Single-Channel: 6N137, HCPL2601, HCPL2611 Dual-Channel: HCPL2630, HCPL2631 High Speed 10MBit/s Logic Gate Optocouplers Features Description The 6N137, HCPL2601, HCPL2611 single-channel and HCPL2630, HCPL2631 dual-channel optocouplers consist of a 850 nm AlGaAS LED, optically coupled to a very high speed integrated photo-detector logic gate with a strobable output. This output features an open collector, thereby permitting wired OR outputs. The coupled parameters are guaranteed over the temperature range of -40C to +85C. A maximum input signal of 5mA will provide a minimum output sink current of 13mA (fan out of 8). Very high speed - 10 MBit/s Superior CMR - 10 kV/s Double working voltage-480V Fan-out of 8 over -40C to +85C Logic gate output Strobable output Wired OR-open collector U.L. recognized (File # E90700) Applications An internal noise shield provides superior common mode rejection of typically 10kV/s. The HCPL2601 and HCPL2631 has a minimum CMR of 5kV/s. The HCPL2611 has a minimum CMR of 10kV/s. Ground loop elimination LSTTL to TTL, LSTTL or 5-volt CMOS Line receiver, data transmission Data multiplexing Switching power supplies Pulse transformer replacement Computer-peripheral interface Schematics Package Outlines 8 VCC N/C 1 8 8 VCC + 1 1 VF1 + 2 7 VE _ 2 6 VO _ 7 V01 VF _ 8 3 V 5 GND N/C 4 6N137 HCPL2601 HCPL2611 6 V02 3 8 1 1 F2 5 GND + 4 HCPL2630 HCPL2631 A 0.1F bypass capacitor must be connected between pins 8 and 5(1). (c)2005 Fairchild Semiconductor Corporation 6N137, HCPL2601, HCPL2611, HCPL2630, HCPL2631 Rev. 1.0.7 Truth Table (Positive Logic) Input Enable Output H H L L H H H L H L L H H NC L L NC H www.fairchildsemi.com Single-Channel: 6N137, HCPL2601, HCPL2611 Dual-Channel: HCPL2630, HCPL2631 -- High Speed 10MBit/s Logic Gate Optocouplers August 2008 Symbol Parameter Value Units TSTG Storage Temperature -55 to +125 C TOPR Operating Temperature -40 to +85 C TSOL Lead Solder Temperature 260 for 10 sec C mA EMITTER IF DC/Average Forward Single Channel 50 Input Current Dual Channel (Each Channel) 30 VE Enable Input Voltage Not to Exceed VCC by more than 500mV Single Channel 5.5 V VR Reverse Input Voltage Each Channel 5.0 V PI Power Dissipation Single Channel 100 mW Dual Channel (Each Channel) 45 DETECTOR Supply Voltage VCC (1 minute max) 7.0 V 50 mA IO Output Current Dual Channel (Each Channel) 50 VO Output Voltage Each Channel 7.0 V PO Collector Output Single Channel 85 mW Power Dissipation Dual Channel (Each Channel) 60 Single Channel Recommended Operating Conditions The Recommended Operating Conditions table defines the conditions for actual device operation. Recommended operating conditions are specified to ensure optimal performance to the datasheet specifications. Fairchild does not recommend exceeding them or designing to absolute maximum ratings. Symbol Parameter Min. Max. Units IFL Input Current, Low Level 0 250 A IFH Input Current, High Level *6.3 15 mA VCC Supply Voltage, Output 4.5 5.5 V VEL Enable Voltage, Low Level 0 0.8 V VEH Enable Voltage, High Level 2.0 VCC V TA Low Level Supply Current -40 +85 C N Fan Out (TTL load) 8 *6.3mA is a guard banded value which allows for at least 20% CTR degradation. Initial input current threshold value is 5.0mA or less. (c)2005 Fairchild Semiconductor Corporation 6N137, HCPL2601, HCPL2611, HCPL2630, HCPL2631 Rev. 1.0.7 www.fairchildsemi.com 2 Single-Channel: 6N137, HCPL2601, HCPL2611 Dual-Channel: HCPL2630, HCPL2631 -- High Speed 10MBit/s Logic Gate Optocouplers Absolute Maximum Ratings (TA = 25C unless otherwise specified) Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings are stress ratings only. Individual Component Characteristics Symbol Parameter Test Conditions Min. Typ.* Max. Unit 1.8 V EMITTER VF Input Forward Voltage IF = 10mA BVR Input Reverse Breakdown Voltage IR = 10A CIN Input Capacitance VF = 0, f = 1MHz Input Diode Temperature Coefficient IF = 10mA ICCH High Level Supply Current VCC = 5.5V, IF = 0mA, VE = 0.5V Single Channel 7 10 Dual Channel 10 15 ICCL Low Level Supply Current Single Channel VCC = 5.5V, IF = 10mA 9 13 Dual Channel VE = 0.5V IEL Low Level Enable Current VCC = 5.5V, VE = 0.5V IEH High Level Enable Current VCC = 5.5V, VE = 2.0V VEH High Level Enable Voltage VCC = 5.5V, IF = 10mA TA = 25C VF / TA 1.4 1.75 5.0 V 60 pF -1.4 mV/C DETECTOR VEL Low Level Enable Voltage VCC = 5.5V, IF = 10mA mA mA 14 21 -0.8 -1.6 mA -0.6 -1.6 mA 2.0 V (3) 0.8 V Switching Characteristics (TA = -40C to +85C, VCC = 5V, IF = 7.5mA unless otherwise specified) Symbol TPLH TPHL AC Characteristics Test Conditions Propagation Delay Time to Output HIGH Level RL = 350, CL = 15pF(4) (Fig. 12) Propagation Delay Time to Output LOW Level TA = 25C(5) |TPHL-TPLH| Pulse Width Distortion TA = 25C Min. Typ.* 20 45 Max. Unit 75 ns 100 25 45 RL = 350, CL = 15pF (Fig. 12) 75 ns 100 (RL = 350, CL = 15pF (Fig. 12) 3 35 ns tr Output Rise Time (10-90%) RL = 350, CL = 15pF (Fig. 12) 50 ns tf Output Rise Time (90-10%) RL = 350, CL = 15pF(7) (Fig. 12) 12 ns tELH Enable Propagation Delay Time to Output HIGH Level IF = 7.5mA, VEH = 3.5V, RL = 350, CL = 15pF(8) (Fig. 13) 20 ns tEHL Enable Propagation Delay Time to Output LOW Level IF = 7.5mA, VEH = 3.5V, RL = 350, CL = 15pF(9) (Fig. 13) 20 ns Common Mode Transient Immunity (at Output HIGH Level) TA = 25C, |VCM| = 50V 6N137, HCPL2630 (Peak), IF = 0mA, HCPL2601, HCPL2631 VOH (Min.) = 2.0V, RL = 350(10) (Fig. 14) 10,000 V/s Common Mode Transient Immunity (at Output LOW Level) RL = 350, IF = 7.5mA, 6N137, HCPL2630 VOL (Max.) = 0.8V, HCPL2601, HCPL2631 TA = 25C(11) (Fig. 14) |CMH| |VCM| = 400V |CML| HCPL2611 |VCM| = 400V (c)2005 Fairchild Semiconductor Corporation 6N137, HCPL2601, HCPL2611, HCPL2630, HCPL2631 Rev. 1.0.7 (6) HCPL2611 5000 10,000 10,000 15,000 V/s 10,000 5000 10,000 10,000 15,000 www.fairchildsemi.com 3 Single-Channel: 6N137, HCPL2601, HCPL2611 Dual-Channel: HCPL2630, HCPL2631 -- High Speed 10MBit/s Logic Gate Optocouplers Electrical Characteristics (TA = 0 to 70C unless otherwise specified) Transfer Characteristics (TA = -40 to +85C unless otherwise specified) Symbol DC Characteristics Test Conditions Min. Typ.