APL5301-32DI-TR - Anpec Electronics Corporation

Low IQ, Low Dropout 300mA Fixed Voltage Regulator

Rev. A.9 -Apr., 2003

APL5301/2

www.anpec.com.tw1

ANPEC reserves the right to make changes to improve reliability or manufacturability without notice, and advise

customers to obtain the latest version of relevant information to verify before placing orders.

Features

The APL5301/2 series are micropower, low noise, low

dropout linear regulators, which operate from 3V to

6V input voltage and deliver up to 300mA. T ypical out-

put noise is just 60uVRMS with the addition of an exter-

nal 0.33uF bypass capacitor in BP pin and typical

dropout voltage is only 260mV at 300mA loading. De-

signed for use in battery-powered system, the low 50uA

quiescent current makes it an ideal choice. Design

with an internal P-channel MOSFET pass transistor,

the APL5301/2 maintain a low supply current, inde-

pendent of the load current and dropout voltage.

Other features include reverse current protection, ther-

mal-shutdown protection, current limit protection to

ensure specified output current and controlled short-

circuit current. The APL5301/2 regulators come in a

miniature SOP-8, SOT-23, SOT-23-5, SOT-89 and

SOT-89-5 packages.

Applications

• Notebook Computer

• PDA or Portable Equipments

• Noise-Sensitive Instrumentation Systems

••

• Low Noise : 60uVRMS (100Hz to 100kHz)

••

• Low Quiescent Current : 50uA (No load)

••

• Low Dropout Voltage : 400mV

(VOUT(Nominal)=3.0V V ersion @300mA)

••

• Very low Shutdown Current : < 0.5uA

••

• Fixed Output Voltage : 1.3V ~ 5.0V

by step 0.1V increment

••

• Stable with 1uF Output Capacitor

••

• Stable with Aluminum, Tantalum or Ceramic

Capacitors .

••

• Reverse Current Protection

••

• No Protection Diodes Needed

••

• Built in Thermal Protection

••

• Built in Current Limit Protection

••

• Controlled Short Circuit Current : 50mA

••

• Fast Transient Response

••

• Short Setting Time

••

• SOP-8, SOT-23, SOT-23-5, SOT-89,

and SOT-89-5 Packages

Pin Configuration

APL5301

SOT-89 (Top View)

GND VIN VOUT

123

TAB is VIN

SOT-23 (Top View)

GND

VOUT

VIN

APL5301

VIN

GND

VOUT 1

SHDN

APL5301

SOT-23-5 (T op View)

APL5301

SOT-89-5 (T op View)

VIN

GND

VOUT

123

SHDNBP GND

Rev. A.9 - Apr., 2003

APL5301/2

www.anpec.com.tw2

Pa ckage C ode

A : SOT -23 B : S O T -2 3-5 D : S O T -89

D 5 : S O T -89 -5 K : S O P -8

Tem p. Range

C : 0 to 70 C I : -40 to 8 5 C

H andling Code

TR : Tape & R eel

Vo ltage C ode :

13 : 1.3V ~ 34 : 3.4V 5 0 : 5.0V

APL5301/2 -

H andling Code

Tem p. Range

Pa ckage C ode

Vo ltage C ode

APL5301/2

XXXXX 13 XX XX X - Date Co de ; 13 - 1.3VAP L5301/2 -13 D/K :

Product Name Marking Product Name Marking

APL5301-13A/B 317X APL5302-13A/B 327X

APL5301-14A/B 318X APL5302-14A/B 328X

APL5301-15A/B 319X APL5302-15A/B 329X

APL5301-16A/B 31AX APL5302-16A/B 32AX

APL5301-17A/B 31BX APL5302-17A/B 32BX

APL5301-18A/B 31CX APL5302-18A/B 32CX

APL5301-19A/B 31DX APL5302-19A/B 32DX

APL5301-20A/B 31EX APL5302-20A/B 32EX

APL5301-21A/B 31FX APL5302-21A/B 32FX

APL5301-22A/B 31GX APL5302-22A/B 32GX

APL5301-23A/B 31HX APL5302-23A/B 32HX

APL5301-24A/B 31IX APL5302-24A/B 32IX

APL5301-25A/B 31JX APL5302-25A/B 32JX

APL5301-26A/B 31KX APL5302-26A/B 32KX

APL5301-27A/B 31LX APL5302-27A/B 32LX

APL5301-28A/B 31MX APL5302-28A/B 32MX

APL5301-29A/B 31NX APL5302-29A/B 32NX

APL5301-30A/B 31OX APL5302-30A/B 32OX

APL5301-31A/B 31PX APL5302-31A/B 32PX

Marking Information

SOT-23 and SOT-23-5 packages

VIN

GND

VOUT

SHDN 4

Pin Configuration (Cont.)

APL5302

SOT-89 (Top View)

SOT-23 (Top View)

APL5302

Ordering and Marking Information

°°

SOP-8 (Top View)

8SHDN

VIN

VOUT

BP GND

GND

APL5301

GND VIN

VOUT

123

TAB is GND

GND

VOUT VIN

SOT-23-5 (Top View)

APL5302

Rev. A.9 - Apr., 2003

APL5301/2

www.anpec.com.tw3

Product Name Marking Product Name Marking

APL5301-32A/B 31QX APL5302-32A/B 32QX

APL5301-33A/B 31RX APL5302-33A/B 32RX

APL5301-34A/B 31SX APL5302-34A/B 32SX

APL5301-35A/B 31TX APL5302-35A/B 32TX

APL5301-48A/B 31XX APL5302-48A/B 32XX

APL5301-49A/B 31YX APL5302-49A/B 32YX

APL5301-50A/B 31ZX APL5302-50A/B 32ZX

Marking Information (Cont.)

SOT-23 and SOT-23-5 packages

Pin Description

No. Name I/O Description

IN I Sup ply volta ge in p ut .

2GND Ground pins of the circuitry, and all ground pins must be soldered

To PC B with prop er po wer diss ipa tion.

3 SHDN(Note1) I Shutdown c o ntr ol pin, low = off, h ig h = n ro ma l.

4BP

(Note1) O Bypass signal pin of the regulator.

OUT O Output pin of the regulator.

Note1 : This pin does not exist in 3-pin package.

Symbol Parameter Rating Unit

VIN, VOUT Input Voltage or Out Voltage 6 V

SHDN Shutdown Control Pin 6V

RTH,JA Thermal Resistance – Junction to Ambient 357 °C/W

PDPower Dissipati on Internally Li mit ed W

TJOperating Junction Temperature °C

Control Section 0 to 125

Power Transistor 0 to 150

TSTG Storage Temperature Range -65 to +150 °C

TLLead Temperature (Soldering, 10 second) 260 °C

Absolute Maximum Ratings

The last character “X” in the marking is for data code.

Rev. A.9 - Apr., 2003

APL5301/2

www.anpec.com.tw4

Electrical Characteristics

Unless otherwise noted these specifications apply over full temperature, VIN=3.8V, CIN=COUT=1uF, SHDN=VIN,

TJ=0 to 125°C. Typical values refer to TJ=25°C. APL5301/2

Symbol Parameter Test Conditions Min. Typ. Max. Unit

VIN Input Voltage 2.7 6 V

VOUT Output Voltage VOUT+1.0V< VCC<6.0V, 0mA< IOUT

VOUT -2%VOUT VOUT +2%V

ILIMIT Circuit Current Limit VIN=VOUT+0.5V 500 mA

ISHORT Short Current VOUT=0V 50 mA

IOUT Load Current VIN=VOUT+0.5V 300 mA

REGLINE Line Regulation VOUT+0.5V< VCC<6.0V,

IOUT=150mA 410mV

REGLOA Load Reg ul ati on VIN =VOUT+0.5V, 0mA< IOUT < IMAX 16mV

Load Transient VIN= VOUT+0.5V , IOUT=1mA-

150mA in 1us 70 150 mV

1.3V≤VOUT<1.5V 1.2 1.6

1.5V≤VOUT<2.0V 1 1.2

2.0V≤VOUT<2.5V 0.8 0.9

2.5V≤VOUT<3V 0.6 0.7

VDROP Dropout Voltage(Note2) IOUT =300mA

3V≤VOUT≤ 5V 0.4 0.5

PSRR Ripp l e Rejection F≤1kHz, 1Vpp at VIN = VOUT+1.0V 45 55 dB

No load 50 80

IQQuiescent Current IOUT=300mA 150 180 µA

Shutdown Supply

Current(Note3) Shutdown = low

IOUT=0, VCC=6.0V 0.01 1 µA

100Hz<f<100kHz, typical load,

CBP=0.1uF, COUT = 1uF 80

Noise 100Hz<f<100kHz, typical load,

CBP=0.33uF, COUT = 1uF 60 µVrms

CBP=0.1uF,COUT=1uF, no load 4

Shutdown Recovery

Delay(Note3) CBP=0.33uF,COUT=1uF, no load 13.2 ms

OTS Over Temperatur e Shutd own 150 °C

Over Temperatur e Shutd own

Hysteresis Hysteries 10 °C

TC Output Voltage Temperature

Coefficient 50 ppm/°C

COUT Output Cap aci to r 0.8 1.0 2.6 µF

ESR 0.02 0.1 1 Ohm

Shutdown Input

Threshold(Note3) VOUT+1.0V< VIN <6.0V 0.4 1.6 2.5 V

Rev. A.9 - Apr., 2003

APL5301/2

www.anpec.com.tw5

APL5301/2

Symbol Parameter Test Conditions Min. Typ. Max. Unit

ISHDN S hut down i np ut B i a s

current(Note3) VSHDN =VIN 0.01 100 nA

Input Reverse Leakage

current VOUT-VIN=0.1V 0.1 0.5 µA

Reverse Protection

Threshold 11 50 mV

Electrical Characteristics (Cont.)

Application Circuit

VOUT

VIN

GND

SHDN

VOUT

CIN

1uF off

APL5301/2

INPUT

2.7V to 6V

0.33uF

CBP

COUT

1uF

Note2 : Dropout voltage definition : VIN-VOUT when VOUT is 2% below the value of VOUT for VIN = V OUT+ 0.5V

Note3 : For 5-pin devices only.

Rev. A.9 - Apr., 2003

APL5301/2

www.anpec.com.tw6

Typical Characteristics

(All Curves are For Fix 3.3V)

100

120

140

160

0123456

Ground Pin Current vs. Input V oltage

Input V oltage (V)

Ground Pin Current vs. Load Current (uA)

IOUT=50mA

NO LOAD

0.5

1.5

2.5

3.5

0123456

Input V oltage vs. Output Voltage

Input V oltage (V)

Output V oltage (V)

100

120

140

160

0 50 100 150 200 250 300

Ground Pin Current vs. Load Current

Ground Pin Current vs. Load Current (uA)

Load Current (mA)

3.28

3.29

3.3

3.31

3.32

-40 -15 10 35 60 85

Output V oltage vs. Temperature

Temperature (°C )

Output V oltage (V)

Rev. A.9 - Apr., 2003

APL5301/2

www.anpec.com.tw7

Typical Characteristics

1.1

1.2

1.3

1.4

1.5

1.6

3.544.555.56

SHDN Threshold V oltage vs. Input V oltage

SHDN Threshold V oltage (V)

Input V oltage (V)

-80

-70

-60

-50

-40

-30

-20

-10

10 200k20 50 100 200 500 1k 2k 5k 10k 20k 50k

PSRR vs. Frequency

Frequency (HZ)

PSRR (dB)

VIN=4.3V

IOUT =50mA

COUT=1uF

CBP=0.1uF

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.8

0.9

0123456

Reverse Leakage Current vs. Output V oltage

Reverse Leakage Current (uA)

Output V oltage (V)

100

150

200

250

300

0 50 100 150 200 250 300

Dropout V oltage vs. Load Current

Load Current (mA)

Dropout V oltage (mV)

Rev. A.9 - Apr., 2003

APL5301/2

www.anpec.com.tw8

Typical Characteristics

Output Noise

Time (s)

VOUT (50uV/div)

-300u

300u

-250u

-200u

-150u

-100u

-50u

50u

100u

150u

200u

250u

010m2m 4m 6m 8m

VIN=4.3V f=100HZ-80KHZ

IOUT =50mA COUT=1uF

CBP=0.33uF

100

150

200

250

0 0.1 0.2 0.3 0.4

Output Noise vs. Bypass Capacitor

Output Noise (uV)

Bypass Capacitor (uF)

VIN=4.3V f=100HZ-80KHZ

IOUT=50mA COUT=1uF

1mA

50mA

Load-Transient Response

Output V oltage (20mV/div)

Time (100us)

VOUT

IOUT

Time (500us/div)

VOUT

VIN

IOUT=50mA

Line-Transient Response

VIN=4.3V

Output V oltage (50mV/div)

Rev. A.9 - Apr., 2003

APL5301/2

www.anpec.com.tw9

Typical Characteristics

Entering Shutdown

2.5V

Time (2ms/div)

VOUT

vSHDN

cBP=0.33uF

2.5V

Shutdown Exit Delay

Time (4ms/div)

VOUT

vSHDN

CBP=0.1uF

2.5V

Time (0.1ms/div)

VOUT

VSHDN

Shutdown Exit Delay

0.01

0.1

0 50 100 150 200 250 300

Region of Stable ESR vs. Load Current

Load Current (mA)

COUT ESR (Ω)

Stable

Region COUT=1uF

Rev. A.9 - Apr., 2003

APL5301/2

www.anpec.com.tw10

The minimum input-output voltage difference (dropout)

determines the lowest usable supply voltage. In bat-

tery-powered systems, this will determine the useful

end-of-life battery voltage. Because the APL5301/2

use a p-channel MOSFET pass transistor, the drop-

out voltage is a function of drain-to-source on-resis-

tance (RDS(ON)) multiplied by the load current.

The APL5301/2 load-transient response graphs in typi-

cal characteristics show the transient response. A

step change in the load current from 1mA to 50mA at

1us will cause a 60mV transient spike. Larger output

capacitor and lower ESR can reduce transient spike.

Application Information

Capacitor Selection and Regulator

Stability

The APL5301/2 use at least a 1uF capacitor on the

input, and this capacitor can be Aluminum, Tantalum

or Ceramic capacitor. The input capacitor with larger

value and lower ESR provides better PSRR and line-

transient response. The output capacitor also can use

Aluminum, Tantalum or Ceramic capacitor, and a mini-

mum value of 1uF and ESR above 0.06Ω is

recommended. The curve of the stable region in typi-

cal characteristics shows the appropriate output ca-

pacitor ESR for different load current stable operation.

A larger output capacitor can reduce noise and im-

prove load-transient response, stability, and PSRR.

Note that some ceramic dielectrics exhibit large ca-

pacitance and ESR variation with temperature. When

using this capacitor, a minimum 2.2uF or more may

be required to ensure the stability at low temperature

operation. Use a bypass capacitor at BP pin for low

output nvise. Increasing the capacitance will slightly

decrease the output noise, but increase the start-up

time. (See Shutdown Exit Delay and Output Noise

vs.Bypass Capacitor graph in the typical

characteristics)

Load-Transient Considerations

Input-Output (Dropout)Voltage

Reverse Current Pr otection

The APL5301/2 have an internal reverse protection, it

does not need an external schottky diode to connect

the regulator input and output. If the output voltage is

forced above the input voltage by more than 11mV,

the IC will be shutdown and the ground pin current is

below 0.1uA.

Current Limit

The APL5301/2 have a current limit protection. The

ouptut voltage will drop close to zero volt, when load

current reaches the limit, and then the load current

will be limited at 50mA after output voltage is below 0.

7V. When the load current back to the value where

limiting started, the output voltage and current will re-

turn to normal value. When output is shorted to

ground, the APL5301/2 will keep short circuit current

at 150mA .

Rev. A.9 - Apr., 2003

APL5301/2

www.anpec.com.tw11

Thermal protection limits total power dissipation in the

device. When the junction temperature exceeds

TJ=+150J, the thermal sensor generates a logic sig-

nal to turn off the pass transistor and allows IC to

cool. When the IC’s junction temperature is down by

10J, the thermal sensor will turn the pass transistor

on again, resulting in a pulsed output during continu-

ous thermal protection. Thermal protection is designed

to protect the APL5301/2 in the event of fault

conditions. For continuous operation, do not exceed

the absolute maximum junction temperature of

TJ=+150J.

Operating Region and Power Dis-

sipation

The thermal resistance of the case to circuit board,

and the rate of air flow all control the APL5301/2’s

maximum power dissipation. The power dissipation

across the device is PD = IOUT (VIN-VOUT) and the maxi-

mum power dissipation is:

PDMAX = (TJ-TA) / (?JC + ?CA)

where TJ-TA is the temperature difference between the

junction and ambient air, ?JC is the thermal resis-

tance of the package, and?CA is the thermal resis-

tance through the printed circuit board, copper traces,

and other materials to the ambient air.

The GND pin of the APL5301 and APL5302 that the

packages ard SOT-23-5, SOT-89-5 AND SOP-8 pro-

vide an electrical connection to ground and channel-

ing heat away. If power dissipation is large, connect

the GND pin to ground using a large pad or ground

plane, can improve the problem of over heat of IC.

T hermal Protection

Rev. A.9 - Apr., 2003

APL5301/2

www.anpec.com.tw12

Millimeters Inches

Dim Min. Max. Min. Max.

A 1.35 1.75 0.053 0.069

A1 0.10 0.25 0.004 0.010

D 4.80 5.00 0.189 0.197

E 3.80 4.00 0.150 0.157

H 5.80 6.20 0.228 0.244

L 0.40 1.27 0.016 0.050

e1 0.33 0.51 0.013 0.020

e2 1.27BSC 0.50BSC

φ 18

°8°

e1 e2

0.015X45

0.004max.

SOP-8 pin ( Reference JEDEC Registration MS-012)

Packaging Information

Rev. A.9 - Apr., 2003

APL5301/2

www.anpec.com.tw13

SOT-23

Packaging Information

E H

A1 LC

Millimeters Inches

Dim Min. Max. Min. Max.

A 1.00 1.30 0.039 0.051

A1 0.00 0.10 0.000 0.004

B 0.35 0.51 0.014 0.020

C 0.10 0.25 0.004 0.010

D 2.70 3.10 0.106 0.122

E 1.40 1.80 0.055 0.071

e 1.90 BSC 0.075 BSC

H 2.40 3.00 0.094 0.118

L 0.37 0.0015

Rev. A.9 - Apr., 2003

APL5301/2

www.anpec.com.tw14

Packaging Information

SOT-23-5

E1 E

12 3

A2 A

A1 L 2 L

L 1

Millimeters Inches

Dim Min. Max. Min. Max.

A 0.95 1.45 0.037 0.057

A1 0.05 0.15 0.002 0.006

A2 0.90 1.30 0.035 0.051

D2.83.00

0.110 0.118

E2.63.00

0.102 0.118

E1 1.5 1.70 0.059 0.067

L 0.35 0.55 0.014 0.022

L1 0.20 BSC 0.008 BSC

L2 0.5 0.7 0.020 0.028

N5 5

α0°10°0°10°

Rev. A.9 - Apr., 2003

APL5301/2

www.anpec.com.tw15

SOT-89 (Reference EIAJ ED-7500A Reg stration SC-62)

Packaging Information

123

Millimeters Inches

Dim Min. Max. Min. Max.

A 1.40 1.60 0.055 0.063

B 0.40 0.56 0.016 0.022

B1 0.35 0.48 0.014 0.019

C 0.35 0.44 0.014 0.017

D 4.40 4.60 0.173 0.181

D1 1.35 1.83 0.053 0.072

e 1 .50 BS C 0.059 B SC

e1 3.00 BSC 0.118 BSC

E 2.29 2.60 0.090 0.102

H 3.75 4.25 0.148 0.167

L 0.80 1.20 0.031 0.047

α10°10°

Rev. A.9 - Apr., 2003

APL5301/2

www.anpec.com.tw16

Packaging Information

SOT-89-5

Millimeters Inches

Dim Min. Max. Min. Max.

A 4.40 4.60 0.17 0.18

B 4.05 4.25 0.16 0.17

C 1.50 1.70 0.06 0.07

D 1.30 1.50 0.05 0.06

E 2.40 2.60 0.09 0.1

F 0.80 - 0.03 -

G 3.00 R EF 0.12 RE F

H 1.50 R EF 0.06 R EF

I 0.40 0.52 0.01 0.02

J 1.40 1.60 0.05 0.06

K 0.35 0.41 0.01 0.02

L 5 TYP 0.2 TYP

Rev. A.9 - Apr., 2003

APL5301/2

www.anpec.com.tw17

Physical Specifications

Pre-heat temperature

183 C

Peak temperature

Time

temperature

Classification Reflow Profiles

Convection or I R/

Convection VPR

Average ramp-up rate(183°C to Peak ) 3°C/second max. 10 °C /s econd max.

Preheat temperature 125 ± 25°C) 120 seconds max

Temperature m aint ained above 183°C60 – 150 seconds

Time within 5°C of actual peak temperature 10 – 20 sec onds 60 seconds

Peak tem peratur e range 220 +5/-0 °C or 235 +5/-0°C 215-219°C or 235 +5/-0°C

Ramp-down rate 6 °C /second max. 10 °C /second max .

Time 25°C to peak temperatur e 6 minutes max .

Package Reflow Conditions

pkg. thickness ≥

≥≥

≥ 2.5mm

and all bgas pkg. thickness < 2.5mm and

pkg. volume ≥

≥≥

≥ 350 mm³ pkg. thickness < 2.5mm and pkg.

volume < 350mm³

Convection 220 +5/- 0 °C Convect i on 235 +5/-0 °C

VPR 215-219 °C VPR 235 +5/-0 °C

IR/Convection 220 +5/-0 °C IR/Convection 235 +5/-0 °C

Terminal Material Solder-Plated Copper (Solder Material : 90/10 or 63/37 SnPb)

Lead Solderability Meets EIA Specification RSI86-91, ANSI/J-STD-002 Category 3.

Reference JEDEC Standard J-STD-020A APRIL 1999

Reflow Condition (IR/Convection or VPR Reflow)

Rev. A.9 - Apr., 2003

APL5301/2

www.anpec.com.tw18

Re lia b ility te s t p ro gra m

Test item M ethod Description

SOLDERABILITY MIL-STD-883D-2003 245°C , 5 SEC

HOLT MIL-STD-883D-1005.7 1000 H rs Bias @ 125 °C

PCT JESD-22-B, A102 168 Hrs, 100 % RH , 121°C

TST MIL-STD-883D-1011.9 -65°C ~ 150°C , 200 C ycles

ESD M IL-STD-883D-3015.7 VHBM > 2KV, VM M > 200V

L a tc h-Up J E SD 7 8 1 0 ms , Itr > 100m A

Carrier Tape

Po P

Rev. A.9 - Apr., 2003

APL5301/2

www.anpec.com.tw19

lication A B C J T1 T2 W P E

330 ± 162 +1.512.75+

0.15 2 ± 0.5 12.4 ± 0.2 2 ± 0.2 12± 0. 3 8± 0.1 1.75±0.1

F D D1 Po P1 Ao Bo Ko t

SOP- 8

5.5± 1 1.55 +0.1 1.55+ 0.25 4.0 ± 0 .1 2.0 ± 0.1 6 .4 ± 0 .1 5 .2 ± 0. 1 2 .1 ± 0.1 0.3±0.013

lication A B C J T1 T2 W P E

178 ±170

± 213.5 ± 0.15 3 ± 0.15 14 ± 21.3 ± 0.3 12 + 0.3

12 - 0.1 8 ± 0.1 1 .7 5± 0.1

F D D1 Po P1 Ao Bo Ko t

SOT-89

5.5 ± 0.05 1.5± 0.1 1 .5± 0 .1 4 .0 ± 0.1 2 .0 ± 0.1 4 .8 ± 0.1 4.5± 0.1 1.80± 0.1 0.3±0.013

lication A B C J T1 T2 W P E

178±172

± 1.0 13.0 + 0.2 2.5 ± 0.15 8.4 ± 21.5

± 0.3 8.0+ 0.3

- 0 .3 4 ± 0.1 1 .7 5 ± 0.1

F D D1 Po P1 Ao Bo Ko t

SOT-23-5

3.5 ± 0.05 1.5 +0.1 1.5 +0.1 4.0 ± 0 .1 2.0 ± 0.1 3.15 ± 0.1 3.2± 0.1 1.4± 0 .1 0 .2 ±0.03

Cover Tape Dimensions

Anpec Electronics Corp.

Head Office :

5F, No. 2 Li-Hsin Road, SBIP,

Hsin-Chu, Taiwan, R.O.C.

Tel : 886-3-5642000

Fax : 886-3-5642050

Taipei Branch :

7F, No. 137, Lane 235, Pac Chiao Rd.,

Hsin T ien City, Taipei Hsien, Taiwan, R. O. C.

Tel : 886-2-89191368

Fax : 886-2-89191369

Customer Service

Reel Dimensions

Application Carrier Width Cover Ta pe Width Devices Per Reel

SOP- 8 12 9.3 2500

SOT- 23 8 5.3 3000

SOT- 89 12 9.3 1000