LM2853 LM2853 3A 550 kHz Synchronous SIMPLE SWITCHER(R) Buck Regulator Literature Number: SNVS459 LM2853 3A 550 kHz Synchronous SIMPLE SWITCHER (R) Buck Regulator General Description Features SWITCHER (R) The LM2853 synchronous SIMPLE buck regulator is a 550 kHz step-down switching voltage regulator capable of driving up to a 3A load with excellent line and load regulation. The LM2853 accepts an input voltage between 3.0V and 5.5V and delivers a customizable output voltage that is factory programmable from 0.8V to 3.3V in 100mV increments. Internal type-three compensation enables a low component count solution and greatly simplifies external component selection. The exposed-pad TSSOP-14 package enhances the thermal performance of the LM2853. n Input voltage range of 3.0V to 5.5V n Factory EEPROM set output voltages from 0.8V to 3.3V in 100 mV increments n Maximum load current of 3A n Voltage Mode Control n Internal type-three compensation n Switching frequency of 550 kHz n Low standby current of 12 A n Internal 40 m MOSFET switches n Standard voltage options 0.8/1.0/1.2/1.5/1.8/2.5/3.0/3.3 volts n Exposed pad TSSOP-14 package Applications n Low voltage point of load regulation n Local solution for FPGA/DSP/ASIC core power n Broadband networking and communications infrastructure Typical Application Circuit 20201502 Efficiency vs Load Current (VOUT = 3.3V) 20201501 SIMPLE SWITCHER (R) is a Registered Trademark of National Semiconductor Corporation. (c) 2006 National Semiconductor Corporation DS202015 www.national.com LM2853 3A 550 kHz Synchronous SIMPLE SWITCHER (R) Buck Regulator October 2006 LM2853 Connection Diagram 20201503 Ordering Information Order Number LM2853MH-0.8 LM2853MHX-0.8 LM2853MH-1.0 LM2853MHX-1.0 LM2853MH-1.2 LM2853MHX-1.2 LM2853MH-1.5 LM2853MHX-1.5 LM2853MH-1.8 LM2853MHX-1.8 LM2853MH-2.5 LM2853MHX-2.5 LM2853MH-3.0 LM2853MHX-3.0 LM2853MH-3.3 LM2853MHX-3.3 Voltage Option Package Marking 0.8 LM2853-0.8 1.0 LM2853-1.0 1.2 LM2853-1.2 1.5 LM2853-1.5 1.8 LM2853-1.8 2.5 LM2853-2.5 3.0 LM2853-3.0 3.3 LM2853-3.3 Package Type Package Drawing Supplied As 94 Units, Rail 2500 Units, Tape and Reel 94 Units, Rail 2500 Units, Tape and Reel 94 Units, Rail 2500 Units, Tape and Reel 94 Units, Rail TSSOP-14 exposed pad MXA14A 2500 Units, Tape and Reel 94 Units, Rail 2500 Units, Tape and Reel 94 Units, Rail 2500 Units, Tape and Reel 94 Units, Rail 2500 Units, Tape and Reel 94 Units, Rail 2500 Units, Tape and Reel Note: Contact factory for other voltage options. Pin Descriptions Pin # Name 1 AVIN 2 EN 3 SGND Enable. Low noise ground. 4 SS Soft-Start Pin. 5 NC No Connect. This pin must be tied to ground. 6,7 PVIN 8,9 SW 10,11 PGND 12,13 NC 14 SNS Exposed Pad EP www.national.com Function Input Voltage for Control Circuitry. Input Voltage for Power Circuitry. Switch Pin. Power Ground. No-Connect. These pins must be tied to ground. Output Voltage Sense Pin. The exposed pad is internally connected to GND, but it cannot be used as the primary GND connection. The exposed pad should be soldered to an external GND plane. 2 14-Pin Exposed Pad TSSOP Package If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. AVIN, PVIN, EN, SNS, SW, SS Infrared (15 sec) 220C Vapor Phase (60 sec) 215C Soldering (10 sec) 260C -0.3V to 6.0V ESD Susceptibility (Note 2) 2kV Operating Ratings (Note 1) Power Dissipation Internally Limited Storage Temperature Range -65C to +150C PVIN to GND 150C AVIN to GND Maximum Junction Temp. 1.5V to 5.5V 3.0V to 5.5V Junction Temperature -40C to +125C Electrical Characteristics Specifications with standard typeface are for TJ = 25C, and those in bold face type apply over the full Junction Temperature Range (-40C to 125C). Minimum and Maximum limits are guaranteed through test, design or statistical correlation. Typical values represent the most likely parametric norm at TJ = 25C and are provided for reference purposes only. Unless otherwise specified AVIN = PVIN = 5V. Symbol Parameter Conditions Min Typ Max VOUT = 0.8V option 0.782 0.8 0.818 VOUT = 1.0V option 0.9775 1.0 1.0225 VOUT = 1.2V option 1.1730 1.2 1.227 Units SYSTEM PARAMETERS VOUT VOUT/AVIN Voltage Tolerance (Note 3) Line Regulation (Note 3) VOUT = 1.5V option 1.4663 1.5 1.5337 VOUT = 1.8V option 1.7595 1.8 1.8405 VOUT = 2.5V option 2.4437 2.5 2.5563 VOUT = 3.0V option 2.9325 3.0 3.0675 VOUT = 3.3V option 3.2257 V 3.3 3.3743 VOUT = 0.8V, 1.0V, 1.2V, 1.5V, 1.8V or 2.5V 3.0V AVIN 5.5V 0.2 1.1 % VOUT = 3.0V or 3.3V 3.5V AVIN 5.5V 0.2 1.1 % VOUT/IO Load Regulation Normal operation VON UVLO Threshold (AVIN) Rising Falling Hysteresis RDS(ON)-P PFET On Resistance Isw = 3A RDS(ON)-N NFET On Resistance Isw = 3A RSS Soft-Start Resistance ICL Peak Current Limit Threshold IQ Operating Current Non-switching ISD Shutdown Quiescent Current EN = 0V RSNS Sense Pin Resistance 2 50 3.6 mV/A 2.47 3.0 V 155 260 mV 40 120 m 32 100 m 450 k 5 A 0.85 2 12 50 432 mA A k PWM fosc Switching Frequency Drange Duty Cycle Range . 325 550 0 725 kHz 100 % ENABLE CONTROL (Note 4) VIH EN Pin Minimum High Input VIL EN Pin Maximum Low Input IEN EN Pin Pullup Current 75 % of AVIN 25 EN = 0V 1.5 3 % of AVIN A www.national.com LM2853 Absolute Maximum Ratings (Note 1) LM2853 Electrical Characteristics Specifications with standard typeface are for TJ = 25C, and those in bold face type apply over the full Junction Temperature Range (-40C to 125C). Minimum and Maximum limits are guaranteed through test, design or statistical correlation. Typical values represent the most likely parametric norm at TJ = 25C and are provided for reference purposes only. Unless otherwise specified AVIN = PVIN = 5V. (Continued) Symbol Parameter Conditions Min Typ Max Units THERMAL CONTROLS TSD Thermal Shutdown Threshold 165 C TSD-HYS Hysteresis for Thermal Shutdown 10 C 38 C/W THERMAL RESISTANCE JA Junction to Ambient MXA14A Note 1: Absolute maximum ratings indicate limits beyond which damage to the device may occur. Operating Range indicates conditions for which the device is intended to be functional, but does not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. Note 2: The human body model is a 100 pF capacitor discharged through a 1.5 k resistor into each pin. Test Method is per JESD22-AI14. Note 3: VOUT measured in a non-switching, closed-loop configuration at the SNS pin. Note 4: The enable pin is internally pulled up, so the LM2853 is automatically enabled unless an external enable voltage is applied. www.national.com 4 Unless otherwise specified, the following conditions apply: VIN = AVIN = PVIN = 5V, TJ = 25C. Efficiency vs. ILOAD VOUT = 1.8V NFET RDS(ON) vs. Temperature 20201507 20201505 Efficiency vs. ILOAD VOUT = 2.5V PFET RDS(ON) vs. Temperature 20201509 20201504 Efficiency vs. ILOAD VOUT = 3.3V Switching Frequency vs. Temperature 20201508 20201506 5 www.national.com LM2853 Typical Performance Characteristics LM2853 Typical Performance Characteristics Unless otherwise specified, the following conditions apply: VIN = AVIN = PVIN = 5V, TJ = 25C. (Continued) IQ vs. VIN and Temperature ISD vs. VIN and Temperature 20201510 www.national.com 20201511 6 LM2853 Block Diagram 20201512 Applications Information load regulation and transient performance, the use of a small 1 F ceramic capacitor is also recommended as a local bypass for the AVIN pin. The LM2853 is a DC-DC buck regulator belonging to National Semiconductor's synchronous SIMPLE SWITCHER (R) family. Integration of the PWM controller, power switches and compensation network greatly reduces the component count required to implement a switching power supply. A typical application requires only four components: an input capacitor, a soft-start capacitor, an output filter capacitor and an output filter inductor. SOFT-START CAPACITOR (CSS) The DAC that sets the reference voltage of the error amplifier sources a current through a resistor to set the reference voltage. The reference voltage is one half of the output voltage of the switcher due to the 200 k divider connected to the SNS pin. Upon start-up, the output voltage of the switcher tracks the reference voltage with a two to one ratio as the DAC current charges the capacitance connected to the reference voltage node. Internal capacitance of 20 pF is permanently attached to the reference voltage node which is also connected to the soft start pin, SS. Adding a soft-start capacitor externally increases the time it takes for the output voltage to reach its final level. The charging time required for the reference voltage can be estimated using the RC time constant of the DAC resistor and the capacitance connected to the SS pin. Three RC time constant periods are needed for the reference voltage to reach 95% of its final value. The actual start up time will vary with differences in the DAC resistance and higher-order effects. If little or no soft-start capacitance is connected, then the start up time may be determined by the time required for the current limit current to charge the output filter capacitance. The capacitor charging equation I = CV/t can be used to estimate the start-up time in this case. For example, a part with a 3V output, a 100 F output capacitance and a 5A current limit threshold would require a time of 60 s: INPUT CAPACITOR (CIN) Fast switching of large currents in the buck converter places a heavy demand on the voltage source supplying PVIN. The input capacitor, CIN, supplies extra charge when the switcher needs to draw a burst of current from the supply. The RMS current rating and the voltage rating of the CIN capacitor are therefore important in the selection of CIN. The RMS current specification can be approximated by: where D is the duty cycle, VOUT/VIN. CIN also provides filtering of the supply. Trace resistance and inductance degrade the benefits of the input capacitor, so CIN should be placed very close to PVIN in the layout. A 22 F or 47 F ceramic capacitor is typically sufficient for CIN. In parallel with the large input capacitance a smaller capacitor should be added such as a 1 F ceramic for higher frequency filtering. Ceramic capacitors with high quality dielectrics such as X5R or X7R should be used to provide a constant capacitance across temperature and line variations. For improved 7 www.national.com LM2853 Applications Information voltage the output reached during the short circuit event. The range of soft-start capacitors is therefore restricted to values 1 nF to 50 nF. (Continued) COMPENSATION The LM2853 provides a highly integrated solution to power supply design. The compensation of the LM2853, which is type-three, is included on-chip. The benefit of integrated compensation is straight-forward, simple power supply design. Since the output filter capacitor and inductor values impact the compensation of the control loop, the range of LO, CO and CESR values is restricted in order to ensure stability. Since it is undesirable for the power supply to start up in current limit, a soft-start capacitor must be chosen to force the LM2853 to start up in a more controlled fashion based on the charging of the soft-start capacitance. In this example, suppose a 3 ms start time is desired. Three time constants are required for charging the soft-start capacitor to 95% of the final reference voltage. So in this case RC = 1 ms. The DAC resistor, R, is 450 k so C can be calculated to be 2.2 nF. A 2.2 nF ceramic capacitor can be chosen to yield approximately a 3 ms start-up time. OUTPUT FILTER VALUES Table 1 details the recommended inductor and capacitor ranges for the LM2853 that are suggested for various typical output voltages. Values slightly different than those recommended may be used, however the phase margin of the power supply may be degraded. For best performance when output voltage ripple is a concern, ESR values near the minimum of the recommended range should be paired with capacitance values near the maximum. If a minimum output voltage ripple solution from a 5V input voltage is desired, a 6.8 H inductor can be paired with a 220 F (50 m) capacitor without degraded phase margin. SOFT-START CAPACITOR (CSS) AND FAULT CONDITIONS Various fault conditions such as short circuit and UVLO of the LM2853 activate internal circuitry designed to control the voltage on the soft-start capacitor. For example, during a short circuit current limit event, the output voltage typically falls to a low voltage. During this time, the soft-start voltage is forced to track the output so that once the short is removed, the LM2853 can restart gracefully from whatever TABLE 1. Recommended LO and CO Values LO (H) CO (F) CESR (m) VOUT (V) VIN (V) Min Max Min Max Min Max 0.8 5 4.7 6.8 120 220 70 100 0.8 3.3 4.7 4.7 150 220 50 100 1 5 4.7 6.8 120 220 70 100 1 3.3 4.7 4.7 150 220 50 100 1.2 5 4.7 6.8 120 220 70 100 1.2 3.3 4.7 4.7 120 220 60 100 1.5 5 4.7 6.8 120 220 70 100 1.5 3.3 4.7 4.7 120 220 60 100 1.8 5 4.7 6.8 120 220 70 120 1.8 3.3 4.7 4.7 100 220 70 120 2.5 5 4.7 6.8 120 220 70 150 2.5 3.3 4.7 4.7 100 220 80 150 3.0 5 4.7 6.8 120 220 70 150 3.0 3.3 4.7 4.7 100 220 80 150 3.3 5 4.7 6.8 120 220 70 150 www.national.com 8 LM2853 Applications Information (Continued) CHOOSING AN INDUCTANCE VALUE The current ripple present in the output filter inductor is determined by the input voltage, output voltage, switching frequency and inductance according to the following equation: The maximum inductor current for a 3A load would therefore be 3A plus 177 mA, 3.177A. As shown in the ripple equation, the current ripple is inversely proportional to inductance. OUTPUT FILTER INDUCTORS Once the inductance value is chosen, the key parameter for selecting the output filter inductor is its saturation current (ISAT) specification. Typically ISAT is given by the manufacturer as the current at which the inductance of the coil falls to a certain percentage of the nominal inductance. The ISAT of an inductor used in an application should be greater than the maximum expected inductor current to avoid saturation. Below is a table of inductors that are suitable in LM2853 applications. where IL is the peak to peak current ripple, D is the duty cycle VOUT/VIN, VIN is the input voltage applied to the output stage, VOUT is the output voltage of the switcher, f is the switching frequency and LO is the inductance of the output filter inductor. Knowing the current ripple is important for inductor selection since the peak current through the inductor is the load current plus one half the ripple current. Care must be taken to ensure the peak inductor current does not reach a level high enough to trip the current limit circuitry of the LM2853. As an example, consider a 5V to 1.2V conversion and a 550 kHz switching frequency. According to Table 1, a 4.7 H inductor may be used. Calculating the expected peak-to-peak ripple, TABLE 2. Recommended Inductors Inductance Part Number Vendor 4.7 F DO3308P-472ML Coilcraft 4.7 F DO3316P-472ML Coilcraft 4.7 F MSS1260-472ML Coilcraft 5.2 F MSS1038-522NL Coilcraft 5.6 F MSS1260-562ML Coilcraft 6.8 F DO3316P-682ML Coilcraft 6.8 F MSS1260-682ML Coilcraft OUTPUT FILTER CAPACITORS The recommended capacitors that may be used in the output filter with the LM2853 are limited in value and ESR range according to Table 1. Below are some examples of capacitors that can typically be used in an LM2853 application. TABLE 3. Recommended Capacitors Capacitance (F) Part Number Chemistry Vendor 100 594D107X_010C2T Tantalum Vishay-Sprague 100 593D107X_010D2_E3 Tantalum Vishay-Sprague 100 TPSC107M006#0075 Tantalum AVX 100 NOSD107M006#0080 Niobium Oxide AVX 100 NOSC107M004#0070 Niobium Oxide AVX 120 594D127X_6R3C2T Tantalum Vishay-Sprague 150 594D157X_010C2T Tantalum Vishay-Sprague 150 595D157X_010D2T Tantalum Vishay-Sprague 150 591D157X_6R3C2_20H Tantalum Vishay-Sprague 150 TPSD157M006#0050 Tantalum AVX AVX 150 TPSC157M004#0070 Tantalum 150 NOSD157M006#0070 Niobium Oxide AVX 220 594D227X_6R3D2T Tantalum Vishay-Sprague 220 591D227X_6R3D2_20H Tantalum Vishay-Sprague 220 591D227X_010D2_20H Tantalum Vishay-Sprague 220 593D227X_6R3D2_E3 Tantalum Vishay-Sprague 9 www.national.com LM2853 Applications Information (Continued) TABLE 3. Recommended Capacitors (Continued) Capacitance (F) Part Number Chemistry 220 TPSD227M006#0050 Tantalum AVX 220 NOSD227M0040060 Niobium Oxide AVX SPLIT-RAIL OPERATION Vendor components need to be chosen based on the value of PVIN. For PVIN levels lower than 3.3V, use output filter component values recommended for 3.3V. PVIN must always be equal to or less than AVIN. The LM2853 can be powered using two separate voltages for AVIN and PVIN. AVIN is the supply for the control logic; PVIN is the supply for the power FETs. The output filter 20201513 SWITCH NODE PROTECTION The LM2853 includes protection circuitry that monitors the voltage on the switch pin. Under certain fault conditions, switching is disabled in order to protect the switching devices. One side effect of the protection circuitry may be observed when power to the LM2853 is applied with no or light load on the output. The output will regulate to the rated voltage, but no switching may be observed. As soon as the output is loaded, the LM2853 will begin normal switching operation. tween all ground connections. 3. The sense pin connection should be made as close to the load as possible so that the voltage at the load is the expected regulated value. The sense line should not run too close to nodes with high dV/dt or dl/dt (such as the switch node) to minimize interference. 4. The switch node connections should be low resistance to reduce power losses. Low resistance means the trace between the switch pin and the inductor should be wide. However, the area of the switch node should not be too large since EMI increases with greater area. So connect the inductor to the switch pin with a short, but wide trace. Other high current connections in the application such as PVIN and VOUT assume the same trade off between low resistance and EMI. LAYOUT GUIDELINES These are several guidelines to follow while designing the PCB layout for an LM2853 application. 1. The input bulk capacitor, CIN, should be placed very close to the PVIN pin to keep the resistance as low as possible between the capacitor and the pin. High current levels will be present in this connection. 2. All ground connections must be tied together. Use a broad ground plane, for example a completely filled back plane, to establish the lowest resistance possible be- 5. Allow area under the chip to solder the entire exposed die attach pad to ground for improved thermal performance. Lab measurements also show improved regulation performance when the exposed pad is well grounded. LM2853 Example Circuit Schematic 20201514 FIGURE 1. www.national.com 10 LM2853 LM2853 Example Circuit Schematic (Continued) Bill of Materials for 5V to 3.3V Conversion ID Part Number Type Size Parameters Qty U1 LM2853MH-3.3 3A Buck ETSSOP-14 3.3V 1 Vendor NSC CIN GRM31CR60J476ME19 Capacitor 1206 47 F 1 Murata CBYP GRM21BR71C105KA01 Capacitor 0805 1 F 1 Murata CSS VJ0805Y222KXXA Capacitor 0603 2.2 nF 1 Vishay-Vitramon LO DO3316P-682 Inductor DO3316P 6.8 H 1 Coilcraft CO 594D127X06R3C2T Capacitor C Case 120F (85m) 1 Vishay-Sprague Bill of Materials for 3.3V to 1.2V Conversion ID Part Number Type Size Parameters Qty Vendor U1 LM2853MH-1.2 3A Buck ETSSOP-14 1.2V 1 NSC CIN GRM31CR60J476ME19 Capacitor 1206 47 F 1 Murata CBYP GRM21BR71C105KA01 Capacitor 0805 1 F 1 Murata CSS VJ0805Y222KXXA Capacitor 0603 2.2 nF 1 Vishay-Vitramon LO DO3316P-472 Inductor DO3316P 4.7 H 1 Coilcraft CO NOSD157M006R0070 Capacitor D Case 150 F (70 m) 1 AVX 11 www.national.com LM2853 3A 550 kHz Synchronous SIMPLE SWITCHER (R) Buck Regulator Physical Dimensions inches (millimeters) unless otherwise noted 14-Lead ETSSOP Package NS Package Number MXA14A National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor follows the provisions of the Product Stewardship Guide for Customers (CSP-9-111C2) and Banned Substances and Materials of Interest Specification (CSP-9-111S2) for regulatory environmental compliance. Details may be found at: www.national.com/quality/green. Lead free products are RoHS compliant. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated