56F8300
16-bit Digital Signal Controllers
freescale.com
56F8345/56F8145
Data Sheet
Preliminary Technical Data
MC56F8345
Rev. 17
01/2007
56F8345 Technical Data, Rev. 17
2 Freescale Semiconductor
Preliminary
Document Revision History
Version History Description of Change
Rev 1.0 Pre-Release version, Alpha customers only
Rev 2.0 Initial Public Release
Rev 3.0 Corrected typo in Table 10-4, Flash Endurance is 10,000 cycles. Addressed additio nal
grammar issues.
Rev 4.0 Added “Typical Min” values to Table 10-16. Edited grammar, spelling, consistency of
language throughout family. Updated va lues in Current Consumption per Power Supply Pin,
Table 10-7, Regulator Parameters, Table 10-9, External Clo ck Operation Timing
Requirements Table 10-13, SPI Timing, Table 10-17, ADC Parameters, Table 10-23, and IO
Loading Coefficients at 10MHz, Table 10-24.
Rev 5.0 Added Part 4.8. Added the word “access” to FM Error Interrupt in Table 4-5. Removed min
and max numbers. Clarified CSBAR 0 and CSBAR 1 reset values in Table 4-10. Removed
min and max numbers, only documenting Typ. numbers for LVI in Table 10-6.
Rev 6.0 Updated numbers in Table 10-7 and Table 10-8 with more recent data. Corrected typo in
Table 10-3 in Pd characteristics.
Rev 7.0 Replaced any reference to Flash Interfa ce Unit with Flash Memory Module. Added note to
VCAP pin in Table ?-??????. Removed unneccessary notes in Table 10-12. Corrected
temperature range in Table 10-14. Added ADC calibration information to Table 10-23 and
new graphs in Figure 10-21.
Rev 8.0 Clarified Table 10-22. Corrected Digital Input Current Low (pull-up enabled) numbers in
Table 10-5. Removed text and Table 10-2. Replaced with note to Table 10-1.
Rev 9.0 Added 56F8145 information; edited to indicate differences in 56F8345 and 56F8145.
Reformatted for Freescale look and feel. Updated Temper ature Sensor and ADC tables;
updated balance of electrical tables for consistency throughout fa mily. Clarified I/O power
description in Table ?-??????, added note to Table 10-7 and clarified Section 12.3.
Rev 10.0 Corrected beginning address for On-Chip Data RAM, Table 4-6.
Rev 11.0 Corrected addresses in Table 4-6.
Rev 12.0 Corrected Figure 10-21. Added output voltage maximum value and note to clarify in
Table 10-1; also removed overall life expectancy note, since life expectancy is dependent on
customer usage and must be determined by reliability engineering. Clarifie d value and unit
measure for Maximum allowed PD in Table 10-3. Corrected note about average value for
Flash Data Retention in Table 10-4. Added new RoHS-compliant orderable part numbers in
Table 13-1.
Rev 13.0 Updated Table 10-23 to reflect new value for maximum Uncalibrated Gain Erro r
Rev 14.0 Deleted RSTO from Pin Group 2 (listed after Table 10-1). Deleted fo rmula for Max Ambient
Operating Temperature (Automotive) and Max Ambient Operating Temperature (Industrial) in
Table 10-4. Added RoHS-compliance and “pb-free” language to back cover.
Please see http://www.freescale.com for the most current Data Sheet revision.
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 3
Preliminary
Rev 15.0 Updated JTAG ID in Section 6.5.4. Added information/corrected state during reset in
Table 2-2. Clarified external reference crystal frequency for PLL in Table 10-14 by increasing
maximum value to 8.4MHz.
Rev 16.0 Replaced “Tri-stated” with an explanation in State During Reset column in Table 2-2.
Rev. 17 • Added the following note to the description of the TMS signal in Table 2-2:
Note: Always tie the TMS pin to VDD through a 2.2K resistor.
• Added the following note to the description of the TRST signal in Table 2-2:
Note: For normal operation, connect TRST directly to VSS. If the design is to be used in a
debugging environment, TRST may be tied to VSS through a 1K resistor.
Document Revision History (Continued)
Version History Description of Change
Please see http://www.freescale.com for the most current data sheet revision.
56F8345 Technical Data, Rev. 17
4 Freescale Semiconductor
Preliminary
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 5
Preliminary
56F8345/56F8145 Block Diagram - 128 LQFP
Quadrature
Decoder 1 or
Quad
Timer B or
SP1I or
GPIOC
Program Controller
and Hardware
Looping Unit
Data ALU
16 x 16 + 36 -->36-Bit MAC
Three 16-bit Input Registers
Four 36-bit Accumulators
Address
Generation Unit Bit
Manipulation
Unit
16-Bit
56800E Core
Interrupt
Controller
COP/
Watchdog
SCI1 or
GPIOD
42IRQA IRQB
PDB
PDB
XAB1
XAB2
XDB2
CDBR
SCI0 or
GPIOE
SPI0 or
GPIOE
IPBus Bridge (IPBB)
Decoding
Peripherals
Peripheral
Device Selects RW
Control IPAB IPWDB IPRDB
2
System Bus
R/W Control
PAB
PAB
CDBW
CDBR
CDBW
JTAG/
EOnCE
Port
Digital Reg Analog Reg
Low Voltage
Supervisor
VCAP VDD VSS VDDA VSSA
547 52
VPP
2
RESET
RSTO
4
6
3
4
6
3
Quad Ti me r
D or GPIOE
Quad Timer
C or GPIOE
ADCA
4
5
Quadrature
Decoder 0 or
Quad
Timer A or
GPIOC
FlexCAN
2
4
2
ADCB
4
4
VREF
TEMP_SENSE
4
* External
Address Bus
Switch
External Bus
Interface Unit
* External
Data
Bus Switch
A8-13 or GPIOA0-5
D7-10 or GPIOF0-3
GPIOB0-4 or A16-20
GPIOD0-5 or CS2-7
* Bus
Control
6
5
4
6
* EMI not functional in
this package; use as
GPIO pi ns
PLL
Clock
Generator XTAL
EXTAL
CLKMODE
Integration
Module
System
P
O
RO
S
C
Clock
resets
CLKO
PWM Outputs
Fault Inputs
PWMA
Current Sense Inputs
or GPIOC
PWM Outputs
Fault Inputs
PWMB
Current Sense Inputs
or GPIOD
OCR_DIS
4AD1
AD0
4
AD1
AD0
Data Memory
4K x 16 Flash
4K x 16 RAM
Memory
Program Memory
64K x 16 Flash
2K x 16 RAM
4K x 16 Boot
Flash Control
56F8345/56F8145 General Description
Note: Features in italics are NOT available in the 56F8145 device.
• Up to 60 MIPS at 60MHz core frequency
• DSP and MCU functionality in a unified,
C-efficient architecture
• 128KB Program Flash
• 4KB Program RAM
• 8KB Data Flash
• 8KB Data RAM
• 8KB Boot Flash
• Up to two 6-channel PWM modules
• Four 4-channel, 12-bit ADCs
• Temperature Sensor
•Up to two Quadrature Decoders
• FlexCAN module
• Optional On-Chip Regulator
• Two Serial Communication Interfaces (SCIs)
• Up to two Serial Peripheral Interface (SPIs)
• Up to four general-purpose Quad Ti mers
• Computer Operating Properly (COP)/Watc hdog
• JTAG/Enhanced On-Chip Emulation (OnCE™) for
unobtrusive, real-time debugging
• Up to 49 GPIO lines
• 128-pin LQFP Package
56F8345 Technical Data, Rev. 17
6 Freescale Semiconductor
Preliminary
Part 1 Overview . . . . . . . . . . . . . . . . . . . . . . . .7
1.1 56F8345/56F8145 Features . . . . . . . . . . . .7
1.2 Device Description. . . . . . . . . . . . . . . . . . . .9
1.3 Award-Winning Development Enviro nment11
1.4 Architecture Block Diagram. . . . . . . . . . . .12
1.5 Product Documentation. . . . . . . . . . . . . . .16
1.6 Data Sheet Conventions . . . . . . . . . . . . . .16
Part 2 Signal/Connection Descriptions . . . .17
2.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . .17
2.2 Signal Pins. . . . . . . . . . . . . . . . . . . . . . . . .20
Part 3 On-Chip Clock Synthesis (OCCS). . .36
3.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . .36
3.2 External Clock Operation. . . . . . . . . . . . . .36
3.3 Registers . . . . . . . . . . . . . . . . . . . . . . . . . .38
Part 4 Memory Map . . . . . . . . . . . . . . . . . . . .38
4.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . .38
4.2 Program Map. . . . . . . . . . . . . . . . . . . . . . .39
4.3 Interrupt Vector Table . . . . . . . . . . . . . . . .41
4.4 Data Map. . . . . . . . . . . . . . . . . . . . . . . . . .45
4.5 Flash Memory Map . . . . . . . . . . . . . . . . . .4 5
4.6 EOnCE Memory Map. . . . . . . . . . . . . . . . .46
4.7 Peripheral Memory Mapped Registers . . .47
4.8 Factory Programmed Memory. . . . . . . . . .73
Part 5 Interrupt Controller (ITCN). . . . . . . . .74
5.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . .74
5.2 Features. . . . . . . . . . . . . . . . . . . . . . . . . . .74
5.3 Functional Description. . . . . . . . . . . . . . . .74
5.4 Block Diagram . . . . . . . . . . . . . . . . . . . . . .76
5.5 Operating Modes. . . . . . . . . . . . . . . . . . . .76
5.6 Register Descriptions . . . . . . . . . . . . . . . . .77
5.7 Resets . . . . . . . . . . . . . . . . . . . . . . . . . . .103
Part 6 System Integration Module (SIM) . .104
6.1 Introduction . . . . . . . . . . . . . . . . . . . . . . .104
6.2 Features. . . . . . . . . . . . . . . . . . . . . . . . . .104
6.3 Operating Modes. . . . . . . . . . . . . . . . . . .105
6.4 Operating Mode Register. . . . . . . . . . . . .105
6.5 Register Descriptions. . . . . . . . . . . . . . . .106
6.6 Clock Generation Overview. . . . . . . . . . .119
6.7 Power-Down Modes Overview . . . . . . . .119
6.8 Stop and Wait Mode Disable Func tion . .120
6.9 Resets . . . . . . . . . . . . . . . . . . . . . . . . . . .121
Part 7 Security Features . . . . . . . . . . . . . . .121
7.1 Operation with Security Enabled . . . . . . .121
7.2 Flash Access Blocking Mechanisms . . . .122
Part 8 General Purpose Input/Output
(GPIO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
8.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . 1 25
8.2 Memory Maps . . . . . . . . . . . . . . . . . . . . . 125
8.3 Configuration. . . . . . . . . . . . . . . . . . . . . . 125
Part 9 Joint Test Action Group (JTAG) . . 131
9.1 JTAG Information . . . . . . . . . . . . . . . . . .131
Part 10 Specifications . . . . . . . . . . . . . . . . 131
10.1 General Characteristics. . . . . . . . . . . . . .131
10.2 DC Electrical Characteristics . . . . . . . . . . 136
10.3 AC Electrical Characteristics. . . . . . . . . .140
10.4 Flash Memory Characteristics. . . . . . . . . 140
10.5 External Clock Operation Timing . . . . . . 141
10.6 Phase Locked Loop Timing. . . . . . . . . . . 141
10.7 Crystal Oscillator Timing . . . . . . . . . . . . .142
10.8 Reset, Stop, Wait, Mode Select, and
Interrupt Timing . . . . . . . . . . . . . . .142
10.9 Serial Peripheral Interface (SPI)
Timing. . . . . . . . . . . . . . . . . . . . . . . 144
10.10 Quad Timer Timing . . . . . . . . . . . . . . . . .148
10.11 Quadrature Decoder Timing . . . . . . . . . .148
10.12 Serial Communication Interface (SCI)
Timing. . . . . . . . . . . . . . . . . . . . . . . 149
10.13 Controller Area Network (CAN) Timing. . 150
10.14 JTAG Timing . . . . . . . . . . . . . . . . . . . . . . 1 50
10.15 Analog-to-Digital Converter (ADC)
Parameters. . . . . . . . . . . . . . . . . . . 152
10.16 Equivalent Circuit for ADC Inputs . . . . . . 155
10.17 Power Consumption . . . . . . . . . . . . . . . . 156
Part 11 Packaging . . . . . . . . . . . . . . . . . . . 158
11.1 56F8345 Package and Pin-Out
Information . . . . . . . . . . . . . . . . . . . 158
11.2 56F8145 Package and Pin-Out
Information . . . . . . . . . . . . . . . . . . . 161
Part 12 Design Considerations. . . . . . . . . 167
12.1 Thermal Design Considerations . . . . . . . 1 67
12.2 Electrical Design Considerations . . . . . .168
12.3 Power Distribution and I/O Ring
Implementation. . . . . . . . . . . . . . . .169
Part 13 Ordering Information . . . . . . . . . . 170
Table of Contents
56F8345/56F8145 Features
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 7
Preliminary
Part 1 Overview
1.1 56F8345/56F8145 Features
1.1.1 Core
• Efficient 16-bit 56800E family controller engine with dual Harvard architecture
• Up to 60 Million Instructions Per Second (MIPS) at 60MHz core frequency
• Single-cycle 16 × 16-bit parallel Multiplier -Accumulator (MAC)
• Four 36-bit accumulators, including extension bits
• Arithmetic and logic multi-bit shifter
• Parallel instruction set with unique DSP addressing modes
• Hardware DO and REP loops
• Three internal address buses
• Four internal data buses
• Instruction set supports both DSP and controller functions
• Controller-style addressing modes and instructions for compact code
• Efficient C compiler and local variable support
• Software subroutine and interrupt stack with depth limited only by memory
• JTAG/EOnCE debug programming interface
1.1.2 Differences Between Devices
Table 1-1 outlines the key differences between the 56F8345 and 56F8145 devices.
Table 1-1 Device Differences
Feature 56F8345 56F8145
Guaranteed Speed 60MHz/60 MIPS 40MHz/40MIPS
Program RAM 4KB Not Available
Data Flash 8KB Not Available
PWM 2 x 6 1 x 6
CAN 1 Not Available
Quad Timer 4 2
Quadrature Decode r 2 x 4 1 x 4
Temperature Sensor 1 Not Available
56F8345 Technical Data, Rev. 17
8 Freescale Semiconductor
Preliminary
1.1.3 Memory
Note: Features in italics are NOT available in the 56F8145 device.
• Harvard architecture permits as many as three simultaneous accesses to program and data memory
• Flash security protection feature
• On-chip memory, including a low-cost, high-volume Flash solution
— 128KB of Program Flash
— 4KB of Program RAM
— 8KB of Data Flash
—8KB of Data RAM
— 8KB of Boot Flash
• EEPROM emulation capability
1.1.4 Peripheral Circuits
Note: Features in italics are NOT available in the 56F8145 device.
• Pulse Width Modulato r module:
— In the 56F83 45, two Pulse W idth Modu lator modules, each with six P WM outputs, three Current Sen se
inputs, and four Fault inputs; fault-tolerant design with dead time insertion; supports both center-aligned
and edge-aligned modes
— In the 56F8145, one Pul se W idth Modulator module with six PWM outputs, three Current Sense inputs
and three Fault inputs; fault-tolerant design with dead time insertion; supports both center-aligned and
edge-aligned modes
• Four 12-bit, Analog-to-Digital Co nv erters (ADCs), which support four simultaneous conversions with
quad, 4-pin multiplexed inputs; ADC and PWM modules can be synchr onized through Timer C, channels
2 and 3
• Quadrature Deco der:
— In the 56F8345, two four-input Quadrature Decoders or two additional Quad Timers
— In the 56F8145, one four-input Quadrature Decoder, which works in conjunction with Quad Timer A
•Temperature Sensor can be connected, on the board, to any of the ADC inputs to monitor the on-chip
temperature
•Quad Timer:
— In the 56F8345, four dedicated general-purpose Quad T imers totaling six dedicated pins: Timer C with
two pins and Timer D with four pins
— In the 56F8145, two Quad Timers; Timer A and Timer C both work in conjunction with GPIO
• Optional On-Chip Regulator
• FlexCAN (CAN Version 2.0 B-compliant) module with 2-pin port for transmit and receive
• Two Serial Communication Interfaces (SCIs), each with two pins (or four additional GPIO lines)
• Up to two Serial Peripheral Interfaces (SPIs), both with configurable 4-pin port (or eight additional GPIO
lines); SPI 1 can also be used as Quadrature Decoder 1 or Quad Timer B
• Computer Operating Properly (COP)/Watchdog timer
Device Description
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 9
Preliminary
• Two dedicated external interrupt pins
• 49 General Purpose I/O (GPIO) pins; 28 pins dedicated to GPIO
• External reset input pin for hardware reset
• External reset output pin for system reset
• Integrated low-voltage interrupt module
• JTAG/ Enhanced On-Chip Emulation (OnCE) for unobtrusive, processor speed-independent, real-time
debugging
• Software-programmable, Phase Lock Loop-based frequency synthesizer for the core clock
1.1.5 Energy Information
• Fabricated in high-density CMOS with 5V-tolerant, TTL-compatible digital inputs
• On-board 3.3V down to 2.6V voltage regulator for powering internal logic and memories; can be disabled
• On-chip regulators for digital and analog circuitry to lower cost and reduce noise
• Wait and Stop modes available
• ADC smart power management
• Each peripheral can be individually disabled to save power
1.2 Device Description
The 56F8345 and 56F8145 are members of the 56800E core-based family of controllers. Each combines,
on a single chip, the processing power of a Digital Signal Processor (DSP) and the functionality of a
microcontroller with a flexible set of peripherals to create an extremely cost-effective solution. Because
of their low cost, configuration flexibility, and compact program code, the 56F8345 and 56F8145 are
well-suited for many applications. The devices include many peripherals that are especially useful for
motion control, smart appliances, steppers, encoders, tachometers, limit switches, power supply and
control, automotive control (56F8345 only), engine management, noise suppression, remote utility
metering, industrial control for power, lighting, and automation applications.
The 56800E core is based on a Harvard-style architecture consisting of three execution units operating in
parallel, allowing as many as six operations per instruction cycle. The MCU-style programming model and
optimized instruction set allow straightforward generation of efficient, compact DSP and control code.
The instruction set is also highly efficient for C/C++ Compilers to enable rapid development of optimized
control applications.
The 56F8345 and 56F8145 support program execution from internal memories. Two data operands can be
accessed from the on-chip data RAM per instruction cycle. These devices also provide two external
dedicated interrupt lines and up to 49 General Purpose Input/Output (GPIO) lines, depending on peripheral
configuration.
1.2.1 56F8345 Features
The 56F8345 controller includes 128KB of Program Flash and 8KB of Data Flash (each programmable
through the JTAG port) with 4KB of Program RAM and 8KB of Data RAM. A total of 8KB of Boot Flash
is incorporated for easy customer inclusion of field-programmable software routines that can be used to
56F8345 Technical Data, Rev. 17
10 Freescale Semiconductor
Preliminary
program the main Program and Data Flash memory areas. Both Program and Data Flash memories can be
independently bulk erased or erased in pages. Program Flash page erase size is 1KB. Boot and Data Flash
page erase size is 512 bytes. The Boot Flash memory can also be either bulk or page erased.
A key application-specific feature of the 56F8345 is the inclusion of two Pulse Width Modulator (PWM)
modules. These modules each incorporate three complementary, individually programmable PWM signal
output pairs (each module is also capable of supporting six independent PWM functions, for a total of 12
PWM outputs) to enhance motor control functionality. Complementary operation permits programmable
dead time insertion, distortion correction via current sensing by software, and separate top and bottom
output polarity control. The up-counter value is programmable to support a continuously variable PWM
frequency. Edge-aligned and center-aligned synchronous pulse width control (0% to 100% modulation) is
supported. The device is capable of controlling most motor types: ACIM (AC Induction Motors); both
BDC and BLDC (Brush and Brushless DC motors); SRM and VR M (Switched and Variable Reluctance
Motors); and stepper motors. The PWMs incorporate fault protection and cycle-by-cycle current limiting
with sufficient output drive capability to directly drive standard optoisolators. A “smoke-inhibit”,
write-once protection feature for key parameters is also included. A patented PWM waveform distortion
correction circuit is also provided. Each PWM is double-buffered and includes interrupt controls to permit
integral reload rates to be programmable from 1 to 16. The PWM modules provide reference outputs to
synchronize the Analog-to-Digital Converters through two channels of Quad Timer C.
The 56F8345 incorporates two Quadrature Decoders capable of capturing all four transitions on the
two-phase inputs, permitting generation of a number proportional to actual position. Speed computation
capabilities accommodate both fast- and slow-moving shafts. An integrated watchdog timer in the
Quadrature Decoder can be programmed with a time-out value to alert when no shaft motion is detected.
Each input is filtered to ensure only true transitions are recorded.
This controller also provides a full set of standard programmable peripherals that include two Serial
Communications Interfaces (SCIs); two Serial Peripheral Interfaces (SPIs); and four Quad Timers. Any of
these interfaces can be used as General Purpose Input/Outputs (GPIOs) if that function is not required. A
Flex Controller Area Network (FlexCAN) interface (CAN Version 2.0 B-compliant) and an internal
interrupt controller are also a part of the 56F8345.
1.2.2 56F8145 Features
The 56F8145 controller includes 128KB of Program Flash, programmable through the JTAG port, and
8KB of Data RAM. A total of 8KB of Boot Flash is incorporated for easy customer inclusion of
field-programmable software routines that can be used to program the main Program Flash memory area.
The Program Flash memory can be independently bulk erased or erased in pages; Program Flash page
erase size is 1KB. The Boot Flash page erase size is 512 bytes; Boot Flash memory can also be either bulk
or page erased.
A key application-specific feature of the 56F8145 is the inclusion of one Pulse Width Modulator (PWM)
module. This module incorporates three complementary, individually programmable PWM signal output
pairs and can also support six independent PWM functions to enhance motor control functionality.
Complementary operation permits programmable dead time insertion, distortion correction via current
sensing by software, and separate top and bottom output polarity control. The up-counter value is
programmable to support a continuously variable PWM frequency. Edge-aligned and center-aligned
Award-Winning Development Environment
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 11
Preliminary
synchronous pulse width control (0% to 100% modulation) is supported. The device is capable of
controlling most motor types: ACIM (AC Induction Motors); both BDC and BLDC (Brush and Brushless
DC motors); SRM and VRM (Switched and Variable Reluctance Motors); and stepper motors. The PWM
incorporates fault protection and cycle-by-cycle current limiting with sufficient output drive capability to
directly drive standard optoisolators. A “smoke-inhibit”, write-once protection feature for key parameters
is also included. A patented PWM waveform distortion correction circuit is also provided. The PWM is
double-buffered and includes interrupt controls to permit integral reload rates to be programmable from 1
to 16. The PWM module provides reference outputs to synchronize the Analog-to-Digital Converters
through two channels of Quad Timer C.
The 56F8145 incorporates a Quadrature Decoder capable of capturing all four transitions on the two-phase
inputs, permitting generation of a number proportional to actual position. Speed computation capabilities
accommodate both fast- and slow-moving shafts. An integrated watchdog timer in the Quadrature Decoder
can be programmed with a time-out value to alert when no shaft motion is detected. Each input is filtered
to ensure only true transitions are recorded.
This controller also provides a full set of standard programmable peripherals that include two Serial
Communications Interfaces (SCI s); two Seria l Peripheral Interfaces (SPIs); and two Quad Timers. Any of
these interfaces can be used as General Purpose Input/Outputs (GPIOs) if that function is not required. An
internal interrupt controller is also a part of the 56F8145.
1.3 Award-Winning Development Environment
Processor ExpertTM (PE) provides a Rapid Application Design (RAD) tool that combines easy-to-use
component-based software application creation with an expert knowledge system.
The CodeWarrior Integrated Development Environment is a sophisticated tool for code navigation,
compiling, and debugging. A complete set of evaluation modules (EVMs) and development system cards
will support concurrent engineering. Together, PE, CodeWarrior and EVMs create a complete, scalable
tools solution for easy, fast, and efficient development.
56F8345 Technical Data, Rev. 17
12 Freescale Semiconductor
Preliminary
1.4 Architecture Block Diagram
Note: Features in italics are NOT available in the 56F8145 device and are shaded in the following figures.
The 56F8345/56F8145 architecture is shown in Figure 1-1 and Figure 1-2. Figure 1-1 illustrates how the
56800E system buses communicate with internal memories and the IPBus Bridge. Table 1-2 lists the
internal buses in the 56800E architecture and provides a brief description of their function. Figure 1-2
shows the peripherals and control blocks connected to the IPBus Bridge. The figures do not show the
on-board regulator and power and ground signals. They also do not show the multiplexing between
peripherals or the dedicated GPIOs. Please see Part 2, Signal/Connection Descriptions, to see which
signals are multiplexed with those of other peripherals.
Also shown in Figure 1-2 are connections between the PWM, Timer C and ADC blocks. These
connections allow the PWM and/or Timer C to control the timing of the start of ADC conversions. The
Timer C channel indicated can generate periodic start (SYNC) signals to the ADC to start its conversions.
In another operating mode, the PWM load interrupt (SYNC output) signal is routed internally to the Timer
C input channel as indicated. The timer can then be used to introduce a controllable delay before
generating its output signal. The timer output then triggers the ADC. To fully understand this interaction,
please see the 56F8300 Peripheral User’s Manual for clarification on the operation of all three of these
peripherals.
Architecture Block Diagram
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 13
Preliminary
Figure 1-1 System Bus Interfaces
Note: Flash memories are encapsulated within the Flash Memory (FM) Module. Flash control is
accomplished by the I/O to the FM over the peripheral bus, while reads and writes are completed
between the core and the Flash memories.
Note: The primary data RAM port is 32 bits wide. Other data ports are 16 bits.
56800E
Program
Flash
Program
RAM
Data RAM
EMI*
Data
Flash
IPBus
Bridge
Boot
Flash
Flash
Memory
Module
* EMI not functional in this package; since only part of
the address/data bus is bonded out, use as GPIO pins
NOT available on the 56F8145 device.
JTAG / EOnCE
5
11
pdb_m[15:0]
4
pab[20:0]
cdbw[31:0]
xab2[23:0]
xab1[23:0]
cdbr_m[31:0]
xdb2_m[15:0
6
Address
Data
Control
CHIP
TAP
Controller
TAP
Linking
Module
External
JTAG Port
To Flash
Control
Logic
IPBus
56F8345 Technical Data, Rev. 17
14 Freescale Semiconductor
Preliminary
Figure 1-2 Peripheral Subsystem
Timer A
Timer C
Timer D
SPI1
ADCB
ADCA
FlexCAN
GPIOA
SPI0
SCI0
SCI1
Interrupt
Controller
To/From IPBus Bridge
PWMA
PWMB
Quadrature Decoder 0
Note: ADC A and ADC B use the same
voltage reference circuit with VREFH,
VREFP, VREFMID, VREFN, and VREFLO
pins.
GPIOB
GPIOC
GPIOD
GPIOE
GPIOF
Timer B
Quadrature Decoder 1
TEMP_SENSE
NOT available on the 56F8145 device.
Low-Voltage Interrupt
System POR
COP Reset
RESET
POR & LVI
SIM
COP
2
13
13
CLKGEN
(OSC / PLL)
4
4
4
SYNC Output
SYNC Output
2
ch3i ch2i
ch3o ch2o
8
8
1
2
2
4
IPBus
Architecture Block Diagram
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 15
Preliminary
Table 1-2 Bus Signal Names
Name Function
Program Memory Interface
pdb_m[15:0] Program data bus for instruction word fetches or read operatio ns.
cdbw[15:0] Primary core data bus use d for program memory writes. (Only these 16 bits of the cdbw[31:0] bus
are used for writes to program memory.)
pab[20:0] Program memory address bus. Data is returned on pdb_m bus.
Primary Data Memory Interfac e Bus
cdbr_m[31:0] Primary core data bus for memory reads. Add re ssed via xab1 bus.
cdbw[31:0] Primary core data bus for memory writes. Addressed via xab1 bus.
xab1[23:0] Primary data address bus. Capable of addressing bytes1, words, and long data types. Data is written
on cdbw and returned on cdbr_m. Also used to access memory-mapped I/O.
1. Byte accesses can only occur in t he bottom half of the memory address space. The MSB of the address will be forced
to 0.
Secondary Data Memory Interface
xdb2_m[15:0] Secondary data bu s used for secondary data address bus xab2 in the dual memory reads.
xab2[23:0] Secondary data ad dress bus used for the second of two simultaneous accesses. Capable of
addressing only words. Data is returned on xdb2_m.
Peripheral Interface Bus
IPBus [15:0] Peripheral bus accesses all on-chip peripherals registers. This bus operates at the same clock rate
as the Primary Data Memory and therefore generates no delays when accessing the processor.
Write data is obtained from cdbw. Read data is provided to cdbr_m.
56F8345 Technical Data, Rev. 17
16 Freescale Semiconductor
Preliminary
1.5 Product Documentation
The documents listed in Table 1-3 are required for a complete description and proper design with the
56F8345 and 56F8145 devices. Documentation is available from local
Freescale
distributors,
Freescale
Semiconductor sales offices,
Freescale
Literature Distribution Centers, or online at
http://www.freescale.com.
1.6 Data Sheet Conventions
This data sheet uses the following conventions:
Table 1-3 Chip Documentation
Topic Description Order Number
DSP56800E
Reference Manual Detailed description of the 56800E family architecture,
16-bit controller core processor, and the instruction set DSP56800EERM
56F8300 Peripheral User
Manual Detailed description of perip herals of the 56F8300
family of devices MC56F8300UM
56F8300 SCI/CAN
Bootloader User Manual Detailed description of th e SCI/CAN Bootloaders
56F8300 family of devices MC56F83xxBLUM
56F8345/56F8145
Technical Data Sheet Electrical and timing specifications, pin descriptions,
device specific peripheral information and package
descriptions (this document)
MC56F8345
Errata Details any chip issues that might be present MC56F8345E
MC56F8145E
OVERBAR This is used to indicate a signal that is active when pulled low. For example, the RESET pin is
active when low.
“asserted” A high true (active high) signal is high or a low true (active low) signal is low.
“deasserted” A high true (active high) signal is low or a low true (active low) signal is high.
Examples: Signal/Symbol Logic State Signal State Voltage1
1. Values for VIL, VOL, VIH, and VOH are defined by individual product specifications.
PIN True Asserted VIL/VOL
PIN False Deasserted VIH/VOH
PIN True Asserted VIH/VOH
PIN False Deasserted VIL/VOL
Introduction
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 17
Preliminary
Part 2 Signal/Connection Descriptions
2.1 Introduction
The input and output signals of the 56F8345 and 56F8145 are organized into functional groups, as detailed
in Table 2-1 and as illustrated in Figure 2-1. In Table 2-2, each table row describes the signal or signals
present on a pin.
Table 2-1 Functional Group Pin Allocations
Functional Grou p Number of Pins in Package
56F8345 56F8145
Power (VDD or VDDA)99
Power Option Control 11
Ground (VSS or VSSA)66
Supply Capacitors1 & VPP
1. If the on-chip regulator is disabled, the VCAP pins ser ve as 2. 5V VDD_CORE power inputs
66
PLL and Clock 44
Bus Control 66
Interrupt and Program Control 44
Pulse Width Modulator (PWM) Ports 26 13
Serial Peripheral Interface (SPI) Port 0 44
Serial Peripheral Interface (SPI) Port 1 —4
Quadrature Decoder Port 02
2. Alternately, can f unction as Quad Timer pins or GPIO
44
Quadrature Decoder Port 13
3. Pins in this section can function as Quad Timer, SPI 1, orGPIO
4—
Serial Communications Interface (SCI) Ports 44
CAN Ports 2—
Analog-to-Digital Converter (ADC) Ports 21 21
Timer Module Ports 64
JTAG/Enhanced On-Chip Emulati on (EOnCE) 55
Temperature Sense 1—
Dedicated GPIO ( Address Bus = 11; Data Bus = 44)
4. EMI not functional in these packages; use as GPIO pins.
Note: See Table 1-1 for 56F8145 functional differences.
28 28
56F8345 Technical Data, Rev. 17
18 Freescale Semiconductor
Preliminary
Figure 2-1 56F8345 Signals Identified by Functional Group1 (128-Pin LQFP)
1. Alternate pin functionality is shown in parenthesis; pin direction/type shown is the default functionality.
VDD_IO
VDDA_OSC_PLL
VSS
VSSA_ADC
Other
Supply
Ports
PLL
and
Clock
*External
Address
Bus
or GPIO
*External
Data Bus
*External
Bus
Control
SCI0 or
GPIOE
SCI1 or
GPIO
JTAG/
EOnCE
Port
5
1
7
1
1
VCAP1 - VCAP4
VPP1 & VPP24
2
Power
Power
Power
Ground
Ground
1
1
1
A8 - A13 (GPIOA0 - 5)
D7 - D10 (GPIOF0 - 3)
GPIOD0 - 5 (CS2 - 7)
TXD1 (GPIOD6)
RXD1 (GPIOD7)
Quadrature
Decoder 0
or Quad
Timer A or
GPIO
PHASEB0(TA1, GPIOC5 )
INDEX0 (TA2, GPIOC6)
HOME0 (TA3, GPIOC7)
ISA0 - 2 (GPIOC8 - 10)
FAULTB0-3
PWMB0 - 5
ANA0 - 7
TD0 - 3 (GPIOE10 - 13)
IRQA
IRQB
RESET
RSTO
SPI0 or
GPIO
Quadrature
Decoder 1 or
Quad Timer B
or SPI1 or
GPIO
Temperature
Sensor
6
5
4
1
1
1
1
1
1
1
1
1
6
3
3
8
5
4
GPIOB0-4 (A16 - 20)
6
EXTAL
XTAL
CLKO
1
7
1
1
1
1
TXD0 (GPIOE0)
RXD0 (GPIOE1)
TCK
TMS
TDI
TDO
TRST
SCLK0 (GPIOE4)
MOSI0 (GPIOE5)
MISO0 (GPIOE6)
SS0 (GPIOE7)
PHASEB1 (TB1, MOSI1, GPIOC1)
INDEX1 (TB2, MISO1, GPIOC2)
HOME1 (TB3, SS1, GPIOC3)
PWMA0 - 5
FAULTA0 - 3
ISB0 - 2 (GPIOD10 - 12)
ANB0 - 7
CAN_RX
CAN_TX
TC0 - 1 (GPIOE8 - 9)
PWMA
PWMB
ADCB
ADCA
CAN
Interrupt/
Program
Control
PHASEA1(TB0, SCLK1, GPIOC0)
6
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
6
4
8
1
1
2
1
1
1
1
VREF
CLKMODE 1
TEMP_SENSE
1
* EMI not functional in this package; use as GPIO pins
OCR_DIS
VDDA_ADC
156F8345
PHASEA0 (TA0, GPIOC4)
Quad
Timer C
and D or
GPIO
Introduction
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 19
Preliminary
Figure 2-2 56F8145 Signals Identified by Functional Group1 (128-Pin LQFP)
1. Alternate pin functionality is shown in parenthesis; pin direction/type shown is the default functionality.
VDD_IO
VDDA_OSC_PLL
VSS
VSSA_ADC
Other
Supply
Ports
PLL
and
Clock
*External
Address
Bus
or GPIO
*External
Data Bus
*External
Bus
Control
SCI0 or
GPIOE
SCI1 or
GPIO
JTAG/
EOnCE
Port
5
1
7
1
1
VCAP1 - VCAP4
VPP1 & VPP24
2
Power
Power
Power
Ground
Ground
1
1
1
A8 - A13 (GPIOA0 - 5)
D7 - D10 (GPIOF0 - 3)
GPIOD0 - 5 (CS2 - 7)
TXD1 (GPIOD6)
RXD1 (GPIOD7)
Quadrature
Decoder 0
or Quad
Timer A or
GPIO
PHASEB0(TA1, GPIOC5 )
INDEX0 (TA2, GPIOC6)
HOME0 (TA3, GPIOC7)
(GPIOC8 - 10)
FAULTB0-3
PWMB0 - 5
ANA0 - 7
(GPIOE10 - 13)
IRQA
IRQB
RESET
RSTO
SPI0 or
GPIO
SPI1 or
GPIO
6
5
4
1
1
1
1
1
1
1
1
1
3
3
8
5
4
GPIOB0-4 (A16 - 20)
6
EXTAL
XTAL
CLKO
1
7
1
1
1
1
TXD0 (GPIOE0)
RXD0 (GPIOE1)
TCK
TMS
TDI
TDO
TRST
SCLK0 (GPIOE4)
MOSI0 (GPIOE5)
MISO0 (GPIOE6)
SS0 (GPIO E7)
(MOSI1, GPIOC1)
(MISO1, GPIOC2)
(SS1,GPIOC3)
ISB0 - 2 (GPIOD10 - 12)
ANB0 - 7
TC0 - 1 (GPIOE8 - 9)
GPIO
PWMB
ADCB
ADCA
Interrupt/
Program
Control
(SCLK1, GPIOC0)
6
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
6
4
8
2
1
1
1
1
VREF
CLKMODE 1
* EMI not functional in this package; use as GPIO pins
OCR_DIS
VDDA_ADC
156F8145
PHASEA0 (TA0, GPIOC4)
QUAD
Timer C or
GPIO
56F8345 Technical Data, Rev. 17
20 Freescale Semiconductor
Preliminary
2.2 Signal Pins
After reset, each pin is configured for its primary function (listed first). Any alternate functionality must
be programmed.
EMI is not functional in this package; since only part of the address/data bus is bonded out, use as GPIO
pins.
Note: Signals in italics are NOT available in the 56F8145 device.
If the “State During Reset” lists more than one state fo r a pin, the first state is the actual reset state. Other
states show the reset condition of the alternate function, which you get if the alternate pin function is
selected without changing the configuration of the alternate peripheral. For example, the A8/GPIOA0 pin
shows that it is tri-stated during reset. If the GPIOA_PER is changed to select the GPIO function of the
pin, it will become an input if no other registers are changed.
Table 2-2 Signal and Package Information fo r the 128-Pin LQFP
Signal
Name Pin No. Type State
During
Reset Signal Description
VDD_IO 4 Supply I/O Power — This pin supplies 3.3V power to the chip I/O
interface and also the Processor core throught the on-chip
voltage regulator, if it is enabled.
VDD_IO 14
VDD_IO 25
VDD_IO 36
VDD_IO 62
VDD_IO 76
VDD_IO 112
VDDA_ADC 94 Supply ADC Power — This pin supplies 3. 3V po w er to the ADC
modules. It must be connected to a clean analo g power supply.
VDDA_OSC_
PLL 72 Supply Oscillator and PLL Power — This pin supplies 3.3V power to
the OSC and to the internal regulator that in turn supplies the
Phase Locked Loop. It must be connected to a clean analog
power supply.
VSS 3 Supply Ground — These pins provide groun d for chip logic and I/O
drivers.
VSS 21
VSS 35
VSS 59
VSS 65
Signal Pins
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 21
Preliminary
VSSA_ADC 95 Supply ADC Analog Ground — This pin supplies an analog ground to
the ADC modul e s.
OCR_DIS 71 Input Input On-Chip Regul ator Disable —
Tie this pin to VSS to enable the on-chip regulator
Tie this pin to VDD to disable the on-chip regulator
This pin is intended to be a static DC signal from powe r-up
to shut down. Do not try to toggle this pin for p ower savings
during operation.
VCAP149 Supply Supply VCAP1 - 4 — When OCR_DIS is tied to VSS (regulator enabled),
connect each pin to a 2.2μF or greater bypa ss capacito r in order
to bypass the core logic voltage regulator, required for proper
chip operation. When OCR_DIS is tied to VDD (regulator
disabled), these pins become VDD_CORE and should be
connected to a regulated 2.5V power supply.
Note: This bypass is required even if the chip is powered
with an external supply.
VCAP2122
VCAP375
VCAP413
VPP1119 Input Input VPP1 - 2 — These pins should be left unconnected as an open
circuit for normal functionality.
VPP25
CLKMODE 79 Input Input Clock Input Mode Selection — This input determines the
function of the XTAL and EXTAL pins.
1 = External clock input on XTAL is used to directly drive the
input clock of the chip. The EXTAL pin should be grounded.
0 = A crystal or ceramic resonator should be connected between
XTAL and EXTAL.
EXTAL 74 Input Input External Crystal Oscillator Input — This input ca n be
connected to an 8MHz external crystal. Tie this pin low if XTAL is
driven by an external clock source.
XTAL 73 Input/
Output Chip-driven Crystal Oscillator Output — This output connects the internal
crystal oscillator output to an external crystal.
If an external clock is used, XTAL must be used as the input and
EXTAL connected to GND.
The input clock can be selected to provide th e clock directly to
the core. This input clock can also be selected as the input clock
for the on-chip PLL.
Table 2-2 Signal and Package Information fo r the 128-Pin LQFP
Signal
Name Pin No. Type State
During
Reset Signal Description
56F8345 Technical Data, Rev. 17
22 Freescale Semiconductor
Preliminary
CLKO 6 Output In reset,
output is
disabled
Clock Output — This pin outputs a buffered clock signal. Using
the SIM CLKO Select Register (SIM_CLKOSR), this pin can be
programmed as any of the following: disabled, CLK_MSTR
(system clock), IPBus clock, oscillator output, prescaler clock
and postscaler clock. Other signals are al so available for test
purposes.
See Part 6.5.7 for details.
A8
(GPIOA0)
15 Output
Schmitt
Input/
Output
In reset,
output is
disabled,
pull-up is
enabled
Address Bus — A8 - A13 specify six of the address lines for
external program or data memory accesses. Depending upon
the state of the DRV bit in the EMI bus control register (BCR), A8
- A13 and EMI control signals are tri-stated when th e external
bus is inactive.
Port A GPIO — These six GPIO pins can be individually
programmed as input or output pins.
After reset, these pins default to address bus functionality and
must be programme d as GPIO.
To deactivate the internal pull-up resistor, clear the appropriate
GPIO bit in the GPIOA_PUR register.
Example: GPIOA0, clear bit 0 in the GPIOA_PUR register.
Note: Primary function is not available in this package
configuration; GPIO function must be used instead.
A9
(GPIOA1) 16
A10
(GPIOA2) 17
A11
(GPIOA3) 18
A12
(GPIOA4) 19
A13
(GPIOA5) 20
GPIOB0
(A16)
27 Schmitt
Input/
Output
Output
Input,
pull-up
enabled
Port B GPIO — These four GPIO pins can be individually
programmed as an input or output pin.
Address Bus — A16 - A19 specify four of the address lines for
external program or data memory accesses. Depending upon
the state of the DRV bit in the EMI bus control register (BCR),
A16 - A19 and EMI control signals are tri-stated when the
external bus is inactive.
After reset, the default state is GPIO.
To deactivate the internal pull-up resistor, clear bit 0 in the
GPIOB_PUR register.
Example: GPIOB1, clear bit 1 in the GPIOB_PUR register.
GPIOB1
(A17)
28
GPIOB2
(A18)
29
GPIOB3
(A19)
30
Table 2-2 Signal and Package Information fo r the 128-Pin LQFP
Signal
Name Pin No. Type State
During
Reset Signal Description
Signal Pins
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 23
Preliminary
GPIOB4
(A20)
(prescaler_
clock)
31 Schmitt
Input/
Output
Output
Output
Input,
pull-up
enabled
Port B GPIO — This GPIO pin can be individually programmed
as an input or output pin.
Address Bus — A20 specifies one of the address lines for
external program or data memory accesses. Depending upon
the state of the DRV bit in the EMI bus control register (BCR),
A20 and EMI control signals are tri-stated when the external bus
is inactive.
Clock Output — can be used to monitor the prescaler_clock on
GPIOB4.
After reset, the default state is GPIO.
This pin can also be used to view the prescaler_clock. In these
cases, the GPIOB_PER can be used to disable the GPIO. The
CLKOSR register in the SIM can then be used to choose
between address and clock functions; see
Part 6.5.7 for details.
To deactivate the internal pull-up resistor, clear bit 4 in the
GPIOB_PUR register.
D7
(GPIOF0)
22 Input/
Output
Input/
Output
In reset,
output is
disabled,
pull-up is
enabled
Data Bus — D7 - D10 specify part of the data for external
program or data memory accesses. Depending upon the state of
the DRV bit in the EMI bus control register (BCR), D7 - D10 are
tri-stated when the external bus is inac tive
Port F GPIO — These four GPIO pins can be individually
programmed as input or output pins.
After reset, these pins default to data bus functionality and
should be programmed as GPIO.
To deactivate the internal pull-up resistor, clear the appropriate
GPIO bit in the GPIOF_PUR register.
Example: GPIOF0, clear bit 0 in the GPIOF_PUR register.
Note: Primary function is not available in this package
configuration; GPIO function must be used instead.
D8
(GPIOF1) 23
D9
(GPIOF2) 24
D10
(GPIOF3) 26
Table 2-2 Signal and Package Information fo r the 128-Pin LQFP
Signal
Name Pin No. Type State
During
Reset Signal Description
56F8345 Technical Data, Rev. 17
24 Freescale Semiconductor
Preliminary
GPIOD0
(CS2)
42 Input/
Output
Output
Input,
pull-up
enabled
Port D GPIO — These six GPIO pins can be individually
programmed as input or output pins.
Chip Select — CS2 - CS7 may be programmed within the EMI
module to act as chip selects for specific areas of the external
memory map. Depending upon the state of the DRV bit in the
EMI bus control register (BCR), CS2 - CS7 are tri-stated when
the external bus is inactive.
After reset, these pins are configured as GPIO.
To deactivate the internal pull-up resistor, clear the appropriate
GPIO bit in the GPIOD_PUR register.
Example: GPIOD0, clear bit 0 in the GPIOD_PUR register.
GPIOD1
(CS3)43
GPIOD2
(CS4)44
GPIOD3
(CS5)45
GPIOD4
(CS6) 46
GPIOD5
(CS7) 47
TXD0
(GPIOE0)
7 Output
Input/
Output
In reset,
output is
disabled,
pull-up is
enabled
Transmit Data — SCI0 transmit data output
Port E GPIO — This GPIO pin can be individually programmed
as an input or output pin.
After reset, the default state is SCI output.
To deactivate the internal pull-up resistor, clear bit 0 in the
GPIOE_PUR register.
RXD0
(GPIOE1)
8 Input
Input/
Output
Input,
pull-up
enabled
Receive Data — SCI0 receive data input
Port E GPIO — This GPIO pin can be individually programmed
as an input or output pin.
After reset, the default state is SCI output.
To deactivate the internal pull-up resistor, clear bit 1 in the
GPIOE_PUR register.
TXD1
(GPIOD6)
40 Output
Input/
Output
In reset,
output is
disabled,
pull-up is
enabled
Transmit Data — SCI1 transmit data output
Port D GPIO — This GPIO pin can be individually programmed
as an input or output pin.
After reset, the default state is SCI output.
To deactivate the internal pull-up resistor, clear bit 6 in the
GPIOD_PUR register.
Table 2-2 Signal and Package Information fo r the 128-Pin LQFP
Signal
Name Pin No. Type State
During
Reset Signal Description
Signal Pins
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 25
Preliminary
RXD1
(GPIOD7)
41 Input
Input/
Output
Input,
pull-up
enabled
Receive Data — SCI1 receive data input
Port D GPIO — This GPIO pin can be individually programmed
as an input or output pin.
After reset, the default state is SCI input.
To deactivate the internal pull-up resistor, clear bit 7 in the
GPIOD_PUR register.
TCK 115 Schmitt
Input Input,
pulled low
internally
Test Clock Input — This input pin provides a gated clock to
synchronize the test logic and shift serial data to the
JTAG/EOnCE port. The pin is connected internally to a
pull-down resistor.
TMS 116 Schmitt
Input Input,
pulled high
internally
Test Mode Select Input — This input pin is used to sequence
the JTAG TAP controller’s state machine. It is sampled on the
rising edge of TCK and has an on-chip pull-up resistor.
To deactivate the internal pull-up resistor, set the JTAG bit in the
SIM_PUDR register.
Note: Always tie the TMS pin to VDD through a 2.2K resistor.
TDI 117 Schmitt
Input Input,
pulled high
internally
Test Data Input — This input pin provides a serial input data
stream to the JTAG/EOn CE port. It is sampled on the rising edge
of TCK and has an on-chip pull-up resistor.
To deactivate the internal pull-up resistor, set the JTAG bit in the
SIM_PUDR register.
TDO 118 Output In reset,
output is
disabled,
pull-up is
enabled
Test Data Output — This tri-stateable output pin provides a
serial output data stream from the JTAG/EOnCE port. It is driven
in the shift-IR and shift-DR controller states, and changes on the
falling edge of TCK.
Table 2-2 Signal and Package Information fo r the 128-Pin LQFP
Signal
Name Pin No. Type State
During
Reset Signal Description
56F8345 Technical Data, Rev. 17
26 Freescale Semiconductor
Preliminary
TRST 114 Schmitt
Input Input,
pulled high
internally
Test Reset — As an input, a low signal on this pin provides a
reset signal to the JTAG TAP controller. To ens ure complete
hardware reset, TRST should be asserted whenever RESET is
asserted. The only exception occurs in a debugging environment
when a hardware device reset is required and the JTAG/EOnCE
module must not be reset. In this case, assert RESET, but do not
assert TRST.
To deactivate the internal pull-up resistor, set the JTAG bit in the
SIM_PUDR register.
Note: For normal operation, connect TRST directly to VSS. If the
design is to be used in a debugging environment, TRST may be tied to
VSS through a 1K resistor.
PHASEA0
(TA0)
(GPIOC4)
127 Schmitt
Input
Schmitt
Input/
Output
Schmitt
Input/
Output
Input,
pull-up
enabled
Phase A — Quadrature Decoder 0, PHASEA input
TA0 — Timer A, Channel 0
Port C GPIO — This GPIO pin can be individually programmed
as an input or output pin.
After reset, the default state is PHASEA0.
To deactivate the internal pull-up resistor, clear bit 4 of the
GPIOC_PUR register.
PHASEB0
(TA1)
(GPIOC5)
128 Schmitt
Input
Schmitt
Input/
Output
Schmitt
Input/
Output
Input,
pull-up
enabled
Phase B — Quadrature Decoder 0, PHASEB input
TA1 — Timer A, Channel 1
Port C GPIO — This GPIO pin can be individually programmed
as an input or output pin.
After reset, the default state is PHASEB0.
To deactivate the internal pull-up resistor, clear bit 5 of the
GPIOC_PUR register.
Table 2-2 Signal and Package Information fo r the 128-Pin LQFP
Signal
Name Pin No. Type State
During
Reset Signal Description
Signal Pins
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 27
Preliminary
INDEX0
(TA2)
(GPIOC6)
1Schmitt
Input
Schmitt
Input/
Output
Schmitt
Input/
Output
Input,
pull-up
enabled
Index — Quadrature Decoder 0, INDEX input
TA2 — Timer A, Channel 2
Port C GPIO — This GPIO pin can be individually programmed
as an input or output pin.
After reset, the default state is INDEX0.
To deactivate the internal pull-up resistor, clear bit 6 of the
GPIOC_PUR register.
HOME0
(TA3)
(GPIOC7)
2Schmitt
Input
Schmitt
Input/
Output
Schmitt
Input/
Output
Input,
pull-up
enabled
Home — Quadrature Decoder 0, HOME input
TA3 — Timer A ,Channel 3
Port C GPIO — This GPIO pin can be individually programmed
as an input or output pin.
After reset, the default state is HOME0.
To deactivate the internal pull-up resistor, clear bit 7 of the
GPIOC_PUR register.
SCLK0
(GPIOE4)
124 Schmitt
Input/
Output
Schmitt
Input/
Output
Input,
pull-up
enabled
SPI 0 Serial Clock — In the master mode, this pin serves as an
output, clocking slaved listeners. In slave mode, this pin serves
as the data clock input.
Port E GPIO — This GPIO pin can be individually programmed
as an input or output pin.
After reset, the default state is SCLK0.
To deactivate the internal pull-up resistor, clear bit 4 in the
GPIOE_PUR register.
Table 2-2 Signal and Package Information for the 128-Pin LQFP
Signal
Name Pin No. Type State
During
Reset Signal Description
56F8345 Technical Data, Rev. 17
28 Freescale Semiconductor
Preliminary
MOSI0
(GPIOE5)
126 Input/
Output
Input/
Output
In reset,
output is
disabled,
pull-up is
enabled
SPI 0 Master Out/Slave In — This serial data pin is an output
from a master device and an input to a slave device. The master
device places data on the MOSI line a half-cycle before the clock
edge the slave device uses to latch the data.
Port E GPIO — This GPIO pin can be individually programmed
as an input or output pin.
After reset, the default state is MOSI0.
To deactivate the internal pull-up resistor, clear bit 5 in the
GPIOE_PUR register.
MISO0
(GPIOE6)
125 Input/
Output
Input/
Output
Input,
pull-up
enabled
SPI 0 Master In/Slave Out — This serial data pin is an input to a
master device and an output from a slave device. The MISO line
of a slave device is placed in the high-impedance state if the
slave device is not selected. The slave device places data on the
MISO line a half-cycle before the clock edge the master device
uses to latch the data.
Port E GPIO — This GPIO pin can be individually programmed
as an input or output pin.
After reset, the default state is MISO0.
To deactivate the internal pull-up resistor, clear bit 6 in the
GPIOE_PUR register.
SS0
(GPIOE7)
123 Input
Input/
Output
Input,
pull-up
enabled
SPI 0 Slave Select — SS0 is used in slave mode to indicate to
the SPI module that the current transfer is to be received.
Port E GPIO — This GPIO pin can be individually programmed
as an input or output pin.
After reset, the default state is SS0.
To deactivate the internal pull-up resistor, clear bit 7 in the
GPIOE_PUR register.
Table 2-2 Signal and Package Information fo r the 128-Pin LQFP
Signal
Name Pin No. Type State
During
Reset Signal Description
Signal Pins
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 29
Preliminary
PHASEA1
(TB0)
(SCLK1)
(GPIOC0)
9Schmitt
Input
Schmitt
Input/
Output
Schmitt
Input/
Output
Schmitt
Input/
Output
Input,
pull-up
enabled
Phase A1 — Quadrature Decoder 1, PHASEA input for decoder
1.
TB0 — Timer B, Channel 0
SPI 1 Serial Clock — In the master mode, this pin serves as an
output, clocking slaved listeners. In slave mode, this pin serves
as the data clock input. To activate the SPI function, set the
PHSA_ALT bit in the SIM_GPS register. For details, see Part
6.5.8.
Port C GPIO — This GPIO pin can be individually programmed
as an input or output pin.
In the 56F8345, the default state after reset is PHASEA1.
In the 56F8145, the default state is not one of the functi ons
offered and must be reconfigured.
To deactivate the internal pull-up resistor, clear bit 0 in the
GPIOC_PUR register.
PHASEB1
(TB1)
(MOSI1)
(GPIOC1)
10 Schmitt
Input
Schmitt
Input/
Output
Schmitt
Input/
Output
Schmitt
Input/
Output
Input,
pull-up
enabled
Phase B1 — Quadrature Decoder 1, PHASEB input for decoder
1.
TB1 — Timer B, Channel 1
SPI 1 Master Out/Slave In — This serial data pin is an output
from a master device and an input to a slave device. The master
device places data on the MOSI line a half-cycle before the clock
edge the slave device uses to latch the data. To activate the SPI
function, set the PHSB_ALT bit in the SIM_GPS register. For
details, see Part 6.5.8.
Port C GPIO — This GPIO pin can be individually programmed
as an input or output pin.
In the 56F8345, the default state after reset is PHASEB1.
In the 56F8145, the default state is not one of the functi ons
offered and must be reconfigured.
To deactivate the internal pull-up resistor, clear bit 1 in the
GPIOC_PUR register.
Table 2-2 Signal and Package Information fo r the 128-Pin LQFP
Signal
Name Pin No. Type State
During
Reset Signal Description
56F8345 Technical Data, Rev. 17
30 Freescale Semiconductor
Preliminary
INDEX1
(TB2)
(MISO1)
(GPIOC2)
11 Schmitt
Input
Schmitt
Input/
Output
Schmitt
Input/
Output
Schmitt
Input/
Output
Input,
pull-up
enabled
Index1 — Quadrature Decoder 1, INDEX input
TB2 — Timer B, Channel 2
SPI 1 Master In/Slave Out — This serial data pin is an input to a
master device and output from a slave device. The MISO line of
a slave device is placed in the high-impedance state if the slave
device is not selected. The slave device places data on the
MISO line a half-cycle before the clock edge the master device
uses to latch the data. To activate the SPI function, set the
INDEX_ALT bit in the SIM_GPS register. See Part 6.5.8 for
details.
Port C GPIO — This GPIO pin can be individually programmed
as an input or output pin.
In the 56F8345, the default state after reset is INDEX1.
In the 56F8145, the default state is not one of the functi ons
offered and must be reconfigured.
To deactivate the internal pull-up resistor, clear bit 2 in the
GPIOC_PUR register.
Table 2-2 Signal and Package Information fo r the 128-Pin LQFP
Signal
Name Pin No. Type State
During
Reset Signal Description
Signal Pins
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 31
Preliminary
HOME1
(TB3)
(SS1)
(GPIOC3)
12 Schmitt
Input
Schmitt
Input/
Output
Schmitt
Input
Schmitt
Input/
Output
Input,
pull-up
enabled
Home — Quadrature Decoder 1, HOME input
TB3 — Timer B, Channel 3
SPI 1 Slave Select — In the master mode, this pin is used to
arbitrate multiple masters. In slave mode, this pin is used to
select the slave. To activate the SPI function, set the
HOME_ALT bit in the SIM_GPS register. See Part 6.5.8 for
details.
Port C GPIO — This GPIO pin can be individually programmed
as input or output pin.
In the 56F8345, the default state after reset is HOME1.
In the 56F8145, the default state is not one of the functions
offered and must be reconfigured.
To deactivate the internal pull-up resistor, clear bit 3 in the
GPIOC_PUR register.
PWMA0 58 Output In reset,
output is
disabled,
pull-up is
enabled
PWMA0 - 5 — These are six PWMA output pins.
PWMA1 60
PWMA2 61
PWMA3 63
PWMA4 64
PWMA5 66
ISA0
(GPIOC8)
104 Schmitt
Input
Schmitt
Input/
Output
Input,
pull-up
enabled
ISA0 - 2 — These three input current status pins are used for
top/bottom pulse width correction in complementary channel
operation for PWMA.
Port C GPIO — These GPIO pins can be individually
programmed as input or output pins.
In the 56F8345, these pins default to ISA functionality.
In the 56F8145, the default state is not one of the functi ons
offered and must be reconfigured.
To deactivate the internal pull-up resistor, clear the appropriate
bit of the GPIOC_PUR register. See Part 6.5.6 for details.
ISA1
(GPIOC9) 105
ISA2
(GPIOC10) 106
Table 2-2 Signal and Package Information fo r the 128-Pin LQFP
Signal
Name Pin No. Type State
During
Reset Signal Description
56F8345 Technical Data, Rev. 17
32 Freescale Semiconductor
Preliminary
FAULTA0 67 Schmitt
Input Input,
pull-up
enabled
FAULTA0 - 2 — These three fault input pins are used for
disabling selected PWMA outputs in cases where fault
conditions originate off-chip.
To deactivate the internal pull-up resistor, set the PWMA0 bit in
the SIM_PUDR register. See Part 6.5.6 for details.
FAULTA1 68
FAULTA2 69
FAULTA3 70 Schmitt
Input Input,
pull-up
enabled
FAULTA3 — This fault input pin is used for disabling selected
PWMA outputs in cases where fault conditions originate off-chi p.
To deactivate the internal pull-up resistor, set the PWMA1 bit in
the SIM_PUDR register. See Part 6.5.6 for details.
PWMB0 32 Output In reset,
output is
disabled,
pull-up is
enabled
PWMB0 - 5 — Six PWMB output pins.
PWMB1 33
PWMB2 34
PWMB3 37
PWMB4 38
PWMB5 39
ISB0
(GPIOD10)
48 Schmitt
Input
Schmitt
Input/
Output
Input,
pull-up
enabled
ISB0 - 2 — These three input current status pins are used for
top/bottom pulse width correction in complementary channel
operation for PWMB.
Port D GPIO — These GPIO pins can be individually
programmed as input or output pins.
At reset, these pins default to ISB functionality.
To deactivate the internal pull-up resistor, clear the appropriate
bit of the GPIOD_PUR register. See Part 6.5.6 for details.
ISB1
(GPIOD11) 50
ISB2
(GPIOD12) 51
FAULTB0 54 Schmitt
Input Input,
pull-up
enabled
FAULTB0 - 3 — These four fault input pins are used for
disabling selected PWMB outputs in cases where fault
conditions originate off-chip.
To deactivate the internal pull-up resistor, set the PWMB bit in
the SIM_PUDR register. See Part 6.5.6 for details.
FAULTB1 55
FAULTB2 56
FAULTB3 57
ANA0 80 Input Analog
Input ANA0 - 3 — Analog inputs to ADC A, channel 0
ANA1 81
ANA2 82
ANA3 83
Table 2-2 Signal and Package Information fo r the 128-Pin LQFP
Signal
Name Pin No. Type State
During
Reset Signal Description
Signal Pins
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 33
Preliminary
ANA4 84 Input Analog
Input ANA4 - 7 — Analog inputs to ADC A, channel 1
ANA5 85
ANA6 86
ANA7 87
VREFH 93 Input Analog
Input VREFH — Analog Reference Voltage High. VREFH must be less
than or equal to VDDA_ADC.
VREFP 92 Input/
Output Analog
Input/
Output
VREFP, VREFMID & VREFN — Internal pins for voltage reference
which are brought off-chip so that they can be bypassed.
Connect to a 0.1 μF low ESR capacitor.
VREFMID 91
VREFN 90
VREFLO 89 Input Analog
Input VREFLO — Analog Reference Voltage Low. This should normally
be connected to a low-noise V SSA.
ANB0 96 Input Analog
Input ANB0 - 3 — Analog inputs to ADC B, channel 0
ANB1 97
ANB2 98
ANB3 99
ANB4 100 Input Analog
Input ANB4 - 7 — Analog inputs to ADC B, channel 1
ANB5 101
ANB6 102
ANB7 103
TEMP_
SENSE 88 Output Analog
Output Temperature Sense Diode — This signal connects to an
on-chip diode that can be connected to one of the ADC inputs
and is used to monitor the temperature of the die. Must be
bypassed w it h a 0. 0 1 μF capacitor.
CAN_RX 121 Schmitt
Input Input,
pull-up
enabled
FlexCAN Receive Data — This is the CAN input. This pin has
an internal pull-up resistor.
To deactivate the internal pull-up resistor, set the CAN bit in the
SIM_PUDR register.
Table 2-2 Signal and Package Information fo r the 128-Pin LQFP
Signal
Name Pin No. Type State
During
Reset Signal Description
56F8345 Technical Data, Rev. 17
34 Freescale Semiconductor
Preliminary
CAN_TX 120 Open
Drain
Output
Open
Drain
Output
FlexCAN Transmit Data — CAN output with internal pull-up
enable at reset.*
* Note: If a pin is configured as open drain output mode, internal
pull-up will automatically be disabled when it outpu ts low.
Internal pull-up will be enabled unless it has been manually
disabled by clearing the corresponding bit in the PUREN register
of the GPIO module, when it outputs high.
If a pin is configured as push-pull output mode, intern al pull-up
will automatically be disabled, whether it outputs low or high.
TC0
(GPIOE8)
111 Schmitt
Input/
Output
Schmitt
Input/
Output
Input,
pull-up
enabled
TC0 - 1 — Timer C, Channels 0 and 1
Port E GPIO — These GPIO pins can be individually
programmed as input or output pins.
At reset, these pins default to Timer functionality.
To deactivate the internal pull-up resistor, clear the appropriate
bit of the GPIOE_PUR register. See Part 6.5. 6 for details.
TC1
(GPIOE9) 113
TD0
(GPIOE10)
107 Schmitt
Input/
Output
Schmitt
Input/
Output
Input,
pull-up
enabled
TD0 - TD3 — Timer D, Chan nels 0, 1, 2 and 3
Port E GPIO — These GPIO pins can be individually
programmed as input or output pins.
At reset, these pins default to Timer functionality.
To deactivate the internal pull-up resistor, clear the appropriate
bit of the GPIOE_PUR register. See Part 6.5. 6 for details.
TD1
(GPIOE11) 108
TD2
(GPIOE12) 109
TD3
(GPIOE13) 110
IRQA 52 Schmitt
Input Input,
pull-up
enabled
External Interrupt Request A and B — The IRQA and IRQB
inputs are asynchronous externa l interrupt requests during Stop
and Wait mode operation. During other operating modes, they
are synchronized external interrupt requests, which indicate an
external device is requesting servi ce. They can be programmed
to be level-sensitive or negative-edge triggered.
To deactivate the internal pull-up resistor, set the IRQ bit in the
SIM_PUDR register. See Part 6.5.6 for details.
IRQB 53
Table 2-2 Signal and Package Information fo r the 128-Pin LQFP
Signal
Name Pin No. Type State
During
Reset Signal Description
Signal Pins
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 35
Preliminary
RESET 78 Schmitt
Input Input,
pull-up
enabled
Reset — This input is a direct hardware reset on the processor.
When RESET is asserted low, the device is initialized and placed
in the reset state. A Schmitt trigger input is used for noise
immunity. The internal reset signal will be deasserted
synchronous with the internal clocks after a fixed number of
internal clocks.
To ensure complete hardware reset, RESET and TRST should
be asserted together. The only exception occurs in a debugging
environment when a hardware device reset is required and the
JTAG/EOnCE module must not be reset. In this case, assert
RESET, but do not assert TRST.
Note: The internal Power-On Reset will assert on initial
power-up.
To deactivate the internal pull-up resistor, set the RESET bit in
the SIM_PUDR register. See Part 6.5.6. for details.
RSTO 77 Output Output Reset Output — This output reflects the internal reset state of
the chip.
EXTBOOT Internal
Ground Schmitt
Input Input,
pull-up
enabled
External Boot — This input is tied to VDD to force the device to
boot from off-chip memory (assuming that the on-chip Flash
memory is not in a secure state). Otherwise, it is tied to ground.
For details, see Table 4-4.
Note: When this pin is tied low, the customer boot software
should disable the internal pull-up resistor by setting the XBOOT
bit of the SIM_PUDR; see Part 6.5.6.
Note: This pin is internally tied low (to VSS).
EMI_MODE Internal
Ground Schmitt
Input Input,
pull-up
enabled
External Memory Mode — This device will boot from internal
Flash memory under normal operation.
This function is also affected by EXTBOOT and the Flash
security mode; see Table 4-4 for details.
Note: When this pin is tied low, the customer boot software
should disable the internal pull-up resistor by setting the
EMI_MODE bit of the SIM_PUDR; see Part 6.5.6.
Note: This pin is internally tied low (to VSS).
Table 2-2 Signal and Package Information fo r the 128-Pin LQFP
Signal
Name Pin No. Type State
During
Reset Signal Description
56F8345 Technical Data, Rev. 17
36 Freescale Semiconductor
Preliminary
Part 3 On-Chip Clock Synthesis (OCCS)
3.1 Introduction
Refer to the OCCS chapter of the 56F8300 Peripheral User Manual for a full description of the OCCS.
The material contained here identifies the specific features of the OCCS design. Figure 3-1 shows the
specific OCCS block diagram to reference in the OCCS chapter of the 56F8300 Peripheral User Manual.
Figure 3-1 OCCS Block Diagram
3.2 External Clock Operation
The system clock can be derived from an external crystal, ceramic resonator, or an external system clock
signal. To generate a reference frequency using the internal oscillator, a reference crystal or ceramic
resonator must be connected between the EXTAL and XTAL pins.
3.2.1 Crystal Oscillator
The internal oscillator is designed to interface with a parallel-resonant crystal resonator in the frequency
range specified for the external crystal in Table 10-15. A recommended crystal oscillator circuit is shown
in Figure 3-2. Follow the crystal supplier’s recommendations when selecting a crystal, since crystal
parameters determine the component values required to provide maximum stability and reliable start-up.
MUX
EXTAL
XTAL
FEEDBACK
LCK
Prescaler CLK
Postscaler CLK
FOUT/2
Crystal
OSC
Loss of
Reference
Clock
Detector
Lock
Detector
ZSRC
Bus Interface & Control
FOUT
FREF
PLLDB PLLCOD
PLLCID
Bus
Interface
Loss of Reference
Clock Interrupt
SYS_CLK2
Source to SIM
MUX
CLKMODE
÷2
Prescaler
÷ (1,2,4,8)Postscaler
÷ (1,2,4,8)
MSTR_OSC
PLL
x (1 to 128)
External Clock Operation
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 37
Preliminary
The crystal and associated components should be mounted as near as possible to the EXTAL and XTAL
pins to minimize output distortion and start-up stabilization time.
Figure 3-2 Connecting to a Crystal Oscillator
Note: The OCCS_COHL bit must be set to 1 when a crystal oscillator is used. The reset condition on the
OCCS_COHL bit is 0. Please see the COHL bit in the Oscillator Control (OSCTL) register, discussed
in the 56F8300 Peripheral User’s Manual.
3.2.2 Ceramic Resonator (Default)
It is also possible to drive the internal oscillator with a ceramic resonator, assuming the overall system
design can tolerate the reduced signal integrity. A typical ceramic resonator circuit is shown in Figure 3-3.
Refer to the supplier’s recommendations when selecting a ceramic resonator and associated components.
The resonator and components should be mounted as near as possible to the EXTAL and XTAL pins.
Sample External Crystal Parameters:
Rz = 750 KΩ
Note: If the operating temperature range is limited to
below 85oC (105oC junction), then Rz = 10 Meg Ω
CLKMODE = 0
Crystal Frequency = 4 - 8MHz (optimized for 8MHz)
EXTAL EXTALXTAL XTAL
RZ
RZ
CL1 CL2
56F8345 Technical Data, Rev. 17
38 Freescale Semiconductor
Preliminary
Figure 3-3 Connecting a Ceramic Resonator
Note: The OCCS_COHL bit must be set to 0 when a ceramic resonator is used. The reset condition on the
OCCS_COHL bit is 0. Please see the COHL bit in the Oscillator Control (OSCTL) register, discussed
in the 56F8300 Peripheral User’s Manual.
3.2.3 External Clock Source
The recommended method of connecting an external clock is illustrated in Figure 3-4. The external clock
source is connected to XTAL and the EXTAL pin is grounded. Set OCCS_COHL bit high when using an
external clock source as well.
Figure 3-4 Connecting an External Clock Signal Register
3.3 Registers
When referring to the register definitions for the OCCS in the 56F8300 Peripheral User Manual, use the
register definitions without the internal Relaxation Oscillator, since the 56F8345/56F8145 devices do
NOT contain this oscillator.
Part 4 Memory Map
4.1 Introduction
The 56F8345 and 56F8145 devices are 16-bit motor-control chips based on the 56800E core. These parts
use a Harvard-style architecture with two independent memory spaces for Data and Program. On-chip
EXTAL XTAL
R
z
Sample External Ceramic Resonator Parameters:
Rz = 750 KΩ
EXTAL XTAL
R
z
C1
CL1 CL2 C2
Resonator Frequency = 4 - 8MHz (optimized for 8MHz)
3 Terminal
2 Terminal
CLKMODE = 0
XTAL EXTAL
External VSS
Clock
Note: When using an external clocking
source with this configuration, the input
“CLKMODE” should be high and COHL bit in
the OSCTL register should be set to 1.
Program Map
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 39
Preliminary
RAM and Flash memories are used in both spaces.
This section provides memory maps for:
• Program Address Space, including the Interrupt Vector Table
• Data Address Space, including the EOnCE Memory and Peripheral Memory Maps
On-chip memory sizes for each device are summarized in Table 4-1. Flash memories’ restrictions are
identified in the “Use Restrictions” column of Table 4-1.
Note: Data Flash and Program RAM are NOT available on the 56F8145 device.
4.2 Program Map
The Program memory map is located in Table 4-4. The operating mode control bits (MA and MB) in the
Operating Mode Register (OMR) control the Program memory map. At reset, these bits are set as indicated
in Table 4-2.
EXT_BOOT = EMI_MODE = 0 and cannot be changed in the 56F8345 or 56F8145.
Note: Program RAM is NOT available on the 56F8145 device.
Table 4-1 Chip Memory Configurations
On-Chip Memory 56F8345 56F8145 Use Restrictions
Program Flash 128KB 128KB Erase / Program via Flash interface unit and word writes to
CDBW
Data Flash 8KB — Erase / Program via Flash interface unit and word writes to
CDBW. Data Flash can be read via eithe r CDBR or XDB2,
but not by both simultaneously
Program RAM 4KB — None
Data RAM 8KB 8KB None
Program Boot Flash 8KB 8KB Erase / Program via Flash Interface unit and word writes to
CDBW
Table 4-2 OMR MB/MA Value at Reset1
OMR MB =
Flash Secured
State2,3
OMR MA =
EXTBOOT Pin Chip Operating Mode
0 0 Mode 0 – Internal Boot; EMI is configured to use 16 address lines; Flash
Memory is secured; external P-space is not allowed; the EOnCE is disabled
0 1 Not valid; cannot boot externally if the Flash is secured and will actually
configure to 00 state
1 0 Mode 0 – Internal Boot; EMI is configured to use 16 address lines
56F8345 Technical Data, Rev. 17
40 Freescale Semiconductor
Preliminary
After reset, the OMR MA bit can be changed and will have an effect on the P-space memory map, as shown
in Table 4-3. Changing the OMR MB bit will have no effect.
Table 4-4 shows the memory map options of the 56F8345/56F8145. The two right columns cannot be
used, since the EMI pins are not provided in the package; therefore, only the Mode 0 column is relevant.
Note: Program RAM is NOT available on the 56F8145 device.
1 1 Mode 1 – External Boot; Flash Memory is not secured; EMI configuration is
determined by the state of the EMI_MODE pin
1. Information in shaded areas not applicable to 56F8345/56F8145.
2. This bit is only c onfigured at reset. If the Flash secured state changes, this will not be reflected in MB until the next reset.
3. Changing MB in software will not affect Flash memory security.
Table 4-3 Changing OMR MA Value During Normal Operation
OMR MA Chip Operating Mode
0 Use internal P-space memory map configuration
11
1. Setting this bit can cause unpredictable results and is not recommended, since the EMI is not functional in this package.
Use external P-space memory map configuration – If MB = 0 at reset, changing this bit has no effect.
Table 4-2 OMR MB/MA Value at Reset1 (Continued)
OMR MB =
Flash Secured
State2,3
OMR MA =
EXTBOOT Pin Chip Operating Mode
Interrupt Vector Table
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 41
Preliminary
1. Cannot be used since MA = EXTBOOT = 0 and the EMI is not available; information in shaded areas not applicable to
56F8345/56F8145.
2. This mode provides maximum compatibility with 56F80x parts wh ile operating externally.
3. “EMI_MODE = 0”, EMI_MODE pin is tied to ground at boot up .
4. “EMI_MODE = 1”, EMI_MODE pin is tied to VDD at boot up.
5. Not accessible in this part, since the EMI is not fully pinned out in this package; information in shaded areas not applicable to
56F8345/56F8145.
4.3 Interrupt Vector Table
Table 4-5 provides the reset and interrupt priority structure, including on-chip peripherals. The table is
organized with higher-priority vectors at the top and lower-priority interrupts lower in the table. The
priority of an interrupt can be assigned to different levels, as indicated, allowing some control over
interrupt priorities. All level 3 interrupts will be serviced before level 2, and so on. For a selected priority
level, the lowest vector number has the highest priority.
The location of the vector table is determined by the Vector Base Address (VBA) register. Please see Part
5.6.11 for the reset value of the VBA.
In some configurations, the reset address and COP reset address will correspond to vector 0 and 1 of the
interrupt vector table. In these instances, the first two locations in the vector table must contain branch or
Table 4-4 Program Memory Map at Reset
Begin/End
Address
Mode 0 (MA = 0) Mode 11 (MA = 1)
Internal Boot External Boot
Internal Boot
16-Bit External Address Bus EMI_MODE = 02, 3
16-Bit External Address Bus EMI_MODE = 14
20-Bit External Address Bus
P:$1F FFFF
P:$10 0000 External Program Memory5External Program Memory5External Program Memory5
P:$0F FFFF
P:$03 0000 External Program RAM5
COP Reset Address = 02 0002
Boot Location = 02 0000
P:$02 FFFF
P:$02 F800 On-Chip Program RAM
4KB On-Chip Program RAM
4KB
P:$02 F7FF
P:$02 1000 Reserved
116KB
P:$02 0FFF
P:$02 0000 Boot Flash
8KB
COP Reset Address = 02 0002
Boot Location = 02 0000
Boot Flash
8KB
(Not Used for Boot in this Mode)
P:$01 FFFF
P:$01 0000 External Program RAM5Internal Program Flash
128KB
P:$00 FFFF
P:$00 0000 Internal Program Flash
128KB External Program RAM5
COP Reset Address = 00 0002
Boot Location = 00 0000
56F8345 Technical Data, Rev. 17
42 Freescale Semiconductor
Preliminary
JMP instructions. All other entries must contain JSR instructions.
Note: PWMA, FlexCAN, Quadrature Decoder 1, and Quad Timers B and D are NOT available on the
56F8145 device.
Table 4-5 Interrupt Vector Table Contents1
Peripheral Vector
Number Priority
Level Vector Base
Address + Interrupt Function
Reserved for Reset Overlay2
Reserved for COP Reset Overlay2
core 2 3 P:$04 Illegal Instruction
core 3 3 P:$06 SW Interrupt 3
core 4 3 P:$08 HW Stack Overflow
core 5 3 P:$0A Misaligned Long Word Access
core 6 1-3 P:$0C OnCE Step Counter
core 7 1-3 P:$0E OnCE Breakpoint Unit 0
Reserved
core 9 1-3 P:$12 OnCE Trace Buffer
core 10 1-3 P:$14 OnCE Transmit Register Empty
core 11 1-3 P:$16 OnCE Receive Register Full
Reserved
core 14 2 P:$1C SW Interrupt 2
core 15 1 P:$1E SW Interrupt 1
core 16 0 P:$20 SW Interrupt 0
core 17 0-2 P:$22 IRQA
core 18 0-2 P:$24 IRQB
Reserved
LVI 20 0-2 P:$28 Low Voltage Detector (power sens e)
PLL 21 0-2 P:$2A PLL
FM 22 0-2 P:$2C FM Access Error Interrupt
FM 23 0-2 P:$2E FM Command Complete
FM 24 0-2 P:$30 FM Command, data and address Buffers Empty
Reserved
FLEXCAN 26 0-2 P:$34 FLEXCAN Bus Off
FLEXCAN 27 0-2 P:$36 FLEXCAN Error
FLEXCAN 28 0-2 P:$38 FLEXCAN Wake Up
Interrupt Vector Table
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 43
Preliminary
FLEXCAN 29 0-2 P:$3A FLEXCAN Message Buffer Interrupt
GPIOF 30 0-2 P:$3C GPIO F
GPIOE 31 0-2 P:$3E GPIO E
GPIOD 32 0-2 P:$40 GPIO D
GPIOC 33 0-2 P:$42 GPIO C
GPIOB 34 0-2 P:$44 GPIO B
GPIOA 35 0-2 P:$46 GPIO A
Reserved
SPI1 38 0-2 P:$4C SPI 1 Receiver Full
SPI1 39 0-2 P:$4E SPI 1 Transmitter Empty
SPI0 40 0-2 P:$50 SPI 0 Receiver Full
SPI0 41 0-2 P:$52 SPI 0 Transmitter Empty
SCI1 42 0-2 P:$54 SCI 1 Transmitter Empty
SCI1 43 0-2 P:$56 SCI 1 Transmitter Idle
Reserved
SCI1 45 0-2 P:$5A SCI 1 Receiver Error
SCI1 46 0-2 P:$5C SCI 1 Receiver Full
DEC1 47 0-2 P:$5E Quadrature Decoder #1 Home Switch or Watchdog
DEC1 48 0-2 P:$60 Quadrature Decoder #1 INDEX Pulse
DEC0 49 0-2 P:$62 Quadrature Decoder #0 Home Switch or Watchdog
DEC0 50 0-2 P:$64 Quadrature Decoder #0 INDEX Pulse
Reserved
TMRD 52 0-2 P:$68 Timer D, Cha nnel 0
TMRD 53 0-2 P:$6A Timer D, Channel 1
TMRD 54 0-2 P:$6C Timer D, Channe l 2
TMRD 55 0-2 P:$6E Timer D, Channel 3
TMRC 56 0-2 P:$70 Timer C, Channe l 0
TMRC 57 0-2 P:$72 Timer C, Channe l 1
TMRC 58 0-2 P:$74 Timer C, Channe l 2
TMRC 59 0-2 P:$76 Timer C, Channe l 3
Table 4-5 Interrupt Vector Table Contents1 (Continued)
Peripheral Vector
Number Priority
Level Vector Base
Address + Interrupt Function
56F8345 Technical Data, Rev. 17
44 Freescale Semiconductor
Preliminary
TMRB 60 0-2 P:$78 Timer B, Chan nel 0
TMRB 61 0-2 P:$7A Timer B, Channel 1
TMRB 62 0-2 P:$7C Timer B, Channel 2
TMRB 63 0-2 P:$7E Timer B, Channel 3
TMRA 64 0-2 P:$80 Timer A, Chan nel 0
TMRA 65 0-2 P:$82 Timer A, Chan nel 1
TMRA 66 0-2 P:$84 Timer A,Ch annel 2
TMRA 67 0-2 P:$86 Timer A, Chan nel 3
SCI0 68 0-2 P:$88 SCI 0 Transmitter Empty
SCI0 69 0-2 P:$8A SCI 0 Transmitter Idle
Reserved
SCI0 71 0-2 P:$8E SCI 0 Receiver Error
SCI0 72 0-2 P:$90 SCI 0 Receiver Full
ADCB 73 0-2 P:$92 ADC B Conversion Compete / End of Scan
ADCA 74 0-2 P:$94 ADC A Conversion Complete / End of Scan
ADCB 75 0-2 P:$96 ADC B Zero Crossing or Limit Error
ADCA 76 0-2 P:$98 ADC A Zero Crossing or Limit Error
PWMB 77 0-2 P:$9A Reload PWM B
PWMA 78 0-2 P:$9C Reload PWM A
PWMB 79 0-2 P:$9E PWM B Fau lt
PWMA 80 0-2 P:$A0 PWM A Fault
core 81 - 1 P:$A2 SW Interrupt LP
1. Two words are allocated for each entry in the vector table. This does not allow the full address range to be referenced
from the vector table, providing only 19 bits of address.
2. If the VBA is set to $0200 (or VBA = 0000 for Mode 1, EMI_MODE = 0), the first two locations of the vector table are
the chip reset addresses; therefore, these locations are not interrupt vectors.
Table 4-5 Interrupt Vector Table Contents1 (Continued)
Peripheral Vector
Number Priority
Level Vector Base
Address + Interrupt Function
Data Map
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 45
Preliminary
4.4 Data Map
Note: Data Flash is NOT available on the 56F8145 device.
4.5 Flash Memory Map
Figure 4-1 illustrates the Flash Memory (FM) map on the system bus.
The Flash Memory is divided into three functional blocks. The Program and boot memories reside on the
Program Memory buses. They are controlled by one set of banked registers. Data Memory Flash resides
on the Data Memory buses and is controlled separately by its own set of banked registers.
The top nine words of the Program Memory Flash are treated as special memory locations. The content of
these words is used to control the operation of the Flash Controller. Because these words are part of the
Flash Memory content, their state is maintained during power-down and reset. During chip initialization,
the content of these memory locations is loaded into Flash Memory control registers , detailed in the Flash
Memory chapter of the 56F8300 Peripheral User Manual. These configuration parameters are located
between $00_FFF7 and $00_FFFF.
Table 4-6 Data Memory Map1, 2
1. Information in shad ed areas not applicable to 56F8345/56F8145.
2. All addresses are 16-bit Word addresses, not byte addresses.
Begin/End Address EX = 03
3. In the Operating Mode Regist er.
EX = 14
4. Setting EX = 1 is not recommended in the 56F8345/56F8145, since the EMI is not functional in this package.
X:$FF FFFF
X:$FF FF00 EOnCE
256 locations allocated EOnCE
256 locations allocated
X:$FF FEFF
X:$01 0000 External Memory External Memory
X:$00 FFFF
X:$00 F000 On-Chip Peripherals
4096 locations allocated On-Chip Peripherals
4096 locations allocated
X:$00 EFFF
X:$00 2000 External Memory External Memory
X:$00 1FFF
X:$00 1000 On-Chip Data Flash
8KB
X:$00 0FFF
X:$00 0000 On-Chip Data RAM
8KB5
5. The Data RAM is organized as a 2K x 32-bit memory to allow single-cycle, long-word operations.
56F8345 Technical Data, Rev. 17
46 Freescale Semiconductor
Preliminary
Figure 4-1 Flash Array Memory Maps
Table 4-7 shows the page and sector sizes used within each Flash memory block on the chip.
Note: Data Flash is NOT available on the 56F8145 device.
Please see the 56F8300 Peripheral User Manual for additional Flash information.
4.6 EOnCE Memory Map
Table 4-7. Flash Memory Partitions
Flash Size Sectors Sector Size Page Size
Program Flash 128KB 16 4K x 16 bits 512 x 16 bits
Data Flash 8KB 16 256 x 16 bits 256 x 16 bits
Boot Flash 8KB 4 1K x 16 bits 256 x 16 bits
Table 4-8 EOnCE Memory Map
Address Register Acronym Register Name
Reserved
X:$FF FF8A OESCR External Signal Control Register
Reserved
X:$FF FF8E OBCNTR Breakpoint Unit [0] Counter
BOOT_FLASH_START = $02_0000
BOOT_FLASH_START + $1F F F
Block 0 Odd
Block 0 Even
PROG_FLASH_START + $00_FFFF
. . .
8KB
Boot
Reserved
Configure Field
PROG_FLASH_START + $00_FFF7
PROG_FLASH_START + $00_FFF6
128KB
PROG_FLASH_START = $00_0000
FM_PROG_MEM_TOP = $00_FFFF
BLOCK 0 Odd (2 Bytes) $00_0003
BLOCK 0 Even (2 Bytes) $00_0002
BLOCK 0 Odd (2 Bytes) $00_0001
BLOCK 0 Even (2 Bytes) $00_0000
FM_BASE + $14
Banked Registers
Unbanked Registers
8KB
FM_BASE + $00
DATA_FLASH_START + $0FFF
DATA_FLASH_START + $0000
Dat a Mem ory
Program Memory
Note: Data Flash is
NOT available in the
56F8145 device.
Peripheral Memory Mapped Registers
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 47
Preliminary
4.7 Peripheral Memory Mapped Registers
On-chip peripheral registers are part of the data memory map on the 56800E series. These locations may
be accessed with the same addressing modes used for ordinary Data memory, except all peripheral
registers should be read/written using word accesses only.
Table 4-9 summarizes base addresses for the set of peripherals on the 56F8345 and 56F8145 devices.
Peripherals are listed in order of the base address.
The following tables list all of the peripheral registers required to control or access the peripherals.
Note: Features in italics are NOT available in the 56F8145 device.
Reserved
X:$FF FF90 OBMSK (32 bits) Breakpoint 1 Unit [0] Mask Register
X:$FF FF91 — Breakpoint 1 Unit [0] Mask Register
X:$FF FF92 OBAR2 (32 bits) Breakpoint 2 Unit [0] Address Register
X:$FF FF93 — Breakpoint 2 Unit [0] Address Register
X:$FF FF94 OBAR1 (24 bits) Breakpoint 1 Unit [0] Address Register
X:$FF FF95 — Breakpoint 1 Unit [0] Address Register
X:$FF FF96 OBCR (24 bits) Breakpoint Unit [0] Control Register
X:$FF FF97 — Breakpoint Unit [0] Control Regi ster
X:$FF FF98 OTB (21-24 bits/stage) Trace Buffer Register Stages
X:$FF FF99 — Trace Buffer Register Stages
X:$FF FF9A OTBPR (8 bits) Trace Buffer Pointer Register
X:$FF FF9B OTBCR Trace Buffer Control Register
X:$FF FF9C OBASE (8 bits) Peripheral Base Address Register
X:$FF FF9D OSR Status Register
X:$FF FF9E OSCNTR (24 bits) Instruction Step Counter
X:$FF FF9F — Instructi on Step Counter
X:$FF FFA0 OCR (bits) Control Register
Reserved
X:$FF FFFC OCLSR (8 bits) Co r e Lock / Unlock Status Register
X:$FF FFFD OTXRXSR (8 bits) Transmit and Receive Status and Control Register
X:$FF FFFE OTX / ORX (32 bits) Transmit Register / Receive Register
X:$FF FFFF OTX1 / ORX1 Transmit Register Upper Word
Receive Register Upper Word
Table 4-8 EOnCE Memory Map (Continued)
Address Register Acronym Register Name
56F8345 Technical Data, Rev. 17
48 Freescale Semiconductor
Preliminary
Table 4-9 Data Memory Peripheral Base Address Map Summary
Peripheral Prefix Base Address Table Number
External Memory Interface EMI X:$00 F020 4-10
Timer A TMRA X:$00 F040 4-11
Timer B TMRB X:$00 F080 4-12
Timer C TMRC X:$00 F0C0 4-13
Timer D TMRD X:$00 F100 4-14
PWM APWMA X:$00 F140 4-15
PWM B PWMB X:$00 F160 4-16
Quadrature Decoder 0 DEC0 X:$00 F180 4-17
Quadrature Decoder 1 DEC1 X:$00 F190 4-18
ITCN ITCN X:$00 F1A0 4-19
ADC A ADCA X:$00 F200 4-20
ADC B ADCB X:$00 F240 4-21
Temperature Sensor TSENSOR X:$00 F270 4-22
SCI #0 SCI0 X:$00 F280 4-23
SCI #1 SCI1 X:$00 F290 4-24
SPI #0 SPI0 X:$00 F2A0 4-25
SPI #1 SPI1 X:$00 F2B0 4-26
COP COP X:$00 F2C0 4-27
PLL, OSC CLKGEN X:$00 F2D0 4-28
GPIO Port A GPIOA X:$00 F2E0 4-29
GPIO Port B GPIOB X:$00 F300 4-30
GPIO Port C GPIOC X:$00 F310 4-31
GPIO Port D GPIOD X:$00 F320 4-32
GPIO Port E GPIOE X:$00 F330 4-33
GPIO Port F GPIOF X:$00 F340 4-34
SIM SIM X:$00 F350 4-35
Power Supervisor LVI X:$00 F360 4-36
FM FM X:$00 F400 4-37
FlexCAN FC X:$00 F800 4-38
Peripheral Memory Mapped Registers
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 49
Preliminary
Table 4-10 External Memory Integration Registers Address Map
(EMI_BASE = $00 F020)
Register
Acronym Address
Offset Register Description Reset Values
CSBAR 0 $0 Chip Select Base Address Register 0 0 x 0004 = 64K since
EXTBOOT = EMI_MODE
= 0
This table added to provide complete information, but this peripheral
is not functional in the 56F8345/56F8145 package
CSBAR 1 $1 Chip Select Base Address Register 1 0 x 0004 = 64K since
EMI_MODE = 0
CSBAR 2 $2 Chip Select Base Address Register 2
CSBAR 3 $3 Chip Select Base Address Register 3
CSBAR 4 $4 Chip Select Base Address Register 4
CSBAR 5 $5 Chip Select Base Address Register 5
CSBAR 6 $6 Chip Select Base Address Register 6
CSBAR 7 $7 Chip Select Base Address Register 7
CSOR 0 $8 Chip Select Option Register 0
CSOR 1 $9 Chip Select Option Register 1
CSOR 2 $A Chip Select Option Register 2
CSOR 3 $B Chip Select Option Register 3
CSOR 4 $C Chip Select Option Register 4
CSOR 5 $D Chip Select Option Register 5
CSOR 6 $E Chip Select Option Register 6
CSOR 7 $F Chip Select Option Reg ister 7
CSTC 0 $10 Chip Select Timing Control Register 0
CSTC 1 $11 Chip Select Timing Control Register 1
CSTC 2 $12 Chip Select Timing Control Register 2
CSTC 3 $13 Chip Select Timing Control Register 3
CSTC 4 $14 Chip Select Timing Control Register 4
CSTC 5 $15 Chip Select Timing Control Register 5
CSTC 6 $16 Chip Select Timing Control Register 6
CSTC 7 $17 Chip Select Timing Control Register 7
BCR $18 Bus Control Register
Table 4-11 Quad Timer A Registers Address Map
(TMRA_BASE = $00 F040)
Register Acronym Address Offset Register Description
TMRA0_CMP1 $0 Compare Register 1
56F8345 Technical Data, Rev. 17
50 Freescale Semiconductor
Preliminary
TMRA0_CMP2 $1 Compare Register 2
TMRA0_CAP $2 Capture Register
TMRA0_LOAD $3 Load Register
TMRA0_HOLD $4 Hold Register
TMRA0_CNTR $5 Counter Register
TMRA0_CTRL $6 Control Register
TMRA0_SCR $7 Status and Control Register
TMRA0_CMPLD1 $8 Comparator Load Register 1
TMRA0_CMPLD2 $9 Comparator Load Register 2
TMRA0_COMSCR $A Comparator Status and Control Re gister
Reserved
TMRA1_CMP1 $10 Compare Register 1
TMRA1_CMP2 $11 Compare Register 2
TMRA1_CAP $12 Capture Register
TMRA1_LOAD $13 Load Register
TMRA1_HOLD $14 Hold Register
TMRA1_CNTR $15 Counter Register
TMRA1_CTRL $16 Control Register
TMRA1_SCR $17 Status and Control Register
TMRA1_CMPLD1 $18 Comparator Load Register 1
TMRA1_CMPLD2 $19 Comparator Load Register 2
TMRA1_COMSCR $1A Comparator Status and Control Register
Reserved
TMRA2_CMP1 $20 Compare Register 1
TMRA2_CMP2 $21 Compare Register 2
TMRA2_CAP $22 Capture Register
TMRA2_LOAD $23 Load Register
TMRA2_HOLD $24 Hold Register
TMRA2_CNTR $25 Counter Register
TMRA2_CTRL $26 Control Register
TMRA2_SCR $27 Status and Control Register
TMRA2_CMPLD1 $28 Comparator Load Register 1
Table 4-11 Quad Timer A Registers Address Map (Continued)
(TMRA_BASE = $00 F040)
Register Acronym Address Offset Register Description
Peripheral Memory Mapped Registers
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 51
Preliminary
TMRA2_CMPLD2 $29 Comparator Load Register 2
TMRA2_COMSCR $2A Comparator Status and Control Register
Reserved
TMRA3_CMP1 $30 Compare Register 1
TMRA3_CMP2 $31 Compare Register 2
TMRA3_CAP $32 Capture Register
TMRA3_LOAD $33 Load Register
TMRA3_HOLD $34 Hold Register
TMRA3_CNTR $35 Counter Register
TMRA3_CTRL $36 Control Register
TMRA3_SCR $37 Status and Control Register
TMRA3_CMPLD1 $38 Comparator Load Register 1
TMRA3_CMPLD2 $39 Comparator Load Register 2
TMRA3_COMSCR $3A Comparator Status and Control Register
Table 4-12 Quad Timer B Registers Address Map
(TMRB_BASE = $00 F080)
Quad Timer B is NOT available in the 56F8145 device
Register Acronym Address Offset Register Description
TMRB0_CMP1 $0 Compare Register 1
TMRB0_CMP2 $1 Compare Register 2
TMRB0_CAP $2 Capture Register
TMRB0_LOAD $3 Load Register
TMRB0_HOLD $4 Hold Register
TMRB0_CNTR $5 Counter Register
TMRB0_CTRL $6 Control Register
TMRB0_SCR $7 Status and Control Register
TMRB0_CMPLD1 $8 Comparator Load Register 1
TMRB0_CMPLD2 $9 Comparator Load Register 2
TMRB0_COMSCR $A Comparator Status and Control Register
Reserved
TMRB1_CMP1 $10 Compare Register 1
Table 4-11 Quad Timer A Registers Address Map (Continued)
(TMRA_BASE = $00 F040)
Register Acronym Address Offset Register Description
56F8345 Technical Data, Rev. 17
52 Freescale Semiconductor
Preliminary
TMRB1_CMP2 $11 Compare Register 2
TMRB1_CAP $12 Capture Register
TMRB1_LOAD $13 Load Register
TMRB1_HOLD $14 Hold Register
TMRB1_CNTR $15 Counter Register
TMRB1_CTRL $16 Control Register
TMRB1_SCR $17 Status and Control Register
TMRB1_CMPLD1 $18 Comparator Load Register 1
TMRB1_CMPLD2 $19 Comparator Load Register 2
TMRB1_COMSCR $1A Comparator Status and Control Register
Reserved
TMRB2_CMP1 $20 Compare Register 1
TMRB2_CMP2 $21 Compare Register 2
TMRB2_CAP $22 Capture Register
TMRB2_LOAD $23 Load Register
TMRB2_HOLD $24 Hold Register
TMRB2_CNTR $25 Counter Register
TMRB2_CTRL $26 Control Register
TMRB2_SCR $27 Status and Control Register
TMRB2_CMPLD1 $28 Comparator Load Register 1
TMRB2_CMPLD2 $29 Comparator Load Register 2
TMRB2_COMSCR $2A Comparator Status and Control Register
Reserved
TMRB3_CMP1 $30 Compare Register 1
TMRB3_CMP2 $31 Compare Register 2
TMRB3_CAP $32 Capture Register
TMRB3_LOAD $33 Load Register
Table 4-12 Quad Timer B Registers Address Map (Continued)
(TMRB_BASE = $00 F080)
Quad Timer B is NOT available in the 56F8145 device
Register Acronym Address Offset Register Description
Peripheral Memory Mapped Registers
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 53
Preliminary
TMRB3_HOLD $34 Hold Register
TMRB3_CNTR $35 Counter Register
TMRB3_CTRL $36 Control Register
TMRB3_SCR $37 Status and Control Register
TMRB3_CMPLD1 $38 Comparator Load Register 1
TMRB3_CMPLD2 $39 Comparator Load Register 2
TMRB3_COMSCR $3A Comparator Status and Control Register
Table 4-13 Quad Timer C Registers Address Map
(TMRC_BASE = $00 F0C0)
Register Acronym Address Offset Register Description
TMRC0_CMP1 $0 Compare Register 1
TMRC0_CMP2 $1 Compare Register 2
TMRC0_CAP $2 Capture Register
TMRC0_LOAD $3 Load Register
TMRC0_HOLD $4 Hold Register
TMRC0_CNTR $5 Counter Register
TMRC0_CTRL $6 Control Register
TMRC0_SCR $7 Status and Control Register
TMRC0_CMPLD1 $8 Comparator Load Register 1
TMRC0_CMPLD2 $9 Comparator Load Register 2
TMRC0_COMSCR $A Comparator Status and Control Register
Reserved
TMRC1_CMP1 $10 Compare Register 1
TMRC1_CMP2 $11 Compare Register 2
TMRC1_CAP $12 Capture Register
TMRC1_LOAD $13 Load Register
TMRC1_HOLD $14 Hold Register
TMRC1_CNTR $15 Counter Register
TMRC1_CTRL $16 Control Register
TMRC1_SCR $17 Status and Control Register
TMRC1_CMPLD1 $18 Comparator Load Register 1
Table 4-12 Quad Timer B Registers Address Map (Continued)
(TMRB_BASE = $00 F080)
Quad Timer B is NOT available in the 56F8145 device
Register Acronym Address Offset Register Description
56F8345 Technical Data, Rev. 17
54 Freescale Semiconductor
Preliminary
TMRC1_CMPLD2 $19 Comparator Load Register 2
TMRC1_COMSCR $1A Comparato r Status and Control Register
Reserved
TMRC2_CMP1 $20 Compare Register 1
TMRC2_CMP2 $21 Compare Register 2
TMRC2_CAP $22 Capture Register
TMRC2_LOAD $23 Load Register
TMRC2_HOLD $24 Hold Register
TMRC2_CNTR $25 Counter Register
TMRC2_CTRL $26 Control Register
TMRC2_SCR $27 Status and Control Register
TMRC2_CMPLD1 $28 Comparator Load Register 1
TMRC2_CMPLD2 $29 Comparator Load Register 2
TMRC2_COMSCR $2A Comparato r Status and Control Register
Reserved
TMRC3_CMP1 $30 Compare Register 1
TMRC3_CMP2 $31 Compare Register 2
TMRC3_CAP $32 Capture Register
TMRC3_LOAD $33 Load Register
TMRC3_HOLD $34 Hold Register
TMRC3_CNTR $35 Counter Register
TMRC3_CTRL $36 Control Register
TMRC3_SCR $37 Status and Control Register
TMRC3_CMPLD1 $38 Comparator Load Register 1
TMRC3_CMPLD2 $39 Comparator Load Register 2
TMRC3_COMSCR $3A Comparato r Status and Control Register
Table 4-14 Quad Timer D Registers Address Map
(TMRD_BASE = $00 F100)
Quad Timer D is NOT available in the 56F8145 device
Register Acronym Address Offset Register Description
TMRD0_CMP1 $0 Compare Register 1
TMRD0_CMP2 $1 Compare Register 2
Table 4-13 Quad Timer C Registers Address Map (Continued)
(TMRC_BASE = $00 F0C0)
Register Acronym Address Offset Register Description
Peripheral Memory Mapped Registers
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 55
Preliminary
TMRD0_CAP $2 Capture Register
TMRD0_LOAD $3 Load Register
TMRD0_HOLD $4 Hold Register
TMRD0_CNTR $5 Counter Register
TMRD0_CTRL $6 Control Register
TMRD0_SCR $7 Status and Control Register
TMRD0_CMPLD1 $8 Comparator Load Register 1
TMRD0_CMPLD2 $9 Comparator Load Register 2
TMRD0_COMSCR $A Comparator Status and Control Register
Reserved
TMRD1_CMP1 $10 Compare Register 1
TMRD1_CMP2 $11 Compare Register 2
TMRD1_CAP $12 Capture Register
TMRD1_LOAD $13 Load Register
TMRD1_HOLD $14 Hold Register
TMRD1_CNTR $15 Counter Register
TMRD1_CTRL $16 Control Register
TMRD1_SCR $17 Status and Control Register
TMRD1_CMPLD1 $18 Comparator Load Register 1
TMRD1_CMPLD2 $19 Comparator Load Register 2
TMRD1_COMSCR $1A Comparato r Status and Control Register
Reserved
TMRD2_CMP1 $20 Compare Register 1
TMRD2_CMP2 $21 Compare Register 2
TMRD2_CAP $22 Capture Register
TMRD2_LOAD $23 Load Register
TMRD2_HOLD $24 Hold Register
TMRD2_CNTR $25 Counter Register
TMRD2_CTRL $26 Control Register
TMRD2_SCR $27 Status and Control Register
TMRD2_CMPLD1 $28 Comparator Load Register 1
TMRD2_CMPLD2 $29 Comparator Load Register 2
Table 4-14 Quad Timer D Registers Address Map (Continued)
(TMRD_BASE = $00 F100)
Quad Timer D is NOT available in the 56F8145 device
Register Acronym Address Offset Register Description
56F8345 Technical Data, Rev. 17
56 Freescale Semiconductor
Preliminary
TMRD2_COMSCR $2A Comparato r Status and Control Register
Reserved
TMRD3_CMP1 $30 Compare Register 1
TMRD3_CMP2 $31 Compare Register 2
TMRD3_CAP $32 Capture Register
TMRD3_LOAD $33 Load Register
TMRD3_HOLD $34 Hold Register
TMRD3_CNTR $35 Counter Register
TMRD3_CTRL $36 Control Register
TMRD3_SCR $37 Status and Control Register
TMRD3_CMPLD1 $38 Comparator Load Register 1
TMRD3_CMPLD2 $39 Comparator Load Register 2
TMRD3_COMSCR $3A Comparato r Status and Control Register
Table 4-15 Pulse Width Modulator A Registers Address Map
(PWMA_BASE = $00 F140)
PWMA is NOT available in the 56F8145 device
Register Acronym Address Offset Register Description
PWMA_PMCTL $0 Control Register
PWMA_PMFCTL $1 Fault Control Register
PWMA_PMFSA $2 Fault Status Acknowledge Register
PWMA_PMOUT $3 Output Control Register
PWMA_PMCNT $4 Counter Register
PWMA_PWMCM $5 Counter Modulo Register
PWMA_PWMVAL0 $6 Value Register 0
PWMA_PWMVAL1 $7 Value Register 1
PWMA_PWMVAL2 $8 Value Register 2
PWMA_PWMVAL3 $9 Value Register 3
PWMA_PWMVAL4 $A Value Register 4
PWMA_PWMVAL5 $B Value Register 5
PWMA_PMDEADTM $C Dead Time Register
PWMA_PMDISMAP1 $D Disable Mapping Register 1
Table 4-14 Quad Timer D Registers Address Map (Continued)
(TMRD_BASE = $00 F100)
Quad Timer D is NOT available in the 56F8145 device
Register Acronym Address Offset Register Description
Peripheral Memory Mapped Registers
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 57
Preliminary
PWMA_PMDISMAP2 $E Disable Mapping Register 2
PWMA_PMCFG $F Configure Register
PWMA_PMCCR $10 Channel Control Register
PWMA_PMPORT $11 Port Register
PWMA_PMICCR $12 PWM Internal Correction Control Register
Table 4-16 Pulse Width Modulator B Registers Address Map
(PWMB_BASE = $00 F160)
Register Acronym Address Offset Register Description
PWMB_PMCTL $0 Control Register
PWMB_PMFCTL $1 Fault Control Register
PWMB_PMFSA $2 Fault Status Acknowledge Register
PWMB_PMOUT $3 Output Con trol Register
PWMB_PMCNT $4 Counter Register
PWMB_PWMCM $5 Counter Modulo Register
PWMB_PWMVAL0 $6 Value Register 0
PWMB_PWMVAL1 $7 Value Register 1
PWMB_PWMVAL2 $8 Value Register 2
PWMB_PWMVAL3 $9 Value Register 3
PWMB_PWMVAL4 $A Value Register 4
PWMB_PWMVAL5 $B Value Register 5
PWMB_PMDEADTM $C Dead Time Register
PWMB_PMDISMAP1 $D Disable Mapping Register 1
PWMB_PMDISMAP2 $E Disable Mapping Register 2
PWMB_PMCFG $F Configure Register
