74LV4053 Triple single-pole double-throw analog switch Rev. 04 -- 10 August 2009 Product data sheet 1. General description The 74LV4053 is a triple single-pole double-throw (SPDT) analog switch, suitable for use as an analog or digital multiplexer/demultiplexer. It is a low-voltage Si-gate CMOS device and is pin and function compatible with the 74HC4053 and 74HCT4053. Each switch has a digital select input (Sn), two independent inputs/outputs (nY0 and nY1) and a common input/output (nZ). All three switches share an enable input (E). A HIGH on E causes all switches into the high-impedance OFF-state, independent of Sn. VCC and GND are the supply voltage connections for the digital control inputs (Sn and E). The VCC to GND range is 1 V to 6 V. The analog inputs/outputs (nY0, nY1 and nZ) can swing between VCC as a positive limit and VEE as a negative limit. VCC - VEE may not exceed 6 V. For operation as a digital multiplexer/demultiplexer, VEE is connected to GND (typically ground). VEE and VSS are the supply voltage connections for the switches. 2. Features n Optimized for low-voltage applications: 1.0 V to 3.6 V n Accepts TTL input levels between VCC = 2.7 V and VCC = 3.6 V n Low ON resistance: u 180 (typical) at VCC - VEE = 2.0 V u 100 (typical) at VCC - VEE = 3.0 V u 75 (typical) at VCC - VEE = 4.5 V n Logic level translation: u To enable 3 V logic to communicate with 3 V analog signals n Typical `break before make' built in n ESD protection: u HBM JESD22-A114-C exceeds 2000 V u MM JESD22-A115-A exceeds 200 V n Multiple package options n Specified from -40 C to +85 C and from -40 C to +125 C 74LV4053 NXP Semiconductors Triple single-pole double-throw analog switch 3. Ordering information Table 1. Ordering information Type number Package Temperature range Name Description Version 74LV4053N -40 C to +125 C DIP16 plastic dual in-line package; 16 leads (300 mil) SOT38-4 74LV4053D -40 C to +125 C SO16 plastic small outline package; 16 leads; body width 3.9 mm SOT109-1 74LV4053DB -40 C to +125 C SSOP16 plastic shrink small outline package; 16 leads; body width 5.3 mm SOT338-1 74LV4053PW -40 C to +125 C TSSOP16 plastic thin shrink small outline package; 16 leads; body width 4.4 mm SOT403-1 74LV4053BQ -40 C to +125 C DHVQFN16 plastic dual-in line compatible thermal enhanced very SOT763-1 thin quad flat package; no leads; 16 terminals; body 2.5 x 3.5 x 0.85 mm 4. Functional diagram E 6 VCC 16 13 1Y1 S1 11 LOGIC LEVEL CONVERSION DECODER 12 1Y0 14 1Z 1 2Y1 S2 10 LOGIC LEVEL CONVERSION 2 2Y0 15 2Z 3 3Y1 S3 9 LOGIC LEVEL CONVERSION 5 3Y0 4 3Z 8 GND Fig 1. 7 VEE 001aak341 Functional diagram 74LV4053_4 Product data sheet (c) NXP B.V. 2009. All rights reserved. Rev. 04 -- 10 August 2009 2 of 26 74LV4053 NXP Semiconductors Triple single-pole double-throw analog switch 6 11 S1 1Y0 12 10 S2 1Y1 13 11 9 S3 1Z EN # 14 14 2Y0 2 2Y1 1 10 15 15 2Z 3Y0 5 3Y1 3 3Z 4 9 MUX/DMUX 0 x 0 1 0/1 12 13 1 # 2 1 5 # 3 4 6 E 001aae125 Fig 2. Logic symbol 001aae126 Fig 3. IEC logic symbol Y VEE VCC VCC VCC VCC from logic VEE VEE Z 001aad544 Fig 4. Schematic diagram (one switch) 74LV4053_4 Product data sheet (c) NXP B.V. 2009. All rights reserved. Rev. 04 -- 10 August 2009 3 of 26 74LV4053 NXP Semiconductors Triple single-pole double-throw analog switch 5. Pinning information 5.1 Pinning 74LV4053 3Y1 3 14 1Z 3Z 3Y0 E 13 1Y1 4 12 1Y0 5 11 S1 6 VEE 7 GND 8 10 S2 9 S3 74LV4053 Pin configuration SOT38-4 and SOT109-1 2 15 2Z 3Y1 3 14 1Z 13 1Y1 1 16 VCC 2Y0 2 15 2Z 3Z 4 3Y1 3 14 1Z 3Y0 5 3Z 4 13 1Y1 3Y0 5 12 1Y0 E 6 11 S1 VEE 7 10 S2 GND 8 001aak424 Fig 5. 2Y0 2Y1 9 S3 Pin configuration SOT338-1 and SOT403-1 E 6 VEE 7 12 1Y0 VCC (1) 11 S1 10 S2 001aak343 Transparent top view 001aak342 Fig 6. 16 VCC 15 2Z 9 2 S3 2Y0 terminal 1 index area 1 16 VCC 8 1 GND 2Y1 2Y1 74LV4053 Fig 7. Pin configuration for SOT763-1 5.2 Pin description Table 2. Pin description Symbol Pin Description E 6 enable input (active LOW) VEE 7 supply voltage GND 8 ground supply voltage S1, S2, S3 11, 10, 9 select input 1Y0, 2Y0, 3Y0 12, 2, 5 independent input or output 1Y1, 2Y1, 3Y1 13, 1, 3 independent input or output 1Z, 2Z, 3Z 14, 15, 4 common output or input VCC 16 supply voltage 74LV4053_4 Product data sheet (c) NXP B.V. 2009. All rights reserved. Rev. 04 -- 10 August 2009 4 of 26 74LV4053 NXP Semiconductors Triple single-pole double-throw analog switch 6. Functional description Table 3. Function table [1] Inputs Channel on E Sn L L nY0 to nZ L H nY1 to nZ H X switches off [1] H = HIGH voltage level; L = LOW voltage level; X = don't care. 7. Limiting values Table 4. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to VSS = 0 V (ground). Symbol Parameter Conditions supply voltage VCC Min Max Unit [1] -0.5 +7.0 V IIK input clamping current VI < -0.5 V or VI > VCC + 0.5 V [2] - 20 mA ISK switch clamping current VSW < -0.5 V or VSW > VCC + 0.5 V [2] - 20 mA ISW switch current VSW > -0.5 V or VSW < VCC + 0.5 V; source or sink current [2] - 25 mA Tstg storage temperature -65 +150 C Ptot total power dissipation Tamb = -40 C to +125 C [3] DIP16 package - 750 mW SO16 package - 500 mW TSSOP16 package - 500 mW DHVQFN16 package - 500 mW [1] To avoid drawing VCC current out of terminal nZ, when switch current flows into terminals nYn, the voltage drop across the bidirectional switch must not exceed 0.4 V. If the switch current flows into terminal nZ, no VCC current will flow out of terminals nYn, and in this case there is no limit for the voltage drop across the switch, but the voltages at nYn and nZ may not exceed VCC or VEE. [2] The minimum input voltage rating may be exceeded if the input current rating is observed. [3] For DIP16 packages: above 70 C the value of Ptot derates linearly with 12 mW/K. For SO16 packages: above 70 C the value of Ptot derates linearly with 8 mW/K. For SSOP16 and TSSOP16 packages: above 60 C the value of Ptot derates linearly with 5.5 mW/K. For DHVQFN16 packages: above 60 C the value of Ptot derates linearly with 4.5 mW/K. 74LV4053_4 Product data sheet (c) NXP B.V. 2009. All rights reserved. Rev. 04 -- 10 August 2009 5 of 26 74LV4053 NXP Semiconductors Triple single-pole double-throw analog switch 8. Recommended operating conditions Table 5. Recommended operating conditions Symbol Parameter Conditions Min Typ Max Unit VCC supply voltage see Figure 8 1 3.3 6 V VI input voltage 0 - VCC V VSW switch voltage 0 - VCC V Tamb ambient temperature -40 - +125 C t/V input transition rise and fall rate VCC = 1.0 V to 2.0 V - - 500 ns/V VCC = 2.0 V to 2.7 V - - 200 ns/V VCC = 2.7 V to 3.6 V - - 100 ns/V [1] in free air The static characteristics are guaranteed from VCC = 1.2 V to 6.0 V, but LV devices are guaranteed to function down to VCC = 1.0 V (with input levels GND or VCC). 001aak344 8.0 VCC - GND (V) 6.0 operating area 4.0 2.0 0 0 Fig 8. 2.0 4.0 6.0 8.0 VCC - VEE (V) Guaranteed operating area as a function of the supply voltages 74LV4053_4 Product data sheet (c) NXP B.V. 2009. All rights reserved. Rev. 04 -- 10 August 2009 6 of 26 74LV4053 NXP Semiconductors Triple single-pole double-throw analog switch 9. Static characteristics Table 6. Static characteristics At recommended operating conditions. Voltages are referenced to GND (ground = 0 V). Symbol Parameter HIGH-level input voltage VIH LOW-level input voltage VIL input leakage current II IS(OFF) IS(ON) OFF-state leakage current ON-state leakage current supply current ICC ICC additional supply current CI input capacitance Csw switch capacitance [1] Conditions -40 C to +85 C -40 C to +125 C Unit Min Typ[1] Max Min Max VCC = 1.2 V 0.9 - - 0.9 - V VCC = 2.0 V 1.4 - - 1.4 - V VCC = 2.7 V to 3.6 V 2.0 - - 2.0 - V VCC = 4.5 V 3.15 - - 3.15 - V VCC = 6.0 V 4.20 - - 4.20 - V VCC = 1.2 V - - 0.3 - 0.3 V VCC = 2.0 V - - 0.6 - 0.6 V VCC = 2.7 V to 3.6 V - - 0.8 - 0.8 V VCC = 4.5 V - - 1.35 - 1.35 V VCC = 6.0 V - - 1.80 - 1.80 V VCC = 3.6 V - - 1.0 - 1.0 A VCC = 6.0 V - - 2.0 - 2.0 A VCC = 3.6 V - - 1.0 - 1.0 A VCC = 6.0 V - - 2.0 - 2.0 A VCC = 3.6 V - - 1.0 - 1.0 A VCC = 6.0 V - - 2.0 - 2.0 A VCC = 3.6 V - - 20 - 40 A VCC = 6.0 V - - 40 - 80 A per input; VI = VCC - 0.6 V; VCC = 2.7 V to 3.6 V - - 500 - 850 A - 3.5 - - - pF independent pins nYn - 5 - - - pF common pins nZ - 8 - - - pF VI = VCC or GND VI = VIH or VIL; see Figure 9 VI = VIH or VIL; see Figure 10 VI = VCC or GND; IO = 0 A Typical values are measured at Tamb = 25 C. 74LV4053_4 Product data sheet (c) NXP B.V. 2009. All rights reserved. Rev. 04 -- 10 August 2009 7 of 26 74LV4053 NXP Semiconductors Triple single-pole double-throw analog switch 9.1 Test circuits VCC VIH or VIL VCC S1 to S3 nY0 1 nZ nY1 2 E IS S1 to S3 nY0 1 nZ nY1 2 IS GND = VEE GND VI VO switch E IS GND = VEE VCC VIH or VIL switch VO VI 001aak345 001aak346 VI = VCC or VEE and VO = VEE or VCC. VI = VCC or VEE and VO = open circuit. Fig 9. Test circuit for measuring OFF-state leakage current Fig 10. Test circuit for measuring ON-state leakage current 9.2 ON resistance Table 7. ON resistance At recommended operating conditions; voltages are referenced to GND (ground = 0 V); for graphs see Figure 11 and Figure 12. Symbol Parameter RON(peak) ON resistance (peak) -40 C to +85 C Conditions Min Max Min Max - - - - - - 180 365 - 435 VI = 0 V to VCC - VEE VCC = 1.2 V; ISW = 100 A [2] VCC = 2.0 V; ISW = 1000 A RON VCC = 2.7 V; ISW = 1000 A - 115 225 - 270 VCC = 3.0 V to 3.6 V; ISW = 1000 A - 100 200 - 245 VCC = 4.5 V; ISW = 1000 A - 75 150 - 180 VCC = 6.0 V; ISW = 1000 A - 70 140 - 165 - - - - - - 5 - - - ON resistance mismatch VI = 0 V to VCC - VEE between channels VCC = 1.2 V; ISW = 100 A [2] VCC = 2.0 V; ISW = 1000 A VCC = 2.7 V; ISW = 1000 A - 4 - - - VCC = 3.0 V to 3.6 V; ISW = 1000 A - 4 - - - VCC = 4.5 V; ISW = 1000 A - 3 - - - VCC = 6.0 V; ISW = 1000 A - 2 - - - 74LV4053_4 Product data sheet -40 C to +125 C Unit Typ[1] (c) NXP B.V. 2009. All rights reserved. Rev. 04 -- 10 August 2009 8 of 26 74LV4053 NXP Semiconductors Triple single-pole double-throw analog switch Table 7. ON resistance ...continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V); for graphs see Figure 11 and Figure 12. Symbol RON(rail) Parameter ON resistance (rail) -40 C to +85 C Conditions Min Max Min Max - 250 - - - VCC = 2.0 V; ISW = 1000 A - 120 280 - 325 VCC = 2.7 V; ISW = 1000 A - 75 170 - 195 VCC = 3.0 V to 3.6 V; ISW = 1000 A - 70 155 - 180 VCC = 4.5 V; ISW = 1000 A - 50 120 - 135 VCC = 6.0 V; ISW = 1000 A - 45 105 - 120 - 350 - - - VCC = 2.0 V; ISW = 1000 A - 170 340 - 400 VCC = 2.7 V; ISW = 1000 A - 105 210 - 250 VCC = 3.0 V to 3.6 V; ISW = 1000 A - 95 190 - 225 VCC = 4.5 V; ISW = 1000 A - 70 140 - 165 VCC = 6.0 V; ISW = 1000 A - 65 125 - 150 VI = GND VCC = 1.2 V; ISW = 100 A RON(rail) ON resistance (rail) -40 C to +125 C Unit Typ[1] [2] VI = VCC - VEE VCC = 1.2 V; ISW = 100 A [2] [1] Typical values are measured at Tamb = 25 C. [2] When supply voltages (VCC - VEE) near 1.2 V the analog switch ON resistance becomes extremely non-linear. When using a supply of 1.2 V, it is recommended to use these devices only for transmitting digital signals. 