BFQ67-BLK - NXP SEMICONDUCTORS

5KP8.5A thru 5KP188A

www.vishay.com Vishay General Semiconductor

Revision: 24-Jun-14 1Document Number: 88308

For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

TRANSZORB® Transient Voltage Suppressors

FEATURES

• P600 glass passivated chip junction

• Available in uni-directional polarity only

• 5000 W peak pulse power capability with

a 10/1000 μs waveform, repetitive rate

(duty cycle): 0.01 %

• Excellent clamping capability

• Very fast response time

• Low incremental surge resistance

• Solder dip 275 °C max. 10 s, per JESD 22-B106

• AEC-Q101 qualified

• Material categorization: for definitions of compliance

please see www.vishay.com/doc?99912

TYPICAL APPLICATIONS

Use in sensitive electronics protection against voltage

transients induced by inductive load switching and lighting

on ICs, MOSFET, signal lines of sensor units for consumer,

computer, industrial, automotive, and telecommunication.

MECHANICAL DATA

Case: Molded epoxy body over passivated junction

Molding compound meets UL 94 V-0 flammability rating

Base P/N-E3 - RoHS compliant, commercial grade

Base P/NHE3 - RoHS compliant, AEC-Q101 qualified

Terminals: Matte tin plated leads, solderable per

J-STD-002 and JESD 22-B102

E3 suffix meets JESD 201 class 1A whisker test, HE3 suffix

meets JESD 201 class 2 whisker test

Polarity: Color band denotes cathode end

Notes

(1) Non-repetitive current pulse, per fig. 3 and derated above TA = 25 °C per fig. 2

(2) Measured 8.3 ms single half sine-wave or equivalent square wave, duty cycle = 4 pulses per minute maximum

PRIMARY CHARACTERISTICS

VWM 8.5 V to 188 V

VBR 9.4 V to 231 V

PPPM 5000 W

PD8.0 W

IFSM 500 A

TJ max. 175 °C

Polarity Uni-directional

Package P600

P600

MAXIMUM RATINGS (TA = 25 °C unless otherwise noted)

PARAMETER SYMBOL LIMIT UNIT

Peak pulse power dissipation with a 10/1000 μs waveform (1) P

PPM 5000 W

Peak pulse current with a 10/1000 μs waveform (1) I

PPM See next table A

Power dissipation on infinite heatsink at TL = 75 °C (fig. 5) PD8.0 W

Peak forward surge current 8.3 ms single half sine-wave (fig. 5) IFSM 600 A

Instantaneous forward voltage at 100 A (2) VF3.5 V

Operating junction and storage temperature range TJ, TSTG -55 to +175 °C

5KP8.5A thru 5KP188A

www.vishay.com Vishay General Semiconductor

Revision: 24-Jun-14 2Document Number: 88308

For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Notes

(1) Pulse test: tp  50 ms

(2) Surge current waveform per fig. 3 and derate per fig. 2

(3) All terms and symbols are consistent with ANSI/IEEE CA62.35

ELECTRICAL CHARACTERISTICS (JEDEC REGISTERED DATA) (TA = 25 °C unless otherwise noted)

DEVICE

TYPE

BREAKDOWN

VOLTAGE

VBR AT IT (1)

(V)

TEST

CURRENT

(mA)

STAND-OFF

VOLTAGE

VWM

(V)

MAXIMUM

REVERSE

LEAKAGE

AT VWM

ID (μA)

MAXIMUM

PEAK PULSE

CURRENT

IPPM (2)

(A)

MAXIMUM

CLAMPING

VOLTAGE AT

IPPM

VC (V)

MAXIMUM TEMP.

COEFFICIENT

OF VBR

(%/°C)

MIN. MAX.

5KP8.5A 9.44 10.4 5.0 8.5 50 347 14.4 0.078

5KP9.0A 10.0 11.1 5.0 9.0 20 325 15.4 0.081

5KP10A 11.1 12.3 5.0 10.0 15 294 17.0 0.084

5KP11A 12.2 13.5 5.0 11.0 10 275 18.2 0.086

5KP12A 13.3 14.7 5.0 12.0 5.0 251 19.9 0.088

5KP13A 14.4 15.9 5.0 13.0 2.0 233 21.5 0.090

5KP14A 15.6 17.2 5.0 14.0 2.0 216 23.2 0.092

5KP15A 16.7 18.5 5.0 15.0 2.0 205 24.4 0.094

5KP16A 17.8 19.7 5.0 16.0 2.0 192 26.0 0.096

5KP17A 18.9 20.9 5.0 17.0 2.0 181 27.6 0.097

5KP18A 20.0 22.1 5.0 18.0 2.0 171 29.2 0.098

5KP20A 22.2 24.5 5.0 20.0 2.0 154 32.4 0.099

5KP22A 24.4 26.9 5.0 22.0 2.0 141 35.5 0.100

5KP24A 26.7 29.5 5.0 24.0 2.0 129 38.9 0.101

5KP26A 28.9 31.9 5.0 26.0 2.0 119 42.1 0.101

5KP28A 31.1 34.4 5.0 28.0 2.0 110 45.4 0.102

5KP30A 33.3 36.8 5.0 30.0 2.0 103 48.4 0.103

5KP33A 36.7 40.6 5.0 33.0 2.0 93.8 53.3 0.104

5KP36A 40.0 44.2 5.0 36.0 2.0 86.1 58.1 0.104

5KP40A 44.4 49.1 5.0 40.0 2.0 77.5 64.5 0.105

5KP43A 47.8 52.8 5.0 43.0 2.0 72.0 69.4 0.105

5KP45A 50.0 55.3 5.0 45.0 2.0 68.8 72.7 0.106

5KP48A 53.3 58.9 5.0 48.0 2.0 64.6 77.4 0.106

5KP51A 56.7 62.7 5.0 51.0 2.0 60.7 82.4 0.107

5KP54A 60.0 66.3 5.0 54.0 2.0 57.4 87.1 0.107

5KP58A 64.4 71.2 5.0 58.0 2.0 53.4 94 0.107

5KP60A 66.7 73.7 5.0 60.0 2.0 51.7 97.0 0.108

5KP64A 71.1 78.6 5.0 64.0 2.0 48.5 103 0.108

5KP70A 77.8 86.0 5.0 70.0 2.0 44.2 113 0.108

5KP75A 83.3 92.1 5.0 75.0 2.0 41.3 121 0.108

5KP78A 86.7 95.8 5.0 78.0 2.0 39.7 126 0.108

5KP85A 94.4 104 5.0 85.0 2.0 36.5 137 0.110

5KP90A 100 111 5.0 90.0 2.0 34.2 146 0.110

5KP100A 111 123 5.0 100 2.0 30.9 162 0.110

5KP110A 122 135 5.0 110 2.0 28.2 177 0.112

5KP120A 133 147 5.0 120 2.0 25.9 193 0.112

5KP130A 144 159 5.0 130 2.0 23.9 209 0.112

5KP150A 167 185 5.0 150 2.0 20.6 243 0.112

5KP160A 178 197 5.0 160 2.0 19.3 259 0.112

5KP170A 189 209 5.0 170 2.0 18.2 275 0.112

5KP188A 209 231 5.0 188 2.0 15.2 328 0.112

5KP8.5A thru 5KP188A

www.vishay.com Vishay General Semiconductor

Revision: 24-Jun-14 3Document Number: 88308

For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Note

(1) AEC-Q101 qualified

RATINGS AND CHARACTERISTICS CURVES (TA = 25 °C unless otherwise noted)

Fig. 1 - Peak Pulse Power Rating Curve

Fig. 2 - Pulse Power or Current vs. Initial Junction Temperature

Fig. 3 - Pulse Waveform

Fig. 4 - Typical Junction Capacitance

ORDERING INFORMATION (Example)

PREFERRED P/N UNIT WEIGHT (g) PREFERRED PACKAGE CODE BASE QUANTITY DELIVERY MODE

5KP8.5A-E3/54 2.776 54 800 13" diameter paper tape and reel

5KP8.5AHE3/54 (1) 2.776 54 800 13" diameter paper tape and reel

0.1 µs 1.0 µs 10 µs 100 µs 1 ms 10 ms

0.1

1.0

100

Non-Repetitive pulse

waveform shown in Fig. 3

= 25 °C

PPM

- Peak Pulse Power (kW)

- Pulse Width

100

0 25 50 75 100 125 150 175 200

Peak Pulse Power (P

) or Current (I

)

Derating in Percentage, %

TJ - Initial Temperature (°C)

100

150

= 10 µs

Peak Value

IPPM

Half Value -

IPPM

10/1000 µs Waveform

as defined by R.E.A.

01.0 2.0 3.0 4.0

t - Time (ms)

PPM

- Peak Pulse Current, % I

RSM

= 25 °C

Pulse Width (t

)

is defined as the Point

where the Peak Current

decays to 50 % of I

PPM

110 100 200

100

1000

10 000

100 000

- Junction Capacitance (pF)

VWM - Reverse Stand-Off Voltage (V)

Measured at

Zero Bias

Measured at Stand-Off

Voltage V

= 25 °C

f = 1.0 MHz

sig

= 50 mV

p-p

5KP8.5A thru 5KP188A

www.vishay.com Vishay General Semiconductor

Revision: 24-Jun-14 4Document Number: 88308

For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Fig. 5 - Power Derating Curve Fig. 6 - Maximum Non-Repetitive Forward Surge Current

PACKAGE OUTLINE DIMENSIONS in inches (millimeters)

APPLICATION NOTES

The 5KP series of high power transient voltage suppressors

were designed to be used on the output of switching power

supplies. These devices may be used to replace crowbar

circuits. Both the 5 % and 10 % voltage tolerances are

referenced to the power supply output voltage level.

They are able to withstand high levels of peak current while

allowing a circuit breaker to trip or a fuse blow before

shorting. This will enable the user to reset the breaker or

replace the fuse and continue operation. For this type

operation, it is recommended that a sufficient mounting

surface be used for dissipating the heat generated by the

Transient Voltage Suppressor during the transient or

over-voltage condition.

L = 0.375" (9.5 mm)

Lead Lengths

- Power Dissipation (W)

TL - Lead Temperature (°C)

60 Hz

Resistive or

Inductive Load

0 25 50 75 100 125 150 175 200

110 100

200

300

400

500

450

350

250

8.3 ms Single Half Sine-Wave

Number of Cycles at 60 Hz

FSM

- Peak Forward Surge Current (A)

0.052 (1.32)

0.048 (1.22)

0.360 (9.1)

0.340 (8.6)

DIA.

1.0 (25.4)

MIN.

0.360 (9.1)

0.340 (8.6)

1.0 (25.4)

MIN.

P600

Legal Disclaimer Notice

www.vishay.com Vishay

Revision: 08-Feb-17 1Document Number: 91000

Disclaimer



ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE

RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.

Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,

“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other

disclosure relating to any product.

Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or

the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all

liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,

consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular

purpose, non-infringement and merchantability.

Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of

typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding

statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a

particular product with the properties described in the product specification is suitable for use in a particular application.

Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over

time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s

technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,

including but not limited to the warranty expressed therein.

Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining

applications or for any other application in which the failure of the Vishay product could result in personal injury or death.

Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk.

Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for

such applications.

No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document

or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.