PWMB_PMCCR $10 Channel Control Register
PWMB_PMPORT $11 Port Register
PWMB_PMICCR $12 PWM Internal Correction Control Register
Table 4-15 Pulse Width Modulator A Registers Address Map (Continued)
(PWMA_BASE = $00 F140)
PWMA is NOT available in the 56F8145 device
Register Acronym Address Offset Register Description
56F8345 Technical Data, Rev. 17
58 Freescale Semiconductor
Preliminary
Table 4-17 Quadrature Decoder 0 Registers Address Map
(DEC0_BASE = $00 F180)
Register Acronym Address Offset Register Description
DEC0_DECCR $0 Decoder Control Register
DEC0_FIR $1 Filter Interval Register
DEC0_WTR $2 Watchdog Time-out Register
DEC0_POSD $3 Position Difference Counter Register
DEC0_POSDH $4 Position Difference Counter Hold Register
DEC0_REV $5 Revolution Counter Register
DEC0_REVH $6 Revolution Hold Register
DEC0_UPOS $7 Upper Position Counter Register
DEC0_LPOS $8 Lower Position Counter Register
DEC0_UPOSH $9 Upper Position Hold Register
DEC0_LPOSH $A Lower Position Hold Register
DEC0_UIR $B Upper Initialization Register
DEC0_LIR $C Lower Initialization Register
DEC0_IMR $D Input Monitor Register
Table 4-18 Quadrature Decoder 1 Registers Address Map
(DEC1_BASE = $00 F190)
Quadrature Decoder 1 is NOT available in the 56F8145 device
Register Acronym Address Offset Register Description
DEC1_DECCR $0 Decoder Control Register
DEC1_FIR $1 Filter Interval Register
DEC1_WTR $2 Watchdog Time-out Register
DEC1_POSD $3 Position Difference Counter Register
DEC1_POSDH $4 Position Difference Counter Hold Register
DEC1_REV $5 Revolution Counter Register
DEC1_REVH $6 Revolution Hold Register
DEC1_UPOS $7 Upper Positio n Counter Register
DEC1_LPOS $8 Lower Position Counter Registe r
DEC1_UPOSH $9 Upper Position Hold Register
DEC1_LPOSH $A Lower Position Hold Register
DEC1_UIR $B Upper Initialization Register
DEC1_LIR $C Lower Initialization Register
Peripheral Memory Mapped Registers
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 59
Preliminary
DEC1_IMR $D Input Monitor Register
Table 4-19 Interrupt Control Registers Address Map
(ITCN_BASE = $00 F1A0)
Register Acronym Address Offset Register Description
IPR 0 $0 Interrupt Priority Register 0
IPR 1 $1 Interrupt Priority Register 1
IPR 2 $2 Interrupt Priority Register 2
IPR 3 $3 Interrupt Priority Register 3
IPR 4 $4 Interrupt Priority Register 4
IPR 5 $5 Interrupt Priority Register 5
IPR 6 $6 Interrupt Priority Register 6
IPR 7 $7 Interrupt Priority Register 7
IPR 8 $8 Interrupt Priority Register 8
IPR 9 $9 Interrupt Priority Register 9
VBA $A Vector Base Address Register
FIM0 $B Fast Interrupt Match Register 0
FIVAL0 $C Fast Interrupt Vector Address Low 0 Register
FIVAH0 $D Fast Interrupt Vector Address High 0 Register
FIM1 $E Fast Interrupt Match Register 1
FIVAL1 $F Fast Interrupt Vector Address Low 1 Register
FIVAH1 $10 Fast Interrupt Vector Address High 1 Register
IRQP 0 $11 IRQ Pending Register 0
IRQP 1 $12 IRQ Pending Register 1
IRQP 2 $13 IRQ Pending Register 2
IRQP 3 $14 IRQ Pending Register 3
IRQP 4 $15 IRQ Pending Register 4
IRQP 5 $16 IRQ Pending Register 5
Reserved
ICTL $1D Interrupt Control Register
Table 4-18 Quadrature Decoder 1 Registers Address Map (Continued)
(DEC1_BASE = $00 F190)
Quadrature Decoder 1 is NOT available in the 56F8145 device
Register Acronym Address Offset Register Description
56F8345 Technical Data, Rev. 17
60 Freescale Semiconductor
Preliminary
Table 4-20 Analog-to-Digital Converter Registers Address Map
(ADCA_BASE = $00 F200)
Register Acronym Address Offset Register Description
ADCA_CR1 $0 Control Register 1
ADCA_CR2 $1 Control Register 2
ADCA_ZCC $2 Zero Crossing Control Register
ADCA_LST 1 $3 Ch annel List Register 1
ADCA_LST 2 $4 Ch annel List Register 2
ADCA_SDIS $5 Sample Disable Register
ADCA_STAT $6 Status Register
ADCA_LSTAT $7 Limit Status Register
ADCA_ZCSTAT $8 Zero Crossing Status Register
ADCA_RSLT 0 $9 Res ult Register 0
ADCA_RSLT 1 $A Result Register 1
ADCA_RSLT 2 $B Result Register 2
ADCA_RSLT 3 $C Re s ult Register 3
ADCA_RSLT 4 $D Re s ult Register 4
ADCA_RSLT 5 $E Result Register 5
ADCA_RSLT 6 $F Result Register 6
ADCA_RSLT 7 $10 Result Register 7
ADCA_LLMT 0 $11 Low Limit Register 0
ADCA_LLMT 1 $12 Low Limit Register 1
ADCA_LLMT 2 $13 Low Limit Register 2
ADCA_LLMT 3 $14 Low Limit Register 3
ADCA_LLMT 4 $15 Low Limit Register 4
ADCA_LLMT 5 $16 Low Limit Register 5
ADCA_LLMT 6 $17 Low Limit Register 6
ADCA_LLMT 7 $18 Low Limit Register 7
ADCA_HLMT 0 $19 High Limit Register 0
ADCA_HLMT 1 $1A High Limit Register 1
ADCA_HLMT 2 $1B High Limit Register 2
ADCA_HLMT 3 $1C High Limit Register 3
ADCA_HLMT 4 $1D High Limit Register 4
ADCA_HLMT 5 $1E High Limit Register 5
ADCA_HLMT 6 $1F High Limit Register 6
Peripheral Memory Mapped Registers
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 61
Preliminary
ADCA_HLMT 7 $20 High Limit Register 7
ADCA_OFS 0 $21 Offset Register 0
ADCA_OFS 1 $22 Offset Register 1
ADCA_OFS 2 $23 Offset Register 2
ADCA_OFS 3 $24 Offset Register 3
ADCA_OFS 4 $25 Offset Register 4
ADCA_OFS 5 $26 Offset Register 5
ADCA_OFS 6 $27 Offset Register 6
ADCA_OFS 7 $28 Offset Register 7
ADCA_POWER $29 Power Control Register
ADCA_CAL $2A ADC Calibration Register
Table 4-21 Analog-to-Digital Converter Registers Address Map
(ADCB_BASE = $00 F240)
Register Acronym Address Offset Register Description
ADCB_CR1 $0 Control Register 1
ADCB_CR2 $1 Control Register 2
ADCB_ZCC $2 Zero Crossing Control Register
ADCB_LST 1 $3 Ch annel List Register 1
ADCB_LST 2 $4 Ch annel List Register 2
ADCB_SDIS $5 Sample Disable Register
ADCB_STAT $6 Status Register
ADCB_LSTAT $7 Limit Status Register
ADCB_ZCSTAT $8 Zero Crossing Status Register
ADCB_RSLT 0 $9 Res ult Register 0
ADCB_RSLT 1 $A Result Register 1
ADCB_RSLT 2 $B Result Register 2
ADCB_RSLT 3 $C Re s ult Register 3
ADCB_RSLT 4 $D Re s ult Register 4
ADCB_RSLT 5 $E Result Register 5
ADCB_RSLT 6 $F Result Register 6
ADCB_RSLT 7 $10 Result Register 7
ADCB_LLMT 0 $11 Low Limit Register 0
Table 4-20 Analog-to-Digital Converter Registers Address Map (Continued)
(ADCA_BASE = $00 F200)
Register Acronym Address Offset Register Description
56F8345 Technical Data, Rev. 17
62 Freescale Semiconductor
Preliminary
ADCB_LLMT 1 $12 Low Limit Register 1
ADCB_LLMT 2 $13 Low Limit Register 2
ADCB_LLMT 3 $14 Low Limit Register 3
ADCB_LLMT 4 $15 Low Limit Register 4
ADCB_LLMT 5 $16 Low Limit Register 5
ADCB_LLMT 6 $17 Low Limit Register 6
ADCB_LLMT 7 $18 Low Limit Register 7
ADCB_HLMT 0 $19 High Limit Register 0
ADCB_HLMT 1 $1A High Limit Register 1
ADCB_HLMT 2 $1B High Limit Register 2
ADCB_HLMT 3 $1C High Limit Register 3
ADCB_HLMT 4 $1D High Limit Register 4
ADCB_HLMT 5 $1E High Limit Register 5
ADCB_HLMT 6 $1F High Limit Register 6
ADCB_HLMT 7 $20 High Limit Register 7
ADCB_OFS 0 $21 Offset Register 0
ADCB_OFS 1 $22 Offset Register 1
ADCB_OFS 2 $23 Offset Register 2
ADCB_OFS 3 $24 Offset Register 3
ADCB_OFS 4 $25 Offset Register 4
ADCB_OFS 5 $26 Offset Register 5
ADCB_OFS 6 $27 Offset Register 6
ADCB_OFS 7 $28 Offset Register 7
ADCB_POWER $29 Power Control Register
ADCB_CAL $2A ADC Calibration Register
Table 4-22 Temperature Sensor Register Address Map
(TSENSOR_BASE = $00 F270)
Temperature Sensor is NOT available in the 56F8145 device
Register Acronym Address Offset Register Description
TSENSOR_CNTL $0 Control Register
Table 4-21 Analog-to-Digital Converter Registers Address Map (Continued)
(ADCB_BASE = $00 F240)
Register Acronym Address Offset Register Description
Peripheral Memory Mapped Registers
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 63
Preliminary
Table 4-23 Serial Communication Interface 0 Registers Address Map
(SCI0_BASE = $00 F280)
Register Acronym Address Offset Register Description
SCI0_SCIBR $0 Baud Rate Register
SCI0_SCICR $1 Control Register
Reserved
SCI0_SCISR $3 Status Register
SCI0_SCIDR $4 Data Register
Table 4-24 Serial Communication Interface 1 Registers Address Map
(SCI1_BASE = $00 F290)
Register Acronym Address Offset Register Description
SCI1_SCIBR $0 Baud Rate Register
SCI1_SCICR $1 Control Register
Reserved
SCI1_SCISR $3 Status Register
SCI1_SCIDR $4 Data Register
Table 4-25 Serial Peripheral Interface 0 Registers Address Map
(SPI0_BASE = $00 F2A0)
Register Acronym Address Offset Register Description
SPI0_SPSCR $0 Status and Control Register
SPI0_SPDSR $1 Data Size Register
SPI0_SPDRR $2 Data Receive Register
SPI0_SPDTR $3 Data Transmitter Register
Table 4-26 Serial Peripheral Interface 1 Registers Address Map
(SPI1_BASE = $00 F2B0)
Register Acronym Address Offset Register Description
SPI1_SPSCR $0 Status and Control Register
SPI1_SPDSR $1 Data Size Register
SPI1_SPDRR $2 Data Receive Register
56F8345 Technical Data, Rev. 17
64 Freescale Semiconductor
Preliminary
SPI1_SPDTR $3 Data Transmitter Register
Table 4-27 Computer Operating Properly Registers Address Map
(COP_BASE = $00 F2C0)
Register Acronym Address Offset Register Description
COPCTL $0 Control Register
COPTO $1 Time-Out Register
COPCTR $2 Counter Register
Table 4-28 Clock Generation Module Registers Address Map
(CLKGEN_BASE = $00 F2D0)
Register Acronym Address Offset Register Description
PLLCR $0 Control Register
PLLDB $1 Divide-By Register
PLLSR $2 Status Register
Reserved
SHUTDOWN $4 Shutdown Register
OSCTL $5 Oscillator Control Register
Table 4-29 GPIOA Re gisters Address Map
(GPIOA_BASE = $00 F2E0)
Register Acronym Address Offset Register Description Reset Value
GPIOA_PUR $0 Pull-up Enable Register 0 x 3FFF
GPIOA_DR $1 Data Register 0 x 0000
GPIOA_DDR $2 Data Direction Register 0 x 0000
GPIOA_PER $3 Peripheral Enable Registe r 0 x 3FFF
GPIOA_IAR $4 Interrupt Assert Register 0 x 0000
GPIOA_IENR $5 Interrupt Enable Register 0 x 0000
GPIOA_IPOLR $6 Interru pt Polarity Register 0 x 0000
GPIOA_IPR $7 Interrupt Pending Register 0 x 0000
GPIOA_IESR $8 Interrupt Edge-Sensitive Register 0 x 0000
Table 4-26 Serial Peripheral Interface 1 Registers Address Map (Continued)
(SPI1_BASE = $00 F2B0)
Register Acronym Address Offset Register Description
Peripheral Memory Mapped Registers
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 65
Preliminary
GPIOA_PPMODE $9 Push-Pull Mode Register 0 x 3FFF
GPIOA_RAWDATA $A Raw Data Input Register —
Table 4-30 GPIOB Re gisters Address Map
(GPIOB_BASE = $00 F300)
Register Acronym Address Offset Register Description Reset Value
GPIOB_PUR $0 Pull-up Enable Register 0 x 00FF
GPIOB_DR $1 Data Register 0 x 0000
GPIOB_DDR $2 Data Direction Register 0 x 0000
GPIOB_PER $3 Periphera l Enable Register 0 x 0000
GPIOB_IAR $4 Interrupt Assert Register 0 x 0000
GPIOB_IENR $5 Interrupt Enable Register 0 x 0000
GPIOB_IPOLR $6 Interrup t Pola rity Register 0 x 0000
GPIOB_IPR $7 Interrupt Pending Register 0 x 0000
GPIOB_IESR $8 Interrupt Edge-Sensitive Register 0 x 0000
GPIOB_PPMODE $9 Push-Pull Mode Register 0 x 00FF
GPIOB_RAWDATA $A Raw Data Input Register —
Table 4-31 GPIOC Re gisters Address Map
(GPIOC_BASE = $00 F310)
Register Acronym Address Offset Register Description Reset Value
GPIOC_PUR $0 Pull-up Enable Register 0 x 07FF
GPIOC_DR $1 Data Register 0 x 0000
GPIOC_DDR $2 Data Dire ction Register 0 x 0000
GPIOC_PER $3 Peripheral Enable Register 0 x 07FF
GPIOC_IAR $4 Interrupt Assert Register 0 x 0000
GPIOC_IENR $5 Interrupt Enable Register 0 x 0000
GPIOC_IPOLR $ 6 Interrupt Polarity Register 0 x 0000
GPIOC_IPR $7 Interrupt Pending Register 0 x 0000
GPIOC_IESR $8 Interrupt Edge-Sen sitive Register 0 x 0000
GPIOC_PPMODE $9 Push-Pull Mode Register 0 x 07FF
Table 4-29 GPIOA Registers Address Map (Continued)
(GPIOA_BASE = $00 F2E0)
Register Acronym Address Offset Register Description Reset Value
56F8345 Technical Data, Rev. 17
66 Freescale Semiconductor
Preliminary
GPIOC_RAWDATA $A Raw Data Input Register —
Table 4-32 GPIOD Re gisters Address Map
(GPIOD_BASE = $00 F320)
Register Acronym Address Offset Register Description Reset Value
GPIOD_PUR $0 Pull-up Enable Register 0 x 1FFF
GPIOD_DR $1 Data Register 0 x 0000
GPIOD_DDR $2 Data Direction Register 0 x 0000
GPIOD_PER $3 Peripheral Enable Register 0 x 1FC0
GPIOD_IAR $4 Interrupt Assert Register 0 x 0000
GPIOD_IENR $5 Interrupt Enable Register 0 x 0000
GPIOD_IPOLR $6 Interru pt Polarity Register 0 x 0000
GPIOD_IPR $7 Interrupt Pending Register 0 x 0000
GPIOD_IESR $8 Interrupt Edge-Sensitive Re gister 0 x 0000
GPIOD_PPMODE $9 Push-Pull Mode Register 0 x 1FFF
GPIOD_RAWDATA $A Raw Data Input Register —
Table 4-33 GPIOE Registers Address Map
(GPIOE_BASE = $00 F330)
Register Acronym Address Offset Register Description Reset Value
GPIOE_PUR $0 Pull-up Enable Registe r 0 x 3FFF
GPIOE_DR $ 1 Da ta Register 0 x 0000
GPIOE_DDR $2 Data Direction Register 0 x 0000
GPIOE_PER $3 Peripheral Enable Register 0 x 3FFF
GPIOE_IAR $4 Interrupt Assert Register 0 x 0000
GPIOE_IENR $5 Interrupt Enable Register 0 x 0000
GPIOE_IPOLR $6 I nterrupt Polarity Register 0 x 0000
GPIOE_IPR $7 Interrupt Pending Register 0 x 0000
GPIOE_IESR $8 Interrupt Edge-Sen s itive Register 0 x 0000
GPIOE_PPMODE $9 Push-Pull Mode Reg ister 0 x 3FFF
GPIOE_RAWDATA $A Raw Data Input Register —
Table 4-31 GPIOC Registers Address Map (Continued)
(GPIOC_BASE = $00 F310)
Register Acronym Address Offset Register Description Reset Value
Peripheral Memory Mapped Registers
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 67
Preliminary
Table 4-34 GPIOF Registers Address Map
(GPIOF_BASE = $00 F340)
Register Acronym Address Offset Register Description Reset Value
GPIOF_PUR $0 Pull-up Enable Register 0 x FFFF
GPIOF_DR $1 Data Register 0 x 0000
GPIOF_DDR $2 Data Direction Register 0 x 0000
GPIOF_PER $3 Peripheral Enable Register 0 x FFFF
GPIOF_IAR $4 Interrupt Assert Register 0 x 0000
GPIOF_IENR $5 Interrupt Enable Register 0 x 0000
GPIOF_IPOLR $6 I nterrupt Polarity Register 0 x 0000
GPIOF_IPR $7 Interrupt Pending Register 0 x 0000
GPIOF_IESR $8 Interrupt Edge-Sensitive Register 0 x 0000
GPIOF_PPMODE $9 Push-Pull Mode Register 0 x FFFF
GPIOF_RAWDATA $A Raw Data Input Register —
Table 4-35 System Integration Module Registers Address Map
(SIM_BASE = $00 F350)
Register Acronym Address Offset Register De scription
SIM_CONTROL $0 Control Register
SIM_RSTSTS $1 Reset Status Register
SIM_SCR0 $2 Software Control Register 0
SIM_SCR1 $3 Software Control Register 1
SIM_SCR2 $4 Software Control Register 2
SIM_SCR3 $5 Software Control Register 3
SIM_MSH_ID $6 Most Sign ificant Half JTAG ID
SIM_LSH_ID $7 Least Significant Half JTAG ID
SIM_PUDR $8 Pull-up Disable Register
Reserved
SIM_CLKOSR $A Clock Out Select Register
SIM_GPS $B Quad Decoder 1 / Timer B / SPI 1 Select Register
SIM_PCE $C Peripheral Clock Enable Register
SIM_ISALH $ D I/O Short Address Location High Register
SIM_ISALL $E I/O Short Address Loca ti on Low Register
56F8345 Technical Data, Rev. 17
68 Freescale Semiconductor
Preliminary
Table 4-36 Power Supervisor Registers Address Map
(LVI_BASE = $00 F360)
Register Acronym Address Offset Register Description
LVI_CONTROL $0 Control Register
LVI_STATUS $1 Status Register
Table 4-37 Flash Module Registers Address Map
(FM_BASE = $00 F400)
Register Acronym Address Offset Register Description
FMCLKD $0 Clock Divider Register
FMMCR $1 Module Control Register
Reserved
FMSECH $3 Security High Half Register
FMSECL $4 Security Low Half Register
Reserved
Reserved
FMPROT $10 Protection Regi ster (Banked)
FMPROTB $11 Protection Boot Register (Banked)
Reserved
FMUSTAT $13 User Status Register (Banked)
FMCMD $14 Command Register (Banked)
Reserved
Reserved
FMOPT 0 $1A 16-Bit Information Optio n Register 0
Hot temperature ADC reading of Temperature Sensor;
value set during factory test
FMOPT 1 $1B 16-Bit Information Optio n Register 1
Not used
FMOPT 2 $1C 16-Bit Information Option Register 2
Room temperature ADC reading of Temperature Sensor;
value set during factory test
Peripheral Memory Mapped Registers
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 69
Preliminary
Table 4-38 FlexCAN Registers Address Map
(FC_BASE = $00 F800)
FlexCAN is NOT available in the 56F8145 device
Register Acronym Address Offset Register Description
FCMCR $0 M odule Configuration Register
Reserved
FCCTL0 $3 Control Register 0 Register
FCCTL1 $4 Control Register 1 Register
FCTMR $5 Free-Running Timer Register
FCMAXMB $6 Maximum Message Buffer Configuration Register
Reserved
FCRXGMASK_H $8 Receive Global Mask High Register
FCRXGMASK_L $9 Receive Global Mask Low Register
FCRX14MASK_H $A Receive Buffer 14 Mask High Register
FCRX14MASK_L $B Receive Buffer 14 Mask Low Register
FCRX15MASK_H $C Receive Buffer 15 Mask High Register
FCRX15MASK_L $D Receive Buffer 15 Mask Low Register
Reserved
FCSTATUS $10 Error and Status Register
FCIMASK1 $11 Interrupt Masks 1 Register
FCIFLAG1 $12 Interrupt Flags 1 Register
FCR/T_ERROR_CNTRS $13 Receive and Transmit Erro r Counters Register
Reserved
Reserved
Reserved
FCMB0_CONTROL $40 Message Buffer 0 Control / Status Registe r
FCMB0_ID_HIGH $41 Message Buffer 0 ID High Register
FCMB0_ID_LOW $42 Message Bu ffer 0 ID Low Register
FCMB0_DATA $43 Message Buffer 0 Data Register
FCMB0_DATA $44 Message Buffer 0 Data Register
FCMB0_DATA $45 Message Buffer 0 Data Register
FCMB0_DATA $46 Message Buffer 0 Data Register
Reserved
FCMSB1_CONTROL $48 Message Buffer 1 Control / Status Registe r
56F8345 Technical Data, Rev. 17
70 Freescale Semiconductor
Preliminary
FCMSB1_ID_HIGH $49 Message Buffer 1 ID High Register
FCMSB1_ID_LOW $4A Message Bu ffer 1 ID Low Register
FCMB1_DATA $4B Message Buffer 1 Data Register
FCMB1_DATA $4C Message Buffer 1 Data Register
FCMB1_DATA $4D Message Buffer 1 Data Register
FCMB1_DATA $4E Message Buffer 1 Data Register
Reserved
FCMB2_CONTROL $50 Message Buffer 2 Control / Status Registe r
FCMB2_ID_HIGH $51 Message Buffer 2 ID High Register
FCMB2_ID_LOW $52 Message Bu ffer 2 ID Low Register
FCMB2_DATA $53 Message Buffer 2 Data Register
FCMB2_DATA $54 Message Buffer 2 Data Register
FCMB2_DATA $55 Message Buffer 2 Data Register
FCMB2_DATA $56 Message Buffer 2 Data Register
Reserved
FCMB3_CONTROL $58 Message Buffer 3 Control / Status Registe r
FCMB3_ID_HIGH $59 Message Buffer 3 ID High Register
FCMB3_ID_LOW $5A Message Buffer 3 ID Low Register
FCMB3_DATA $5B Message Buffer 3 Data Register
FCMB3_DATA $5C Message Buffer 3 Data Register
FCMB3_DATA $5D Message Buffer 3 Data Register
FCMB3_DATA $5E Message Buffer 3 Data Register
Reserved
FCMB4_CONTROL $60 Message Buffer 4 Control / Status Registe r
FCMB4_ID_HIGH $61 Message Buffer 4 ID High Register
FCMB4_ID_LOW $62 Message Bu ffer 4 ID Low Register
FCMB4_DATA $63 Message Buffer 4 Data Register
FCMB4_DATA $64 Message Buffer 4 Data Register
FCMB4_DATA $65 Message Buffer 4 Data Register
FCMB4_DATA $66 Message Buffer 4 Data Register
Reserved
Table 4 -38 FlexCAN Registers Address Map (Continued)
(FC_BASE = $00 F800)
FlexCAN is NOT available in the 56F8145 device
Register Acronym Address Offset Register Description
Peripheral Memory Mapped Registers
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 71
Preliminary
FCMB5_CONTROL $68 Message Buffer 5 Control / Status Registe r
FCMB5_ID_HIGH $69 Message Buffer 5 ID High Register
FCMB5_ID_LOW $6A Message Buffer 5 ID Low Register
FCMB5_DATA $6B Message Buffer 5 Data Register
FCMB5_DATA $6C Message Buffer 5 Data Register
FCMB5_DATA $6D Message Buffer 5 Data Register
FCMB5_DATA $6E Message Buffer 5 Data Register
Reserved
FCMB6_CONTROL $70 Message Buffer 6 Control / Status Registe r
FCMB6_ID_HIGH $71 Message Buffer 6 ID High Register
FCMB6_ID_LOW $72 Message Bu ffer 6 ID Low Register
FCMB6_DATA $73 Message Buffer 6 Data Register
FCMB6_DATA $74 Message Buffer 6 Data Register
FCMB6_DATA $75 Message Buffer 6 Data Register
FCMB6_DATA $76 Message Buffer 6 Data Register
Reserved
FCMB7_CONTROL $78 Message Buffer 7 Control / Status Registe r
FCMB7_ID_HIGH $79 Message Buffer 7 ID High Register
FCMB7_ID_LOW $7A Message Buffer 7 ID Low Register
FCMB7_DATA $7B Message Buffer 7 Data Register
FCMB7_DATA $7C Message Buffer 7 Data Register
FCMB7_DATA $7D Message Buffer 7 Data Register
FCMB7_DATA $7E Message Buffer 7 Data Register
Reserved
FCMB8_CONTROL $80 Message Buffer 8 Control / Status Registe r
FCMB8_ID_HIGH $81 Message Buffer 8 ID High Register
FCMB8_ID_LOW $82 Message Bu ffer 8 ID Low Register
FCMB8_DATA $83 Message Buffer 8 Data Register
Table 4 -38 FlexCAN Registers Address Map (Continued)
(FC_BASE = $00 F800)
FlexCAN is NOT available in the 56F8145 device
Register Acronym Address Offset Register Description
56F8345 Technical Data, Rev. 17
72 Freescale Semiconductor
Preliminary
FCMB8_DATA $84 Message Buffer 8 Data Register
FCMB8_DATA $85 Message Buffer 8 Data Register
FCMB8_DATA $86 Message Buffer 8 Data Register
Reserved
FCMB9_CONTROL $88 Message Buffer 9 Control / Status Registe r
FCMB9_ID_HIGH $89 Message Buffer 9 ID High Register
FCMB9_ID_LOW $8A Message Buffer 9 ID Low Register
FCMB9_DATA $8B Message Buffer 9 Data Register
FCMB9_DATA $8C Message Buffer 9 Data Register
FCMB9_DATA $8D Message Buffer 9 Data Register
FCMB9_DATA $8E Message Buffer 9 Data Register
Reserved
FCMB10_CONTROL $90 Message Bu ffer 10 Control / Status Register
FCMB10_ID_HIGH $91 Message Buffer 10 ID High Register
FCMB10_ID_LOW $92 Messag e Buffer 10 ID Low Register
FCMB10_DATA $93 Message Buffer 10 Data Register
FCMB10_DATA $94 Message Buffer 10 Data Register
FCMB10_DATA $95 Message Buffer 10 Data Register
FCMB10_DATA $96 Message Buffer 10 Data Register
Reserved
FCMB11_CONTROL $98 Message Bu ffer 11 Control / Status Register
FCMB11_ID_HIGH $99 Message Buffer 11 ID High Register
FCMB11_ID_LOW $9A Message Buffer 11 ID Low Register
FCMB11_DATA $9B Message Buffer 11 Data Register
FCMB11_DATA $9C Message Buffer 11 Data Register
FCMB11_DATA $9D Message Buffer 11 Data Register
FCMB11_DATA $9E Message Buffer 11 Data Register
Reserved
FCMB12_CONTROL $A0 Message Buffer 12 Control / Status Register
FCMB12_ID_HIGH $A1 Message Buffer 12 ID High Register
FCMB12_ID_LOW $A2 Message Buffer 12 ID Low Register
FCMB12_DATA $A3 Message Buffer 12 Da ta Register
Table 4 -38 FlexCAN Registers Address Map (Continued)
(FC_BASE = $00 F800)
FlexCAN is NOT available in the 56F8145 device
Register Acronym Address Offset Register Description
Factory Programmed Memory
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 73
Preliminary
4.8 Factory Programmed Memory
The Boot Flash memory block is programmed during manufacturing with a default Serial Bootloader
program. The Serial Bootloader application can be used to load a user application into the Program and
FCMB12_DATA $A4 Message Buffer 12 Da ta Register
FCMB12_DATA $A5 Message Buffer 12 Da ta Register
FCMB12_DATA $A6 Message Buffer 12 Da ta Register
Reserved
FCMB13_CONTROL $A8 Message Buffer 13 Control / Status Register
FCMB13_ID_HIGH $A9 Message Buffer 13 ID High Register
FCMB13_ID_LOW $AA Message Buffer 13 ID Low Register
FCMB13_DATA $AB Message Buffer 13 Data Register
FCMB13_DATA $AC Message Buffer 13 Data Register
FCMB13_DATA $AD Message Buffer 13 Data Register
FCMB13_DATA $AE Message Buffer 13 Data Register
Reserved
FCMB14_CONTROL $B0 Message Buffer 14 Control / Status Register
FCMB14_ID_HIGH $B1 Message Buffer 14 ID High Register
FCMB14_ID_LOW $B2 Message Buffer 14 ID Low Register
FCMB14_DATA $B3 Message Buffer 14 Da ta Register
FCMB14_DATA $B4 Message Buffer 14 Da ta Register
FCMB14_DATA $B5 Message Buffer 14 Da ta Register
FCMB14_DATA $B6 Message Buffer 14 Da ta Register
Reserved
FCMB15_CONTROL $B8 Message Buffer 15 Control / Status Register
FCMB15_ID_HIGH $B9 Message Buffer 15 ID High Register
FCMB15_ID_LOW $BA Message Buffer 15 ID Low Register
FCMB15_DATA $BB Message Buffer 15 Data Register
FCMB15_DATA $BC Message Buffer 15 Data Register
FCMB15_DATA $BD Message Buffer 15 Data Register
FCMB15_DATA $BE Message Buffer 15 Data Register
Reserved
Table 4 -38 FlexCAN Registers Address Map (Continued)
(FC_BASE = $00 F800)
FlexCAN is NOT available in the 56F8145 device
Register Acronym Address Offset Register Description
56F8345 Technical Data, Rev. 17
74 Freescale Semiconductor
Preliminary
Data Flash (NOT available in the 56F8145) memories of the device. The 56F83xx SCI/CAN Bootloader
User Manual (MC56F83xxBLUM) provides detailed information on this firmware. An application note,
Production Flash Programming (AN1973), details how the Serial Bootloader program can be used to
perform production Flash programming of the on-board Flash memories as well as other potential
methods.
Like all the Flash memory blocks, the Boot Flash can be erased and programmed by the user. The Serial
Bootloader application is programmed as an aid to the end user , but is not required to be used or maintained
in the Boot Flash memory.
Part 5 Interrupt Controller (ITCN)
5.1 Introduction
The Interrupt Controller (ITCN) module is used to arbitrate between various interrupt requests (IRQs), to
signal to the 56800E core when an interrupt of sufficient priority exists, and to what address to jump in
order to service this interrupt.
5.2 Features
The ITCN module design includes these distinctive features:
• Programmable priority levels for each IRQ
• Two programmable Fast Interrupts
• Notification to SIM module to restart clocks out of Wait and Stop modes
• Drives initial address on the address bus after reset
For further information, see Table 4-5, Interrupt Vector Table Contents.
5.3 Functional Description
The Interrupt Controller is a slave on the IPBus. It contains registers allowing each of the 82 interrupt
sources to be set to one of four priority levels, excluding certain interrupts of fixed priority. Next, all of
the interrupt requests of a given level are priority encoded to determine the lowest numerical value of the
active interrupt requests for that level. Within a given priority level, 0 is the highest priority, while number
81 is the lowest.
5.3.1 Normal Interrupt Handling
Once the ITCN has determined that an interrupt is to be serviced and which interrupt has the highest
priority, an interrupt vector address is generated. Normal interrupt handling concatenates the VBA and the
vector number to determine the vector address. In this way, an offset is generated into the vector table for
each interrupt.
Functional Description
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 75
Preliminary
5.3.2 Interrupt Nesting
Interrupt exceptions may be nested to allow an IRQ of higher priority than the current exception to be
serviced. The following tables define the nesting requirements for each priority level.
5.3.3 Fast Interrupt Handling
Fast interrupts are described in the DSP56F800E Reference Manual. The interrupt controller recognizes
fast interrupts before the core does.
A fast interrupt is defined (to the ITCN) by:
1. Setting the priority of the interrupt as level 2, with the appropriate field in the IPR registers
2. Setting the FIMn register to the appropriate vector number
3. Setting the FIVALn and FIVAHn registers with the address of the code for the fast interrupt
When an interrupt occurs, its vector number is compared with the FIM0 and FIM1 register values. If a
match occurs, and it is a level 2 interrupt, the ITCN handles it as a fast interrupt. The ITCN takes the vector
address from the appropriate FIVALn and FIVAHn registers, instead of generating an address that is an
offset from the VBA.
The core then fetches the instruction from the indicated vector adddress and if it is not a JSR, the core starts
its fast interrupt handling.
Table 5-1 Interrupt Mask Bit Definition
SR[9]1
1. Core status register bits indicating current interrupt mask within the core.
SR[8]1Permitted Exceptions Masked Exceptions
0 0 Priorities 0, 1, 2, 3 None
0 1 Priorities 1, 2, 3 Priority 0
1 0 Priorities 2, 3 Priorities 0, 1
1 1 Priority 3 Priorities 0, 1, 2
Table 5-2. Interrupt Priority Encoding
IPIC_LEVEL[1:0]1
1. See IPIC field definition in Part 5.6.30.2
Current Interrupt
Priority Level Required Nested
Exception Priority
00 No Interrupt or SWILP Priorities 0, 1, 2, 3
01 Priority 0 Priorities 1, 2, 3
10 Priority 1 Priorities 2, 3
11 Priorities 2 or 3 Priority 3
56F8345 Technical Data, Rev. 17
76 Freescale Semiconductor
Preliminary
5.4 Block Diagram
Figure 5-1 Interrupt Controller Block Diagram
5.5 Operating Modes
The ITCN module design contains two major modes of operation:
•Functional Mode
The ITCN is in this mode by default.
•Wait and Stop Modes
During Wait and Stop modes, the system clocks and the 56800E core are turned of f. The ITCN will signal
a pending IRQ to the System Integration Module (SIM) to restart the clocks and service the IRQ. An IRQ
can only wake up the core if the IRQ is enabled prior to entering the Wait or Stop mode. Also, the IRQA
and IRQB signals automatically become low-level sensi tive in these modes, even if the control register bits
are set to make them falling-edge sensitive. This is because there is no clock available to detect the falling
edge.
A peripheral which requires a clock to generate interrupts will not be able to generate interrupts during Stop
mode. The FlexCAN module can wake the device from Stop mode, and a reset will do just that, or IRQA
and IRQB can wake it up.
Priority
Level
2 -> 4
Decode
INT1
Priority
Level
2 -> 4
Decode
INT82
Level 0
82 -> 7
Priority
Encoder
any0
Level 3
82 -> 7
Priority
Encoder
any3
INT
VAB
IPIC
CONTROL
7
7
PIC_EN
IACK
SR[9:8]
Register Descriptions
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 77
Preliminary
5.6 Register Descriptions
A register address is the sum of a base address and an address offset. The base address is defined at the
system level and the address offset is defined at the module level. The ITCN peripheral has 24 registers.
Table 5-3 ITCN Register Summary
(ITCN_BASE = $00F1A0)
Register
Acronym Base Address + Register Name Section Location
IPR0 $0 Interrupt Priority Register 0 5.6.1
IPR1 $1 Interrupt Priority Register 1 5.6.2
IPR2 $2 Interrupt Priority Register 2 5.6.3
IPR3 $3 Interrupt Priority Register 3 5.6.4
IPR4 $4 Interrupt Priority Register 4 5.6.5
IPR5 $5 Interrupt Priority Register 5 5.6.6
IPR6 $6 Interrupt Priority Register 6 5.6.7
IPR7 $7 Interrupt Priority Register 7 5.6.8
IPR8 $8 Interrupt Priority Register 8 5.6.9
IPR9 $9 Interrupt Priority Register 9 5.6.10
VBA $A Vector Base Address Register 5.6.11
FIM0 $B Fast Interrupt 0 Match Register 5.6.12
FIVAL0 $C Fast Interrupt 0 Vector Address Low Register 5.6.13
FIVAH0 $D Fast Interrupt 0 Vector Address High Register 5.6.14
FIM1 $E Fast Interrupt 1 Match Register 5.6.15
FIVAL1 $F Fast Interrupt 1 Vector Address Low Register 5.6.16
FIVAH1 $10 Fast Interrupt 1 Vector Addres s High Register 5.6.17
IRQP0 $11 IRQ Pending Register 0 5.6.18
IRQP1 $12 IRQ Pending Register 1 5.6.19
IRQP2 $13 IRQ Pending Register 2 5.6.20
IRQP3 $14 IRQ Pending Register 3 5.6.21
IRQP4 $15 IRQ Pending Register 4 5.6.22
IRQP5 $16 IRQ Pending Register 5 5.6.23
Reserved
ICTL $1D Interrupt Control Register 5.6.30
56F8345 Technical Data, Rev. 17
78 Freescale Semiconductor
Preliminary
Add.
Offset Register
Name 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
$0 IPR0 R0 0 BKPT_U0 IPL STPCNT IPL 0 0 0 0 0 0 0 0 0 0
W
$1 IPR1 R0 0 0 0 0 0 0 0 0 0 RX_REG IPL TX_REG IPL TRBUF IPL
W
$2 IPR2 RFMCBE IPL FMCC IPL FMERR IPL LOCK IPL LVI IPL 0 0 IRQB IPL IRQA IPL
W
$3 IPR3 RGPIOD
IPL GPIOE
IPL GPIOF
IPL FCMSGBUF IPL FCWKUP IPL FCERR IPL FCBOFF IPL 0 0
W
$4 IPR4 RSPI0_RCV
IPL SPI1_XMIT
IPL SPI1_RCV
IPL 0 0 0 0 GPIOA IPL GPIOB IPL GPIOC IPL
W
$5 IPR5 RDEC1_XIRQ IPL DEC1_HIRQ IPL SCI1_RCV
IPL SCI1_RERR
IPL 0 0 SCI1_TIDL
IPL SCI1_XMIT
IPL SPI0_XMIT
IPL
W
$6 IPR6 RTMRC0 IPL TMRD3 IPL TMRD2 IPL TMRD1 IPL TMRD0 IPL 0 0 DEC0_XIRQ IPL DEC0_HIRQ
IPL
W
$7 IPR7 RTMRA0 IPL TMRB3 IPL TMRB2 IPL TMRB1 IPL TMRB0 IPL TMRC3 IPL TMRC2 IPL TMRC1 IPL
W
$8 IPR8 RSCI0_RCV IPL SCI0_RERR IPL 0 0 SCI0_TIDL IPL SCI0_XMIT IPL TMRA3 IPL TMRA2 IPL TMRA1 IPL
W
$9 IPR9 RPWMA_F IPL PWMB_F IPL PWMA_RL
IPL PWMB_RL IPL ADCA_ZC IPL ABCB_ZC IPL ADCA_CC IPL ADCB_CC IPL
W
$A VBA R0 0 0 VECTOR BASE ADDRESS
W
$B FIM0 R0 0 0 0 0 0 0 0 0 FAST INTERRUPT 0
W
$C FIVAL0 RFAST INTERRUPT 0
VECTOR ADDRESS LOW
W
$D FIVAH0 R0 0 0 0 0 0 0 0 0 0 0 FAST INTERRUPT 0
VECTOR ADDRESS HIGH
W
$E FIM1 R0 0 0 0 0 0 0 0 0 FAST INTERRUPT 1
W
$F FIVAL1 RFAST INTERRUPT 1
VECTOR ADDRESS LOW
W
$10 FIVAH1 R0 0 0 0 0 0 0 0 0 0 0 FAST INTERRUPT 1
VECTOR ADDRESS HIGH
W0 0 0 0 0 0 0 0 0 0 0
$11 IRQP0 RPENDING [16:2] 1
W
$12 IRQP1 RPENDING [32:17]
W
$13 IRQP2 RPENDING [48:33]
W
$14 IRQP3 RPENDING [64:49]
W
$15 IRQP4 RPENDING [80:65]
W
$16 IRQP5 R1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 PEND-
ING
[81]
W
Reserved
$1D ICTL RINT IPIC VAB INT_DIS 1IRQB
STATE IRQA
STATE IRQB
EDG IRQA
EDG
W
= Reserved
Register Descriptions
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 79
Preliminary
Figure 5-2 ITCN Register Map Summary
5.6.1 Interrupt Priority Register 0 (IPR0)
Figure 5-3 Interrupt Priority Register 0 (IPR0)
5.6.1.1 Reserved—Bits 15–14
This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing.
5.6.1.2 EOnCE Breakpoint Unit 0 Interrupt Priority Level (BKPT_U0 IPL)—
Bits13–12
This field is used to set the interrupt priority levels for IRQs. This IRQ is limited to priorities 1 through 3.
It is disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 1
• 10 = IRQ is priority level 2
• 11 = IRQ is priority level 3
5.6.1.3 EOnCE Step Counter Interrupt Priority Level (STPCNT IPL)—
Bits 11–10
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 1 through 3.
It is disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 1
• 10 = IRQ is priority level 2
• 11 = IRQ is priority level 3
5.6.1.4 Reserved—Bits 9–0
This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing.
Base + $0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Read 0 0 BKPT_U0IPL STPCNT IPL 0 0 0 0 0 0 0 0 0 0
Write
RESET 00 0 0 0 0 0000000000
56F8345 Technical Data, Rev. 17
80 Freescale Semiconductor
Preliminary
5.6.2 Interrupt Priority Register 1 (IPR1)
Figure 5-4 Interrupt Priority Register 1 (IPR1)
5.6.2.1 Reserved—Bits 15–6
This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing.
5.6.2.2 EOnCE Receive Register Full Interrupt Priority Level
(RX_REG IPL)—Bits 5–4
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 1 through 3.
It is disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 1
• 10 = IRQ is priority level 2
• 11 = IRQ is priority level 3
5.6.2.3 EOnCE Transmit Register Empty Interrupt Priority Level
(TX_REG IPL)—Bits 3–2
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 1 through 3.
It is disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 1
• 10 = IRQ is priority level 2
• 11 = IRQ is priority level 3
5.6.2.4 EOnCE Trace Buffer Interrupt Priority Level (TRBUF IPL)—
Bits 1–0
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 1 through 3.
It is disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 1
Base + $1 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Read 0 0 0 0 0 0 0 0 0 0 RX_REG IPL TX_REG IPL TRBUF IPL
Write
RESET 0000000000000000
Register Descriptions
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 81
Preliminary
• 10 = IRQ is priority level 2
• 11 = IRQ is priority level 3
5.6.3 Interrupt Priority Register 2 (IPR2)
Figure 5-5 Interrupt Priority Register 2 (IPR2)
5.6.3.1 Flash Memory Command, Data, Address Buffers Empty Interrupt
Priority Level (FMCBE IPL)—Bits 15–14
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
It is disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.3.2 Flash Memory Command Complete Priority Level (FMCC IPL)—
Bits 13–12
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
It is disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.3.3 Flash Memory Erro r Interrupt Priority Level (FMERR IPL)—Bits 11–10
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
It is disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
Base + $2 15 14 13 12 11 10 9876543210
Read FMCBE IPL FMCC IPL FMERR IPL LOCK IPL LVI IPL 0 0 IRQB IPL IRQA IPL
Write
RESET 0000000000000000
56F8345 Technical Data, Rev. 17
82 Freescale Semiconductor
Preliminary
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.3.4 PLL Loss of Lock Interrupt Priority Level (LOCK IPL)—Bits 9–8
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
It is disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.3.5 Low Voltage Detector Interrupt Priority Level (LVI IPL)—Bits 7–6
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
It is disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.3.6 Reserved—Bits 5–4
This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing.
5.6.3.7 External IRQ B Interrupt Priority Level (IRQB IPL)—Bits 3–2
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
It is disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.3.8 External IRQ A Interrupt Priority Level (IRQA IPL)—Bits 1–0
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
It is disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
Register Descriptions
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 83
Preliminary
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.4 Interrupt Priority Register 3 (IPR3)
Figure 5-6 Interrupt Priority Register 3 (IPR3)
5.6.4.1 GPIOD Interrupt Priority Level (GPIOD IPL)—Bits 15–14
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
They are disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.4.2 GPIOE Interrupt Priority Level (GPIOE IPL)—Bits 13–12
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
They are disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.4.3 GPIOF Interrupt Priority Level (GPIOF IPL)—Bits 11–10
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
They are disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.4.4 FlexCAN Message Buffer Interrupt Priority Level (FCMSGBUF IPL)—
Bits 9–8
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
They are disabled by default.
Base + $3 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Read GPIOD
IPL GPIOE
IPL GPIOF
IPL FCMSGBUF IPL FCWKUP IPL FCERR IPL FCBOFF IPL 0 0
Write
RESET 000000 0 0 0 0 0 0 0 0 0 0
56F8345 Technical Data, Rev. 17
84 Freescale Semiconductor
Preliminary
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.4.5 FlexCAN Wake Up Interrupt Priority Level (FCWKUP IPL)—Bits 7–6
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
They are disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.4.6 FlexCAN Error Interrupt Priority Level (FCERR IPL)—Bits 5–4
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
They are disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.4.7 FlexCAN Bus Off Interrupt Priority Level (FCBOFF IPL)—Bits 3–2
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
They are disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.4.8 Reserved—Bits 1–0
This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing.
Register Descriptions
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 85
Preliminary
5.6.5 Interrupt Priority Register 4 (IPR4)
Figure 5-7 Interrupt Priority Register 4 (IPR4)
5.6.5.1 SPI 0 Receiver Full Interrupt Priority Level (SPI0_RCV IPL)—
Bits 15–14
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
They are disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.5.2 SPI 1 Transmit Empty Interrupt Priority Level (SPI1_XMIT IPL)—
Bits 13–12
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
They are disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.5.3 SPI 1 Receiver Full Interrupt Priority Level (SPI1_RCV IPL)—
Bits 11–10
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
They are disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.5.4 Reserved—Bits 9–6
This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing.
Base + $4 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Read SPI0_RCV
IPL SPI1_XMIT
IPL SPI1_RCV
IPL 0 0 0 0 GPIOA
IPL GPIOB
IPL GPIOC
IPL
Write
RESET 0000000000000000
56F8345 Technical Data, Rev. 17
86 Freescale Semiconductor
Preliminary
5.6.5.5 GPIOA Interrupt Priority Level (GPIOA IPL)—Bits 5–4
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
They are disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.5.6 GPIOB Interrupt Priority Level (GPIOB IPL)—Bits 3–2
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
They are disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.5.7 GPIOC Interrupt Priority Level (GPIOC IPL)—Bits 1–0
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
They are disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.6 Interrupt Priority Register 5 (IPR5)
Figure 5-8 Interrupt Priority Register 5 (IPR5)
5.6.6.1 Quadrature Decoder 1 INDEX Pulse Interrupt Priority Level
(DEC1_XIRQ IPL)—Bits 15–14
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
They are disabled by default.
Base + $5 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Read DEC1_XIRQ
IPL DEC1_HIRQ
IPL SCI1_RCV
IPL SCI1_RERR
IPL 0 0 SCI1_TIDL
IPL SCI1_XMIT
IPL SPI0_XMIT
IPL
Write
RESET 0000000 000000000
Register Descriptions
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 87
Preliminary
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.6.2 Quadrature Decoder 1 HOME Signal Transition or Watchdog Timer
Interrupt Priority Level (DEC1_HIRQ IPL)—Bits 13–12
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
They are disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.6.3 SCI 1 Receiver Full Int errupt Priority Level (SCI1_RCV IPL)—
Bits 11–10
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
They are disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.6.4 SCI 1 Receiver Error Interrupt Priority Level (SCI1_RERR IPL)—
Bits 9–8
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
They are disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.6.5 Reserved—Bits 7–6
This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing.
56F8345 Technical Data, Rev. 17
88 Freescale Semiconductor
Preliminary
5.6.6.6 SCI 1 Transmitter Idle I nterrupt Priority Level (SCI1_TIDL IPL)—
Bits 5–4
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
They are disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.6.7 SCI 1 Transmitter Empty Interrupt Priority Level (SCI1_XMIT IPL)—
Bits 3–2
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
They are disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.6.8 SPI 0 Transmitter Empty Interrupt Priority Level (SPI0_XMIT IPL)—
Bits 1–0
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
They are disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.7 Interrupt Priority Register 6 (IPR6)
Figure 5-9 Interrupt Priority Register 6 (IPR6)
Base + $6 15 14 13 12 11 10 9876543210
Read TMRC0
IPL TMRD3
IPL TMRD2
IPL TMRD1
IPL TMRD0
IPL 0 0 DEC0_XIRQ
IPL DEC0_HIRQ
IPL
Write
RESET 0000000000000000
Register Descriptions
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 89
Preliminary
5.6.7.1 Timer C, Channel 0 Interrupt Priority Level (TMRC0 IPL)—
Bits 15–14
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
They are disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.7.2 Timer D, Channel 3 Interrupt Priority Level (TMRD3 IPL)—
Bits 13–12
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
They are disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.7.3 Timer D, Channel 2 Interrupt Priority Level (TMRD2 IPL)—
Bits 11–10
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
They are disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.7.4 Timer D, Channel 1 Interrupt Priority Level (TMRD1 IPL)—
Bits 9–8
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
They are disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.7.5 Timer D, Channel 0 Interrupt Priority Level (TMRD0 IPL)—
Bits 7–6
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
They are disabled by default.
56F8345 Technical Data, Rev. 17
90 Freescale Semiconductor
Preliminary
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.7.6 Reserved—Bits 5–4
This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing.
5.6.7.7 Quadrature Decoder 0, INDEX Pulse Interrupt Priority Level
(DEC0_XIRQ IPL)—Bits 3–2
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
They are disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.7.8 Quadrature Decoder 0, HOME Signal Transition or Watchdog Timer
Interrupt Priority Level (DEC0_HIRQ IPL)—Bits 1–0
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
They are disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.8 Interrupt Priority Register 7 (IPR7)
Figure 5-10 Interrupt Priority Register (IPR7)
5.6.8.1 Timer A, Channel 0 Interrupt Priority Level (TMRA0 IPL)—Bits 15–14
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
They are disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
Base + $7 15 14 13 12 11 10 9876543210
Read TMRA0 IPL TMRB3 IPL TMRB2 IPL TMRB1 IPL TMRB0 IPL TMRC3 IPL TMRC2 IPL TMRC1 IPL
Write
RESET 0000000000000000
Register Descriptions
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 91
Preliminary
5.6.8.2 Timer B, Channel 3 Interrupt Priority Level (TMRB3 IPL)—Bits 13–12
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
They are disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.8.3 Timer B, Channel 2 Interrupt Priority Level (TMRB2 IPL)—Bits 11–10
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
They are disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.8.4 Timer B, Channel 1 Interrupt Priority Level (TM RB1 IPL)—Bits 9–8
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
They are disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.8.5 Timer B, Channel 0 Interrupt Priority Level (TM RB0 IPL)—Bits 7–6
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
They are disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.8.6 Timer C, Channel 3 Interrupt Priority Level (TM RC3 IPL)—Bits 5–4
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
They are disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
56F8345 Technical Data, Rev. 17
92 Freescale Semiconductor
Preliminary
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.8.7 Timer C, Channel 2 Interrupt Priority Level (TM RC2 IPL)—Bits 3–2
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
They are disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.8.8 Timer C, Channel 1 Interrupt Priority Level (TM RC1 IPL)—Bits 1–0
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
They are disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.9 Interrupt Priority Register 8 (IPR8)
Figure 5-11 Interrupt Priority Register 8 (IPR8)
5.6.9.1 SCI0 Receiver Full Interrupt Priority Level (SCI0_RCV IPL)—Bits 15–14
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
They are disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.9.2 SCI0 Receiver Error Interrupt Priority Level (SCI0_RERR IPL)—
Bits 13–12
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
They are disabled by default.
Base + $8 15 14 13 12 11 10 9876543210
Read SCI0_RCV
IPL SCI0_RERR
IPL 0 0 SCI0_TIDL
IPL SCI0_XMIT
IPL TMRA3 IPL TMRA2 IPL TMRA1 IPL
Write
RESET 0000000000000000
Register Descriptions
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 93
Preliminary
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.9.3 Reserved—Bits 11–10
This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing.
5.6.9.4 SCI0 Transmitter Idle Interrupt Priority Level (SCI0_TIDL IPL)—
Bits 9–8
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
They are disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.9.5 SCI0 Transmitter Empty Interrupt Priority Level (SCI0_XMIT IPL)—
Bits 7–6
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
They are disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.9.6 Timer A, Channel 3 Interrupt Priority Level (TM RA3 IPL)—Bits 5–4
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
They are disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.9.7 Timer A, Channel 2 Interrupt Priority Level (TM RA2 IPL)—Bits 3–2
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
They are disabled by default.
56F8345 Technical Data, Rev. 17
94 Freescale Semiconductor
Preliminary
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.9.8 Timer A, Channel 1 Interrupt Priority Level (TM RA1 IPL)—Bits 1–0
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
They are disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.10 Interrupt Priority Register 9 (IPR9)
Figure 5-12 Interrupt Priority Register 9 (IPR9)
5.6.10.1 PWM A Fault Interrupt Priority Level (PWMA_F IPL)—Bits 15–14
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
They are disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.10.2 PWM B Fault Interrupt Priority Level (PWMB_F IPL)—Bits 13–12
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
They are disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
Base + $9 15 14 13 12 11 10 9876543210
Read PWMA_F IPL PWMB_F IPL PWMA_RL
IPL PWMB_RL
IPL ADCA_ZC IPL ABCB_ZC IPL ADCA_CC
IPL ADCB_CC
IPL
Write
RESET 0000000000000000
Register Descriptions
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 95
Preliminary
5.6.10.3 Reload PWM A Interrupt Priority Level (PWMA_RL IPL)—Bits 11–10
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
They are disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.10.4 Reload PWM B Interrupt Priority Level (PWMB_RL IPL)—Bits 9–8
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
They are disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.10.5 ADC A Zero Crossing or Limit Error Interrupt Priority Level
(ADCA_ZC IPL)—Bits 7–6
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
They are disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.10.6 ADC B Zero Crossing Interrupt Priority Level (ADCB_ZC IPL)—
Bits 5–4
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
They are disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.10.7 ADC A Conversion Complete Interrupt Priority Level
(ADCA_CC IPL)—Bits 3–2
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
They are disabled by default.
56F8345 Technical Data, Rev. 17
96 Freescale Semiconductor
Preliminary
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.10.8 ADC B Conversion Complete Interrupt Priority Level
(ADCB_CC IPL)—Bits 1–0
This field is used to set the interrupt priority level for IRQs. This IRQ is limited to priorities 0 through 2.
They are disabled by default.
• 00 = IRQ disabled (defau lt)
• 01 = IRQ is priority level 0
• 10 = IRQ is priority level 1
• 11 = IRQ is priority level 2
5.6.11 Vector Base Address Register (VBA)
Figure 5-13 Vector Base Address Register (VBA)
5.6.11.1 Reserved—Bits 15–13
This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing.
5.6.11.2 Interrupt Vector Base Address (VECTOR BASE ADDRESS)—
Bits 12–0
The contents of this register determine the location of the Vector Address Table. The value in this register
is used as the upper 13 bits of the interrupt Vector Address Bus (VAB[20:0]). The lower eight bits are
determined based upon the highest-priority interrupt. They are then appended onto VBA before presenting
the full interrupt address to the 56800E core; see Part 5.3.1 for details.
5.6.12 Fast Interrupt 0 Match Register (FIM0)
Figure 5-14 Fast Interrupt 0 Match Register (FIM0)
5.6.12.1 Reserved—Bits 15–7
This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing.
Base + $A 15 14 13 12 11 10 9876543210
Read 000 VECTOR BASE ADDRESS
Write
RESET 0000000000000000
Base + $B 15 14 13 12 11 10 9876543210
Read 000000000 FAST INTERRUPT 0
Write
RESET 0000000000000000
Register Descriptions
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 97
Preliminary
5.6.12.2 Fast Interrupt 0 Vector Number (FAST INTERRUPT 0)—Bits 6–0
This value determines which IRQ will be a Fast Interrupt 0. Fast interrupts vector directly to a service
routine based on values in the Fast Interrupt Vector Address registers without having to go to a jump table
first; see Part 5.3.3. IRQs used as fast interrupts must be set to priority level 2. Unexpected results will
occur if a fast interrupt vector is set to any other priority. Fast interrupts automatically become the
highest-priority level 2 interrupt, regardless of their location in the interrupt table, prior to being declared
as fast interrupt. Fast Interrupt 0 has priority over Fast Interrupt 1. To determine the vector number of each
IRQ, refer to Table 4-5.
5.6.13 Fast Interrupt 0 Vector Address Low Register (FIVAL0)
Figure 5-15 Fast Interrupt 0 Vector Address Low Register (FIVAL0)
5.6.13.1 Fast Interrupt 0 Vector Address Low (FIVAL0)—Bits 15–0
The lower 16 bits of the vector address used for Fast Interrupt 0. This register is combined with FIVAH0
to form the 21-bit vector address for Fast Interrupt 0 defined in the FIM0 register.
5.6.14 Fast Interrupt 0 Vector Address High Register (FIVAH0)
Figure 5-16 Fast Interrupt 0 Vector Address High Register (FIVAH0)
5.6.14.1 Reserved—Bits 15–5
This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing.
5.6.14.2 Fast Interrupt 0 Vector Address High (FIVAH0)—Bits 4–0
The upper five bits of the vector address used for Fast Interrupt 0. This register is combined with FIVAL0
to form the 21-bit vector address for Fast Interrupt 0 defined in the FIM0 register.
Base + $C 15 14 13 12 11 10 9876543210
Read FAST INTERRUPT 0
VECTOR ADDRESS LOW
Write
RESET 0000000000000000
Base + $D 15 14 13 12 11 10 9876543210
Read 00000000000 FAST INTERRUPT 0
VECTOR ADDRESS HIGH
Write
RESET 0000000000000000
56F8345 Technical Data, Rev. 17
98 Freescale Semiconductor
Preliminary
5.6.15 Fast Interrupt 1 Match Register (FIM1)
Figure 5-17 Fast Interrupt 1 Match Register (FIM1)
5.6.15.1 Reserved—Bits 15–7
This bit field is reserved or not implemented. It is read as 0, but cannot be modified by writing.
5.6.15.2 Fast Interrupt 1 Vector Number (FAST INTERRUPT 1)—Bits 6–0
This value determines which IRQ will be a Fast Interrupt 1. Fast interrupts vector directly to a service
routine based on values in the Fast Interrupt Vector Address registers without having to go to a jump table
first; see Part 5.3.3. IRQs used as fast interrupts must be set to priority level 2. Unexpected results will
occur if a fast interrupt vector is set to any other priority. Fast interrupts automatically become the
highest-priority level 2 interrupt, regardless of their location in the interrupt table, prior to being declared
as fast interrupt. Fast Interrupt 0 has priority over Fast Interrupt 1. To determine the vector number of each
IRQ, refer to Table 4-5.
5.6.16 Fast Interrupt 1 Vector Address Low Register (FIVAL1)
Figure 5-18 Fast Interrupt 1 Vector Address Low Register (FIVAL1)
5.6.16.1 Fast Interrupt 1 Vector Address Low (FIVAL1)—Bits 15–0
The lower 16 bits of the vector address are used for Fast Interrupt 1. This register is combined with
FIVAH1 to form the 21-bit vector address for Fast Interrupt 1 defined in the FIM1 register.
5.6.17 Fast Interrupt 1 Vector Address High Register (FIVAH1)
Figure 5-19 Fast Interrupt 1 Vector Address High Register (FIVAH1)
5.6.17.1 Reserved—Bits 15–5
This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing.
Base + $E 15 14 13 12 11 10 9876543210
Read 000000000 FAST INTERRUPT 1
Write
RESET 0000000000000000
Base + $F 15 14 13 12 11 10 9876543210
Read FAST INTERRUPT 1
VECTOR ADDRESS LOW
Write
RESET 0000000000000000
Base + $10 15 14 13 12 11 10 9876543210
Read 00000000000 FAST INTERRUPT 1
VECTOR ADDRESS HIGH
Write
RESET 0000000000000000
Register Descriptions
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 99
Preliminary
5.6.17.2 Fast Interrupt 1 Vector Address High (FIVAH1)—Bits 4–0
The upper five bits of the vector address are used for Fast Interrupt 1. This register is combined with
FIVAL1 to form the 21-bit vector address for Fast Interrupt 1 defined in the FIM1 register.
5.6.18 IRQ Pending 0 Register (IRQP0)
Figure 5-20 IRQ Pending 0 Register (IRQP0)
5.6.18.1 IRQ Pending (PENDING)—Bits 16–2
This register combines with the other five to represent the pending IRQs for interrupt vector numbers 2
through 81.
• 0 = IRQ pending for this vector number
• 1 = No IRQ pending for this vector number
5.6.18.2 Reserved—Bit 0
This bit is reserved or not implemented. It is read as 1 and cannot be modified by writing.
5.6.19 IRQ Pending 1 Register (IRQP1)
Figure 5-21 IRQ Pending 1 Register (IRQP1)
5.6.19.1 IRQ Pending (PENDING)—Bits 32–17
This register combines with the other five to represent the pending IRQs for interrupt vector numbers 2
through 81.
• 0 = IRQ pending for this vector number
• 1 = No IRQ pending for this vector number
Base + $11 15 14 13 12 11 10 9876543210
Read PENDING [16:2] 1
Write
RESET 1111111111111111
$Base + $12 15 14 13 12 11 10 9876543210
Read PENDING [32:17]
Write
RESET 1111111111111111
56F8345 Technical Data, Rev. 17
100 Freescale Semiconductor
Preliminary
5.6.20 IRQ Pending 2 Register (IRQP2)
Figure 5-22 IRQ Pending 2 Register (IRQP2)
5.6.20.1 IRQ Pending (PENDING)—Bits 48–33
This register combines with the other five to represent the pending IRQs for interrupt vector numbers 2
through 81.
• 0 = IRQ pending for this vector number
• 1 = No IRQ pending for this vector number
5.6.21 IRQ Pending 3 Register (IRQP3)
Figure 5-23 IRQ Pending 3 Register (IRQP3)
5.6.21.1 IRQ Pending (PENDING)—Bits 64–49
This register combines with the other five to represent the pending IRQs for interrupt vector numbers 2
through 81.
• 0 = IRQ pending for this vector number
• 1 = No IRQ pending for this vector number
5.6.22 IRQ Pending 4 Register (IRQP4)
Figure 5-24 IRQ Pending 4 Register (IRQP4)
Base + $13 15 14 13 12 11 10 9876543210
Read PENDING [48:33]
Write
RESET 1111111111111111
Base + $14 15 14 13 12 11 10 9876543210
Read PENDING [64:49]
Write
RESET 1111111111111111
Base + $15 15 14 13 12 11 10 9876543210
Read PENDING [80:65]
Write
RESET 1111111111111111
Register Descriptions
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 101
Preliminary
5.6.22.1 IRQ Pending (PENDING)—Bits 80–65
This register combines with the other five to represent the pending IRQs for interrupt vector numbers 2
through 81.
• 0 = IRQ pending for this vector number
• 1 = No IRQ pending for this vector number
5.6.23 IRQ Pending 5 Register (IRQP5)
Figure 5-25 IRQ Pending Register 5 (IRQP5)
5.6.23.1 Reserved—Bits 96–82
This bit field is reserved or not implemented. The bits are read as 1 and cannot be modified by writing.
5.6.23.2 IRQ Pending (PENDING)—Bit 81
This register combines with the other five to represent the pending IRQs for interrupt vector numbers 2
through 81.
• 0 = IRQ pending for this vector number
• 1 = No IRQ pending for this vector number
5.6.24 Reserved—Base + 17
5.6.25 Reserved—Base + 18
5.6.26 Reserved—Base + 19
5.6.27 Reserved—Base + 1A
5.6.28 Reserved—Base + 1B
5.6.29 Reserved—Base + 1C
Base + $16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Read 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 PEND-
ING
[81]
Write
RESET 111111111111111 1
56F8345 Technical Data, Rev. 17
102 Freescale Semiconductor
Preliminary
5.6.30 ITCN Control Register (ICTL)
Figure 5-26 ITCN Control Register (ICTL)
5.6.30.1 Interrupt (INT)—Bit 15
This read-only bit reflects the state of the interrupt to the 56800E core.
• 0 = No interrupt is being sent to the 56800E core
• 1 = An interrupt is being sent to the 56800E core
5.6.30.2 Interrupt Priority Level (IPIC)—Bits 14–13
These read-only bits reflect the state of the new interrupt priority level bits being presented to the 56800E
core at the time the last IRQ was taken. This field is only updated when the 56800E core jumps to a new
interrupt service routine.
Note: Nested interrupts may cause this field to be updated before the original interrupt service routine can
read it.
• 00 = Required nested exception priority levels are 0, 1, 2, or 3
• 01 = Required nested exception priority levels are 1, 2, or 3
• 10 = Required nested exception priority levels are 2 or 3
• 11 = Required nested exception priority level is 3
5.6.30.3 Vector Number - Vector Address Bus (VAB)—Bits 12–6
This read-only field shows the vector number (VAB[7:1]) used at the time the last IRQ was taken. This
field is only updated when the 56800E core jumps to a new interrupt service routine.
Note: Nested interrupts may cause this field to be updated before the original interrupt service routine can
read it.
5.6.30.4 Interrupt Disable (INT_DIS)—Bit 5
This bit allows all interrupts to be disabled.
• 0 = Normal operation (default)
• 1 = All interrupts disabled
5.6.30.5 Reserved—Bit 4
This bit field is reserved or not implemented. It is read as 1 and cannot be modified by writing.
Base + $1D 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Read INT IPIC VAB INT_DIS 1IRQB STATE IRQA STATE IRQB
EDG IRQA
EDG
Write
RESET 0 0 0 1000000 0 1 1 1 0 0
Resets
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 103
Preliminary
5.6.30.6 IRQB State Pin (IRQB STATE) —Bit 3
This read-only bit reflects the state of the external IRQB pin.
5.6.30.7 IRQA State Pin (IRQA STATE) —Bit 2
This read-only bit reflects the state of the external IRQA pin.
5.6.30.8 IRQB Edge Pin (IRQB Edg)—Bit 1
This bit controls whether the external IRQB interrupt is edge- or level-sensitive. During Stop and Wait
modes, it is automatically level-sensitive.
•0 = IRQB interrupt is a low-level sensitive (default)
•1 = IRQB
interrupt is falling-edge sensitive.
5.6.30.9 IRQA Edge Pin (IRQA Edg)—Bit 0
This bit controls whether the external IRQA interrupt is edge- or level-sensitive. During Stop and Wait
modes, it is automatically level-sensitive.
•0 = IRQA interrupt is a low-level sensitive (default)
•1 = IRQA
interrupt is falling-edge sensitive.
5.7 Resets
5.7.1 Reset Handshake Timing
The ITCN provides the 56800E core with a reset vector address whenever RESET is asserted. The reset
vector will be presented until the second rising clock edge after RESET is released.
5.7.2 ITCN After Reset
After reset, all of the ITCN registers are in their default states. This means all interrupts are disabled except
the core IRQs with fixed priorities:
• Illegal Instruction
• SW Interrupt 3
• HW Stack Overflow
• Misaligned Long Word Ac cess
• SW Interrupt 2
• SW Interrupt 1
• SW Interrupt 0
• SW Interrupt LP
These interrupts are enabled at their fixed priority levels.
56F8345 Technical Data, Rev. 17
104 Freescale Semiconductor
Preliminary
Part 6 System Integration Module (SIM)
6.1 Introduction
The SIM module is a system catchall for the glue logic that ties together the system-on-chip. It controls
distribution of resets and clocks and provides a number of control features. The system integration module
is responsible for the following functions:
• Reset sequencing
• Clock generation & distribution
• Stop/Wait control
• Pull-up enables for selected peripherals
• System status registers
• Registers for software access to the JTAG ID of the chip
• Enforcing Flash security
These are discussed in more detail in the sections that follow.
6.2 Features
The SIM has the following features:
• Flash security feature prevents unauthorized access to code/data contained in on-chip Flash memory
• Power-saving clock gating for peripheral
• Three power modes (Run, Wait, Stop) to control power utilization
— Stop mode shuts down the 56800E core, system clock, peripheral clock, and PLL operation
— Stop mode entry can optionally disable PLL and Oscillator (low power vs. fast restart); must be done
explicitly
— Wait mode shuts down the 56800E core and unne cessary system clock operation
— Run mode supports full part operation
• Controls to enable/disable the 56800E core WAIT and STOP instructions
• Calculates base delay for reset extension based upon POR or RESET operations. Reset delay will be 3 x 32
clocks (phased release of reset) for reset, except for POR, which is 221 clock cycles.
• Controls reset sequencing after reset
• Software-initiated reset
• Four 16-bit registers reset only by a Power-On Reset usable for general-purpose software control
• System Control Re gister
• Registers for software access to the JTAG ID of the chip
Operating Modes
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 105
Preliminary
6.3 Operating Modes
Since the SIM is responsible for distributing clocks and resets across the chip, it must understand the
various chip operating modes and take appropriate action. These are:
•Reset Mode, which has two submodes:
— POR and RESET operation
The 56800E core and all peripherals are reset. This occurs when the internal POR is asserted or the
RESET pin is asserted.
— COP reset and software reset operation
The 56800E core and all peripherals are reset. The MA bit within the OMR is not changed. This allows
the software to determine the boot mode (internal or external boot) to be used on the next reset.
•Run Mode
This is the primary mode of operation for this device. In this mode, the 56800E controls chip operation.
•Debug Mode
The 56800E is controlled via JTAG/EOnCE when in debug mode. All peripherals, except the COP and
PWMs, continue to run. COP is disabled and PWM outputs are optionally switched off to disable an y motor
from being driven; see the PWM chapter in the 56F8300 Peripheral User Manual for details.
•Wait Mode
In Wait mode, the core clock and memory clocks are disabled. Optionally, the COP can be stopped.
Similarly, it is an option to switch off PWM outputs to disable any motor from being driven. All othe r
peripherals continue to run.
•Stop Mode
When in Stop mode, the 56800E core, memory and most peripheral clocks are shut down. Optionally, the
COP and CAN can be stopped. For lowest power consumption in Stop mode, the PLL can be shut down.
This must be done explicitly before entering Stop mode, since there is no automatic mechanism for this. The
CAN (along with any non-gated interrupt) is capable of waking the chip up from Stop mode, but is not fully
functional in Stop mode.
6.4 Operating Mode Register
Figure 6-1 OMR
The reset state for MB and MA will depend on the Flash secured state. See Part 4.2 and Part 7 for detailed
information on how the Operating Mode Register (OMR) MA and MB bits operate in this device. For
additional information on the EX bit, see Part 4.4. For all other bits, see the DSP56F800E Reference
Manual.
Note: The OMR is not a Memory Map register; it is directly accessible in code through the acronym OMR.
Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
NL CM XP SD R SA EX 0MB MA
Type R/W R/W R/W R/W R/W R/W R/W R/W R/W
RESET 00000000000000XX
56F8345 Technical Data, Rev. 17
106 Freescale Semiconductor
Preliminary
6.5 Register Descriptions
Table 6-1 SIM Registers (SIM_BASE = $00 F350)
Address Offset Address Acronym Register Name Section Location
Base + $0 SIM_CONTROL Control Register 6.5.1
Base + $1 SIM_RSTSTS Reset Status Register 6.5.2
Base + $2 SIM_SCR0 Software Control Register 0 6.5.3
Base + $3 SIM_SCR1 Software Control Register 1 6.5.3
Base + $4 SIM_SCR2 Software Control Register 2 6.5.3
Base + $5 SIM_SCR3 Software Control Register 3 6.5.3
Base + $6 SIM_MSH_ID Most Significant Half of JTAG ID 6.5.4
Base + $7 SIM_LSH_ID Least Significant Half of JTAG ID 6.5.5
Base + $8 SIM_PUDR Pull-up Disable Register 6.5.6
Reserved
Base + $A SIM_CLKOSR CLKO Select Register 6.5.7
Base + $B SIM_GPS GPIO Peripheral Select Register 6.5.8
Base + $C SIM_PCE Peripheral Clock Enable Reg ister 6.5.9
Base + $D SIM_ISALH I/O Short Address Location High Register 6.5.10
Base + $E SIM_ISALL I/O Short Address Location Low Register 6.5.10
Register Descriptions
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 107
Preliminary
Figure 6-2 SIM Register Map Summary
6.5.1 SIM Control Register (SIM_CONTROL)
Figure 6-3 SIM Control Register (SIM_CONTROL)
6.5.1.1 Reserved—Bits 15–6
This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing.
6.5.1.2 OnCE Enable (OnCE EBL)—Bit 5
• 0 = OnCE clock to 56800E core enabled when core TAP is enabled
• 1 = OnCE clock to 56800E core is always enabled
Add.
Offset Register
Name 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
$0 SIM_
CONTROL R0 0 0 0 0 0 0 0 0 0 ONCE
EBL0SW
RST STOP_
DISABLE WAIT_
DISABLE
W
$1 SIM_
RSTSTS R0 0 0 0 0 0 0 0 0 0 SWR COPR EXTR POR 0 0
W
$2 SIM_SCR0 RFIELD
W
$3 SIM_SCR1 RFIELD
W
$4 SIM_SCR2 RFIELD
W
$5 SIM_SCR3 RFIELD
W
$6 SIM_MSH_
ID R0 0 0 0 0 0 0 1 1 1 1 1 0 1 0 0
W
$7 SIM_LSH_ID R0 1 0 0 0 0 0 0 0 0 0 1 1 1 0 1
W
$8 SIM_PUDR R0PWMA1 CAN EMI_
MODE RESET IRQ XBOOT PWMB PWMA0 0CTRL 0JTAG 0 0 0
W
Reserved
$A SIM_
CLKOSR R0 0 0 0 0 0 A23 A22 A21 A20 CLKDIS CLKOSEL
W
$B SIM_GPS R0 0 0 0 0 0 0 0 0 0 0 0 C3 C2 C1 C0
W
$C SIM_PCE REMI ADCB ADCA CAN DEC1 DEC 0 TMRD TMRC TMRB TMRA SCI1 SCI0 SPI1 SPI0 PWMB PWMA
W
$D SIM_ISALH R1 1 1 1 1 1 1 1 1 1 1 1 1 1 ISAL[23:22]
W
$E SIM_ISALL R ISAL[21:6]
W
= Reserved
Base + $0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Read 0 0 0 0 0 0 0 0 0 0 ONCE
EBL SW
RST STOP_
DISABLE WAIT_
DISABLE
Write
RESET 0000000000000000
56F8345 Technical Data, Rev. 17
108 Freescale Semiconductor
Preliminary
6.5.1.3 Software Reset (SW RST)—Bit 4
This bit is always read as 0. Writing 1 to this field will cause the part to reset.
6.5.1.4 Stop Disable (STOP_DISABLE)—Bits 3–2
• 00 = Stop mode will be entered when the 56800E core executes a STOP instruction
• 01 = The 56800E STOP instruction will not cause entry into Stop mode; STOP_DISABLE can be
reprogrammed in the future
• 10 = The 56800E STOP instruction will not cause entry into Stop mode; STOP_DISABLE can then only be
changed by resetting the device
• 11 = Same operation as 10
6.5.1.5 Wait Disable (WAIT_DISABLE)—Bits 1–0
• 00 = Wait mode will be entered when the 56800E core executes a WAIT instruction
• 01 = The 56800E WAIT instruction will not cause entry into Wait mode; WAIT_DISABLE can be
reprogrammed in the future
• 10 = The 56800E WAIT instruction will not cause entry into Wait mode; WAIT_DISABLE can then only
be changed by resetting the device
• 11 = Same operation as 10
6.5.2 SIM Reset Status Register (SIM_RSTSTS)
Bits in this register are set upon any system reset and are initialized only by a Power-On Reset (POR). A
reset (other than POR) will only set bits in the register; bits are not cleared. Only software should clear this
register.
Figure 6-4 SIM Reset Status Register (SIM_RSTSTS)
6.5.2.1 Reserved—Bits 15–6
This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing.
6.5.2.2 Software Reset (SWR)—Bit 5
When 1, this bit indicates tha t the previous reset occurred as a res ult of a software reset (write to SW RST
bit in the SIM_CONTROL register). This bit will be cleared by any hardware reset or by software. Writing
a 0 to this bit position will set the bit, while writing a 1 to the bit will clear it.
6.5.2.3 COP Reset (COPR)—Bit 4
When 1, the COPR bit indicates the Computer Operating Properly (COP) timer-generated reset has
occurred. This bit will be cleared by a Power-On Reset or by software. Writing a 0 to this bit position will
Base + $1 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Read 0 0 0 0 0 0 0 0 0 0 SWR COPR EXTR POR 0 0
Write
RESET 0000000000 00
Register Descriptions
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 109
Preliminary
set the bit, while writing a 1 to the bit will clear it.
6.5.2.4 External Reset (EXTR)—Bit 3
If 1, the EXTR bit indicates an external system reset has occurred. This bit will be cleared by a Power-On
Reset or by software. Writing a 0 to this bit position will set the bit, while writing a 1 to the bit position
will clear it. Basically, when the EXTR bit is 1, the previous system reset was caused by the external
RESET pin being asserted low.
6.5.2.5 Power-On Reset (POR)—Bit 2
When 1, the POR bit indicates a Power-On Reset occurred some time in the past. This bit can be cleared
only by software or by another type of reset. Writing a 0 to this bit will set the bit, while writing a 1 to the
bit position will clear the bit. In summary, if the bit is 1, the previous system reset was due to a Power-On
Reset.
6.5.2.6 Reserved—Bits 1–0
This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing.
6.5.3 SIM Software Control Registers (SIM_SCR0, SIM_SCR1, SIM_SCR2,
and SIM_SCR3)
Only SIM_SCR0 is shown in this section. SIM_SCR1, SIM_SCR2, and SIM_SCR3 are identical in
functionality.
Figure 6-5 SIM Software Control Register 0 (SIM_SCR0)
6.5.3.1 Software Control Data 1 (FIELD)—Bits 15–0
This register is reset only by the Power-On Reset (POR). It has no part-specific functionality and is
intended for use by a software developer to contain data that will be unaffected by the other reset sources
(RESET pin, software reset, and COP reset).
6.5.4 Most Significant Half of JTAG ID (SIM_MSH_ID)
This read-only register displays the most significant half of the JTAG ID for the chip. This register reads
$11F4.
Base + $2 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Read FIELD
Write
POR 00 0 0 0 0 00000 0 0000
56F8345 Technical Data, Rev. 17
110 Freescale Semiconductor
Preliminary
Figure 6-6 Most Significant Half of JTAG ID (SIM_MSH_ID)
6.5.5 Least Significant Half of JTAG ID (SIM_LSH_ID)
This read-only register displays the least significant half of the JTAG ID for the chip. This register reads
$401D.
Figure 6-7 Least Significant Half of JTAG ID (SIM_LSH_ID)
6.5.6 SIM Pull-up Disable Register (SIM_PUDR)
Most of the pins on the chip have on-chip pull-up resistors. Pins which can operate as GPIO can have these
resistors disabled via the GPIO function. Non-GPIO pins can have their pull-ups disabled by setting the
appropriate bit in this register. Disabling pull-ups is done on a peripheral-by-peripheral basis (for pins not
muxed with GPIO). Each bit in the register (see Figure 6-8) corresponds to a functional group of pins. See
Table 2-2 to identify which pins can deactivate the internal pull-up resistor.
Figure 6-8 SIM Pull-up Disable Register (SIM_PUDR)
6.5.6.1 Reserved —Bit 15
This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing.
Base + $6 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Read 0 0 0 0 0 0 0 1 1 1 1 1 0 1 0 0
Write
RESET 00 0 0 0 0 01111 1 0100
Base + $7 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Read 0 1 0 0 0 0 0 0 0 0 0 1 1 1 0 1
Write
RESET 01 0 0 0 0 00000 1 1101
Base + $8 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Read 0PWMA1 CAN EMI_
MODE RESET IRQ XBOOT PWMB PWMA0 0CTRL 0JTAG 0 0 0
Write
RESET 0000000 0 00000000
Register Descriptions
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 111
Preliminary
6.5.6.2 PWMA1—Bit 14
This bit controls the pull-up resistors on the FAULTA3 pin.
6.5.6.3 CAN—Bit 13
This bit controls the pull-up resistors on the CAN_RX pin.
6.5.6.4 EMI_MODE—Bit 12
This bit controls the pull-up resistors on the EMI_MODE pin.
Note: In this package, this input pin is double-bonded with the adjacent VSS pin and this bit should be
changed to a 1 in order to reduce power consumption.
6.5.6.5 RESET—Bit 11
This bit controls the pull-up resistors on the RESET pin.
6.5.6.6 IRQ—Bit 10
This bit controls the pull-up resistors on the IRQA and IRQB pins.
6.5.6.7 XBOOT—Bit 9
This bit controls the pull-up resistors on the EXTBOOT pin.
Note: In this package, this input pin is double-bonded with the adjacent VSS pin and this bit should be
changed to a 1 in order to reduce power consumption.
6.5.6.8 PWMB—Bit 8
This bit controls the pull-up resistors on the FAULTB0, FAULTB1, FAULTB2, and FAULTB3 pins.
6.5.6.9 PWMA0—Bit 7
This bit controls the pull-up resistors on the FAULTA0, FAULTA1, and FAULTA2 pins.
6.5.6.10 Reserved—Bit 6
This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing.
6.5.6.11 CTRL—Bit 5
This bit controls the pull-up resistors on the WR and RD pins.
6.5.6.12 Reserved—Bit 4
This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing.
6.5.6.13 JTAG—Bit 3
This bit controls the pull-up resistors on the TRST, TMS and TDI pins.
56F8345 Technical Data, Rev. 17
112 Freescale Semiconductor
Preliminary
6.5.6.14 Reserved—Bit 2–0
This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing.
6.5.7 CLKO Select Register (SIM_CLKOSR)
The CLKO select register can be used to multiplex out any one of the clocks generated inside the clock
generation and SIM modules. The default value is SYS_CLK. This path has been optimized in order to
minimize any delay and clock duty cycle distortion. All other clocks primarily muxed out are for test
purposes only, and are subject to significant phase shift at high frequencies.
The upper four bits of the GPIOB register can function as GPIO, [A23:A20], or as additional clock output
signals. GPIO has priority and is enabled/disabled via the GPIOB_PER. If GPIOB[7:4] are programmed
to operate as peripheral outputs, then the choice between [A23:A20] and additional clock outputs is done
here in the CLKOSR. The default state is for the peripheral function of GPIOB[7:4] to be programmed as
[A23:A20]. This can be changed by altering [A23:A20], as shown in Figure 6-9.
Figure 6-9 CLKO Select Register (SIM_CLKOSR)
6.5.7.1 Reserved—Bits 15–10
This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing.
6.5.7.2 Alternate GPIO_B Peripheral Function for A23 (A23)—Bit 9
• 0 = Peripheral output function of GPIOB[7] is defined to be A[23]
• 1 = Peripheral output function of GPIOB[7] is defined to be the oscillator clock (MSTR_OSC, see
Figure 3-4)
6.5.7.3 Alternate GPIO_B Peripheral Function for A22 (A22)—Bit 8
• 0 = Peripheral output function of GPIOB[6] is defined to be A[22]
• 1 = Peripheral output function of GPIOB[6] is defined to be SYS_CLK2
6.5.7.4 Alternate GPIO_B Peripheral Function for A21 (A21)—Bit 7
• 0 = Peripheral output function of GPIOB[5] is defined to be A[21]
• 1 = Peripheral output function of GPIOB[5] is defined to be SYS_CLK
6.5.7.5 Alternate GPIO_B Peripheral Function for A20 (A20)—Bit 6
• 0 = Peripheral output function of GPIOB[4] is defined to be A[20]
• 1 = Peripheral output function of GPIOB[4] is defined to be the prescaler clock (FREF, see Figure 3-4)
Base + $A 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Read 0 0 0 0 0 0 A23 A22 A21 A20 CLK
DIS CLKOSEL
Write
RESET 00 0 0 0 0 00001 0 0000
Register Descriptions
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 113
Preliminary
6.5.7.6 Clockout Disable (CLKDIS)—Bit 5
• 0 = CLKOUT output is enabled and will output the signal indicated by CLKOSEL
• 1 = CLKOUT is tri-stated
6.5.7.7 CLockout Select (CLKOSEL)—Bits 4–0
Selects clock to be muxed out on the CLKO pin.
• 00000 = SYS_CLK (from OCCS - DEFAULT)
• 00001 = Reserved for factory test—56800E clock
• 00010 = Reserved for factory test—XRAM clock
• 00011 = Reserved for factory test—PFLASH odd clock
• 00100 = Reserved for factory test—PFLASH even clock
• 00101 = Reserved for factory test—BFLASH clock
• 00110 = Reserved for factory test—DFLASH clock
• 00111 = Oscillator output
• 01000 = Fout (from OCCS)
• 01001 = Reserved for factory test—IPB clock
• 01010 = Reserved for factory test—Feedback (from OCCS, this is path to PLL)
• 01011 = Reserved for factory test—Prescaler clock (from OCCS)
• 01100 = Reserved for factory test—Postscaler clock (from OCCS)
• 01101 = Reserved for factory test—SYS_CLK2 (from OCCS)
• 01110 = Reserved for factory test—SYS_CLK_DIV2
• 01111 = Reserved for factory test—SYS_CLK_D
• 10000 = ADCA clock
• 10001 = ADCB clock
6.5.8 GPIO Peripheral Select Register (SIM_GPS)
The GPIO Peripheral Select Register can be used to multiplex out any one of the three alternate peripherals
for GPIOC. The default peripheral is Quad Decoder 1 an d Quad Timer B (NOT available in the 56F8145
device); these peripherals work together.
The four I/O pins associated with GPIOC can function as GPIO, Quad Decoder 1/Quad Timer B, or as
SPI 1 signals. GPIO is not the default and is enabled/disabled via the GPIOC_PER, as shown in
Figure 6-10 and Table 6-2. When GPIOC[3:0] are programmed to operate as peripheral I/O, then the
choice between decoder/timer and SPI inputs/outputs is made in the SIM_GPS and in conjunction with the
Quad Timer Status and Control Registers (SCR). The default state is for the peripheral function of
GPIOC[3:0] to be programmed as decoder functions. This can be changed by altering the appropriate
controls in the indicated registers.
56F8345 Technical Data, Rev. 17
114 Freescale Semiconductor
Preliminary
Figure 6-10 Overall Control of Pads Using SIM_GPS Control
Table 6-2 Control of Pads Using SIM_GPS Control 1
1. This applies to the four pi ns that serve as Quad Decoder / Quad Timer / SPI / GPIOC functions. A separate set of control
bits is used for each pin.
Pin Function
Control Registers
Comments
GPIOC_PER
GPIOC_DTR
SIM_GPS
Quad Timer
SCR Register
OEN bits
GPIO Input 0 0 — —
GPIO Output 0 1 — —
Quad Timer Input /
Quad Decoder
Input 2
2. Reset configuration
1 — 0 0 See the “Switch Matrix for Inputs to the Timer”
table in the 56F8300 Per ip heral User Manual
for the definition of timer inputs based on the
Quad Decoder mode configuration.
Quad Timer
Output / Quad
Decoder Input 3
3. Quad Decoder pins are always inputs and function in conjunction with the Quad Timer pins.
1— 0 1
SPI input 1 — 1 — See SPI controls for determining the direction
of each of the SPI pins.
SPI output 1 — 1 —
GPIOC_PER Register
GPIO Controlled I/O Pad Contro l
SIM_ GPS Register
Quad Timer Contro lled
SPI Controlled
0
1
0
1
Register Descriptions
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 115
Preliminary
Figure 6-11 GPIO Peripheral Select Register (SIM_GPS)
6.5.8.1 Reserved—Bits 15–4
This bit field is reserved or not implemented. It is read as 0 and cannot be modified by writing.
6.5.8.2 GPIOC3 (C3)—Bit 3
This bit selects the alternate function for GPIOC3.
• 0 = HOME1/TB3 (default - see “Switch Matrix Mode” bits of the Quad Decoder DECCR register in the
56F8300 Peripheral User’s Manual)
• 1 = SS1
6.5.8.3 GPIOC2 (C2)—Bit 2
This bit selects the alternate function for GPIOC2.
• 0 = INDEX1/TB2 (default)
•1 = MISO1
6.5.8.4 GPIOC1 (C1)—Bit 1
This bit selects the alternate function for GPIOC1.
• 0 = PHASEB1/TB1 (default)
•1 = MOSI1
6.5.8.5 GPIOC0 (C0)—Bit 0
This bit selects the alternate function for GPIOC0.
• 0 = PHASEA1/TB0 (default)
• 1 = SCLK1
6.5.9 Peripheral Clock Enable Register (SIM_PCE)
The Peripheral Clock Enable register is used to enable or disable clocks to the peripherals as a power
savings feature. The clocks can be individually controlled for each peripheral on the chip.
Base + $B 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Read 0 0 0 0 0 0 0 0 0 0 0 0 C3 C2 C1 C0
Write
RESET 000000000000 0 0 0 0
56F8345 Technical Data, Rev. 17
116 Freescale Semiconductor
Preliminary
Figure 6-12 Peripheral Clock Enable Register (SIM_PCE)
6.5.9.1 External Memory Interface Enable (EMI)—Bit 15
Each bit controls clocks to the indicated peripheral.
• 1 = Clocks are enabled
• 0 = The clock is not provided to the peripheral (the peripheral is disabled)
6.5.9.2 Analog-to-Digital Converter B Enable (ADCB)—Bit 14
Each bit controls clocks to the indicated peripheral.
• 1 = Clocks are enabled
• 0 = The clock is not provided to the peripheral (the peripheral is disabled)
6.5.9.3 Analog-to-Digital Converter A Enable (ADCA)—Bit 13
Each bit controls clocks to the indicated peripheral.
• 1 = Clocks are enabled
• 0 = The clock is not provided to the peripheral (the peripheral is disabled)
6.5.9.4 FlexCAN Enable (CAN)—Bit 12
Each bit controls clocks to the indicated peripheral.
• 1 = Clocks are enabled
• 0 = The clock is not provided to the peripheral (the peripheral is disabled)
6.5.9.5 Decod er 1 Enable (DEC1)—Bit 11
Each bit controls clocks to the indicated peripheral.
• 1 = Clocks are enabled
• 0 = The clock is not provided to the peripheral (the peripheral is disabled)
6.5.9.6 Decod er 0 Enable (DEC0)—Bit 10
Each bit controls clocks to the indicated peripheral.
• 1 = Clocks are enabled
• 0 = The clock is not provided to the peripheral (the peripheral is disabled)
Base + $C 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Read EMI ADCB ADCA CAN DEC1 DEC0 TMRD TMRC TMRB TMRA SCI1 SCI0 SPI1 SPI0 PWMB PWMA
Write
RESET 1111111111111111
Register Descriptions
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 117
Preliminary
6.5.9.7 Q uad Timer D Enable (TMRD)—Bit 9
Each bit controls clocks to the indicated peripheral.
• 1 = Clocks are enabled
• 0 = The clock is not provided to the peripheral (the peripheral is disabled)
6.5.9.8 Q uad Timer C Enable (TMRC)—Bit 8
Each bit controls clocks to the indicated peripheral.
• 1 = Clocks are enabled
• 0 = The clock is not provided to the peripheral (the peripheral is disabled)
6.5.9.9 Q uad Timer B Enable (TMRB)—Bit 7
Each bit controls clocks to the indicated peripheral.
• 1 = Clocks are enabled
• 0 = The clock is not provided to the peripheral (the peripheral is disabled)
6.5.9.10 Quad Timer A Enable (TMRA)— Bit 6
Each bit controls clocks to the indicated peripheral.
• 1 = Clocks are enabled
• 0 = The clock is not provided to the peripheral (the peripheral is disabled)
6.5.9.11 Serial Communications Interface 1 Enable (SCI1)—Bit 5
Each bit controls clocks to the indicated peripheral.
• 1 = Clocks are enabled
• 0 = The clock is not provided to the peripheral (the peripheral is disabled)
6.5.9.12 Serial Communications Interface 0 Enable (SCI0)—Bit 4
Each bit controls clocks to the indicated peripheral.
• 1 = Clocks are enabled
• 0 = The clock is not provided to the peripheral (the peripheral is disabled)
6.5.9.13 Serial Peripheral Interface 1 Enable (SPI1)—Bit 3
Each bit controls clocks to the indicated peripheral.
• 1 = Clocks are enabled
• 0 = The clock is not provided to the peripheral (the peripheral is disabled)
6.5.9.14 Serial Peripheral Interface 0 Enable (SPI0)—Bit 2
Each bit controls clocks to the indicated peripheral.
• 1 = Clocks are enabled
• 0 = The clock is not provided to the peripheral (the peripheral is disabled)
56F8345 Technical Data, Rev. 17
118 Freescale Semiconductor
Preliminary
6.5.9.15 Pulse Width Modulator B Enable (PWMB)—Bit 1
Each bit controls clocks to the indicated peripheral.
• 1 = Clocks are enabled
• 0 = The clock is not provided to the peripheral (the peripheral is disabled)
6.5.9.16 Pulse Width Modulator A Enable (PWMA)—Bit 0
Each bit controls clocks to the indicated peripheral.
• 1 = Clocks are enabled
• 0 = The clock is not provided to the peripheral (the peripheral is disabled)
6.5.10 I/O Short Address Location Register (SIM_ISALH and SIM_ISALL)
The I/O Short Address Location registers are used to specify the memory referenced via the I/O short
address mode. The I/O short address mode allows the instruction to specify the lower six bits of address;
the upper address bits are not directly controllable. This register set allows limited control of the full
address, as shown in Figure 6-13.
Note: If this register is set to something other than the top of memory (EOnCE register space) and the EX bit
in the OMR is set to 1, the JTAG port cannot access the on-chip EOnCE registers, and debug functions
will be affected.
Figure 6-13 I/O Short Address Determination
With this register set, an interrupt driver can set the SIM_ISALL register pair to point to its peripheral
registers and then use the I/O Short addressing mode to reference them. The ISR should restore this register
to its previous contents prior to returning from interrupt.
Note: The default value of this register set points to the EOnCE registers.
Note: The pipeline delay between setting this register set and using short I/O addressing with the new value
is three cycles.
Instruction Portion
“Hard Coded” Address Portion
16 Bits from SIM_ISALL Register
2 Bits from SIM_ISALH Register
Full 24-Bit for Short I/O Address
6 Bits from I/O Short Address Mode Instruction
Clock Generation Overview
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 119
Preliminary
Figure 6-14 I/O Short Address Location High Register (SIM_ISALH)
6.5.10.1 Input/Output Short Address Low (ISAL[23:22])—Bit 1–0
This field represents the upper two address bits of the “hard coded” I/O short address.
Figure 6-15 I/O Short Address Location Low Register (SIM_ISAL)
6.5.10.2 Input/Output Short Address Low (ISAL[21:6])—Bit 15–0
This field represents the lower 16 address bits of the “hard coded” I/O short address.
6.6 Clock Generation Overview
The SIM uses an internal master clock from the OCCS (CLKGEN) module to produce the peripheral and
system (core and memory) clocks. The maximum master clock frequency is 120MHz. Peripheral and
system clocks are generated at half the master clock frequency and therefore at a maximum 60MHz. The
SIM provides power modes (Stop, Wait) and clock enables (SIM_PCE register, CLK_DIS, ONCE_EBL)
to control which clocks are in operation. The OCCS, power modes, and clock enables provide a flexible
means to manage power consumption.
Power utilization can be minimized in several ways. In the OCCS, crystal oscillator, and PLL may be shut
down when not in use. When the PLL is in use, its prescaler and postscaler can be used to limit PLL and
master clock frequency. Power modes permit system and/or peripheral clocks to be disabled when unused.
Clock enables provide the means to disable individual clocks. Some peripherals provide further controls
to disable unused subfunctions. Refer to Part 3 On-Chip Clock Synthesis (OCCS), and the 56F8300
Peripheral User Manual for further details.
6.7 Power-Down Modes Overview
The 56F8345/56F8145 operate in one of three power-down modes, as shown in Table 6-3.
Base + $D 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Read 1 1 1 1 1 1 1 1 1 1 1 1 1 1 ISAL[23:22]
Write
RESET 1111111 11111 1 1 11
Base + $E 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Read ISAL[21:6]
Write
RESET 1111111 11111 1 1 11
56F8345 Technical Data, Rev. 17
120 Freescale Semiconductor
Preliminary
All peripherals, except the COP/watchdog timer, run off the IPBus clock frequency, which is the same as
the main processor frequency in this architecture. The maximum frequency of operation is
SYS_CLK = 60MHz.
6.8 Stop and Wait Mode Disable Function
Figure 6-16 Internal Stop Disable Circuit
The 56800E core contains both STOP and WAIT instructions. Both put the CPU to sleep. For lowest
power consumption in Stop mode, the PLL can be shut down. This must be done explicitly before entering
Stop mode, since there is no automatic mechanism for this. When the PLL is shut down, the 56800E
system clock must be set equal to the oscillator output.
Table 6-3 Clock Operation in Power-Down Modes
Mode Core Clocks Peripheral Clocks Description
Run Active Active Device is fully functional
Wait Core and memory
clocks disabled Active Peripherals are active and can produce interrupts if
they have not been masked off.
Interrupts will cause the core to come out of its
suspended state and resume normal operation.
Typically used for power-conscious ap plications.
Stop System clocks continue to be generated in
the SIM, but most are gated prior to
reaching memory, core and peripherals.
The only possible recoveries from Stop mode are:
1. CAN traffic (1st message will be lost)
2. Non-clocked interrupts
3. COP reset
4. External reset
5. Power-on reset
D-FLOP
DQ
C
D-FLOP
DQ
CR
56800E
STOP_DIS
Permanent
Disable
Reprogrammable
Disable
Clock
Select
Reset
D
Note: Wait disable circuit is similar
Resets
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 121
Preliminary
Some applications require the 56800E STOP and WAIT instructions to be disabled. To disable those
instructions, write to the SIM control register (SIM_CONTROL), described in Part 6.5.1. This procedure
can be on either a permanent or temporary basis. Permanently assigned applications last only until their
next reset.
6.9 Resets
The SIM supports four sources of reset. The two asynchronous sources are the external RESET pin and
the Power-On Reset (POR). The two synchronous sources are the software reset, which is generated within
the SIM itself by writing to the SIM_CONTROL register, and the COP reset.
Reset begins with the assertion of any of the reset sources. Release of reset to various blocks is sequenced
to permit proper operation of the device. A POR reset is first extended for 221 clock cycles to permit
stabilization of the clock source, followed by a 32 clock window in which SIM clocking is initiated. It is
then followed by a 32 clock window in which peripherals are released to implement Flash security, and,
finally, followed by a 32 clock window in which the core is initialized. After completion of the described
reset sequence, application code will begin execution.
Resets may be asserted asynchronously, but are always released internally on a rising edge of the system
clock.
Part 7 Security Features
The 56F8345/56F8145 offer security features intended to prevent unauthorized users from reading the
contents of the Flash Memory (FM) array. The Flash security consists of several hardware interlocks that
block the means by which an unauthorized user could gain access to the Flash array.
However, part of the security must lie with the user’s code. An extrem e example would be user’s code that
dumps the contents of the internal program, as this code would defeat the purpose of security. At the same
time, the user may also wish to put a “backdoor” in his program. As an example, the user downloads a
security key through the SCI, allowing access to a programming routine that updates parameters stored in
another section of the Flash.
7.1 Operation with Security Enabled
Once the user has programmed the Flash with his application code, the device can be secured by
programming the security bytes located in the FM configuration field, which occupies a portion of the FM
array. These non-volatile bytes will keep the part secured through reset and through power-down of the
device. Only two bytes within this field are used to enable or disable security. Refer to the Flash Memory
section in the 56F8300 Peripheral User Manual for the state of the security bytes and the resulting state
of security. When Flash security mode is enabled in accordance with the method described in the Flash
Memory module specification, the device will disable the core EOnCE debug capabilities. Normal
program execution is otherwise unaffected.
56F8345 Technical Data, Rev. 17
122 Freescale Semiconductor
Preliminary
7.2 Flash Access Blocking Mechanisms
The 56F8345/56F8145 have several operating functional and test modes. Effective Flash security must
address operating mode selection and anticipate modes in which the on-chip Flash can be compromised
and read without explicit user permission. Methods to block these are outlined in the next subsections.
7.2.1 Forced Operating Mode Selection
At boot time, the SIM determines in which functional modes the device will operate. These are:
• Unsecured Mode
• Secure Mode (EOnCE disabled)
When Flash security is enabled as described in the Flash Memory module specification, the device will
disable the EOnCE debug interface.
7.2.2 Disabling EOnCE Access
On-chip Flash can be read by issuing commands across the EOnCE port, which is the debug interface for
the 56800E core. The TRST, TCLK, TMS, TDO, and TDI pins comprise a JTAG interface onto which the
EOnCE port functionality is mapped. When the device boots, the chip-level JTAG TAP (Test Access Port)
is active and provides the chip’s boundary scan capability and access to the ID register.
Proper implementation of Flash security requires that no access to the EOnCE port is provided when
security is enabled. The 56800E core has an input which disables reading of internal memory via the
JTAG/EOnCE. The FM sets this input at reset to a value determined by the contents of the FM security
bytes.
7.2.3 Flash Lockout Recovery
If a user inadvertently enables Flash security on the device, a built-in lockout recovery mechanism can be
used to reenable access to the device. This mec hanism co mpletely r eases all on- chip Flash, thus dis abling
Flash security. Access to this recovery mechanism is built into CodeWarrior via an instruction in memory
configuration (.cfg) files. Add, or uncomment the following configuration command:
unlock_flash_on_connect 1
For more information, please see CodeWarrior MC56F83xx/DSP5685x Family Targeting Manual.
Flash Access Blocking Mechanisms
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 123
Preliminary
The LOCKOUT_RECOVERY instruction has an associated 7-bit Data Register (DR) that is used to
control the clock divider circuit within the FM module. This divider, FM_CLKDIV[6:0], is used to control
the period of the clock used for timed events in the FM erase algorithm. This register must be set with
appropriate values before the lockout sequence can begin. Refer to the JTAG section of the 56F8300
Peripheral User Manual for more details on setting this register value.
The value of the JTAG FM_CLKDIV[6:0] will replace the value of the FM register FMCLKD that divides
down the system clock for timed events, as illustrated in Figure 7-1. FM_CLKDIV[6] will map to the
PRDIV8 bit, and FM_CLKDIV[5:0] will map to the DIV[5:0] bits. The combination of PRDIV8 and DIV
must divide the FM input clock down to a frequency of 150kHz-200kHz. The “Writing the FMCLKD
Register” section in the Flash Memory chapter of the 56F8300 Peripheral User Manual gives specific
equations for calculating the correct values.
Figure 7-1 JTAG to FM Connection for Lockout Recovery
Two examples of FM_CLKDIV calculations follow.
SYS_CLK
JTAG
FMCLKD
DIVIDER
7
7
7
2
FM_CLKDIV
FM_ERASE
Flash Memory
clock
input
56F8345 Technical Data, Rev. 17
124 Freescale Semiconductor
Preliminary
EXAMPLE 1: If the system clock is the 8MHz crystal frequency because the PLL has not been set up,
the input clock will be below 12.8MHz, so PRDIV8 = FM_CLKDIV[6] = 0. Using the following equation
yields a DIV value of 19 for a clock of 200kHz, and a DIV value of 20 for a clock of 190kHz. This
translates into an FM_CLKDIV[6:0] value of $13 or $14, respectively.
EXAMPLE 2: In this example, the system clock has been set up with a value of 32MHz, making the FM
input clock 16MHz. Because that is greater than 12.8MHz, PRDIV8 = FM_CLKDIV[6] = 1. Using the
following equation yields a DIV value of 9 for a clock of 200kHz, and a DIV value of 10 for a clock of
181kHz. This translates to an FM_CLKDIV[6:0] value of $49 or $4A, respectively.
Once the LOCKOUT_RECOVERY instruction has been shifted into the instruction register, the clock
divider value must be shifted into the corresponding 7-bit data register. After the data register has been
updated, the user must transition the TAP controller into the RUN-TEST/IDLE state for the lockout
sequence to commence. The controller must remain in this state until the erase sequence has completed.
For details, see the JTAG Section in the 56F8300 Peripheral User Manual.
Note: When the lockout recovery sequence has completed, the user must reset both the JTAG TAP controller
(by asserting TRST) and the device (by asserting external chip reset) to return to normal unsecured
operation.
7.2.4 Product Analysis
The recommended method of unsecuring a programmed device for product analysis of field failures is via
SYS_CLK
(2) )( << (DIV + 1)
150[kHz] 200[kHz]
<< (DIV + 1)
150[kHz] 200[kHz]
SYS_CLK
(2) )(
Introduction
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 125
Preliminary
the backdoor key access. The customer would need to supply Technical Support with the backdoor key
and the protocol to access the backdoor routine in the Flash. Additionally, the KEYEN bit that allows
backdoor key access must be set.
An alternative method for performing analysis on a secured hybrid controller would be to mass-erase and
reprogram the Flash with the original code, but to modify the security bytes.
To insure that a customer does not inadvertently lock himself out of the device during programming, it is
recommended that he program the backdoor access key first, his application code second, and the security
bytes within the FM configuration field last.
Part 8 General Purpose Input/Output (GPIO)
8.1 Introduction
This section is intended to supplement the GPIO information found in the 56F8300 Peripheral User
Manual and contains only chip-specific information. This information supercedes the generic information
in the 56F8300 Peripheral User Manual.
8.2 Memory Maps
The width of the GPIO port defines how many bits are implemented in each of the GPIO registers. Based
on this and the default function of each of the GPIO pins, the reset values of the GPIOx_PUR and
GPIOx_PER registers change from port to port. Tables 4-29 through 4-34 define the actual re set values of
these registers.
8.3 Configuration
There are six GPIO ports defined on the 56F8345/56F8145. The width of each port and the associated
peripheral function is shown in Table 8-1 and Table 8-2. The specific mapping of GPIO port pins is
shown in Table 8-3.
Table 8-1 56F8345 GPIO Ports Configuration
GPIO Port Port
Width
Available
Pins in
56F8345 Peripheral Function Reset Function
A14 6
6 pins - EMI Address pins - Can only be used as GPIO
8 pins - EMI Address pins - Not available in this package EMI Address
N/A
B8 5
5 pins - EMI Address pins - Can only be used as GPIO
3 pins - EMI Address pins - Not available in this package GPIO
N/A
56F8345 Technical Data, Rev. 17
126 Freescale Semiconductor
Preliminary
C11 11
4 pins - DEC1 / TMRB / SPI1
4 pins - DEC0 / TMRA
3 pins - PWMA current sense
DEC1 / TMRB
DEC0 / TMRA
PWMA current
sense
D13 11
2 pins - EMI CSn
4 pins - EMI CSn - Can only be used as GPIO
2 pins - SCI1
2 pins - EMI CSn - Not available in this package
3 pins - PWMB current sense
EMI Chip Selects
EMI Chip Selects
SCI1
N/A
PWMB current
sense
E14 12
2 pins - SCI0
2 pins - EMI Address pins - Not available in this package
4 pins - SPI0
2 pins - TMRC
4 pins - TMRD
SCI0
N/A
SPI0
TMRC
TMRD
F16 4
4 pins - EMI Data - Can only be used as GPIO
12 pins - EMI Data - Not available in this package EMI Data
N/A
Table 8-2 56F8145 GPIO Ports Configuration
GPIO Port Port
Width
Available
Pins in
56F8145 Peripheral Function Reset Function
A14 6
6 pins - EMI Address pins - Can only be used as GPIO
8 pins - EMI Address pins - Not available in this package EMI Address
N/A
B8 5
5 pins - EMI Address pins - Can only be used as GPIO
3 pins - EMI Address pins - Not available in this package GPIO
N/A
C11 11
4 pins - SPI1
4 pins - DEC0 / TMRA
3 pins - Dedicated GPIO
DEC1 / TMRB
DEC0 / TMRA
GPIO
D13 11
6 pins - EMI CSn - Can only be used as GPIO
2 pins - SCI1
2 pins - EMI CSn - Not available in this package
3 pins - PWMB current sense
EMI Chip Selects
SCI1
N/A
PWMB current
sense
E14 12
2 pins - SCI0
2 pins - EMI Address pins - Not available in this package
4 pins - SPI0
2 pins - TMRC
4 pins - Dedicated GPIO
SCI0
N/A
SPI0
TMRC
GPIO
Table 8-1 56F8345 GPIO Ports Configuration
GPIO Port Port
Width
Available
Pins in
56F8345 Peripheral Function Reset Function
Configuration
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 127
Preliminary
F16 4
4 pins - EMI Data - Can only be used as GPIO
12 pins - EMI Data - Not available in this package EMI Data
N/A
Table 8-3 GPIO External Signals Map
Pins in shaded rows are not available in 56F8345 / 56F8145
Pins in italics are NOT available in the 56F8145 device
GPIO Port GPIO Bit Reset Function Functional Signal Package Pin #
GPIOA
0Peripheral A8115
1Peripheral A9116
2Peripheral A10117
3Peripheral A11118
4Peripheral A12119
5Peripheral A13120
6N/A
7 N/A
8 N/A
9 N/A
10 N/A
11 N/A
12 N/A
13 N/A
Table 8-2 56F8145 GPIO Ports Configuration
GPIO Port Port
Width
Available
Pins in
56F8145 Peripheral Function Reset Function
56F8345 Technical Data, Rev. 17
128 Freescale Semiconductor
Preliminary
GPIOB
0GPIO A16127
1GPIO A17128
2GPIO A18129
3GPIO A19130
4 GPIO A20 / Prescaler_clock 31
5N/A
6 N/A
7 N/A
GPIOC
0Peripheral
PHASEA1 / TB0 / SCLK129
1Peripheral
PHASEB1 / TB1 / MOSI1210
2Peripheral
INDEX1 / TB2 / MISO1211
3Peripheral
HOME1 / TB3 / SS1212
4 Peripheral PHASEA0 / TA0 127
5 Peripheral PHASEB0 / TA1 128
6 Peripheral INDEX0 / TA2 1
7 Peripheral HOME0 / TA3 2
8Peripheral ISA0 104
9Peripheral ISA1 105
10 Peripheral ISA2 106
Table 8-3 GPIO External Signals Map (Continued)
Pins in shaded rows are not available in 56F8345 / 56F8145
Pins in italics are NOT available in the 56F8145 device
GPIO Port GPIO Bit Reset Function Functional Signal Package Pin #
Configuration
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 129
Preliminary
GPIOD
0GPIO CS21 42
1GPIO CS3143
2GPIO CS4144
3GPIO CS5145
4GPIO CS6146
5GPIO CS7147
6PeripheralTXD1 40
7PeripheralRXD1 41
8N/A
9 N/A
10 Peripheral ISB0 48
11 Peripheral ISB1 50
12 Peripheral ISB2 51
Table 8-3 GPIO External Signals Map (Continued)
Pins in shaded rows are not available in 56F8345 / 56F8145
Pins in italics are NOT available in the 56F8145 device
GPIO Port GPIO Bit Reset Function Functional Signal Package Pin #
56F8345 Technical Data, Rev. 17
130 Freescale Semiconductor
Preliminary
GPIOE
0PeripheralTXD0 7
1PeripheralRXD0 8
2N/A
3 N/A
4 Peripheral SCLK0 124
5 Peripheral MOSI0 126
6 Peripheral MISO0 125
7 Peripheral SS0 123
8 Peripheral TC0 111
9 Peripheral TC1 113
10 Peripheral TD0 107
11 Peripheral TD1 108
12 Peripheral TD2 109
13 Peripheral TD3 110
Table 8-3 GPIO External Signals Map (Continued)
Pins in shaded rows are not available in 56F8345 / 56F8145
Pins in italics are NOT available in the 56F8145 device
GPIO Port GPIO Bit Reset Function Functional Signal Package Pin #
JTAG Information
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 131
Preliminary
Part 9 Joint Test Action Group (JTAG)
9.1 JTAG Information
Please contact your Freescale marketing representative or authorized distributor for
device/package-specific BSDL information.
Part 10 Specifications
10.1 General Characteristics
The 56F8345/56F8145 are fabricated in high-density CMOS with 5V-tolerant TTL-compatible digital
inputs. The term “5V-tolerant” refers to the capability of an I/O pin, built on a 3.3V-compatible process
technology, to withstand a voltage up to 5.5V without damaging the device. Many systems have a mixture
GPIOF
0Peripheral D7122
1Peripheral D8123
2Peripheral D9124
3Peripheral D10126
4N/A
5 N/A
6 N/A
7 N/A
8 N/A
9 N/A
10 N/A
11 N/A
12 N/A
13 N/A
14 N/A
15 N/A
1. Not useful in reset conf iguration in this package - reconfigure as GPIO
2. See Part 6.5.8 to determine how to select peripherals from this set; DEC1 is the selected peripheral at reset
Table 8-3 GPIO External Signals Map (Continued)
Pins in shaded rows are not available in 56F8345 / 56F8145
Pins in italics are NOT available in the 56F8145 device
GPIO Port GPIO Bit Reset Function Functional Signal Package Pin #
56F8345 Technical Data, Rev. 17
132 Freescale Semiconductor
Preliminary
of devices designed for 3.3V and 5V power supplies. In such systems, a bus may carry both 3.3V- and
5V-compatible I/O voltage levels (a standard 3.3V I/O is designed to receive a maximum voltage of 3.3V
± 10% during normal operation without causing damage). This 5V-tolerant capability therefore offers the
power savings of 3.3V I/O levels combined with the ability to receive 5V levels without damage.
Absolute maximum ratings in Table 10-1 are stress ratings only, and functional operation at the maximum
is not guaranteed. Stress beyond these ratings may affect device reliability or cause permanent damage to
the device.
Note: All specifications meet both Automotive and Industrial requirements unless individual
specifications are listed.
Note: The 56F8145 device is guaranteed to 40MHz and specified to meet Industrial requirements only.
Note: The 56F8145 device is specified to meet Industrial requirements only; CAN is NOT available on the
56F8145 device.
CAUTION
This device contains protective circuitry to guard against damage
due to high static voltage or electrical fields. However, normal
precautions are advised to avoid application of any voltages higher
than maximum-rated voltages to this high-impedance circuit.
Reliability of operation is enhanced if unused inputs are tied to an
appropriate voltage level.
Table 10-1 Absolute Maximum Ratings
(VSS = VSSA_ADC = 0)
Characteristic Symbol Notes Min Max Unit
Supply voltage VDD_IO - 0.3 4.0 V
ADC Supply Voltage VDDA_ADC,
VREFH
VREFH must be less than or
equal to VDDA_ADC
- 0.3 4.0 V
Oscillator / PLL Supply Voltage VDDA_OSC_PLL - 0.3 4.0 V
Internal Logic Core Supply Voltage VDD_CORE OCR_DIS is High - 0.3 3.0 V
Input Voltage (digital) VIN Pin Groups 1, 2, 5, 6, 9, 10 -0.3 6.0 V
Input Voltage (analog) VINA Pin Groups 11, 12, 13 -0.3 4.0 V
Output Voltage VOUT Pin Groups 1, 2, 3, 4, 5, 6, 7, 8 -0.3 4.0
6.01V
Output Voltage (open dra in) VOD Pin Group 4 -0.3 6.0 V
Ambient Temp erature (Automotive) TA-40 125 °C
Ambient Temperature (Industrial) TA-40 105 °C
General Characteristics
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 133
Preliminary
Note: Pins in italics are NOT available in the 56F8145 device.
Pin Group 1: TXD0-1, RXD0-1, SS0, MISO0, MOSI0
Pin Group 2: PHASEA0, PHASEA1, PHASEB0, PHASEB1, INDEX0, INDEX1, HOME0, HOME1, ISB0-2, ISA0-2, TD2-3, TC0-1, TDO,
SCLK0
Pin Group 3: RSTO, TDO
Pin Group 4: CAN_TX
Pin Group 5: D0-15, GPIOD0-5
Pin Group 6: A8-15, GPIOB0-4, TD0-1
Pin Group 7: CLKO
Pin Group 8: PWMA0-5, PWMB0 -5
Pin Group 9: IRQA, IRQB, RESET, EXTB OOT , T RS T,TMS, TDI, CAN_RX, EMI_MODE, FAULTA0-3, FAULTB0-3
Pin Group 10: TCK
Pin Group 11: XTAL, EXTAL
Pin Group 12: ANA0-7, ANB0-7
Pin Group 13: OCR_DIS, CLKMODE
Junction Temperature (Automotive) TJ-40 150 °C
Junction Temperature (Industrial) TJ-40 125 °C
Storage Temperature (Automotive) TSTG -55 150 °C
Storage Temperature (Industrial) TSTG -55 150 °C
1. If corresponding GPIO pin is configured as open drain.
Table 10-1 Absolute Maximum Ratings (Continued)
(VSS = VSSA_ADC = 0)
Characteristic Symbol Notes Min Max Unit
56F8345 Technical Data, Rev. 17
134 Freescale Semiconductor
Preliminary
1. Theta-JA determined on 2s2p test boards is freq uently lower than would be observed in an app lication. Dete rmined on 2s2p ther-
mal test board.
2. Junction to ambient thermal resistance, Theta-JA (RθJA) was simulated to be equivalent to the JEDEC specification JESD51-2
in a horizontal configurati on in natural convection. Theta-JA wa s also simul ated on a thermal t est board with t wo interna l planes
(2s2p, where “s” is the number of signal l ayers and “p” is the number of planes) per JESD51-6 and JESD51-7. Th e correct name
for Theta-JA for forced convection or with the non-single layer boards is Theta-JMA.
3. Junction to case thermal resistance, Theta-JC (RθJC ), was simulated to be equivalent to the measured values using the cold
plate techni que with the cold plate temperature used as the "case" temperat ure. The basi c cold pl ate measurement technique i s
described by MIL-STD 883D, Method 1012.1. This is the correct thermal metric to use to calculate thermal performance when
the package is being used with a heat sink.
4. Thermal Characterizati on Parameter, Ps i-JT (ΨJT ), is the "res istance" from junc tion to reference poi nt thermocouple on t op cen-
ter of case as defined in JESD51-2. ΨJT is a useful value to use to estimate junction temperature in steady-state customer en-
vironments.
5. Junction temperat ure is a function of on-chip power dissipat ion, packag e thermal resistance, mounting site (board) t emperature,
ambient temperature, air flow, power dissipatio n of other components on the board, and board thermal resistance.
6. See Part 12.1 for more det ails on thermal design considerations.
Table 10-2 56F8345/56F8145 ElectroStatic Discharge (ESD) Protection
Characteristic Min Typ Max Unit
ESD for Human Body Model (HBM) 2000 — — V
ESD for Machine Model (MM) 200 — — V
ESD for Charge Device Model (CDM) 500 — — V
Table 10-3 Thermal Characteristics6
Characteristic Comments Symbol Value Unit Notes
128-pin LQFP
Junction to ambient
Natural convection RθJA 50.8 °C/W 2
Junction to ambient (@1m/sec) RθJMA 46.5 °C/W 2
Junction to ambient
Natural convection Four layer board (2s2p) RθJMA
(2s2p) 43.9 °C/W 1,2
Junction to ambient (@1m/sec) Four layer board (2s2p) RθJMA 41.7 °C/W 1,2
Junction to case RθJC 13.9 °C/W 3
Junction to center of case ΨJT 1.2 °C/W 4, 5
I/O pin power dissipation P I/O User-determined W
Power dissipation P D P D = (IDD x VDD + P I/O)W
Maximum allowed PDPDMAX (TJ - TA) / RθJA7W
General Characteristics
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 135
Preliminary
7. TJ = Junction temperature
TA = Ambient temperature
Note: The 56F8145 device is guaranteed to 40MHz and specified to meet Industrial requirements only;
CAN is NOT available on the 56F8145 device.
Note: Total chip source or sin k c urrent cannot exceed 200mA
See Pin Groups listed in Table 10-1
Table 10-4 Recommended Operating Conditions
(VREFLO = 0V, VSS = VSSA_ADC = 0V, VDDA = VDDA_ADC = VDDA_OSC_PLL )
Characteristic Symbol Notes Min Typ Max Unit
Supply voltage VDD_IO 33.3 3.6 V
ADC Supply Voltage VDDA_ADC,
VREFH
VREFH must be less
than or equal to
VDDA_ADC
33.3 3.6 V
Oscillator / PLL Supply Voltage VDDA_OSC
_PLL 33.3 3.6 V
Internal Logic Core Supply Voltage VDD_CORE OCR_DIS is High 2.25 2.5 2.75 V
Device Clock Frequency FSYSCLK 0— 60MHz
Input High Voltage (digital) VIN Pin Gr oups
1, 2, 5, 6, 9, 10 2— 5.5 V
Input High Voltage (analog) VIHA Pin Group 13 2—V
DDA+0.3 V
Input High Voltage (XTAL/EXTAL,
XTAL is not driven by an external clock) VIHC Pin Group 11 VDDA-0.8 — VDDA+0.3 V
Input high voltage (XTAL/EXTAL,
XTAL is driven by an external clock) VIHC Pin Group 11 2—V
DDA+0.3 V
Input Low Voltage VIL Pin Groups
1, 2, 5, 6, 9, 10, 11, 13 -0.3 — .8 V
Output High Source Current
VOH = 2.4V (VOH min.) IOH Pin Groups 1, 2, 3 —— -4 mA
Pin Groups 5, 6, 7 —— -8
Pin Groups 8 —— -12
Output Low Sink Current
VOL = 0.4V (VOL max) IOL Pin Groups 1, 2, 3, 4 —— 4 mA
Pin Groups 5, 6, 7 —— 8
Pin Group 8 —— 12
Ambient Operating Temperature
(Automotive) TA-40 — 125 °C
Ambient Operating Temperature
(Industrial) TA-40 — 105 °C
Flash Enduranc e (Automotive)
(Program Erase Cycles) NFTA = -40°C to 125°C 10,000 — — Cycles
Flash Endurance (Industrial)
(Program Erase Cycles) NFTA = -40°C to 105°C 10,000 — — Cycles
Flash Data Retention (Automotive) TRTJ <= 85°C avg 15 — — Years
56F8345 Technical Data, Rev. 17
136 Freescale Semiconductor
Preliminary
10.2 DC Electrical Characteristics
Note: The 56F8145 device is specified to meet Industrial requirements only; CAN is NOT available on the
56F8145 device.
See Pin Groups listed in Table 10-1
Table 10-5 DC Electrical Characteristics
At Recommended Operating Conditi ons; see Table 10-4
Characteristic Symbol Notes M in Typ M ax Unit Test Conditions
Output High Voltage VOH 2.4 — — VI
OH = IOHmax
Output Low Voltage VOL ——0.4VI
OL = IOLmax
Digital Input Current High
pull-up enabled or disabled IIH Pin Groups
1, 2, 5, 6, 9 —0+/- 2.5μAVIN = 3.0V to 5.5V
Digital Input Current High
with pull-down IIH Pin Group 10 40 80 160 μAVIN = 3.0V to 5.5V
Analog Input Current High IIHA Pin Group 13 —0+/- 2.5μAVIN = VDDA
ADC Input Current High IIHADC Pin Group 12 —0+/- 3.5μAVIN = VDDA
Digital Input Current Low
pull-up enabled IIL Pin Groups
1, 2, 5, 6, 9 -200 -100 -50 μAVIN = 0V
Digital Input Current Low
pull-up disabled IIL Pin Groups
1, 2, 5, 6, 9 —0+/- 2.5μAVIN = 0V
Digital Input Current Low
with pull-down IIL Pin Group 10 —0+/- 2.5μAVIN = 0V
Analog Input Current Low IILA Pin Group 13 —0+/- 2.5μAVIN = 0V
ADC Input Current Low IILADC Pin Group 12 —0+/- 3.5μAVIN = 0V
EXTAL Input Current Low
clock input IEXTAL —0+/- 2.5μAVIN = VDD or 0V
XTAL Input Current Low
clock input IXTAL CLKMODE = High —0+/- 2.5μAVIN = VDDA or 0V
CLKMODE = Low — — 200 μAVIN = VDDA or 0V
Output Current
High Impedance State IOZ Pin Groups
1, 2, 3, 4, 5, 6, 7, 8 —0+/- 2.5μAVOUT = 3.0V to 5.5V or 0V
Schmitt Trigger Input
Hysteresis VHYS Pin Groups
2, 6, 9,10 —0.3— V—
Input Capacitance
(EXTAL/XTAL) CINC —4.5—pF —
Output Capacitance
(EXTAL/XTAL) COUTC —5.5—pF —
Input Capacitance CIN —6—
pF —
Output Capacitance COUT —6—
pF —
RES = (VREFH - VREFLO) X 1
212 m
DC Electrical Characteristics
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 137
Preliminary
Table 10-6 Power-On Reset Low Voltage Parameters
Characteristic Symbol Min Typ Max Units
POR Trip Point POR 1.75 1.8 1.9 V
LVI, 2.5 volt Supply, trip point1
1. When VDD_CORE drops below VEI2.5, an interrupt is generated.
VEI2.5 —2.14— V
LVI, 3.3 volt supply, trip point2
2. When VDD_CORE drops below VEI3.3, an interrupt is generated.
VEI3.3 —2.7— V
Bias Current I bias —110130μA
Table 10-7 Current Consumption per Power Supply Pin (Typical)
On-Chip Regulator Enabled (OCR_DIS = Low)
Mode IDD_IO1
1. No Output Switching
2. Includes Processor Core current supplied by internal voltage regulator
IDD_ADC IDD_OSC_PLL Test Conditions
RUN1_MAC 155mA 50mA 2.5mA • 60MHz Device Clock
• All peripheral clocks are enabled
• All peripherals running
• Continuous MAC instructions with fetches from
Data RAM
• ADC powered on and clocked
Wait3 91mA 65μA2.5mA
• 60MHz Device Clock
• All peripheral clocks are enabled
• ADC powered off
Stop1 5.8mA 0μA155μA• 8MHz Device Clock
• All peripheral clocks are off
• ADC powered off
• PLL powered off
Stop2 5.1mA 0μA145μA• External Clock is off
• All peripheral clocks are off
• ADC powered off
• PLL powered off
56F8345 Technical Data, Rev. 17
138 Freescale Semiconductor
Preliminary
Table 10-8 Current Consumption per Power Supply Pin (Typical)
On-Chip Regulator Disabled (OCR_DIS = High)
Mode IDD_Core IDD_IO1
1. No Output Switching
IDD_ADC IDD_OSC_PLL Test Conditions
RUN1_MAC 150mA 13μA50mA 2.5mA• 60MHz Device Clock
• All peripheral clocks are enabled
• All peripherals running
• Continuous MAC instructions with
fetches from Data RAM
• ADC powered on and clocked
Wait3 86mA 13μA65μA2.5mA
• 60MHz Device Clock
• All peripheral clocks are enabled
• All peripherals running
• ADC powered off
Stop1 800μA13μA0μA155μA• 8MHz Device Clock
• All peripheral clocks are off
• ADC powered off
• PLL powered off
Stop2 100μA13μA0μA145μA• External Clock is off
• All peripheral clocks are off
• ADC powered off
• PLL powered off
Table 10-9. Regulator Parameters
Characteristic Symbol Min Typical Max Unit
Unloaded Output Voltage
(0mA Load) VRNL 2.25 — 2.75 V
Loaded Output Voltage
(200mA load) VRL 2.25 — 2.75 V
Line Regulation @ 250mA load
(VDD33 ranges from 3.0V to 3.6V) VR2.25 — 2.75 V
Short Circuit Current
(output shorted to ground) Iss — — 700 mA
Bias Current I bias —5.8 7mA
Power-down Current Ipd —0 2μA
Short-Circuit Tolerance
(output shorted to ground) TRSC — — 30 minutes
DC Electrical Characteristics
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 139
Preliminary
10.2.1 Temperature Sense
Note: Temperature Sensor is NOT available in the 56F8145 device.
Table 10-10. PLL Parameters
Characteristics Symbol Min Typical Max Unit
PLL Start-up time TPS 0.3 0.5 10 ms
Resonator Start-up time TRS 0.1 0.18 1 ms
Min-Max Period Variation TPV 120 — 200 ps
Peak-to-Peak Jitter TPJ ——175ps
Bias Current IBIAS —1.5 2mA
Quiescent Current, power-down mode IPD —100150μA
Table 10-11 Temperature Sense Parametrics
Characteristics Symbol Min Typical Max Unit
Slope (Gain)1m — 7.762 — mV/°C
Room Trim Temp. 1, 2
1. Includes the ADC conversion of the analog Temperature Sense voltage.
2. The ADC is not calibrated for the conversion of the Temperature Sensor trim value stored in the Flash Memory at
FMOPT0 and FMOPT1.
TRT 24 26 28 °C
Hot Trim Temp. (Industrial)1,2 THT 122 125 128 °C
Hot Trim Temp. (Automotive)1,2 THT 147 150 153 °C
Output Voltage @
VDDA_ADC = 3.3V, TJ =0°C1VTS0 —1.370— V
Supply Voltage VDDA_ADC 3.0 3.3 3.6 V
Supply Current - OFF IDD-OFF ——10 μA
Supply Current - ON IDD-ON ——250 μA
Accuracy3,1 from -40°C to 150°C
Using VTS = mT + VTS0
3. See Application Note, AN1980, for methods to increase accuracy.
TACC -6.7 0 6.7 °C
Resolution4, 5,1
4. Assuming a 12-bit range from 0V to 3.3V.
5. Typical resolution calculated using equation,
RES —0.104— °C / bit
56F8345 Technical Data, Rev. 17
140 Freescale Semiconductor
Preliminary
10.3 AC Electrical Characteristics
Tests are conducted using the input levels specified in Table 10-5. Unless otherwise specified,
propagation delays are measured from the 50% to the 50% point, and rise and fall times are measured
between the 10% and 90% points, as shown in Figure 10-1.
Figure 10-1 Input Signal Measurement References
Figure 10-2 shows the definitions of the following signal states:
• Active state, when a bus or signal is driven, and enters a low impedance state
• Tri-stated, when a bus or signal is placed in a high impedance state
• Data Valid state, when a signal level has reached VOL or VOH
• Data Invalid state, when a signal level is in transition between VOL and VOH
Figure 10-2 Signal States
10.4 Flash Memory Characteristics
Table 10-12 Flash Timing Parameters
Characteristic Symbol Min Typ Max Unit
Program time1
1. There is additi onal overhead which is part of the programming sequence. See the 56F8300 Peripheral User Manual
for details. Program time i s per 16-bit word in Flash memory. Two word s at a time can be programme d within the Pro-
gram Flash module, as it contains two interleaved memories.
Tprog 20 — — μs
Erase time2
2. Specifies page erase time. There are 512 bytes per page in the Data and Boot Flash memories. The Program Flash
module uses two interleaved Flash memories, increasing the effective page size to 1024 bytes.
Terase 20 — — ms
Mass erase time Tme 100 — — ms
VIH
VIL
Fall Time
Input Signal
Note: The midpoint is VIL + (VIH – VIL)/2.
Midpoint1
Low High 90%
50%
10%
Rise Time
Data Inva lid State
Data1
Data2 Valid
Data
Tri-stated
Data3 Valid
Data2 Data3
Data1 Valid
Data Active Data Active
External Clock Operation Timing
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 141
Preliminary
10.5 External Clock Operation Timing
Figure 10-3 External Clock Timing
10.6 Phase Locked Loop Timing
Table 10-13 External Clock Operation Timing Requirements1
1. Parameters listed are guaranteed by design.
Characteristic Symbol Min Typ Max Unit
Frequency of operation (external clock driver)2
2. See Figure 10-3 for details on using the recommended connection of an external clock driver.
fosc 0—120MHz
Clock Pulse Width3
3. The high or low pulse width must be no smaller than 8.0ns or the chip will not function.
tPW 3.0 — — ns
External clock input rise time 4
4. External clock input rise time is measured from 10% to 90%.
trise — — 10 ns
External clock input fall ti me5
5. External clock input fall time is measured from 90% to 10%.
tfall — — 10 ns
Table 10-14 PLL Timing
Characteristic Symbol Min Typ Max Unit
External reference crystal frequency for the PLL1
1. An externally supplied reference clock should be as free as possible from any phase jitter for the PLL to work
correctly. The PLL is optimized for 8MHz input crystal.
fosc 488.4MHz
PLL output frequency2 (fOUT)
2. ZCLK may not exceed 60MHz. For additional information on ZCLK and (fOUT/2), please refer to the OCCS chapter in
the 56F8300 Peripheral User Manual.
fop 160 — 260 MHz
PLL stabilization time3 -40° to +125°Ctplls —110ms
External
Clock
VIH
VIL
Note: The midpoint is VIL + (VIH – VIL)/2.
90%
50%
10%
90%
50%
10%
tPW tPW tfall trise
56F8345 Technical Data, Rev. 17
142 Freescale Semiconductor
Preliminary
10.7 Crystal Oscillator Timing
10.8 Reset, Stop, Wait, Mode Select, and Interrupt Timing
3. This is the minimum time required after the PLL set up is changed to ensure reliable operation.
Table 10-15 Crystal Oscillator Parameters
Characteristic Symbol Min Typ Max Unit
Crystal Start-up time TCS 4510ms
Resonator Start-up time TRS 0.1 0.18 1 ms
Crystal ESR RESR ——120ohms
Crystal Peak-to-Peak Jitter TD70 — 250 ps
Crystal Min-Max Period Variation TPV 0.12 — 1.5 ns
Resonator Peak-to-Peak Jitter TRJ ——300ps
Resonator Min-Max Period Variation TRP ——300ps
Bias Current, high-drive mode IBIASH —250290μA
Bias Current, low-drive mode IBIASL —80110μA
Quiescent Current, power-down mode IPD —0 1μA
Table 10-16 Reset, Stop, Wait, Mode Select, and Interrupt Timing1,2
1. In the formulas, T = clock cycle. For an operating frequency of 60MHz, T = 16.67ns. At 8MHz (used during Reset and
Stop modes), T = 125ns.
2. Parameters listed are guaranteed by design.
Characteristic Symbol Typical
Min Typical
Max Unit See Figure
Minimum RESET Assertion Duration tRA 16T — ns 10-4
Edge-sensitive Interrupt Request Width tIRW 1.5T — ns 10-5
IRQA, IRQB Assertion to General Purpose
Output Valid, caused by first instruction
execution in the interrupt service rou tine
tIG 18T — ns 10-6
tIG - FAST 14T —
IRQA Width Assertion to Recover from Stop
State3tIW 1.5T — ns 10-8
Reset, Stop, Wait, Mode Select, and Interrupt Timing
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 143
Preliminary
Figure 10-4 Asynchronous Reset Timing
Figure 10-5 External Interrupt Timing (Negative Edge-Sensitive)
Figure 10-6 External Level-Sensitive Interrupt Timing
Figure 10-7 Interrupt from Wait State Timing
3. The interrupt instruction fetch is visible on the pins only in Mode 3.
First Fetch
tRA
tRAZ tRDA
A0–A15,
D0–D15
RESET
IRQA,
IRQB tIRW
tIDM
A0–A15
IRQA,
IRQB
First Interrupt Instruction Execution
a) First Interrupt Instruction Execution
tIG
General
Purpose
I/O Pin
IRQA,
IRQB b) General Purpose I/O
Instruction Fetch
tIRI
IRQA,
IRQB
First Interrupt Vector
A0–A15
56F8345 Technical Data, Rev. 17
144 Freescale Semiconductor
Preliminary
Figure 10-8 Recovery from Stop State Using Asynchronous Interrupt Timing
10.9 Serial Peripheral Interface (SPI) Timing
Table 10-17 SPI Timing1
Characteristic Symbo l Min Max Unit See Figure
Cycle time
Master
Slave
tC50
50 —
—ns
ns
10-9, 10-10,
10-11, 10-12
Enable lead time
Master
Slave
tELD —
25 —
—ns
ns
10-12
Enable lag time
Master
Slave
tELG —
100 —
—ns
ns
10-12
Clock (SCK) high time
Master
Slave
tCH 17.6
25 —
—ns
ns
10-9, 10-10,
10-11, 10-12
Clock (SCK) low time
Master
Slave
tCL 24.1
25 —
—ns
ns
10-12
Data set up time required for inputs
Master
Slave
tDS 20
0—
—ns
ns
10-9, 10-10,
10-11, 10-12
Data hold time required for inputs
Master
Slave
tDH 0
2—
—ns
ns
10-9, 10-10,
10-11, 10-12
Access time (time to data active from
high-impedance state)
Slave
tA4.8 15 ns 10-12
Disable time (hold time to high-impedance state)
Slave tD3.7 15.2 ns 10-12
Data Valid for outputs
Master
Slave (after enable edge)
tDV —
—4.5
20.4 ns
ns
10-9, 10-10,
10-11, 10-12
Not IRQA Interrupt Vector
tIW
IRQA tIF
A0–A15 First Instruction Fetch
Serial Peripheral Interface (SPI) Timing
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 145
Preliminary
Figure 10-9 SPI Master Timing (CPHA = 0)
Data invalid
Master
Slave
tDI 0
0—
—ns
ns
10-9, 10-10,
10-11
Rise time
Master
Slave
tR—
—11.5
10.0 ns
ns
10-9, 10-10,
10-11, 10-12
Fall time
Master
Slave
tF—
—9.7
9.0 ns
ns
10-9, 10-10,
10-11, 10-12
1. Parameters listed are guaranteed by design.
Table 10-17 SPI Timing1 (Continued)
Characteristic Symbo l Min Max Unit See Figure
SCLK (CPOL = 0)
(Output)
SCLK (CPOL = 1)
(Output)
MISO
(Input)
MOSI
(Output)
MSB in Bits 14–1 LSB in
tF
tC
tCL
tCL
tR
tR
tF
tDS
tDH tCH
tDI tDV tDI(ref)
tR
Master MSB out Bits 14–1 Master LSB out
SS
(Input)
tCH
SS is held High on master
tF
56F8345 Technical Data, Rev. 17
146 Freescale Semiconductor
Preliminary
Figure 10-10 SPI Master Timing (CPHA = 1)
SCLK (CPOL = 0)
(Output)
SCLK (CPOL = 1)
(Output)
MISO
(Input)
MOSI
(Output)
MSB in Bits 14–1 LSB in
tR
tC
tCL
tCL
tF
tCH
tDV(ref) tDV tDI(ref)
tR
tF
Master MSB out Bits 14– 1 Master LSB out
SS
(Input)
tCH
SS is held High on master
tDS tDH
tDI
tR
tF
Serial Peripheral Interface (SPI) Timing
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 147
Preliminary
Figure 10-11 SPI Slave Timing (CPHA = 0)
Figure 10-12 SPI Slave Timing (CPHA = 1)
SCLK (CPOL = 0)
(Input)
SCLK (CPOL = 1)
(Input)
MISO
(Output)
MOSI
(Input)
Slave MSB out Bits 14–1
tC
tCL
tCL
tF
tCH
tDI
MSB in Bits 14–1 LSB in
SS
(Input)
tCH
tDH
tR
tELG
tELD
tF
Slave LSB out
tD
tA
tDS tDV tDI
tR
SCLK (CPOL = 0)
(Input)
SCLK (CPOL = 1)
(Input)
MISO
(Output)
MOSI
(Input)
Slave MSB out Bits 14–1
tC
tCL
tCL
tCH
tDI
MSB in Bits 14–1 LSB in
SS
(Input)
tCH
tDH
tF
tR
Slave LSB out
tD
tA
tELD
tDV
tF
tR
tELG
tDV
tDS
56F8345 Technical Data, Rev. 17
148 Freescale Semiconductor
Preliminary
10.10 Quad Timer Timing
Figure 10-13 Timer Timing
10.11 Quadrature Decoder Timing
Table 10-18 Timer Timing1, 2
1. In the formulas listed, T = the clock cycle. For 60MHz operation, T = 16.67ns.
2. Parameters listed are guaranteed by design.
Characteristic Symbol Min Max Unit See Figure
Timer input period PIN 2T + 6 — ns 10-13
Timer input high / low period PINHL 1T + 3 — ns 10-13
Timer output period POUT 1T - 3 — ns 10-13
Timer output high / low period POUTHL 0.5T - 3 — ns 10-13
Table 10-19 Quadrature Decoder Timing1, 2
1. In the formulas listed, T = the clock cycle. For 60MHz operation, T=16.67ns.
2. Parameters listed are guaranteed by design.
Characteristic Symbol Min Max Unit See Figure
Quadrature input period PIN 4T + 12 — ns 10-14
Quadrature input high / low period PHL 2T + 6 — ns 10-14
Quadrature phase period PPH 1T + 3 — ns 10-14
POUT POUTHL POUTHL
PIN PINHL PINHL
Timer Inputs
Timer Outputs
Serial Communication Interface (SCI) Timing
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 149
Preliminary
Figure 10-14 Quadrature Decoder Timing
10.12 Serial Communication Interface (SCI) Timing
Figure 10-15 RXD Pulse Width
Table 10-20 SCI Timing1
1. Parameters listed are guaranteed by design.
Characteristic Symbol Min Max Unit See Figure
Baud Rate2
2. fMAX is the frequency of operation of the system clock, ZCLK, in MHz, which is 60MHz for the 56F8345 device and
40MHz for the 56F8145 device.
BR —(fMAX/16) Mbps —
RXD3 Pulse Width
3. The RXD pin in SCI0 is named RXD0 and the RXD pin in SCI1 is named RXD1.
RXDPW 0.965/BR 1.04/BR ns 10-15
TXD4 Pulse Width
4. The TXD pin in SCI0 is named TXD0 and the TXD pin in SCI1 is named TXD1.
TXDPW 0.965/BR 1.04/BR ns 10-16
Phase B
(Input) PIN PHL
PHL
Phase A
(Input)
PIN PHL
PHL
PPH PPH PPH PPH
RXDPW
RXD
SCI receive
data pin
(Input)
56F8345 Technical Data, Rev. 17
150 Freescale Semiconductor
Preliminary
Figure 10-16 TXD Pulse Width
10.13 Controller Area Network (CAN) Timing
Note: CAN is NOT available in the 56F8145 device.
Figure 10-17 Bus Wake Up Detection
10.14 JTAG Timing
Table 10-21 CAN Timing1
1. Parameters listed are guaranteed by design
Characteristic Symbol Min Max Unit See Figure
Baud Rate BRCAN —1 Mbps —
Bus Wake Up detection T WAKEUP 5—μs10-17
Table 10-22 JTAG Timing
Characteristic Symbol Min Max Unit See Figure
TCK frequency of operation
using EOnCE1fOP DC SYS_CLK/8 MHz 10-18
TCK frequency of operation not
using EOnCE1fOP DC SYS_CLK/4 MHz 10-18
TCK clock pulse width tPW 50 — ns 10-18
TMS, TDI data set-up time tDS 5—ns 10-19
TMS, TDI data hold time tDH 5—ns 10-19
TXDPW
TXD
SCI receive
data pin
(Input)
T WAKEUP
CAN_RX
CAN receive
data pin
(Input)
JTAG Timing
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 151
Preliminary
Figure 10-18 Test Clock Input Timing Diagram
Figure 10-19 Test Access Port Timing Diagram
TCK low to TDO data valid tDV —30ns 10-19
TCK low to TDO tri-state tTS —30ns 10-19
TRST assertion time tTRST 2T2—ns 10-20
1. TCK frequency of operation must be less than 1/8 the processor rate.
2. T = processor clock period (nominally 1/60MHz)
Table 10-22 JTAG Timing
Characteristic Symbol Min Max Unit See Figure
TCK
(Input) VM
VIL
VM = VIL + (VIH – VIL)/2
tPW
1/fOP
tPW
VM
VIH
Input Data Valid
Output Data Valid
Output Data Valid
tDS tDH
tDV
tTS
tDV
TCK
(Input)
TDI
(Input)
TDO
(Output)
TDO
(Output)
TDO
(Output)
TMS
56F8345 Technical Data, Rev. 17
152 Freescale Semiconductor
Preliminary
Figure 10-20 TRST Timing Diagram
10.15 Analog-to-Digital Converter (ADC) Parameters
Table 10-23 ADC Parameters
Characteristic Symbol Min Typ Max Unit
Input voltages VADIN VREFL —V
REFH V
Resolution RES 12 — 12 Bits
Integral Non-Linearity1INL — +/- 2.4 +/- 3.2 LSB2
Differential Non-Linearity DNL — +/- 0.7 < +1 LSB2
Monotonicity GUARANTEED
ADC internal clock fADIC 0.5 — 5 MHz
Conversion range RAD VREFL —V
REFH V
ADC channel power-up time tADPU 5616
tAIC cycles3
ADC reference circuit power-up time4tVREF —— 25ms
Conversion time tADC —6 —
tAIC cycles3
Sample time tADS —1 —
tAIC cycles3
Input capacitance CADI —5 —pF
Input injection current5, per pin IADI —— 3mA
Input injection current, total IADIT —— 20mA
VREFH current IVREFH —1.2 3mA
ADC A current IADCA —25 —mA
ADC B current IADCB —25 —mA
Quiescent current IADCQ —0 10
μA
Uncalibrated Gain Error (ideal = 1) EGAIN — +/- .004 +/- .015 —
TRST
(Input) tTRST
Analog-to-Digital Converter (ADC) Parameters
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 153
Preliminary
Uncalibrated Offset Voltage VOFFSET — +/- 18 +/- 46 mV
Calibrated Absolute Error6AECAL — See Figure 10-21 —LSBs
Calibration Factor 17CF1 — -0.003141 — —
Calibration Factor 27CF2 — -17.6 — —
Crosstalk between channels —— -60 —dB
Common Mode Voltage Vcommon —(V
REFH - VREFLO) / 2 — V
Signal-to-noise ratio SNR — 64.6 — db
Signal-to-noise plus distortion ratio SINAD — 59.1 — db
Total Harmonic Distortion THD — 60.6 — db
Spurious Free Dynamic Range SFDR — 61.1 — db
Effective Number Of Bits8ENOB — 9.6 — Bits
1. INL measured from Vin = .1VREFH to Vin = .9VREFH
10% to 90% Input Signal Range
2. LSB = Least Significant Bit
3. ADC clock cycles
4. Assumes each voltage reference pin is bypassed with 0.1μF ceramic capacitors to ground
5. The current that can be injected or sourced f rom an unselected ADC si gnal input wit hout impacting the pe rformance of
the ADC. This allows the ADC to operate in noisy industrial environments where inductive flyback is possible.
6. Absolute error includes the effects of both gain error and offset error.
7. Please see the 56F8300 Peripheral User’s Manual for additional information on ADC calibration.
8. ENOB = (SINAD - 1.76)/6.02
Table 10-23 ADC Parameters (Continued)
Characteristic Symbol Min Typ Max Unit
56F8345 Technical Data, Rev. 17
154 Freescale Semiconductor
Preliminary
Figure 10-21 ADC Absolute Error Over Processing and Temperature Extremes Before
and After Calibration for VDCin = 0.60V and 2.70V
Note: The absolute error data shown in the graphs above reflects the effects of both gain error and offset
error. The data was taken on 15 parts: three each from four processing corner lots as well as three from one
nominally processed lot, each at three temperatures: -40°C, 27°C, and 150°C (giving the 45 data points
shown above), for two input DC voltages: 0.60V and 2.70V. The data indicates that for the given
population of parts, calibration significantly reduced (by as much as 39%) the collective variation (spread)
of the absolute error of the population. It also significantly reduced (by as much as 80%) the mean
(average) of the absolute error and thereby brought it significantly closer to the ideal value of zero.
Although not guaranteed, it is believed that calibration will produce results similar to those shown above
for any population of parts including those which represent processing and temperature extremes.
Equivalent Circuit for ADC Inputs
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 155
Preliminary
10.16 Equivalent Circuit for ADC Inputs
Figure 10-22 illustrates the ADC input circuit during sample and hold. S1 and S2 are always open/closed
at the same time that S3 is closed/open. When S1/S2 are closed & S3 is open, one input of the sample and
hold circuit moves to VREFH - VREFH / 2, while the other charges to the analog input voltage. When the
switches are flipped, the charge on C1 and C2 are averaged via S3, with the result that a single-ended
analog input is switched to a differential voltage centered about VREFH - VREFH / 2. The switches switch
on every cycle of the ADC clock (open one-half ADC clock, closed one-half ADC clock). Note that there
are additional capacitances associated with the analog input pad, routing, etc., but these do not filter into
the S/H output voltage, as S1 provides isolation during the charge-sharing phase.
One aspect of this circuit is that there is an on-going input current, which is a function of the analog input
voltage, VREF and the ADC clock frequency.
56F8345 Technical Data, Rev. 17
156 Freescale Semiconductor
Preliminary
1. Parasitic capacitance due to package, pin-to-pin and pin-to-package base coupling; 1.8pf
2. Parasitic capacitance due to the chip bond pad, ESD protection devices and signal routing; 2.04pf
3. Equivalent resistance for the ESD isolation resistor and the channel select mux; 500 ohms
4. Sampling capacitor at the sample and hold circuit. Capacitor C1 is normally disconnected from the input and is only
connected to it at sampling time; 1pf
Figure 10-22 Equivalent Circuit for A/D Loading
10.17 Power Consumption
This section provides additional detail which can be used to optimize power consumption for a given
application.
Power consumption is given by the following equation:
A, the internal [static component], is comprised of the DC bias currents for the oscillator, leakage current,
PLL, and voltage references. These sources operate independently of processor state or operating
frequency.
B, the internal [state-dependent component], reflects the supply current required by certain on-chip
resources only when those resources are in use. These include RAM, Flash memory and the ADCs.
C, the internal [dynamic component], is classic C*V2*F CMOS power dissipation corresponding to the
56800E core and standard cell logic.
D, the external [dynamic component], reflects power dissipated on-chip as a result of capacitive loading
on the external pins of the chip. This is also commonly described as C*V2*F, although simulations on two
of the IO cell types used on the device reveal that the power-versus-load curve does have a non-zero
Y-intercept.
Total power = A: internal [static component]
+B: internal [state-dependent component]
+C: internal [dynamic component]
+D: external [dynamic component]
+E: external [static]
12
3
Analog Input 4
S1
S2
S3
C1
C2
S/H
C1 = C2 = 1pF
(VREFH - VREFLO) / 2
Power Consumption
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 157
Preliminary
Power due to capacitive loading on output pins is (first order) a function of the capacitive load and
frequency at which the outputs change. Table 10-24 provides coefficients for calculating power dissipated
in the IO cells as a function of capacitive load. In these cases:
Total Power = Σ((Intercept +Slope*Cload)*frequency/10MHz)
where:
• Summation is performed over all output pins with capacitive loads
• Total Power is expressed in mW
• Cload is expressed in pF
Because of the low duty cycle on most device pins, power dissipation due to capacitive loads was found
to be fairly low when averaged over a period of time.
E, the external [static component], reflects the effects of placing resistive loads on the outputs of the
device. Sum the total of all V2/R or IV to arrive at the resistive load contribution to power. Assume V =
0.5 for the purposes of these rough calculations. For instance, if there is a total of eight PWM outputs
driving 10mA into LEDs, then P = 8*.5*.01 = 40mW.
In previous discussions, power consumption due to parasitics associated with pure input pins is ignored,
as it is assumed to be negligible.
Table 10-24 IO Loading Coefficients at 10MHz
Intercept Slope
PDU08DGZ_ME 1.3 0.11mW / pF
PDU04DGZ_ME 1.15mW 0.11mW / pF
56F8345 Technical Data, Rev. 17
158 Freescale Semiconductor
Preliminary
Part 11 Packaging
11.1 56F8345 Package and Pin-Out Information
This section contains package and pin-out information for the 56F8345. This device comes in a 128-pin
Low-profile Quad Flat Pack (LQFP). Figure 11-1. shows the package outline for the 128-pin LQFP,
Figure 11-3 shows the mechanical parameters for this package, and Table 11-1 lists the pin-out for the
128-pin LQFP. Please see freescale.com on the 56F8145 product page for the 128-pin LQFP Mechanical
Case Outline (link located with orderable part number).
56F8345 Package and Pin-Out Information
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 159
Preliminary
Figure 11-1 Top View, 56F8345 128-pin LQFP Package
Table 11-1 56F8345 128-Pin LQFP Package Identification by Pin Number
Pin No. Signal Na me Pin No. Signal Name Pin No. Signa l Name Pin No. Signal Name
1 INDEX0 33 PWMB1 65 VSS 97 ANB1
2 HOME0 34 PWMB2 66 PWMA5 98 ANB2
3V
SS 35 VSS 67 FAULTA0 99 ANB3
4V
DD_IO 36 VDD_IO 68 FAULTA1 100 ANB4
103
PIN 1
39 65
INDEX0
HOME0
VSS
VDD_IO
CLKO
VPP2
HOME1
PHASEB1
PHASEA1
RXD0
TXD0
INDEX1
GPIOA0
GPIOA1
GPIOA2
GPIOA3
GPIOA4
GPIOA5
VDD_IO
VCAP4
VSS
GPIOF0
GPIOF1
GPIOF2
GPIOF3
GPIOB0
VDD_IO
GPIOB1
GPIOB2
GPIOB3
GPIOB4
PWMB0
TXD1
RXD1
PWMB1
PWMB2
VSS
VDD_IO
PWMB3
PWMB4
PWMB5
GPIOD0
ISB0
VCAP1
IRQA
FAULTB0
GPIOD1
GPIOD2
GPIOD3
GPIOD4
GPIOD5
ISB1
ISB2
IRQB
FAULTB1
FAULTB2
FAULTB3
PWMA0
PWMA1
PWMA2
PWMA3
PWMA4
VSS
VDD_IO
PWMA5
VSS
FAULTA0
FAULTA1
FAULTA2
FAULTA3
OCR_DIS
VDDA_OSC_PLL
XTAL
EXTAL
VCAP3
RSTO
CLKMODE
ANA0
VDD_IO
RESET
ANA7
ANA3
ANA2
ANA6
ANA4
ANA1
ANA5
TEMP_SENSE
VREFH
VREFP
VREFMID
VREFN
VREFLO
VDDA_ADC
VSSA_ADC
ISA0
ANB6
ANB5
ANB4
ANB3
ANB2
ANB1
ANB0
ANB7
ISA2
ISA1
TD0
TD3
TD2
TD1
TC1
TC0
VDD_IO
TDI
TMS
TCK
TRST
PHASEB0
VCAP2
CAN_RX
VPP1
TDO
CAN_TX
PHASEA0
MOSI0
MISO0
SCLK0
SS0
Mark
Orientation
56F8345 Technical Data, Rev. 17
160 Freescale Semiconductor
Preliminary
5V
PP2 37 PWMB3 69 FAULTA2 101 ANB5
6 CLKO 38 PWMB4 70 FAULTA3 102 ANB6
7 TXD0 39 PWMB5 71 OCR_DIS 103 ANB7
8RXD040TXD172V
DDA_OSC_PLL 104 ISA0
9 PHASEA1 41 RXD1 73 XTAL 105 ISA1
10 PHASEB1 42 GPIOD0 74 EXTAL 106 ISA2
11 INDEX1 43 GPIOD1 75 VCAP3 107 TD0
12 HOME1 44 GPIOD2 76 VDD_IO 108 TD1
13 VCAP4 45 GPIOD3 77 RSTO 109 TD2
14 VDD_IO 46 GPIOD4 78 RESET 110 TD3
15 GPIOA0147 GPIOD5 79 CLKMODE 111 TC0
16 GPIOA1148 ISB0 80 ANA0 112 VDD_IO
17 GPIOA2149 VCAP1 81 ANA1 113 TC1
18 GPIOA3150 ISB1 82 ANA2 114 TRST
19 GPIOA4151 ISB2 83 ANA3 115 TCK
20 GPIOA5152 IRQA 84 ANA4 116 TMS
21 VSS 53 IRQB 85 ANA5 117 TDI
20 GPIOF0154 FAULTB0 86 ANA6 118 TDO
23 GPIOF1155 FAULTB1 87 ANA7 119 VPP1
24 GPIOF2156 FAULTB2 88 TEMP_SENSE 120 CAN_TX
25 VDD_IO 57 FAULTB3 89 VREFLO 121 CAN_RX
1. Primary function is not available in this package configuration; GPIO functi on must be used instead
26 GPIOF3158 PWMA0 90 VREFN 122 VCAP2
27 GPIOB0 59 VSS 91 VREFMID 123 SS0
28 GPIOB1 60 PWMA1 92 VREFP 124 SCLK0
29 GPIOB2 61 PWMA2 93 VREFH 125 MISO0
30 GPIOB3 62 VDD_IO 94 VDDA_ADC 126 MOSI0
31 GPIOB4 63 PWMA3 95 VSSA_ADC 127 PHASEA0
Table 11-1 56F8345 128-Pin LQFP Package Identification by Pin Number (Continued)
Pin No. Signal Na me Pin No. Signal Name Pin No. Signa l Name Pin No. Signal Name
56F8145 Package and Pin-Out Information
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 161
Preliminary
11.2 56F8145 Package and Pin-Out Information
This section contains package and pin-out information for the 56F8145. This device comes in a 128-pin
Low-profile Quad Flat Pack (LQFP). Figure 11-1. shows the package outline for the 128-pin LQFP,
Figure 11-3 shows the mechanical parameters for this package, and Table 11-1 lists the pin-out for the
128-pin LQFP. Please see freescale.com on the 56F8145 product page for the 128-pin LQFP Mechanical
Case Outline (link located with orderable part number).
32 PWMB0 64 PWMA4 96 ANB0 128 PHASEB0
Table 11-1 56F8345 128-Pin LQFP Package Identification by Pin Number (Continued)
Pin No. Signal Na me Pin No. Signal Name Pin No. Signa l Name Pin No. Signal Name
56F8345 Technical Data, Rev. 17
162 Freescale Semiconductor
Preliminary
Figure 11-2 Top View, 56F8145 128-pin LQFP Package
103
PIN 1
39 65
INDEX0
HOME0
VSS
VDD_IO
CLKO
VPP2
SS1
MOSI1
SCLK1
RXD0
TXD0
MISO1
GPIOA0
GPIOA1
GPIOA2
GPIOA3
GPIOA4
GPIOA5
VDD_IO
VCAP4
VSS
GPIOF0
GPIOF1
GPIOF2
GPIOF3
GPIOB0
VDD_IO
GPIOB1
GPIOB2
GPIOB3
GPIOB4
PWMB0
TXD1
RXD1
PWMB1
PWMB2
VSS
VDD_IO
PWMB3
PWMB4
PWMB5
GPIOD0
ISB0
VCAP1
IRQA
FAULTB0
GPIOD1
GPIOD2
GPIOD3
GPIOD4
GPIOD5
ISB1
ISB2
IRQB
FAULTB1
FAULTB2
FAULTB3
NC
NC
NC
NC
NC
VSS
VDD_IO
NC
VSS
NC
NC
NC
NC
OCR_DIS
VDDA_OSC_PLL
XTAL
EXTAL
VCAP3
RSTO
CLKMODE
ANA0
VDD_IO
RESET
ANA7
ANA3
ANA2
ANA6
ANA4
ANA1
ANA5
NC
VREFH
VREFP
VREFMID
VREFN
VREFLO
VDDA_ADC
VSSA_ADC
GPIOC8
ANB6
ANB5
ANB4
ANB3
ANB2
ANB1
ANB0
ANB7
GPIOC10
GPIOC9
GPIOE10
GPIOE13
GPIOE12
GPIOE11
TC1
TC0
VDD_IO
TDI
TMS
TCK
TRST
PHASEB0
VCAP2
NC
VPP1
TDO
NC
PHASEA0
MOSI0
MISO0
SCLK0
SS0
Mark
Orientation
56F8145 Package and Pin-Out Information
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 163
Preliminary
Table 11-2 56F8145 128-Pin LQFP Package Identification by Pin Number
Pin No. Signal Na me Pin No. Signal Name Pin No. Signa l Name Pin No. Signal Name
1 INDEX0 33 PWMB1 65 VSS 97 ANB1
2 HOME0 34 PWMB2 66 NC 98 ANB2
3V
SS 35 VSS 67 NC 99 ANB3
4V
DD_IO 36 VDD_IO 68 NC 100 ANB4
5V
PP2 37 PWMB3 69 NC 101 ANB5
6 CLKO 38 PWMB4 70 NC 102 ANB6
7 TXD0 39 PWMB5 71 OCR_DIS 103 ANB7
8RXD040TXD172V
DDA_OSC_PLL 104 GPIOC8
9 SCLK1 41 RXD1 73 XTAL 105 GPIOC9
10 MOSI1 42 GPIOD0 74 EXTAL 106 GPIOC10
11 MISO1 43 GPIOD1 75 VCAP3 107 GPIOE10
12 SS1 44 GPIOD2 76 VDD_IO 108 GPIOE11
13 VCAP4 45 GPIOD3 77 RSTO 109 GPIOE12
14 VDD_IO 46 GPIOD4 78 RESET 110 GPIOE13
15 GPIOA0147 GPIOD5 79 CLKMODE 111 TC0
16 GPIOA1148 ISB0 80 ANA0 112 VDD_IO
17 GPIOA2149 VCAP1 81 ANA1 113 TC1
18 GPIOA3150 ISB1 82 ANA2 114 TRST
19 GPIOA4151 ISB2 83 ANA3 115 TCK
20 GPIOA5152 IRQA 84 ANA4 116 TMS
21 VSS 53 IRQB 85 ANA5 117 TDI
22 GPIOF0154 FAULTB0 86 ANA6 118 TDO
23 GPIOF1155 FAULTB1 87 ANA7 119 VPP1
24 GPIOF2156 FAULTB2 88 NC 120 NC
25 VDD_IO 57 FAULTB3 89 VREFLO 121 NC
1. Primary function is not available in this package configuration; GPIO functi on must be used instead
56F8345 Technical Data, Rev. 17
164 Freescale Semiconductor
Preliminary
26 GPIOF3158 NC 90 VREFN 122 VCAP2
27 GPIOB0 59 VSS 91 VREFMID 123 SS0
28 GPIOB1 60 NC 92 VREFP 124 SCLK0
29 GPIOB2 61 NC 93 VREFH 125 MISO0
30 GPIOB3 62 VDD_IO 94 VDDA_ADC 126 MOSI0
31 GPIOB4 63 NC 95 VSSA_ADC 127 PHASEA0
32 PWMB0 64 NC 96 ANB0 128 PHASEB0
Table 11-2 56F8145 128-Pin LQFP Package Identification by Pin Number (Continued)
Pin No. Signal Na me Pin No. Signal Name Pin No. Signa l Name Pin No. Signal Name
56F8145 Package and Pin-Out Information
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 165
Preliminary
Figure 11-3 128-pin LQFP Mechanical Information
NOTES:
1. DIMENSIONING AND TOLERANCING PER ASME
Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMET ER.
3. DATUM PLANE H IS LOCATED AT BOTTOM OF LEAD
AND IS COINCIDENT WITH THE LEAD WHERE THE
LEAD EXITS THE PLASTIC BODY AT THE BOTTOM OF
THE PARTING LINE.
4. DATUMS A, B, AND D TO BE DETERMINED AT DATUM
PLANE H.
5. DIMENSIONS D AND E TO BE DETERMINED AT
SEATING PLANE C.
6. DIMENSIONS D1 AND E1 DO NOT INCLUDE MOLD
PROTRUSION. ALLOWABLE PROTRUSION IS 0.25 PER
SIDE. DIMENSIONS D1 AND E1 DO INCLUDE MOLD
MISMATCH AND ARE DETERMINED AT DATUM
PLANE H.
7. DIMENSION b DOES NOT INCLUDE DAMBAR
PROTRUSION. DAMBAR PROTRUSION SHALL NOT
CAUSE THE b DIMENSION TO EXCEED 0.35.
DIM MILLIMETERS
MIN MAX
A --- 1.60
A1 0.05 0.15
A2 1.35 1.45
b 0.17 0.27
b1 0.17 0.23
c 0.09 0.20
c1 0.09 0.16
D 22.00 BSC
D1 20.00BSC
e 0.50 BSC
E 16.00 BSC
E1 14.00 BSC
L 0.45 0.75
L1 1.00 REF
L2 0.50 REF
S 0.20 ---
R1 0.08 ---
R2 0.08 0.20
00o7o
01 0o---
02 11o13o
56F8345 Technical Data, Rev. 17
166 Freescale Semiconductor
Preliminary
Please see www.freescale.com for the most current case outline.
Thermal Design Considerations
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 167
Preliminary
Part 12 Design Considerations
12.1 Thermal Design Considerations
An estimation of the chip junction temperature, TJ, can be obtained from the equation:
TJ = TA + (RθJΑ x PD)
where:
The junction-to-ambient thermal resistance is an industry-standard value that provides a quick and easy
estimation of thermal performance. Unfortunately, there are two values in common usage: the value
determined on a single-layer board and the value obtained on a board with two planes. For packages such
as the PBGA, these values can be different by a factor of two. Which value is closer to the application
depends on the power dissipated by other components on the board. The value obtained on a single-layer
board is appropriate for the tightly packed printed circuit board. The value obtained on the board with the
internal planes is usually appropriate if the board has low-power dissipation and the components are well
separated.
When a heat sink is used, the thermal resistance is expressed as the sum of a junction-to-case thermal
resistance and a case-to-ambient thermal resistance:
RθJA = RθJC + RθCA
where:
RθJC is device-related and cannot be influenced by the user. The user controls the thermal environment to
change the case-to-ambient thermal resistance, RθCA . For instance, the user can change the size of the heat
sink, the air flow around the device, the interface material, the mounting arrangement on printed circuit
board, or change the thermal dissipation on the printed circuit board surrounding the device.
To determine the junction temperature of the device in the application when heat sinks are not used, the
Thermal Characterization Parameter (ΨJT) can be used to determine the junction temperature with a
measurement of the temperature at the top center of the package case using the following equation:
TJ = TT + (ΨJT x PD)
where:
TA= Ambient temperature for the package (oC)
RθJΑ= Junction-to-ambient thermal resistance (oC/W)
PD= Power dissipation in the package (W)
RθJA = Package junction-to-ambient thermal resistance °C/W
RθJC = Package junction-to-case thermal resistance °C/W
RθCA = Package case-to-ambient thermal resistance °C/W
TT= Thermocouple temperature on top of package (oC)
ΨJT = Thermal characterization parameter (oC)/W
PD= Power dissipation in package (W)
56F8345 Technical Data, Rev. 17
168 Freescale Semiconductor
Preliminary
The thermal characterization parameter is measured per JESD51-2 specification using a 40-gauge type T
thermocouple epoxied to the top center of the package case. The thermocouple should be positioned so
that the thermocouple junction rests on the package. A small amount of epoxy is placed over the
thermocouple junction and over about 1mm of wire extending from the junction. The thermocouple wire
is placed flat against the package case to avoid measurement errors caused by cooling effects of the
thermocouple wire.
When heat sink is used, the junction temperature is determined from a thermocouple inserted at the
interface between the case of the package and the interface material. A clearance slot or hole is normally
required in the heat sink. Minimizing the size of the clearance is important to minimize the change in
thermal performance caused by removing part of the thermal interface to the heat sink. Because of the
experimental difficulties with this technique, many engineers measure the heat sink temperature and then
back-calculate the case temperature using a separate measurement of the thermal resistance of the
interface. From this case temperature, the junction temperature is determined from the junction-to-case
thermal resistance.
12.2 Electrical Design Considerations
Use the following list of considerations to assure correct operation of the 56F8345/56F8145:
• Provide a low-impedance path from the board power supply to each VDD pin on the device, and from the
board ground to each VSS (GND) pin
• The minimum bypass requirement is to place six 0.01–0.1μF capacitors positioned as close as possible to
the package supply pins. The recommended bypass configuration is to place one bypass capacitor on each
of the VDD/VSS pairs, including VDDA/VSSA. Ceramic and tantalum capacitors tend to provide better
performance tolerances.
• Ensure that capacitor leads and associated printed circuit traces that connect to the chip VDD and VSS (GND)
pins are less than 0.5 inch per capacitor lead
• Use at least a four-layer Printed Circuit Board (PCB) with two inner layers for VDD and VSS
• Bypass the VDD and VSS layers of the PCB with approximately 100μF, preferably with a high-grade
capacitor such as a tantalum ca pacitor
CAUTION
This device contains protective circuitry to guard
against damage due to high static voltage or electrical
fields. However, normal precautions are advised to
avoid application of any voltages higher than
maximum-rated voltages to this high-impedance circuit.
Reliability of operation is enhanced if unused inputs are
tied to an appropriate voltage level.
Power Distribution and I/O Ring Implementation
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 169
Preliminary
• Because the device’s output signals have fast rise and fall times, PCB trace lengths should be minimal
• Consider all device loads as well as parasitic capacitance due to PCB traces when calculating capacitance.
This is especially critical in systems with higher capacitive loads that could create higher transient currents
in the VDD and VSS circuits.
• Take special care to minimize noise levels on the VREF, VDDA and VSSA pins
• Designs that utilize the TRST pin for JTAG port or OnCE module functionality (such as development or
debugging systems) should allow a means to assert TRST whenever RESET is asserted, as well as a means
to assert TRST independently of RESET. Designs that do not require debugging functionality, such as
consumer products, should tie these pins together.
• Because the Flash memory is programmed through the JTAG/OnCE port, the de signer should provide an
interface to this port to allow in-circuit Flash programming
12.3 Power Distribution and I/O Ring Implementation
Figure 12-1 illustrates the general power control incorporated in the 56F8345/56F8145. This chip
contains two internal power regulators. One of them is powered from the VDDA_OSC_PLL pin and cannot
be turned off. This regulator controls power to the internal clock generation circuitry. The other regulator
is powered from the VDD_IO pins and provides power to all of the internal digital logic of the core, all
peripherals and the internal memories. This regulator can be turned off, if an external VDD_CORE voltage
is externally applied to the VCAP pins.
In summary, the entire chip can be supplied from a single 3.3 volt supply if the large core regulator is
enabled. If the regulator is not enabled, a dual supply 3.3V/2.5V configuration can also be used.
Notes:
• Flash, RAM and internal logic are powered from the core regulator output
•V
PP1 and VPP2 are not connected in the customer system
• All circuitry, analog and digital, shares a common VSS bus
Figure 12-1 Power Management
REG
CORE
VCAP
I/O ADC
VDD
VSS
REG
VDDA_OSC_PLL
OSC
VSSA_ADC
VDDA_ADC
VREFH
VREFP
VREFMID
VREFN
VREFLO
56F8345 Technical Data, Rev. 17
170 Freescale Semiconductor
Preliminary
Part 13 Ordering Information
Table 13-1 lists the pertinent information needed to place an order. Consult a
Freescale
Semiconductor
sales office or authorized distributor to determine availability and to order parts.
*This package is RoHS compliant.
Table 13-1 Ordering Information
Part Supply
Voltage Package Type Pin
Count Frequency
(MHz)
Ambient
Temperature
Range Order Number
MC56F8345 3.0–3.6 V Low-Profile Quad Flat Pack (LQFP) 128 60 -40° to + 105° C MC56F8345VFG60
MC56F8345 3.0–3.6 V Low-Profile Quad Flat Pack (LQFP) 128 60 -40° to + 125° C MC56F8345MFG60
MC56F8145 3.0–3.6 V Low-Profile Quad Flat Pack (LQFP) 128 40 -40° to + 105° C MC56F8145VFG
MC56F8345 3.0–3.6 V Low-Profile Quad Flat Pack (LQFP) 128 60 -40° to + 105° C MC56F8345VFGE*
MC56F8345 3.0–3.6 V Low-Profile Quad Flat Pack (LQFP) 128 60 -40° to + 125° C MC56F8345MFGE*
MC56F8145 3.0–3.6 V Low-Profile Quad Flat Pack (LQFP) 128 40 -40° to + 105° C MC56F8145VFGE*
Power Distribution and I/O Ring Implementation
56F8345 Technical Data, Rev. 17
Freescale Semiconductor 171
Preliminary
THIS PAGE IS INTENTIONALLY BLANK
How to Reach Us:
Home Page:
www.freescale.com
E-mail:
support@freescale.com
USA/Europe or Locations Not Listed:
Freescale Semiconductor
Technical Information Center, CH370
1300 N. Alma School Road
Chandler, Arizona 85224
+1-800-521-6274 or +1-480-768-2130
support@freescale.com
Europe, Middle East, and Africa:
Freescale Halbleiter Deutschland GmbH
Technical Information Center
Schatzbogen 7
81829 Muenchen, Germany
+44 1296 380 456 (English)
+46 8 52200080 (English)
+49 89 92103 559 (German)
+33 1 69 35 48 48 (French)
support@freescale.com
Japan:
Freescale Semiconductor Japan Ltd.
Headquarters
ARCO Tower 15F
1-8-1, Shimo-Meguro, Meguro-ku,
Tokyo 153-0064, Japan
0120 191014 or +81 3 5437 9125
support.japan@freescale.com
Asia/Pacific:
Freescale Semiconductor Hong Kong Ltd.
Technical Information Center
2 Dai King Street
Tai Po Industrial Estate
Tai Po, N.T., Hong Kong
+800 2666 8080
support.asia@freescale.com
For Literature Requests Only:
Freescale Semiconductor Literature Distribution Center
P.O. Box 5405
Denver, Colorado 80217
1-800-441-2447 or 303-675-2140
Fax: 303-675-2150
LDCForFreescaleSemiconductor@hibbertgroup.com
Freescale™ and th e Freesca le lo go a re t radema rks o f Free scale Se micond ucto r,
Inc. All oth er produ ct or se rvice nam es are t he proper ty of th eir respe ctive ow ners.
This product incorporates Supe rFlash® technology licensed from SST.
© Freescale Semiconductor, Inc. 2005, 2006. All rights reserved.
MC56F8345
Rev. 17
01/2007
Information in this document is provided solely to enable system and
software implementers to use Freescale Semiconducto r product s. There are
no express or implied copyright licenses granted hereunder to design or
fabricate any integrated circuits or integrated circuits based on the
information in this document.
Freescale Semicond uctor reserves the right to m ake changes without furt her
notice to any prod ucts herein . Freescale Semicond uctor makes no warranty,
representation or guarantee regarding the suitability of its products for any
particular purpose, nor does Freescale Semiconductor assume any liability
arising out of the ap plicat ion or use of any product or circu it, and specifi cally
disclaims any and all liability, including without limitation consequential or
incidenta l damages. “ T ypical” parame ters that may be provided in Freescale
Semiconducto r data sheets and/or specifica tions can and do vary in different
applications and actual performance may vary over time. All oper ating
parameters, including “Typicals”, must be validated for each customer
application by custo mer’s technical expert s. Frees cale Semicon ductor does
not convey any license under its patent rights nor the rights of others.
Freescale Semiconductor products are not designed, intended, or author ized
for use as component s in systems intended for surgical implant in to the body ,
or other applications intended to support or sustain life, or for any other
application in w hich the failure of the Freescale Semiconduct or product could
create a situation where personal injury or death may occur. Should Buyer
purchase or use Free scale Semiconductor product s for any such unintended
or unauthorized application, Buyer shall indemnify and hold Freescale
Semiconductor and its officers, employees, subsidiaries, affiliates, and
distributors h armless against all claims, costs, damages, and expen ses, and
reasonable attorney fees arising out of, directly or indirectly, any claim of
personal injury or death associated with such unintended or unauthorized
use, even if such clai m alleges that Freescale Semiconducto r was negligent
regarding the design or manufacture of the part.
RoHS-compliant and/or Pb-free versions of Freescale products have the
functionality and electr ical characteristics of their non-RoHS- compliant
and/or non-Pb-free counterparts. For further information, see
http://www.freescale.com or contact your Freescale sales representative.
For information on Freescale’s Environmental Products program, go to
http://www.freescale.com/epp.
