LP3962,LP3965
LP3962/LP3965 1.5A Fast Ultra Low Dropout Linear Regulators
Literature Number: SNVS066G
LP3962/LP3965
1.5A Fast Ultra Low Dropout Linear Regulators
General Description
The LP3962/LP3965 series of fast ultra low-dropout linear
regulators operate from a +2.5V to +7.0V input supply. Wide
range of preset output voltage options are available. These
ultra low dropout linear regulators respond very fast to step
changes in load which makes them suitable for low voltage
microprocessor applications. The LP3962/LP3965 are de-
veloped on a CMOS process which allows low quiescent
current operation independent of output load current. This
CMOS process also allows the LP3962/LP3965 to operate
under extremely low dropout conditions.
Dropout Voltage: Ultra low dropout voltage; typically 38mV
at 150mA load current and 380mV at 1.5A load current.
Ground Pin Current: Typically 5mA at 1.5A load current.
Shutdown Mode: Typically 15µA quiescent current when
the shutdown pin is pulled low.
Error Flag: Error flag goes low when the output voltage
drops 10% below nominal value (for LP3962).
SENSE: Sense pin improves regulation at remote loads.
(For LP3965)
Precision Output Voltage: Multiple output voltage options
are available ranging from 1.2V to 5.0V and adjustable
(LP3965), with a guaranteed accuracy of ±1.5% at room
temperature, and ±3.0% over all conditions (varying line,
load, and temperature).
Features
nUltra low dropout voltage
nLow ground pin current
nLoad regulation of 0.04%
n15µA quiescent current in shutdown mode
nGuaranteed output current of 1.5A DC
nAvailable in SOT-223,TO-263 and TO-220 packages
nOutput voltage accuracy ±1.5%
nError flag indicates output status (LP3962)
nSense option improves better load regulation (LP3965)
nExtremely low output capacitor requirements
nOvertemperature/overcurrent protection
n−40˚C to +125˚C junction temperature range
Applications
nMicroprocessor power supplies
nGTL, GTL+, BTL, and SSTL bus terminators
nPower supplies for DSPs
nSCSI terminator
nPost regulators
nHigh efficiency linear regulators
nBattery chargers
nOther battery powered applications
Typical Application Circuits
10126601
*SD and ERROR pins must be pulled high through a 10kΩpull-up resistor. Connect the ERROR pin to ground if this function is not used. See applications
section for more information.
** See Application Hints.
September 2006
LP3962/LP3965 1.5A Fast Ultra Low Dropout Linear Regulators
© 2006 National Semiconductor Corporation DS101266 www.national.com
Typical Application Circuits (Continued)
10126634
*SD and ERROR pins must be pulled high through a 10kΩpull-up resistor. Connect the ERROR pin to ground if this function is not used. See applications section
for more information.
** See Application Hints.
Block Diagram LP3962
10126603
LP3962/LP3965
www.national.com 2
Block Diagram LP3965
10126629
Block Diagram LP3965-ADJ
10126635
LP3962/LP3965
www.national.com3
Connection Diagrams
10126604
Top View
SOT 223-5 Package
10126605
Top View
TO220-5 Package
Bent, Staggered Leads
10126606
Top View
TO263-5 Package
Pin Descriptions for SOT223-5 Package
Pin # LP3962 LP3965
Name Function Name Function
1SD
Shutdown SD Shutdown
2V
IN
Input Supply V
IN
Input Supply
3V
OUT
Output Voltage V
OUT
Output Voltage
4 ERROR ERROR Flag SENSE/ADJ Remote Sense Pin or
Output Adjust Pin
5 GND Ground GND Ground
Pin Descriptions for TO220-5 and TO263-5 Packages
Pin # LP3962 LP3965
Name Function Name Function
1SD
Shutdown SD Shutdown
2V
IN
Input Supply V
IN
Input Supply
3 GND Ground GND Ground
4V
OUT
Output Voltage V
OUT
Output Voltage
5 ERROR ERROR Flag SENSE/ADJ Remote Sense Pin or
Output Adjust Pin
Ordering Information
10126631
Package Type Designator is "MP" for SOT223 package, "T" for TO220 package, and "S" for TO263 package.
LP3962/LP3965
www.national.com 4
Ordering Information (Continued)
TABLE 1. Package Marking and Ordering Information
Output
Voltage Order Number
Description
(Current, Option)
Package
Type Package Marking Supplied As:
5.0 LP3962EMP-5.0 1.5A, Error Flag SOT223-5 LBTB 1000 units on Tape and
Reel
5.0 LP3962EMPX-5.0 1.5A, Error Flag SOT223-5 LBTB 2000 units on Tape and
Reel
3.3 LP3962EMP-3.3 1.5A, Error Flag SOT223-5 LBEB 1000 units on Tape and
Reel
3.3 LP3962EMPX-3.3 1.5A, Error Flag SOT223-5 LBEB 2000 units on Tape and
Reel
2.5 LP3962EMP-2.5 1.5A, Error Flag SOT223-5 LBDB 1000 units on Tape and
Reel
2.5 LP3962EMPX-2.5 1.5A, Error Flag SOT223-5 LBDB 2000 units on Tape and
Reel
1.8 LP3962EMP-1.8 1.5A, Error Flag SOT223-5 LBCB 1000 units on Tape and
Reel
1.8 LP3962EMPX-1.8 1.5A, Error Flag SOT223-5 LBCB 2000 units on Tape and
Reel
5.0 LP3965EMP-5.0 1.5A, SENSE SOT223-5 LBVB 1000 units on Tape and
Reel
5.0 LP3965EMPX-5.0 1.5A, SENSE SOT223-5 LBVB 2000 units on Tape and
Reel
3.3 LP3965EMP-3.3 1.5A, SENSE SOT223-5 LBNB 1000 units on Tape and
Reel
3.3 LP3965EMPX-3.3 1.5A, SENSE SOT223-5 LBNB 2000 units on Tape and
Reel
2.5 LP3965EMP-2.5 1.5A, SENSE SOT223-5 LBLB 1000 units on Tape and
Reel
2.5 LP3965EMPX-2.5 1.5A, SENSE SOT223-5 LBLB 2000 units on Tape and
Reel
1.8 LP3965EMP-1.8 1.5A, SENSE SOT223-5 LBKB 1000 units on Tape and
Reel
1.8 LP3965EMPX-1.8 1.5A, SENSE SOT223-5 LBKB 2000 units on Tape and
Reel
ADJ LP3965EMP-ADJ 1.5A, ADJ SOT223-5 LBRB 1000 units on Tape and
Reel
ADJ LP3965EMPX-ADJ 1.5A, ADJ SOT223-5 LBRB 2000 units on Tape and
Reel
5.0 LP3962ES-5.0 1.5A, Error Flag TO263-5 LP3962ES-5.0 Rail
5.0 LP3962ESX-5.0 1.5A, Error Flag TO263-5 LP3962ESX-5.0 Tape and Reel
3.3 LP3962ES-3.3 1.5A, Error Flag TO263-5 LP3962ES-3.3 Rail
3.3 LP3962ESX-3.3 1.5A, Error Flag TO263-5 LP3962ES-3.3 Tape and Reel
2.5 LP3962ES-2.5 1.5A, Error Flag TO263-5 LP3962ES-2.5 Rail
2.5 LP3962ESX-2.5 1.5A, Error Flag TO263-5 LP3962ES-2.5 Tape and Reel
1.8 LP3962ES-1.8 1.5A, Error Flag TO263-5 LP3962ES-1.8 Rail
1.8 LP3962ESX-1.8 1.5A, Error Flag TO263-5 LP3962ES-1.8 Tape and Reel
5.0 LP3965ES-5.0 1.5A, SENSE TO263-5 LP3965ES-5.0 Rail
5.0 LP3965ESX-5.0 1.5A, SENSE TO263-5 LP3965ES-5.0 Tape and Reel
3.3 LP3965ES-3.3 1.5A, SENSE TO263-5 LP3965ES-3.3 Rail
3.3 LP3965ESX-3.3 1.5A, SENSE TO263-5 LP3965ES-3.3 Tape and Reel
2.5 LP3965ES-2.5 1.5A, SENSE TO263-5 LP3965ES-2.5 Rail
LP3962/LP3965
www.national.com5
Ordering Information (Continued)
TABLE 1. Package Marking and Ordering Information (Continued)
Output
Voltage Order Number
Description
(Current, Option)
Package
Type Package Marking Supplied As:
2.5 LP3965ESX-2.5 1.5A, SENSE TO263-5 LP3965ES-2.5 Tape and Reel
1.8 LP3965ES-1.8 1.5A, SENSE TO263-5 LP3965ES-1.8 Rail
1.8 LP3965ESX-1.8 1.5A, SENSE TO263-5 LP3965ES-1.8 Tape and Reel
ADJ LP3965ES-ADJ 1.5A, ADJ TO263-5 LP3965ES-ADJ Rail
ADJ LP3965ESX-ADJ 1.5A, ADJ TO263-5 LP3965ES-ADJ Tape and Reel
5.0 LP3962ET-5.0 1.5A, Error Flag TO220-5 LP3962ET-5.0 Rail
3.3 LP3962ET-3.3 1.5A, Error Flag TO220-5 LP3962ET-3.3 Rail
2.5 LP3962ET-2.5 1.5A, Error Flag TO220-5 LP3962ET-2.5 Rail
1.8 LP3962ET-1.8 1.5A, Error Flag TO220-5 LP3962ET-1.8 Rail
5.0 LP3965ET-5.0 1.5A, SENSE TO220-5 LP3965ET-5.0 Rail
3.3 LP3965ET-3.3 1.5A, SENSE TO220-5 LP3965ET-3.3 Rail
2.5 LP3965ET-2.5 1.5A, SENSE TO220-5 LP3965ET-2.5 Rail
1.8 LP3965ET-1.8 1.5A, SENSE TO220-5 LP3965ET-1.8 Rail
ADJ LP3965ET-ADJ 1.5A, ADJ TO220-5 LP3965ET-ADJ Rail
LP3962/LP3965
www.national.com 6
Absolute Maximum Ratings (Note 1)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Storage Temperature Range −65˚C to +150˚C
Lead Temperature
(Soldering, 5 sec.) 260˚C
ESD Rating (Note 3) 2 kV
Power Dissipation (Note 2) Internally Limited
Input Supply Voltage (Survival) −0.3V to +7.5V
Shutdown Input Voltage
(Survival) −0.3V to V
IN
+0.3V
Output Voltage (Survival), (Note
6), (Note 7) −0.3V to +7.5V
I
OUT
(Survival) Short Circuit Protected
Maximum Voltage for ERROR
Pin V
IN
+0.3V
Maximum Voltage for SENSE Pin V
OUT
+0.3V
Operating Ratings
Input Supply Voltage (Operating),
(Note 12) 2.5V to 7.0V
Shutdown Input Voltage
(Operating) −0.3V to V
IN
+0.3V
Maximum Operating Current (DC) 1.5A
Operating Junction Temp. Range −40˚C to +125˚C
Electrical Characteristics
LP3962/LP3965
Limits in standard typeface are for T
J
= 25˚C, and limits in boldface type apply over the full operating temperature range.
Unless otherwise specified: V
IN
=V
O(NOM)
+ 1V, I
L
= 10 mA, C
OUT
= 33µF, V
SD
=V
IN
-0.3V.
Symbol Parameter Conditions Typ
(Note 4)
LP3962/5 (Note 5) Units
Min Max
V
O
Output Voltage
Tolerance
(Note 8)
10 mA ≤I
L
≤1.5A
V
OUT
+1 ≤V
IN
≤7.0V 0 -1.5
-3.0
+1.5
+3.0 %
V
ADJ
Adjust Pin Voltage (ADJ
version)
10 mA ≤I
L
≤1.5A
V
OUT
+1.5V ≤V
IN
≤7.0V 1.216 1.198
1.180
1.234
1.253 V
∆V
OL
Output Voltage Line
Regulation (Note 8)
V
OUT
+1V<V
IN
<7.0V, 0.02
0.06
%
∆V
O
/∆I
OUT
Output Voltage Load
Regulation
(Note 8)
10 mA <I
L
<1.5 A 0.04
0.09
%
V
IN
-V
OUT
Dropout Voltage
(Note 10)
I
L
= 150 mA 38 45
55 mV
I
L
= 1.5 A 380 450
550
I
GND
Ground Pin Current In
Normal Operation Mode
I
L
= 150 mA 4 9
10 mA
I
L
= 1.5 A 5 14
15
I
GND
Ground Pin Current In
Shutdown Mode
(Note 11)
V
SD
≤0.2V 15 25
75
µA
I
O(PK)
Peak Output Current (Note 2) 2.5 2.0
1.7
A
SHORT CIRCUIT PROTECTION
I
SC
Short Circuit Current 4.5 A
OVER TEMPERATURE PROTECTION
Tsh(t) Shutdown Threshold 165 ˚C
Tsh(h) Thermal Shutdown
Hysteresis
10 ˚C
SHUTDOWN INPUT
V
SDT
Shutdown Threshold Output = High V
IN
V
IN
–0.3 V
Output = Low 0 0.2
LP3962/LP3965
www.national.com7
Electrical Characteristics
LP3962/LP3965 (Continued)
Limits in standard typeface are for T
J
= 25˚C, and limits in boldface type apply over the full operating temperature range.
Unless otherwise specified: V
IN
=V
O(NOM)
+ 1V, I
L
= 10 mA, C
OUT
= 33µF, V
SD
=V
IN
-0.3V.
Symbol Parameter Conditions Typ
(Note 4)
LP3962/5 (Note 5) Units
Min Max
T
dOFF
Turn-off delay I
L
= 1.5 A 20 µs
T
dON
Turn-on delay I
L
= 1.5 A 25 µs
I
SD
SD Input Current V
SD
=V
IN
1nA
ERROR FLAG COMPARATOR
V
T
Threshold (Note 9) 10 516%
V
TH
Threshold Hysteresis (Note 9) 5 28%
V
EF(Sat)
Error Flag Saturation I
sink
= 100µA 0.02 0.1 V
Td Flag Reset Delay 1 µs
I
lk
Error Flag Pin Leakage
Current
1nA
I
max
Error Flag Pin Sink
Current
V
Error
=0.5V (over temp.) 1 mA
AC PARAMETERS
PSRR Ripple Rejection
V
IN
=V
OUT
+ 1.5V
C
OUT
= 100uF
V
OUT
= 3.3V
60
dB
V
IN
=V
OUT
+ 0.3V
C
OUT
= 100uF
V
OUT
= 3.3V
40
ρ
n(l/f
Output Noise Density f = 120Hz 0.8 µV
e
n
Output Noise Voltage
(rms)
BW = 10Hz – 100kHz 150 µV (rms)
BW = 300Hz – 300kHz 100
Note 1: Absolute maximum ratings indicate limits beyond which damage to the device may occur. Operating ratings indicate conditions for which the device is
intended to be functional, but does not guarantee specific performance limits. For guaranteed specifications and test conditions, see Electrical Charateristics. The
guaranteed specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed
test conditions.
Note 2: At elevated temperatures, devices must be derated based on package thermal resistance. The devices in TO220 package must be derated at θjA = 50˚C/W
(with 0.5in2, 1oz. copper area), junction-to-ambient (with no heat sink). The devices in the TO263 surface-mount package must be derated at θjA = 60˚C/W (with
0.5in2, 1oz. copper area), junction-to-ambient. The devices in SOT223 package must be derated at θjA = 90˚C/W (with 0.5in2, 1oz. copper area), junction-to-ambient.
Note 3: The human body model is a 100pF capacitor discharged through a 1.5kΩresistor into each pin.
Note 4: Typical numbers are at 25˚C and represent the most likely parametric norm.
Note 5: Limits are 100% production tested at 25˚C. Limits over the operating temperature range are guaranteed through correlation using Statistical Quality Control
(SQC) methods. The limits are used to calculate National’s Average Outgoing Quality Level (AOQL).
Note 6: If used in a dual-supply system where the regulator load is returned to a negative supply, the LP396X output must be diode-clamped to ground.
Note 7: The output PMOS structure contains a diode between the VIN and VOUT terminals. This diode is normally reverse biased. This diode will get forward biased
if the voltage at the output terminal is forced to be higher than the voltage at the input terminal. This diode can typically withstand 200mA of DC current and 1Amp
of peak current.
Note 8: Output voltage line regulation is defined as the change in output voltage from the nominal value due to change in the input line voltage. Output voltage load
regulation is defined as the change in output voltage from the nominal value due to change in load current. The line and load regulation specification contains only
the typical number. However, the limits for line and load regulation are included in the output voltage tolerance specification.
Note 9: Error Flag threshold and hysteresis are specified as percentage of regulated output voltage.
Note 10: Dropout voltage is defined as the minimum input to output differential voltage at which the output drops 2% below the nominal value. Dropout voltage
specification applies only to output voltages of 2.5V and above. For output voltages below 2.5V, the drop-out voltage is nothing but the input to output differential,
since the minimum input voltage is 2.5V.
Note 11: This specification has been tested for −40˚C ≤TJ≤85˚C since the temperature rise of the device is negligible under shutdown conditions.
Note 12: The minimum operating value for VIN is equal to either [VOUT(NOM) +V
DROPOUT] or 2.5V, whichever is greater.
LP3962/LP3965
www.national.com 8
Typical Performance Characteristics Unless otherwise specified, V
IN
=V
O(NOM)
+ 1V, V
OUT
= 2.5V,
C
OUT
= 33µF, I
OUT
= 10mA, C
IN
= 68µF, V
SD
=V
IN
, and T
A
= 25˚C.
Drop-Out Voltage vs Temperature for Different Load
Currents
Drop-Out Voltage vs Temperature for Different Output
Voltages (I
OUT
= 800mA
10126609 10126610
Ground Pin Current vs Input Voltage (V
SD
=V
IN
) Ground Pin Current vs Input Voltage (V
SD
=100mV)
10126611 10126615
Ground Current vs Temperature (V
SD
=V
IN
) Ground Current vs Temperature (V
SD
=0V
10126618 10126612
LP3962/LP3965
www.national.com9
Typical Performance Characteristics Unless otherwise specified, V
IN
=V
O(NOM)
+ 1V, V
OUT
= 2.5V,
COUT = 33µF, I
OUT
= 10mA, C
IN
= 68µF, V
SD
=V
IN
, and T
A
= 25˚C. (Continued)
Ground Pin Current vs Shutdown Pin Voltage Input Voltage vs Output Voltage
10126616 10126617
Output Noise Density, V
OUT
= 2.5V Output Noise Density, V
OUT
=5V
10126613 10126614
Load Transient Response Ripple Rejection vs Frequency
10126637
10126638
LP3962/LP3965
www.national.com 10
Typical Performance Characteristics Unless otherwise specified, V
IN
=V
O(NOM)
+ 1V, V
OUT
= 2.5V,
COUT = 33µF, I
OUT
= 10mA, C
IN
= 68µF, V
SD
=V
IN
, and T
A
= 25˚C. (Continued)
δV
OUT
vs Temperature Noise Density V
IN
= 3.5V, V
OUT
= 2.5V, I
L
=10mA
10126639 10126640
Line Transient Response Line Transient Response
10126641 10126642
Line Transient Response (I
OUT
= 1.5A) Line Transient Response (I
OUT
= 1.5A)
10126643 10126644
LP3962/LP3965
www.national.com11
Applications Information
EXTERNAL CAPACITORS
Like any low-dropout regulator, external capacitors are re-
quired to assure stability. these capacitors must be correctly
selected for proper performance.
INPUT CAPACITOR: The LP3962/5 requires a low source
impedance to maintain regulator stability because the inter-
nal bias circuitry is connected directly to V
IN
. The input
capacitor must be located less than 1 cm from the LP3962/5
device and connected directly to the input and ground pins
using traces which have no other currents flowing through
them (see PCB Layout section).
The minimum allowable input capacitance for a given appli-
cation depends on the type of the capacitor and ESR
(equivalent series resistance). A lower ESR capacitor allows
the use of less capacitance, while higher ESR types (like
aluminum electrolytics) require more capacitance.
The lowest value of input capacitance that can be used for
stable full-load operation is 68 µF (assuming it is a ceramic
or low-ESR Tantalum with ESR less than 100 mΩ).
