INCH-POUND MIL-DTL-24308/2T w/AMENDMENT 1 28 June 2012 SUPERSEDING MIL-DTL-24308/2T 2 March 2009 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRIC, RECTANGULAR, MINIATURE, POLARIZED SHELL, RACK AND PANEL, RECEPTACLE, SOCKET CONTACTS, GENERAL PURPOSE, CLASS D AND G, CRIMP TYPE This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-24308. FIGURE 1. Shell, receptacle, crimp type. AMSC N/A FSC 5935 Source: http://assist.dla.mil -- Downloaded: 2021-01-21T07:51Z Check the source to verify that this is the current version before use. MIL-DTL-24308/2T w/AMENDMENT 1 Detail (See note10) Shell size 1 2 3 A 4 5 6 1 Dimensions A B C D E F G 1.228 .648 .989 .316 .509 .439 .248 (31.19) (16.46) (25.12) ( 8.03) (12.93) (11.15) (6.30) 1.198 .638 .979 .302 .479 .419 .238 (30.43) (16.21) (24.87) ( 7.67) (12.17) (10.64) (6.05) 1.556 .976 1.317 .316 .509 .439 .248 (39.52) (24.79) (33.45) ( 8.03) (12.93) (11.15) (6.30) 1.526 .966 1.307 .302 .479 .419 .238 (38.76) (24.54) (33.20) ( 7.67) (12.17) (10.64) (6.05) 2.103 1.516 1.857 .316 .509 .439 .248 (53.42) (38.51) (47.17) ( 8.03) (12.93) (11.15) (6.30) 2.073 1.506 1.847 .302 .479 .419 .238 (52.65) (38.25) (46.91) ( 7.67) (12.17) (10.64) (6.05) 2.744 2.164 2.505 .316 .509 .439 .248 (69.70) (54.97) (63.63) ( 8.03) (12.93) (11.15) (6.30) 2.714 2.154 2.495 .302 .479 .419 .238 (68.94) (54.71) (63.37) ( 7.67) (12.17) (10.64) (6.05) 2.650 2.069 2.411 .428 .620 .439 .248 (67.31) (52.55) (61.24) (10.87) (15.75) (11.15) (6.30) 2.620 2.059 2.401 .418 .590 .419 .238 (66.55) (52.30) (60.99) (10.62) (14.99) (10.64) (6.05) 2.744 2.194 2.505 .490 .683 .439 .248 (69.70) (55.73) (63.63) (12.45) (17.35) (11.15) (6.30) 2.714 2.184 2.495 .480 .653 .419 .238 (68.94) (55.47) (63.37) (12.19) (16.59) (10.64) (6.05) Same as detail A, shell size 1 except in accordance with detail B. 2 Same as detail A, shell size 2 except in accordance with detail B. B 3 Same as detail A, shell size 3 except in accordance with detail B. (See note 11) 4 Same as detail A, shell size 4 except in accordance with detail B. 5 Same as detail A, shell size 5 except in accordance with detail B. 6 Same as detail A, shell size 6 except in accordance with detail B. 1 Same as detail A, shell size 1 except in accordance with detail C. 2 Same as detail A, shell size 2 except in accordance with detail C. C 3 Same as detail A, shell size 3 except in accordance with detail C. (See note 11) 4 Same as detail A, shell size 4 except in accordance with detail C. 5 Same as detail A, shell size 5 except in accordance with detail C. 6 Same as detail A, shell size 6 except in accordance with detail C. 1 Same as detail A, shell size 1 except in accordance with detail D. 2 Same as detail A, shell size 2 except in accordance with detail D. 3 Same as detail A, shell size 3 except in accordance with detail D. 4 Same as detail A, shell size 4 except in accordance with detail D. 5 Same as detail A, shell size 5 except in accordance with detail D. 6 Same as detail A, shell size 6 except in accordance with detail D. D H .769 (19.53) .749 (19.02) 1.093 (27.76) 1.073 (27.25) 1.635 (41.53) 1.615 (41.02) 2.282 (57.96) 2.262 (57.45) 2.188 (55.58) 2.168 (55.07) 2.312 (58.72) 2.292 (58.22) FIGURE 1. Shell, receptacle, crimp type - Continued. 