Dome Packages
The HLMP-6xxx Series dome
lamps for use as indicators use a
tinted, diffused lens to provide a
wide viewing angle with a high
on-off contrast ratio. High
brightness lamps use an untinted,
nondiffused lens to provide a high
luminous intensity within a
narrow radiation pattern.
Resistor Lamps
The HLMP-6xxx Series 5 volt
subminiature lamps with built in
current limiting resistors are for
use in applications where space is
at a premium.
Lead Configurations
All of these devices are made by
encapsulating LED chips on axial
lead frames to form molded epoxy
subminiature lamp packages. A
variety of package configuration
options is available. These
Features
• Subminiature Flat Top
Package
Ideal for Backlighting and
Light Piping Applications
• Subminiature Dome
Package
Diffused Dome for Wide
Viewing Angle
Nondiffused Dome for High
Brightness
• TTL and LSTTL Compatible
5 Volt Resistor Lamps
• Available in Six Colors
• Ideal for Space Limited
Applications
• Axial Leads
• Available with Lead
Configurations for Surface
Mount and Through Hole PC
Board Mounting
Description
Flat Top Package
The HLMP-Pxxx Series flat top
lamps use an untinted, non-
diffused, truncated lens to provide
a wide radiation pattern that is
necessary for use in backlighting
applications. The flat top lamps
are also ideal for use as emitters
in light pipe applications.
Subminiature LED Lamps
Technical Data
HLMP-Pxxx Series
HLMP-Qxxx Series
HLMP-6xxx Series
HLMP-70xx Series
include special surface mount
lead configurations, gull wing,
yoke lead or Z-bend. Right angle
lead bends at 2.54 mm (0.100
inch) and 5.08 mm (0.200 inch)
center spacing are available for
through hole mounting. For
more information refer to
Standard SMT and Through
Hole Lead Bend Options for
Subminiature LED Lamps data
sheet.
2
DH AS High High Device
Standard AlGaAs Efficiency Perf. Emerald Outline
Red Red Red Orange Yellow Green Green Device Description[1] Drawing
P105 P205 P405 P305 P505 P605 Untinted, Nondiffused, A
Flat Top
P102 P202 P402 P302 P502 Untinted, Diffused, B
Flat Top
6000/6001 Q101 6300 Q400 6400 6500 Q600 Tinted, Diffused
Q105 6305 6405 6505 Untinted, Nondiffused,
High Brightness
Q150 7000 7019 7040 Tinted, Diffused, Low B
Current
Q155 Nondiffused, Low
Current
6600 6700 6800 Tinted, Diffused,
Resistor, 5 V, 10 mA
6620 6720 6820 Diffused, Resistor, 5 V,
4 mA
Device Selection Guide
Part Number: HLMP-xxxx
Package Dimensions
(A) Flat Top Lamps
0.46
0.56 (0.018)
(0.022)
1.40
1.65(0.055)
(0.065)
0.25 (0.010) MAX.*
NOTE 2
0.20 (0.008) MAX.
0.50 (0.020) REF.
CATHODE
1.65
1.91(0.065)
(0.075)DIA.
ANODE
11.68
10.67(0.460)
(0.420)
BOTH SIDES
1.14
1.40 (0.045)
(0.055) 0.63
0.38 (0.025)
(0.015)
2.21
1.96(0.087)
(0.077)
0.18
0.23(0.007)
(0.009)
0.79 (0.031) MAX.
2.44
1.88(0.096)
(0.074)
2.08
2.34(0.082)
(0.092)
CATHODE
STRIPE
NOTES:
1. ALL DIMENSIONS ARE IN MILLIMETRES (INCHES).
2. PROTRUDING SUPPORT TAB IS CONNECTED TO CATHODE LEAD. * REFER TO FIGURE 1 FOR DESIGN CONCERNS.
3
Package Dimensions (cont.)
(B) Diffused and Nondiffused
Figure 1. Proper Right Angle Mounting to a PC Board to Prevent Protruding Cathode Tab from Shorting
to Anode Connection.
NOTES:
1. ALL DIMENSIONS ARE IN MILLIMETRES (INCHES).
2. PROTRUDING SUPPORT TAB IS CONNECTED TO CATHODE LEAD.
0.50 (0.020) REF. 0.94
1.24 (0.037)
(0.049)
2.92 (0.115)
MAX.
0.76
0.89 (0.030)
(0.035)R.
0.63
0.38(0.025)
(0.015)
2.03 (0.080)
1.78 (0.070)
0.79 (0.031)
0.53 (0.021)
0.46
0.56(0.018)
(0.022)
0.25 (0.010) MAX.*
NOTE 2
0.20 (0.008) MAX.
CATHODE
1.65
1.91(0.065)
(0.075)DIA.
ANODE
11.68
10.67(0.460)
(0.420)
BOTH SIDES
0.18
0.23(0.007)
(0.009)
2.08
2.34(0.082)
(0.092)
CATHODE
STRIPE
2.21
1.96(0.087)
(0.077)
* REFER TO FIGURE 1 FOR DESIGN CONCERNS.
NO. ANODE DOWN. YES. CATHODE DOWN.
CATHODE
TAB
4
DH AS High High
Standard AlGaAs Eff. Perf. Emerald
Parameter Red Red Red Orange Yellow Green Green Units
DC Forward Current[1] 50 30 30 30 20 30 30 mA
Peak Forward Current[2] 1000 300 90 90 60 90 90 mA
DC Forward Voltage 6 6 6 6 V
(Resistor Lamps Only)
Reverse Voltage (IR = 100 µA)5 555555V
Transient Forward Current[3] 2000 500 500 500 500 500 500 mA
(10 µs Pulse)
Operating Temperature Range: -55 to -40 to -55 to +100 -40 to -20 to
Non-Resistor Lamps +100 +100 +100 +100 °C
Resistor Lamps -40 to +85 -20 to
+85
Storage Temperature Range °C
For Thru Hole Devices 260°C for 5 Seconds
Wave Soldering Temperature
[1.6 mm (0.063 in.) from body]
For Surface Mount Devices:
Convective IR 235°C for 90 Seconds
Vapor Phase 215°C for 3 Minutes
Absolute Maximum Ratings at TA = 25°C
-55 to +100
Notes:
1. See Figure 5 for current derating vs. ambient temperature. Derating is not applicable to resistor lamps.
2. Refer to Figure 6 showing Max. Tolerable Peak Current vs. Pulse Duration to establish pulsed operating conditions.
3. The transient peak current is the maximum non-recurring peak current the device can withstand without failure. Do not operate these
lamps at this high current.
5
Electrical/Optical Characteristics, TA = 25°C
Standard Red
Device
HLMP- Parameter Symbol Min. Typ. Max. Units Test Conditions
6000 Luminous Intensity[1] Iv0.5 1.2 mcd IF = 10 mA
6001 1.3 3.2
Forward Voltage VF1.4 1.6 2.0 V IF = 10 mA
All Reverse Breakdown VR5.0 12.0 V IR = 100 µA
Voltage
P005 Included Angle Between 125
Half Intensity Points[2] 2θ1/2Deg.
All 90
Others
Peak Wavelength λPEAK 655 nm
Dominant Wavelength[3] λd640 nm
Spectral Line Half Width ∆λ1/2 24 nm
All Speed of Response τs15 ns
Capacitance C 100 pF VF = 0; f = 1 MHz
Thermal Resistance RθJ-PIN 170 °C/W Junction-to-Cathode
Lead
Luminous Efficacy[4] ηv65 lm/W
6
Device
HLMP- Parameter Symbol Min. Typ. Max. Units Test Conditions
P102 4.0 20.0
P105 8.6 30.0
Q101 22.0 45.0
Q105 Luminous Intensity Iv40 200 mcd
Q150 1.0 1.8
Q155 2.0 4.0
Q101 1.8 2.2 IF = 20 mA
P205/P505 Forward Voltage VF1.8 2.2 V
Q101/Q105
Q150/Q155 1.6 1.8 IF = 1 mA
All Reverse Breakdown VR5.0 15.0 V IR = 100 µA
Voltage
P105 125
Q101/Q150 Included Angle Between 2θ1/290 Deg.
Half Intensity Points[2]
Q105/Q155 28
Peak Wavelength λPEAK 645 nm Measured at Peak
Dominant Wavelength[3] λd637 nm
Spectral Line Half Width ∆λ1/2 20 nm
All Speed of Response τs30 ns Exponential Time
Constant; e-t/τ
Capacitance C 30 pF VF = 0; f = 1 MHz
Thermal Resistance RθJ-PIN 170 °C/W Junction-to
Cathode Lead
Luminous Efficacy[4] ηv80 lm/W
DH AS AlGaAs Red
IF = 1 mA
IF = 20 mA
s
7
Device
HLMP- Parameter Symbol Min. Typ. Max. Units Test Conditions
P202 1.0 5.0
P205 1.0 8.0
6300 1.0 10.0 IF = 10 mA
6305 10.0 40.0
7000 Luminous Intensity[1] Iv0.4 1.0 mcd IF = 2 mA
6600 1.3 5.0 VF = 5.0 Volts
6620 0.8 2.0
6653 to 1.0 3.0 IF = 10 mA
6658
All Forward Voltage VF1.5 1.8 3.0 V IF = 10 mA
(Nonresistor Lamps)
6600 9.6 13.0
IFmA VF = 5.0 V
6620 3.5 5.0
All Reverse Breakdown VR5.0 30.0 V IR = 100 µA
Voltage
P205 125
6305 Included Angle Between 2θ1/228 Deg.
Half Intensity Points[2]
All 90
Diffused
Peak Wavelength λPEAK 635 nm Measured at Peak
Dominant Wavelength[3] λd626 nm
Spectral Line Half Width ∆λ1/2 40 nm
All Speed of Response τs90 ns
Capacitance C 11 pF VF = 0; f = 1 MHz
Thermal Resistance RθJ-PIN 170 °C/W Junction-to-Cathode
Lead
Luminous Efficacy[4] ηv145 lm/W
High Efficiency Red
Forward Current
(Resistor Lamps)
8
Device
HLMP- Parameter Symbol Min. Typ. Max. Units Test Conditions
P402 1.0 4.0
P405 Luminous Intensity Iv1.0 6 mcd IF = 10 mA
Q400 1.0 8
Forward Voltage VF1.5 1.9 3.0 V IF = 10 mA
All Reverse Breakdown VR5.0 30.0 V IR = 100 µA
Voltage
P405 Included Angle Between 125
Half Intensity Points[2] 2θ1/2Deg.
Q400 90
Peak Wavelength λPEAK 600 nm
Dominant Wavelength[3] λd602 nm Measured at Peak
Spectral Line Half Width ∆λ1/2 40 nm
All Speed of Response τs260 ns
Capacitance C 4 pF VF = 0; f = 1 MHz
Thermal Resistance RθJ-PIN 170 °C/W Junction-to-Cathode
Lead
Luminous Efficacy[4] ηv380 lm/W
Orange
9
Yellow
Device
HLMP- Parameter Symbol Min. Typ. Max. Units Test Conditions
P302 1.0 3.0
P305 1.0 4.0 IF = 10 mA
6400 1.0 9.0
6405 Luminous Intensity[1] Iv3.6 20 mcd
7019 0.4 0.6 IF = 2 mA
6700 1.4 5.0 VF = 5.0 Volts
6720 0.9 2.0
6753 to 1.0 3.0 IF = 10 mA
6758
All Forward Voltage VF2.0 2.4 V IF = 10 mA
(Nonresistor Lamps)
6700 9.6 13.0
Forward Current IFmA VF = 5.0 V
6720 (Resistor Lamps) 3.5 5.0
All Reverse Breakdown VR5.0 50.0 V
Voltage
P305 125
6405 Included Angle Between 2θ1/228 Deg.
Half Intensity Points[2]
All 90
Diffused
Peak Wavelength λPEAK 583 nm Measured at Peak
Dominant Wavelength[3] λd585 nm
Spectral Line Half Width ∆λ1/2 36 nm
All Speed of Response τs90 ns
Capacitance C 15 pF VF = 0; f = 1 MHz
Thermal Resistance RθJ-PIN 170 °C/W Junction-to-Cathode
Lead
Luminous Efficacy[4] ηv500 lm/W
10
High Performance Green
Device
HLMP- Parameter Symbol Min. Typ. Max. Units Test Conditions
P502 1.0 3.0
P505 1.6 6.3
6500 1.0 7.0 IF = 10 mA
6505 10.0 40.0
7040 Luminous Intensity[1] Iv0.4 0.6 mcd IF = 2 mA
6800 1.6 5.0 VF = 5.0 Volts
6820 0.8 2.0
6853 to 1.0 3.0 IF = 10 mA
6858
All Forward Voltage VF2.1 2.7 V IF = 10 mA
(Nonresistor Lamps)
6800 9.6 13.0
Forward Current IFmA VF = 5.0 V
6820 (Resistor Lamps) 3.5 5.0
All Reverse Breakdown VR5.0 50.0 V IR = 100 µA
Voltage
P505 125
6505 Included Angle Between 2θ1/228 Deg.
Half Intensity Points[2]
All 90
Diffused
Peak Wavelength λPEAK 565 nm
Dominant Wavelength[3] λd569 nm
Spectral Line Half Width ∆λ1/2 28 nm
All Speed of Response τs500 ns
Capacitance C 18 pF VF = 0; f = 1 MHz
Thermal Resistance RθJ-PIN 170 °C/W Junction-to-Cathode
Lead
Luminous Efficacy[4] ηv595 lm/W
Notes:
1. The luminous intensity for arrays is tested to assure a 2.1 to 1.0 matching between elements. The average luminous intensity for an
array determines its light output category bin. Arrays are binned for luminous intensity to allow Iv matching between arrays.
2. θ1/2 is the off-axis angle where the luminous intensity is half the on-axis value.
3. Dominant wavelength, λd, is derived from the CIE Chromaticity Diagram and represents the single wavelength that defines the color of
the device.
4. Radiant intensity, Ie, in watts/steradian, may be calculated from the equation Ie =Iv/ηv, where Iv is the luminous intensity in
candelas and ηv is the luminous efficacy in lumens/watt.
11
Device
HLMP- Parameter Symbol Min. Typ. Max. Units Test Conditions
P605 Luminous Intensity Iv1.0 1.5 mcd IF = 10 mA
Q600 1.0 1.5
Forward Voltage VF2.2 3.0 V IF = 10 mA
Reverse Breakdown VR5.0 V IR = 100 µA
Voltage
P605 Included Angle Between 125
Half Intensity Points[2] 2θ1/2Deg.
Q600 90
Peak Wavelength λPEAK 558 nm
Dominant Wavelength[3] λd560 nm Measured at Peak
Spectral Line Half Width ∆λ1/2 24 nm
P605/
Q600 Speed of Response τs3100 ns
Capacitance C 35 pF VF = 0; f = 1 MHz
Thermal Resistance RθJ-PIN 170 °C/W Junction-to-Cathode
Lead
Luminous Efficacy[4] ηv656 lm/W
Emerald Green[1]
Note:
1. Please refer to Application Note 1061 for information comparing standard green and emerald green light ouptut degradation.
12
Standard Red, DH As AlGaAs Red
Standard Red and DH AS
AlGaAs Red
High Efficiency Red, Orange,
Yellow, and High
Performance Green
HER, Orange, Yellow, and
High Performance Green,
and Emerald Green
Low Current
Figure 1. Relative Intensity vs. Wavelength.
Figure 2. Forward Current vs. Forward Voltage. (Non-Resistor Lamp)
Figure 3. Relative Luminous Intensity vs. Forward Current. (Non-Resistor Lamp)
13
Figure 4. Relative Efficiency (Luminous Intensity per Unit Current) vs. Peak Current (Non-Resistor Lamps).
Figure 5. Maximum Forward dc Current vs. Ambient Temperature. Derating Based on TJ MAX = 110 °C (Non-
Resistor Lamps).
Figure 6. Maximum Tolerable Peak Current vs. Pulse Duration. (IDC MAX as per MAX Ratings) (Non-Resistor Lamps).
Standard Red
DH As AlGaAs RedStandard Red
HER, Orange, Yellow, and High
Performance Green DH As AlGaAs Red
HER, Orange, Yellow, and
High Performance Green,
and Emerald Green
14
Figure 9. Relative Intensity vs. Angular Displacement.
Figure 7. Resistor Lamp Forward Current vs. Forward
Voltage. Figure 8. Resistor Lamp Luminous Intensity vs.
Forward Voltage.
15
www.semiconductor.agilent.com
Data subject to change.
Copyright © 1999 Agilent Technologies
Obsoletes 5968-2537E (2/96)
5968-7825E (11/99)