To determine the minimum input capacitance amount and
ESR value, an approximation which should be used is:
C
IN
ESR (mΩ)/C
IN
(µF) ≤1.5
This shows that input capacitors with higher ESR values can
be used if sufficient total capacitance is provided. Capacitor
types (aluminum, ceramic, and tantalum) can be mixed in
parallel, but the total equivalent input capacitance/ESR must
be defined as above to assure stable operation.
IMPORTANT: The input capacitor must maintain its ESR and
capacitance in the "stable range" over the entire temperature
range of the application to assure stability (see Capacitor
Characteristics Section).
OUTPUT CAPACITOR: An output capacitor is also required
for loop stability. It must be located less than 1 cm from the
LP3962/5 device and connected directly to the output and
ground pins using traces which have no other currents flow-
ing through them (see PCB Layout section).
The minimum value of the output capacitance that can be
used for stable full-load operation is 33 µF, but it may be
increased without limit. The output capacitor’s ESR is critical
because it forms a zero to provide phase lead which is
required for loop stability. The ESR must fall within the
specified range:
0.2Ω≤C
OUT
ESR ≤5Ω
The lower limit of 200 mΩmeans that ceramic capacitors are
not suitable for use as LP3962/5 output capacitors (but can
be used on the input). Some ceramic capacitance can be
used on the output if the total equivalent ESR is in the stable
range: when using a 100 µF Tantalum as the output capaci-
tor, approximately 3 µF of ceramic capacitance can be ap-
plied before stability becomes marginal.
IMPORTANT: The output capacitor must meet the require-
ments for minimum amount of capacitance and also have an
appropriate ESR value over the full temperature range of the
application to assure stability (see Capacitor Characteristics
Section).
SELECTING A CAPACITOR
It is important to note that capacitance tolerance and varia-
tion with temperature must be taken into consideration when
selecting a capacitor so that the minimum required amount
of capacitance is provided over the full operating tempera-
ture range. In general, a good Tantalum capacitor will show
very little capacitance variation with temperature, but a ce-
ramic may not be as good (depending on dielectric type).
Aluminum electrolytics also typically have large temperature
variation of capacitance value.
Equally important to consider is a capacitor’s ESR change
with temperature: this is not an issue with ceramics, as their
ESR is extremely low. However, it is very important in Tan-
talum and aluminum electrolytic capacitors. Both show in-
creasing ESR at colder temperatures, but the increase in
aluminum electrolytic capacitors is so severe they may not
be feasible for some applications (see Capacitor Character-
istics Section).
CAPACITOR CHARACTERISTICS
CERAMIC: For values of capacitance in the 10 to 100 µF
range, ceramics are usually larger and more costly than
tantalums but give superior AC performance for bypassing
high frequency noise because of very low ESR (typically less
than 10 mΩ). However, some dielectric types do not have
good capacitance characteristics as a function of voltage
and temperature.
Z5U and Y5V dielectric ceramics have capacitance that
drops severely with applied voltage. A typical Z5U or Y5V
capacitor can lose 60% of its rated capacitance with half of
the rated voltage applied to it. The Z5U and Y5V also exhibit
a severe temperature effect, losing more than 50% of nomi-
nal capacitance at high and low limits of the temperature
range.
X7R and X5R dielectric ceramic capacitors are strongly rec-
ommended if ceramics are used, as they typically maintain a
capacitance range within ±20% of nominal over full operat-
ing ratings of temperature and voltage. Of course, they are
typically larger and more costly than Z5U/Y5U types for a
given voltage and capacitance.
TANTALUM: Solid Tantalum capacitors are recommended
for use on the output because their typical ESR is very close
to the ideal value required for loop compensation. They also
work well as input capacitors if selected to meet the ESR
requirements previously listed.
Tantalums also have good temperature stability: a good
quality Tantalum will typically show a capacitance value that
varies less than 10-15% across the full temperature range of
125˚C to −40˚C. ESR will vary only about 2X going from the
high to low temperature limits.
The increasing ESR at lower temperatures can cause oscil-
lations when marginal quality capacitors are used (if the ESR
of the capacitor is near the upper limit of the stability range at
room temperature).
ALUMINUM: This capacitor type offers the most capaci-
tance for the money. The disadvantages are that they are
larger in physical size, not widely available in surface mount,
and have poor AC performance (especially at higher fre-
quencies) due to higher ESR and ESL.
Compared by size, the ESR of an aluminum electrolytic is
higher than either Tantalum or ceramic, and it also varies
greatly with temperature. A typical aluminum electrolytic can
exhibit an ESR increase of as much as 50X when going from
25˚C down to −40˚C.
It should also be noted that many aluminum electrolytics only
specify impedance at a frequency of 120 Hz, which indicates
they have poor high frequency performance. Only aluminum
electrolytics that have an impedance specified at a higher
frequency (between 20 kHz and 100 kHz) should be used for
LP3962/LP3965
www.national.com 12
Applications Information (Continued)
the LP396X. Derating must be applied to the manufacturer’s
ESR specification, since it is typically only valid at room
temperature.
Any applications using aluminum electrolytics should be
thoroughly tested at the lowest ambient operating tempera-
ture where ESR is maximum.
PCB LAYOUT
Good PC layout practices must be used or instability can be
induced because of ground loops and voltage drops. The
input and output capacitors must be directly connected to the
input, output, and ground pins of the LP3962/5 using traces
which do not have other currents flowing in them Kelvin
connect).
The best way to do this is to lay out C
IN
and C
OUT
near the
device with short traces to the V
IN
,V
OUT
, and ground pins.
The regulator ground pin should be connected to the exter-
nal circuit ground so that the regulator and its capacitors
have a "single point ground".
It should be noted that stability problems have been seen in
applications where "vias" to an internal ground plane were
used at the ground points of the LP3962/5 IC and the input
and output capacitors. This was caused by varying ground
potentials at these nodes resulting from current flowing
through the ground plane. Using a single point ground tech-
nique for the regulator and it’s capacitors fixed the problem.
Since high current flows through the traces going into V
IN
and coming from V
OUT
, Kelvin connect the capacitor leads to
these pins so there is no voltage drop in series with the input
and output capacitors.
RFI/EMI SUSCEPTIBILITY
RFI (radio frequency interference) and EMI (electromagnetic
interference) can degrade any integrated circuit’s perfor-
mance because of the small dimensions of the geometries
inside the device. In applications where circuit sources are
present which generate signals with significant high fre-
quency energy content (>1 MHz), care must be taken to
ensure that this does not affect the IC regulator.
If RFI/EMI noise is present on the input side of the LP396X
regulator (such as applications where the input source
comes from the output of a switching regulator), good ce-
ramic bypass capacitors must be used at the input pin of the
LP396X.
If a load is connected to the LP396X output which switches
at high speed (such as a clock), the high-frequency current
pulses required by the load must be supplied by the capaci-
tors on the LP396X output. Since the bandwidth of the
regulator loop is less than 100 kHz, the control circuitry
cannot respond to load changes above that frequency. The
means the effective output impedance of the LP396X at
frequencies above 100 kHz is determined only by the output
capacitor(s).
In applications where the load is switching at high speed, the
output of the LP396X may need RF isolation from the load. It
is recommended that some inductance be placed between
the LP396X output capacitor and the load, and good RF
bypass capacitors be placed directly across the load.
PCB layout is also critical in high noise environments, since
RFI/EMI is easily radiated directly into PC traces. Noisy
circuitry should be isolated from "clean" circuits where pos-
sible, and grounded through a separate path. At MHz fre-
quencies, ground planes begin to look inductive and RFI/
EMI can cause ground bounce across the ground plane.
In multi-layer PCB applications, care should be taken in
layout so that noisy power and ground planes do not radiate
directly into adjacent layers which carry analog power and
ground.
OUTPUT ADJUSTMENT
An adjustable output device has output voltage range of
1.216V to 5.1V. To obtain a desired output voltage, the
following equation can be used with R1 always a 10kΩ
resistor.
For output stability, C
F
must be between 68pF and 100pF.
TURN-ON CHARACTERISTICS FOR OUTPUT
VOLTAGES PROGRAMMED TO 2.0V OR BELOW
As Vin increases during start-up, the regulator output will
track the input until Vin reaches the minimum operating
voltage (typically about 2.2V). For output voltages pro-
grammed to 2.0V or below, the regulator output may mo-
mentarily exceed its programmed output voltage during start
up. Outputs programmed to voltages above 2.0V are not
affected by this behavior.
OUTPUT NOISE
Noise is specified in two ways-
Spot Noise or Output noise density is the RMS sum of all
noise sources, measured at the regulator output, at a spe-
cific frequency (measured with a 1Hz bandwidth). This type
of noise is usually plotted on a curve as a function of fre-
quency.
Total output Noise or Broad-band noise is the RMS sum
of spot noise over a specified bandwidth, usually several
decades of frequencies.
Attention should be paid to the units of measurement. Spot
noise is measured in units µV/√Hz or nV/√Hz and total output
noise is measured in µV(rms).
The primary source of noise in low-dropout regulators is the
internal reference. In CMOS regulators, noise has a low
frequency component and a high frequency component,
which depend strongly on the silicon area and quiescent
current. Noise can be reduced in two ways: by increasing the
transistor area or by increasing the current drawn by the
internal reference. Increasing the area will decrease the
chance of fitting the die into a smaller package. Increasing
the current drawn by the internal reference increases the
total supply current (ground pin current). Using an optimized
trade-off of ground pin current and die size, LP3962/LP3965
achieves low noise performance and low quiescent current
operation.
The total output noise specification for LP3962/LP3965 is
presented in the Electrical Characteristics table. The Output
noise density at different frequencies is represented by a
curve under typical performance characteristics.
SHORT-CIRCUIT PROTECTION
The LP3962and LP3965 is short circuit protected and in the
event of a peak over-current condition, the short-circuit con-
trol loop will rapidly drive the output PMOS pass element off.
LP3962/LP3965
www.national.com13
Applications Information (Continued)
Once the power pass element shuts down, the control loop
will rapidly cycle the output on and off until the average
power dissipation causes the thermal shutdown circuit to
respond to servo the on/off cycling to a lower frequency.
Please refer to the section on thermal information for power
dissipation calculations.
ERROR FLAG OPERATION
The LP3962/LP3965 produces a logic low signal at the Error
Flag pin when the output drops out of regulation due to low
input voltage, current limiting, or thermal limiting. This flag
has a built in hysteresis. The timing diagram in Figure 1
shows the relationship between the ERROR and the output
voltage. In this example, the input voltage is changed to
demonstrate the functionality of the Error Flag.
The internal Error flag comparator has an open drain output
stage. Hence, the ERROR pin should be pulled high through
a pull up resistor. Although the ERROR pin can sink current
of 1mA, this current is energy drain from the input supply.
Hence, the value of the pull up resistor should be in the
range of 10kΩto 1MΩ.The ERROR pin must be con-
nected to ground if this function is not used. It should
also be noted that when the shutdown pin is pulled low, the
ERROR pin is forced to be invalid for reasons of saving
power in shutdown mode.
SENSE PIN
In applications where the regulator output is not very close to
the load, LP3965 can provide better remote load regulation
using the SENSE pin. Figure 2 depicts the advantage of the
SENSE option. LP3962 regulates the voltage at the output
pin. Hence, the voltage at the remote load will be the regu-
lator output voltage minus the drop across the trace resis-
tance. For example, in the case of a 3.3V output, if the trace
resistance is 100mΩ, the voltage at the remote load will be
3.15V with 1.5 A of load current, I
LOAD
. The LP3965 regu-
lates the voltage at the sense pin. Connecting the sense pin
to the remote load will provide regulation at the remote load,
as shown in Figure 2. If the sense option pin is not required,
the sense pin must be connected to the V
OUT
pin.
10126607
FIGURE 1. Error Flag Operation
LP3962/LP3965
www.national.com 14
Applications Information (Continued)
SHUTDOWN OPERATION
A CMOS Logic level signal at the shutdown ( SD) pin will
turn-off the regulator. Pin SD must be actively terminated
through a 10kΩpull-up resistor for a proper operation. If this
pin is driven from a source that actively pulls high and low
(such as a CMOS rail to rail comparator), the pull-up resistor
is not required. This pin must be tied to Vin if not used.
DROPOUT VOLTAGE
The dropout voltage of a regulator is defined as the minimum
input-to-output differential required to stay within 2% of the
output voltage. The LP3962/LP3965 use an internal MOS-
FET with an Rds(on) of 240mΩ(typically). For CMOS LDOs,
the dropout voltage is the product of the load current and the
Rds(on) of the internal MOSFET.
REVERSE CURRENT PATH
The internal MOSFET in LP3962and LP3965 has an inher-
ent parasitic diode. During normal operation, the input volt-
age is higher than the output voltage and the parasitic diode
is reverse biased. However, if the output is pulled above the
input in an application, then current flows from the output to
the input as the parasitic diode gets forward biased. The
output can be pulled above the input as long as the current
in the parasitic diode is limited to 200mA continuous and 1A
peak.
MAXIMUM OUTPUT CURRENT CAPABILITY
LP3962 and LP3965 can deliver a continuous current of 1.5
A over the full operating temperature range. A heatsink may
be required depending on the maximum power dissipation
and maximum ambient temperature of the application. Under
all possible conditions, the junction temperature must be
within the range specified under operating conditions. The
total power dissipation of the device is given by:
P
D
=(V
IN
−V
OUT
)I
OUT
+(V
IN
)I
GND
where I
GND
is the operating ground current of the device
(specified under Electrical Characteristics).
The maximum allowable temperature rise (T
Rmax
) depends
on the maximum ambient temperature (T
Amax
) of the appli-
cation, and the maximum allowable junction temperature(T
J-
max
):
T
Rmax
=T
Jmax
−T
Amax
The maximum allowable value for junction to ambient Ther-
mal Resistance, θ
JA
, can be calculated using the formula:
θ
JA
=T
Rmax
/P
D
LP3962 and LP3965 are available in TO-220, TO-263, and
SOT-223 packages. The thermal resistance depends on
amount of copper area or heat sink, and on air flow. If the
maximum allowable value of θ
JA
calculated above is ≥60
˚C/W for TO-220 package, ≥60 ˚C/W for TO-263 package,
and ≥140 ˚C/W for SOT-223 package, no heatsink is
needed since the package can dissipate enough heat to
satisfy these requirements. If the value for allowable θ
JA
falls
below these limits, a heat sink is required.
HEATSINKING TO-220 PACKAGES
The thermal resistance of a TO220 package can be reduced
by attaching it to a heat sink or a copper plane on a PC
board. If a copper plane is to be used, the values of θ
JA
will
be same as shown in next section for TO263 package.
The heatsink to be used in the application should have a
heatsink to ambient thermal resistance,
θ
HA
≤θ
JA
−θ
CH
−θ
JC
.
In this equation, θ
CH
is the thermal resistance from the
junction to the surface of the heat sink and θ
JC
is the thermal
resistance from the junction to the surface of the case. θ
JC
is
about 3˚C/W for a TO220 package. The value for θ
CH
de-
pends on method of attachment, insulator, etc. θ
CH
varies
between 1.5˚C/W to 2.5˚C/W. If the exact value is unknown,
2˚C/W can be assumed.
10126608
FIGURE 2. Improving remote load regulation using LP3965
LP3962/LP3965
www.national.com15
Applications Information (Continued)
HEATSINKING TO-263 AND SOT-223 PACKAGES
The TO-263 and SOT223 packages use the copper plane on
the PCB as a heatsink. The tab of these packages are
soldered to the copper plane for heat sinking. Figure 3
shows a curve for the θ
JA
of TO-263 package for different
copper area sizes, using a typical PCB with 1 ounce copper
and no solder mask over the copper area for heat sinking.
As shown in the figure, increasing the copper area beyond 1
square inch produces very little improvement. The minimum
value for θ
JA
for the TO-263 packag mounted to a PCB is
32˚C/W.
Figure 4 shows the maximum allowable power dissipation
for TO-263 packages for different ambient temperatures,
assuming θ
JA
is 35˚C/W and the maximum junction tempera-
ture is 125˚C.
Figure 5 shows a curve for the θ
JA
of SOT-223 package for
different copper area sizes, using a typical PCB with 1 ounce
copper and no solder mask over the copper area for heat
sinking.
The following figures show different layout scenarios for
SOT-223 package.
10126632
FIGURE 3. θ
JA
vs Copper(1 Ounce) Area for TO-263
package
10126633
FIGURE 4. Maximum power dissipation vs ambient
temperature for TO-263 package
10126619
FIGURE 5. θ
JA
vs Copper(1 Ounce) Area for SOT-223
package
10126620
FIGURE 6. SCENARIO A, θ
JA
= 148˚C/W
10126621
FIGURE 7. SCENARIO B, θ
JA
= 125˚C/W
LP3962/LP3965
www.national.com 16
Applications Information (Continued)
10126622
FIGURE 8. SCENARIO C, θ
JA
= 92˚C/W
10126623
FIGURE 9. SCENARIO D, θ
JA
= 83˚C/W
10126624
FIGURE 10. SCENARIO E, θ
JA
= 77˚C/W
10126625
FIGURE 11. SCENARIO F, θ
JA
= 75˚C/W
LP3962/LP3965
www.national.com17
10126626
FIGURE 12. SCENARIO G, θ
JA
= 113˚C/W
10126627
FIGURE 13. SCENARIO H, θ
JA
= 79˚C/W
LP3962/LP3965
www.national.com 18
Applications Information (Continued)
10126628
FIGURE 14. SCENARIO I, θ
JA
= 78.5˚C/W
LP3962/LP3965
www.national.com19
Physical Dimensions inches (millimeters) unless otherwise noted
TO220 5-lead, Molded, Stagger Bend Package (TO220-5)
NS Package Number T05D
For Order Numbers, refer to the “Ordering Information” section of this document.
LP3962/LP3965
www.national.com 20
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
TO263 5-Lead, Molded, Surface Mount Package (TO263-5)
NS Package Number TS5B
For Order Numbers, refer to the “Ordering Information” section of this document.
LP3962/LP3965
www.national.com21
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
SOT223, 5-Lead, Molded, Surface Mount Package (SOT223-5)
NS Package Number MP05A
For Order Numbers, refer to the “Ordering Information” section of this document.
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves
the right at any time without notice to change said circuitry and specifications.
For the most current product information visit us at www.national.com.
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS
WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR
CORPORATION. As used herein:
1. Life support devices or systems are devices or systems
which, (a) are intended for surgical implant into the body, or
(b) support or sustain life, and whose failure to perform when
properly used in accordance with instructions for use
provided in the labeling, can be reasonably expected to result
in a significant injury to the user.
2. A critical component is any component of a life support
device or system whose failure to perform can be reasonably
expected to cause the failure of the life support device or
system, or to affect its safety or effectiveness.
BANNED SUBSTANCE COMPLIANCE
National Semiconductor follows the provisions of the Product Stewardship Guide for Customers (CSP-9-111C2) and Banned Substances
and Materials of Interest Specification (CSP-9-111S2) for regulatory environmental compliance. Details may be found at:
www.national.com/quality/green.
Lead free products are RoHS compliant.
National Semiconductor
Americas Customer
Support Center
Email: new.feedback@nsc.com
Tel: 1-800-272-9959
National Semiconductor
Europe Customer Support Center
Fax: +49 (0) 180-530 85 86
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
National Semiconductor
Asia Pacific Customer
Support Center
Email: ap.support@nsc.com
National Semiconductor
Japan Customer Support Center
Fax: 81-3-5639-7507
Email: jpn.feedback@nsc.com
Tel: 81-3-5639-7560
www.national.com
LP3962/LP3965 1.5A Fast Ultra Low Dropout Linear Regulators
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic."Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products Applications
Audio www.ti.com/audio Communications and Telecom www.ti.com/communications
Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers
Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps
DLP®Products www.dlp.com Energy and Lighting www.ti.com/energy
DSP dsp.ti.com Industrial www.ti.com/industrial
Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical
Interface interface.ti.com Security www.ti.com/security
Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Mobile Processors www.ti.com/omap
Wireless Connectivity www.ti.com/wirelessconnectivity
TI E2E Community Home Page e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright ©2011, Texas Instruments Incorporated
