Catalog 82047 Power Cord Receptacles Revised 6-00 Product Facts Designed to international standard CEE-22 Recognized under the Component Recognition Program of Underwriters Laboratories Inc., File No. E28476 Certified by Canadian Standards Association, File No. LK7189 VDE approved, License No. 70442 and 70443 Mate with standard international plugs Machine applied, crimp, snap-in contacts Same contact design for ground and power -- one inventory item Rear of housing is egg-crated for maximum protection -- no post termination sleeving required Photo 42670 Technical Document Instruction Sheets - 408-7711 - 408-7686 - Power Cord Receptacle Housing PN 206637-1 - Extraction Tool PN 91106-1 Application Specification - 114-10044 - Power Cord Receptacle Housing PN 206637-1 AMP Power Cord Receptacles are designed to electrical specification CEE-22, the international standard used by most European nations. AMP Power Cord receptacles are available in a 3position and a 5-position male configuration with a polarized, thermoplastic housing suitable for rack or panel mounting. The crimp, snap-in contacts are tin plated and have a rectangular cross section. The ground contact extends .118 [3] farther forward than the power contacts when installed in the housing, to provide for proper grounding prior to power engagement. them for 250 volts, 10 amperes. They are recognized by Underwriters Laboratories Inc., under the Component Recognition Program, at 250 volts, 15 amperes when wired with appropriate 16 AWG [1.25-1.4mm2] wire per table 400-5 of the national electrical code. CSA certifies the receptacles for 250 volts, 15 amps. Because of configuration controls, CEE rates them for 250 volts, 10 amperes. VDE certifies Contacts are available in strip form for high-speed, automatic machine application at lowest cost, and loose-piece contacts are available for hand tool application for repair or maintenance. In addition to economies of application by automatic machine, the egg crate design at the rear of the housing cavities eliminates the need for costly post-termination insulation sleeving. (c) 1976, 1983, 1989 and 2000 Tyco Electronics Corporation All Rights Reserved AMP, AMP-O-LECTRIC, Tyco -- Trademarks Technical Support Center/AMP FAX Service 1-800-522-6752 717-986-7777 Dimensions are in inches over [millimeters] www.amp.com Specifications subject to change. 1 Catalog 82047 Power Cord Receptacles Revised 6-00 Materials and Finish Housing - Thermoplastic, 94V-0 rated; 90 C temperature rating; black Contact - Brass Contact Finish - Tin Receptacle (Ref.) Inside Edges of Rack 3-Position Housing Part Number 206637-1 .130 .008 Dia. [3.30 .003] 2 Holes .276 [7.00] 1.564 .006 [39.98 0.15] .276 [7.00] .760 [19.30] .657 [16.69] 1.969 .020 [50.01 0.51] 1.063 [27.00] .954 .008 [24.23] 1.181 0.20 Dia. [30.00 ] .659 [16.74] .200 .010 [5.08 0.25] .197 [5.00] .880 [22.35] 5-Position Housing Part Number 211395-1 .126 Dia. [3.20] .130 .003 Dia. [3.30 0.08] 2 Holes .276 .006 [7.01 0.15] .157 .006 [3.99 0.15] 1.102 [27.99] 1.812 .006 [46.02 0.15] 1.575 [40.00] Rack Mounting (for 3-Position Housing) .803 [20.04] Cutout .402 [10.21] .185 R. [4.70] 1.166 R [4.22] 4 Plc. 1.455 .010 [36.96 0.25] .220 R [5.59 R] 4 Plc. 1.351 [34.32] 2.260 .010 [57.40 0.25] 1.481 .008 [37.62 0.20] .276 .006 [7.01 0.15] .396 .006 .200 .010 [10.060.15] [5.08 0.25] .276 [7.01 0.15] .006 .660 [16.76] .880 [22.35] .752 [19.10] 1.455 .010 [36.96 0.25] Pin Contacts .157 .004 [3.99 0.10] .126 Dia. [3.20] .059 .011 [1.50 0.28] .085 [2.16 0.25] .010 1.102 [27.99] 1.575 [40.00] .023 Max. [0.58] .078 .002 [1.98 0.05] Panel Mounting (for 3-Position Housing) .147 Min. [3.73] Wire Insulation Range .080/.135 Dia. [2.03 - 3.43] 1.823 [46.30] .220 R 4 Plc. AWG .752 [19.10] 1.524 [38.71] .126 Dia. [3.20] Rack Mounting (for 5-Position Housing) 1.524 [38.71] .126 Dia. [3.20] .185 R 4 Plc. .402 [10.21] 1.823 [46.30] Panel Mounting (for 5-Position Housing) 82047-5M-DAS-6-00 .803 [20.04] Wire Size Range mm2 20.16 0.5-1.4 18-14 0.8-2.0 Ins. Dia. Range .080-.135 2.08-3.43 .080-.135 Pin Contact Part Number Strip Form Loose Piece Applicator Part Number 206638-2 206638-3 466136-2 208914-2 -- 567188-2 Extraction Tool Part Number 91106-1 AMP-O-LECTRIC Terminating Machine A complete line of application tooling is available to meet a wide range of production needs -- from precision hand tools and bench-mounted semiautomatic machines to fully automatic lead making machines. Consult AMP (for 3-Position Housing) for the exact machines for specific applications. Technical Support Center/AMP FAX Service 1-800-522-6752 717-986-7777 Photo 81169 Dimensions are in inches over [millimeters] www.amp.com Specifications subject to change. 2