2 Source: http://assist.dla.mil -- Downloaded: 2021-01-21T07:51Z Check the source to verify that this is the current version before use. J .432 (10.97) .412 (10.46) .432 (10.97) .412 (10.46) .432 (10.97) .412 (10.46) .432 (10.97) .412 (10.46) .544 (13.82) .524 (13.31) .606 (15.39) .586 (14.88) K .060 (1.52) .035 (.89) .060 (1.52) .035 (.89) .060 (1.52) .035 (.89) .060 (1.52) .035 (.89) .060 (1.52) .035 (.89) .060 (1.52) .035 (.89) L .040 (1.02) .020 (.51) .040 (1.02) .020 (.51) .049 (1.25) .029 (.74) .049 (1.25) .029 (.74) .049 (1.25) .029 (.74) .049 (1.25) .029 (.74) MIL-DTL-24308/2T w/AMENDMENT 1 NOTES: 1. 2. 3. 4. Dimensions are in inches. Metric equivalents are given for information only. Insulator may project .375 (9.53) maximum. Wire insulation .072 (1.83) maximum for arrangements, (see MIL-DTL-24308, Appendix A), A-1-1, A-2-1, A-3-1, A-4-1,and A-5-1. Wire insulation .054 (1.37) maximum for arrangements, (see MIL-DTL-24308, Appendix A),A-1-2, A-2-2, A-3-2, A-4-2, A-5-2, and A-6-1. 5. To accommodate a .040 (1.02) diameter pin for arrangements, (see MIL-DTL-24308, Appendix A), A-1-1, A-2-1, A-3-1, A-4-1, and A-5-1. To accommodate a .030 (.76) diameter pin for arrangements, (see MIL-DTL-24308, Appendix A),A-1-2, A-2-2, A-3-2, A-4-2, A-5-2, and A-6-1. 6. Use .041/.039 (1.04/.99) diameter pin for arrangements, (see MIL-DTL-24308, Appendix A),A-1.1, A2.1, A-3.1, A-4.1,and A-5.1. Use .0305/.0295 (.77/.75) diameter pin for arrangements, (see MIL-DTL-24308, Appendix A), A-1-2, A-2-2, A-3-2, A-4-2, A-5-2, and A-6-1. 7. Patent notice. The government has a royalty free license under the U.S. Patents listed below for the benefit of manufacturers of the items disclosed and described herein, either for the government of for use in equipment delivered to the government. 2790153 expires April 23, 1974 3110093 expires November 12, 1980 3158424 expires November 24, 1981 8. Copyright notice. All information disclosed in this military specification sheet which is or may be copyrighted by ITT Cannon Electric is reproduced herein with the express permission of the copyright owner. 9. Indentation on the ends of the termination side of the shell, for the purpose of securing the insulator in the shell, is permitted. This may result in the "F" dimension being undersized in these areas. However the "F" dimension shall be maintained for the remainder of the connector. 10. See table II for supersession data. 11. Details B and C are inactive for new design, use detail D. Inches .004 .005 .008 .010 .031 .040 .041 .062 .070 .086 .092 .097 .103 .115 .120 .125 .129 .143 .375 mm .10 .13 .20 .25 .79 1.02 1.04 1.57 1.78 2.18 2.34 2.46 2.62 2.92 3.05 3.18 3.28 3.63 9.53 FIGURE 1. Shell, receptacle, crimp type - Continued. 3 Source: http://assist.dla.mil -- Downloaded: 2021-01-21T07:51Z Check the source to verify that this is the current version before use. MIL-DTL-24308/2T w/AMENDMENT 1 REQUIREMENTS: The connectors shall conform to figure 1 and the specification Part or Identifying Numbers (PIN) indicated in table I. TABLE I. Design standards. 1/ (PIN) Class G PIN Class D Shell size Shell detail (see figure1) A Insert arrangement reference number 6/ A-1-1 M24308/2-1 M24308/2-516 1 M24308/2-2 M24308/2-517 M24308/2-3 M24308/2-518 M39029/63-368 M24308/2-1 M24308/2-516 2 A A-2-1 M39029/63-368 M24308/2-2 M24308/2-517 3 A A-3-1 M39029/63-368 M24308/2-3 M24308/2-518 M24308/2-4 M24308/2-519 4 A A-4-1 M39029/63-368 M24308/2-4 M24308/2-519 M24308/2-5 M24308/2-520 5 A A-5-1 M39029/63-368 M24308/2-5 M24308/2-520 M24308/2-6 M24308/2-521 Connector kit: M24308/2-1 connector with applicable tool 2/ M24308/2-1 M24308/2-516 M24308/2-7 M24308/2-522 Connector kit: M24308/2-2 connector with applicable tool 2/ M24308/2-2 M24308/2-517 M24308/2-8 M24308/2-523 Connector kit: M24308/2-3 connector with applicable tool 2/ M24308/2-3 M24308/2-518 M24308/2-9 M24308/2-524 Connector kit: M24308/2-4 connector with applicable tool 2/ M24308/2-10 M24308/2-525 Connector kit: M24308/2-5 connector with applicable tool 2/ M24308/2-11 M24308/2-526 1 A A-1-2 M39029/57-354 M24308/2-4 M24308/2-519 M24308/2-5 M24308/2-520 M24308/2-11 M24308/2-526 M24308/2-12 M24308/2-527 2 A A-2-2 M39029/57-354 M24308/2-12 M24308/2-527 M24308/2-13 M24308/2-528 3 A A-3-2 M39029/57-354 M24308/2-13 M24308/2-528 M24308/2-14 M24308/2-529 4 A A-4-2 M39029/57-354 M24308/2-14 M24308/2-529 M24308/2-15 M24308/2-530 5 A A-5-2 M39029/57-354 M24308/2-15 M24308/2-530 M24308/2-16 M24308/2-531 6 A A-6-1 M39029/57-354 M24308/2-16 M24308/2-531 M24308/2-11 connector with applicable tool M24308/2-11 M24308/2-526 M24308/2-12 connector with applicable tool M24308/2-12 M24308/2-527 M24308/2-13 connector with applicable tool M24308/2-13 M24308/2-528 M24308/2-14 connector with applicable tool M24308/2-14 M24308/2-529 M24308/2-15 connector with applicable tool M24308/2-15 M24308/2-530 M24308/2-16 connector with applicable tool M24308/2-16 M24308/2-531 M24308/2-17 M24308/2-532 Connector kit: 3/ M24308/2-18 M24308/2-533 Connector kit: 3/ M24308/2-19 M24308/2-534 Connector kit: 3/ M24308/2-20 M24308/2-535 Connector kit: 3/ M24308/2-21 M24308/2-536 Connector kit: 3/ M24308/2-22 M24308/2-537 Connector kit: 3/ Contact PIN PIN marked on connector class G See footnotes at end of table. 4 Source: http://assist.dla.mil -- Downloaded: 2021-01-21T07:51Z Check the source to verify that this is the current version before use. PIN marked on connector class D MIL-DTL-24308/2T w/AMENDMENT 1 TABLE I. Design standards - Continued. 1/ PIN class G PIN class D Shell size Shell detail (see figure 1) Insert arrangement reference number 6/ 4/ M24308/2-23 4/ M24308/2-538 1 B A-1-1 M39029/63-368 M24308/2-23 M24308/2-538 M24308/2-24 M24308/2-539 2 B A-2-1 M39029/63-368 M24308/2-24 M24308/2-539 M24308/2-25 M24308/2-540 3 B A-3-1 M39029/63-368 M24308/2-25 M24308/2-540 M24308/2-26 M24308/2-541 4 B A-4-1 M39029/63-368 M24308/2-26 M24308/2-541 M24308/2-27 M24308/2-542 5 B A-5-1 M39029/63-368 M24308/2-27 M24308/2-542 M24308/2-28 M24308/2-543 1 B A-1-2 M39029/57-354 M24308/2-28 M24308/2-543 M24308/2-29 M24308/2-544 2 B A-2-2 M39029/57-354 M24308/2-29 M24308/2-544 M24308/2-30 M24308/2-545 3 B A-3-2 M39029/57-354 M24308/2-30 M24308/2-545 M24308/2-31 M24308/2-546 4 B A-4-2 M39029/57-354 M24308/2-31 M24308/2-546 M24308/2-32 M24308/2-547 5 B A-5-2 M39029/57-354 M24308/2-32 M24308/2-547 M24308/2-33 M24308/2-548 6 B A-6-1 M39029/57-354 M24308/2-33 M24308/2-548 4/ M24308/2-34 M24308/2-35 M24308/2-36 M24308/2-37 M24308/2-38 M24308/2-39 M24308/2-40 M24308/2-41 M24308/2-42 M24308/2-43 M24308/2-44 Contact PIN PIN marked on connector class G PIN marked on connector class D M24308/2-549 Connector kit: M24308/2-23 connector with applicable tool 2/ M24308/2-23 M24308/2-549 M24308/2-550 Connector kit: 2/ M24308/2-551 Connector kit: 2/ M24308/2-552 Connector kit: 2/ M24308/2-553 Connector kit: 2/ M24308/2-554 Connector kit: 2/ M24308/2-555 Connector kit: 2/ M24308/2-556 Connector kit: 2/ M24308/2-557 Connector kit: 2/ M24308/2-558 Connector kit: 2/ M24308/2-559 Connector kit: 2/ M24308/2-24 connector with applicable tool M24308/2-24 M24308/2-550 M24308/2-25 connector with applicable tool M24308/2-25 M24308/2-551 M24308/2-26 connector with applicable tool M24308/2-26 M24308/2-552 M24308/2-27 connector with applicable tool M24308/2-27 M24308/2-553 M24308/2-28 connector with applicable tool M24308/2-28 M24308/2-554 M24308/2-29 connector with applicable tool M24308/2-29 M24308/2-555 M24308/2-30 connector with applicable tool M24308/2-30 M24308/2-556 M24308/2-31 connector with applicable tool M24308/2-31 M24308/2-557 M24308/2-32 connector with applicable tool M24308/2-32 M24308/2-558 M24308/2-33 connector with applicable tool M24308/2-33 M24308/2-559 See footnotes at end of table. 5 Source: http://assist.dla.mil -- Downloaded: 2021-01-21T07:51Z Check the source to verify that this is the current version before use. MIL-DTL-24308/2T w/AMENDMENT 1 TABLE I. Design standards - Continued. 1/ PIN class G PIN class D Shell size M24308/2-281 M24308/2-282 M24308/2-283 M24308/2-284 M24308/2-285 M24308/2-286 M24308/2-287 M24308/2-288 M24308/2-289 M24308/2-290 M24308/2-291 4/ M24308/2-292 M24308/2-293 M24308/2-294 M24308/2-295 M24308/2-296 M24308/2-297 M24308/2-298 M24308/2-299 M24308/2-300 M24308/2-301 M24308/2-302 M24308/2-560 M24308/2-561 M24308/2-562 M24308/2-563 M24308/2-564 M24308/2-565 M24308/2-566 M24308/2-567 M24308/2-568 M24308/2-569 M24308/2-570 4/ M24308/2-571 M24308/2-572 M24308/2-573 M24308/2-574 M24308/2-575 M24308/2-576 M24308/2-577 M24308/2-578 M24308/2-579 M24308/2-580 M24308/2-581 1 2 3 4 5 1 2 3 4 5 6 A A A A A A A A A A A A-1-1 A-2-1 A-3-1 A-4-1 A-5-1 A-1-2 A-2-2 A-3-2 A-4-2 A-5-2 A-6-1 1 2 3 4 5 1 2 3 4 5 6 B B B B B B B B B B B 4/ M24308/2-335 M24308/2-582 M24308/2-336 M24308/2-583 M24308/2-341 M24308/2-584 3 4 2 M24308/2-342 M24308/2-343 M24308/2-344 M24308/2-345 M24308/2-346 M24308/2-347 M24308/2-348 M24308/2-349 M24308/2-350 M24308/2-351 M24308/2-352 1 2 3 4 5 1 2 3 4 5 6 M24308/2-585 M24308/2-586 M24308/2-587 M24308/2-588 M24308/2-589 M24308/2-590 M24308/2-591 M24308/2-592 M24308/2-593 M24308/2-594 M24308/2-595 Shell Insert detail arrangement (see figure 1) reference number 6/ Contact PIN Contacts not included PIN marked on connector class G PIN marked on connector class D " " " " " " " " " " M24308/2-1 M24308/2-2 M24308/2-3 M24308/2-4 M24308/2-5 M24308/2-11 M24308/2-12 M24308/2-13 M24308/2-14 M24308/2-15 M24308/2-16 M24308/2-516 M24308/2-517 M24308/2-518 M24308/2-519 M24308/2-520 M24308/2-526 M24308/2-527 M24308/2-528 M24308/2-529 M24308/2-530 M24308/2-531 A-1-1 A-2-1 A-3-1 A-4-1 A-5-1 A-1-2 A-2-2 A-3-2 A-4-2 A-5-2 A-6-1 " " " " " " " " " " " M24308/2-23 M24308/2-24 M24308/2-25 M24308/2-26 M24308/2-27 M24308/2-28 M24308/2-29 M24308/2-30 M24308/2-31 M24308/2-32 M24308/2-33 M24308/2-538 M24308/2-539 M24308/2-540 M24308/2-541 M24308/2-542 M24308/2-543 M24308/2-544 M24308/2-545 M24308/2-546 M24308/2-547 M24308/2-548 C C C A-3-1 A-4-1 A-2-1 M39029/63-368 M39029/63-368 M39029/63-368 M24308/2-335 M24308/2-582 M24308/2-336 M24308/2-583 M24308/2-341 M24308/2-584 D D D D D D D D D D D A-1-1 A-2-1 A-3-1 A-4-1 A-5-1 A-1-2 A-2-2 A-3-2 A-4-2 A-5-2 A-6-1 M39029/63-368 M39029/63-368 M39029/63-368 M39029/63-368 M39029/63-368 M39029/57-354 M39029/57-354 M39029/57-354 M39029/57-354 M39029/57-354 M39029/57-354 M24308/2-342 M24308/2-343 M24308/2-344 M24308/2-345 M24308/2-346 M24308/2-347 M24308/2-348 M24308/2-349 M24308/2-350 M24308/2-351 M24308/2-352 See footnotes at end of table. 6 Source: http://assist.dla.mil -- Downloaded: 2021-01-21T07:51Z Check the source to verify that this is the current version before use. M24308/2-585 M24308/2-586 M24308/2-587 M24308/2-588 M24308/2-589 M24308/2-590 M24308/2-591 M24308/2-592 M24308/2-593 M24308/2-594 M24308/2-595 MIL-DTL-24308/2T w/AMENDMENT 1 TABLE I. Design standards - Continued. 1/ PIN class G PIN class D M24308/2-353 M24308/2-596 M24308/2-354 M24308/2-597 M24308/2-355 M24308/2-598 M24308/2-356 M24308/2-599 M24308/2-357 M24308/2-600 M24308/2-358 M24308/2-601 M24308/2-359 M24308/2-602 M24308/2-360 M24308/2-603 M24308/2-361 M24308/2-604 M24308/2-362 M24308/2-605 M24308/2-363 M24308/2-606 M24308/2-482 M24308/2-483 M24308/2-484 M24308/2-485 M24308/2-486 M24308/2-487 M24308/2-488 M24308/2-489 M24308/2-490 M24308/2-491 M24308/2-492 5/ M24308/2-509 M24308/2-510 M24308/2-515 M24308/2-607 M24308/2-608 M24308/2-609 M24308/2-610 M24308/2-611 M24308/2-612 M24308/2-613 M24308/2-614 M24308/2-615 M24308/2-616 M24308/2-617 5/ M24308/2-621 M24308/2-622 M24308/2-627 Shell size Insert Contact PIN arrangement reference number 6/ Connector kit: M24308/2-342 connector with applicable tool 2/ Connector kit: M24308/2-343 connector with applicable tool 2/ Connector kit: M24308/2-344 connector with applicable tool 2/ Connector kit: M24308/2-345 connector with applicable tool 2/ Connector kit: M24308/2-346 connector with applicable tool 2/ Connector kit: M24308/2-347 connector with applicable tool 2/ Connector kit: M24308/2-348 connector with applicable tool 2/ Connector kit: M24308/2-349 connector with applicable tool 2/ Connector kit: M24308/2-350 connector with applicable tool 2/ Connector kit: M24308/2-351 connector with applicable tool 2/ Connector kit: M24308/2-352 connector with applicable tool 2/ Contacts not 1 A-1-1 included D 2 D A-2-1 " 3 D A-3-1 " 4 D A-4-1 " 5 D A-5-1 " 1 D A-1-2 " 2 D A-2-2 " 3 D A-3-2 " 4 D A-4-2 " 5 D A-5-2 " 6 D A-6-1 " 3 4 2 Shell detail (see figure 1) D D D A-3-1 A-4-1 A-2-1 PIN marked on connector class G PIN marked on connector class D M24308/2-342 M24308/2-585 M24308/2-343 M24308/2-586 M24308/2-344 M24308/2-587 M24308/2-345 M24308/2-588 M24308/2-346 M24308/2-589 M24308/2-347 M24308/2-590 M24308/2-348 M24308/2-591 M24308/2-349 M24308/2-592 M24308/2-350 M24308/2-593 M24308/2-351 M24308/2-594 M24308/2-352 M24308/2-595 M24308/2-342 M24308/2-343 M24308/2-344 M24308/2-345 M24308/2-346 M24308/2-347 M24308/2-348 M24308/2-349 M24308/2-350 M24308/2-351 M24308/2-352 M24308/2-585 M24308/2-586 M24308/2-587 M24308/2-588 M24308/2-589 M24308/2-590 M24308/2-591 M24308/2-592 M24308/2-593 M24308/2-594 M24308/2-595 M39029/63-368 M39029/63-368 M39029/63-368 M24308/2-621 M24308/2-622 M24308/2-627 1/ These connectors mate with connectors specified in MIL-DTL- 24308/3, MIL-DTL-24308/4, MIL-DTL24308/9, and MIL-DTL-24308/24. 2/ Installation and removal tool: M81969/39-01 with plastic tips or M81969/1-02 with metal tips. For size 20 contacts, either tool shall be supplied with each individual connector. 3/ Installation and removal tool: M81969/14-01 with plastic tips or M81969/1-04 with metal tips. For size 22 contacts, either tool shall be supplied with each individual connector. 4/ PINs M24308/2-23 through M24308/2-44, M24308/2-538 through M24308/2-559 and M24308/2-292 through M24308/2-292 through M24308/2-341, M24308/2-571 through M24308/2-584 are inactive for new design. Use M24308/2-342 through M24308/2-352, and M24308/2-585 through M24308/2-595. 7 Source: http://assist.dla.mil -- Downloaded: 2021-01-21T07:51Z Check the source to verify that this is the current version before use. MIL-DTL-24308/2T w/AMENDMENT 1 TABLE I. Design standards - Continued. 1/ 5/ PINs M24308/2-509, M24308/2-510, M24308/2-515, M24308/2-621, M24308/2-622, and M24308/2627are inactive for new design. Use M24308/2-344, M24308/2-345, M24308/2-343, M24308/2-587, M24308/2-588, and M24308/2-586, respectively. 6/ For insert arrangements see MIL-DTL-24308, Appendix A. Supersession data: See table II. TABLE II. Shell supersession data. Shell detail (see figure 1) Detail A Detail B Detail C Detail D Superseded MS sheet MS18270-1 through -6 MS18270-7 through -12 MS18270-13 through -18 MS18270-19 through -24 PIN: Consists of the letter M, the basic number of the specification sheet, and a dash number compiled from the code. PIN example: M24308/2 -361 F Specification sheet number Data sheet number from table I Finish: For class G: A = Pure electrodeposited aluminum F = Cadmium K = Zinc nickel T = Nickel Fluorocarbon Polymer Z = Zinc For class D: Class D connectors have a nickel finish, no suffix is required. Amendment notations. The margins of this specification are marked with vertical lines to indicate where modifications from this amendment were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations. 8 Source: http://assist.dla.mil -- Downloaded: 2021-01-21T07:51Z Check the source to verify that this is the current version before use. MIL-DTL-24308/2T w/AMENDMENT 1 Referenced documents. In addition to MIL-DTL-24308, this document references the following: MIL-DTL-24308/3 MIL-DTL-24308/4 MIL-DTL-24308/9 MIL-DTL-24308/24 CONCLUDING MATERIAL Custodians: Army - CR Navy - EC Air Force - 85 NASA - NA DLA - CC Preparing activity: DLA - CC (Project: 5935-2011-125) Review activities: Army - AT, AV, CR4, MI Navy - AS, CG, MC, SH Air Force - 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https://assist.dla.mil. 9 Source: http://assist.dla.mil -- Downloaded: 2021-01-21T07:51Z Check the source to verify that this is the current version before use.