PF993-02 Micro MINI S1C60N09 4-bit Single Chip Microcomputer ge oltan V o Lowerati ts p c u O od Pr S1C6200B Core CPU Low Voltage and Low Power Built-in LCD Driver Low Cost Performance DESCRIPTION The S1C60N09 Series single-chip microcomputer features an S1C6200B CMOS 4-bit CPU as the core. It contains a 1,536 (words) x 12 (bits) ROM, 144 (words) x 4 (bits) RAM, LCD driver, 4-bit input port (K00-K03), 4bit output port (R00-R03), 8-bit I/O port (P00-P03, P10-P13) and timers. The S1C60N09 Series is configured as follows, depending on the supply voltage. S1C60N09: 3.0 V (2.6 to 3.6 V) S1C60L09: 1.5 V (1.2 to 1.8 V) FEATURES Core CPU ................................................... S1C6200B Built-in oscillation circuit ............................. Crystal 32.768 kHz (Typ.) or CR oscillation circuit 65 kHz (Typ.) Instruction set ............................................. 100 instructions ROM capacity ............................................ 1,536 words x 12 bits RAM capacity ............................................. 144 words x 4 bits Input port .................................................... 4 bits (pull-down resistors are available by mask option) Output port ................................................. 4 bits (clock and buzzer outputs are selectable by mask option) I/O port ....................................................... 8 bits LCD driver .................................................. 38 segments x 4, 3 or 2 commons (1/4, 1/3 or 1/2 duty are selectable by mask option) Time base counter ..................................... 2 systems (clock timer and stopwatch timer) built-in Interrupt ...................................................... External: Input port interrupt Internal: Timer interrupt 1 system 2 systems Supply voltage ........................................... 1.5 V (1.2 to 1.8 V) S1C60L09 3.0 V (2.6 to 3.6 V) S1C60N09 Current consumption (Typ.) ....................... During HALT: 1.0 A (32 kHz crystal oscillation) During execution: 3.0 A (32 kHz crystal oscillation) Supply form ................................................ Die form only 1 S1C60N09 RESET ROM 1,536 words x 12 bits OSC1 OSC2 BLOCK DIAGRAM OSC System Reset Control Core CPU S1C6200B RAM Interrupt Generator 144 words x 4 bits K00-K03 COM0-3 SEG0-37 Input Port LCD Driver TEST 38 SEG x 4 COM Output Port VDD VL1-VL3 CA, CB VS1 VSS Power Controller I/O Port Stopwatch Timer Clock Timer R00, R03 (BZ, BZ)1 R01 R02 (FOUT)1 P00-P03 P10-P13 1: Terminal specifications can be selected by mask option. PAD LAYOUT Pad Layout Diagram 15 Pad Coordinates 10 5 1 70 20 65 25 30 X 60 Die No. (0, 0) 55 35 40 45 50 2.90mm Chip thickness: 400m Pad opening: 95m 2 2.87mm Y No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 Pad name SEG37 K03 K02 K01 K00 P13 P12 P11 P10 P03 P02 P01 P00 R02 R01 R00 R03 VSS RESET VS1 OSC2 OSC1 VDD VL3 VL2 VL1 CB CA COM3 COM2 COM1 COM0 SEG0 SEG1 SEG2 (Unit: m) X Y 1,020 1,268 861 1,268 731 1,268 601 1,268 471 1,268 297 1,268 167 1,268 37 1,268 -93 1,268 -246 1,268 -376 1,268 -507 1,268 -637 1,268 -835 1,268 -969 1,268 -1,102 1,268 -1,236 1,268 -1,284 965 -1,284 835 -1,284 705 -1,284 575 -1,284 445 -1,284 286 -1,284 156 -1,284 26 -1,284 -104 -1,284 -234 -1,284 -364 -1,284 -494 -1,284 -624 -1,284 -754 -1,284 -884 -1,284 -1,014 -1,237 -1,268 -1,107 -1,268 No. 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 Pad name SEG3 SEG4 SEG5 SEG6 SEG7 SEG8 SEG9 SEG10 SEG11 SEG12 SEG13 SEG14 SEG15 SEG16 SEG17 SEG18 SEG19 TEST SEG20 SEG21 SEG22 SEG23 SEG24 SEG25 SEG26 SEG27 SEG28 SEG29 SEG30 SEG31 SEG32 SEG33 SEG34 SEG35 SEG36 X -977 -795 -665 -535 -405 -275 -145 -15 115 245 375 505 635 765 895 1,025 1,284 1,284 1,284 1,284 1,284 1,284 1,284 1,284 1,284 1,284 1,284 1,284 1,284 1,284 1,284 1,284 1,284 1,284 1,284 Y -1,268 -1,268 -1,268 -1,268 -1,268 -1,268 -1,268 -1,268 -1,268 -1,268 -1,268 -1,268 -1,268 -1,268 -1,268 -1,268 -1,196 -1,037 -879 -749 -619 -489 -359 -229 -99 32 162 292 422 552 682 812 942 1,072 1,202 S1C60N09 PAD DESCRIPTION Pad name Pad No. VDD 23 VSS 18 VS1 20 VL1-3 26-24 CA, CB 28, 27 OSC1 22 OSC2 21 K00-03 5-2 P00-03 13-10 P10-13 9-6 R00 16 R03 17 R01 15 R02 14 SEG0-37 33-52, 54-70, 1 COM0-3 32-29 RESET 19 TEST 53 Can be selected by mask option I/O (I) (I) - - - I O I I/O I/O O O O O O O I I Function Power supply terminal (+) Power supply terminal (-) Constant voltage output terminal Power source for LCD Booster capacitor connecting terminal Crystal or CR oscillation input terminal Crystal or CR oscillation output terminal Input port terminal I/O port terminal I/O port terminal Output port terminal (BZ output is selectable ) Output port terminal (BZ output is selectable ) Output port terminal Output port terminal (FOUT output is selectable ) LCD segment output (DC output is selectable ) LCD common output terminal (1/4, 1/3 or 1/2 duty are selectable ) Initial reset input terminal Test input terminal OPTION LIST 1. DEVICE TYPE 1. E0C6009 2. E0C6009 3. E0C60L09 4. E0C60L09 (S1C60N09) (S1C60N09) (S1C60L09) (S1C60L09) LCD LCD LCD LCD 3V 4.5 V 3V 4.5 V 2. OSC1 SYSTEM CLOCK 1. Crystal 2. CR 3. MULTIPLE KEY ENTRY RESET * KEY COMBINATION ................... 1. Not Use 2. Use K00, K01 3. Use K00, K01, K02 4. Use K00, K01, K02, K03 4. INTERRUPT NOISE REJECTOR K00-K03 1. Use 2. Not Use 5. INPUT PORT PULL DOWN RESISTOR * K00 ............................................... 1. With Resistor * K01 ............................................... 1. With Resistor * K02 ............................................... 1. With Resistor * K03 ............................................... 1. With Resistor 6. R00 SPECIFICATION * R00 OUTPUT SPECIFICATION .. 1. Complementary * R00 OUTPUT TYPE .................... 1. DC Output 2. Pch-OpenDrain 2. Buzzer Output 7. R01 SPECIFICATION * R01 OUTPUT SPECIFICATION .. 1. Complementary 2. Pch-OpenDrain 2. Gate Direct 2. Gate Direct 2. Gate Direct 2. Gate Direct 3 S1C60N09 8. R02 SPECIFICATION * R02 OUTPUT SPECIFICATION .. 1. Complementary * R02 OUTPUT TYPE .................... 1. DC Output 2. FOSC1 3. FOSC1/2 4. FOSC1/4 5. FOSC1/8 6. FOSC1/16 7. FOSC1/32 8. FOSC1/64 9. FOSC1/128 2. Pch-OpenDrain 9. R03 SPECIFICATION * R03 OUTPUT SPECIFICATION .. 1. Complementary 2. Pch-OpenDrain * R03 OUTPUT TYPE .................... 1. DC Output 2. Buzzer Output (R00 control) 3. Buzzer Output (R03 control) 10. I/O PORT SPECIFICATION * P00 .............................................. * P01 .............................................. * P02 .............................................. * P03 .............................................. * P10 .............................................. * P11 .............................................. * P12 .............................................. * P13 .............................................. 1. Complementary 1. Complementary 1. Complementary 1. Complementary 1. Complementary 1. Complementary 1. Complementary 1. Complementary 2. Pch-OpenDrain 2. Pch-OpenDrain 2. Pch-OpenDrain 2. Pch-OpenDrain 2. Pch-OpenDrain 2. Pch-OpenDrain 2. Pch-OpenDrain 2. Pch-OpenDrain 11. I/O PORT PULL DOWN RESISTOR * P00 .............................................. * P01 .............................................. * P02 .............................................. * P03 .............................................. * P10 .............................................. * P11 .............................................. * P12 .............................................. * P13 .............................................. 1. With Resistor 1. With Resistor 1. With Resistor 1. With Resistor 1. With Resistor 1. With Resistor 1. With Resistor 1. With Resistor 2. Gate Direct 2. Gate Direct 2. Gate Direct 2. Gate Direct 2. Gate Direct 2. Gate Direct 2. Gate Direct 2. Gate Direct 12. I/O PORT FUNCTION * P00 .............................................. * P01 .............................................. * P02 .............................................. * P03 .............................................. * P10 .............................................. * P11 .............................................. * P12 .............................................. * P13 .............................................. 1. I/O Port 1. I/O Port 1. I/O Port 1. I/O Port 1. I/O Port 1. I/O Port 1. I/O Port 1. I/O Port 2. Output Port 2. Output Port 2. Output Port 2. Output Port 2. Output Port 2. Output Port 2. Output Port 2. Output Port 13. LCD COMMON DUTY AND BIAS 1. 1/4 Duty, 1/3 Bias (when 4.5 V LCD is selected in Option 1) 2. 1/3 Duty, 1/3 Bias 3. 1/2 Duty, 1/3 Bias 1. 1/4 Duty, 1/2 Bias (when 3 V LCD is selected in Option 1) 2. 1/3 Duty, 1/2 Bias 3. 1/2 Duty, 1/2 Bias 14. SEGMENT MEMORY ADDRESS 1. 40H-6FH 4 2. C0H-EFH S1C60N09 ELECTRICAL CHARACTERISTICS Absolute Maximum Ratings S1C60N09 Rating Supply voltage Input voltage (1) Input voltage (2) Operating temperature Storage temperature Soldering temperature / time Symbol VSS VI VIOSC Topr Tstg Tsol Value -5.5 to 0.5 VSS - 0.3 to 0.5 VS1 - 0.3 to 0.5 -20 to 70 -65 to 150 260C, 10sec (lead section) (VDD=0V) Unit V V V C C - Symbol VSS VI VIOSC Topr Tstg Tsol Value -2.0 to 0.5 VSS - 0.3 to 0.5 VS1 - 0.3 to 0.5 -20 to 70 -65 to 150 260C, 10sec (lead section) (VDD=0V) Unit V V V C C - S1C60L09 Rating Supply voltage Input voltage (1) Input voltage (2) Operating temperature Storage temperature Soldering temperature / time Recommended Operating Conditions S1C60N09 Condition Supply voltage Oscillation frequency Symbol VSS fOSC Remark VDD=0V Crystal oscillation CR oscillation, RCR=475k Booster capacitor C1 Capacitor between VDD and VS1 C3 or C41 1: Depends on the LCD specification. Min. -3.6 0.1 0.1 S1C60L09 Condition Supply voltage Oscillation frequency Symbol VSS fOSC Remark VDD=0V Crystal oscillation CR oscillation, RCR=475k Booster capacitor C1 Capacitor between VDD and VS1 C3 or C41 1: Depends on the LCD specification. Min. -1.8 0.1 0.1 (Ta=-20 to 70C) Typ. Max. Unit -3.0 -2.6 V 32.768 kHz 65 80 kHz F F (Ta=-20 to 70C) Typ. Max. Unit -1.5 -1.2 V 32.768 kHz 65 80 kHz F F DC Characteristics S1C60N09(Unless otherwise specified: VDD=0V, VSS=-3.0V, fosc=32.768kHz, Ta=25C, VS1/VL1-VL3 are internal voltage, C1-C4=0.1F) Characteristic High level input voltage (1) High level input voltage (2) Low level input voltage (1) Low level input voltage (2) High level input current (1) High level input current (2) High level input current (3) Symbol VIH1 VIH2 VIL1 VIL2 IIH1 VIH1=0V, No pull-down IIH2 VIH2=0V, Pull-down IIH3 VIH3=0V, Pull-down Low level input current IIL VIL=VSS High level output current (1) High level output current (2) IOH1 IOH2 VOH1=0.1*VSS VOH2=0.1*VSS Low level output current (1) Low level output current (2) IOL1 IOL2 VOL1=0.9*VSS VOL2=0.9*VSS Common output current IOH3 IOL3 IOH4 IOL4 IOH5 IOL5 VOH3=-0.05V VOL3=VL3+0.05V VOH4=-0.05V VOL4=VL3+0.05V VOH5=0.1*VSS VOL5=0.9*VSS Segment output current (during LCD output) Segment output current (during DC output) Condition K00-03, P00-03, P10-13 RESET, TEST K00-03, P00-03, P10-13 RESET, TEST K00-03, P00-03, P10-13 K00-03 P00-03, P10-13 RESET, TEST K00-03, P00-03, P10-13 RESET, TEST R00, R03 R01, R02, P00-03, P10-13 R00, R03 R01, R02, P00-03, P10-13 COM0-3 Min. 0.2*VSS 0.1*VSS VSS VSS 0 4 50 -0.5 Typ. Max. 0 0 0.8*VSS 0.9*VSS 0.5 40 200 Unit V V V V A A A 0 A -1.8 -0.9 mA mA 4.0 3.0 mA mA -3 3 SEG0-37 -3 3 SEG0-37 -200 200 A A A A A A 5 S1C60N09 S1C60L09 (Unless otherwise specified: VDD=0V, VSS=-1.5V, fosc=32.768kHz, Ta=25C, VS1/VL1-VL3 are internal voltage, C1-C4=0.1F) Characteristic Max. Unit Condition Min. Typ. Symbol High level input voltage (1) 0 V K00-03, P00-03, P10-13 0.2*VSS VIH1 High level input voltage (2) 0 V VIH2 0.1*VSS RESET, TEST Low level input voltage (1) 0.8*VSS V VIL1 VSS K00-03, P00-03, P10-13 Low level input voltage (2) VIL2 VSS 0.9*VSS V RESET, TEST High level input current (1) A IIH1 VIH1=0V, No pull-down K00-03, P00-03, P10-13 0 0.5 High level input current (2) A IIH2 K00-03 VIH2=0V, Pull-down 2 16 High level input current (3) A VIH3=0V, Pull-down IIH3 P00-03, P10-13 25 100 RESET, TEST Low level input current A IIL K00-03, P00-03, P10-13 VIL=VSS -0.5 0 RESET, TEST IOH1 VOH1=0.1*VSS R00, R03 High level output current (1) A -300 High level output current (2) A IOH2 VOH2=0.1*VSS R01, R02, -150 P00-03, P10-13 Low level output current (1) A IOL1 VOL1=0.9*VSS R00, R03 1400 Low level output current (2) A IOL2 VOL2=0.9*VSS R01, R02, 700 P00-03, P10-13 Common output current A IOH3 VOH3=-0.05V COM0-3 -3 IOL3 VOL3=VL3+0.05V A 3 IOH4 VOH4=-0.05V SEG0-37 Segment output current A -3 (during LCD output) A IOL4 VOL4=VL3+0.05V 3 Segment output current A IOH5 VOH5=0.1*VSS SEG0-37 -100 (during DC output) A IOL5 VOL5=0.9*VSS 100 Analog Circuit Characteristics and Current Consumption S1C60N09 (Crystal Oscillation) * 4.5 V LCD panel, 1/4, 1/3, 1/2 duty, 1/3 bias (VL2 is shorted to VSS inside the IC) <Normal mode> (Unless otherwise specified: VDD=0V, VSS=-3.0V, fOSC=32.768kHz, Ta=25C, CG=25pF, VS1/VL1-VL3 are internal voltage, C1-C4=0.1F) Condition Typ. Min. Characteristic Max. Unit Symbol 1/2*VL2 LCD drive voltage 1/2*VL2 V VL1 Connect 1 M load resistor between VDD and VL1 (without panel load) - 0.1 x0.9 VSS VL2 Connect 1 M load resistor between VDD and VL2 V (without panel load) VL3 Connect 1 M load resistor between VDD and VL3 3/2*VL2 3/2*VL2 V (without panel load) - 0.1 x0.9 During HALT Without 2.5 IOP 1.0 Current consumption A During execution panel load 5.0 2.5 A <Heavy load protection mode> (Unless otherwise specified: VDD=0V, VSS=-3.0V, fOSC=32.768kHz, Ta=25C, CG=25pF, VS1/VL1-VL3 are internal voltage, C1-C4=0.1F) Characteristic Max. Unit Symbol Condition Typ. Min. LCD drive voltage 1/2*VL2 V VL1 Connect 1 M load resistor between VDD and VL1 1/2*VL2 (without panel load) - 0.1 x0.85 V VL2 Connect 1 M load