UMPSERIESCONFIGURABLE - Emerson

Rev. 01.01.2012

µMP Series

1 of 6

313

process

yellow

3405

1797

1375

116

2607

652

242

2985

375

240

Embedded Power for

Business-Critical Continuity

Electrical Specifications

Input

Input ra nge: 85 - 264 Vac, 120 - 350 Vdc (limited to 250 Vac/300 Vdc in medical apps)

Frequency: 47 - 440 Hz

Inrush current: 40 A peak max. (soft start)

Efficiency: Up to 91% @ full case load

Power Factor: 0.99 typ. meets EN61000-3-2 (n/a @ 440 Hz)

Turn-on time: AC on 2 sec for uMP1 and 1.5 sec for uMP4, inhibit/enable 250 ms typical

EMI filter: CISPR 22/EN55022 Level “B”

Leakage current: 300 µA max. @ 240 Vac for uMP1 and 500 µA max for uMP4; 47 - 63 Hz

Radiated EMI: CISPR 22/EN55022 Level “B”

Holdover storage: 16.7 ms minimum (independent of input Vac, 0 °C to 50 °C))

AC OK: Signal goes low indicating loss of AC input.

Hold up = Full cycle ride thru (50 Hz)

Harmonic distortion: Meets EN61000-3-2

Isolation: Meets EN60950 and EN60601

Global Inhibit/Enable: TTL, Logic “1” and Logic “0”; fan off when unit is inhibited

Input fuse (internal): uMP1: 16 A/250 V TLAG, uMP4: 10 A / 250 V. (both lines fused)

Warranty: 2 years

µMP Series

Up to 1200 Watts

Special Features

• Full Medical EN60601 approval

• PMBus

• Highefficiency

• Currentlimitmodification

(foldback or constant current)

• Highpowerdensity.

uMP4: 10.8 W/cu-in

uMP1: 15.1 W/cu-in

• Intelligentfan

(speed control/fault status)

• DownloadableGUIfromwebsite

• uPcontrolledPFCinputwithactive

inrush protection

• Optionalconformalcoating

• Industrialtemprange(-40ºC to 70 ºC)

• Nopreloadrequired

• Industrialshock/vibration(>50G’s)

• Lowcost

• IECorterminalblockinput

• Lowprofile1Usize

Total Power: Up to 1200 Watts

Input Voltage: 85 - 264 Vac

120-300 Vdc

# of Outputs: Up to 12

Safety

• UL UL60950/UL60601-1

• CSA CSA22.2 No. 234 Level 5

• VDE EN60950/EN60601-1

• BABT Compliance to

EN60950/EN60601 BS7002

• CB Certificate and report

• CE  MarktoLVD

• CCC Approved

• BSMI Approved

MicroMP 1U Multi Output

Operating temperature: -40°to70°Cambient.Derateeachoutput2.5%perdegreefrom50°Cto70°C.

( -20 °C start up). Meets full spec after 1/2 load. 10 min warm-up

Storage temperature: -40 °C to 85 °C

Electromagnetic susceptibility: DesignedtomeetEN61000-4;-3,-5,-6,-11Level3,Level4for-2,-4

Humidity: Operating; non-condensing 10% to 95% RH

Vibration: MIL-STD-810E

MTBF demonstrated: >350,000hoursatfullload,oneuMP4case+twomodules,TelcordiaSR-332

calculated MTBF

Altitude: Up to 10k feet; derate linear to 50% from 10k-30k feet

Environmental Specifications

µMP4C shown

Rev. 01.01.2012

µMP Series

2 of 6

Embedded Power for

Business-Critical Continuity

313

process

yellow

3405

1797

1375

116

2607

652

242

2985

375

240

Output

Factory set point accuracy: ± 1%

Margining: ± 3 - 7% nominal analog (single output module only)

Overall regulation: 0.4% or 30 mV which ever is greater.

Ripple: RMS: 0.1% or 10 mV, whichever is greater

Pk-Pk: 1.0% or 50 mV, whichever is greater. Bandwidth limited to 20 MHz

Dynamicresponse: < ± 5% or 250 mV, with 50% step load

Recovery time: To within 1% in < 300 µsec

Reverse voltage protection: 100% of rated output current

Thermal protection:

(OTP)

All outputs disabled when internal temp exceeds safe operating range.

Remote sense: Up to 0.5 V total drop (not available on triple output module)

Single wire parallel: Current share to within 5% of total rated current

DCOK: ± 5% of nominal.

Minimum load: Not required

Housekeeping standby: 5 Vdc @ 1.0 A max. present whenever AC input is applied

Module inhibit: Logic-outputonwithloworopen.Differentlogicoptionsavailable

Output/Output isolation: >1Megohm,500V

Vout Full load

(A)

OVP trip max

(V)

OCP trip typ (I-

out%)

SCP trip max (I-

out%)

Overshoot (max

mV)

Peak Deviation

(max mV)

3V3 Module

0.9 40 TBD 130% 160% 150 ± 250

3.3 40 5.96 V 130% 160% 250 ± 250

3.6 40 6.32 V 130% 160% 250 ± 250

5 V Module

3.2 36 6.8 V 130% 160% 250 ± 250

5 36 8.8 V 130% 160% 250 ± 250

6 30 9.2 V 130% 160% 300 ± 300

12 V Module

6 25 12 V 130% 160% 300 ± 300

12 20 18 V 130% 160% 600 ± 600

15 16 20 V 130% 160% 750 ± 750

24 V Module

12 13 18 V 130% 160% 600 ± 600

24 10 31 V 130% 160% 1200 ± 1200

30 8 38 V 130% 160% 1500 ± 1500

48 V Module

28 7 TBD 130% 200% 1400 ± 1400

48 5 TBD 130% 160% 2400 ± 2400

60 4 TBD 130% 200% 3000 ± 3000

Case Line-Up

Case Max Output Dimensions Connections Max Current Amps

µMP4 - 4 Slot 400 W - 600 W 256.9±0.8 x 88.9±0.5 x 40.0±0.7

(10.11” x 3.5” x 1.57”) IEC/Terminal Block 9.91

µMP1 - 6 Slot 1000 W - 1200 W 256.9±0.8 x 127±0.5 x 40.0±0.5

(10.11” x 5” x 1.57”) IEC/Terminal Block 13.87

Output Module Line-Up

Output Range

(Vdc)

Max Current

(Amps)

Max Power

(Watts)

Module Codes

Standard Outputs

0.9 - 3.6 40 144 A,B,C,D-2,2.2,3,3.3

3.2 - 6.0 36 180 E, F, G, H - 5, 5, 2, 5.5, 6

6.0 - 15.0 25 240 I, J, K, L, M, N - 8, 10, 11, 12, 14, 15

12.0 - 30.0 13 240 O, P, Q, R, S - 18, 20, 24, 28, 30

28.0 - 54.0 7 240 T, U, V, W, X, Y - 28, 30, 33, 36, 42, 48, 54, 60

5.0 - 28.0

DualOutputModule.Eachoutputisratedto96W(192

Watts total). Wide range is adjustable.

Rev. 01.01.2012

µMP Series

3 of 6

Embedded Power for

Business-Critical Continuity

313

process

yellow

3405

1797

1375

116

2607

652

242

2985

375

240

Ordering Info

µMPXY - S2E - DER - DLL - 00 - A - ###

Case Option Codes

First digit

0 - F = Parallel Code

Second digit

0 = No Options

1 = Reverse Air

3 = Global Enable

5=Opt1+Opt3

Software Code

Case Option Codes

Factory assigned

for modified

standards

Module Codes

S2 = 200 W Single O/P (1 slot)

D=96W/96WDualO/PCommon

Ground (1 slot)

I=96W/96WDualO/PIsolated

Ground (1 slot)

Voltage Codes:

See Voltage Code Table

Module/Voltage/Option Codes

Case Size

Single - Phase Input where X =

4 = 1.57” x 3.5” x 10”; 400 W - 600 W, 4 Slots

1 = 1.57” x 5” x 10”; 1000 W - 1200 W, 6 Slots

Input Type where Y =

T = Terminal Block

C = IEC Connector, C14

B = IEC Connector, C16

Case Size

Factory assigned

for modified

standards

Hardware Code

Standard Output Ratings

Module Output

Voltage Code

Single Output ONE SLOT

240 Watts Max

DualOutputONESLOT

192 Watts Max

ModuleIdentication S2 D=DualCommonGround

I=DualIsolatedGround

Voltage Codes

Output Module Line-Up

Code Volts Output Current

Output Current

V1 V2

A2.0 V 40.0 N/A

B2.2 V 40.0 N/A

C3.0 V 40.0 N/A

D3.3 V 40.0 4.0* 4.0*

E5.0 V 36.0 4.0 4.0

F5.2 V 34.0 4.0 4.0

G5.5 V 32.0 4.0 4.0

H6.0 V 30.0 4.0 4.0

I8.0 V 25.0 4.0 4.0

J10.0 V 24.0 4.0 4.0

K11.0 V 22.0 4.0 4.0

L12.0 V 20.0 4.0 4.0

M14.0 V 17.0 4.0 4.0

N15.0 V 16.0 4.0 4.0

O18.0 V 13.0 4.0 4.0

P20.0 V 12.0 4.0 4.0

Q24.0 V 10.0 4.0 4.0

R28.0 V 8.6 3.4 3.4

S30.0 V 8.0 N/A

T33.0 V 7 N/A

U36.0 V 6.7 N/A

V42.0 V 5.7 N/A

W48.0 V 5.0 N/A

X54.0 V 4.4 N/A

Y60.0 V 4.0 N/A

* For “I” codes only

DeratingCurves-µMP1

400

500

600

700

800

900

1000

1100

1200

010203040506070

Output Power

Temperature

Standard Fan(12 V/24 V/48 V)

85 VAC 100 VAC 110 VAC 200 VAC 264 VAC

400

500

600

700

800

900

1000

1100

1200

010203040506070

Output Power

Temperature

Reverse FAN(12 V/24 V/48V)

85 VAC 100 VAC 110 VAC 200 VAC 264 VAC

Parallel Codes

Code Slots in Parallel Code Slots in Parallel Code Slots in Parallel Code Slots in Parallel

1 1&2 6 1,2&3 B 1,2&3; 4&5 0no module in

parallel

2 2&3 7 1,2,3&4 C 1,2,3&4; 5&6

3 3&4 8 1,2,3,4&5 D1&2; 3&4; 5&6

4 4&5 9 1,2,3,4,5&6 E 1,2&3; 4,5&6

5 5&6 A 1&2; 3&4 F2&3; 4&5

Rev. 01.01.2012

µMP Series

4 of 6

Embedded Power for

Business-Critical Continuity

313

process

yellow

3405

1797

1375

116

2607

652

242

2985

375

240

Input

85-264 Vac 200-264 Vac

µMP1 = 6 available slots 1000 W max. 1200 W max.

4321

µMP4 (AC input on opposite side)

µMP1 (AC input on opposite side)

S2 Module

AC Input

Pin Function

1AC neutral

2AC line (hot)

3Chassis (earth) ground

PFC Input Connector (control & signals)

Pin Function

1Input AC OK - “emitter”

2Input AC OK - “collector”

3GlobalDCOK-“emitter”

4GlobalDCOK-“collector”

5 Spare

6Global inhibit/optional enable logic “1”

7Global inhibit/optional enable logic “0”

8Global inhibit/optional enable return

9+5VSBhousekeeping

10 +5VSBhousekeepingreturn

I2C Bus Output Connector

Pin Function

15 Vcc bus

2Serialdatasignal(SDA)

3Secondary return (COM)

4Serial clock signal (SCL)

5Address bit 2 (A2)

6No connection

7Address bit 1 (A1)

8No connection

9Address bit 0 (A0)

10 No connection

Mates with

Landwin 2050S1000 Housing

2053T011V Pin

JSTPHDR-10VSHousing

JSTSPHD-002T-P0.5(28-24)

JSTSPHD-001T-P0.5(26-22)

Connector Kit Part No.:

70-841-023

Figure 1. AC Input

Figure 2. Connector J1 & J2

Input

85-264 Vac 200-264 Vac

µMP4 =4 available slots 400 W max. 600 W max.

240 W

Pin Connectors

Dual Module

1.0±0.25

5.3±0.5

4.5±0.3

36.5±0.3

0.8 - 1.5

130.0±1.5

1.6±0.16

29.8±0.2

32.5±0.3

36.5±0.3

37.5±0.3

12.5 MAX

3.0 MAX

CAPS HEIGHT

V ADJ

V+

V-

IEC Connector

Terminal Block

LNPE

DC Output Control & Signals

(Single output)

Pin Function

1No connection

2No connection

3Current share

4Module inhibit return

5Module ISO inhibit

6 SCOM

7-RMT sense

8 Margin

9Remote margin / V prog.

10 +RMTsense

DC Output Control & Signals

(Dual output)

Pin Function

1-RMT sense V2

2+RMTsenseV2

3No connection

4Module inhibit rtn

5Module ISO inhibit

6 SCOM

7-RMT sense V1

8No connection

9No connection

10 +RMTsenseV1

122.0 ± 0.5

1.6 ± 0.15

12.5 MAX

2.5 MAX

0 ~ 0.1 mm

(2X)

130.0 ref

37.8 ± 0.3

V1 ADJ V2 ADJ

V1+

COM

V2+

COM

Rev. 01.01.2012

µMP Series

5 of 6

Embedded Power for

Business-Critical Continuity

313

process

yellow

3405

1797

1375

116

2607

652

242

2985

375

240

µMP Series

µMP4 (400/600 Watts Max)

Case Size: µMP4: 10.11” x 3.5” x 1.57” (256.9mm x 88.9mm x 40.0mm)

Weight: µMP4Case:1.96lbs•SingleO/P:0.22lb.•DualO/P:0.16lb.

•Blank:0.06lb.

Rev. 01.01.2012

µMP Series

6 of 6

Embedded Power for

Business-Critical Continuity

313

process

yellow

3405

1797

1375

116

2607

652

242

2985

375

240

Americas

5810 Van Allen Way

Carlsbad, CA 92008

USA

Telephone:+17609304600

Facsimile: +17609300698

Europe (UK)

Waterfront Business Park

MerryHill,Dudley

WestMidlands,DY51LX

United Kingdom

Telephone:+44(0)1384842211

Facsimile: +44(0)1384843355

Asia (HK)

14/F, Lu Plaza

2 Wing Yip Street

Kwun Tong, Kowloon

Hong Kong

Telephone:+85221763333

Facsimile: +85221763888

For global contact, visit:

www.Emerson.com/EmbeddedPower

techsupport.embeddedpower

@emerson.com

While every precaution has been taken to ensure

accuracy and completeness in this literature, Emerson

Network Power assumes no responsibility, and disclaims

all liability for damages resulting from use of this

information or for any errors or omissions.

Emerson Network Power and the Emerson

Network Power logo are trademarks and

service marks of Emerson Electric Co.

EmersonNetworkPower.com

Embedded Computing

Embedded Power

Monitoring

Outside Plant

Power Switching & Controls

Precision Cooling

Racks & Integrated Cabinets

Services

Surge Protection

Emerson Network Power.

The global leader in enabling

business-critical continuity.

AC Power

Connectivity

DCPower

Case Size: µMP1: 10.11” x 5” x 1.57” (256.9mm x 127mm x 40.0mm)

Weight: µMP1Case:2.78lbs•SingleO/P:0.22lb.

•DualO/P:0.16lb.•Blank:0.06lb.

µMP Series

µMP1 (1000/1200 Watts Max)