LM48520 LM48520 Boosted Stereo Class D Audio Power Amplifier with Output Speaker Protection and Spread Spectrum Literature Number: SNAS367B LM48520 Boosted Stereo Class D Audio Power Amplifier with Output Speaker Protection and Spread Spectrum General Description Key Specifications The LM48520 integrates a boost converter with a high efficiency Class D stereo audio power amplifier to provide up to 1W/ch continuous power into an 8 speaker when operating from 2.7V to 5.0V power supply with boost voltage (PV1) of 5.0V. The LM48520 utilizes a proprietary spread spectrum pulse width modulation technique that lowers RF interference and EMI levels. The Class D amplifier is a low noise, filterless PWM architecture that eliminates the output filter, reducing external component count, board area, power consumption, system cost, and simplifying design. The LM48520 is designed for use in mobile phones and other portable communication devices. The high (78%) efficiency extends battery life when compared to Boosted Class AB amplifiers. The LM48520 features a low-power consumption shutdown mode. Shutdown may be enabled by driving the Shutdown pin to a logic low (GND). Also, external leakage is minimized via control of the ground reference via the SWOUT pin . The LM48520 has 4 gain options which are pin selectable via Gain0 and Gain1 pins. Output short circuit prevents the device from damage during fault conditions. Superior click and pop suppression eliminates audible transients during powerup and shutdown. Quiescent Power Supply Current 11.5mA (typ) Output Power (RL = 8, THD+N 1%, VDD = 3.3V,PV1 = 5.0V) Shutdown Current 1.1W (typ) 0.04A (typ) Features Click and Pop Suppression Low 0.04A Shutdown Current 78% Efficiency Filterless Class D 2.7V - 5.0V operation 4 Adjustable Gain settings Adjustable output swing limiter with Soft Clipping Speaker Protection Short circuit protection on Audio Amps Independent Boost and Amplifier shutdown pins Applications Mobile Phones PDAs Portable media Cameras Handheld games Boomer(R) is a registered trademark of National Semiconductor Corporation. (c) 2008 National Semiconductor Corporation 201987 www.national.com LM48520 Boosted Stereo Class D Audio Power Amplifier with Output Speaker Protection and Spread Spectrum March 20, 2008 LM48520 Typical Application 20198701 FIGURE 1. Typical LM48520 Audio Amplifier Application Circuit www.national.com 2 LM48520 Connection Diagrams LM48520TL 20198702 Top View Order Number LM48520TL See NS Package Number TLA25AAA Micro SMD Marking 20198721 Top View X -- Date Code T -- Die Traceability G -- Boomer Family I5 -- LM48520TL 3 www.national.com LM48520 Pin Descriptions Pin Designator Pin Name A1 VDD A2 BstFB Pin Function Power Supply Regulator Feedback Input. Connect BstFB to an external resistive voltage divider to set the boost output voltage. A3 Soft Start Soft start capacitor A4 SW_GND Booster ground A5 SW Drain of the Internal FET switch B1 INR+ Non-inverting right channel input B2 INR- Inverting right channel input B3 FB_GND Ground return for R1, R2 resistor divider B4 INL- Inverting left channel input B5 INL+ Non-inverting left channel input C1 V1 C2 BstSD C3 GND Ground C4 Gain0 Gain setting input 0 C5 PV1 D1 AmpSD Amplifier active low shutdown D2 OUTR+ Non-inverting right channel output D3 NC D4 OUTL+ Non-inverting left channel output D5 Gain1 Gain setting input 1 E1 VLimit Set to control output clipping level E2 OUTR- Inverting right channel output E3 PGND Power ground E4 OUTL- Inverting left channel output E5 NC www.national.com Amplifier supply voltage. Connect to PV1. Regulator active low shutdown Amplifier H-bridge power supply. Connect to V1. No connect No connect 4 JA (TL) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage (VDD, V1) Storage Temperature Input Voltage Power Dissipation (Note 3) ESD Susceptibility (Note 4) ESD Susceptibility (Note 5) Junction Temperature Operating Ratings Temperature Range 6V -65C to +150C -0.3V to VDD + 0.3V Internally limited 2000V 200V 150C Electrical Characteristics VDD = 3.3V 40.5 C/W TMIN TA TMAX -40C TA +85C 2.7V VDD 5.0V Supply Voltage (VDD) Amplifier Voltage (V1 ) 2.4V V1 5.5V Not under Boosted Condition Amplifier Voltage (PV1 ) 3.0V PV1 5.0V Under Boosted Condition (Notes 1, 2) The following specifications apply for VDD = 3.3V, AV = 6dB, RL = 15H + 8 +15H, fIN = 1kHz, unless otherwise specified. Limits apply for TA = 25C, R1 = 40.2k, R2 = 16.2k, V1 = PV1 = 5V, Vlimit = GND. All electrical specifications are for amplifier and booster. Symbol Parameter Conditions LM48520 Typical (Note 6) Limit (Notes 7, 8) Units (Limits) VIN = 0, RLOAD = IDD Quiescent Power Supply Current VDD = 2.7V 14.8 VDD = 3.3V 11.5 VDD = 5.0V 8.0 0.04 ISD Shutdown Current VSHUTDOWN = GND VSDIH Shutdown Voltage Input High For SD Boost, SD Amp VSDIL Shutdown Voltage Input Low For SD Boost, SD Amp TWU Wake-up Time Amplifier + Booster Wakeup VOS Output Offset Voltage G0, G1 = GND RL = G0 = VDD, G1 = GND AV Gain RL = G0 = GND, G1 = VDD RL = G0, G1 = VDD RL = PO Output Power 15.5 mA (max) 1.0 A (max) 1.4 V 0.4 V 3 ms 5 mV 6 dB 12 dB 18 dB 24 dB RL = 15H + 8 + 15H THD+N = 1% (max), f = 1kHz, 22kHz, BW VDD = 3.3V 1.1 RL = 15H + 8 + 15H THD+N = 10% (max), f = 1kHz, 22kHz, BW VDD = 3.3V 1.3 W 0.04 % 32 VRMS 0.87 W (min) PO = 500mW, f = 1kHz, THD+N Total Harmonic Distortion + Noise OS Output Noise RL = 15H + 8 + 15H, VDD = 3.3V VDD = 3.6V, f = 20Hz - 20kHz Inputs to AC GND, A weighted 5 www.national.com LM48520 Thermal Resistance Absolute Maximum Ratings (Note 2) LM48520 Symbol Parameter Conditions LM48520 Typical (Note 6) PSRR CMRR Power Supply Rejection Ratio Common Mode Rejection Ratio Limit (Notes 7, 8) Units (Limits) VRIPPLE = 200mVP-P Sine, fRIPPLE = = 217Hz 82 dB VRIPPLE = 200mVP-P Sine, fRIPPLE = = 1kHz 79 dB VRIPPLE = 1VP-P, fRIPPLE = 217Hz 67 dB 78 % 1.24 V PO = 1W, f = 1kHz, RL = 15H + 8 + 15H VDD = 3.3V VDD = 4.2V Efficiency VFB Feedback Pin Reference Voltage Vout clipped Output Voltage in clipped state with Vlimit = 2V, RL = 8, VIN = 2VP soft clip activated Vout clipped = 8/3 (PV1 - 2Vlimit) (Note 11) 2.5 1.9 3.2 Vpk (min) Vpk (max) Note 1: All voltages are measured with respect to the GND pin, unless otherwise specified. Note 2: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which guarantee specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not guaranteed for parameters where no limit is given, however, the typical value is a good indication of device performance. Note 3: The maximum power dissipation must be derated at elevated temperatures and is dictated by TJMAX, JA, and the ambient temperature, TA. The maximum allowable power dissipation is PDMAX = (TJMAX - TA) / JA or the given in Absolute Maximum Ratings, whichever is lower. Note 4: Human body model, 100pF discharged through a 1.5k resistor. Note 5: Machine Model, 220pF-240pF discharged through all pins. Note 6: Typicals are measured at 25C and represent the parametric norm. Note 7: Limits are guaranteed to National's AOQL (Average Outgoing Quality Level). Note 8: Datasheet min/max specification limits are guaranteed by design, test, or statistical analysis. Note 9: Shutdown current is measured in a normal room environment. The Shutdown pin should be driven as close as possible to Vin for minimum shutdown current. Note 10: Shutdown current is measured with components R1 and R2 removed. Note 11: Feedback pin reference voltage is measured with the Audio Amplifier disconnected from the Boost converter (the Boost converter is unloaded). www.national.com 6 LM48520 Typical Performance Characteristics THD+N vs Frequency VDD = 2.7V, POUT = 800mW, RL = 8 THD+N vs Frequency VDD = 3.3V, POUT = 900mW, RL = 8 20198703 20198704 THD+N vs Frequency VDD = 5.0V, POUT = 1W, RL = 8 THD+N vs Output Power VDD = 2.7V, RL = 8 20198706 20198705 THD+N vs Output Power VDD = 3.3V, RL = 8 THD+N vs Output Power VDD = 5.0V, RL = 8 20198707 20198708 7 www.national.com LM48520 Power Dissipation vs Output Power VDD = 2.7V, RL = 8, f = 1kHz Power Dissipation vs Output Power VDD = 3.3V, RL = 8, f = 1kHz 20198712 20198713 Power Dissipation vs Output Power VDD = 5.0V, RL = 8, f = 1kHz Efficiency vs Output Power VDD = 2.7V, RL = 8, f = 1kHz 20198709 20198714 Efficiency vs Output Power VDD = 3.3V, RL = 8, f = 1kHz Efficiency vs Output Power VDD = 5.0V, RL = 8, f = 1kHz 20198710 www.national.com 20198711 8 PSRR vs Frequency VDD =3.3V, VRIPPLE = 200mVP-P, RL = 8 20198722 20198723 Supply Current vs Supply Voltage No Load Output Power vs Supply Voltage RL = 8, f = 1kHz 20198724 20198725 Boost Output Voltage vs Load Current VDD = 2.7V Boost Output Voltage vs Load Current VDD = 3.3V 20198726 20198727 9 www.national.com LM48520 CMRR vs Frequency VDD =3.3V, VRIPPLE = 1VP-P, RL = 8 LM48520 Boost Output Voltage vs Load Current VDD = 5.0V 20198728 www.national.com 10 GENERAL AMPLIFIER FUNCTION The LM48520 features a Class D audio power amplifier that utilizes a filterless modulation scheme, reducing external component count, conserving board space and reducing system cost. The outputs of the device transition from PV1 to GND with a 300kHz switching frequency. With no signal applied, the outputs (VLS+ and VLS-) switch with a 50% duty cycle, in phase, causing the two outputs to cancel. This cancellation results in no net voltage across the speaker, thus there is no current to the load in the idle state. With the input signal applied, the duty cycle (pulse width) of the LM48520 outputs changes. For increasing output voltage, the duty cycle of VLS+ increases, while the duty cycle of VLSdecreases. For decreasing output voltages, the converse occurs. The difference between the two pulse widths yields the differential output voltage. VDD -- [VD + (IL x DCR)] Where VD is the forward voltage of the Schottky diode, IL is the current through the inductor, and DCR is the DC resistance of the inductor. Additionally, when the regulator is disabled, an external voltage between 2.4V and 5.5V can be applied directly to PV1 and V1 to power the amplifier. It is best to switch between ground and VDD for minimum current consumption while in shutdown. The LM48520 may be disabled with shutdown voltages in between GND and VDD, the idle current will be greater than the typical 0.1A value. Increased THD+N may also be observed when a voltage of less than VDD is applied to AmpSD. DIFFERENTIAL AMPLIFIER EXPLANATION The amplifier portion of the LM48520 is a fully differential amplifier that features differential input and output stages. A differential amplifier amplifies the difference between the two input signals. Traditional audio power amplifiers have typically offered only single-ended inputs resulting in a 6dB reduction in signal to noise ratio relative to differential inputs. The amplifier also offers the possibility of DC input coupling which eliminates the two external AC coupling, DC blocking capacitors. The amplifier can be used, however, as a single ended input amplifier while still retaining it's fully differential benefits. In fact, completely unrelated signals may be placed on the input pins. The amplifier portion of the LM48520 simply amplifies the difference between the signals. A major benefit of a differential amplifier is the improved common mode rejection ratio (CMRR) over single input amplifiers. The commonmode rejection characteristic of the differential amplifier reduces sensitivity to ground offset related noise injection, especially important in high noise applications. PROPER SELECTION OF EXTERNAL COMPONENTS Proper selection of external components in applications using integrated power amplifiers, and switching DC-DC converters, is critical for optimizing device and system performance. Consideration to component values must be used to maximize overall system quality. The best capacitors for use with the switching converter portion of the LM48520 are multi-layer ceramic capacitors. They have the lowest ESR (equivalent series resistance) and highest resonance frequency, which makes them optimum for high frequency switching converters. When selecting a ceramic capacitor, only X5R and X7R dielectric types should be used. Other types such as Z5U and Y5F have such severe loss of capacitance due to effects of temperature variation and applied voltage, they may provide as little as 20% of rated capacitance in many typical applications. Always consult capacitor manufacturer's data curves before selecting a capacitor. High-quality ceramic capacitors can be obtained from Taiyo-Yuden, AVX, and Murata. AMPLIFIER DISSIPATION AND EFFICIENCY The major benefit of a Class D amplifier is increased efficiency versus a Class AB. The efficiency of the LM48520 is attributed to the region of operation of the transistors in the output stage. The Class D output stage acts as current steering switches, consuming negligible amounts of power compared to their Class AB counterparts. Most of the power loss associated with the output stage is due to the IR loss of the MOSFET onresistance, along with switching losses due to gate charge. POWER SUPPLY BYPASSING FOR AMPLIFIER As with any amplifier, proper supply bypassing is critical for low noise performance and high power supply rejection. The capacitor location on both PV1, V1 and VDD pins should be as close to the device as possible. REGULATOR POWER DISSIPATION At higher duty cycles, the increased ON-time of the switch FET means the maximum output current will be determined by power dissipation within the LM48520 FET switch. The switch power dissipation from ON-time conduction is calculated by: PD(SWITCH) = DC x (IINDUCTOR(AVE))2 x RDS(ON) (W) (2) SELECTING INPUT CAPACITOR FOR AUDIO AMPLIFIER Input capacitors, CIN, in conjunction with the input impedance of the LM48520 forms a high pass filter that removes the DC bias from an incoming signal. The AC-coupling capacitor allows the amplifier to bias the signal to an optimal DC level. Assuming zero source impedance, the -3dB point of the high pass filter is given by: (1) Where DC is the duty cycle. f(-3dB) = 1/2RINCIN SHUTDOWN FUNCTION The LM48520 features independent amplifier and regulator shutdown controls, allowing each portion of the device to be disabled or enabled independently. AmpSD controls the (3) Choose CIN such that f-3dB is well below that lowest frequency of interest. Setting f-3dB too high affects the low-frequency responses of the amplifier. Use capacitors with low voltage 11 www.national.com LM48520 Class D amplifiers, while BstSD controls the regulator. Driving either inputs low disables the corresponding portion of the device, and reducing supply current. When the regulator is disabled, both FB_GND switches open, further reducing shutdown current by eliminating the current path to GND through the regulator feedback network. With the regulator disabled, there is still a current path from VDD, through the inductor and diode, to the amplifier power supply. This allows the amplifier to operate even when the regulator is disabled. The voltage at PV1 and V1 will be: Application Information LM48520 coefficient dielectrics, such as tantalum or aluminum electrolytic. Capacitors with high-voltage coefficients, such as ceramics, may result in increased distortion at low frequencies. Other factors to consider when designing the input filter include the constraints of the overall system. Although high fidelity audio requires a flat frequency response between 20Hz and 20kHz, portable devices such as cell phones may only concentrate on the frequency range of the frequency range of the spoken human voice (typically 300Hz to 4kHz). In addition, the physical size of the speakers used in such portable devices limits the low frequency response; in this case, frequencies below 150Hz may be filtered out. Cf = 1 / (2 X R1 X fz) SELECTING DIODES FOR BOOST The external diode used in Figure 1 should be a Schottky diode. A 20V diode such as the MBRS320T3 is recommended. The MBRS320T3 series of diodes are designed to handle a maximum average current of 3A. DUTY CYCLE The maximum duty cycle of the boost converter determines the maximum boost ratio of output-to-input voltage that the converter can attain in continuous mode of operation. The duty cycle for a given boost application is defined as: SELECTING OUTPUT CAPACITOR (CO) FOR BOOST CONVERTER A single 100F low ESR tantalum capacitor provides sufficient output capacitance for most applications. Higher capacitor values improve line regulation and transient response. Typical electrolytic capacitors are not suitable for switching converters that operate above 500kHz because of significant ringing and temperature rise due to self-heating from ripple current. An output capacitor with excessive ESR reduces phase margin and causes instability. Duty Cycle = VOUT + VDIODE - VIN / VOUT + VDIODE - VSW This applies for continuous mode operation. SELECTING INDUCTOR VALUE Inductor value involves trade-offs in performance. Larger inductors reduce inductor ripple current, which typically means less output voltage ripple (for a given size of output capacitor). Larger inductors also mean more load power can be delivered because the energy stored during each switching cycle is: SELECTING INPUT CAPACITOR (Cs1) FOR BOOST CONVERTER An input capacitor is required to serve as an energy reservoir for the current which must flow into the coil each time the switch turns ON. This capacitor must have extremely low ESR, so ceramic is the best choice. We recommend a nominal value of 2.2F, but larger values can be used. Since this capacitor reduces the amount of voltage ripple seen at the input pin, it also reduces the amount of EMI passed back along that line to other circuitry. E = L/2 X (IP)2 Where "lp" is the peak inductor current. The LM48520 will limit its switch current based on peak current. With IP fixed, increasing L will increase the maximum amount of power available to the load. Conversely, using too little inductance may limit the amount of load current which can be drawn from the output. Best performance is usually obtained when the converter is operated in "continuous" mode at the load current range of interest, typically giving better load regulation and less output ripple. Continuous operation is defined as not allowing the inductor current to drop to zero during the cycle. Boost converters shift over to discontinuous operation if the load is reduced far enough, but a larger inductor stays continuous over a wider load current range. During the TBDs ON-time, the inductor current ramps up TBDA and ramps down an equal amount during the OFFtime. This is defined as the inductor "ripple current". It can also be seen that if the load current drops to about TBDmA, the inductor current will begin touching the zero axis which means it will be in discontinuous mode. A similar analysis can be performed on any boost converter, to make sure the ripple current is reasonable and continuous operation will be maintained at the typical load current values. SELECTING SOFTSTART (CSS) CAPACITOR The soft-start function charges the boost converter reference voltage slowly. This allows the output of the boost converter to ramp up slowly thus limiting the transient current at startup. Selecting a soft-start capacitor (CSS) value presents a trade off between the wake-up time and the startup transient current. Using a larger capacitor value will increase wake-up time and decrease startup transient current while the apposite effect happens with a smaller capacitor value. A general guideline is to use a capacitor value 1000 times smaller than the output capacitance of the boost converter (CO). A 0.1uF softstart capacitor is recommended for a typical application. SETTING THE OUTPUT VOLTAGE (V1) OF BOOST CONVERTER The output voltage is set using the external resistors R1 and R2 (see Figure 1). A value of approximately 13.3k is recommended for R2 to establish a divider current of approximately 92A. R1 is calculated using the formula: R1 = R2 X (V1/1.23 - 1) (4) MAXIMUM SWITCH CURRENT The maximum FET switch current available before the current limiter cuts in is dependent on duty cycle of the application. This is illustrated in a graph in the typical performance characterization section which shows typical values of switch current as a function of effective (actual) duty cycle. FEED-FORWARD COMPENSATION FOR BOOST CONVERTER Although the LM48520's internal Boost converter is internally compensated, the external feed-forward capacitor Cf is required for stability (see Figure 1). Adding this capacitor puts a zero in the loop response of the converter. The recommended frequency for the zero fz should be approximately 6kHz. Cf1 can be calculated using the formula: www.national.com (5) CALCULATING OUTPUT CURRENT OF BOOST CONVERTER (IAMP) As shown in Figure 2 which depicts inductor current, the load current is related to the average inductor current by the relation: 12 tor, make certain that the continuous current rating is high enough to avoid saturation at peak currents, where: (6) IIND = (PV1 / VDD) x ILOAD(BOOST) Where "DC" is the duty cycle of the application. The switch current can be found by: ISW = IIND(AVG) + 1/2 (IRIPPLE) A suitable core type must be used to minimize core (switching) losses, and wire power losses must be considered when selecting the current rating. (7) PCB Layout Guidelines Inductor ripple current is dependent on inductance, duty cycle, input voltage and frequency: IRIPPLE = DC x (VIN-VSW) / (f x L) High frequency boost converters require very careful layout of components in order to get stable operation and low noise. All components must be as close as possible to the LM48520 device. It is recommended that a four layer PCB be used so that internal ground planes are available. Some additional guidelines to be observed (all designators are referencing Figure 1): 1. Keep the path between L1, D1, and Co extremely short. Parasitic trace inductance in series with D1 and Co will increase noise and ringing. 2. The feedback components R1, R2 and Cf1 must be kept close to the FB pin to prevent noise injection on the FB pin trace. 3. Since the external components of the boost converter are switching, L1 and D1 should be kept away from the input traces to prevent the noise from injecting into the input. 4. The power supply bypass capacitors, Cs1 and Cs2 should be placed as close to the LM48520 device as possible. (8) combining all terms, we can develop an expression which allows the maximum available load current to be calculated: ILOAD(max) = (1-DC)x(ISW(max)-DC(VIN-VSW))/fL (10) (9) The equation shown to calculate maximum load current takes into account the losses in the inductor or turn-OFF switching losses of the FET and diode. DESIGN PARAMETERS VSW AND ISW The value of the FET "ON" voltage (referred to as VSW in equations 4 thru 7) is dependent on load current. A good approximation can be obtained by multiplying the "ON Resistance" of the FET times the average inductor current. FET on resistance increases at VIN values below 5V, since the internal N-FET has less gate voltage in this input voltage range (see Typical Performance Characteristics curves). Above VIN = 5V, the FET gate voltage is internally clamped to 5V. The maximum peak switch current the device can deliver is dependent on duty cycle. For higher duty cycles, see Typical Performance Characteristics curves. GROUNDING GUIDELINES There are three grounds on the LM48520, GND, SW_GND, and PGND. When laying out the PCB, it is critical to connect the grounds as close to the device as possible. The simplest way to do that is to place vias close to the GND, SW_GND, and PGND bumps and connect the GND, SW_GND, and PGND vias using a single ground plane in an inner layer of the PCB. INDUCTOR SUPPLIERS The recommended inductor for the LM48520 is the NR8040T6R8N from Taiyo Yuden. When selecting an induc- 13 www.national.com LM48520 ILOAD = IIND(AVG) x (1 - DC) LM48520 Output Speaker Protection Function The LM48520's output voltage limiter can be used to set a minimum and maximum output voltage swing magnitude. The voltage applied to the VLimit pin controls the limit on the output voltage level. The output level is determined by the following equation: Vout clipped = 8/3 * (PV1 -- 2 * Vlimit) or Vout clipped = 1/2 * (PV1 -- 3/8 * Vout clipped) Where, Vout clipped = the desired output level measured in Vpk, PV1 = Boost output voltage, and Vlimit is the voltage applied the the Vlimit pin on the LM48520. To disable the limiter, set Vlimit = 0V. Figure 2 provides an example of how the output voltage limiter functions with VDD = 3.3V, AV = 6dB, PV1 = 5V, Vlimit = 2V, RL = 8, VIN = 2VP. www.national.com 20198729 FIGURE 2. Soft Clipping vs No Clipping 14 LM48520 Revision History Rev Date 1.0 02/27/08 Initial release. Description 1.01 03/07/08 Added the Soft clipping vs No clipping curve. 1.02 03/12/08 Text edits. 15 www.national.com LM48520 Physical Dimensions inches (millimeters) unless otherwise noted micro SMD Package Order Number LM48520TL NS Package Number TLA25AAA X1 = 2.49mm, X2 = 2.49mm, X3 = 0.6mm, www.national.com 16 LM48520 Notes 17 www.national.com LM48520 Boosted Stereo Class D Audio Power Amplifier with Output Speaker Protection and Spread Spectrum Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: Products Design Support Amplifiers www.national.com/amplifiers WEBENCH www.national.com/webench Audio www.national.com/audio Analog University www.national.com/AU Clock Conditioners www.national.com/timing App Notes www.national.com/appnotes Data Converters www.national.com/adc Distributors www.national.com/contacts Displays www.national.com/displays Green Compliance www.national.com/quality/green Ethernet www.national.com/ethernet Packaging www.national.com/packaging Interface www.national.com/interface Quality and Reliability www.national.com/quality LVDS www.national.com/lvds Reference Designs www.national.com/refdesigns Power Management www.national.com/power Feedback www.national.com/feedback Switching Regulators www.national.com/switchers LDOs www.national.com/ldo LED Lighting www.national.com/led PowerWise www.national.com/powerwise Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors Wireless (PLL/VCO) www.national.com/wireless THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION ("NATIONAL") PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL'S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright(c) 2008 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: europe.support@nsc.com German Tel: +49 (0) 180 5010 771 English Tel: +44 (0) 870 850 4288 National Semiconductor Asia Pacific Technical Support Center Email: ap.support@nsc.com National Semiconductor Japan Technical Support Center Email: jpn.feedback@nsc.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated