LP3470 LP3470 Tiny Power On Reset Circuit Literature Number: SNVS003E LP3470 Tiny Power On Reset Circuit General Description Key Specifications The LP3470 is a micropower CMOS voltage supervisory circuit designed to monitor power supplies in microprocessor (P) and other digital systems. It provides maximum adjustability for power-on-reset (POR) and supervisory functions. It is available in the following six standard reset threshold voltage (VRTH) options: 2.63V, 2.93V, 3.08V, 3.65V, 4.00V, 4.38V, and 4.63V. If other voltage options between 2.4V and 5.0V are desired please contact your National Semiconductor representative. The LP3470 asserts a reset signal whenever the V CC supply voltage falls below a reset threshold. The reset time-out period is adjustable using an external capacitor. Reset remains asserted for an interval (programmed by an external capacitor) after VCC has risen above the threshold voltage. The device is available in the tiny SOT23-5 package. 1% Reset Threshold Accuracy Over Temperature Standard Reset Threshold Voltages: 2.63V, 2.93V, 3.08V, 3.65V, 4.00V, 4.38V, and 4.63V Custom Reset Threshold Voltages: For other voltages between 2.4V and 5.0V contact your National Semiconductor representative Very Low Quiescent Current (16 A typical) Guaranteed Reset valid down to VCC=0.5V Features Tiny SOT23-5 Package Open Drain Reset Output Programmable Reset Timeout Period Using an External Capacitor Immune to Short VCC Transients Applications Critical P and C Power Monitoring Intelligent Instruments Computers Portable/Battery-Powered Equipments Pin Configuration and Basic Operating Circuit Pin Configuration Basic Operating Circuit 10001602 Top View See NS Package Number MF05A 10001601 (c) 2009 National Semiconductor Corporation 100016 www.national.com LP3470 Tiny Power On Reset Circuit September 3, 2009 LP3470 Ordering Information Operating Temperature Range Nominal VRTH (V) 2.63 2.93 -20C to +85C 3.08 4.00 4.38 4.63 2.63 2.75 2.83 2.93 -40C to +85C 3.08 3.65 4.00 4.38 4.63 4.80 www.national.com Order Number Package Marking Package Type Supplied As LP3470M5-2.63 D25B SOT23-5 1000 Units on Tape and Reel LP3470M5X-2.63 D25B SOT23-5 3000 Units on Tape and Reel LP3470M5-2.93 D26B SOT23-5 1000 Units on Tape and Reel LP3470M5X-2.93 D26B SOT23-5 3000 Units on Tape and Reel LP3470M5-3.08 D28B SOT23-5 1000 Units on Tape and Reel LP3470M5X-3.08 D28B SOT23-5 3000 Units on Tape and Reel LP3470M5-4.00 D29B SOT23-5 1000 Units on Tape and Reel LP3470M5X-4.00 D29B SOT23-5 3000 Units on Tape and Reel LP3470M5-4.38 D30B SOT23-5 1000 Units on Tape and Reel LP3470M5X-4.38 D30B SOT23-5 3000 Units on Tape and Reel LP3470M5-4.63 D31B SOT23-5 1000 Units on Tape and Reel LP3470M5X-4.63 D31B SOT23-5 3000 Units on Tape and Reel LP3470IM5-2.63 D25C SOT23-5 1000 Units on Tape and Reel LP3470IM5X-2.63 D25C SOT23-5 3000 Units on Tape and Reel LP3470IM5-2.75 D38C SOT23-5 1000 Units on Tape and Reel LP3470IM5-2.83 D39C SOT23-5 1000 Units on Tape and Reel LP3470IM5X-2.83 D39C SOT23-5 3000 Units on Tape and Reel LP3470IM5-2.93 D26C SOT23-5 1000 Units on Tape and Reel LP3470IM5X-2.93 D26C SOT23-5 3000 Units on Tape and Reel LP3470IM5-3.08 D28C SOT23-5 1000 Units on Tape and Reel LP3470IM5X-3.08 D28C SOT23-5 3000 Units on Tape and Reel LP3470IM5-3.65 D37C SOT23-5 1000 Units on Tape and Reel LP3470IM5X-3.65 D37C SOT23-5 3000 Units on Tape and Reel LP3470IM5-4.00 D29C SOT23-5 1000 Units on Tape and Reel LP3470IM5X-4.00 D29C SOT23-5 3000 Units on Tape and Reel LP3470IM5-4.38 D30C SOT23-5 1000 Units on Tape and Reel LP3470IM5X-4.38 D30C SOT23-5 3000 Units on Tape and Reel LP3470IM5-4.63 D31C SOT23-5 1000 Units on Tape and Reel LP3470IM5X-4.63 D31C SOT23-5 3000 Units on Tape and Reel LP3470IM5X-4.8 D15C SOT23-5 1000 Units on Tape and Reel 2 If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. VCC Voltage Reset Voltage Output Current (Reset) Operating Temperature Range LP3470 -40C to +85C 125C 300 mW JA (Note 2) Storage Temp. Range Lead Temp. (Soldering, 5 sec) ESD Rating (Note 3) -0.3V to +6V -0.3V to +6V 10 mA 280C/W -65C to +150C 260C 2 kV -20C to +85C Electrical Characteristics Limits in standard typeface are for TJ = 25C, and limits in boldface type apply over the full operating temperature range, unless otherwise specified. VCC = +2.4V to +5.0V unless otherwise noted. Symbol Parameter Conditions Typ Min (Note 4) (Note 5) Max (Note 5) Units VCC Operating Voltage Range ICC VCC Supply Current VCC = 4.5V VRTH Reset Threshold Voltage (Note 6) LP3470 VRTH 0.99 VRTH 0.99 VRTH 1.01 VRTH 1.01 VRTH LP3470I VRTH 0.99 VRTH 0.985 VRTH 1.01 VRTH 1.015 VRTH 35 15 65 mV 300 s 3.5 ms 0.5 16 5.5 V 30 A VHYST Hysteresis Voltage (Note 7) tPD VCC to Reset Delay VCC falling at 1 mV/s tRP Reset Timeout Period (Note 8) C1 = 1 nF VOL Reset Output Voltage Low VCC = 0.5V; IOL = 30 A 0.1 VCC = 1.0V; IOL = 100 A 0.1 VCC =VRTH -100 mV; IOL = 4 mA 0.4 R1 External Pull-up Resistor ILEAK Reset Output Leakage Current 100 2 20 0.15 1.0 0.68 V V 68 k 1 6 A Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Electrical specifications do not apply when operating the device beyond its operating conditions. Note 2: The maximum power dissipation must be derated at elevated temperatures and is dictated by TJmax (Maximum Junction Temperature), JA (Junction to Ambient Thermal Resistance), and TA (Ambient Temperature). The maximum allowable power dissipation at any temperature is PDmax = (TJmax - TA)/ JA or the number given in the Absolute Maximum Ratings, whichever is lower. Note 3: The Human Body Model is a 100 pF capacitor discharged through a 1.5 k resistor into each pin. Note 4: Typical numbers are at 25C and represent the most likely parametric norm. Note 5: Min. and Max. limits in standard typeface are 100% production tested at 25C. Min. and Max. limits in boldface are guaranteed through correlation using Statistical Quality Control (SQC) methods. The limits are used to calculate National's Average Outgoing Quality Level (AOQL). Note 6: Factory-trimmed reset thresholds are available in 50 mV increments from 2.4V to 5.0V. Contact your National Semiconductor representative. Note 7: VHYST affects the relation between VCC and Reset as shown in the timing diagram. Note 8: tRP is programmable by varying the value of the external capacitor (C1) connected to pin SRT. The equation is: tRP = 2000 x C1 (C1 in F and tRP in ms). 3 www.national.com LP3470 LP3470I Junction Temperature (TJmax) Power Dissipation (TA = 25C) (Note 2) Absolute Maximum Ratings (Note 1) LP3470 Typical Operating Characteristics TA = +25C, unless otherwise specified. ICC vs Temperature ICC vs VCC 10001610 10001611 VCC to Reset Delay vs Temp Normalized tRP vs Temp. 10001613 10001612 Normalized VRTH vs Temp. Transient Rejection 10001608 10001606 www.national.com 4 LP3470 VHYST vs VRTH VHYST vs Temperature 10001609 10001614 Pin Descriptions Pin Name Function 1 SRT Set Reset Time-out Input. Connect a capacitor between this input and ground to select the Reset Timeout period (tRP). tRP = 2000 x C1 (C1 in F and tRP in ms). If no capacitor is connected, leave this pin floating. 2 GND Ground pin. 3 VCC1 Always connect to pin VCC (Pin 4). 4 VCC Supply voltage, and reset threshold monitor input. 5 Reset Open-Drain, Active-Low reset output. Connect to an external pull-up resistor. Reset changes from high to low whenever the monitored voltage (VCC) drops below the reset threshold voltage (VRTH). Once VCC exceeds VRTH, Reset remains low for the reset timeout period (tRP) and then goes high. Functional Block Diagram 10001603 5 www.national.com LP3470 Application Information the reset threshold, Reset remains low for a time period tRP before going to logic high. RESET TIMEOUT PERIOD The Reset Timeout Period (tRP) is programmable using an external capacitor (C1) connected to pin SRT of LP3470. A Ceramic chip capacitor rated at or above 10V is sufficient. The Reset Timeout Period (tRP) can be calculated using the following formula: PULL-UP RESISTOR SELECTION The LP3470's Reset output structure is a simple open-drain N-channel MOSFET switch. A pull-up resistor (R1) should be connected to VCC. R1 should be large enough to limit the current through the output MOSFET (Q1) below 10 mA. A resistor value of more than 680 guarantees this. R1 should also be small enough to ensure a logic high while supplying all the leakage current through the Reset pin. A resistor value of less than 68k satisfies this condition. A typical pull-up resistor value of 20 k is sufficient in most applications. tRP (ms) = 2000 x C1 (F). For example a C1 of 100 nF will achieve a tRP of 200 ms. If no delay due to tRP is needed in a certain application, the pin SRT should be left floating. RESET OUTPUT In applications like microprocessor (P) systems, errors might occur in system operation during power-up, power-down, or brownout conditions. It is imperative to monitor the power supply voltage in order to prevent these errors from occurring. The LP3470 asserts a reset signal whenever the V CC supply voltage is below a threshold (VRTH) voltage. Reset is guaranteed to be a logic low for VCC > 0.5V. Once VCC exceeds the reset threshold, the reset is kept asserted for a time period (tRP) programmed by an external capacitor (C1); after this interval Reset goes to logic high. If a brownout condition occurs (monitored voltage falls below the reset threshold minus a small hysteresis), Reset goes low. When VCC returns above NEGATIVE-GOING VCC TRANSIENTS The LP3470 is relatively immune to short duration negativegoing VCC transients (glitches). The Typical Operating Characteristics show the Maximum Transient Duration vs. Negative Transient Amplitude (graph titled Transient Rejection), for which reset pulses are not generated. This graph shows the maximum pulse width a negative-going VCC transient may typically have without causing a reset pulse to be issued. As the transient amplitude increases (i.e. goes farther below the reset threshold), the maximum allowable pulse width decreases. A 0.1 F bypass capacitor mounted close to VCC provides additional transient immunity. Timing Diagram 10001604 www.national.com 6 LP3470 Typical Application Circuit 10001605 7 www.national.com LP3470 Physical Dimensions inches (millimeters) unless otherwise noted 5-Lead Small Outline Package (M5) For Ordering Information See Ordering Information Table In This Data Sheet NSPackage Number MF05A www.national.com 8 LP3470 Notes 9 www.national.com LP3470 Tiny Power On Reset Circuit Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: Products Design Support Amplifiers www.national.com/amplifiers WEBENCH(R) Tools www.national.com/webench Audio www.national.com/audio App Notes www.national.com/appnotes Clock and Timing www.national.com/timing Reference Designs www.national.com/refdesigns Data Converters www.national.com/adc Samples www.national.com/samples Interface www.national.com/interface Eval Boards www.national.com/evalboards LVDS www.national.com/lvds Packaging www.national.com/packaging Power Management www.national.com/power Green Compliance www.national.com/quality/green Switching Regulators www.national.com/switchers Distributors www.national.com/contacts LDOs www.national.com/ldo Quality and Reliability www.national.com/quality LED Lighting www.national.com/led Feedback/Support www.national.com/feedback Voltage Reference www.national.com/vref Design Made Easy www.national.com/easy www.national.com/powerwise Solutions www.national.com/solutions Mil/Aero www.national.com/milaero PowerWise(R) Solutions Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors SolarMagicTM www.national.com/solarmagic Wireless (PLL/VCO) www.national.com/wireless www.national.com/training PowerWise(R) Design University THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION ("NATIONAL") PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL'S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright(c) 2009 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: support@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: europe.support@nsc.com National Semiconductor Asia Pacific Technical Support Center Email: ap.support@nsc.com National Semiconductor Japan Technical Support Center Email: jpn.feedback@nsc.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated