LM2734Z www.ti.com SNVS334E - JANUARY 2005 - REVISED APRIL 2013 LM2734Z/LM2734ZQ Thin SOT 1A Load Step-Down DC-DC Regulator Check for Samples: LM2734Z FEATURES DESCRIPTION * The LM2734Z regulator is a monolithic, high frequency, PWM step-down DC/DC converter assembled in a 6-pin Thin SOT and WSON non pull back package. It provides all the active functions to provide local DC/DC conversion with fast transient response and accurate regulation in the smallest possible PCB area. 1 23 * * * * * * * * * * * Thin SOT-6 Package, or 6 Lead WSON Package 3.0V to 20V Input Voltage Range 0.8V to 18V Output Voltage Range 1A Output Current 3MHz Switching Frequency 300m NMOS Switch 30nA Shutdown Current 0.8V, 2% Internal Voltage Reference Internal Soft-Start Current-Mode, PWM Operation Thermal Shutdown LM2734ZQ is AEC-Q100 Grade 1 Qualified and is Manufactured on an Automotive Grade Flow APPLICATIONS * * * * * DSL Modems Local Point of Load Regulation Battery Powered Devices USB Powered Devices Automotive With a minimum of external components and online design support through WEBENCHTM, the LM2734Z is easy to use. The ability to drive 1A loads with an internal 300m NMOS switch using state-of-the-art 0.5m BiCMOS technology results in the best power density available. The world class control circuitry allows for on-times as low as 13ns, thus supporting exceptionally high frequency conversion over the entire 3V to 20V input operating range down to the minimum output voltage of 0.8V. Switching frequency is internally set to 3MHz, allowing the use of extremely small surface mount inductors and chip capacitors. Even though the operating frequency is very high, efficiencies up to 85% are easy to achieve. External shutdown is included, featuring an ultra-low stand-by current of 30nA. The LM2734Z utilizes current-mode control and internal compensation to provide high-performance regulation over a wide range of operating conditions. Additional features include internal soft-start circuitry to reduce inrush current, pulse-by-pulse current limit, thermal shutdown, and output over-voltage protection. 1 2 3 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. WEBENCH is a trademark of Texas Instruments, Inc.. All other trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2005-2013, Texas Instruments Incorporated LM2734Z SNVS334E - JANUARY 2005 - REVISED APRIL 2013 www.ti.com Typical Application Circuit Efficiency vs Load Current VIN = 5V, VOUT = 3.3V D2 VIN BOOST VIN C3 C1 L1 SW VOUT LM2734 ON D1 EN C2 R1 OFF FB GND R2 Connection Diagrams BOOST 1 6 SW FB 1 GND 2 5 VIN GND 2 FB 3 4 EN BOOST 3 Figure 1. 6-Lead SOT See Package Number DDC (R-PDSO-G6) DAP 6 EN 5 VIN 4 SW Figure 2. 6-Lead WSON (3mm x 3mm) See Package Number NGG0006A PIN DESCRIPTIONS Pin Name 1 BOOST Boost voltage that drives the internal NMOS control switch. A bootstrap capacitor is connected between the BOOST and SW pins. Function 2 GND Signal and Power ground pin. Place the bottom resistor of the feedback network as close as possible to this pin for accurate regulation. 3 FB Feedback pin. Connect FB to the external resistor divider to set output voltage. 4 EN Enable control input. Logic high enables operation. Do not allow this pin to float or be greater than VIN + 0.3V. 5 VIN Input supply voltage. Connect a bypass capacitor to this pin. 6 SW Output switch. Connects to the inductor, catch diode, and bootstrap capacitor. DAP GND The Die Attach Pad is internally connected to GND These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. 2 Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM2734Z LM2734Z www.ti.com SNVS334E - JANUARY 2005 - REVISED APRIL 2013 Absolute Maximum Ratings (1) (2) VIN -0.5V to 24V SW Voltage -0.5V to 24V Boost Voltage -0.5V to 30V Boost to SW Voltage -0.5V to 6.0V FB Voltage -0.5V to 3.0V EN Voltage -0.5V to (VIN + 0.3V) Junction Temperature ESD Susceptibility 150C (3) 2kV Storage Temp. Range Soldering Information (1) (2) (3) -65C to 150C Infrared/Convection Reflow (15sec) 220C Wave Soldering Lead Temp. (10sec) 260C Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but specific performance is not ensured. For specific specifications and the test conditions, see Electrical Characteristics. If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and specifications. Human body model, 1.5k in series with 100pF. Operating Ratings (1) VIN 3V to 20V SW Voltage -0.5V to 20V Boost Voltage -0.5V to 25V Boost to SW Voltage 1.6V to 5.5V -40C to +125C Junction Temperature Range Thermal Resistance JA (2) (1) (2) SOT-6 118C/W Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but specific performance is not ensured. For specific specifications and the test conditions, see Electrical Characteristics. Thermal shutdown will occur if the junction temperature exceeds 165C. The maximum power dissipation is a function of TJ(MAX) , JA and TA . The maximum allowable power dissipation at any ambient temperature is PD = (TJ(MAX) - TA)/JA . All numbers apply for packages soldered directly onto a 3" x 3" PC board with 2oz. copper on 4 layers in still air. For a 2 layer board using 1 oz. copper in still air, JA = 204C/W. Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM2734Z 3 LM2734Z SNVS334E - JANUARY 2005 - REVISED APRIL 2013 www.ti.com Electrical Characteristics Specifications with standard typeface are for TJ = 25C, and those in boldface type apply over the full Operating Temperature Range (TJ = -40C to 125C). VIN = 5V, VBOOST - VSW = 5V unless otherwise specified. Datasheet min/max specification limits are specified by design, test, or statistical analysis. Symbol VFB VFB/VIN IFB UVLO Feedback Voltage Feedback Voltage Line Regulation VIN = 3V to 20V Feedback Input Bias Current Sink/Source Undervoltage Lockout VIN Rising Undervoltage Lockout VIN Falling Min (1) Typ (2) Max (1) Units 0.784 0.800 0.816 V 0.01 %/V 10 250 2.74 2.90 2.0 2.3 nA V UVLO Hysteresis 0.30 0.44 0.62 Switching Frequency 2.2 3.0 3.6 DMAX Maximum Duty Cycle 78 85 % DMIN Minimum Duty Cycle 8 % Switch ON Resistance 300 600 m VBOOST - VSW = 3V (WSON Package) 340 650 m 1.7 2.5 A 1.5 2.5 mA 6 mA Switch Current Limit VBOOST - VSW = 3V IQ Quiescent Current Switching Quiescent Current (shutdown) VEN = 0V Boost Pin Current (Switching) Shutdown Threshold Voltage VEN Falling Enable Threshold Voltage VEN Rising IEN Enable Pin Current Sink/Source ISW Switch Leakage VEN_TH MHz VBOOST - VSW = 3V (SOT Package) ICL IBOOST 4 Conditions FSW RDS(ON) (1) (2) Parameter 1.2 30 4.25 nA 0.4 1.8 V 10 nA 40 nA Specified to Texas Instruments' Average Outgoing Quality Level (AOQL). Typicals represent the most likely parametric norm. Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM2734Z LM2734Z www.ti.com SNVS334E - JANUARY 2005 - REVISED APRIL 2013 Typical Performance Characteristics All curves taken at VIN = 5V, VBOOST - VSW = 5V, L1 = 2.2 H and TA = 25C, unless specified otherwise. Efficiency vs Load Current VOUT = 5V Efficiency vs Load Current VOUT = 3.3V Figure 3. Figure 4. Efficiency vs Load Current VOUT = 1.5V Oscillator Frequency vs Temperature Figure 5. Figure 6. Line Regulation VOUT = 1.5V, IOUT = 500mA Line Regulation VOUT = 3.3V, IOUT = 500mA Figure 7. Figure 8. Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM2734Z 5 LM2734Z SNVS334E - JANUARY 2005 - REVISED APRIL 2013 www.ti.com Block Diagram VIN VIN Current-Sense Amplifier OFF EN Internal Regulator and Enable Circuit RSENSE + - CIN D2 Thermal Shutdown BOOST VBOOST Under Voltage Lockout Current Limit Oscillator Output Control Logic Reset Pulse + ISENSE + + Corrective Ramp 0.3: Switch Driver SW OVP Comparator - ON Error Signal D 1 + PWM Comparator CBOOST VSW L IL VOUT COUT 0.88V + - R 1 FB Internal Compensation + Error Amplifier + - VREF 0.8V R 2 GND APPLICATION INFORMATION THEORY OF OPERATION The LM2734Z is a constant frequency PWM buck regulator IC that delivers a 1A load current. The regulator has a preset switching frequency of 3MHz. This high frequency allows the LM2734Z to operate with small surface mount capacitors and inductors, resulting in a DC/DC converter that requires a minimum amount of board space. The LM2734Z is internally compensated, so it is simple to use, and requires few external components. The LM2734Z uses current-mode control to regulate the output voltage. The following operating description of the LM2734Z will refer to the Simplified Block Diagram (Block Diagram) and to the waveforms in Figure 9. The LM2734Z supplies a regulated output voltage by switching the internal NMOS control switch at constant frequency and variable duty cycle. A switching cycle begins at the falling edge of the reset pulse generated by the internal oscillator. When this pulse goes low, the output control logic turns on the internal NMOS control switch. During this on-time, the SW pin voltage (VSW) swings up to approximately VIN, and the inductor current (IL) increases with a linear slope. IL is measured by the current-sense amplifier, which generates an output proportional to the switch current. The sense signal is summed with the regulator's corrective ramp and compared to the error amplifier's output, which is proportional to the difference between the feedback voltage and VREF. When the PWM comparator output goes high, the output switch turns off until the next switching cycle begins. During the switch off-time, inductor current discharges through Schottky diode D1, which forces the SW pin to swing below ground by the forward voltage (VD) of the catch diode. The regulator loop adjusts the duty cycle (D) to maintain a constant output voltage. 6 Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM2734Z LM2734Z www.ti.com SNVS334E - JANUARY 2005 - REVISED APRIL 2013 VSW D = TON/TSW VIN SW Voltage TOFF TON 0 VD t TSW IL IPK Inductor Current t 0 Figure 9. LM2734Z Waveforms of SW Pin Voltage and Inductor Current BOOST FUNCTION Capacitor CBOOST and diode D2 in Figure 10 are used to generate a voltage VBOOST. VBOOST - VSW is the gate drive voltage to the internal NMOS control switch. To properly drive the internal NMOS switch during its on-time, VBOOST needs to be at least 1.6V greater than VSW. Although the LM2734Z will operate with this minimum voltage, it may not have sufficient gate drive to supply large values of output current. Therefore, it is recommended that VBOOST be greater than 2.5V above VSW for best efficiency. VBOOST - VSW should not exceed the maximum operating limit of 5.5V. 5.5V > VBOOST - VSW > 2.5V for best performance. VBOOST D2 BOOST VIN VIN LM2734 CIN CBOOST L SW VOUT GND D1 COUT Figure 10. VOUT Charges CBOOST When the LM2734Z starts up, internal circuitry from the BOOST pin supplies a maximum of 20mA to CBOOST. This current charges CBOOST to a voltage sufficient to turn the switch on. The BOOST pin will continue to source current to CBOOST until the voltage at the feedback pin is greater than 0.76V. There are various methods to derive VBOOST: 1. From the input voltage (VIN) 2. From the output voltage (VOUT) 3. From an external distributed voltage rail (VEXT) 4. From a shunt or series zener diode Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM2734Z 7 LM2734Z SNVS334E - JANUARY 2005 - REVISED APRIL 2013 www.ti.com In the Simplifed Block Diagram of Block Diagram, capacitor CBOOST and diode D2 supply the gate-drive current for the NMOS switch. Capacitor CBOOST is charged via diode D2 by VIN. During a normal switching cycle, when the internal NMOS control switch is off (TOFF) (refer to Figure 9), VBOOST equals VIN minus the forward voltage of D2 (VFD2), during which the current in the inductor (L) forward biases the Schottky diode D1 (VFD1). Therefore the voltage stored across CBOOST is VBOOST - VSW = VIN - VFD2 + VFD1 (1) When the NMOS switch turns on (TON), the switch pin rises to VSW = VIN - (RDSON x IL), (2) forcing VBOOST to rise thus reverse biasing D2. The voltage at VBOOST is then VBOOST = 2VIN - (RDSON x IL) - VFD2 + VFD1 (3) which is approximately 2VIN - 0.4V (4) for many applications. Thus the gate-drive voltage of the NMOS switch is approximately VIN - 0.2V (5) An alternate method for charging CBOOST is to connect D2 to the output as shown in Figure 10. The output voltage should be between 2.5V and 5.5V, so that proper gate voltage will be applied to the internal switch. In this circuit, CBOOST provides a gate drive voltage that is slightly less than VOUT. In applications where both VIN and VOUT are greater than 5.5V, or less than 3V, CBOOST cannot be charged directly from these voltages. If VIN and VOUT are greater than 5.5V, CBOOST can be charged from VIN or VOUT minus a zener voltage by placing a zener diode D3 in series with D2, as shown in Figure 11. When using a series zener diode from the input, ensure that the regulation of the input supply doesn't create a voltage that falls outside the recommended VBOOST voltage. (VINMAX - VD3) < 5.5V (VINMIN - VD3) > 1.6V (6) (7) D2 D3 VIN VIN CIN BOOST VBOOST CBOOST LM2734 L VOUT SW GND D1 C OUT Figure 11. Zener Reduces Boost Voltage from VIN An alternative method is to place the zener diode D3 in a shunt configuration as shown in Figure 12. A small 350mW to 500mW 5.1V zener in a SOT or SOD package can be used for this purpose. A small ceramic capacitor such as a 6.3V, 0.1F capacitor (C4) should be placed in parallel with the zener diode. When the internal NMOS switch turns on, a pulse of current is drawn to charge the internal NMOS gate capacitance. The 0.1 F parallel shunt capacitor ensures that the VBOOST voltage is maintained during this time. Resistor R3 should be chosen to provide enough RMS current to the zener diode (D3) and to the BOOST pin. A recommended choice for the zener current (IZENER) is 1 mA. The current IBOOST into the BOOST pin supplies the gate current of the NMOS control switch and varies typically according to the following formula: IBOOST = (D + 0.5) x (VZENER - VD2) mA (8) where D is the duty cycle, VZENER and VD2 are in volts, and IBOOST is in milliamps. VZENER is the voltage applied to the anode of the boost diode (D2), and VD2 is the average forward voltage across D2. Note that this formula for IBOOST gives typical current. For the worst case IBOOST, increase the current by 25%. In that case, the worst case boost current will be IBOOST-MAX = 1.25 x IBOOST 8 (9) Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM2734Z LM2734Z www.ti.com SNVS334E - JANUARY 2005 - REVISED APRIL 2013 R3 will then be given by R3 = (VIN - VZENER) / (1.25 x IBOOST + IZENER) (10) For example, let VIN = 10V, VZENER = 5V, VD2 = 0.7V, IZENER = 1mA, and duty cycle D = 50%. Then IBOOST = (0.5 + 0.5) x (5 - 0.7) mA = 4.3mA R3 = (10V - 5V) / (1.25 x 4.3mA + 1mA) = 787 (11) (12) VZ C4 D2 D3 R3 BOOST VIN VIN C IN VBOOST CBOOST LM2734 L SW VOUT GND D1 COUT Figure 12. Boost Voltage Supplied from the Shunt Zener on VIN ENABLE PIN / SHUTDOWN MODE The LM2734Z has a shutdown mode that is controlled by the enable pin (EN). When a logic low voltage is applied to EN, the part is in shutdown mode and its quiescent current drops to typically 30nA. Switch leakage adds another 40nA from the input supply. The voltage at this pin should never exceed VIN + 0.3V. SOFT-START This function forces VOUT to increase at a controlled rate during start up. During soft-start, the error amplifier's reference voltage ramps from 0V to its nominal value of 0.8V in approximately 200s. This forces the regulator output to ramp up in a more linear and controlled fashion, which helps reduce inrush current. OUTPUT OVERVOLTAGE PROTECTION The overvoltage comparator compares the FB pin voltage to a voltage that is 10% higher than the internal reference Vref. Once the FB pin voltage goes 10% above the internal reference, the internal NMOS control switch is turned off, which allows the output voltage to decrease toward regulation. UNDERVOLTAGE LOCKOUT Undervoltage lockout (UVLO) prevents the LM2734Z from operating until the input voltage exceeds 2.74V(typ). The UVLO threshold has approximately 440mV of hysteresis, so the part will operate until VIN drops below 2.3V(typ). Hysteresis prevents the part from turning off during power up if VIN is non-monotonic. CURRENT LIMIT The LM2734Z uses cycle-by-cycle current limiting to protect the output switch. During each switching cycle, a current limit comparator detects if the output switch current exceeds 1.7A (typ), and turns off the switch until the next switching cycle begins. Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM2734Z 9 LM2734Z SNVS334E - JANUARY 2005 - REVISED APRIL 2013 www.ti.com THERMAL SHUTDOWN Thermal shutdown limits total power dissipation by turning off the output switch when the IC junction temperature exceeds 165C. After thermal shutdown occurs, the output switch doesn't turn on until the junction temperature drops to approximately 150C. Design Guide INDUCTOR SELECTION The Duty Cycle (D) can be approximated quickly using the ratio of output voltage (VO) to input voltage (VIN): VO D= VIN (13) The catch diode (D1) forward voltage drop and the voltage drop across the internal NMOS must be included to calculate a more accurate duty cycle. Calculate D by using the following formula: VO + VD D= VIN + VD - VSW (14) VSW can be approximated by: VSW = IO x RDS(ON) (15) The diode forward drop (VD) can range from 0.3V to 0.7V depending on the quality of the diode. The lower VD is, the higher the operating efficiency of the converter. The inductor value determines the output ripple current. Lower inductor values decrease the size of the inductor, but increase the output ripple current. An increase in the inductor value will decrease the output ripple current. The ratio of ripple current (iL) to output current (IO) is optimized when it is set between 0.3 and 0.4 at 1A. The ratio r is defined as: r= 'iL lO (16) One must also ensure that the minimum current limit (1.2A) is not exceeded, so the peak current in the inductor must be calculated. The peak current (ILPK) in the inductor is calculated by: ILPK = IO + IL/2 (17) If r = 0.5 at an output of 1A, the peak current in the inductor will be 1.25A. The minimum specified current limit over all operating conditions is 1.2A. One can either reduce r to 0.4 resulting in a 1.2A peak current, or make the engineering judgement that 50mA over will be safe enough with a 1.7A typical current limit and 6 sigma limits. When the designed maximum output current is reduced, the ratio r can be increased. At a current of 0.1A, r can be made as high as 0.9. The ripple ratio can be increased at lighter loads because the net ripple is actually quite low, and if r remains constant the inductor value can be made quite large. An equation empirically developed for the maximum ripple ratio at any current below 2A is: r = 0.387 x IOUT-0.3667 (18) Note that this is just a guideline. The LM2734Z operates at frequencies allowing the use of ceramic output capacitors without compromising transient response. Ceramic capacitors allow higher inductor ripple without significantly increasing output ripple. See the OUTPUT CAPACITOR section for more details on calculating output voltage ripple. Now that the ripple current or ripple ratio is determined, the inductance is calculated by: L= 10 VO + VD IO x r x fS x (1-D) (19) Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM2734Z LM2734Z www.ti.com SNVS334E - JANUARY 2005 - REVISED APRIL 2013 where fs is the switching frequency and IO is the output current. When selecting an inductor, make sure that it is capable of supporting the peak output current without saturating. Inductor saturation will result in a sudden reduction in inductance and prevent the regulator from operating correctly. Because of the speed of the internal current limit, the peak current of the inductor need only be specified for the required maximum output current. For example, if the designed maximum output current is 0.5A and the peak current is 0.7A, then the inductor should be specified with a saturation current limit of >0.7A. There is no need to specify the saturation or peak current of the inductor at the 1.7A typical switch current limit. The difference in inductor size is a factor of 5. Because of the operating frequency of the LM2734Z, ferrite based inductors are preferred to minimize core losses. This presents little restriction since the variety of ferrite based inductors is huge. Lastly, inductors with lower series resistance (DCR) will provide better operating efficiency. For recommended inductors see Example Circuits. INPUT CAPACITOR An input capacitor is necessary to ensure that VIN does not drop excessively during switching transients. The primary specifications of the input capacitor are capacitance, voltage, RMS current rating, and ESL (Equivalent Series Inductance). The recommended input capacitance is 10F, although 4.7F works well for input voltages below 6V. The input voltage rating is specifically stated by the capacitor manufacturer. Make sure to check any recommended deratings and also verify if there is any significant change in capacitance at the operating input voltage and the operating temperature. The input capacitor maximum RMS input current rating (IRMS-IN) must be greater than: IRMS-IN = IO x r2 D x 1-D + 12 (20) It can be shown from the above equation that maximum RMS capacitor current occurs when D = 0.5. Always calculate the RMS at the point where the duty cycle, D, is closest to 0.5. The ESL of an input capacitor is usually determined by the effective cross sectional area of the current path. A large leaded capacitor will have high ESL and a 0805 ceramic chip capacitor will have very low ESL. At the operating frequencies of the LM2734Z, certain capacitors may have an ESL so large that the resulting impedance (2fL) will be higher than that required to provide stable operation. As a result, surface mount capacitors are strongly recommended. Sanyo POSCAP, Tantalum or Niobium, Panasonic SP or Cornell Dubilier ESR, and multilayer ceramic capacitors (MLCC) are all good choices for both input and output capacitors and have very low ESL. For MLCCs it is recommended to use X7R or X5R dielectrics. Consult capacitor manufacturer datasheet to see how rated capacitance varies over operating conditions. OUTPUT CAPACITOR The output capacitor is selected based upon the desired output ripple and transient response. The initial current of a load transient is provided mainly by the output capacitor. The output ripple of the converter is: 'VO = 'iL x (RESR + 1 ) 8 x fS x CO (21) When using MLCCs, the ESR is typically so low that the capacitive ripple may dominate. When this occurs, the output ripple will be approximately sinusoidal and 90 phase shifted from the switching action. Given the availability and quality of MLCCs and the expected output voltage of designs using the LM2734Z, there is really no need to review any other capacitor technologies. Another benefit of ceramic capacitors is their ability to bypass high frequency noise. A certain amount of switching edge noise will couple through parasitic capacitances in the inductor to the output. A ceramic capacitor will bypass this noise while a tantalum will not. Since the output capacitor is one of the two external components that control the stability of the regulator control loop, most applications will require a minimum at 10 F of output capacitance. Capacitance can be increased significantly with little detriment to the regulator stability. Like the input capacitor, recommended multilayer ceramic capacitors are X7R or X5R. Again, verify actual capacitance at the desired operating voltage and temperature. Check the RMS current rating of the capacitor. The RMS current rating of the capacitor chosen must also meet the following condition: IRMS-OUT = IO x r 12 (22) Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM2734Z 11 LM2734Z SNVS334E - JANUARY 2005 - REVISED APRIL 2013 www.ti.com CATCH DIODE The catch diode (D1) conducts during the switch off-time. A Schottky diode is recommended for its fast switching times and low forward voltage drop. The catch diode should be chosen so that its current rating is greater than: ID1 = IO x (1-D) (23) The reverse breakdown rating of the diode must be at least the maximum input voltage plus appropriate margin. To improve efficiency choose a Schottky diode with a low forward voltage drop. BOOST DIODE A standard diode such as the 1N4148 type is recommended. For VBOOST circuits derived from voltages less than 3.3V, a small-signal Schottky diode is recommended for greater efficiency. A good choice is the BAT54 small signal diode. BOOST CAPACITOR A ceramic 0.01F capacitor with a voltage rating of at least 6.3V is sufficient. The X7R and X5R MLCCs provide the best performance. OUTPUT VOLTAGE The output voltage is set using the following equation where R2 is connected between the FB pin and GND, and R1 is connected between VO and the FB pin. A good value for R2 is 10k. R1 = VO VREF - 1 x R2 (24) PCB Layout Considerations When planning layout there are a few things to consider when trying to achieve a clean, regulated output. The most important consideration when completing the layout is the close coupling of the GND connections of the CIN capacitor and the catch diode D1. These ground ends should be close to one another and be connected to the GND plane with at least two through-holes. Place these components as close to the IC as possible. Next in importance is the location of the GND connection of the COUT capacitor, which should be near the GND connections of CIN and D1. There should be a continuous ground plane on the bottom layer of a two-layer board except under the switching node island. The FB pin is a high impedance node and care should be taken to make the FB trace short to avoid noise pickup and inaccurate regulation. The feedback resistors should be placed as close as possible to the IC, with the GND of R2 placed as close as possible to the GND of the IC. The VOUT trace to R1 should be routed away from the inductor and any other traces that are switching. High AC currents flow through the VIN, SW and VOUT traces, so they should be as short and wide as possible. However, making the traces wide increases radiated noise, so the designer must make this trade-off. Radiated noise can be decreased by choosing a shielded inductor. The remaining components should also be placed as close as possible to the IC. Please see Application Note AN-1229 for further considerations and the LM2734Z demo board as an example of a four-layer layout. Calculating Efficiency, and Junction Temperature The complete LM2734Z DC/DC converter efficiency can be calculated in the following manner. POUT K= PIN (25) Or POUT K= 12 POUT + PLOSS (26) Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM2734Z LM2734Z www.ti.com SNVS334E - JANUARY 2005 - REVISED APRIL 2013 Calculations for determining the most significant power losses are shown below. Other losses totaling less than 2% are not discussed. Power loss (PLOSS) is the sum of two basic types of losses in the converter, switching and conduction. Conduction losses usually dominate at higher output loads, where as switching losses remain relatively fixed and dominate at lower output loads. The first step in determining the losses is to calculate the duty cycle (D). VOUT + VD D= VIN + VD - VSW (27) VSW is the voltage drop across the internal NFET when it is on, and is equal to: VSW = IOUT x RDSON (28) VD is the forward voltage drop across the Schottky diode. It can be obtained from the Electrical Characteristics section. If the voltage drop across the inductor (VDCR) is accounted for, the equation becomes: VO + VD + VDCR D= VIN + VD - VSW (29) This usually gives only a minor duty cycle change, and has been omitted in the examples for simplicity. The conduction losses in the free-wheeling Schottky diode are calculated as follows: PDIODE = VD x IOUT(1-D) (30) Often this is the single most significant power loss in the circuit. Care should be taken to choose a Schottky diode that has a low forward voltage drop. Another significant external power loss is the conduction loss in the output inductor. The equation can be simplified to: PIND = IOUT2 x RDCR (31) The LM2734Z conduction loss is mainly associated with the internal NFET: PCOND = IOUT2 x RDSON x D (32) Switching losses are also associated with the internal NFET. They occur during the switch on and off transition periods, where voltages and currents overlap resulting in power loss. The simplest means to determine this loss is to empirically measuring the rise and fall times (10% to 90%) of the switch at the switch node: PSWF = 1/2(VIN x IOUT x freq x TFALL) PSWR = 1/2(VIN x IOUT x freq x TRISE) PSW = PSWF + PSWR (33) (34) (35) Table 1. Typical Rise and Fall Times vs Input Voltage VIN TRISE TFALL 5V 8ns 4ns 10V 9ns 6ns 15V 10ns 7ns Another loss is the power required for operation of the internal circuitry: PQ = IQ x VIN (36) IQ is the quiescent operating current, and is typically around 1.5mA. The other operating power that needs to be calculated is that required to drive the internal NFET: PBOOST = IBOOST x VBOOST (37) VBOOST is normally between 3VDC and 5VDC. The IBOOST rms current is approximately 4.25mA. Total power losses are: 6PCOND + PSW + PDIODE + PIND + PQ + PBOOST = PLOSS (38) Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM2734Z 13 LM2734Z SNVS334E - JANUARY 2005 - REVISED APRIL 2013 www.ti.com Design Example 1: Operating Conditions VIN 5.0V POUT 2.5W VOUT 2.5V PDIODE 151mW IOUT 1.0A PIND 75mW VD 0.35V PSWF 53mW Freq 3MHz PSWR 53mW IQ 1.5mA PCOND 187mW TRISE 8ns PQ 7.5mW TFALL 8ns PBOOST 21mW RDSON 330m PLOSS 548mW INDDCR 75m D 0.568 = 82% Calculating the LM2734Z Junction Temperature Thermal Definitions: TJ = Chip junction temperature TA = Ambient temperature RJC = Thermal resistance from chip junction to device case RJA = Thermal resistance from chip junction to ambient air Figure 13. Cross-Sectional View of Integrated Circuit Mounted on a Printed Circuit Board Heat in the LM2734Z due to internal power dissipation is removed through conduction and/or convection. Conduction: Heat transfer occurs through cross sectional areas of material. Depending on the material, the transfer of heat can be considered to have poor to good thermal conductivity properties (insulator vs conductor). Heat Transfer goes as: siliconpackagelead framePCB. Convection: Heat transfer is by means of airflow. This could be from a fan or natural convection. Natural convection occurs when air currents rise from the hot device to cooler air. Thermal impedance is defined as: RT = 14 'T Power (39) Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM2734Z LM2734Z www.ti.com SNVS334E - JANUARY 2005 - REVISED APRIL 2013 Thermal impedance from the silicon junction to the ambient air is defined as: TJ - TA RTJA = Power (40) This impedance can vary depending on the thermal properties of the PCB. This includes PCB size, weight of copper used to route traces and ground plane, and number of layers within the PCB. The type and number of thermal vias can also make a large difference in the thermal impedance. Thermal vias are necessary in most applications. They conduct heat from the surface of the PCB to the ground plane. Four to six thermal vias should be placed under the exposed pad to the ground plane if the WSON package is used. If the Thin SOT-6 package is used, place two to four thermal vias close to the ground pin of the device. The datasheet specifies two different RJA numbers for the Thin SOT-6 package. The two numbers show the difference in thermal impedance for a four-layer board with 2oz. copper traces, vs. a four-layer board with 1oz. copper. RJA equals 120C/W for 2oz. copper traces and GND plane, and 235C/W for 1oz. copper traces and GND plane. Method 1: To accurately measure the silicon temperature for a given application, two methods can be used. The first method requires the user to know the thermal impedance of the silicon junction to case. (RJC) is approximately 80C/W for the Thin SOT-6 package. Knowing the internal dissipation from the efficiency calculation given previously, and the case temperature, which can be empirically measured on the bench we have: TJ - TC RTJA = Power (41) Therefore: TJ = (RJC x PLOSS) + TC (42) Design Example 2: Operating Conditions VIN 5.0V POUT 2.5W VOUT 2.5V PDIODE 151mW IOUT 1.0A PIND 75mW VD 0.35V PSWF 53mW Freq 3MHz PSWR 53mW IQ 1.5mA PCOND 187mW TRISE 8ns PQ 7.5mW TFALL 8ns PBOOST 21mW RDSON 330m PLOSS 548mW INDDCR 75m D 0.568 6PCOND + PSWF + PSWR + PQ + PBOOST = PINTERNAL PINTERNAL = 322 mW TJ = (RTJC x Power) + TC = 80oC/W x 322 mW + TC (43) The second method can give a very accurate silicon junction temperature. The first step is to determine RJA of the application. The LM2734Z has over-temperature protection circuitry. When the silicon temperature reaches 165C, the device stops switching. The protection circuitry has a hysteresis of 15C. Once the silicon temperature has decreased to approximately 150C, the device will start to switch again. Knowing this, the RJA for any PCB can be characterized during the early stages of the design by raising the ambient temperature in the given application until the circuit enters thermal shutdown. If the SW-pin is monitored, it will be obvious when the internal NFET stops switching indicating a junction temperature of 165C. Knowing the internal power dissipation from the above methods, the junction temperature and the ambient temperature, RJA can be determined. Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM2734Z 15 LM2734Z SNVS334E - JANUARY 2005 - REVISED APRIL 2013 www.ti.com 165oC - TA RTJA = PINTERNAL (44) Once this is determined, the maximum ambient temperature allowed for a desired junction temperature can be found. Design Example 3: Operating Conditions Package SOT-6 VIN 12.0V POUT 2.475W VOUT 3.30V PDIODE 523mW IOUT 750mA PIND 56.25mW VD 0.35V PSWF 108mW Freq 3MHz PSWR 108mW IQ 1.5mA PCOND 68.2mW IBOOST 4mA PQ 18mW VBOOST 5V PBOOST 20mW TRISE 8ns PLOSS 902mW TFALL 8ns RDSON 400m INDDCR 75m D 30.3% 6PCOND + PSWF + PSWR + PQ + PBOOST = PINTERNAL PINTERNAL = 322 mW (45) Using a standard Texas Instruments Thin SOT-6 demonstration board to determine the RJA of the board. The four layer PCB is constructed using FR4 with 1/2oz copper traces. The copper ground plane is on the bottom layer. The ground plane is accessed by two vias. The board measures 2.5cm x 3cm. It was placed in an oven with no forced airflow. The ambient temperature was raised to 94C, and at that temperature, the device went into thermal shutdown. RTJA = 165oC - 94oC 322 mW = 220oC/W (46) If the junction temperature was to be kept below 125C, then the ambient temperature cannot go above 54.2C. TJ - (RJA x PLOSS) = TA (47) The method described above to find the junction temperature in the Thin SOT-6 package can also be used to calculate the junction temperature in the WSON package. The 6 pin WSON package has a RJC = 20C/W, and RJA can vary depending on the application. RJA can be calculated in the same manner as described in method #2 (see example 3). 16 Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM2734Z LM2734Z www.ti.com SNVS334E - JANUARY 2005 - REVISED APRIL 2013 WSON PACKAGE The LM2734Z is packaged in a Thin SOT-6 package and the 6-pin WSON. The WSON package has the same footprint as the Thin SOT-6, but is thermally superior due to the exposed ground paddle on the bottom of the package. Figure 14. No Pullback WSON Configuration RJA of the WSON package is normally two to three times better than that of the Thin SOT-6 package for a similar PCB configuration (area, copper weight, thermal vias). FB 1 GND BOOST 2 3 6 EN 5 VIN 4 SW Figure 15. Dog Bone For certain high power applications, the PCB land may be modified to a "dog bone" shape (see Figure 15). By increasing the size of ground plane, and adding thermal vias, the RJA for the application can be reduced. Design Example 4: Operating Conditions Package WSON-6 VIN 12.0V POUT 2.475W VOUT 3.3V PDIODE 523mW IOUT 750mA PIND 56.25mW VD 0.35V PSWF 108mW Freq 3MHz PSWR 108mW IQ 1.5mA PCOND 68.2mW IBOOST 4mA PQ 18mW VBOOST 5V PBOOST 20mW TRISE 8ns PLOSS 902mW TFALL 8ns RDSON 400m INDDCR 75m D 30.3% Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM2734Z 17 LM2734Z SNVS334E - JANUARY 2005 - REVISED APRIL 2013 www.ti.com 6PCOND + PSWF + PSWR + PQ + PBOOST = PINTERNAL PINTERNAL = 322 mW (48) This example follows example 2, but uses the WSON package. Using a standard Texas Instruments WSON-6 demonstration board, use Method 2 to determine RJA of the board. The four layer PCB is constructed using FR4 with 1/2oz copper traces. The copper ground plane is on the bottom layer. The ground plane is accessed by four vias. The board measures 2.5cm x 3cm. It was placed in an oven with no forced airflow. The ambient temperature was raised to 113C, and at that temperature, the device went into thermal shutdown. RTJAa = 165oC - 113oC 322 mW = 161oC/W (49) If the junction temperature is to be kept below 125C, then the ambient temperature cannot go above 73.2C. TJ - (RJA x PLOSS) = TA (50) Package Selection To determine which package you should use for your specific application, variables need to be known before you can determine the appropriate package to use. 1. Maximum ambient system temperature 2. Internal LM2734Z power losses 3. Maximum junction temperature desired 4. RJA of the specific application, or RJC (WSON or Thin SOT-6) The junction temperature must be less than 125C for the worst-case scenario. 18 Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM2734Z LM2734Z www.ti.com SNVS334E - JANUARY 2005 - REVISED APRIL 2013 LM2734Z Design Examples D2 VIN BOOST VIN C3 C1 L1 R3 VOUT SW LM2734 ON D1 EN C2 R1 OFF FB GND R2 Figure 16. VBOOST Derived from VIN Operating Conditions: 5V to 1.5V/1A Table 2. Bill of Materials for Figure 16 Part ID Part Value Part Number Manufacturer U1 1A Buck Regulator LM2734ZX Texas Instruments C1, Input Cap 10F, 6.3V, X5R C3216X5ROJ106M TDK C2, Output Cap 10F, 6.3V, X5R C3216X5ROJ106M TDK C3, Boost Cap 0.01uF, 16V, X7R C1005X7R1C103K TDK D1, Catch Diode 0.3VF Schottky 1A, 10VR MBRM110L ON Semi D2, Boost Diode 1VF @ 50mA Diode 1N4148W Diodes, Inc. L1 2.2H, 1.8A ME3220-222MX Coilcraft R1 8.87k, 1% CRCW06038871F Vishay R2 10.2k, 1% CRCW06031022F Vishay R3 100k, 1% CRCW06031003F Vishay Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM2734Z 19 LM2734Z SNVS334E - JANUARY 2005 - REVISED APRIL 2013 www.ti.com D2 VIN BOOST VIN C3 C1 L1 R3 VOUT SW LM2734 ON D1 C2 EN OFF R1 FB GND R2 Figure 17. VBOOST Derived from VOUT 12V to 3.3V/1A Table 3. Bill of Materials for Figure 17 Part ID Part Value Part Number Manufacturer U1 1A Buck Regulator LM2734ZX Texas Instruments C1, Input Cap 10F, 25V, X7R C3225X7R1E106M TDK C2, Output Cap 22F, 6.3V, X5R C3216X5ROJ226M TDK C3, Boost Cap 0.01F, 16V, X7R C1005X7R1C103K TDK D1, Catch Diode 0.34VF Schottky 1A, 30VR SS1P3L Vishay D2, Boost Diode 0.6VF @ 30mA Diode BAT17 Vishay L1 3.3H, 1.3A ME3220-332MX Coilcraft R1 31.6k, 1% CRCW06033162F Vishay R2 10.0 k, 1% CRCW06031002F Vishay R3 100k, 1% CRCW06031003F Vishay 20 Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM2734Z LM2734Z www.ti.com SNVS334E - JANUARY 2005 - REVISED APRIL 2013 C4 D3 R4 D2 BOOST VIN VIN C3 C1 R3 L1 VOUT SW LM2734 ON D1 C2 EN OFF R1 FB GND R2 Figure 18. VBOOST Derived from VSHUNT 18V to 1.5V/1A Table 4. Bill of Materials for Figure 18 Part ID Part Value Part Number Manufacturer U1 1A Buck Regulator LM2734ZX Texas Instruments C1, Input Cap 10F, 25V, X7R C3225X7R1E106M TDK C2, Output Cap 22F, 6.3V, X5R C3216X5ROJ226M TDK C3, Boost Cap 0.01F, 16V, X7R C1005X7R1C103K TDK C4, Shunt Cap 0.1F, 6.3V, X5R C1005X5R0J104K TDK D1, Catch Diode 0.4VF Schottky 1A, 30VR SS1P3L Vishay D2, Boost Diode 1VF @ 50mA Diode 1N4148W Diodes, Inc. D3, Zener Diode 5.1V 250Mw SOT BZX84C5V1 Vishay L1 3.3H, 1.3A ME3220-332MX Coilcraft R1 8.87k, 1% CRCW06038871F Vishay R2 10.2k, 1% CRCW06031022F Vishay R3 100k, 1% CRCW06031003F Vishay R4 4.12k, 1% CRCW06034121F Vishay Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM2734Z 21 LM2734Z SNVS334E - JANUARY 2005 - REVISED APRIL 2013 www.ti.com D2 D3 BOOST VIN VIN C1 C3 R3 L1 VOUT SW LM2734 ON D1 EN C2 R1 OFF FB GND R2 Figure 19. VBOOST Derived from Series Zener Diode (VIN) 15V to 1.5V/1A Table 5. Bill of Materials for Figure 19 Part ID Part Value Part Number Manufacturer U1 1A Buck Regulator LM2734ZX Texas Instruments C1, Input Cap 10F, 25V, X7R C3225X7R1E106M TDK C2, Output Cap 22F, 6.3V, X5R C3216X5ROJ226M TDK C3, Boost Cap 0.01F, 16V, X7R C1005X7R1C103K TDK D1, Catch Diode 0.4VF Schottky 1A, 30VR SS1P3L Vishay D2, Boost Diode 1VF @ 50mA Diode 1N4148W Diodes, Inc. D3, Zener Diode 11V 350Mw SOT BZX84C11T Diodes, Inc. L1 3.3H, 1.3A ME3220-332MX Coilcraft R1 8.87k, 1% CRCW06038871F Vishay R2 10.2k, 1% CRCW06031022F Vishay R3 100k, 1% CRCW06031003F Vishay 22 Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM2734Z LM2734Z www.ti.com SNVS334E - JANUARY 2005 - REVISED APRIL 2013 D3 D2 VIN BOOST VIN C3 C1 R3 L1 VOUT SW LM2734 ON D1 EN C2 R1 OFF FB GND R2 Figure 20. VBOOST Derived from Series Zener Diode (VOUT) 15V to 9V/1A Table 6. Bill of Materials for Figure 20 Part ID Part Value Part Number Manufacturer U1 1A Buck Regulator LM2734ZX Texas Instruments C1, Input Cap 10F, 25V, X7R C3225X7R1E106M TDK C2, Output Cap 22F, 16V, X5R C3216X5R1C226M TDK C3, Boost Cap 0.01F, 16V, X7R C1005X7R1C103K TDK D1, Catch Diode 0.4VF Schottky 1A, 30VR SS1P3L Vishay D2, Boost Diode 1VF @ 50mA Diode 1N4148W Diodes, Inc. D3, Zener Diode 4.3V 350mw SOT BZX84C4V3 Diodes, Inc. L1 2.2H, 1.8A ME3220-222MX Coilcraft R1 102k, 1% CRCW06031023F Vishay R2 10.2k, 1% CRCW06031022F Vishay R3 100k, 1% CRCW06031003F Vishay Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM2734Z 23 LM2734Z SNVS334E - JANUARY 2005 - REVISED APRIL 2013 www.ti.com REVISION HISTORY Changes from Revision D (April 2013) to Revision E * 24 Page Changed layout of National Data Sheet to TI format .......................................................................................................... 23 Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM2734Z PACKAGE OPTION ADDENDUM www.ti.com 7-Oct-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish (2) MSL Peak Temp Op Temp (C) Device Marking (3) (4/5) LM2734ZMK/NOPB ACTIVE SOT DDC 6 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 SFTB LM2734ZMKX/NOPB ACTIVE SOT DDC 6 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 SFTB LM2734ZQMK/NOPB ACTIVE SOT DDC 6 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 SVBB LM2734ZQMKE/NOPB ACTIVE SOT DDC 6 250 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 SVBB LM2734ZQMKX/NOPB ACTIVE SOT DDC 6 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 SVBB LM2734ZQSD/NOPB ACTIVE WSON NGG 6 1000 Green (RoHS & no Sb/Br) CU SN Level-3-260C-168 HR -40 to 125 L238B LM2734ZQSDE/NOPB ACTIVE WSON NGG 6 250 Green (RoHS & no Sb/Br) CU SN Level-3-260C-168 HR -40 to 125 L238B LM2734ZQSDX/NOPB ACTIVE WSON NGG 6 4500 Green (RoHS & no Sb/Br) CU SN Level-3-260C-168 HR -40 to 125 L238B LM2734ZSD/NOPB ACTIVE WSON NGG 6 1000 Green (RoHS & no Sb/Br) CU SN Level-3-260C-168 HR -40 to 125 L163B LM2734ZSDX/NOPB ACTIVE WSON NGG 6 4500 Green (RoHS & no Sb/Br) CU SN Level-3-260C-168 HR -40 to 125 L163B (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 7-Oct-2013 (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF LM2734Z, LM2734Z-Q1 : * Catalog: LM2734Z * Automotive: LM2734Z-Q1 NOTE: Qualified Version Definitions: * Catalog - TI's standard catalog product * Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 23-Oct-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant LM2734ZMK/NOPB SOT DDC 6 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM2734ZMKX/NOPB SOT DDC 6 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM2734ZQMK/NOPB SOT DDC 6 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM2734ZQMKE/NOPB SOT DDC 6 250 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM2734ZQMKX/NOPB SOT DDC 6 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM2734ZQSD/NOPB WSON NGG 6 1000 178.0 12.4 3.3 3.3 1.0 8.0 12.0 Q1 LM2734ZQSDE/NOPB WSON NGG 6 250 178.0 12.4 3.3 3.3 1.0 8.0 12.0 Q1 LM2734ZQSDX/NOPB WSON NGG 6 4500 330.0 12.4 3.3 3.3 1.0 8.0 12.0 Q1 LM2734ZSD/NOPB WSON NGG 6 1000 178.0 12.4 3.3 3.3 1.0 8.0 12.0 Q1 LM2734ZSDX/NOPB WSON NGG 6 4500 330.0 12.4 3.3 3.3 1.0 8.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 23-Oct-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LM2734ZMK/NOPB SOT DDC 6 1000 210.0 185.0 35.0 LM2734ZMKX/NOPB SOT DDC 6 3000 210.0 185.0 35.0 LM2734ZQMK/NOPB SOT DDC 6 1000 210.0 185.0 35.0 LM2734ZQMKE/NOPB SOT DDC 6 250 210.0 185.0 35.0 LM2734ZQMKX/NOPB SOT DDC 6 3000 210.0 185.0 35.0 LM2734ZQSD/NOPB WSON NGG 6 1000 213.0 191.0 55.0 LM2734ZQSDE/NOPB WSON NGG 6 250 213.0 191.0 55.0 LM2734ZQSDX/NOPB WSON NGG 6 4500 367.0 367.0 35.0 LM2734ZSD/NOPB WSON NGG 6 1000 213.0 191.0 55.0 LM2734ZSDX/NOPB WSON NGG 6 4500 367.0 367.0 35.0 Pack Materials-Page 2 MECHANICAL DATA NGG0006A SDE06A (Rev A) www.ti.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2013, Texas Instruments Incorporated