ST24/25C04, ST24C04R ST24/25W04 SERIAL 4K (512 x 8) EEPROM 1 MILLION ERASE/WRITE CYCLES with 40 YEARS DATA RETENTION SINGLE SUPPLY VOLTAGE: - 3V to 5.5V for ST24x04 versions - 2.5V to 5.5V for ST25x04 versions - 1.8V to 5.5V for ST24C04R version only HARDWARE WRITE CONTROL VERSIONS: ST24W04 and ST25W04 PROGRAMMABLE WRITE PROTECTION TWO WIRE SERIAL INTERFACE, FULLY I2C BUS COMPATIBLE BYTE and MULTIBYTE WRITE (up to 4 BYTES) PAGE WRITE (up to 8 BYTES) BYTE, RANDOM and SEQUENTIAL READ MODES SELF TIMED PROGRAMMING CYCLE AUTOMATIC ADDRESS INCREMENTING ENHANCED ESD/LATCH UP PERFORMANCES 8 8 1 1 PSDIP8 (B) 0.25mm Frame SO8 (M) 150mil Width Figure 1. Logic Diagram VCC DESCRIPTION This specification covers a range of 4K bits I2C bus EEPROM prod ucts, t he ST 24 /25C04, the ST24C04R and the ST24/25W04. In the text, products are referred to as ST24/25x04, where "x" is: "C" for Standard version and "W" for hardware Write Control version. 2 E1-E2 PRE SCL Table 1. Signal Names PRE Write Protect Enable E1-E2 Chip Enable Inputs SDA Serial Data Address Input/Output SCL Serial Clock MODE Multibyte/Page Write Mode (C version) WC Write Control (W version) VCC Supply Voltage VSS Ground July 1996 SDA ST24x04 ST25x04 St24C04R MODE/WC* VSS AI00851D Note: WC signal is only available for ST24/25W04 products. 1/16 ST24/25C04, ST24C04R, ST24/25W04 Figure 2A. DIP Pin Connections Figure 2B. SO Pin Connections ST24x04 ST25x04 ST24C04R PRE E1 E2 VSS 1 2 3 4 8 7 6 5 ST24x04 ST25x04 ST24C04R PRE E1 E2 VSS VCC MODE/WC SCL SDA AI00852D 1 2 3 4 8 7 6 5 VCC MODE/WC SCL SDA AI01107D Table 2. Absolute Maximum Ratings (1) Symbol Parameter Value Unit Ambient Operating Temperature -40 to 125 C TSTG Storage Temperature -65 to 150 C TLEAD Lead Temperature, Soldering TA VIO Input or Output Voltages VCC Supply Voltage VESD (SO8 package) (PSDIP8 package) Electrostatic Discharge Voltage (Human Body model) Electrostatic Discharge Voltage (Machine model) (3) (2) 40 sec 10 sec 215 260 C -0.6 to 6.5 V -0.3 to 6.5 V 4000 V 500 V Notes: 1. Except for the rating "Operating Temperature Range", stresses above those listed in the Table "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions above those indicated in the Operating sections of this specification is not implied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. Refer also to the SGS-THOMSON SURE Program and other relevant quality documents. 2. MIL-STD-883C, 3015.7 (100pF, 1500 ). 3. EIAJ IC-121 (Condition C) (200pF, 0 ). DESCRIPTION (cont'd) The ST24/25x04 are 4K bit electrically erasable programmable memories (EEPROM), organized as 2 blocks of 256 x 8 bits. They are manufactured in SGS-THOMSON's Hi-Endurance Advanced CMOS technology which guarantees an endurance of one million erase/write cycles with a data retention of 40 years. The memories operate with a power supply value as low as 1.8V for the ST24C04R only. Both Plastic Dual-in-Line and Plastic Small Outline packages are available. The memories are compatible with the I2C standard, two wire serial interface which uses a bi-direc2/16 tional data bus and serial clock. The memories carry a built-in 4 bit, unique device identification code (1010) corresponding to the I2C bus definition. This is used together with 2 chip enable inputs (E2, E1) so that up to 4 x 4K devices may be attached to the I2C bus and selected individually. The memories behave as a slave device in the I2C protocol with all memory operations synchronized by the serial clock. Read and write operations are initiated by a START condition generated by the bus master. The START condition is followed by a stream of 7 bits (identification code 1010), plus one read/write bit and terminated by an acknowledge bit. ST24/25C04, ST24C04R, ST24/25W04 Table 3. Device Select Code Device Code Chip Enable Block Select RW Bit b7 b6 b5 b4 b3 b2 b1 b0 Device Select 1 0 1 0 E2 E1 A8 RW Note: The MSB b7 is sent first. Table 4. Operating Modes (1) Mode RW bit MODE Bytes Current Address Read '1' X 1 X 1 Random Address Read '0' '1' Initial Sequence START, Device Select, RW = '1' START, Device Select, RW = '0', Address, reSTART, Device Select, RW = '1' Sequential Read '1' X 1 to 512 Byte Write '0' X 1 START, Device Select, RW = '0' '0' VIH 4 START, Device Select, RW = '0' '0' VIL 8 START, Device Select, RW = '0' Multibyte Write Page Write (2) Similar to Current or Random Mode Notes: 1. X = VIH or VIL 2. Multibyte Write not available in ST24/25W04 versions. When writing data to the memory it responds to the 8 bits received by asserting an acknowledge bit during the 9th bit time. When data is read by the bus master, it acknowledges the receipt of the data bytes in the same way. Data transfers are terminated with a STOP condition. Power On Reset: VCC lock out write protect. In order to prevent data corruption and inadvertent write operations during power up, a Power On Reset (POR) circuit is implemented. Until the VCC voltage has reached the POR threshold value, the internal reset is active, all operations are disabled and the device will not respond to any command. In the same way, when VCC drops down from the operating voltage to below the POR threshold value, all operations are disabled and the device will not respond to any command. A stable VCC must be applied before applying any logic signal. SIGNAL DESCRIPTIONS Serial Clock (SCL). The SCL input pin is used to synchronize all data in and out of the memory. A resistor can be connected from the SCL line to VCC to act as a pull up (see Figure 3). Serial Data (SDA). The SDA pin is bi-directional and is used to transfer data in or out of the memory. It is an open drain output that may be wire-OR'ed with other open drain or open collector signals on the bus. Aresistor must be connectedfrom the SDA bus line to VCC to act as pull up (see Figure 3). Chip Enable (E1 - E2). These chip enable inputs are used to set the 2 least significant bits (b2, b3) of the 7 bit device select code. These inputs may be driven dynamically or tied to VCC or VSS to establish the device select code. Protect Enable (PRE). The PRE input pin, in addition to the status of the Block Address Pointer bit (b2, location 1FFh as in Figure 7), sets the PRE write protection active. Mode (MODE). The MODE input is available on pin 7 (see also WC feature) and may be driven dynamically. It must be at VIL or VIH for the Byte Write mode, VIH for Multibyte Write mode or VIL for Page Write mode. When unconnected, the MODE input is internally read as VIH (Multibyte Write mode). Write Control (WC). An hardware Write Control feature (WC) is offered only for ST24W04 and ST25W04 versions on pin 7. This feature is usefull to protect the contents of the memory from any erroneous erase/write cycle. The Write Control signal is used to enable (WC = VIH) or disable (WC = VIL) the internal write protection. When unconnected, the WC input is internally read as VIL and the memory area is not write protected. 3/16 ST24/25C04, ST24C04R, ST24/25W04 SIGNAL DESCRIPTIONS (cont'd) The devices with this Write Control feature no longer support the Multibyte Write mode of operation, however all other write modes are fully supported. Refer to the AN404 Application Note for more detailed information about Write Control feature. DEVICE OPERATION I2C Bus Background The ST24/25x04 support the I2C protocol. This protocol defines any device that sends data onto the bus as a transmitter and any device that reads the data as a receiver. The device that controls the data transfer is known as the master and the other as the slave. The master will always initiate a data transfer and will provide the serial clock for synchronisation. The ST24/25x04 are always slave devices in all communications. Start Condition. START is identified by a high to low transition of the SDA line while the clock SCL is stable in the high state. A START condition must precede any command for data transfer. Except during a programming cycle, the ST24/25x04 continuously monitor the SDA and SCL signals for a START condition and will not respond unless one is given. Stop Condition. STOP is identified by a low to high transition of the SDA line while the clock SCL is stable in the high state. A STOP condition terminates communication between the ST24/25x04 and the bus master. A STOP condition at the end of a Read command, after and only after a No Acknowledge, forces the standby state. A STOP condition at the end of a Write command triggers the internal EEPROM write cycle. Acknowledge Bit (ACK). An acknowledge signal is used to indicate a successfull data transfer. The bus transmitter, either master or slave, will release the SDA bus after sending 8 bits of data. During the 9th clock pulse period the receiver pulls the SDA bus low to acknowledge the receipt of the 8 bits of data. Data Input. During data input the ST24/25x04 sample the SDA bus signal on the rising edge of the clock SCL. Note that for correct device operation the SDA signal must be stable during the clock low to high transition and the data must change ONLY when the SCL line is low. Memory Addressing. To start communication between the bus master and the slave ST24/25x04, the master must initiate a START condition. Following this, the master sends onto the SDA bus line 8 bits (MSB first) corresponding to the device select code (7 bits) and a READ or WRITE bit. Figure 3. Maximum RL Value versus Bus Capacitance (C BUS) for an I2C Bus 20 VCC 16 RL max (k) RL 12 RL SDA MASTER CBUS SCL 8 CBUS 4 VCC = 5V 0 100 200 CBUS (pF) 4/16 300 400 AI01100 ST24/25C04, ST24C04R, ST24/25W04 Table 5. Input Parameters (1) (TA = 25 C, f = 100 kHz ) Symbol Parameter Test Condition Min Max Unit CIN Input Capacitance (SDA) 8 pF CIN Input Capacitance (other pins) 6 pF 20 k ZWCL WC Input Impedance (ST24/25W04) VIN 0.3 VCC 5 ZWCH WC Input Impedance (ST24/25W04) VIN 0.7 VCC 500 tLP Low-pass filter input time constant (SDA and SCL) k 100 ns Note: 1. Sampled only, not 100% tested. Table 6. DC Characteristics (TA = 0 to 70C, -20 to 85C or -40 to 85C; VCC = 3V to 5.5V, 2.5V to 5.5V or 1.8V to 5.5V) Symbol Parameter Test Condition ILI Input Leakage Current ILO Output Leakage Current ICC ICC1 ICC2 ICC3 ICC4 Max Unit 0V VIN VCC 2 A 0V VOUT VCC SDA in Hi-Z 2 A Supply Current (ST24 series) VCC = 5V, fC = 100kHz (Rise/Fall time < 10ns) 2 mA Supply Current (ST25 series) VCC = 2.5V, fC = 100kHz 1 mA VIN = VSS or VCC, VCC = 5V 100 A VIN = VSS or VCC, VCC = 5V, fC = 100kHz 300 A VIN = VSS or VCC, VCC = 2.5V 5 A VIN = VSS or VCC, VCC = 2.5V, fC = 100kHz 50 A VIN = VSS or VCC, VCC = 3.6V 20 A VIN = VSS or VCC, VCC = 3.6V, fC = 100kHz 60 A VIN = VSS or VCC, VCC = 1.8V 10 A VIN = VSS or VCC, VCC = 1.8V, fC = 100kHz 20 A Supply Current (Standby) (ST24 series) Supply Current (Standby) (ST25 series) Supply Current (Standby) (ST24C04R) Supply Current (Standby) (ST24C04R) Min VIL Input Low Voltage (SCL, SDA) -0.3 0.3 VCC V VIH Input High Voltage (SCL, SDA) 0.7 VCC VCC + 1 V VIL Input Low Voltage (E1-E2, PRE, MODE, WC) -0.3 0.5 V VIH Input High Voltage (E1-E2, PRE, MODE, WC) VCC - 0.5 VCC + 1 V VOL Output Low Voltage (ST24 series) IOL = 3mA, VCC = 5V 0.4 V Output Low Voltage (ST25 series) IOL = 2.1mA, VCC = 2.5V 0.4 V IOL = 1mA, VCC = 1.8V 0.3 V Output Low Voltage (ST24C04R) 5/16 ST24/25C04, ST24C04R, ST24/25W04 Table 7. AC Characteristics (TA = 0 to 70C, -20 to 85C or -40 to 85C; VCC = 3V to 5.5V, 2.5V to 5.5V or 1.8V to 5.5V) Symbol Alt tCH1CH2 tR tCL1CL2 Max Unit Clock Rise Time 1 s tF Clock Fall Time 300 ns tDH1DH2 tR Input Rise Time 1 s tDL1DL1 tF Input Fall Time 300 ns tCHDX (1) tSU:STA Parameter Min 4.7 s Clock Pulse Width High 4 s Clock High to Input Transition tCHCL tHIGH tDLCL tHD:STA Input Low to Clock Low (START) 4 s tCLDX tHD:DAT Clock Low to Input Transition 0 s tCLCH tLOW Clock Pulse Width Low 4.7 s tDXCX tSU:DAT Input Transition to Clock Transition 250 ns tCHDH tSU:STO Clock High to Input High (STOP) 4.7 s tDHDL tBUF Input High to Input Low (Bus Free) 4.7 s tAA Clock Low to Next Data Out Valid 0.3 tCLQX tDH Data Out Hold Time 300 fC fSCL Clock Frequency 100 kHz tWR Write Time 10 ms tCLQV tW (2) (3) 3.5 s ns Notes: 1. For a reSTART condition, or following a write cycle. 2. The minimum value delays the falling/rising edge of SDA away from SCL = 1 in order to avoid unwanted START and/or STOP conditions. 3. In the Multibyte Write mode only, if accessed bytes are on two consecutive 8 bytes rows (6 address MSB are not constant) the maximum programming time is doubled to 20ms. AC MEASUREMENT CONDITIONS DEVICE OPERATION (cont'd) Input Rise and Fall Times 50ns Input Pulse Voltages 0.2VCC to 0.8VCC Input and Output Timing Ref. Voltages 0.3VCC to 0.7VCC Figure 4. AC Testing Input Output Waveforms 0.8VCC 0.2VCC 0.7VCC 0.3VCC AI00825 6/16 The 4 most significant bits of the device select code are the device type identifier, corresponding to the I2C bus definition. For these memories the 4 bits are fixed as 1010b. The following 2 bits identify the specific memory on the bus. They are matched to the chip enable signals E2, E1. Thus up to 4 x 4K memories can be connected on the same bus giving a memory capacity total of 16K bits. After a START condition any memory on the bus will identify the device code and compare the following 2 bits to its chip enable inputs E2, E1. The 7th bit sent is the block number (one block = 256 bytes). The 8th bit sent is the read or write bit (RW), this bit is set to '1' for read and '0' for write operations. If a match is found, the corresponding memory will acknowledge the identification on the SDA bus during the 9th bit time. ST24/25C04, ST24C04R, ST24/25W04 Figure 5. AC Waveforms tCLCH tCHCL SCL tDLCL tDXCX tCHDH SDA IN tCHDX START CONDITION tCLDX tDHDL SDA INPUT SDA CHANGE STOP & BUS FREE SCL tCLQV tCLQX DATA VALID SDA OUT DATA OUTPUT tDHDL SCL tW SDA IN tCHDH STOP CONDITION tCHDX WRITE CYCLE START CONDITION AI00795 Write Operations The Multibyte Write mode (only available on the ST24/25C04 and ST24C04R versions) is selected when the MODE pin is at VIH and the Page Write mode when MODE pin is at VIL. The MODE pin may be driven dynamically with CMOS input levels. Following a START condition the master sends a device select code with the RW bit reset to '0'. The memory acknowledges this and waits for a byte address. The byte address of 8 bits provides access to one block of 256 bytes of the memory. After receipt of the byte address the device again responds with an acknowledge. For the ST24/25W04 versions, any write command with WC = 1 will not modify the memory content. Byte Write. In the Byte Write mode the master sends one data byte, which is acknowledged by the memory. The master then terminates the transfer by generating a STOP condition. The Write mode is independantof the state of the MODE pin which could be left floating if only this mode was to be used. However it is not a recommended operating mode, as this pin has to be connected to either VIH or VIL, to minimize the stand-by current. 7/16 ST24/25C04, ST24C04R, ST24/25W04 Figure 6. I2C Bus Protocol SCL SDA START CONDITION SCL 1 SDA MSB SDA INPUT 2 SDA CHANGE STOP CONDITION 3 7 8 9 ACK START CONDITION SCL 1 SDA MSB 2 3 7 8 9 ACK STOP CONDITION AI00792 Multibyte Write. For the Multibyte Write mode, the MODE pin must be at VIH. The Multibyte Write mode can be started from any address in the memory. The master sends from one up to 4 bytes of data, which are each acknowledgedby the memory. The transfer is terminated by the master generating a STOP condition. The duration of the write cycle is t W = 10ms maximum except when bytes are accessed on 2 rows (that is have different values for the 6 most significant address bits A7A2), the programming time is then doubled to a maximum of 20ms. Writing more than 4 bytes in the 8/16 Multibyte Write mode may modify data bytes in an adjacent row (one row is 8 bytes long). However, the Multibyte Write can properly write up to 8 consecutive bytes as soon as the first address of these 8 bytes is the first address of the row, the 7 following bytes being written in the 7 following bytes of this same row. Page Write. For the Page Write mode, the MODE pin must be at VIL. The Page Write mode allows up to 8 bytes to be written in a single write cycle, provided that they are all located in the same 'row' in the memory: that is the 5 most significant mem- ST24/25C04, ST24C04R, ST24/25W04 ory address bits (A7-A3) are the same inside one block. The master sends from one up to 8 bytes of data, which are each acknowledged by the memory. After each byte is transfered, the internal byte address counter (3 least significant bits only) is incremented. The transfer is terminated by the master generating a STOP condition. Care must be taken to avoid address counter 'roll-over' which could result in data being overwritten. Note that, for any write mode, the generationby the master of the STOP condition starts the internal memory program cycle. All inputs are disabled until the completion of this cycle and the memory will not respond to any request. Minimizing System Delays by Polling On ACK. During the internal write cycle, the memory disconnects itself from the bus in order to copy the data from the internal latches to the memory cells. The maximum value of the write time (tW) is given in the AC Characteristics table, since the typical time is shorter, the time seen by the system may be reduced by an ACK polling sequence issued by the master. Figure 7. Memory Protection Protect Location 8 byte boundary address b7 Protect Flag Enable = 0 Disable = 1 b3 b2 1FFh X X Block 1 100h Block 0 AI00855B Figure 8. Write Cycle Polling using ACK WRITE Cycle in Progress START Condition DEVICE SELECT with RW = 0 NO First byte of instruction with RW = 0 already decoded by ST24xxx ACK Returned YES NO Next Operation is Addressing the Memory YES Send Byte Address ReSTART STOP Proceed WRITE Operation Proceed Random Address READ Operation AI01099B 9/16 ST24/25C04, ST24C04R, ST24/25W04 Figure 9. Write Modes Sequence (ST24/25C04 and ST24C04R) ACK BYTE ADDR DATA IN R/W ACK MULTIBYTE AND PAGE WRITE ACK STOP DEV SEL START BYTE WRITE ACK START DEV SEL ACK BYTE ADDR ACK DATA IN 1 DATA IN 2 R/W ACK ACK STOP DATA IN N AI00793 DEVICE OPERATION (cont'd) The sequence is as follows: - Initial condition:a Write is in progress (see Figure 8). - Step 1: the Master issues a START condition followed by a Device Select byte (1st byte of the new instruction). - Step 2: if the memory is busy with the internal write cycle, no ACK will be returned and the master goes back to Step 1. If the memory has terminated the internal write cycle, it will respond with an ACK, indicating that the memory is ready to receive the second part of the next instruction (the first byte of this instruction was already sent during Step 1). Write Protection. Data in the upper block of 256 bytes of the memory may be write protected. The memory is write protected between a boundary address and the top of memory (address 1FFh) when the PRE input pin is taken high and when the Protect Flag (bit b2 in location 1FFh) is set to '0'. The boundary address is user defined by writing it in the Block Address Pointer. The Block Address Pointer is an 8 bit EEPROM register located at the address 1FFh. It is composed by 5 MSBs Address Pointer, which defines the bottom boundary address, and 3 LSBs which must be programmed at 10/16 '0'. This Address Pointer can therefore address a boundary in steps of 8 bytes. The sequence to use the Write Protected feature is: - write the data to be protected into the top of the memory, up to, but not including, location 1FFh; - set the protection by writing the correct bottom boundary address in the Address Pointer (5 MSBs of location 1FFh) with bit b2 (Protect flag) set to '0'. Note that for a correct fonctionality of the memory, all the 3 LSBs of the Block Address Pointer must also be programmed at '0'. The area will now be protected when the PRE input pin is taken High. While the PRE input pin is read at '0' by the memory, the location 1FFh can be used as a normal EEPROM byte. Caution: Special attention must be used when using the protect mode together with the Multibyte Write mode (MODE input pin High). If the Multibyte Write starts at the location right below the first byte of the Write Protected area, then the instruction will write over the first 3 bytes of the Write Protected area. The area protected is therefore smaller than the content defined in the location 1FFh, by 3 bytes. This does not apply to the Page Write mode as the address counter 'roll-over' and thus cannot go above the 8 bytes lower boundary of the protected area. ST24/25C04, ST24C04R, ST24/25W04 Figure 10. Write Modes Sequence with Write Control = 1 (ST24/25W04) WC ACK BYTE ADDR ACK DATA IN STOP DEV SEL START BYTE WRITE ACK R/W WC ACK DEV SEL START PAGE WRITE ACK BYTE ADDR ACK DATA IN 1 DATA IN 2 R/W WC (cont'd) ACK DATA IN N STOP PAGE WRITE (cont'd) ACK AI01101B Read Operations Read operationsare independentof the state of the MODE pin. On delivery, the memory content is set at all "1's" (or FFh). Current Address Read. The memory has an internal byte address counter. Each time a byte is read, this counter is incremented. For the Current Address Read mode, following a START condition, the master sends a memory address with the RW bit set to '1'. The memory acknowledges this and outputs the byte addressed by the internal byte address counter. This counter is then incremented. The master does NOT acknowledge the byte output, but terminates the transfer with a STOP condition. Random Address Read. A dummy write is performed to load the address into the address counter, see Figure 11. This is followed by another START condition from the master and the byte address is repeated with the RW bit set to '1'. The memory acknowledges this and outputs the byte addressed. The master have to NOT acknowledge the byte output, but terminates the transfer with a STOP condition. Sequential Read. This mode can be initiated with either a Current Address Read or a Random Address Read. However, in this case the master DOES acknowledge the data byte output and the memory continues to output the next byte in sequence. To terminate the stream of bytes, the master must NOT acknowledge the last byte out- 11/16 ST24/25C04, ST24C04R, ST24/25W04 counter will 'roll- over' and the memory will continue to output data. Acknowledge in Read Mode. In all read modes the ST24/25x04wait for anacknowledge during the 9th bit time. If the master does not pull the SDA line low during this time, the ST24/25x04terminate the data transfer and switches to a standby state. DEVICE OPERATION (cont'd) put, but MUST generate a STOP condition. The output data is from consecutive byte addresses, with the internal byte address counter automatically incremented after each byte output. After a count of the last memory address, the address Figure 11. Read Modes Sequence ACK DATA OUT STOP START DEV SEL NO ACK R/W ACK START DEV SEL * ACK BYTE ADDR R/W ACK START DEV SEL DATA OUT R/W ACK ACK DATA OUT 1 NO ACK DATA OUT N R/W ACK START DEV SEL * ACK BYTE ADDR R/W ACK ACK DEV SEL * START SEQUENTIAL RANDOM READ NO ACK STOP SEQUENTIAL CURRENT READ ACK DEV SEL * START RANDOM ADDRESS READ STOP CURRENT ADDRESS READ ACK DATA OUT 1 R/W NO ACK STOP DATA OUT N AI00794C Note: * The 7 Most Significant bits of DEV SEL bytes of a Random Read (1st byte and 3rd byte) must be identical. 12/16 ST24/25C04, ST24C04R, ST24/25W04 ORDERING INFORMATION SCHEME Example: ST24C04 1 TR Range Operating Voltage ST24C04 3V to 5.5V Standard ST24W04 3V to 5.5V Hardware Write Control ST25C04 2.5V to 5.5V Standard ST25W04 2.5V to 5.5V Hardware Write Control ST24C04R 1.8V to 5.5V Standard Package Notes: M B PSDIP8 0.25mm Frame M SO8 150mil Width Option Temperature Range 1 0 to 70 C 5* -20 to 85 C 6 -40 to 85 C 3* -40 to 125 C TR Tape & Reel Packing 3 * Temperature range on special request only. 5 * Temperature range for ST24C04R only. Parts are shipped with the memory content set at all "1's" (FFh). For a list of available options (Operating Voltage, Range, Package, etc...) refer to the current Memory Shortform catalogue. For further information on any aspect of this device, please contact the SGS-THOMSON Sales Office nearest to you. 13/16 ST24/25C04, ST24C04R, ST24/25W04 PSDIP8 - 8 pin Plastic Skinny DIP, 0.25mm lead frame mm Symb Typ inches Min Max A 3.90 A1 Min Max 5.90 0.154 0.232 0.49 - 0.019 - A2 3.30 5.30 0.130 0.209 B 0.36 0.56 0.014 0.022 B1 1.15 1.65 0.045 0.065 C 0.20 0.36 0.008 0.014 D 9.20 9.90 0.362 0.390 - - - - 6.00 6.70 0.236 0.264 - - - - 7.80 - 0.307 - E 7.62 E1 e1 2.54 eA eB Typ 0.300 0.100 10.00 L 3.00 N 8 0.394 3.80 0.118 8 PSDIP8 A2 A1 B A L e1 eA eB B1 D C N E1 E 1 PSDIP-a Drawing is not to scale 14/16 0.150 ST24/25C04, ST24C04R, ST24/25W04 SO8 - 8 lead Plastic Small Outline, 150 mils body width mm Symb Typ inches Min Max A 1.35 A1 Min Max 1.75 0.053 0.069 0.10 0.25 0.004 0.010 B 0.33 0.51 0.013 0.020 C 0.19 0.25 0.007 0.010 D 4.80 5.00 0.189 0.197 E 3.80 4.00 0.150 0.157 - - - - H 5.80 6.20 0.228 0.244 h 0.25 0.50 0.010 0.020 L 0.40 0.90 0.016 0.035 0 8 0 8 N 8 e 1.27 Typ 0.050 8 CP 0.10 0.004 SO8 h x 45 A C B CP e D N E H 1 A1 L SO-a Drawing is not to scale 15/16 ST24/25C04, ST24C04R, ST24/25W04 Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. SGS-THOMSON Microelectronics products are not authorized for use as critical components in life support devices or systems withoutexpress written approval of SGS-THOMSON Microelectronics. 1996 SGS-THOMSON Microelectronics - All Rights Reserved Purchase of I2C Components by SGS-THOMSON Microelectronics, conveys a license under the Philips I2C Patent. Rights to use these components in an I2C system, is granted provided that the system conforms to the I2C Standard Specifications as defined by Philips. SGS-THOMSON Microelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco - The Netherlands Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A. 16/16