resistor between VDD and VL2 VSS (without panel load) 3/2*VL2 3/2*VL2 V VL3 Connect 1 M load resistor between VDD and VL3 (without panel load) - 0.1 x0.85 Current consumption A Without 5.5 IOP During HALT 2.0 A During execution panel load 10.0 5.5 6 S1C60N09 * 3 V LCD panel, 1/4, 1/3, 1/2 duty, 1/2 bias (VL3 is shorted to VSS inside the IC and VL1 is shorted to VL2 outside the IC) <Normal mode> (Unless otherwise specified: VDD=0V, VSS=-3.0V, fOSC=32.768kHz, Ta=25C, CG=25pF, VS1/VL1-VL3 are internal voltage, C1-C3=0.1F) Min. Condition Typ. Characteristic Max. Unit Symbol 1/2*VL3 LCD drive voltage 1/2*VL3 V VL1 Connect 1 M load resistor between VDD and VL1 (without panel load) - 0.1 x0.9 VL2 Connect 1 M load resistor between VDD and VL2 1/2*VL3 1/2*VL3 V (without panel load) - 0.1 x0.9 VL3 Connect 1 M load resistor between VDD and VL3 VSS V (without panel load) During HALT Without IOP 1.0 2.5 Current consumption A During execution panel load 2.5 5.0 A <Heavy load protection mode> (Unless otherwise specified: VDD=0V, VSS=-3.0V, fOSC=32.768kHz, Ta=25C, CG=25pF, VS1/VL1-VL3 are internal voltage, C1-C3=0.1F) Min. Condition Typ. Characteristic Max. Unit Symbol 1/2*VL3 LCD drive voltage 1/2*VL3 V VL1 Connect 1 M load resistor between VDD and VL1 (without panel load) - 0.1 x0.85 VL2 Connect 1 M load resistor between VDD and VL2 1/2*VL3 1/2*VL3 V (without panel load) - 0.1 x0.85 VSS VL3 Connect 1 M load resistor between VDD and VL3 V (without panel load) During HALT Without IOP 2.0 5.5 Current consumption A During execution panel load 5.5 10.0 A S1C60L09 (Crystal Oscillation) * 4.5 V LCD panel, 1/4, 1/3, 1/2 duty, 1/3 bias (VL1 is shorted to VSS inside the IC) <Normal mode> (Unless otherwise specified: VDD=0V, VSS=-1.5V, fOSC=32.768kHz, Ta=25C, CG=25pF, VS1/VL1-VL3 are internal voltage, C1-C4=0.1F) Characteristic Max. Unit Symbol Condition Typ. Min. LCD drive voltage V VL1 Connect 1 M load resistor between VDD and VL1 VSS (without panel load) 2*VL1 V VL2 Connect 1 M load resistor between VDD and VL2 2*VL1 (without panel load) - 0.1 x0.9 V 3*VL1 3*VL1 VL3 Connect 1 M load resistor between VDD and VL3 (without panel load) - 0.1 x0.9 Current consumption A Without 2.5 IOP During HALT 1.0 A During execution panel load 5.0 2.5 <Heavy load protection mode> (Unless otherwise specified: VDD=0V, VSS=-1.5V, fOSC=32.768kHz, Ta=25C, CG=25pF, VS1/VL1-VL3 are internal voltage, C1-C4=0.1F) Characteristic Max. Unit Symbol Condition Typ. Min. LCD drive voltage V VL1 Connect 1 M load resistor between VDD and VL1 VSS (without panel load) 2*VL1 V VL2 Connect 1 M load resistor between VDD and VL2 2*VL1 (without panel load) - 0.1 x0.85 V 3*VL1 3*VL1 VL3 Connect 1 M load resistor between VDD and VL3 (without panel load) - 0.1 x0.85 Current consumption A During HALT Without 5.5 IOP 2.0 A During execution panel load 10.0 5.5 7 S1C60N09 * 3 V LCD panel, 1/4, 1/3, 1/2 duty, 1/2 bias (VL1 is shorted to VSS inside the IC and VL1 is shorted to VL2 outside the IC) <Normal mode> (Unless otherwise specified: VDD=0V, VSS=-1.5V, fOSC=32.768kHz, Ta=25C, CG=25pF, VS1/VL1-VL3 are internal voltage, C1-C3=0.1F) Min. Condition Typ. Characteristic Max. Unit Symbol VSS LCD drive voltage V VL1 Connect 1 M load resistor between VDD and VL1 (without panel load) VL2 Connect 1 M load resistor between VDD and VL2 VSS V (without panel load) 2*VL1 VL3 Connect 1 M load resistor between VDD and VL3 2*VL1 V (without panel load) - 0.1 x0.9 IOP 1.0 During HALT Without 2.5 Current consumption A 2.5 During execution panel load 5.0 A <Heavy load protection mode> (Unless otherwise specified: VDD=0V, VSS=-1.5V, fOSC=32.768kHz, Ta=25C, CG=25pF, VS1/VL1-VL3 are internal voltage, C1-C3=0.1F) Condition Typ. Min. Characteristic Max. Unit Symbol VSS LCD drive voltage V VL1 Connect 1 M load resistor between VDD and VL1 (without panel load) VL2 Connect 1 M load resistor between VDD and VL2 VSS V (without panel load) 2*VL1 VL3 Connect 1 M load resistor between VDD and VL3 2*VL1 V (without panel load) - 0.1 x0.85 During HALT Without 5.5 IOP 2.0 Current consumption A During execution panel load 10.0 5.5 A S1C60N09 (CR Oscillation) * 4.5 V LCD panel, 1/4, 1/3, 1/2 duty, 1/3 bias (VL2 is shorted to VSS inside the IC) <Normal mode> (Unless otherwise specified: VDD=0V, VSS=-3.0V, fOSC=65kHz, Ta=25C, VS1/VL1-VL3 are internal voltage, C1-C4=0.1F, RCR=475k) Characteristic Max. Unit Min. Condition Typ. Symbol LCD drive voltage 1/2*VL2 V 1/2*VL2 VL1 Connect 1 M load resistor between VDD and VL1 (without panel load) - 0.1 x0.9 V VL2 Connect 1 M load resistor between VDD and VL2 VSS (without panel load) 3/2*VL2 3/2*VL2 V VL3 Connect 1 M load resistor between VDD and VL3 (without panel load) - 0.1 x0.9 Current consumption A IOP 8.0 During HALT Without 15.0 A 15.0 During execution panel load 20.0 <Heavy load protection mode> (Unless otherwise specified: VDD=0V, VSS=-3.0V, fOSC=65kHz, Ta=25C, VS1/VL1-VL3 are internal voltage, C1-C4=0.1F, RCR=475k) Characteristic Max. Unit Condition Typ. Min. Symbol LCD drive voltage 1/2*VL2 V 1/2*VL2 VL1 Connect 1 M load resistor between VDD and VL1 (without panel load) - 0.1 x0.85 V VL2 Connect 1 M load resistor between VDD and VL2 VSS (without panel load) 3/2*VL2 3/2*VL2 V VL3 Connect 1 M load resistor between VDD and VL3 (without panel load) - 0.1 x0.85 Current consumption A During HALT Without 30.0 IOP 16.0 A During execution panel load 40.0 30.0 8 S1C60N09 * 3 V LCD panel, 1/4, 1/3, 1/2 duty, 1/2 bias (VL3 is shorted to VSS inside the IC and VL1 is shorted to VL2 outside the IC) <Normal mode> (Unless otherwise specified: VDD=0V, VSS=-3.0V, fOSC=65kHz, Ta=25C, VS1/VL1-VL3 are internal voltage, C1-C3=0.1F, RCR=475k) Characteristic Max. Unit Min. Condition Typ. Symbol LCD drive voltage 1/2*VL3 V 1/2*VL3 VL1 Connect 1 M load resistor between VDD and VL1 (without panel load) - 0.1 x0.9 1/2*VL3 1/2*VL3 V VL2 Connect 1 M load resistor between VDD and VL2 (without panel load) - 0.1 x0.9 V VL3 Connect 1 M load resistor between VDD and VL3 VSS (without panel load) Current consumption A IOP 8.0 During HALT Without 15.0 A 15.0 During execution panel load 20.0 <Heavy load protection mode> (Unless otherwise specified: VDD=0V, VSS=-3.0V, fOSC=65kHz, Ta=25C, VS1/VL1-VL3 are internal voltage, C1-C3=0.1F, RCR=475k) Characteristic Condition Typ. Max. Unit Min. Symbol LCD drive voltage 1/2*VL3 V 1/2*VL3 VL1 Connect 1 M load resistor between VDD and VL1 (without panel load) - 0.1 x0.85 VL2 Connect 1 M load resistor between VDD and VL2 1/2*VL3 1/2*VL3 V (without panel load) - 0.1 x0.85 VSS V VL3 Connect 1 M load resistor between VDD and VL3 (without panel load) Current consumption 30.0 A IOP 16.0 During HALT Without 40.0 A 30.0 During execution panel load S1C60L09 (CR Oscillation) * 4.5 V LCD panel, 1/4, 1/3, 1/2 duty, 1/3 bias (VL1 is shorted to VSS inside the IC) <Normal mode> (Unless otherwise specified: VDD=0V, VSS=-1.5V, fOSC=65kHz, Ta=25C, VS1/VL1-VL3 are internal voltage, C1-C4=0.1F, RCR=475k) Characteristic Max. Unit Min. Condition Typ. Symbol LCD drive voltage V VSS VL1 Connect 1 M load resistor between VDD and VL1 (without panel load) 2*VL1 V VL2 Connect 1 M load resistor between VDD and VL2 2*VL1 (without panel load) - 0.1 x0.9 3*VL1 3*VL1 V VL3 Connect 1 M load resistor between VDD and VL3 (without panel load) - 0.1 x0.9 Current consumption A IOP 8.0 During HALT Without 15.0 A 15.0 During execution panel load 20.0 <Heavy load protection mode> (Unless otherwise specified: VDD=0V, VSS=-1.5V, fOSC=65kHz, Ta=25C, VS1/VL1-VL3 are internal voltage, C1-C4=0.1F, RCR=475k) Characteristic Max. Unit Condition Typ. Min. Symbol LCD drive voltage V VSS VL1 Connect 1 M load resistor between VDD and VL1 (without panel load) 2*VL1 V VL2 Connect 1 M load resistor between VDD and VL2 2*VL1 (without panel load) - 0.1 x0.85 3*VL1 3*VL1 V VL3 Connect 1 M load resistor between VDD and VL3 (without panel load) - 0.1 x0.85 Current consumption A During HALT Without 30.0 IOP 16.0 A During execution panel load 40.0 30.0 9 S1C60N09 * 3 V LCD panel, 1/4, 1/3, 1/2 duty, 1/2 bias (VL1 is shorted to VSS inside the IC and VL1 is shorted to VL2 outside the IC) <Normal mode> (Unless otherwise specified: VDD=0V, VSS=-1.5V, fOSC=65kHz, Ta=25C, VS1/VL1-VL3 are internal voltage, C1-C3=0.1F, RCR=475k) Condition Typ. Characteristic Max. Unit Min. Symbol VSS LCD drive voltage V VL1 Connect 1 M load resistor between VDD and VL1 (without panel load) V VL2 Connect 1 M load resistor between VDD and VL2 VSS (without panel load) 2*VL1 V 2*VL1 VL3 Connect 1 M load resistor between VDD and VL3 (without panel load) - 0.1 x0.9 During HALT Without 15.0 Current consumption A IOP 8.0 During execution panel load 20.0 A 15.0 <Heavy load protection mode> (Unless otherwise specified: VDD=0V, VSS=-1.5V, fOSC=65kHz, Ta=25C, VS1/VL1-VL3 are internal voltage, C1-C3=0.1F, RCR=475k) Characteristic Max. Unit Min. Condition Typ. Symbol LCD drive voltage V VSS VL1 Connect 1 M load resistor between VDD and VL1 (without panel load) V VL2 Connect 1 M load resistor between VDD and VL2 VSS (without panel load) 2*VL1 V 2*VL1 VL3 Connect 1 M load resistor between VDD and VL3 (without panel load) - 0.1 x0.85 Current consumption A IOP 16.0 During HALT Without 30.0 A 30.0 During execution panel load 40.0 Oscillation Characteristics Oscillation characteristics will vary according to different conditions (elements used, boad pattern). Use the following characteristics are as reference values. S1C60N09 Crystal Oscillation (Unless otherwise specified: VDD=0V, VSS=-3.0V, fOSC=32.768kHz, Crystal: Q13MC146, CG=25pF, CD=built-in, Ta=25C) Characteristic Symbol Condition Min. Typ. Max. Unit Oscillation start voltage Vsta tsta5sec (VSS) -2.6 V Oscillation stop voltage Vstp tstp10sec (VSS) -2.6 V Including the parasitic capacitance inside the chip Built-in capacitance (drain) CD 20 pF f/V VSS=-2.6 to -3.6V Frequency/voltage deviation 5 ppm f/IC Frequency/IC deviation -10 10 ppm f/CG CG=5 to 25pF Frequency adjustment range 35 45 ppm (VSS) Harmonic oscillation start voltage Vhho -3.6 V Rleak Between OSC1 and VDD, VSS Permitted leak resistance 200 M S1C60L09 Crystal Oscillation (Unless otherwise specified: VDD=0V, VSS=-1.5V, fOSC=32.768kHz, Crystal: Q13MC146, CG=25pF, CD=built-in, Ta=25C) Characteristic Symbol Condition Min. Typ. Max. Unit Oscillation start voltage Vsta tsta5sec (VSS) -1.2 V Oscillation stop voltage Vstp tstp10sec (VSS) -1.2 V Including the parasitic capacitance inside the chip Built-in capacitance (drain) CD 20 pF f/V VSS=-1.2 to -1.8V Frequency/voltage deviation 5 ppm f/IC Frequency/IC deviation -10 10 ppm f/CG CG=5 to 25pF Frequency adjustment range 35 45 ppm (VSS) Harmonic oscillation start voltage Vhho -1.8 V Rleak Between OSC1 and VDD, VSS Permitted leak resistance 200 M S1C60N09 CR Oscillation Characteristic Symbol Oscillation frequency dispersion fOSC Oscillation start time tsta VSS=-2.6 to -3.6V (Unless otherwise specified: VDD=0V, VSS=-3.0V, RCR=475k, Ta=25C) Condition Min. Typ. Max. Unit 45.5 65 84.5 kHz 3 mS S1C60L09 CR Oscillation Characteristic Symbol Oscillation frequency dispersion fOSC Oscillation start time tsta VSS=-1.2 to -1.8V 10 (Unless otherwise specified: VDD=0V, VSS=-1.5V, RCR=475k, Ta=25C) Condition Min. Typ. Max. Unit 45.5 65 84.5 kHz 3 mS S1C60N09 BASIC EXTERNAL CONNECTION DIAGRAM Piezo Buzzer Single Terminal Driving I K00 K01 K02 K03 I/O P00 P01 P02 P03 P10 P11 P12 P13 COM3 SEG37 COM0 SEG0 LCD panel CB C1 CA VL1 VL2 VL3 VDD S1C60N09 S1C60L09 Capacitors (C2 and C3) are Connected. Connection depends on power supply and LCD panel specification. CGX OSC1 X'tal OSC2 VS1 C4 RESET R01 O R00 (BZ) R02 (FOUT) R03 (BZ) Lamp X'tal CGX C1 C2 C3 C4 CP Crystal oscillator Trimmer capacitor Capacitor Capacitor Capacitor Capacitor Capacitor TEST VSS + CP Piezo 32.768 kHz, CI = 35 k 5-25 pF 0.1 F 0.1 F 0.1 F 0.1 F 3.3 F Note: The above table is simply an example, and is not guaranteed to work. Piezo Buzzer Direct Driving R03 (BZ) R00 (BZ) S1C60N09/60L09 RA1 RA2 When driving the buzzer, set the IC into the heavy load protection mode since the supply voltage changes according to the buzzer frequency. Piezo RA1 Protection resistor 100 RA2 Protection resistor 100 11 S1C60N09 NOTICE: No part of this material may be reproduced or duplicated in any form or by any means without the written permission of Seiko Epson. Seiko Epson reserves the right to make changes to this material without notice. Seiko Epson does not assume any liability of any kind arising out of any inaccuracies contained in this material or due to its application or use in any product or circuit and, further, there is no representation that this material is applicable to products requiring high level reliability, such as, medical products. Moreover, no license to any intellectual property rights is granted by implication or otherwise, and there is no representation or warranty that anything made in accordance with this material will be free from any patent or copyright infringement of a third party. This material or portions thereof may contain technology or the subject relating to strategic products under the control of the Foreign Exchange and Foreign Trade Law of Japan and may require an export license from the Ministry of International Trade and Industry or other approval from another government agency. (c) Seiko Epson Corporation 2001 All right reserved. SEIKO EPSON CORPORATION ELECTRONIC DEVICES MARKETING DIVISION EPSON Electronic Devices Website http://www.epson.co.jp/device/ IC Marketing & Engineering Group ED International Marketing Department Europe & U.S.A. 421-8, Hino, Hino-shi, Tokyo 191-8501, JAPAN Phone : 042-587-5812 FAX : 042-587-5564 ED International Marketing Department Asia 421-8, Hino, Hino-shi, Tokyo 191-8501, JAPAN Phone : 042-587-5814 FAX : 042-587-5110 First issue February, 1999 M Printed July, 2001 in Japan L