V)....................26 Figure 5. Illustration of Deep Sleep VCC Static and Transient Tolerances (VID Setting = 1.15V)................................................................................................................26 Figure 6. BCLK/PICCLK/TCK Generic Clock Timing Waveform ......................................34 Figure 7. Valid Delay Timings ...........................................................................................34 Figure 8. Setup and Hold Timings.....................................................................................35 Figure 9. Cold/Warm Reset and Configuration Timings ...................................................35 Figure 10. Power-on Sequence and Reset Timings .........................................................36 Figure 11. Power Down Sequencing and Timings (VCC Leading) ...................................37 Figure 12. Power Down Sequencing and Timings (VCCT Leading) ....................................38 Figure 13. Test Timings (Boundary Scan) .........................................................................39 Figure 14. Test Reset Timings ..........................................................................................39 Figure 15. Quick Start/Deep Sleep Timing (BCLK Stopping Method) ...............................40 Figure 16. Quick Start/Deep Sleep Timing (DPSLP# Assertion Method) .........................41 Figure 17. BCLK/PICCLK Generic Clock Waveform.........................................................43 Figure 18. Maximum Acceptable Overshoot/Undershoot Waveform................................44 Figure 19. Micro-FCBGA Package - Top and Bottom Isometric Views............................48 Figure 20. Micro-FCBGA Package - Top and Side Views ...............................................49 Figure 21. Micro-FCBGA Package - Bottom View ............................................................50 Figure 22. Pin/Ball Map - Top View...................................................................................51 Figure 23. PLL Filter Specifications ..................................................................................74 298517-001 Datasheet 5 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet Tables Table 1. New and Revised Mobile Intel Celeron Processor (0.13) Signals.................... 13 Table 2. Clock State Characteristics................................................................................. 16 Table 3. Mobile Intel Celeron Processor CPUID .............................................................. 17 Table 4. Mobile Intel Celeron Processor CPUID Cache and TLB Descriptors................. 17 Table 5. System Signal Groups ........................................................................................ 18 Table 6. Recommended Resistors for Mobile Intel Celeron Processor Signals............... 19 Table 7. Mobile Intel Celeron Processor VID Values ....................................................... 22 Table 8. Mobile Intel Celeron Processor Absolute Maximum Ratings ............................. 24 Table 9. Power Specifications for Mobile Intel Celeron Processor ................................... 25 Table 10. VCC Tolerances for the Low Voltage Mobile Intel Celeron Processor: VID = 1.15V ............................................................................................................. 27 Table 11. VCC Tolerances for the Low Voltage Mobile Intel Celeron Processor in the Deep Sleep State: VID = 1.15V ................................................................................. 27 Table 12. AGTL Signal Group DC Specifications ............................................................. 28 Table 13. AGTL Bus DC Specifications............................................................................ 28 Table 14. CLKREF, APIC, TAP, CMOS, and Open-drain Signal Group DC Specifications ................................................................................................... 29 Table 15. System Bus Clock AC Specifications ............................................................... 30 Table 16. Valid Mobile Intel Celeron Processor Frequencies........................................... 30 Table 17. AGTL Signal Groups AC Specifications ........................................................... 31 Table 18. CMOS and Open-drain Signal Groups AC Specifications................................ 31 Table 19. Reset Configuration AC Specifications and Power On/Power Down Timings . 32 Table 20. APIC Bus Signal AC Specifications .................................................................. 32 Table 21. TAP Signal AC Specifications........................................................................... 33 Table 22. Quick Start/Deep Sleep AC Specifications ....................................................... 33 Table 23. BCLK DC Specifications and AC Signal Quality Specifications ....................... 42 Table 24. PICCLK DC Specifications and AC Signal Quality Specifications.................... 43 Table 25. 100-MHz AGTL Signal Group Overshoot/Undershoot Tolerance at the Processor Core................................................................................................. 45 Table 26. Non-AGTL Signal Group Overshoot/Undershoot Tolerance at the Processor Core .................................................................................................................. 45 Table 27. Micro-FCBGA Package Mechanical Specifications.......................................... 47 Table 28. Signal Listing in Order by Pin/Ball Number ...................................................... 52 Table 29. Signal Listing in Order by Signal Name ............................................................ 55 Table 30. Voltage and No-Connect Pin/Ball Locations..................................................... 57 Table 31. Power Specifications for Mobile Intel Celeron Processor ................................. 58 Table 32. Thermal Diode Interface ................................................................................... 59 Table 33. Thermal Diode Specifications ........................................................................... 59 Table 34. BSEL[1:0] Encoding.......................................................................................... 63 Table 35. Input Signals ..................................................................................................... 71 Table 36. Output Signals .................................................................................................. 71 Table 37. Input/Output Signals (Single Driver) ................................................................. 72 Table 38. Input/Output Signals (Multiple Driver)............................................................... 72 Table 39. PLL Filter Inductor Recommendations ............................................................. 74 Table 40. PLL Filter Capacitor Recommendations ........................................................... 74 Table 41. PLL Filter Resistor Recommendations ............................................................. 75 6 Datasheet 298517-001 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet Revision History 298517-001 Date Revision October 2001 298517-001 Updates Initial release Datasheet 7 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet Low Voltage Mobile Intel(R) Celeron(R) Processor (0.13) in Micro-FCBGA Package Product Features ! ! ! ! Low Voltage Mobile Intel Celeron Processor (0.13) with the following Processor core/bus speeds: 650/100 MHz at 1.15V Supports the Intel Architecture with Dynamic Execution On-die primary 16-Kbyte instruction cache and 16-Kbyte write-back data cache On-die second level cache (256-Kbyte) with Advanced Transfer Cache Architecture ! ! ! ! ! ! ! 8 Datasheet Data Prefetch Logic Integrated AGTL termination Integrated math co-processor Micro-FCBGA packaging technologies Supports thin form factor notebook designs Exposed die enables more efficient heat dissipation Fully compatible with previous Intel microprocessors Binary compatible with all applications Support for MMXTM technology Support for Streaming SIMD Extensions Power Management Features Quick Start and Deep Sleep modes provide low power dissipation On-die thermal diode 298517-001 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet 1. Introduction Using Intel's advanced 0.13-micron process technology with copper interconnect, the Mobile Intel(R) Celeron(R) Processor offers high-performance and low-power consumption. The Mobile Intel Celeron Processor (0.13) in Micro-FCBGA package (hereafter referred to as "the Mobile Intel Celeron Processor") is based on the same core as existing mobile Intel(R) Pentium(R) III-M processors. Key performance features include Internet Streaming SIMD instructions, an Advanced Transfer Cache architecture, and a processor system bus speed of 100 MHz. These features are offered in MicroFCBGA package for surface mount boards. All of these technologies make outstanding performance possible for mobile PCs in a variety of shapes and sizes. The 256-KB integrated L2 cache based on the Advanced Transfer Cache architecture runs at full speed and is designed to help improve performance. It complements the system bus by providing critical data faster and reducing total system power consumption. The processor also features Data Prefetch Logic that speculatively fetches data to the L2 cache, resulting in improved performance. The Mobile Intel Celeron processor's 64-bit wide Assisted Gunning Transceiver Logic (AGTL) system bus provides a glue-less, point-to-point interface for a memory controller hub. This document covers the electrical, mechanical, and thermal specifications for the following: 1.1 298517-001 * The Low Voltage Mobile Intel Celeron Processor at the following frequency and voltage: 650 MHz at 1.15V. * Unless explicitly stated, all references to the Mobile Intel Celeron Processor (0.13) in MicroFCBGA package in this document also apply to the Low Voltage Mobile Intel Celeron Processor (0.13) in the Micro-FCBGA package. Overview * Performance features -- Supports the Intel Architecture with Dynamic Execution -- Supports the Intel Architecture MMXTM technology -- Supports Streaming SIMD Extensions for enhanced video, sound, and 3D performance -- Integrated Intel Floating Point Unit compatible with the IEEE 754 standard -- Data Prefetch Logic * On-die primary (L1) instruction and data caches -- 4-way set associative, 32-byte line size, 1 line per sector -- 16-Kbyte instruction cache and 16-Kbyte write-back data cache -- Cacheable range controlled by processor programmable registers * On-die second level (L2) cache -- 8-way set associative, 32-byte line size, 1 line per sector -- Operates at full core speed -- 256-Kbyte ECC protected cache data array * AGTL system bus interface -- 64-bit data bus, 100-MHz operation -- Uniprocessor, two loads only (processor and chipset) Datasheet 9 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet -- Integrated termination 1.2 10 * Processor clock control -- Quick Start for low power, low exit latency clock "throttling" -- Deep Sleep mode for lower power dissipation * Thermal diode for measuring processor temperature Terminology Term Definition # A "#" symbol following a signal name indicates that the signal is active low. This means that when the signal is asserted (based on the name of the signal) it is in an electrical low state. Otherwise, signals are driven in an electrical high state when they are asserted. In state machine diagrams, a signal name in a condition indicates the condition of that signal being asserted ! Indicates the condition of that signal not being asserted. For example, the condition "!STPCLK# and HS" is equivalent to "the active low signal STPCLK# is unasserted (i.e., it is at 1.5V) and the HS condition is true." L Electrical low signal levels H Electrical high signal levels 0 Logical low. For example, BD[3:0] = "1010" = "HLHL" refers to a hexadecimal "A," and D[3:0]# = "1010" = "LHLH" also refers to a hexadecimal "A." 1 Logical high. For example, BD[3:0] = "1010" = "HLHL" refers to a hexadecimal "A," and D[3:0]# = "1010" = "LHLH" also refers to a hexadecimal "A." TBD Specifications that are yet to be determined and will be updated in future revisions of the document. X Don't care condition Datasheet 298517-001 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet 1.3 298517-001 References * P6 Family of Processors Hardware Developer's Manual (Order Number 244001) * Intel(R) Architecture Software Developer's Manual -- Volume I: Basic Architecture (Order Number 245470) -- Volume II: Instruction Set Reference (Order Number 245471) -- Volume III: System Programming Guide (Order Number 245472) * CK-408(CK-Titan) Clock Synthesizer/Driver Specification (Contact your Intel Field Sales Representative) * Mobile Intel(R) Pentium(R) III Processor-M I/O Buffer Models, IBIS Format (Contact your Intel Field Sales Representative) * Mobile Intel(R) Pentium(R) III Processor-M / 440MX Platform Design Guide (Contact your Intel Field Sales Representative) * Intel Processor Identification and the CPUID Instruction Application Note AP-485 (Order Number 241618-009) Datasheet 11 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet 2. Mobile Intel Celeron Processor Features 2.1 New Features in the Mobile Intel Celeron Processor 2.1.1 256K On-die Integrated L2 Cache The 256K on die integrated L2 cache on the Mobile Intel Celeron Processor is double the L2 cache size on the Mobile Intel Celeron Processor (0.18). The L2 cache runs at the processor core speed and the increased cache size provides superior processing power. 2.1.2 Data Prefetch Logic The Mobile Intel Celeron Processor features Data Prefetch Logic that speculatively fetches data to the L2 cache before an L1 cache request occurs. This reduces transactions between the cache and system memory reducing or eliminating bus cycle penalties, resulting in improved performance. The processor also includes extensions to memory order and reorder buffers that boost performance. 12 Datasheet 298517-001 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet 2.1.3 Signal Differences Between the Mobile Intel Celeron Processor (0.18u) (in BGA2 and Micro-PGA2 Packages) and the Mobile Intel Celeron Processor (0.13 ) (in Micro-FCBGA Package) A list of new and changed signals is shown in Table 1. Table 1. New and Revised Mobile Intel Celeron Processor (0.13 ) Signals Signals BSEL[1:0] Function Signals are output only instead of I/O. Please refer to the Appendix for details. DPSLP# Deep Sleep pin (replaces SLP# pin on the mobile Celeron processor (0.18u)) NCTRL AGTL output buffer pull down impedance control. VID[4:0] Voltage Identification (different implementation from mobile Celeron processor (0.18u). Please refer to Section 3.2.3 for details. VTTPWRGD Power Good signal for VCCT, which indicates that, the VID signals are stable. Please refer to Figure 3 for VTTPWRGD System-Level Connections. 2.2 Power Management 2.2.1 Clock Control Architecture The Mobile Intel Celeron Processor clock control architecture (Figure 1) has been optimized for leading edge mobile computer designs. The clock control architecture consists of six different clock states: Normal, Auto Halt, Quick Start, HALT/Grant Snoop and Deep Sleep states. The Auto Halt state provides a low-power clock state that can be controlled through the software execution of the HLT instruction. The Quick Start state provides a very low power and low exit latency clock state that can be used for hardware controlled "idle" computer states. The Deep Sleep state provides extremely lowpower states that can be used for "Power-On-Suspend" computer states, which is an alternative to shutting off the processor's power. The exit latency of the Deep Sleep state is 30 msec in the Mobile Intel Celeron Processor. Performing state transitions not shown in Figure 1 is neither recommended nor supported. Figure 2 provides the clock state characteristics, which are described in detail in the following sections. 2.2.2 Normal State The Normal state of the processor is the normal operating mode where the processor's core clock is running and the processor is actively executing instructions. 2.2.3 Auto Halt State This is a low-power mode entered by the processor through the execution of the HLT instruction. A transition to the Normal state is made by a halt break event (one of the following signals going active: NMI, INTR, BINIT#, INIT#, RESET#, FLUSH#, or SMI#). 298517-001 Datasheet 13 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet Asserting the STPCLK# signal while in the Auto Halt state will cause the processor to transition to the Quick Start state. Deasserting STPCLK# will cause the processor to return to the Auto Halt state without issuing a new Halt bus cycle. The SMI# interrupt is recognized in the Auto Halt state. The return from the System Management Interrupt (SMI) handler can be to either the Normal state or the Auto Halt state. See the Intel(R) Architecture Software Developer's Manual, Volume III: System Programmer's Guide for more information. No Halt bus cycle is issued when returning to the Auto Halt state from the System Management Mode (SMM). The FLUSH# signal is serviced in the Auto Halt state. After the on-chip and off-chip caches have been flushed, the processor will return to the Auto Halt state without issuing a Halt bus cycle. Transitions in the A20M# and PREQ# signals are recognized while in the Auto Halt state. Figure 1. Clock Control States BCLK stopped or DPSLP# STPCLK#1 Normal HS=false halt break (!STPCLK# and !HS) or RESET# BCLK on and !DPSLP# STPCLK#1 HLT instruction1 Auto Halt HS=true Deep Sleep 2 Quick Start !STPCLK# and HS snoop occurs snoop serviced snoop occurs HALT/Grant Snoop snoop serviced V0001-022 NOTES: 1. State transition does not occur until the Stop Grant or Auto Halt acknowledge bus cycle completes Halt break - A20M#, BINIT#, FLUSH#, INIT#, INTR, NMI, PREQ#, RESET#, SMI#, or APIC interrupt HLT - HLT instruction executed HS - Processor Halt State 2. Restrictions apply to the use of both methods of entering Deep Sleep. See Deep Sleep state description for details. 2.2.4 Quick Start State The processor is required to be configured for the Quick Start state by strapping the A15# signal low. In the Quick Start state the processor is only capable of acting on snoop transactions generated by the system bus priority device. Because of its snooping behavior, Quick Start can only be used in a uniprocessor (UP) configuration. 14 Datasheet 298517-001 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet A transition to the Deep Sleep state can be made by stopping the clock input to the processor or asserting the DPSLP# signal. A transition back to the Normal state (from the Quick Start state) is made only if the STPCLK# signal is deasserted. While in this state the processor is limited in its ability to respond to input. It is incapable of latching any interrupts, servicing snoop transactions from symmetric bus masters, or responding to FLUSH# or BINIT# assertions. While the processor is in the Quick Start state, it will not respond properly to any input signal other than STPCLK#, RESET#, or BPRI#. If any other input signal changes, then the behavior of the processor will be unpredictable. No serial interrupt messages may begin or be in progress while the processor is in the Quick Start state. RESET# assertion will cause the processor to immediately initialize itself, but the processor will stay in the Quick Start state after initialization until STPCLK# is deasserted. 2.2.5 HALT/Grant Snoop State The processor will respond to snoop transactions on the system bus while in the Auto Halt or Quick Start state. When a snoop transaction is presented on the system bus the processor will enter the HALT/Grant Snoop state. The processor will remain in this state until the snoop has been serviced and the system bus is quiet. After the snoop has been serviced, the processor will return to its previous state. If the HALT/Grant Snoop state is entered from the Quick Start state, then the input signal restrictions of the Quick Start state still apply in the HALT/Grant Snoop state, except for those signal transitions that are required to perform the snoop. 2.2.6 Deep Sleep State The Deep Sleep state is a very low power state that the processor can enter while maintaining its context. The Deep Sleep state is entered by stopping the BCLK input to the processor or by asserting the DPSLP# signal, while it is in the Quick Start state. Note that either one of the methods can be used to enter Deep Sleep but not both at the same time. When BCLK is stopped, it must obey the DC levels specified in Table 23. The processor will return to the Quick Start state from the Deep Sleep state when the BCLK input is restarted or the DPSLP# signal is deasserted. Due to the PLL lock latency, there is a delay of up to 30 sec after the clocks have started before this state transition happens. PICCLK may be removed in the Deep Sleep state. PICCLK should be designed to turn on when BCLK turns on or DPSLP# is deasserted when transitioning out of the Deep Sleep state. 298517-001 Datasheet 15 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet Table 2. Clock State Characteristics Clock State Exit Latency Snooping? System Uses Normal N/A Yes Normal program execution Auto Halt 10 sec Yes S/W controlled entry idle mode Quick Start Through snoop, to HALT/Grant Snoop state: immediate Yes H/W controlled entry/exit mobile throttling Through STPCLK#, to Normal state: 10 sec 2.2.7 HALT/Grant Snoop A few bus clocks after snoop completion Yes Supports snooping in the low power states Deep Sleep 30 sec No H/W controlled entry/exit mobile powered-on suspend support Operating System Implications of Low-power States The time-stamp counter and the performance monitor counters are not guaranteed to count in the Quick Start state. The local APIC timer and performance monitor counter interrupts should be disabled before entering the Deep Sleep state or the resulting behavior will be unpredictable. 2.3 AGTL Signals The Mobile Intel Celeron Processor system bus signals use a variation of the low-voltage swing GTL signaling technology. The AGTL system bus depends on incident wave switching and uses flight time for timing calculations of the AGTL signals, as opposed to capacitive derating. Intel recommends analog signal simulation of the system bus including trace lengths. Contact your field sales representative to receive the IBIS models for the Mobile Intel Celeron Processor (these are the same models as the Mobile Pentium III Processor-M). The AGTL system bus of the Mobile Intel Celeron Processor is designed to support high-speed data transfers with multiple loads on a long bus that behaves like a transmission line. However, in mobile systems the system bus only has two loads (the processor and the chipset) and the bus traces are short. It is possible to change the layout and termination of the system bus to take advantage of the mobile environment using the same AGTL I/O buffers. This termination is provided on the processor core (except for the RESET# signal). 2.4 Mobile Intel Celeron Processor CPUID When the CPUID version information is loaded with EAX=01H, the EAX and EBX registers contain the values shown in Table 3. After a power-on RESET, the EDX register contains the processor version information (type, family, model, stepping). Table 4 shows the CPUID Cache and TLB descriptor values after the L2 cache is initialized. See Intel(R) Processor Identification and the CPUID Instruction Application Note AP-485 for further information. 16 Datasheet 298517-001 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet Table 3. Mobile Intel Celeron Processor CPUID EAX[31:0] EBX[7:0] Reserved [31:14] Type [13:12] Family [11:8] Model [7:4] Stepping [3:0] X 6 B X 0 Brand ID 03 Table 4. Mobile Intel Celeron Processor CPUID Cache and TLB Descriptors Cache and TLB Descriptors 298517-001 01H, 02H, 03H, 04H, 08H, 0CH, 83H Datasheet 17 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet 3. Electrical Specifications 3.1 Processor System Signals Table 5 lists the processor system signals by type. All AGTL signals are synchronous with the BCLK signal. All TAP signals are synchronous with the TCK signal except TRST#. All CMOS input signals can be applied asynchronously. Table 5. System Signal Groups Group Name Signals AGTL Input BPRI#, DEFER#, RESET#, RSP# AGTL Output PRDY# AGTL I/O A[35:3]#, ADS#, AERR#, AP[1:0]#, BERR#, BINIT#, BNR#, BP[3:2]#, BPM[1:0]#, BREQ0#, D[63:0]#, DBSY#, DEP[7:0]#, DRDY#, HIT#, HITM#, LOCK#, REQ[4:0]#, RP#, RS[2:0]#, TRDY# 1.5V CMOS Input A20M#, DPSLP#, FLUSH#, IGNNE#, INIT#, LINT0/INTR, LINT1/NMI, PREQ#, SMI#, STPCLK# 1.8V CMOS Input PWRGOOD 1.5V Open Drain Output FERR#, IERR# 3.3V Open Drain Output BSEL[1:0], VID[4:0] 1.25V input VTTPWRGD 2.5V Clock Input BCLK APIC Clock PICCLK APIC I/O PICD[1:0] Thermal Diode THERMDC, THERMDA TAP Input TCK, TDI, TMS, TRST# TAP Output TDO Power/Other CLKREF, CMOSREF, EDGECTRLP, NC, NCTRL, PLL1, PLL2, RTTIMPEDP, VCC, VCCT, VREF, VSS, NOTES: 1. VCC is the power supply for the core logic. 2. PLL1 and PLL2 are power/ground for the PLL analog section. See Section 3.2.2 for details. 3. VCCT is the power supply for the system bus buffers. 4. VREF is the voltage reference for the AGTL input buffers. 5. VSS is system ground. The APIC data and TAP outputs are Open-drain and should be pulled up to 1.5V using resistors with the values shown in Table 6. If Open-drain drivers are used for input signals, then they should also be pulled up to the appropriate voltage using resistors with the values shown in Table 6. 18 Datasheet 298517-001 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet Table 6. Recommended Resistors for Mobile Intel Celeron Processor Signals Recommended Resistor Value ( ) Mobile Intel Celeron Processor Signal 10 pull-down BREQ0#3 14 pull-up NCTRL 39 pull-up TMS 39 pull-down TCK 56.2 pull-up PRDY#, RESET#4 56.2 pull-down RTTIMPEDP 110 pull-down EDGECTRLP 150 pull-up PICD[1:0], TDO 200-300 pull-up PREQ#, TDI 500 pull-down TRST# 1K pull-up BSEL[1:0], TESTHI, VID[4:0], VTTPWRGD 1K pull-down TESTLO 1.5k pull-up FERR#, IERR#, PWRGOOD 3K pull-up FLUSH# 1, 2 Additional Pullup/Pulldown Resistor Recommendations5 270 pull-up SMI# 680 pull-up STPCLK# 1.5k pull-up A20M#, DPSLP#, INIT#, IGNNE#, LINT0/INTR, LINT1/NMI NOTES: 1. The recommendations above are only for signals that are being used. These recommendations are maximum values only; stronger pull-ups may be used. Pull-ups for the signals driven by the chipset should not violate the chipset specification. Refer to Section 3.1.4 for the required pull-up or pull-down resistors for signals that are not being used. 2. Open-drain signals must never violate the undershoot specification in Section 4.3. Use stronger pull-ups if there is too much undershoot. 3. A pull-down on BREQ0# is an alternative to having the central agent to drive BREQ0# low at reset. 4. A 56.2 1% terminating resistor connected to VCCT is required. 5. These pull up recommendations apply to systems on which these signals are not actively pulled high such as those utilizing the 82443MX chipset. 3.1.1 Power Sequencing Requirements Unlike the Mobile Intel Celeron Processor (0.18), the Mobile Intel Celeron Processor (0.13) does have specific power sequencing requirements. The power on sequencing and timings are shown in Figure 10 and Table 19. Power down timing requirements are shown in Figure 11, Figure 12, and Table 19. The VCC power plane must not rise too fast. At least 200 sec (TR) must pass from the time that VCC is at 10% of its nominal value until the time that VCC is at 90% of its nominal value. For more details, Contact your Intel Field Sales Representative. 3.1.2 Test Access Port (TAP) Connection The TAP interface is an implementation of the IEEE 1149.1 ("JTAG") standard. Due to the voltage levels supported by the TAP interface, Intel recommends that the Mobile Intel Celeron Processor and the other 1.5-V JTAG specification compliant devices be last in the JTAG chain after any devices with 3.3-V or 5.0-V JTAG interfaces within the system. A translation buffer should be used to reduce the 298517-001 Datasheet 19 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet TDO output voltage of the last 3.3/5.0V device down to the 1.5V range that the Mobile Intel Celeron Processor can tolerate. Multiple copies of TMS and TRST# must be provided, one for each voltage level. A Debug Port and connector may be placed at the start and end of the JTAG chain containing the processor, with TDI to the first component coming from the Debug Port and TDO from the last component going to the Debug Port. There are no requirements for placing the Mobile Intel Celeron Processor in the JTAG chain, except for those that are dictated by voltage requirements of the TAP signals. 3.1.3 Catastrophic Thermal Protection The Mobile Intel Celeron Processor does not support catastrophic thermal protection or the THERMTRIP# signal. An external thermal sensor must be used to protect the processor and the system against excessive temperatures. If the external thermal sensor detects a processor junction temperature of 101 C (maximum), both the VCC and VCCT supplies to the processor must be reduced to at least 50% of the nominal values within 500 ms and recommended to be turned off completely within 1s to prevent damage to the processor. Processor temperature must be monitored in all states including low power states. 3.1.4 Unused Signals All signals named NC must be unconnected. Unused AGTL inputs, outputs and bi-directional signals should be unconnected. Unused CMOS active low inputs should be connected to 1.5V and unused active high inputs should be connected to VSS. Unused Open-drain outputs should be unconnected. When tying any signal to power or ground, a resistor will allow for system testability. For unused signals, Intel suggests that 1.5-k resistors are used for pull-ups and 1.0-k resistors are used for pull-downs. PICCLK must be driven with a clock that meets specification and the PICD[1:0] signals must be pulled up separately to 1.5V with 150- resistors, even if the local APIC is not used. If the TAP signals are not used then the inputs should be pulled to ground with 1-k resistors and TDO should be left unconnected. 3.1.5 Signal State in Low-power States 3.1.5.1 System Bus Signals All of the system bus signals have AGTL input, output, or input/output drivers. Except when servicing snoops, the system bus signals are tri-stated and pulled up by the termination resistors. Snoops are not permitted in the Deep Sleep state. 3.1.5.2 CMOS and Open-drain Signals The CMOS input signals are allowed to be in either the logic high or low state when the processor is in a low-power state. In the Auto Halt state these signals are allowed to toggle. These input buffers have no internal pull-up or pull-down resistors and system logic can use CMOS or Open-drain drivers to drive them. The Open-drain output signals have open drain drivers and external pull-up resistors are required. One of the two output signals (IERR#) is a catastrophic error indicator and is tri-stated (and pulled-up) when the 20 Datasheet 298517-001 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet processor is functioning normally. The FERR# output can be either tri-stated or driven to VSS when the processor is in a low-power state depending on the condition of the floating-point unit. Since this signal is a DC current path when it is driven to VSS, Intel recommends that the software clears or masks any floating-point error condition before putting the processor into the Deep Sleep state. 3.1.5.3 Other Signals The system bus clock (BCLK) must be driven in all of the low-power states except the Deep Sleep state. The APIC clock (PICCLK) must be driven whenever BCLK is driven. Otherwise, it is permitted to turn off PICCLK by holding it at VSS. BCLK should obey the DC levels in Table 23. In the Auto Halt state, the APIC bus data signals (PICD[1:0]) may toggle due to APIC bus messages. These signals are required to be tri-stated and pulled-up when the processor is in the Quick Start or Deep Sleep states. 3.2 Power Supply Requirements 3.2.1 Decoupling Guidelines The Mobile Intel Celeron Processor in Micro-FCBGA package has six 0.68-F capacitors on VCC and two 0.68-F capacitors on VCCT. In addition to the package capacitors, sufficient board level capacitors are also necessary for power supply decoupling. These guidelines are as follows: * High and Mid Frequency VCC decoupling - Place twenty-four 0.22-F 0603 capacitors directly under the package on the solder side of the motherboard using at least two vias per capacitor node. Ten 10-F X7 6.3V 1206-size ceramic capacitors should be placed around the package periphery near the balls. Trace lengths to the vias should be designed to minimize inductance. Avoid bending traces to minimize ESL. * High and Mid Frequency VCCT decoupling - Place ten 1-F X7R 0603 ceramic capacitors close to the package. Via and trace guidelines are the same as above. * Bulk VCC decoupling - Minimum of 1200 F capacitance with Equivalent Series Resistance (ESR) less than or equal to 3.5 m. * Bulk VCCT decoupling - Platform dependent but recommendation is minimum of 660 F with ESR less than or equal to 7 m. Please refer to the appropriate platform design guidelines for bulk decoupling recommendations. 3.2.2 Voltage Planes All VCC and VSS pins/balls must be connected to the appropriate voltage plane. All VCCT and VREF pins/balls must be connected to the appropriate traces on the system electronics. In addition to the main VCC, VCCT, and VSS power supply signals, PLL1 and PLL2 provide analog decoupling to the PLL section. PLL1 and PLL2 should be connected according to Figure 2. Do not connect PLL2 directly to VSS. Appendix A contains the RLC filter specification. 298517-001 Datasheet 21 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet Figure 2. PLL RLC Filter L1 R1 PLL1 VCCT C1 PLL2 3.2.3 V0027-01 Voltage Identification There are five voltage identification balls/pins on the Mobile Intel Celeron Processor. These signals can be used to support automatic selection of VCC voltages. They are needed to cleanly support voltage specification variations on current and future processors. VID[4:0] are defined in Table 7. The voltages specified in the VID table are the Battery Optimized Mode VCC voltages. The VID[4:0] signals are open drain on the processor and need pullup resistors to 3.3V on the motherboard. Please refer to the mobile VR guidelines provided by Intel for additional information. Table 7. Mobile Intel Celeron Processor VID Values VID[4:0] VCC (V) VID[4:0] VCC (V) VID[4:0] VCC (V) VID[4:0] VCC (V) 00000 1.750 01000 1.350 10000 0.975 11000 0.775 00001 1.700 01001 1.300 10001 0.950 11001 0.750 00010 1.650 01010 1.250 10010 0.925 11010 0.725 00011 1.600 01011 1.200 10011 0.900 11011 0.700 00100 1.550 01100 1.150 10100 0.875 11100 0.675 00101 1.500 01101 1.100 10101 0.850 11101 0.650 00110 1.450 01110 1.050 10110 0.825 11110 0.625 00111 1.400 01111 1.000 10111 0.800 11111 0.600 Figure 3 shows the system level connections for the VTTPWRGD signal. Please refer to the appropriate VR and system level guidelines provided by Intel for more details. 22 Datasheet 298517-001 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet Figure 3. VTTPWRGD System-Level Connections Vcct Vcct Processor Voltage Regulator 1k Vcct Vttpwrgd (output) 3.3V 100k Vttpwrgd (input) 10k Clock Generator Vttpwrgd# (input) 1.2V to 3.3V Level Shifter 3.3 System Bus Clock and Processor Clocking The BCLK clock input directly controls the operating speed of the system bus interface. All system bus timing parameters are specified with respect to the rising edge of the BCLK input. The Mobile Intel Celeron Processor core frequency is a multiple of the BCLK frequency. The processor core frequency is configured during manufacturing. The configured bus ratio is visible to software in the Power-on configuration register. See Section 7.2 for details. Multiplying the bus clock frequency is necessary to increase performance while allowing for easier distribution of signals within the system. Clock multiplication within the processor is provided by the internal Phase Lock Loop (PLL), which requires a constant frequency BCLK, input. During Reset or on exit from the Deep Sleep state, the PLL requires some amount of time to acquire the phase of BCLK. This time is called the PLL lock latency, which is specified in Section 3.6, AC timing parameters T18 and T47. 3.4 Maximum Ratings Table 8 contains the Mobile Intel Celeron Processor stress ratings. Functional operation at the absolute maximum and minimum is neither implied nor guaranteed. The processor should not receive a clock while subjected to these conditions. Functional operating conditions are provided in the AC and DC tables. Extended exposure to the maximum ratings may affect device reliability. Furthermore, although the processor contains protective circuitry to resist damage from static electric discharge, one should always take precautions to avoid high static voltages or electric fields. 298517-001 Datasheet 23 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet Table 8. Mobile Intel Celeron Processor Absolute Maximum Ratings Symbol Parameter Min Max Unit Notes TStorage Storage Temperature -40 85 C Note 1 VCC(Abs) Supply Voltage with respect to VSS -0.5 1.75 V VCCT System Bus Buffer Voltage with respect to VSS -0.3 1.75 V VIN GTL System Bus Buffer DC Input Voltage with respect to VSS -0.3 1.75 V Notes 2, 3 VIN125 1.25V Buffer DC Input Voltage with respect to VSS -0.3 1.75 V Note 4 VIN15 1.5V Buffer DC Input Voltage with respect to VSS -0.3 2.0 V Note 5 VIN18 1.8V Buffer DC Input Voltage with respect to VSS -0.3 2.0 V Note 6 VIN20 2.0V Buffer DC Input Voltage with respect to VSS -0.3 2.4 V Note 7 VIN25 2.5V Buffer DC Input Voltage with respect to VSS -0.3 3.3 V Note 9 VINVID VID ball/pin DC Input Voltage with respect to VSS -- 3.465 V Note 8 IVID VID Current -0.3 3.6 mA Note 8 NOTES: 1. The shipping container is only rated for 65C. 2. 3. 4. 5. 6. 7. 8. 9. 3.5 Parameter applies to the AGTL signal groups only. Compliance with both VIN GTL specifications is required. The voltage on the AGTL signals must never be below -0.3 or above 1.75V with respect to ground. Parameter applies to CLKREF, TESTHI, VTTPWRGD signals. Parameter applies to CMOS, Open-drain, APIC, TESTLO and TAP bus signal groups only. Parameter applies to PWRGOOD signal. Parameter applies to PICCLK signal. Parameter applies to each VID pin/ball individually. Parameter applies to BCLK signal in Single Ended Clocking Mode. DC Specifications Table 9 through Table 14 list the DC specifications for the Mobile Intel Celeron Processor. Specifications are valid only while meeting specifications for the junction temperature, clock frequency, and input voltages. The junction temperature range for all DC specifications is 0C to 100C. Care should be taken to read all notes associated with each parameter. Unlike the mobile Intel Pentium III processor, the Vcc tolerances for the Mobile Intel Celeron Processor are not specified as a percentage of nominal. The tolerances are instead specified in the form of load lines for the static and transient cases in Table 10 and Table 11. Illustration of the load lines is shown in Figure 4 and Figure 5. 24 Datasheet 298517-001 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet 1 Table 9. Power Specifications for Mobile Intel Celeron Processor Symbol VCC VCC,DC Parameter Min Typ Max Unit Notes Transient VCC for core logic 1.15 V Notes 10, 11 1.15 V Notes 10, 11 Static VCC for core logic VCCT VCC for System Bus Buffers, Transient tolerance 1.138 1.25 1.362 V 9%, Notes 8,11 VCCT,DC VCC for System Bus Buffers, Static tolerance 1.188 1.25 1.312 V 5%, Notes 2,11 ICC Current for VCC at core frequency 650 MHz & 1.15V A Note 4 A Notes 3, 4 A Note 4 A Note 4 A Note 4 Note 9 10.52 ICCT Current for VCCT 2.7 ICC,AH Processor Auto Halt current at 1.15V 5.42 Processor Quick Start current at 1.15V 5.16 Processor Deep Sleep Leakage current at 1.15V 4.79 ILVID VID leakage current 0.5 mA dICC/dt VCC power supply current slew rate 400 A/s Notes 6, 7 ICC,QS ICC,DSLP NOTES: 1. Unless otherwise noted, all specifications in this table apply to all processor frequencies. Processors will comply with the ICCx,max specification for the current mode of operation. 2. Static voltage regulation includes: DC output initial voltage set point adjust, output ripple and noise, temperature and warm up. 3. ICCT is the current supply for the system bus buffers, including the on-die termination. 4. ICCx,max specifications are specified at VCC static (typical) derived from the tolerances in Table 10 through Table 15, VCCT,max, Tjmax, and under maximum signal loading conditions. 5. Maximum ICC,DPRSLP specified at VCC = 0.85V. 6. Based on simulations and averaged over the duration of any change in current. Use to compute the maximum inductance and reaction time of the voltage regulator. This parameter is not tested. 7. Maximum values specified by design/characterization at nominal VCC and VCCT. 8. VCCx must be within this range under all operating conditions, including maximum current transients. VCCx must return to within the static voltage specification, VCCx,DC, within 100 s after a transient event. 9. VID leakage current is < 100 uA for VID voltages under 3.0V. 10. Typical VCC indicates the VID encoded voltage. Voltage supplied must conform to the load line specification shown in Table 10 through Table 13. 11. Voltages are measured at the package ball on the Micro-FCBGA part. 298517-001 Datasheet 25 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet Figure 4. Illustration of VCC Static and Transient Tolerances (VID = 1.15V) 1.250 Transient Maximum Static Maximum 1.200 Static Typical 1.150 V C C 1.100 Static Minimum 1.050 Transient Minimum 1.000 0.950 0.0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 11.0 12.0 13.0 14.0 15.0 ICC Figure 5. Illustration of Deep Sleep VCC Static and Transient Tolerances (VID Setting = 1.15V) 1.180 Transient Maximum Static Maximum 1.160 Static Typical 1.140 1.120 1.100 V C 1.080 C 1.060 Static Minimum 1.040 1.020 Transient Minimum 1.000 0.980 0 1 2 3 4 5 6 ICC 26 Datasheet 298517-001 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet Table 10. VCC Tolerances for the Low Voltage Mobile Intel Celeron Processor: VID = 1.15V ICC (A) VCC (V) Static Transient Typ Min Max Min Max 0.0 1.150 1.125 1.175 1.105 1.195 1.0 1.146 1.121 1.171 1.101 1.191 2.0 1.142 1.117 1.167 1.097 1.187 3.0 1.138 1.113 1.163 1.093 1.183 4.0 1.134 1.109 1.159 1.089 1.179 5.0 1.130 1.105 1.155 1.085 1.175 6.0 1.126 1.101 1.151 1.081 1.171 7.0 1.122 1.097 1.147 1.077 1.167 8.0 1.118 1.093 1.143 1.073 1.163 9.0 1.114 1.089 1.139 1.069 1.159 10.0 1.110 1.085 1.135 1.065 1.155 11.0 1.106 1.081 1.131 1.061 1.151 12.0 1.102 1.077 1.127 1.057 1.147 13.0 1.098 1.073 1.123 1.053 1.143 14.0 1.094 1.069 1.119 1.049 1.139 15.0 1.090 1.065 1.115 1.045 1.135 Table 11. VCC Tolerances for the Low Voltage Mobile Intel Celeron Processor in the Deep Sleep State: VID = 1.15V ICC (A) VCC (V) Static Typ Min Max Min Max 1.114 1.089 1.139 1.069 1.159 1.0 1.110 1.085 1.135 1.065 1.155 2.0 1.106 1.081 1.131 1.061 1.151 3.0 1.102 1.077 1.127 1.057 1.147 4.0 1.098 1.073 1.123 1.053 1.143 5.0 1.094 1.069 1.119 1.049 1.139 6.0 1.090 1.065 1.115 1.045 1.135 0.0 298517-001 Transient Datasheet 27 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet Table 12. AGTL Signal Group DC Specifications Symbol Parameter Min Max VREF-0.2 Unit Notes VIL Input Low Voltage -0.15 V VIH Input High Voltage VREF+0.2 VCCT V See VCCT,max in Table 17 VOH Output High Voltage -- -- V See VCCT,max in Table 17 RON Output Low Drive Strength 16.67 Note 2 IL Leakage Current for Inputs, Outputs and I/Os 100 A Note 1 NOTES: 1. Specification applies to leakage high only, for pins with on die RTT, (0 < VIN/OUT VCCT). 2. Refer to IBIS models for I/V characteristics. Table 13. AGTL Bus DC Specifications Symbol VCCT Parameter Min Bus Termination Voltage Typ Max 1.25 VREF Input Reference Voltage 2 RTT Bus Termination Strength 50 /3VCCT - 2% V 2 2 56 65 /3VCCT Unit /3VCCT + 2% V Notes Note 1 2%, Note 2 On-die RTT, Note 3 NOTES: 1. Please refer to Table 9 for minimum and maximum values. 28 2. VREF should be created from VCCT by a voltage divider. 3. The RESET# signal does not have an on-die RTT. It requires an off-die 56.2 1% terminating resistor connected to VCCT. Datasheet 298517-001 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet Table 14. CLKREF, APIC, TAP, CMOS, and Open-drain Signal Group DC Specifications Symbol Parameter Min Max Unit Notes VIL15 Input Low Voltage, 1.5V CMOS -0.15 VCMOSREFmin - 300 mV V VIL18 Input Low Voltage, 1.8V CMOS -0.36 0.36 V Notes 1, 2 VIH15 Input High Voltage, 1.5V CMOS VCMOSREFmax + 2.0 250 mV V Note 10 VIH15PICD Input High Voltage, 1.5V PICD[1:0] VCMOSREFmax + 2.0 200 mV V Note 11 VIH18 Input High Voltage, 1.8V CMOS 1.44 V Notes 1, 2 VOH15 Output High Voltage, 1.5V CMOS N/A 1.615 V All outputs are Open-drain VOH33 Output High Voltage, 3.3V signals 2.0 3.465 V 3.3V + 5% VOL33 Output Low Voltage, 3.3V signals 0.8 V VOL Output Low Voltage 0.3 V 2.0 Note 8 VCMOSREF CMOSREF Voltage 0.90 1.10 V Note 4 VCLKREF CLKREF Voltage 1.187 1.312 V Note 9 VILVTTPWR Input Low Voltage, VTTPWRGD VIHVTTPWR Input High Voltage, VTTPWRGD 0.4 1.0 RON 30 IOL Output Low Current IL Leakage Current for Inputs, Outputs and I/Os 10 100 V Note 7 V Note 7 Note 3 mA Note 6 A Note 5 NOTES: 1. Parameter applies to the PWRGOOD signal only. 2. VILx,min and VIHx,max only apply when BCLK and PICCLK are stopped. PICCLK should be stopped in the low state. See Table 23 for DC levels when BCLK is stopped. 3. Measured at 9 mA. 4. VCMOSREF should be created from a stable 1.5V supply using a voltage divider. It must track the voltage supply to maintain noise immunity. The same 1.5V supply should be used to power the chipset CMOS I/O buffers that drive these signals. 5. (0 VIN/OUT VIHx,max). 6. Specified as the minimum amount of current that the output buffer must be able to sink. However, VOL,max cannot be guaranteed if this specification is exceeded. 7. Parameter applies to VTTPWRGD signal only. 8. Applies to non-AGTL signals except BCLK, PWRGOOD, PICCLK, BSEL[1:0], VID[4:0]. 9. 5% DC tolerance. CLKREF must be generated from the 2.5V supply used to generate the BCLK signal. AC Tolerance must be less than -40dB @ 1 MHz. 10. Applies to all TAP and CMOS signals (not to APIC signals). 11. Applies to PICD[1:0]. 3.6 AC Specifications 3.6.1 System Bus, Clock, APIC, TAP, CMOS, and Open-drain AC Specifications All system bus AC specifications for the AGTL signal group are relative to the rising edge of the BCLK input. All AGTL timings are referenced to VREF for both "0" and "1" logic levels unless otherwise specified. All APIC, TAP, CMOS, and Open-drain signals except PWRGOOD are referenced to 1.0V. All minimum and maximum specifications are at points within the power supply ranges shown in Tables 298517-001 Datasheet 29 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet 9-13 and junction temperatures (Tj) in the range 0C to 100C. Tj must be less than or equal to 100C for all functional processor states. Table 15. System Bus Clock AC Specifications Symbol Parameter 1 Min System Bus Frequency T1S1 BCLK Period T1S1abs BCLK Period - Instantaneous Minimum T2S1 BCLK Period Stability T3S1 BCLK High Time Typ Max Unit 100 MHz 10 ns 9.75 Figure 6 ns 250 2.70 Note 2 Note 2 ps ns Notes Notes 2, 3, 4 6 at>2.0V T4S1 BCLK Low Time 2.45 ns 6 at<0.5V T5S1 BCLK Rise Time 0.4 1.6 ns 6 Note 5 T6S1 BCLK Fall Time 0.4 1.6 ns 6 Note 5 NOTES: 1. All AC timings for AGTL and CMOS signals are referenced to the BCLK rising edge at 1.25V. 2. Period, jitter, skew and offset measured at 1.25V. 3. Not 100% tested. Specified by design/characterization. 4. Measured on the rising edge of adjacent BCLKs at 1.25V. The jitter present must be accounted for as a component of BCLK skew between devices. 5. Measured between 0.5V and 2.0V Table 16. Valid Mobile Intel Celeron Processor Frequencies BCLK Frequency (MHz) Frequency Multiplier Core Frequency (MHz) Power-on Configuration bits [27,25:22] 100 6.5 650 0, 1111 NOTE: 30 While other combinations of bus and core frequencies are defined, operation at frequencies other than those listed above will not be validated by Intel and are not guaranteed. The frequency multiplier is programmed into the processor when it is manufactured and it cannot be changed. Datasheet 298517-001 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet Table 17. AGTL Signal Groups AC Specifications 1 RTT = 56 internally terminated to VCCT; VREF = 2/3VCCT; load = 50 ohms Symbol Parameter Min T7 AGTL Output Valid Delay 0.40 T8 AGTL Input Setup Time 1.30 Max Unit 3.25 Figure ns 9 ns 10 Notes Notes 2, 3, 6 T9 AGTL Input Hold Time 1 ns 10 Note 4 T10 RESET# Pulse Width 1 ms 11,12 Note 5 NOTES: 1. All AC timings for AGTL signals are referenced to the BCLK rising edge at 1.25V. All AGTL signals are referenced at VREF. Unless other specified, all timings apply to 100-MHz bus frequency. 2. RESET# can be asserted (active) asynchronously, but must be deasserted synchronously. 3. Specification is for a minimum 0.40V swing from Vref-200 mV to Vref+200 mV. 4. Specification is for a maximum 0.8V swing from Vcct-0.8V to Vcct. 5. After VCC, VCCT, and BCLK become stable and PWRGOOD is asserted. 6. Applies to all processors supporting 100 MHz bus clock frequency. Table 18. CMOS and Open-drain Signal Groups AC Specifications Symbol Parameter Min Max 1, 2 Unit Figure Notes T14 1.5V Input Pulse Width, except PWRGOOD and LINT[1:0] 2 BCLKs 9 Active and inactive states T14B LINT[1:0] Input Pulse Width 6 BCLKs 9 Note 3 T15 PWRGOOD Inactive Pulse Width 2 s 12 Note 4, 5 NOTES: 1. All AC timings for CMOS and Open-drain signals are referenced to the rising edge of BCLK at 1.25V. All CMOS and Open-drain signals are referenced at 1.0V. 2. Minimum output pulse width on CMOS outputs is 2 BCLKs. 3. This specification only applies when the APIC is enabled and the LINT1 or LINT0 signal is configured as an edge triggered interrupt with fixed delivery, otherwise specification T14 applies. 4. When driven inactive, or after VCC, VCCT, and BCLK become stable. PWRGOOD must remain below VIL18,MAX until all the voltage planes meet the voltage tolerance specifications in Tables 9-11 and BCLK has met the AC specifications in Table 23 for at least 2 s. PWRGOOD must rise error-free and monotonically to 1.8V. 5. If the BCLK Settling Time specification (T60) can be guaranteed at power-on reset then the PWRGOOD Inactive Pulse Width specification (T15) is waived and BCLK may start after PWRGOOD is asserted. PWRGOOD must still remain below VIL18,max until all the voltage planes meet the voltage tolerance specifications. 298517-001 Datasheet 31 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet Table 19. Reset Configuration AC Specifications and Power On/Power Down Timings Symbol Parameter Min Typ Max Unit Figure BCLKs 11 Before deassertion of RESET# BCLKs 11 After clock that deasserts RESET# 1 ms 12 Before deassertion of RESET# 1 1 ms 12 T16 Reset Configuration Signals (A[15:5]#, BREQ0#, FLUSH#, INIT#, PICD0) Setup Time T17 Reset Configuration Signals (A[15:5]#, 2 BREQ0#, FLUSH#, INIT#, PICD0) Hold Time T18 RESET#/PWRGOOD Setup Time T18A VCCT to VTTPWRGD Setup Time 4 20 T18B VCC to PWRGOOD Setup Time ms 12 T18C BSEL, VID valid time before VTTPWRGD assertion 1 s 12 T18D RESET# inactive to Valid Outputs 1 BCLK 11 T18E RESET# inactive to Drive Signals 4 BCLKs 11 T19A Time from VCC(nominal)-12% to PWRGOOD low T19B All outputs valid after PWRGOOD low 0 ns 13 T19C All inputs required valid after PWRGOOD low 0 ns 13 T20A Time from VCCT-12% to VTTPWRGD low T20B All outputs valid after VTTPWRGD low 10 0 0 ns 13 ns 14 0 ns 14 T20C All inputs required valid after VTTPWRGD low 0 ns 14 T20D VID, BSEL signals valid after VTTPWRGD low ns 14 NOTE: Notes 0 VCC(nominal) is the VID voltage setting At least 1 ms must pass after PWRGOOD rises above VIH18min and BCLK meets the AC timing specification until RESET# may be deasserted. Table 20. APIC Bus Signal AC Specifications Symbol 1 Parameter T21 PICCLK Frequency T22 T23 Min Max Unit Figure 2 33.3 MHz PICCLK Period 30 500 ns 6 PICCLK High Time 10.5 ns 6 Notes Note 2 at>1.6V T24 PICCLK Low Time 10.5 ns 6 at<0.4V T25 PICCLK Rise Time 0.25 3.0 ns 6 (0.4V - 1.6V) T26 PICCLK Fall Time 0.25 3.0 ns 6 (1.6V - 0.4V) T27 PICD[1:0] Setup Time 8.0 ns 9 Note 3 T28 PICD[1:0] Hold Time 2.5 ns 9 Note 3 T29 PICD[1:0] Valid Delay (Rising Edge) 1.5 8.7 ns 8 Notes 3, 4 PICD[1:0] Valid Delay (Falling Edge) 1.5 12.0 NOTES: 1. All AC timings for APIC signals are referenced to the PICCLK rising edge at 1.0V. All CMOS signals are referenced at 1.0V. 2. The minimum frequency is 2 MHz when PICD0 is at 1.5V at reset Referenced to PICCLK Rising Edge. 3. For Open-drain signals, Valid Delay is synonymous with Float Delay. 4. Valid delay timings for these signals are specified into 150 to 1.5V and 0 pF of external load. For real system timings these specifications must be derated for external capacitance at 105 ps/pF. 32 Datasheet 298517-001 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet 1 Table 21. TAP Signal AC Specifications Symbol Parameter T30 TCK Frequency T31 T32 Min Max Unit Figure Notes -- 16.67 MHz TCK Period 60 -- ns 6 TCK High Time 25.0 ns 6 VCMOSREF+0.2V, Note 2 T33 TCK Low Time 25.0 ns 6 VCMOSREF-0.2V, Note 2 T34 TCK Rise Time ns 6 (VCMOSREF-0.2V) - 5.0 (VCMOSREF+0.2V), Notes 2, 3 T35 TCK Fall Time 5.0 ns 6 (VCMOSREF+0.2V) - (VCMOSREF-0.2V) , Notes 2, 3 T36 TRST# Pulse Width 40.0 ns 16 Asynchronous, Note 2 T37 TDI, TMS Setup Time 5.0 ns 15 Note 4 T38 TDI, TMS Hold Time 14.0 T39 TDO Valid Delay 1.0 ns 15 Note 4 10.0 ns 15 Notes 5, 6 25.0 ns 15 Notes 2, 5, 6 25.0 ns 15 Notes 5, 7, 8 T40 TDO Float Delay T41 All Non-Test Outputs Valid Delay T42 All Non-Test Outputs Float Delay ns 15 Notes 2, 5, 7, 8 T43 All Non-Test Inputs Setup Time 5.0 ns 15 Notes 4, 7, 8 T44 All Non-Test Inputs Hold Time 13.0 ns 15 Notes 4, 7, 8 2.0 25.0 NOTES: 1. All AC timings for TAP signals are referenced to the TCK rising edge at 1.0V. All TAP and CMOS signals are referenced at 1.0V. 2. Not 100% tested. Specified by design/characterization. 3. 1 ns can be added to the maximum TCK rise and fall times for every 1 MHz below 16 MHz. 4. Referenced to TCK rising edge. 5. Referenced to TCK falling edge. 6. Valid delay timing for this signal is specified into 150 terminated to 1.5V and 0 pF of external load. For real system timings these specifications must be derated for external capacitance at 105 ps/pF. 7. Non-Test Outputs and Inputs are the normal output or input signals (except TCK, TRST#, TDI, TDO, and TMS). These timings correspond to the response of these signals due to boundary scan operations. 8. During Debug Port operation use the normal specified timings rather than the TAP signal timings. 1 Table 22. Quick Start/Deep Sleep AC Specifications Symbol T45 Parameter Quick Start Cycle Completion to Clock Stop or DPSLP# assertion Min Max 100 Unit Figure BCLKs 17, 18 0 s 17, 18 30 s 17, 18 0 ns 17, 18 8 BCLKs 17, 18 T46 Quick Start Cycle Completion to Input Signals Stable T47 Deep Sleep PLL Lock Latency 0 T48 STPCLK# Hold Time from PLL Lock T49 Input Signal Hold Time from STPCLK# Deassertion Notes Note 2 NOTES: 1. Input signals other than RESET# and BPRI# must be held constant in the Quick Start state. 2. The BCLK Settling Time specification (T60) applies to Deep Sleep state exit under all conditions. 298517-001 Datasheet 33 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet Figure 6. BCLK/PICCLK/TCK Generic Clock Timing Waveform Th Tr VH CLK VTRIP VL Tf Tl Tp D0003-01 NOTES: Tr=T5S, T5S1, T34, T25 (Rise Time) Tf=T6S, T6S1, T35, T26 (Fall Time) Th=T3S, T3S1, T32, T23 (High Time) Tl=T4S, T4S1, T33, T24 (Low Time) Tp=T1S, T1S1, T31, T22 (Period) VTRIP=1.25V for BCLK;1.0V for PICCLK; 1.0V for TCK VL=0.5V for BCLK; 0.4V for PICCLK; (VCMOSREF-0.2V) for TCK VH=2.0V for BCLK; 1.6V for PICCLK; (VCMOSREF+0.2V) for TCK Figure 7. Valid Delay Timings CLK Vc Vc TX Tx Signal V Valid Valid TPW D0004-00 NOTES: Tx = T7, T11, T29 (Valid Delay) Tpw = T14, T14B (Pulse Width) V = VREF for AGTL signal group; 1.0V for CMOS, Open-drain, APIC, and TAP signal groups Vc = 1.25V 34 Datasheet 298517-001 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet Figure 8. Setup and Hold Timings Vc CLK Ts Th V Valid Signal D0005-00 NOTES: Ts = T8, T27 (Setup Time) Th = T9, T28 (Hold Time) V = VREF for AGTL signals; 1.0V for CMOS, APIC, and TAP signals Vc = 1.25V Figure 9. Cold/Warm Reset and Configuration Timings VC BCLK Tu Tt V RESET# Tv Tx Tw Configuration (A[15:5], BREQ0#, FLUSH#, INIT#, PICD0) Valid Ty PICD[1:0] AGTL/non-AGTL outputs Valid Tz Non-configuration inputs Active D0006-02 NOTES: Tt = T9 (AGTL Input Hold Time) Tu = T8 (AGTL Input Setup Time) Tv = T10 (RESET# Pulse Width) Tw= T16 (Reset Configuration Signals (A[15:5]#, BREQ0#, FLUSH#, INIT#, PICD0) Setup Time) Tx = T17 (Reset Configuration Signals (A[15:5]#, BREQ0#, FLUSH#, INIT#, PICD0) Hold Time) Ty = T18D (RESET# inactive to Valid Outputs) Tz = T18E (RESET# inactive to Drive Signals) Vc= 1.25V 298517-001 Datasheet 35 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet Figure 10. Power-on Sequence and Reset Timings BCLK VCCT Td VTTPWRGD VIHVTTPWR,min VILVTTPWR,max Te VID[4:0]/ BSEL[1:0] Valid CMOSREF/ CLKREF/VREF VCC Ta Tc PWRGOOD VIH18,min VIL18,max Tb RESET# V0040-00 NOTES: Ta = T15 (PWRGOOD Inactive Pulse Width) Tb = T18 (RESET#/PWRGOOD Setup Time) Tc = T18B (Setup time from VCC valid until PWRGOOD assertion) Td = T18A (Setup time from VCCT valid to VTTPWRGD assertion) Te = T18C(VID, BSEL valid time before VTTPWRGD assertion) 36 Datasheet 298517-001 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet Figure 11. Power Down Sequencing and Timings (VCC Leading) VCCT, VREF VCCMOS, CMOSREF, CLKREF VID[4:0] BSEL[1:0] VTTPWRGD VCC-12% VCC BCLK Valid PICCLK Valid Ta VIL18 PWRGOOD RESET# PICD[1:0] Valid Tb AGTL OUTPUTS OTHER CMOS OUTPUTS Valid ALL INPUTS Valid Tc V0044-00 NOTES: Ta = T19A (Time from VCC(nominal)-12% to PWRGOOD low) Tb = T19B (All outputs valid after PWRGOOD low) Tc = T19C (All inputs required valid after PWRGOOD low) 298517-001 Datasheet 37 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet Figure 12.Power Down Sequencing and Timings (VCCT Leading) VCCT-12% VCCT, VREF VCMOS, CMOSREF, CLKREF Ta VILVTTPWR VTTPWRGD VID[4:0] BSEL[1:0] Valid VCC Tb, Tc, Td BCLK Valid PICCLK Valid PWRGOOD RESET# PICD[1:0] Valid AGTL OUTPUTS OTHER CMOS OUTPUTS Valid ALL INPUTS Valid V0045-00 NOTES: Ta = T20A (Time from VCCT-12% to VTTPWRGD low) Tb = T20B (All outputs valid after VTTPWRGD low) Tc = T20C (All inputs required valid after VTTPWRGD low) Td = T20D (VID, BSEL signals valid after VTTPWRGD low) 38 Datasheet 298517-001 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet Figure 13.Test Timings (Boundary Scan) TCK Tv Tw 0.75V TDI, TMS Tr Ts Input Signals Tx Tu Ty Tz TDO Output Signals D0008-01 NOTES: Tr=T43 (All Non-Test Inputs Setup Time) Ts=T44 (All Non-Test Inputs Hold Time) Tu=T40 (TDO Float Delay) Tv=T37 (TDI, TMS Setup Time) Tw=T38 (TDI, TMS Hold Time) Tx=T39 (TDO Valid Delay) Ty=T41 (All Non-Test Outputs Valid Delay) Tz=T42 (All Non-Test Outputs Float Delay) Figure 14. Test Reset Timings 0.75V TRST# Tq D0009-01 NOTE: Tq=T36 (TRST# Pulse Width) 298517-001 Datasheet 39 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet Figure 15.Quick Start/Deep Sleep Timing (BCLK Stopping Method) Normal Quick Start BCLK Deep Sleep Normal Stopped Tv STPCLK# Tx CPU bus Quick Start Ty stpgnt DPSLP# Tz Tw Compatibility Signals Changing Frozen V00102-00 NOTES: Tv=T45 (Stop Grant Acknowledge Bus Cycle Completion to Clock Shut Off Delay) Tw=T46 (Setup Time to Input Signal Hold Requirement) Tx=T47 (Deep Sleep PLL Lock Latency) Ty=T48 (PLL lock to STPCLK# Hold Time) Tz=T49 (Input Signal Hold Time) 40 Datasheet 298517-001 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet Figure 16. Quick Start/Deep Sleep Timing (DPSLP# Assertion Method) Normal Quick Start Deep Sleep Quick Start Normal BCLK Tv STPCLK# Tx CPU bus Ty stpgnt DPSLP# Tz Tw Compatibility Signals Changing Frozen V00103-00 NOTES: Tv=T45 (Stop Grant Acknowledge Bus Cycle Completion to DPSLP# assertion) Tw=T46 (Setup Time to Input Signal Hold Requirement) Tx=T47 (Deep Sleep PLL Lock Latency) Ty=T48 (PLL lock to STPCLK# Hold Time) Tz=T49 (Input Signal Hold Time) 298517-001 Datasheet 41 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet 4. System Signal Simulations Systems must be simulated using IBIS models to determine if they are compliant with this specification. 4.1 System Bus Clock (BCLK) and PICCLK DC Specifications and AC Signal Quality Specifications Table 23. BCLK DC Specifications and AC Signal Quality Specifications Symbol Parameter V1 VIL,BCLK V2 VIH,BCLK Min Max 0.3 2.2 Unit Figure Notes V 20 Note 1 V 20 Note 1 V3 VIN Absolute Voltage Range -0.5 3.1 V 20 Undershoot/Overshoot, Note 2 V4 BCLK Rising Edge Ringback 2.0 V 20 Absolute Value, Note 3 V5 BCLK Falling Edge Ringback V 20 Absolute Value, Note 3 0.5 NOTES: 1. The clock must rise/fall monotonically between VIL,BCLK and VIH,BCLK . BCLK must be stopped in the low state. 2. These specifications apply only when BCLK is running. BCLK may not be above VIH,BCLK,max or below VIL,BCLK,min for more than 50% of the clock cycle. 3. The rising and falling edge ringback voltage specified is the minimum (rising) or maximum (falling) absolute voltage the BCLK signal can go to after passing the VIH,BCLK (rising) or VIL,BCLK (falling) voltage limits. 42 Datasheet 298517-001 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet Table 24. PICCLK DC Specifications and AC Signal Quality Specifications Symbol Parameter V1 VIL20 V2 V3 Min Max Unit Figure 0.4 V VIH20 1.6 V 20 Note 1 VIN Absolute Voltage Range -0.5 2.4 V 20 Undershoot, Overshoot, Note 2 V4 PICCLK Rising Edge Ringback 1.6 V5 PICCLK Falling Edge Ringback 0.4 20 Notes Note 1 V 20 Absolute Value, Note 3 V 20 Absolute Value, Note 3 NOTES: 1. The clock must rise/fall monotonically between VIL20 and VIH20. 2. These specifications apply only when PICCLK is running. See the DC specifications for when PICCLK is stopped. PICCLK may not be above VIH20,max or below VIL20,min for more than 50% of the clock cycle. 3. The rising and falling edge ringback voltage specified is the minimum (rising) or maximum (falling) absolute voltage the PICCLK signal can go to after passing the VIH20 (rising) or VIL20 (falling) voltage limits. Figure 17. BCLK/PICCLK Generic Clock Waveform V3max V4 V2 V1 V5 V3min V0012-01 298517-001 Datasheet 43 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet 4.2 AGTL AC Signal Quality Specifications Ringback specifications for the AGTL signals are as follows: Ringback below VREF,max + 200 mV is not authorized during low to high transitions. Ringback above VREF,min - 200 mV is not authorized during high to low transitions. Overshoot and undershoot specifications are documented in Table 25 and illustrated in Figure 18. Figure 18. Maximum Acceptable Overshoot/Undershoot Waveform Time dependant Overshoot Max Vss Min Time dependant Undershoot 44 Datasheet 298517-001 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet Table 25. 100-MHz AGTL Signal Group Overshoot/Undershoot Tolerance at the Processor Core Max VCCT + Overshoot/Undershoot Magnitude (volts) Allowed Pulse Duration (ns) [Tj=100C] Activity Factor = 0.01 Activity Factor = 0.1 Activity Factor = 1 1.78 1.6 0.16 0.016 1.73 4.5 0.45 0.045 1.68 9.5 0.95 0.095 1.63 20 2.0 0.2 1.58 20 4.2 0.42 1.53 20 8.5 0.85 1.48 20 19 1.9 NOTES: 1. Under no circumstances should the sum of the Max VCCT and absolute value of the Overshoot/Undershoot voltage exceed 1.78V. 2. Activity factor of 1 represents the same toggle rate as the 100-MHz clock. 3. Ringbacks below VCCT cannot be subtracted from overshoots. Lesser undershoot does not allocate longer or larger overshoot. 4. Ringbacks above ground cannot be subtracted from undershoots. Lesser overshoot does not allocate longer or larger undershoot. 5. System designers are encouraged to follow Intel provided AGTL layout guidelines. 6. All values are specified by design characterization and are not tested. 4.3 Non-AGTL Signal Quality Specifications Signals driven to the Mobile Intel Celeron Processor should meet signal quality specifications to ensure that the processor reads data properly and that incoming signals do not affect the long-term reliability of the processor. The overshoot and undershoot specifications for non-AGTL signals are shown in Table 26. Ringback must not exceed the CMOS VIH and VIL specification levels in Table 14. Table 26. Non-AGTL Signal Group Overshoot/Undershoot Tolerance at the Processor Core Max VCmos + Overshoot/Undershoot Magnitude (volts) 2.38 Allowed Pulse Duration (ns) [Tj=100C] Activity Factor = 0.01 Activity Factor = 0.1 Activity Factor = 1 6.5 0.65 0.065 2.33 13 1.3 0.13 2.28 29 2.9 0.29 2.23 60 6 0.6 2.18 60 12 1.2 2.13 60 26 2.6 2.08 60 56 5.6 NOTES: 1. VCMOS(nominal) = 1.5V. 2. Under no circumstances should the sum of the Max VCMOS and absolute value of the Overshoot/Undershoot voltage exceed 2.38V. 3. Activity factor of 1 represents a toggle rate of 33 MHz. 4. System designers are encouraged to follow Intel provided non-AGTL layout guidelines. 5. All values are specified by design characterization, and are not tested. 298517-001 Datasheet 45 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet 4.3.1 PWRGOOD, VTTPWRGD Signal Quality Specifications The processor requires PWRGOOD to be a clean indication that clocks and the power supplies (VCC, VCCT, etc.) are stable and within their specifications. Clean implies that the signal will remain below VIL18 and without errors from the time that the power supplies are turned on, until they come within specification. The signal will then transition monotonically to a high (1.8V) state. The VTTPWRGD signal must also transition monotonically. 46 Datasheet 298517-001 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet 5. Mechanical Specifications 5.1 Surface Mount Micro-FCBGA Package The Low Voltage Mobile Intel Celeron Processor will also be available in a surface mount, 479-ball Micro-FCBGA package. The Low Voltage processor will be available only in this package. Mechanical specifications are shown in Table 27. Figure 19 through 22 illustrate different views of the package. The Micro-FCBGA package may have capacitors placed in the area surrounding the die. Because the die-side capacitors are electrically conductive, and only slightly shorter than the die height, care should be taken to avoid contacting the capacitors with electrically conductive materials. Doing so may short the capacitors, and possibly damage the device or render it inactive. The use of an insulating material between the capacitors and any thermal solution should be considered to prevent capacitor shorting. Table 27. Micro-FCBGA Package Mechanical Specifications Symbol Parameter Min A Overall height, as delivered (1) A2 Die height b Ball diameter D Package substrate length 34.9 E Package substrate width 34.9 D1 Die length Max 2.27 2.77 0.854 Unit mm mm 0.78 mm 35.1 35.1 mm mm 11.18 mm E1 Die width 7.19 mm e Ball pitch 1.27 mm N Ball count 479 each K Keep-out outline from edge of package 5 mm K1 Keep-out outline at corner of package 7 mm K2 Capacitor keep-out height S Package edge to first ball center - -- Solder ball coplanarity Pdie Allowable pressure on the die for thermal solution 0.7 1.625 0.2 - mm mm mm 689 kPa W Package weight 4.5 g NOTES: 1. All dimensions are subject to change. 2. Overall height as delivered. Values were based on design specifications and tolerances. Final height after surface mount depends on OEM motherboard design and SMT process. 298517-001 Datasheet 47 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet Figure 19. Micro-FCBGA Package - Top and Bottom Isometric Views PACKAGE KEEPOUT CAPACITOR AREA LABEL DIE TOP VIEW 48 BOTTOM VIEW Datasheet 298517-001 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet Figure 20. Micro-FCBGA Package - Top and Side Views SUBSTRATE KEEPOUT ZONE DO NOT CONTACT PACKAGE INSIDE THIS LINE 7 (K1) 8 places 5 (K) 4 places 0.20 A A2 D1 35 (D) O 0.78 (b) 479 places E1 35 (E) K2 PIN A1 CORNER NOTE: All dimensions in millimeters. Values shown are for reference only. See Table 27 for specific details 298517-001 Datasheet 49 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet Figure 21. Micro-FCBGA Package - Bottom View 1.625 (S) 4 places AF AD AB Y V T P M K H F D B AE AC 1.625 (S) 4 places AA W U R N L J G E C A 1 25X 1.27 (e) 3 2 5 4 7 6 9 8 10 11 13 15 17 19 21 23 25 12 14 16 18 20 22 24 26 25X 1.27 (e) NOTE: All dimensions in millimeters. Values shown are for reference only. See Table 27 for specific details. 50 Datasheet 298517-001 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet 5.2 Signal Listings Figure 22 is a top-side view of the ball or pin map of the Mobile Intel Celeron Processor with the voltage balls/pins called out. Table 28 lists the signals in ball/pin number order. Table 29 lists the signals in signal name order. Figure 22. Pin/Ball Map - Top View 1 2 3 4 5 NC A10# VREF NC 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 A27# A24# NC A35# A26# A33# A32# D0# D2# D15# D9# D7# VREF D8# D10# D11# VSS VCCT A A A31# BREQ0# A23# B B NC VSS A25# VSS A17# VSS A21# VSS A20# VSS A18# VSS A34# NC A16# A28# NC VCCT A19# VCCT A22# VCCT A30# VCCT A29# VCCT BERR# VCCT VSS RESET# VSS D1# VSS D4# VSS D17# VSS D18# D14# D24# VSS D6# VCCT D12# VCCT D5# VCCT NC VSS D20# VSS D30# NC VSS A13# VSS VCCT VCC VSS VCC VSS VCC VSS VCC VSS VCC VSS VCC VSS VCC VSS VCC VSS VCC D3# D13# D22# NC NC TESTHI VCC VCCT VCC VSS VCC VSS VCC VSS VCC VSS VCC VSS VCC VSS VCC VSS VCC VSS D16# D23# VSS D19# NC VSS A14# VSS VSS VCC VSS VCC VSS VCC VSS VCC VSS VCC VSS VCC VSS VCC VSS VCC VSS VCC VSS D21# D36# D27# A9# A5# A15# VCCT VCC VSS VCC VSS VCCT D25# VSS D32# A12# VSS A8# VSS VSS VCC VSS VCC VSS D26# D29# VREF A4# A7# A11# VCCT VCC VSS VCC VSS VCCT D34# VSS D38# C C D D E E VTT VCCT PWRGD F F G G H H J J K K A3# VSS A6# VSS VSS VCC VSS VCC VSS D31# D33# D35# NC VSS VCC VSS VCCT D28# VSS D42# L L REQ4# BNR# REQ1# VCCT M M TESTLO VSS VSS VSS RSP# VCC VSS VCC VSS D39# D45# D48# VREF PLL2 PLL1 NC VCC VSS VCC VSS VCCT NC VSS D37# NC VSS API# NC NC VCC VSS VCC VSS D49# D41# NC VID4 VSS VCC VSS VCC VSS VCCT D43# VSS D44# RP# VSS VCC VSS VCC VSS D47# D57# D51# VSS VCC VSS VCC VSS VCCT D52# VSS D40# VSS VCC VSS VCC VSS D63# D46# D55# VCC VSS VCC VSS VCCT D59# VSS D54# VSS VCC VSS D58# D53# D60# N N P P R R REQ0# BPRI# T T REQ2# VSS DEFER# U U REQ3# HITM# RS2# V V RS1# VSS LOCK# VCCT W W TRDY# AERR# DBSY# VSS Y Y DRDY# VSS RS0# TESTLO VSS VCC VREF HIT# ADS# VCCT VCC VSS VCC VSS VCC VSS VCC VSS VCC VSS VCC VSS VCC VSS VCC VSS VCC VSS VCCT D62# VSS D50# VID0 VSS AP0# PWR GOOD VSS VCC VSS VCC VSS VCC VSS VCC VSS VCC VSS VCC VSS VCC VSS VCC VSS VCC VSS D61# D56# VREF BCLK VID1 A20M# VCCT VCC VSS VCC VSS VCC VSS VCC VSS VCC VSS VCC VSS VCC VSS VCC VSS VCC VSS VCCT DEP3# VSS DEP6# CMOS REF VCCT TDI TCK TDO VCCT NC VCCT LINT0 NCTRL PICD1 VCCT PICD0 INIT# VSS NC VSS BSEL0 VSS LINT1 RTT IMPEDP VSS VCCT VSS NC NC 17 18 AA AA AB AB AC AC AD AD VSS SMI# VSS VID2 VCCT STPCLK# VSS VCCT VCCT VID3 1 2 3 CLKREF NC VCCT IGNNE# VCCT BPM1# BPM0# NC DEP7# DEP1# DEP5# AE AE NC VSS VSS BP3# VSS PRDY# VSS DEP0# DEP2# VSS AF AF VCC 298517-001 IERR# FLUSH# FERR# 4 VSS 5 6 TMS DPSLP# VREF 7 8 9 BSEL1 TESTHI CMOS THRMDATHRMDC TRST# EDGE REF CTRLP 10 11 12 13 14 15 16 PREQ# PICCLK VREF 19 20 21 BP2# 22 BINIT# DEP4# 23 24 VSS VSS 25 26 VCCT Other Datasheet 51 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet Table 28. Signal Listing in Order by Pin/Ball Number No. 52 Signal Name No. Signal Name No. Signal Name No. Signal Name A3 A10# B18 VSS D7 VSS E22 VSS A4 VREF B19 D4# D8 VCC E23 D16# A5 NC B20 VSS D9 VSS E24 D23# A6 A31# B21 D17# D10 VCC E25 VSS A7 BREQ0# B22 VSS D11 VSS E26 D19# A8 A23# B23 D18# D12 VCC F1 NC A9 A27# B24 D14# D13 VSS F2 VSS A10 A24# B25 D24# D14 VCC F3 A14# A11 NC B26 VSS D15 VSS F4 VSS A12 A35# C1 NC D16 VCC F5 VSS A13 A26# C2 A16# D17 VSS F6 VCC A14 A33# C3 A28# D18 VCC F7 VSS A15 A32# C4 NC D19 VSS F8 VCC A16 D0# C5 VCCT D20 VCC F9 VSS A17 D2# C6 A19# D21 VSS F10 VCC A18 D15# C7 VCCT D22 VCC F11 VSS A19 D9# C8 A22# D23 D3# F12 VCC A20 D7# C9 VCCT D24 D13# F13 VSS A21 VREF C10 A30# D25 D22# F14 VCC A22 D8# C11 VCCT D26 NC F15 VSS A23 D10# C12 A29# E1 NC F16 VCC A24 D11# C13 VCCT E2 TESTHI F17 VSS A25 VSS C14 BERR# E3 VTTPWRGD F18 VCC A26 VCCT C15 VCCT E4 VCCT F19 VSS B1 NC C16 D6# E5 VCC F20 VCC B2 VSS C17 VCCT E6 VCCT F21 VSS B3 A25# C18 D12# E7 VCC F22 VCC B4 VSS C19 VCCT E8 VSS F23 VSS B5 A17# C20 D5# E9 VCC F24 D21# B6 VSS C21 VCCT E10 VSS F25 D36# B7 A21# C22 NC E11 VCC F26 D27# B8 VSS C23 VSS E12 VSS G1 A9# B9 A20# C24 D20# E13 VCC G2 A5# B10 VSS C25 VSS E14 VSS G3 A15# B11 A18# C26 D30# E15 VCC G4 VCCT B12 VSS D1 NC E16 VSS G5 VCC B13 A34# D2 VSS E17 VCC G6 VSS B14 VSS D3 A13# E18 VSS G21 VCC B15 RESET# D4 VSS E19 VCC G22 VSS B16 VSS D5 VCCT E20 VSS G23 VCCT B17 D1# D6 VCC E21 VCC G24 D25# Datasheet 298517-001 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet No. 298517-001 Signal Name No. Signal Name No. Signal Name No. Signal Name G25 VSS L4 VCCT P23 VSS V2 VSS G26 D32# L5 NC P24 D49# V3 LOCK# H1 A12# L6 VSS P25 D41# V4 VCCT H2 VSS L21 VCC P26 NC V5 VSS H3 A8# L22 VSS R1 REQ0# V6 VCC H4 VSS L23 VCCT R2 BPRI# V21 VSS H5 VSS L24 D28# R3 VID4 V22 VCC H6 VCC L25 VSS R4 VSS V23 VSS H21 VSS L26 D42# R5 VCC V24 D63# H22 VCC M1 TESTLO R6 VSS V25 D46# H23 VSS M2 VSS R21 VCC V26 D55# H24 D26# M3 VSS R22 VSS W1 TRDY# H25 D29# M4 VSS R23 VCCT W2 AERR# H26 VREF M5 RSP# R24 D43# W3 DBSY# J1 A4# M6 VCC R25 VSS W4 VSS J2 A7# M21 VSS R26 D44# W5 VCC J3 A11# M22 VCC T1 REQ2# W6 VSS J4 VCCT M23 VSS T2 VSS W21 VCC J5 VCC M24 D39# T3 DEFER# W22 VSS J6 VSS M25 D45# T4 RP# W23 VCCT J21 VCC M26 D48# T5 VSS W24 D59# J22 VSS N1 VREF T6 VCC W25 VSS J23 VCCT N2 PLL2 T21 VSS W26 D54# J24 D34# N3 PLL1 T22 VCC Y1 DRDY# J25 VSS N4 NC T23 VSS Y2 VSS J26 D38# N5 VCC T24 D47# Y3 RS0# K1 A3# N6 VSS T25 D57# Y4 TESTLO K2 VSS N21 VCC T26 D51# Y5 VSS K3 A6# N22 VSS U1 REQ3# Y6 VCC K4 VSS N23 VCCT U2 HITM# Y21 VSS K5 VSS N24 NC U3 RS2# Y22 VCC K6 VCC N25 VSS U4 VSS Y23 VSS K21 VSS N26 D37# U5 VCC Y24 D58# K22 VCC P1 NC U6 VSS Y25 D53# K23 VSS P2 VSS U21 VCC Y26 D60# K24 D31# P3 API# U22 VSS AA1 VREF K25 D33# P4 NC U23 VCCT AA2 HIT# K26 D35# P5 NC U24 D52# AA3 ADS# L1 REQ4# P6 VCC U25 VSS AA4 VCCT L2 BNR# P21 VSS U26 D40# AA5 VCC L3 REQ1# P22 VCC V1 RS1# AA6 VSS Datasheet 53 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet No. 54 Signal Name No. Signal Name No. Signal Name No. Signal Name AA7 VCC AB22 VCC AD11 TDO AE26 VSS AA8 VSS AB23 VSS AD12 VCCT AF1 VCCT AA9 VCC AB24 D61# AD13 NC AF2 VCCT AA10 VSS AB25 D56# AD14 VCCT AF3 VID3 AA11 VCC AB26 VREF AD15 LINT0 AF4 IERR# AA12 VSS AC1 BCLK AD16 NCTRL AF5 FLUSH# AA13 VCC AC2 VID1 AD17 PICD1 AF6 FERR# AA14 VSS AC3 A20M# AD18 VCCT AF7 TMS AA15 VCC AC4 VCCT AD19 PICD0 AF8 DPSLP# AA16 VSS AC5 VCC AD20 VCCT AF9 VREF AA17 VCC AC6 VSS AD21 BPM1# AF10 BSEL1 AA18 VSS AC7 VCC AD22 BPM0# AF11 TESTHI AA19 VCC AC8 VSS AD23 NC AF12 CMOSREF AA20 VSS AC9 VCC AD24 DEP7# AF13 THRMDA AA21 VCC AC10 VSS AD25 DEP1# AF14 THRMDC AA22 VSS AC11 VCC AD26 DEP5# AF15 TRST# AA23 VCCT AC12 VSS AE1 VSS AF16 EDGECTRLP AA24 D62# AC13 VCC AE2 VID2 AF17 NC AA25 VSS AC14 VSS AE3 VCCT AF18 NC AA26 D50# AC15 VCC AE4 STPCLK# AF19 PREQ# AB1 VID0 AC16 VSS AE5 VSS AF20 PICCLK AB2 VSS AC17 VCC AE6 INIT# AF21 VREF AB3 AP0# AC18 VSS AE7 VSS AF22 BP2# AB4 PWRGOOD AC19 VCC AE8 NC AF23 BINIT# AB5 VSS AC20 VSS AE9 VSS AF24 DEP4# AB6 VCC AC21 VCC AE10 NC AF25 VSS AB7 VSS AC22 VSS AE11 VSS AF26 VSS AB8 VCC AC23 VCCT AE12 BSEL0 AB9 VSS AC24 DEP3# AE13 VSS AB10 VCC AC25 VSS AE14 LINT1 AB11 VSS AC26 DEP6# AE15 VSS AB12 VCC AD1 CLKREF AE16 RTTIMPEDP AB13 VSS AD2 VSS AE17 VSS AB14 VCC AD3 SMI# AE18 VCCT AB15 VSS AD4 NC AE19 VSS AB16 VCC AD5 CMOSREF AE20 BP3# AB17 VSS AD6 VCCT AE21 VSS AB18 VCC AD7 TDI AE22 PRDY# AB19 VSS AD8 VCCT AE23 VSS AB20 VCC AD9 IGNNE# AE24 DEP0# AB21 VSS AD10 TCK AE25 DEP2# Datasheet 298517-001 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet Table 29. Signal Listing in Order by Signal Name No. K1 298517-001 Signal Name Signal Buffer Type No. Signal Name Signal Buffer Type A3# AGTL I/O AF23 BINIT# AGTL I/O J1 A4# AGTL I/O L2 BNR# AGTL I/O G2 A5# AGTL I/O AF22 BP2# AGTL I/O K3 A6# AGTL I/O AE20 BP3# AGTL I/O J2 A7# AGTL I/O AD22 BPM0# AGTL I/O H3 A8# AGTL I/O AD21 BPM1# AGTL I/O G1 A9# AGTL I/O R2 BPRI# AGTL Input A3 A10# AGTL I/O A7 BREQ0# AGTL I/O J3 A11# AGTL I/O AE12 BSEL0 3.3V CMOS Output H1 A12# AGTL I/O AF10 BSEL1 3.3V CMOS Output D3 A13# AGTL I/O AD5 CMOSREF CMOS Reference Voltage F3 A14# AGTL I/O AF12 CMOSREF CMOS Reference Voltage G3 A15# AGTL I/O A16 D0# AGTL I/O C2 A16# AGTL I/O B17 D1# AGTL I/O B5 A17# AGTL I/O A17 D2# AGTL I/O B11 A18# AGTL I/O D23 D3# AGTL I/O C6 A19# AGTL I/O B19 D4# AGTL I/O B9 A20# AGTL I/O C20 D5# AGTL I/O B7 A21# AGTL I/O C16 D6# AGTL I/O C8 A22# AGTL I/O A20 D7# AGTL I/O A8 A23# AGTL I/O A22 D8# AGTL I/O A10 A24# AGTL I/O A19 D9# AGTL I/O B3 A25# AGTL I/O A23 D10# AGTL I/O A13 A26# AGTL I/O A24 D11# AGTL I/O A9 A27# AGTL I/O C18 D12# AGTL I/O C3 A28# AGTL I/O D24 D13# AGTL I/O C12 A29# AGTL I/O B24 D14# AGTL I/O C10 A30# AGTL I/O A18 D15# AGTL I/O A6 A31# AGTL I/O E23 D16# AGTL I/O A15 A32# AGTL I/O B21 D17# AGTL I/O A14 A33# AGTL I/O B23 D18# AGTL I/O B13 A34# AGTL I/O E26 D19# AGTL I/O A12 A35# AGTL I/O C24 D20# AGTL I/O AC3 A20M# 1.5V CMOS Input F24 D21# AGTL I/O AA3 ADS# AGTL I/O D25 D22# AGTL I/O W2 AERR# AGTL I/O E24 D23# AGTL I/O AB3 AP0# AGTL I/O B25 D24# AGTL I/O P3 AP1# AGTL I/O G24 D25# AGTL I/O AC1 BCLK Clock Input H24 D26# AGTL I/O AD1 CLKREF Clock Input F26 D27# AGTL I/O C14 BERR# AGTL I/O L24 D28# AGTL I/O Datasheet 55 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet No. H25 56 Signal Name D29# Signal Buffer Type AGTL I/O No. AF24 Signal Name Signal Buffer Type DEP4# AGTL I/O C26 D30# AGTL I/O AD26 DEP5# AGTL I/O K24 D31# AGTL I/O AC26 DEP6# AGTL I/O G26 D32# AGTL I/O AD24 DEP7# AGTL I/O K25 D33# AGTL I/O Y1 DRDY# AGTL I/O J24 D34# AGTL I/O AF8 DPSLP# 1.5V CMOS Input K26 D35# AGTL I/O AF16 EDGECTRLP AGTL Control F25 D36# AGTL I/O AF6 FERR# 1.5V Open Drain Output N26 D37# AGTL I/O AF5 FLUSH# 1.5V CMOS Input J26 D38# AGTL I/O AA2 HIT# AGTL I/O M24 D39# AGTL I/O U2 HITM# AGTL I/O U26 D40# AGTL I/O AF4 IERR# 1.5V Open Drain Output P25 D41# AGTL I/O AD9 IGNNE# 1.5V CMOS Input L26 D42# AGTL I/O AE6 INIT# 1.5V CMOS Input R24 D43# AGTL I/O AD15 INTR/LINT0 1.5V CMOS Input R26 D44# AGTL I/O V3 LOCK# AGTL I/O M25 D45# AGTL I/O AE14 NMI/LINT1 1.5V CMOS Input V25 D46# AGTL I/O AD16 NCTRL AGTL impedance control T24 D47# AGTL I/O AF20 PICCLK 1.8V APIC Clock Input M26 D48# AGTL I/O AD19 PICD0 1.5V Open Drain I/O P24 D49# AGTL I/O AD17 PICD1 1.5V Open Drain I/O AA26 D50# AGTL I/O N3 PLL1 PLL Analog Voltage T26 D51# AGTL I/O N2 PLL2 PLL Analog Voltage U24 D52# AGTL I/O AE22 PRDY# AGTL Output Y25 D53# AGTL I/O AF19 PREQ# 1.5V CMOS Input W26 D54# AGTL I/O AB4 PWRGOOD 1.8V CMOS Input V26 D55# AGTL I/O R1 REQ0# AGTL I/O AB25 D56# AGTL I/O L3 REQ1# AGTL I/O T25 D57# AGTL I/O T1 REQ2# AGTL I/O Y24 D58# AGTL I/O U1 REQ3# AGTL I/O W24 D59# AGTL I/O L1 REQ4# AGTL I/O Y26 D60# AGTL I/O B15 RESET# AGTL Input AB24 D61# AGTL I/O T4 RP# AGTL I/O AA24 D62# AGTL I/O Y3 RS0# AGTL I/O V24 D63# AGTL I/O V1 RS1# AGTL I/O W3 DBSY# AGTL I/O U3 RS2# AGTL I/O T3 DEFER# AGTL Input M5 RSP# AGTL Input AE24 DEP0# AGTL I/O AE16 RTTIMPEDP AGTL Pull-up Control AD25 DEP1# AGTL I/O AD3 SMI# 1.5V CMOS Input AE4 STPCLK# 1.5V CMOS Input AE25 DEP2# AGTL I/O AC24 DEP3# AGTL I/O Datasheet 298517-001 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet No. Signal Name Signal Buffer Type 1.5V JTAG Clock Input No. AC2 Signal Name VID1 Signal Buffer Type AD10 TCK Voltage Identification AD7 TDI JTAG Input AE2 VID2 Voltage Identification AD11 TDO JTAG Output AF3 VID3 Voltage Identification E2 TESTHI Test Use Only R3 VID4 Voltage Identification AF11 TESTHI Test Use Only A4 VREF AGTL Reference Voltage M1 TESTLO Test Use Only A21 VREF AGTL Reference Voltage Y4 TESTLO Test Use Only N1 VREF AGTL Reference Voltage AF13 THERMDA Thermal Diode Anode AF9 VREF AGTL Reference Voltage AF14 THERMDC Thermal Diode Cathode AF21 VREF AGTL Reference Voltage AF7 TMS JTAG Input AA1 VREF AGTL Reference Voltage W1 TRDY# AGTL I/O AB26 VREF AGTL Reference Voltage AF15 TRST# JTAG Input H26 VREF AGTL Reference Voltage AB1 VID0 Voltage Identification E3 VTTPWRGD VCCT power good signal Table 30. Voltage and No-Connect Pin/Ball Locations Signal Name NC VCC Pin/Ball Numbers A2, A5, A11, B1, C1, C4, C22, D1, D26, E1, F1, L5, N4, N24, P1, P4, P5, P26, AD4, AD13, AD23, AE8, AE10, AF17, AF18 D6, D8, D10, D12, D14, D16, D18, D20, D22, E5, E7, E9, E11, E13, E15, E17, E19, E21, F6, F8, F10, F12, F14, F16, F18, F20, F22, G5, G21, H6, H22, J5, J21, K6, K22, L21, M6, M22, N5, N21, P6, P22, R5, R21, T6, T22, U5, U21, V6, V22, W5, W21, Y6, Y22, AA5, AA7, AA9, AA11, AA13, AA15, AA17, AA19, AA21, AB6, AB8, AB10, AB12, AB14, AB16, AB18, AB20, AB22, AC5, AC7, AC9, AC11, AC13, AC15, AC17, AC19, AC21 298517-001 VCCT A26, C5, C7, C9, C11, C13, C15, C17, C19, C21, D5, E4, E6, G4, G23, J4, J23, L4, L23, N23, R23, U23, V4, W23, AA4, AA23, AC4, AC23, AD6, AD8, AD12, AD14, AD18, AD20, AE3, AE18, AF1, AF2 VSS A25, B2, B4, B6, B8, B10, B12, B14, B16, B18, B20, B22, B26, C23, C25, D2, D4, D7, D9, D11, D13, D15, D17, D19, D21, E8, E10, E12, E14, E16, E18, E20, E22, E25, F2, F4, F5, F7, F9, F11, F13, F15, F17, F19, F21, F23, G6, G22, G25, H2, H4, H5, H21, H23, J6, J22, J25, K2, K4, K5, K21, K23, L6, L22, L25, M2, M3, M4, M21, M23, N6, N22, N25, P2, P21, P23, R4, R6, R22, R25, T2, T5, T21, T23, U4, U6, U22, U25, V2, V5, V21, V23, W4, W6, W22, W25, Y2, Y5, Y21, Y23, AA6, AA8, AA10, AA12, AA14, AA16, AA18, AA20, AA22, AA25, AB2, AB5, AB7, AB9, AB11, AB13, AB15, AB17, AB19, AB21, AB23, AC6, AC8, AC10, AC12, AC14, AC16, AC18, AC20, AC22, AC25, AD2, AE1, AE5, AE7, AE9, AE11, AE13, AE15, AE17, AE19, AE21, AE23, AE26, AF25, AF26 Datasheet 57 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet 6. VCC Thermal Specifications In order to achieve proper cooling of the processor, a thermal solution (e.g., heat spreader, heat pipe, or other heat transfer system) must make firm contact to the exposed processor die. The processor die must be clean before the thermal solution is attached or the processor may be damaged. Table 31 provides the Thermal Design Power (TDP) dissipation and the minimum and maximum TJ temperatures for the Mobile Intel Celeron Processor. The thermal solution should be designed to ensure the junction temperature never exceeds the 100C TJ specification while operating at the Thermal Design Power. Additionally, a secondary failsafe mechanism in hardware should be provided to shutdown the processor at 101C to prevent permanent damage, as described in Section 3.1.3. TDP is a thermal design power specification based on the worst case power dissipation of the processor while executing publicly available software under normal operating conditions at nominal voltages. Contact your Intel Field Sales Representative for further information. Table 31. Power Specifications for Mobile Intel Celeron Processor Symbol TDP Core Frequency/Voltage 10.6 650 MHz & 1.15V Symbol PAH Thermal Design Power Parameter Min 3.6 At 100C, Note 1 Unit Notes W At 50C, Note 2 Quick Start power at 3.2 Deep Sleep power at 1.15V TJ Max Notes At 50C, Note 2 1.15V PDSLP W Auto Halt power at: 1.15V PQS Unit W W At 35C, Note 2 C Note 3 2.4 0 Junction Temperature 100 NOTES: 1. TDP is defined as the worst case power dissipated by the processor while executing publicly available software under normal operating conditions at nominal voltages that meet the load line specifications. The TDP number show is a specification based on Icc(maximum) and indirectly tested by Icc(maximum) testing. TDP definition is synonymous with the Thermal Design Power (typical) specification referred to in previous Intel datasheets. The Intel TDP specification is a recommended design point and is not representative of the absolute maximum power the processor may dissipate under worst case conditions. 2. Not 100% tested. These power specifications are determined by characterization of the processor currents at higher temperatures and extrapolating the values for the temperature indicated. 3. TJ is measured with the on-die thermal diode. 6.1 Thermal Diode The Mobile Intel Celeron Processor has an on-die thermal diode that should be used to monitor the die temperature(TJ). A thermal sensor located on the motherboard, or a stand-alone measurement kit, should monitor the die temperature of the processor for thermal management or instrumentation purposes. Table 32 and Table 33 provide the diode interface and specifications. 58 Datasheet 298517-001 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet Note: The reading of the thermal sensor connected to the thermal diode will not necessarily reflect the temperature of the hottest location on the die. This is due to inaccuracies in the thermal sensor, on-die temperature gradients between the location of the thermal diode and the hottest location on the die, and time based variations in the die temperature measurement. Time based variations can occur when the sampling rate of the thermal diode (by the thermal sensor) is slower than the rate at which the TJ temperature can change. Table 32. Thermal Diode Interface Signal Name Pin/Ball Number Signal Description THERMDA AF13 Thermal diode anode THERMDC AF14 Thermal diode cathode Table 33. Thermal Diode Specifications Symbol Parameter Min Typ Max Unit Notes n Diode Ideality Factor (5-150uA) 1.0011 1.0067 1.0122 Notes 1, 2, 3, 4, 6 n Diode Ideality Factor (5-300uA) 1.0003 1.0091 1.0178 Notes 1, 2, 3, 5, 6 NOTES: 1. Intel does not support or recommend operation of the thermal diode under reverse bias. Intel does not support or recommend operation of the thermal diode when the processor power supplies are not within their specified tolerance range. 2. Characterized at 100C. 3. Not 100% tested. Specified by design/characterization. 4. Specified for Forward Bias Current = 5 A (min) and 150 A (max). 5. Specified for Forward Bias Current = 5 A (min) and 300 A (max). 6. The ideality factor, n, represents the deviation from ideal diode behavior as exemplified by the diode equation: Where Is = saturation current, q = electronic charge, Vd = voltage across the diode, k = Boltzmann Constant, and T = absolute temperature (Kelvin). qVD IFW = IS e nkT - 1 298517-001 Datasheet 59 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet 7. Processor Initialization and Configuration 7.1 Description The Mobile Intel Celeron Processor has some configuration options that are determined by hardware and some that are determined by software. The processor samples its hardware configuration at reset on the active-to-inactive transition of RESET#. The P6 Family of Processors Developer's Manual describes these configuration options. Some of the configuration options for the Mobile Intel Celeron Processor are described in the remainder of this section. 7.1.1 Quick Start Enable Quick Start enabling is mandatory on the Mobile Intel Celeron Processor by strapping A15# low. When the STPCLK# signal is asserted it will enter the Quick Start state when A15# is sampled active on the RESET# signal's active-to-inactive transition. The Quick Start state supports snoops from the bus priority device but it does not support symmetric master snoops nor is the latching of interrupts supported. A "1" in bit position 5 of the Power-on Configuration register indicates that the Quick Start state has been enabled. 7.1.2 System Bus Frequency The Low Voltage Mobile Intel Celeron Processor supports 100-MHz bus frequency. Bit positions 18 to 19 of the Power-on Configuration register indicates at which speed a processor will run. 7.1.3 APIC Enable The processor APIC must be hardware enabled by pulling the PICD[1:0] signals separately up to 1.5V and supplying an active PICCLK to the processor. Software can be used to disable the APIC if it is not being used, after PICD[1:0] are sampled high when RESET# is deasserted and the processor has started executing instructions. 7.2 Clock Frequencies and Ratios The Mobile Intel Celeron Processor uses a clock design in which the bus clock is multiplied by a ratio to produce the processor's internal (or "core") clock. The ratio used is programmed into the processor during manufacturing. The bus ratio programmed into the processor is visible in bit positions 22 to 25 and 27 of the Power-on Configuration register. Table 16 shows the 5-bit codes in the Power-on Configuration register and their corresponding bus ratios. 60 Datasheet 298517-001 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet 8. Processor Interface 8.1 Alphabetical Signal Reference A[35:3]# (I/O - AGTL) The A[35:3]# (Address) signals define a 236-byte physical memory address space. When ADS# is active, these signals transmit the address of a transaction; when ADS# is inactive, these signals transmit transaction information. These signals must be connected to the appropriate pins/balls of both agents on the system bus. The A[35:24]# signals are protected with the AP1# parity signal, and the A[23:3]# signals are protected with the AP0# parity signal. On the active-to-inactive transition of RESET#, each processor bus agent samples A[35:3]# signals to determine its power-on configuration. See P6 Family of Processors Developer's Manual for details. A20M# (I - 1.5V Tolerant) If the A20M# (Address-20 Mask) input signal is asserted, the processor masks physical address bit 20 (A20#) before looking up a line in any internal cache and before driving a read/write transaction on the bus. Asserting A20M# emulates the 8086 processor's address wrap-around at the 1-Mbyte boundary. Assertion of A20M# is only supported in Real mode. ADS# (I/O - AGTL) The ADS# (Address Strobe) signal is asserted to indicate the validity of a transaction address on the A[35:3]# signals. Both bus agents observe the ADS# activation to begin parity checking, protocol checking, address decode, internal snoop or deferred reply ID match operations associated with the new transaction. This signal must be connected to the appropriate pins/balls on both agents on the system bus. AERR# (I/O - AGTL) The AERR# (Address Parity Error) signal is observed and driven by both system bus agents, and if used, must be connected to the appropriate pins/balls of both agents on the system bus. AERR# observation is optionally enabled during power-on configuration; if enabled, a valid assertion of AERR# aborts the current transaction. If AERR# observation is disabled during power-on configuration, a central agent may handle an assertion of AERR# as appropriate to the error handling architecture of the system. AP[1:0]# (I/O - AGTL) The AP[1:0]# (Address Parity) signals are driven by the request initiator along with ADS#, A[35:3]#, REQ[4:0]# and RP#. AP1# covers A[35:24]#. AP0# covers A[23:3]#. A correct parity signal is high if an even number of covered signals is low and low if an odd number of covered signals are low. This allows parity to be high when all the covered signals are high. AP[1:0]# should be connected to the appropriate pins/balls on both agents on the system bus. 298517-001 Datasheet 61 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet BCLK The BCLK signal determines the system bus frequency. Both system bus agents must receive the BCLK signal to drive their outputs and latch their inputs on the BCLK rising edge. All external timing parameters are specified with respect to the BCLK signal. BERR# (I/O - AGTL) The BERR# (Bus Error) signal is asserted to indicate an unrecoverable error without a bus protocol violation. It may be driven by either system bus agent and must be connected to the appropriate pins/balls of both agents, if used. However, the Mobile Intel Celeron Processors do not observe assertions of the BERR# signal. BERR# assertion conditions are defined by the system configuration. Configuration options enable the BERR# driver as follows: * Enabled or disabled * Asserted optionally for internal errors along with IERR# * Asserted optionally by the request initiator of a bus transaction after it observes an error * Asserted by any bus agent when it observes an error in a bus transaction BINIT# (I/O - AGTL) The BINIT# (Bus Initialization) signal may be observed and driven by both system bus agents and must be connected to the appropriate pins/balls of both agents, if used. If the BINIT# driver is enabled during the power-on configuration, BINIT# is asserted to signal any bus condition that prevents reliable future information. If BINIT# is enabled during power-on configuration, and BINIT# is sampled asserted, all bus state machines are reset and any data which was in transit is lost. All agents reset their rotating ID for bus arbitration to the state after reset, and internal count information is lost. The L1 and L2 caches are not affected. If BINIT# is disabled during power-on configuration, a central agent may handle an assertion of BINIT# as appropriate to the Machine Check Architecture (MCA) of the system. BNR# (I/O - AGTL) The BNR# (Block Next Request) signal is used to assert a bus stall by any bus agent that is unable to accept new bus transactions. During a bus stall, the current bus owner cannot issue any new transactions. Since multiple agents may need to request a bus stall simultaneously, BNR# is a wired-OR signal that must be connected to the appropriate pins/balls of both agents on the system bus. In order to avoid wireOR glitches associated with simultaneous edge transitions driven by multiple drivers, BNR# is activated on specific clock edges and sampled on specific clock edges. BP[3:2]# (I/O - AGTL) The BP[3:2]# (Breakpoint) signals are the System Support group Breakpoint signals. They are outputs from the processor that indicate the status of breakpoints. 62 Datasheet 298517-001 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet BPM[1:0]# (I/O - AGTL) The BPM[1:0]# (Breakpoint Monitor) signals are breakpoint and performance monitor signals. They are outputs from the processor that indicate the status of breakpoints and programmable counters used for monitoring processor performance. BPRI# (I - AGTL) The BPRI# (Bus Priority Request) signal is used to arbitrate for ownership of the system bus. It must be connected to the appropriate pins/balls on both agents on the system bus. Observing BPRI# active (as asserted by the priority agent) causes the processor to stop issuing new requests, unless such requests are part of an ongoing locked operation. The priority agent keeps BPRI# asserted until all of its requests are completed and then releases the bus by deasserting BPRI#. BREQ0# (I/O - AGTL) The BREQ0# (Bus Request) signal is a processor Arbitration Bus signal. The processor indicates that it wants ownership of the system bus by asserting the BREQ0# signal. During power-up configuration, the central agent must assert the BREQ0# bus signal. The processor samples BREQ0# on the active-to-inactive transition of RESET#. Optionally, this signal may be grounded with a 10-ohm resistor. BSEL[1:0] (O - 3.3V Tolerant) The BSEL[1:0] (Select Processor System Bus Speed) signal is used to configure the processor for the system bus frequency. The chipset and system clock generator also uses the BSEL signals. The VTTPWRGD signal informs the processor to output the BSEL signals. During power up the BSEL signals will be indeterminate for a small period of time. The chipset and clock generator should not sample the BSEL signals until the VTTPWRGD signal is asserted. The assertion of the VTTPWRGD signal indicates that the BSEL signals are stable and driven to a final state by the processor. Please refer to Figure 10 for the timing relationship between the BSEL and VTTPWRGD signals. Table 34 shows the encoding scheme for BSEL[1:0]. The Low Voltage Mobile Intel Celeron Processors will support 100-MHz bus frequency. If another frequency is used then the processor is not guaranteed to function properly. Table 34. BSEL[1:0] Encoding BSEL[1:0] System Bus Frequency 01 100 MHz CLKREF (Analog) The CLKREF (System Bus Clock Reference) signal provides a reference voltage to define the trip point for the BCLK signal. This signal should be connected to a resistor divider to generate 1.25V from the 2.5-V supply. A minimum of 1-uF decoupling capacitance is recommended on CLKREF. CMOSREF (Analog) The CMOSREF (CMOS Reference Voltage) signal provides a DC level reference voltage for the CMOS input buffers. CMOSREF must be generated from a stable 1.5V supply and must meet the VCMOSREF 298517-001 Datasheet 63 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet specification. The same 1.5V supply should be used to power the chipset CMOS I/O buffers that drive the CMOS signals. Please refer to the platform design guidelines for resistor divider recommendations. D[63:0]# (I/O - AGTL) The D[63:0]# (Data) signals are the data signals. These signals provide a 64-bit data path between both system bus agents, and must be connected to the appropriate pins/balls on both agents. The data driver asserts DRDY# to indicate a valid data transfer. DBSY# (I/O - AGTL) The DBSY# (Data Bus Busy) signal is asserted by the agent responsible for driving data on the system bus to indicate that the data bus is in use. The data bus is released after DBSY# is deasserted. This signal must be connected to the appropriate pins/balls on both agents on the system bus. DEFER# (I - AGTL) The DEFER# (Defer) signal is asserted by an agent to indicate that the transaction cannot be guaranteed in-order completion. Assertion of DEFER# is normally the responsibility of the addressed memory agent or I/O agent. This signal must be connected to the appropriate pins/balls on both agents on the system bus. DEP[7:0]# (I/O - AGTL) The DEP[7:0]# (Data Bus ECC Protection) signals provide optional ECC protection for the data bus. They are driven by the agent responsible for driving D[63:0]#, and must be connected to the appropriate pins/balls on both agents on the system bus if they are used. During power-on configuration, DEP[7:0]# signals can be enabled for ECC checking or disabled for no checking. DRDY# (I/O - AGTL) The DRDY# (Data Ready) signal is asserted by the data driver on each data transfer, indicating valid data on the data bus. In a multi-cycle data transfer, DRDY# can be deasserted to insert idle clocks. This signal must be connected to the appropriate pins/balls on both agents on the system bus. DPSLP# (I - 1.5V Tolerant) The DPSLP# (Deep Sleep) signal, when asserted in the Quick Start state, causes the processor to enter the Deep Sleep state. In order to return to the Quick Start state BCLK must be running and the DPSLP# pin must be deasserted. EDGCTRLP (I-Analog) The EDGCTRLP (Edge Rate Control) signal is used to configure the edge rate of the AGTL output buffers. Connect the signal to VSS with a 110-, 1% resistor. FERR# (O - 1.5V Tolerant Open-drain) The FERR# (Floating-point Error) signal is asserted when the processor detects an unmasked floatingpoint error. FERR# is similar to the ERROR# signal on the Intel 387 co-processor, and it is included for compatibility with systems using DOS-type floating-point error reporting. 64 Datasheet 298517-001 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet FLUSH# (I - 1.5V Tolerant) When the FLUSH# (Flush) input signal is asserted, the processor writes back all internal cache lines in the Modified state and invalidates all internal cache lines. At the completion of a flush operation, the processor issues a Flush Acknowledge transaction. The processor stops caching any new data while the FLUSH# signal remains asserted. On the active-to-inactive transition of RESET#, each processor bus agent samples FLUSH# to determine its power-on configuration. HIT# (I/O - AGTL), HITM# (I/O - AGTL) The HIT# (Snoop Hit) and HITM# (Hit Modified) signals convey transaction snoop operation results, and must be connected to the appropriate pins/balls on both agents on the system bus. Either bus agent can assert both HIT# and HITM# together to indicate that it requires a snoop stall, which can be continued by reasserting HIT# and HITM# together. IERR# (O - 1.5V Tolerant Open-drain) The IERR# (Internal Error) signal is asserted by the processor as the result of an internal error. Assertion of IERR# is usually accompanied by a SHUTDOWN transaction on the system bus. This transaction may optionally be converted to an external error signal (e.g., NMI) by system logic. The processor will keep IERR# asserted until it is handled in software or with the assertion of RESET#, BINIT, or INIT#. IGNNE# (I - 1.5V Tolerant) The IGNNE# (Ignore Numeric Error) signal is asserted to force the processor to ignore a numeric error and continue to execute non-control floating-point instructions. If IGNNE# is deasserted, the processor freezes on a non-control floating-point instruction if a previous instruction caused an error. IGNNE# has no affect when the NE bit in control register 0 (CR0) is set. INIT# (I - 1.5V Tolerant) The INIT# (Initialization) signal is asserted to reset integer registers inside the processor without affecting the internal (L1 or L2) caches or the floating-point registers. The processor begins execution at the power-on reset vector configured during power-on configuration. The processor continues to handle snoop requests during INIT# assertion. INIT# is an asynchronous input. If INIT# is sampled active on RESET#'s active-to-inactive transition, then the processor executes its built-in self test (BIST). INTR (I - 1.5V Tolerant) The INTR (Interrupt) signal indicates that an external interrupt has been generated. INTR becomes the LINT0 signal when the APIC is enabled. The interrupt is maskable using the IF bit in the EFLAGS register. If the IF bit is set, the processor vectors to the interrupt handler after completing the current instruction execution. Upon recognizing the interrupt request, the processor issues a single Interrupt Acknowledge (INTA) bus transaction. INTR must remain active until the INTA bus transaction to guarantee its recognition. 298517-001 Datasheet 65 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet LINT[1:0] (I - 1.5V Tolerant) The LINT[1:0] (Local APIC Interrupt) signals must be connected to the appropriate pins/balls of all APIC bus agents, including the processor and the system logic or I/O APIC component. When APIC is disabled, the LINT0 signal becomes INTR, a maskable interrupt request signal, and LINT1 becomes NMI, a non-maskable interrupt. INTR and NMI are backward compatible with the same signals for the Pentium processor. Both signals are asynchronous inputs. Both of these signals must be software configured by programming the APIC register space to be used either as NMI/INTR or LINT[1:0] in the BIOS. If the APIC is enabled at reset, then LINT[1:0] is the default configuration. LOCK# (I/O - AGTL) The LOCK# (Lock) signal indicates to the system that a sequence of transactions must occur atomically. This signal must be connected to the appropriate pins/balls on both agents on the system bus. For a locked sequence of transactions, LOCK# is asserted from the beginning of the first transaction through the end of the last transaction. When the priority agent asserts BPRI# to arbitrate for bus ownership, it waits until it observes LOCK# deasserted. This enables the processor to retain bus ownership throughout the bus locked operation and guarantee the atomicity of lock. NCTRL (I - Analog) The NCTRL signal provides the AGTL pull down impedance control. The processor samples this input to determine the N-channel pull-down device strength when it is the driving agent. An external 14 ohm (1% tolerance) pull-up resistor to VCCT is required for this signal. Please refer to platform design guide for implementation details. NMI (I - 1.5V Tolerant) The NMI (Non-Maskable Interrupt) indicates that an external interrupt has been generated. NMI becomes the LINT1 signal when the APIC is disabled. Asserting NMI causes an interrupt with an internally supplied vector value of 2. An external interrupt-acknowledge transaction is not generated. If NMI is asserted during the execution of an NMI service routine, it remains pending and is recognized after the IRET is executed by the NMI service routine. At most, one assertion of NMI is held pending. NMI is rising edge sensitive. PICCLK (I - 1.8V Tolerant) The PICCLK (APIC Clock) signal is an input clock to the processor and system logic or I/O APIC that is required for operation of the processor, system logic, and I/O APIC components on the APIC bus. PICD[1:0] (I/O - 1.5V Tolerant Open-drain) The PICD[1:0] (APIC Data) signals are used for bi-directional serial message passing on the APIC bus. They must be connected to the appropriate pins/balls of all APIC bus agents, including the processor and the system logic or I/O APIC components. If the PICD0 signal is sampled low on the active-to-inactive transition of the RESET# signal, then the APIC is hardware disabled. For the Mobile Intel Celeron Processor, the APIC is required to be hardware enabled as described in Section 7.1.3. 66 Datasheet 298517-001 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet PLL1, PLL2 (Analog) The PLL1 and PLL2 signals provide isolated analog decoupling is required for the internal PLL. See Section 3.2.2 for a description of the analog decoupling circuit. PRDY# (O - AGTL) The PRDY# (Probe Ready) signal is a processor output used by debug tools to determine processor debug readiness. PREQ# (I - 1.5V Tolerant) The PREQ# (Probe Request) signal is used by debug tools to request debug operation of the processor. PWRGOOD (I - 1.8V Tolerant) PWRGOOD (Power Good) is a 1.8-V tolerant input. The processor requires this signal to be a clean indication that clocks and the power supplies (VCC, VCCT, etc.) are stable and within their specifications. Clean implies that the signal will remain low, (capable of sinking leakage current) and without glitches, from the time that the power supplies are turned on, until they come within specification. The signal will then transition monotonically to a high (1.8V) state. Figure 10 through Figure 12 illustrate the relationship of PWRGOOD to other system signals. PWRGOOD can be driven inactive at any time, but clocks and power must again be stable before the rising edge of PWRGOOD. It must also meet the minimum pulse width specified in. Table 18 (Section 3.6) and be followed by a 1 ms RESET# pulse. PWRGOOD may be asserted before BCLK is active (see Table 18, Note 5) The PWRGOOD signal, which must be supplied to the processor, is used to protect internal circuits against voltage sequencing issues. The PWRGOOD signal should be driven high throughout boundary scan operation. REQ[4:0]# (I/O - AGTL) The REQ[4:0]# (Request Command) signals must be connected to the appropriate pins/balls on both agents on the system bus. They are asserted by the current bus owner when it drives A[35:3]# to define the currently active transaction type. RESET# (I - AGTL) Asserting the RESET# signal resets the processor to a known state and invalidates the L1 and L2 caches without writing back Modified (M state) lines. For a power-on type reset, RESET# must stay active for at least 1 ms after VCC and BCLK have reached their proper DC and AC specifications and after PWRGOOD has been asserted. When observing active RESET#, all bus agents will deassert their outputs within two clocks. RESET# is the only AGTL signal that does not have on-die AGTL termination. A 56.2 1% terminating resistor connected to VCCT is required. A number of bus signals are sampled at the active-to-inactive transition of RESET# for the power-on configuration. The configuration options are described in Section 4 and in the P6 Family of Processors Developer's Manual. 298517-001 Datasheet 67 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet Unless its outputs are tri-stated during power-on configuration, after an active-to-inactive transition of RESET#, the processor optionally executes its built-in self-test (BIST) and begins program execution at reset-vector 000FFFF0H or FFFFFFF0H. RESET# must be connected to the appropriate pins/balls on both agents on the system bus. RP# (I/O - AGTL) The RP# (Request Parity) signal is driven by the request initiator and provides parity protection on ADS# and REQ[4:0]#. RP# should be connected to the appropriate pins/balls on both agents on the system bus. A correct parity signal is high if an even number of covered signals is low and low if an odd number of covered signals are low. This definition allows parity to be high when all covered signals are high. RS[2:0]# (I/O - AGTL) The RS[2:0]# (Response Status) signals are driven by the response agent (the agent responsible for completion of the current transaction) and must be connected to the appropriate pins/balls on both agents on the system bus. RSP# (I - AGTL) The RSP# (Response Parity) signal is driven by the response agent (the agent responsible for completion of the current transaction) during assertion of RS[2:0]#. RSP# provides parity protection for RS[2:0]#. RSP# should be connected to the appropriate pins/balls on both agents on the system bus. A correct parity signal is high if an even number of covered signals are low, and it is low if an odd number of covered signals are low. During Idle state of RS[2:0]# (RS[2:0]#=000), RSP# is also high since it is not driven by any agent guaranteeing correct parity. RTTIMPEDP (I-Analog) The RTTIMPEDP (RTT Impedance/PMOS) signal is used to configure the on-die AGTL termination. Connect the RTTIMPEDP signal to VSS with a 56.2-, 1% resistor. SMI# (I - 1.5V Tolerant) The SMI# (System Management Interrupt) is asserted asynchronously by system logic. On accepting a System Management Interrupt, the processor saves the current state and enters System Management Mode (SMM). An SMI Acknowledge transaction is issued, and the processor begins program execution from the SMM handler. STPCLK# (I - 1.5V Tolerant) The STPCLK# (Stop Clock) signal, when asserted, causes the processor to enter a low-power Quick Start state. The processor issues a Stop Grant Acknowledge special transaction and stops providing internal clock signals to all units except the bus and APIC units. The processor continues to snoop bus transactions and service interrupts while in the Quick Start state. When STPCLK# is deasserted and other conditions in are met, the processor restarts its internal clock to all units and resumes execution. The assertion of STPCLK# has no affect on the bus clock. 68 Datasheet 298517-001 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet TCK (I - 1.5V Tolerant) The TCK (Test Clock) signal provides the clock input for the test bus (also known as the test access port). TDI (I - 1.5V Tolerant) The TDI (Test Data In) signal transfers serial test data to the processor. TDI provides the serial input needed for JTAG support. TDO (O - 1.5V Tolerant Open-drain) The TDO (Test Data Out) signal transfers serial test data from the processor. TDO provides the serial output needed for JTAG support. TESTHI[2:1] (I - 1.25V Tolerant) The TESTHI[2:1] (Test input High) signals are used during processor test and need to be pulled high during normal operation. TESTLO[2:1] (I - 1.5V Tolerant) The TESTLO[2:1] (Test input Low) signals are used during processor test and needs to be pulled to ground during normal operation. THERMDA, THERMDC (Analog) The THERMDA (Thermal Diode Anode) and THERMDC (Thermal Diode Cathode) signals connect to the anode and cathode of the on-die thermal diode. TMS (I - 1.5V Tolerant) The TMS (Test Mode Select) signal is a JTAG support signal used by debug tools. TRDY# (I/O - AGTL) The TRDY# (Target Ready) signal is asserted by the target to indicate that the target is ready to receive write or implicit write-back data transfer. TRDY# must be connected to the appropriate pins/balls on both agents on the system bus. TRST# (I - 1.5V Tolerant) The TRST# (Test Reset) signal resets the Test Access Port (TAP) logic. The Mobile Intel Celeron Processors do not self-reset during power on; therefore, it is necessary to drive this signal low during power-on reset. VID[4:0] (O - Open-drain) The VID[4:0] (Voltage ID) pins/balls can be used to support automatic selection of power supply voltages. Please refer to Section 3.2.3 for details. 298517-001 Datasheet 69 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet VREF (Analog) The VREF (AGTL Reference Voltage) signal provides a DC level reference voltage for the AGTL input buffers. A voltage divider should be used to divide VCCT by 2/3. Resistor values of 1.00 k and 2.00 k are recommended. Decouple the VREF signal with three 0.1-F high-frequency capacitors close to the processor. VTTPWRGD (I - 1.25V) The VTTPWRGD signal informs the processor to output the VID signals. During power up, the VID signals will be in an indeterminate state for a small period of time. The voltage regulator should not sample and/or latch the VID signals until the VTTPWRGD signal is asserted. The assertion of the VTTPWRGD signal indicates that the VID signals are stable and are driven to the final state by the processor. Please refer to Figure 10 for the power up sequence. 70 Datasheet 298517-001 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet 8.2 Signal Summaries Table 35. Input Signals Name Active Level Clock Signal Group Qualified A20M# Low Asynch CMOS Always BCLK High -- System Bus Always BPRI# Low BCLK System Bus Always DEFER# Low BCLK System Bus Always FLUSH# Low Asynch CMOS Always IGNNE# Low Asynch CMOS Always INIT# Low Asynch System Bus Always INTR High Asynch CMOS APIC disabled mode LINT[1:0] High Asynch APIC APIC enabled mode CMOS APIC disabled mode NMI High Asynch NCTRL High Asynch PICCLK High -- APIC Always PREQ# Low Asynch Implementation Always PWRGOOD High Asynch Implementation Always RESET# Low BCLK System Bus Always RSP# Low BCLK System Bus Always BSEL[1:0] High Asynch Implementation Always DPSLP# Low Asynch Implementation Quick Start state SMI# Low Asynch CMOS Always STPCLK# Low Asynch Implementation Always TCK High -- JTAG TDI TCK JTAG TMS TCK JTAG TRST# Low Asynch JTAG VTTPWRGD High Asynch Power/Other Table 36. Output Signals 298517-001 Name Active Level Clock Signal Group BSEL[1:0] High Asynch Open-drain FERR# Low Asynch Open-drain IERR# Low Asynch Open-drain PRDY# Low BCLK Implementation TDO High TCK JTAG VID[4:0] High Asynch Power/Other Datasheet 71 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet Table 37. Input/Output Signals (Single Driver) Name Active Level Clock Signal Group Qualified A[35:3]# Low BCLK System Bus ADS#, ADS#+1 ADS# Low BCLK System Bus Always AP[1:0]# Low BCLK System Bus ADS#, ADS#+1 BREQ0# Low BCLK System Bus Always BP[3:2]# Low BCLK System Bus Always BPM[1:0]# Low BCLK System Bus Always D[63:0]# Low BCLK System Bus DRDY# DBSY# Low BCLK System Bus Always DEP[7:0]# Low BCLK System Bus DRDY# DRDY# Low BCLK System Bus Always LOCK# Low BCLK System Bus Always REQ[4:0]# Low BCLK System Bus ADS#, ADS#+1 RP# Low BCLK System Bus ADS#, ADS#+1 RS[2:0]# Low BCLK System Bus Always TRDY# Low BCLK System Bus Response phase Table 38. Input/Output Signals (Multiple Driver) 72 Name Active Level Clock Signal Group Qualified AERR# Low BCLK System Bus ADS#+3 BERR# Low BCLK System Bus Always BINIT# Low BCLK System Bus Always BNR# Low BCLK System Bus Always HIT# Low BCLK System Bus Always HITM# Low BCLK System Bus Always PICD[1:0] High PICCLK APIC Always Datasheet 298517-001 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet Appendix A. PLL RLC Filter Specification A1. Introduction All Mobile Intel Celeron Processors have internal PLL clock generators, which are analog in nature and require quiet power supplies for minimum jitter. Jitter is detrimental to a system; it degrades external I/O timings as well as internal core timings (i.e. maximum frequency). The PLL RLC filter specifications for the Mobile Intel Celeron Processor are the same as those for the mobile Intel Pentium III-M processor. The general desired topology is shown in Figure 2. Excluded from the external circuitry are parasitics associated with each component. A2. Filter Specification The function of the filter is two fold. It protects the PLL from external noise through low-pass attenuation. It also protects the PLL from internal noise through high-pass filtering. In general, the lowpass description forms an adequate description for the filter. The AC low-pass specification, with input at VCCT and output measured across the capacitor, is as follows: * < 0.2-dB gain in pass band * < 0.5-dB attenuation in pass band < 1 Hz (see DC drop in next set of requirements) * 34-dB attenuation from 1 MHz to 66 MHz * 28-dB attenuation from 66 MHz to core frequency * The filter specification (AC) is graphically shown in Figure 23. Other requirements: 298517-001 * Use a shielded type inductor to minimize magnetic pickup * The filter should support a DC current of at least 30 mA * The DC voltage drop from VCCT to PLL1 should be less than 60 mV, which in practice implies series resistance of less than 2. This also means that the pass band (from DC to 1 Hz) attenuation below 0.43 dB for VCCT = 1.25V. Datasheet 73 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet Figure 23. PLL Filter Specifications 0.2 dB 0 dB x dB forbidden zone -28 dB forbidden zone -34 dB 1 Hz DC fpeak 1 MHz 66 MHz fcore high frequency band passband x = 20.log[(Vcct-60 mV)/ Vcct] NOTES: Diagram is not to scale No specification for frequencies beyond fcore. Fpeak, if existent, should be less than 0.05 MHz. A3. Recommendation for Mobile Systems The following LC components are recommended. The tables will be updated as other suitable components and specifications are identified. Table 39. PLL Filter Inductor Recommendations Inductor Part Number Value Tol SRF Rated I 4.7 H 10% 35 MHz 30 mA DCR Min Damping R Needed 0.56 (1 max) 0 L1 TDK MLF2012A4R7KT L2 Murata LQG21N4R7K10 4.7 H 10% 47 MHz 30 mA 0.7 (+/-50%) L3 Murata LQG21C4R7N00 4.7 H 30% 35 MHz 30 mA 0.3 max NOTE: 0 0.2 (assumed) Minimum damping resistance is calculated from 0.35 - DCRmin. From vendor provided data, L1 and L2 DCRmin is 0.4 and 0.5 respectively, qualifying them for zero required trace resistance. DCRmin for L3 is not known and is assumed to be 0.15. Products with equivalent specifications may also be used. Table 40. PLL Filter Capacitor Recommendations Capacitor 74 Part Number Value Tolerance ESL ESR C1 Kemet T495D336M016AS 33 F 20% 2.5 nH 0.225 C2 AVX TPSD336M020S0200 33 F 20% unknown 0.2 Datasheet 298517-001 (R) (R) Mobile Intel Celeron Processor (0.13) in Micro-FCBGA Package Datasheet Table 41. PLL Filter Resistor Recommendations Resistor Part Number Value Tolerance Power R1 Various 1 10% 1/16W To satisfy damping requirements, total series resistance in the filter (from VCCT to the top plate of the capacitor) must be at least 0.35. This resistor can be in the form of a discrete component, or routing, or both. For example, if the picked inductor has minimum DCR of 0.25, then a routing resistance of at least 0.10 is required. Be careful not to exceed the maximum resistance rule (2). For example, if using discrete R1, the maximum DCR of the L should be less than 2.0 - 1.1 = 0.9, which precludes using L2 and possibly L1. Other routing requirements include: A4. 298517-001 * The capacitor should be close to the PLL1 and PLL2 pins, with less than 0.1 per route (These routes do not count towards the minimum damping resistance requirement). * The PLL2 route should be parallel and next to the PLL1 route (minimize loop area). * The inductor should be close to the capacitor; any routing resistance should be inserted between VCCT and the inductor. * Any discrete resistor should be inserted between VCCT and the inductor. Comments * A magnetically shielded inductor protects the circuit from picking up external flux noise. This should provide better timing margins than with an unshielded inductor. * A discrete or routed resistor is required because the LC filter by nature has an under-damped response, which can cause resonance at the LC pole. Noise amplification at this band, although not in the PLL-sensitive spectrum, could cause a fatal headroom reduction for analog circuitry. The resistor serves to dampen the response. Systems with tight space constraints should consider a discrete resistor to provide the required damping resistance. Too large of a damping resistance can cause a large IR drop, which means less analog headroom and lower frequency. * Ceramic capacitors have very high self-resonance frequencies, but they are not available in large capacitance values. A high self-resonant frequency coupled with low ESL/ESR is crucial for sufficient rejection in the PLL and high frequency band. The recommended tantalum capacitors have acceptably low ESR and ESL. * The capacitor must be close to the PLL1 and PLL2 pins; otherwise the value of the low ESR tantalum capacitor is wasted. Note the distance constraint should be translated from the 0.1- requirement. Datasheet 75