74LV4053_4 Product data sheet (c) NXP B.V. 2009. All rights reserved. Rev. 04 -- 10 August 2009 9 of 26 74LV4053 NXP Semiconductors Triple single-pole double-throw analog switch 9.3 On resistance waveform and test circuit V VSW VCC VIH or VIL S1 to S3 nY0 1 nZ nY1 2 switch E GND = VEE GND ISW VI 001aak347 RON = VSW / ISW. Fig 11. Test circuit for measuring RON 001aak348 200 VCC = 2.0 V RON () 150 VCC = 3.0 V 100 VCC = 4.5 V 50 0 0 1.2 2.4 3.6 4.8 VI (V) Vi = 0 V to VCC - VEE Fig 12. Typical RON as a function of input voltage 74LV4053_4 Product data sheet (c) NXP B.V. 2009. All rights reserved. Rev. 04 -- 10 August 2009 10 of 26 74LV4053 NXP Semiconductors Triple single-pole double-throw analog switch 10. Dynamic characteristics Table 8. Dynamic characteristics Voltages are referenced to GND (ground = 0 V). For test circuit see Figure 15. Symbol Parameter tpd -40 C to +85 C Conditions Min Max Min Max VCC = 1.2 V - 25 - - - ns VCC = 2.0 V - 9 17 - 20 ns - 6 13 - 15 ns - 5 10 - 12 ns - 4 9 - 10 ns - 3 7 - 8 ns VCC = 1.2 V - 100 - - - ns VCC = 2.0 V - 34 65 - 77 ns propagation delay nYn, nZ to nZ, nYn; see Figure 13 VCC = 3.0 V to 3.6 V [3] VCC = 4.5 V VCC = 6.0 V enable time E to nYn, nZ; see Figure 14 [2] VCC = 2.7 V - 25 48 - 56 ns VCC = 3.0 V to 3.6 V; CL = 15 pF [3] - 16 - - - ns VCC = 3.0 V to 3.6 V [3] - 19 38 - 45 ns - 17 32 - 38 ns - 13 25 - 29 ns VCC = 1.2 V - 125 - - - ns VCC = 2.0 V - 43 82 - 97 ns VCC = 4.5 V VCC = 6.0 V Sn to nYn, nZ; see Figure 14 [2] VCC = 2.7 V - 31 60 - 71 ns VCC = 3.0 V to 3.6 V; CL = 15 pF [3] - 20 - - - ns VCC = 3.0 V to 3.6 V [3] - 24 48 - 57 ns VCC = 4.5 V - 21 41 - 48 ns VCC = 6.0 V - 16 31 - 37 ns 74LV4053_4 Product data sheet Unit [2] VCC = 2.7 V ten -40 C to +125 C Typ[1] (c) NXP B.V. 2009. All rights reserved. Rev. 04 -- 10 August 2009 11 of 26 74LV4053 NXP Semiconductors Triple single-pole double-throw analog switch Table 8. Dynamic characteristics ...continued Voltages are referenced to GND (ground = 0 V). For test circuit see Figure 15. Symbol Parameter tdis disable time -40 C to +85 C Conditions Min Typ[1] VCC = 1.2 V - VCC = 2.0 V - E to nYn, nZ; see Figure 14 Min Max 95 - - - ns 34 61 - 73 ns - 26 46 - 54 ns VCC = 3.0 V to 3.6 V; CL = 15 pF - 17 - - - ns VCC = 3.0 V to 3.6 V [3] - 20 37 - 44 ns - 18 32 - 38 ns - 15 25 - 30 ns VCC = 1.2 V - 90 - - - ns VCC = 2.0 V - 32 59 - 70 ns VCC = 6.0 V Sn to nYn, nZ; see Figure 14 [2] VCC = 2.7 V - 24 44 - 52 ns VCC = 3.0 V to 3.6 V; CL = 15 pF [3] - 16 - - - ns VCC = 3.0 V to 3.6 V [3] - 19 36 - 42 ns - 17 31 - 36 ns - 14 24 - 28 ns - 36 - - - pF VCC = 4.5 V VCC = 6.0 V CL = 50 pF; fi = 1 MHz; VI = GND to VCC [1] All typical values are measured at Tamb = 25 C. [2] tpd is the same as tPLH and tPHL. ten is the same as tPZL and tPZH. tdis is the same as tPLZ and tPHZ. [3] Typical values are measured at nominal supply voltage (VCC = 3.3 V). [4] CPD is used to determine the dynamic power dissipation (PD in W). PD = CPD x VCC2 x fi x N + ((CL + CSW) x VCC2 x fo) where: fi = input frequency in MHz, fo = output frequency in MHz CL = output load capacitance in pF CSW = maximum switch capacitance in pF; VCC = supply voltage in Volts N = number of inputs switching (CL x VCC2 x fo) = sum of the outputs. [4] 74LV4053_4 Product data sheet Max [3] VCC = 4.5 V power dissipation capacitance Unit [2] VCC = 2.7 V CPD -40 C to +125 C (c) NXP B.V. 2009. All rights reserved. Rev. 04 -- 10 August 2009 12 of 26 74LV4053 NXP Semiconductors Triple single-pole double-throw analog switch 10.1 Waveforms VCC nYn or nZ input VM VEE tPLH tPHL VO nZ or nYn output VM VEE 001aak351 Measurement points are given in Table 9. VOL and VOH are typical voltage output levels that occur with the output load. Fig 13. nYn, nZ to nZ, nYn propagation delays VCC Sn, E input VM VSS tPLZ nYn or nZ output LOW-to-OFF OFF-to-LOW tPZL VO 90 % 10 % VEE tPHZ VO tPZH 90 % nYn or nZ output HIGH-to-OFF OFF-to-HIGH 10 % VEE switch ON switch OFF switch ON 001aak352 Measurement points are given in Table 9. VOL and VOH are typical voltage output levels that occur with the output load. Fig 14. Enable and disable times Table 9. Measurement points Supply voltage Input Output VCC VM VM VX VY < 2.7 V 0.5VCC 0.5VCC VOL + 0.1VCC VOH - 0.1VCC 2.7 V to 3.6 V 1.5 V 1.5 V VOL + 0.3 V VOH - 0.3 V > 3.6 V 0.5VCC 0.5VCC VOL + 0.1VCC VOH - 0.1VCC 74LV4053_4 Product data sheet (c) NXP B.V. 2009. All rights reserved. Rev. 04 -- 10 August 2009 13 of 26 74LV4053 NXP Semiconductors Triple single-pole double-throw analog switch VI tW 90 % negative pulse VM 0V tf tr tr tf VI 90 % positive pulse 0V VM 10 % VM VM 10 % tW VEXT VCC VI RL VO G DUT RT VEE CL RL 001aak353 Test data is given in Table 10. Definitions for test circuit: RL = Load resistance. CL = Load capacitance including jig and probe capacitance. RT = Termination resistance should be equal to output impedance Zo of the pulse generator. VEXT = External voltage for measuring switching times. Fig 15. Test circuit for measuring switching times Table 10. Test data Supply voltage Input VCC VI tr, tf Load CL RL VEXT tPHL, tPLH tPZH, tPHZ tPZL, tPLZ < 2.7 V VCC 6 ns 50 pF 1 k open VEE 2VCC 2.7 V to 3.6 V 2.7 V 6 ns 15 pF, 50 pF 1 k open VEE 2VCC > 3.6 V VCC 6 ns 50 pF 1 k open VEE 2VCC 74LV4053_4 Product data sheet (c) NXP B.V. 2009. All rights reserved. Rev. 04 -- 10 August 2009 14 of 26 74LV4053 NXP Semiconductors Triple single-pole double-throw analog switch 10.2 Additional dynamic parameters Table 11. Additional dynamic characteristics At recommended operating conditions; voltages are referenced to GND (ground = 0 V); VI = GND or VCC (unless otherwise specified); tr = tf 6.0 ns; Tamb = 25 C. Symbol Parameter Conditions THD fi = 1 kHz; CL = 50 pF; RL = 10 k; see Figure 20 total harmonic distortion Min Typ Max Unit VCC = 3.0 V; VI = 2.75 V (p-p) - 0.8 - % VCC = 6.0 V; VI = 5.5 V (p-p) - 0.4 - % fi = 10 kHz; CL = 50 pF; RL = 10 k; see Figure 20 f(-3dB) VCC = 3.0 V; VI = 2.75 V (p-p) - 2.4 - % VCC = 6.0 V; VI = 5.5 V (p-p) - 1.2 - % - 180 - MHz - 200 - MHz - -50 - dB - -50 - dB VCC = 3.0 V - 0.11 - V VCC = 6.0 V - 0.12 - V VCC = 3.0 V - -60 - dB VCC = 6.0 V - -60 - dB -3 dB frequency response CL = 50 pF; RL = 50 ; see Figure 16 isolation (OFF-state) fi = 1 MHz; CL = 50 pF; RL = 600 ; see Figure 18 [1] VCC = 3.0 V VCC = 6.0 V iso [2] VCC = 3.0 V VCC = 6.0 V crosstalk voltage Vct Xtalk crosstalk between digital inputs and switch; fi = 1 MHz; CL = 50 pF; RL = 600 ; see Figure 21 between switches; fi = 1 MHz; CL = 50 pF; RL = 600 ; see Figure 22 [1] Adjust fi voltage to obtain 0 dBm level at output for 1 MHz (0 dBm = 1 mW into 50 ). [2] Adjust fi voltage to obtain 0 dBm level at output for 1 MHz (0 dBm = 1 mW into 600 ). 74LV4053_4 Product data sheet [2] (c) NXP B.V. 2009. All rights reserved. Rev. 04 -- 10 August 2009 15 of 26 74LV4053 NXP Semiconductors Triple single-pole double-throw analog switch 10.2.1 Test circuits 001aak361 5 (dB) VCC VCC 0 VIH or VIL S1 to S3 nY0 1 nZ nY1 2 2RL switch E 0.1 F GND = VEE GND 2RL CL dB fi -5 10 102 103 104 105 106 f (kHz) 001aak355 VCC = 3.0 V; GND = 0 V; VEE = -3.0 V; RL = 50 ; RSOURCE = 1 k. Fig 16. Test circuit for measuring frequency response Fig 17. Typical frequency response 001aak360 0 (dB) VCC VCC -50 VIH or VIL 0.1 F VCC S1 to S3 nY0 1 nZ nY1 2 2RL switch E GND = VEE 2RL CL dB fi -100 10 102 103 104 105 106 f (kHz) 001aak356 VCC = 3.0 V; GND = 0 V; VEE = -3.0 V; RL = 50 ; RSOURCE = 1 k. Fig 18. Test circuit for measuring isolation (OFF-state) Fig 19. Typical isolation (OFF-state) as function of frequency 74LV4053_4 Product data sheet (c) NXP B.V. 2009. All rights reserved. Rev. 04 -- 10 August 2009 16 of 26 74LV4053 NXP Semiconductors Triple single-pole double-throw analog switch VCC VIH or VIL VCC S1 to S3 nY0 1 nZ nY1 2 2RL switch E 10 F GND = VEE GND 2RL CL D fi 001aak354 Fig 20. Test circuit for measuring total harmonic distortion VCC VCC VCC 2RL S1 to S3 nY0 1 nZ nY1 2 2RL switch E 2RL G GND = VEE VIH or VIL 2RL CL V VO 001aak357 a. Test circuit logic input (Sn, E) off on off Vct VO 001aaj908 b. Input and output pulse definitions VI may be connected to Sn or E. Fig 21. Test circuit for measuring crosstalk voltage between digital inputs and switch 74LV4053_4 Product data sheet (c) NXP B.V. 2009. All rights reserved. Rev. 04 -- 10 August 2009 17 of 26 74LV4053 NXP Semiconductors Triple single-pole double-throw analog switch VCC VCC VCC 2RL VIH or VIL RL S1 to S3 nY0 nZ nY1 2RL E 0.1 F GND = VEE GND 2RL VO CL 2RL dB VI 001aak358 a. Switch closed condition VCC VCC VCC 2RL VCC 2RL VIH or VIL S1 to S3 nY0 nZ nY1 2RL E GND = VEE GND RL 2RL VO VI 2RL CL dB 001aak359 b. Switch open condition Fig 22. Test circuit for measuring crosstalk between switches 74LV4053_4 Product data sheet (c) NXP B.V. 2009. All rights reserved. Rev. 04 -- 10 August 2009 18 of 26 74LV4053 NXP Semiconductors Triple single-pole double-throw analog switch 11. Package outline DIP16: plastic dual in-line package; 16 leads (300 mil) SOT38-4 ME seating plane D A2 A A1 L c e Z w M b1 (e 1) b b2 MH 9 16 pin 1 index E 1 8 0 5 10 mm scale DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT A max. A1 min. A2 max. b b1 b2 c D (1) E (1) e e1 L ME MH w Z (1) max. mm 4.2 0.51 3.2 1.73 1.30 0.53 0.38 1.25 0.85 0.36 0.23 19.50 18.55 6.48 6.20 2.54 7.62 3.60 3.05 8.25 7.80 10.0 8.3 0.254 0.76 inches 0.17 0.02 0.13 0.068 0.051 0.021 0.015 0.049 0.033 0.014 0.009 0.77 0.73 0.26 0.24 0.1 0.3 0.14 0.12 0.32 0.31 0.39 0.33 0.01 0.03 Note 1. Plastic or metal protrusions of 0.25 mm (0.01 inch) maximum per side are not included. OUTLINE VERSION REFERENCES IEC JEDEC JEITA EUROPEAN PROJECTION ISSUE DATE 95-01-14 03-02-13 SOT38-4 Fig 23. Package outline SOT38-4 (DIP16) 74LV4053_4 Product data sheet (c) NXP B.V. 2009. All rights reserved. Rev. 04 -- 10 August 2009 19 of 26 74LV4053 NXP Semiconductors Triple single-pole double-throw analog switch SO16: plastic small outline package; 16 leads; body width 3.9 mm SOT109-1 D E A X c y HE v M A Z 16 9 Q A2 A (A 3) A1 pin 1 index Lp 1 L 8 e 0 detail X w M bp 2.5 5 mm scale DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT A max. A1 A2 A3 bp c D (1) E (1) e HE L Lp Q v w y Z (1) mm 1.75 0.25 0.10 1.45 1.25 0.25 0.49 0.36 0.25 0.19 10.0 9.8 4.0 3.8 1.27 6.2 5.8 1.05 1.0 0.4 0.7 0.6 0.25 0.25 0.1 0.7 0.3 0.069 0.010 0.057 0.004 0.049 0.01 0.019 0.0100 0.39 0.014 0.0075 0.38 0.16 0.15 0.05 0.039 0.016 0.028 0.020 0.01 0.01 0.004 0.028 0.012 inches 0.244 0.041 0.228 o 8 o 0 Note 1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included. REFERENCES OUTLINE VERSION IEC JEDEC SOT109-1 076E07 MS-012 JEITA EUROPEAN PROJECTION ISSUE DATE 99-12-27 03-02-19 Fig 24. Package outline SOT109-1 (SO16) 74LV4053_4 Product data sheet (c) NXP B.V. 2009. All rights reserved. Rev. 04 -- 10 August 2009 20 of 26 74LV4053 NXP Semiconductors Triple single-pole double-throw analog switch SSOP16: plastic shrink small outline package; 16 leads; body width 5.3 mm D SOT338-1 E A X c y HE v M A Z 9 16 Q A2 A (A 3) A1 pin 1 index Lp L 8 1 detail X w M bp e 0 2.5 5 mm scale DIMENSIONS (mm are the original dimensions) UNIT A max. A1 A2 A3 bp c D (1) E (1) e HE L Lp Q v w y Z (1) mm 2 0.21 0.05 1.80 1.65 0.25 0.38 0.25 0.20 0.09 6.4 6.0 5.4 5.2 0.65 7.9 7.6 1.25 1.03 0.63 0.9 0.7 0.2 0.13 0.1 1.00 0.55 8 o 0 o Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT338-1 REFERENCES IEC JEDEC JEITA EUROPEAN PROJECTION ISSUE DATE 99-12-27 03-02-19 MO-150 Fig 25. Package outline SOT338-1 (SSOP16) 74LV4053_4 Product data sheet (c) NXP B.V. 2009. All rights reserved. Rev. 04 -- 10 August 2009 21 of 26 74LV4053 NXP Semiconductors Triple single-pole double-throw analog switch TSSOP16: plastic thin shrink small outline package; 16 leads; body width 4.4 mm SOT403-1 E D A X c y HE v M A Z 9 16 Q (A 3) A2 A A1 pin 1 index Lp L 1 8 detail X w M bp e 0 2.5 5 mm scale DIMENSIONS (mm are the original dimensions) UNIT A max. A1 A2 A3 bp c D (1) E (2) e HE L Lp Q v w y Z (1) mm 1.1 0.15 0.05 0.95 0.80 0.25 0.30 0.19 0.2 0.1 5.1 4.9 4.5 4.3 0.65 6.6 6.2 1 0.75 0.50 0.4 0.3 0.2 0.13 0.1 0.40 0.06 8 o 0 o Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic interlead protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT403-1 REFERENCES IEC JEDEC JEITA EUROPEAN PROJECTION ISSUE DATE 99-12-27 03-02-18 MO-153 Fig 26. Package outline SOT403-1 (TSSOP16) 74LV4053_4 Product data sheet (c) NXP B.V. 2009. All rights reserved. Rev. 04 -- 10 August 2009 22 of 26 74LV4053 NXP Semiconductors Triple single-pole double-throw analog switch DHVQFN16: plastic dual in-line compatible thermal enhanced very thin quad flat package; no leads; SOT763-1 16 terminals; body 2.5 x 3.5 x 0.85 mm A B D A A1 E c detail X terminal 1 index area terminal 1 index area C e1 e 2 7 y y1 C v M C A B w M C b L 1 8 Eh e 16 9 15 10 Dh X 0 2.5 5 mm scale DIMENSIONS (mm are the original dimensions) UNIT A(1) max. A1 b c D (1) Dh E (1) Eh e e1 L v w y y1 mm 1 0.05 0.00 0.30 0.18 0.2 3.6 3.4 2.15 1.85 2.6 2.4 1.15 0.85 0.5 2.5 0.5 0.3 0.1 0.05 0.05 0.1 Note 1. Plastic or metal protrusions of 0.075 mm maximum per side are not included. REFERENCES OUTLINE VERSION IEC JEDEC JEITA SOT763-1 --- MO-241 --- EUROPEAN PROJECTION ISSUE DATE 02-10-17 03-01-27 Fig 27. Package outline SOT763-1 (DHVQFN16) 74LV4053_4 Product data sheet (c) NXP B.V. 2009. All rights reserved. Rev. 04 -- 10 August 2009 23 of 26 74LV4053 NXP Semiconductors Triple single-pole double-throw analog switch 12. Abbreviations Table 12. Abbreviations Acronym Description CMOS Complementary Metal-Oxide Semiconductor ESD ElectroStatic Discharge HBM Human Body Model MM Machine Model TTL Transistor-Transistor Logic 13. Revision history Table 13. Revision history Document ID Release date Data sheet status Change notice Supersedes 74LV4053_4 20090810 Product data sheet - 74LV4053_3 Modifications: * The format of this data sheet has been redesigned to comply with the new identity guidelines of NXP Semiconductors. * * * * Legal texts have been adapted to the new company name where appropriate. Added type number 74LV4053BQ (DHVQFN16 package) RON values changed in Section 2. Package version SOT38-1 changed to SOT38-4 in Section 3, and Figure 23. 74LV4053_3 19980623 Product specification - 74LV4053_2 74LV4053_2 19970715 Product specification - - 74LV4053_4 Product data sheet (c) NXP B.V. 2009. All rights reserved. Rev. 04 -- 10 August 2009 24 of 26 74LV4053 NXP Semiconductors Triple single-pole double-throw analog switch 14. Legal information 14.1 Data sheet status Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification. [1] Please consult the most recently issued document before initiating or completing a design. [2] The term `short data sheet' is explained in section "Definitions". [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 14.2 Definitions Draft -- The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet -- A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. 14.3 Disclaimers General -- Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Right to make changes -- NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use -- NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in medical, military, aircraft, space or life support equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer's own risk. Applications -- Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Limiting values -- Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) may cause permanent damage to the device. Limiting values are stress ratings only and operation of the device at these or any other conditions above those given in the Characteristics sections of this document is not implied. Exposure to limiting values for extended periods may affect device reliability. Terms and conditions of sale -- NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, including those pertaining to warranty, intellectual property rights infringement and limitation of liability, unless explicitly otherwise agreed to in writing by NXP Semiconductors. In case of any inconsistency or conflict between information in this document and such terms and conditions, the latter will prevail. No offer to sell or license -- Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. Export control -- This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from national authorities. 14.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 15. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com 74LV4053_4 Product data sheet (c) NXP B.V. 2009. All rights reserved. Rev. 04 -- 10 August 2009 25 of 26 74LV4053 NXP Semiconductors Triple single-pole double-throw analog switch 16. Contents 1 2 3 4 5 5.1 5.2 6 7 8 9 9.1 9.2 9.3 10 10.1 10.2 10.2.1 11 12 13 14 14.1 14.2 14.3 14.4 15 16 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Functional diagram . . . . . . . . . . . . . . . . . . . . . . 2 Pinning information . . . . . . . . . . . . . . . . . . . . . . 4 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 4 Functional description . . . . . . . . . . . . . . . . . . . 5 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 5 Recommended operating conditions. . . . . . . . 6 Static characteristics. . . . . . . . . . . . . . . . . . . . . 7 Test circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 ON resistance . . . . . . . . . . . . . . . . . . . . . . . . . . 8 On resistance waveform and test circuit . . . . . 10 Dynamic characteristics . . . . . . . . . . . . . . . . . 11 Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Additional dynamic parameters . . . . . . . . . . . 15 Test circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 19 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 24 Legal information. . . . . . . . . . . . . . . . . . . . . . . 25 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 25 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Contact information. . . . . . . . . . . . . . . . . . . . . 25 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section `Legal information'. (c) NXP B.V. 2009. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 10 August 2009 Document identifier: 74LV4053_4