* Max. Unit 100 A IOH HIGH Level Output Current VCC = 5.5V, VO = 5.5V, IF = 250A, VE = 2.0V(2) VOL LOW Level Output Current VCC = 5.5V, IF = 5mA, VE = 2.0V, ICL = 13mA(2) .35 0.6 V IFT Input Threshold Current VCC = 5.5V, VO = 0.6V, VE = 2.0V, IOL = 13mA 3 5 mA Max. Unit 1.0* A Isolation Characteristics (TA = -40C to +85C unless otherwise specified.) Symbol II-O Characteristics Test Conditions Min. Typ.* Input-Output Insulation Leakage Current Relative humidity = 45%, TA = 25C, t = 5s, VI-O = 3000 VDC(12) VISO Withstand Insulation Test Voltage RH < 50%, TA = 25C, II-O 2A, t = 1 min.(12) RI-O Resistance (Input to Output) VI-O = 500V(12) 1012 Capacitance (Input to Output) 1MHz(12) 0.6 pF CI-O f= 2500 VRMS *All Typicals at VCC = 5V, TA = 25C Notes: 1. The VCC supply to each optoisolator must be bypassed by a 0.1F capacitor or larger. This can be either a ceramic or solid tantalum capacitor with good high frequency characteristic and should be connected as close as possible to the package VCC and GND pins of each device. 2. Each channel. 3. Enable Input - No pull up resistor required as the device has an internal pull up resistor. 4. tPLH - Propagation delay is measured from the 3.75mA level on the HIGH to LOW transition of the input current pulse to the 1.5 V level on the LOW to HIGH transition of the output voltage pulse. 5. tPHL - Propagation delay is measured from the 3.75mA level on the LOW to HIGH transition of the input current pulse to the 1.5 V level on the HIGH to LOW transition of the output voltage pulse. 6. tr - Rise time is measured from the 90% to the 10% levels on the LOW to HIGH transition of the output pulse. 7. tf - Fall time is measured from the 10% to the 90% levels on the HIGH to LOW transition of the output pulse. 8. tELH - Enable input propagation delay is measured from the 1.5V level on the HIGH to LOW transition of the input voltage pulse to the 1.5V level on the LOW to HIGH transition of the output voltage pulse. 9. tEHL - Enable input propagation delay is measured from the 1.5V level on the LOW to HIGH transition of the input voltage pulse to the 1.5V level on the HIGH to LOW transition of the output voltage pulse. 10. CMH - The maximum tolerable rate of rise of the common mode voltage to ensure the output will remain in the HIGH state (i.e., VOUT > 2.0V). Measured in volts per microsecond (V/s). 11. CML - The maximum tolerable rate of rise of the common mode voltage to ensure the output will remain in the LOW output state (i.e., VOUT < 0.8V). Measured in volts per microsecond (V/s). 12. Device considered a two-terminal device: Pins 1, 2, 3 and 4 shorted together, and Pins 5, 6, 7 and 8 shorted together. (c)2005 Fairchild Semiconductor Corporation 6N137, HCPL2601, HCPL2611, HCPL2630, HCPL2631 Rev. 1.0.7 www.fairchildsemi.com 4 Single-Channel: 6N137, HCPL2601, HCPL2611 Dual-Channel: HCPL2630, HCPL2631 -- High Speed 10MBit/s Logic Gate Optocouplers Electrical Characteristics (Continued) Fig. 2 Input Diode Forward Voltage vs. Forward Current Conditions: IF = 5 mA VE = 2 V VCC = 5.5V 0.7 0.6 IOL = 12.8 mA 0.5 IOL = 16mA 0.4 0.3 IOL = 6.4mA 0.2 IOL = 9.6mA 0.1 30 16 10 IF - FORWARD CURRENT (mA) VOL - LOW LEVEL OUTPUT VOLTAGE (V) Fig.1 Low Level Output Voltage vs. Ambient Temperature 0.8 1 0.1 0.01 0.001 0.0 -40 -20 0 20 40 60 80 0.9 1.0 1.1 TA - AMBIENT TEMPERATURE (C) IOL - LOW LEVEL OUTPUT CURRENT (mA) TP - PROPAGATION DELAY (ns) VCC = 5 V 100 RL = 4 k (TPLH) 80 60 RL = 1 k (TPLH) 40 0 RL = 350 (TPLH) 5 7 RL = 1 k RL = 4 k (TPHL) RL = 350 k 9 11 13 15 50 1.5 1.6 IF = 15mA IF = 10mA 40 IF = 5mA 35 30 Conditions: VCC = 5 V VE = 2 V VOL = 0.6 V 25 20 -40 -20 0 20 40 60 80 TA - AMBIENT TEMPERATURE (C) Fig. 6 Output Voltage vs. Input Forward Current Fig. 5 Input Threshold Current vs. Ambient Temperature 6 Conditions: VCC = 5.0 V VO = 0.6 V VO - OUTPUT VOLTAGE (V) IFT - INPUT THRESHOLD CURRENT (mA) 1.4 45 IF - FORWARD CURRENT (mA) 4 1.3 Fig. 4 Low Level Output Current vs. Ambient Temperature Fig.3 Switching Time vs. Forward Current 120 20 1.2 VF - FORWARD VOLTAGE (V) 3 RL = 350 RL = 1k 2 RL = 4k 5 RL = 350 4 RL = 4k RL = 1k 3 2 1 1 -40 0 -20 0 20 40 60 0 80 (c)2005 Fairchild Semiconductor Corporation 6N137, HCPL2601, HCPL2611, HCPL2630, HCPL2631 Rev. 1.0.7 1 2 3 4 5 6 IF - FORWARD CURRENT (mA) TA - AMBIENT TEMPERATURE (C) www.fairchildsemi.com 5 Single-Channel: 6N137, HCPL2601, HCPL2611 Dual-Channel: HCPL2630, HCPL2631 -- High Speed 10MBit/s Logic Gate Optocouplers Typical Performance Curves Fig. 8 Rise and Fall Time vs. Temperature Fig. 7 Pulse Width Distortion vs. Temperature 600 RL = 4 k Tr/Tf - RISE AND FALL TIME (ns) PWD - PULSE WIDTH DISTORTION (ns) 80 60 Conditions: IF = 7.5mA VCC = 5A 40 20 RL = 1 k 0 -60 RL = 350 -40 -20 0 20 40 60 80 RL = 4 k (tr) 500 400 Conditions: IF = 7.5 mA VCC = 5 V 300 200 RL = 1 k (tr) 100 RL = 350 (tr) 0 -60 100 -40 -20 TA - TEMPERATURE (C) Fig. 9 Enable Propagation Delay vs. Temperature 40 60 20 80 100 Fig. 10 Switching Time vs. Temperature 120 TP - PROPAGATION DELAY (ns) TE - ENABLE PROPAGATION DELAY (ns) (tf) TA - TEMPERATURE (C) 120 100 RL = 4 k (TELH) 80 60 40 RL = 1 k (TELH) RL = 350 (TELH) 20 0 -60 0 RL = 1 k RL = 4 k RL = 350 RL = 350 RL = 1 k RL = 4 k -40 -20 0 20 40 60 RL = 4 k TPLH 100 80 60 RL = 1 k TPLH 40 RL = 350 TPLH RL = 1 k RL = 4 k RL = 350 (TEHL) 80 20 -60 100 -40 -20 TA - TEMPERATURE (C) 0 20 40 60 TPHL 80 100 TA - TEMPERATURE (C) IOH - HIGH LEVEL OUTPUT CURRENT (A) Fig. 11 High Level Output Current vs. Temperature 20 Conditions: VCC = 5.5 V VO = 5.5 V VE = 2.0 V IF = 250 A 15 10 5 0 -60 -40 -20 0 20 40 60 80 100 TA - TEMPERATURE (C) (c)2005 Fairchild Semiconductor Corporation 6N137, HCPL2601, HCPL2611, HCPL2630, HCPL2631 Rev. 1.0.7 www.fairchildsemi.com 6 Single-Channel: 6N137, HCPL2601, HCPL2611 Dual-Channel: HCPL2630, HCPL2631 -- High Speed 10MBit/s Logic Gate Optocouplers Typical Performance Curves (Continued) Pulse Generator tr = 5ns Z O = 50 +5V IF = 7.5 mA 1 VCC IF = 3.75 mA 8 Input (IF ) 7 Output (VO ) t PHL 2 Input Monitor (I F) .1 f bypass RL Output (VO ) 6 3 CL 47 4 GND tPLH 1.5 V 90% Output (VO ) 10% 5 tf tr Fig. 12 Test Circuit and Waveforms for tPLH, tPHL, tr and tf Pulse Generator tr = 5ns Z O = 50 Input Monitor (V E) +5V 3.0 V Input (VE ) VCC 1 8 1.5 V t EHL 7.5 mA 7 2 .1 f bypass RL 1.5 V Output (VO ) 6 3 t ELH Output (VO ) CL 4 GND 5 Fig. 13 Test Circuit tEHL and tELH (c)2005 Fairchild Semiconductor Corporation 6N137, HCPL2601, HCPL2611, HCPL2630, HCPL2631 Rev. 1.0.7 www.fairchildsemi.com 7 Single-Channel: 6N137, HCPL2601, HCPL2611 Dual-Channel: HCPL2630, HCPL2631 -- High Speed 10MBit/s Logic Gate Optocouplers Test Circuits VCC IF A 1 8 2 7 3 6 +5V .1 f bypass 350 B VFF 4 GND Output (VO) 5 VCM Pulse Gen Peak VCM 0V CM H 5V Switching Pos. (A), IF = 0 VO VO (Min) VO (Max) Switching Pos. (B), I F = 7.5 mA VO 0.5 V CM L Fig. 14 Test Circuit Common Mode Transient Immunity (c)2005 Fairchild Semiconductor Corporation 6N137, HCPL2601, HCPL2611, HCPL2630, HCPL2631 Rev. 1.0.7 www.fairchildsemi.com 8 Single-Channel: 6N137, HCPL2601, HCPL2611 Dual-Channel: HCPL2630, HCPL2631 -- High Speed 10MBit/s Logic Gate Optocouplers Test Circuits (Continued) Through Hole 0.4" Lead Spacing PIN 1 ID. 4 3 2 PIN 1 ID. 1 4 3 2 1 0.270 (6.86) 0.250 (6.35) 5 6 7 0.270 (6.86) 0.250 (6.35) 8 5 6 0.070 (1.78) 0.045 (1.14) 0.020 (0.51) MIN 0.200 (5.08) 0.140 (3.55) 0.154 (3.90) 0.120 (3.05) 0.022 (0.56) 0.016 (0.41) 7 8 0.390 (9.91) 0.370 (9.40) SEATING PLANE SEATING PLANE 0.390 (9.91) 0.370 (9.40) 0.016 (0.40) 0.008 (0.20) 0.100 (2.54) TYP 0.070 (1.78) 0.045 (1.14) 0.004 (0.10) MIN 0.200 (5.08) 0.140 (3.55) 15 MAX 0.154 (3.90) 0.120 (3.05) 0.300 (7.62) TYP 0.022 (0.56) 0.016 (0.41) 0.016 (0.40) 0.008 (0.20) 0.100 (2.54) TYP Surface Mount 0 to 15 0.400 (10.16) TYP 8-Pin DIP - Land Pattern 0.390 (9.91) 0.370 (9.40) 4 3 2 1 0.070 (1.78) PIN 1 ID. 0.060 (1.52) 0.270 (6.86) 0.250 (6.35) 5 6 7 0.100 (2.54) 8 0.295 (7.49) 0.070 (1.78) 0.045 (1.14) 0.020 (0.51) MIN 0.022 (0.56) 0.016 (0.41) 0.100 (2.54) TYP Lead Coplanarity : 0.004 (0.10) MAX 0.415 (10.54) 0.300 (7.62) TYP 0.030 (0.76) 0.016 (0.41) 0.008 (0.20) 0.045 (1.14) 0.315 (8.00) MIN 0.405 (10.30) MAX. Note: All dimensions are in inches (millimeters) (c)2005 Fairchild Semiconductor Corporation 6N137, HCPL2601, HCPL2611, HCPL2630, HCPL2631 Rev. 1.0.7 www.fairchildsemi.com 9 Single-Channel: 6N137, HCPL2601, HCPL2611 Dual-Channel: HCPL2630, HCPL2631 -- High Speed 10MBit/s Logic Gate Optocouplers Package Dimensions Option Example Part Number Description S 6N137S SD 6N137SD W 6N137W 0.4" Lead Spacing V 6N137V VDE0884 WV 6N137WV VDE0884; 0.4" Lead Spacing SV 6N137SV VDE0884; Surface Mount SDV 6N137SDV Surface Mount Lead Bend Surface Mount; Tape and Reel VDE0884; Surface Mount; Tape and Reel Marking Information 1 V 3 2601 2 XX YY T1 6 4 5 Definitions 1 Fairchild logo 2 Device number 3 VDE mark (Note: Only appears on parts ordered with VDE option - See order entry table) 4 Two digit year code, e.g., `03' 5 Two digit work week ranging from `01' to `53' 6 Assembly package code (c)2005 Fairchild Semiconductor Corporation 6N137, HCPL2601, HCPL2611, HCPL2630, HCPL2631 Rev. 1.0.7 www.fairchildsemi.com 10 Single-Channel: 6N137, HCPL2601, HCPL2611 Dual-Channel: HCPL2630, HCPL2631 -- High Speed 10MBit/s Logic Gate Optocouplers Ordering Information 12.0 0.1 4.90 0.20 4.0 0.1 O1.55 0.05 4.0 0.1 0.30 0.05 1.75 0.10 7.5 0.1 13.2 0.2 10.30 0.20 O1.6 0.1 10.30 0.20 0.1 MAX 16.0 0.3 User Direction of Feed Reflow Profile Temperature (C) 300 215 C, 10-30 s 250 225 C peak 200 150 Time above 183C, 60-150 sec 100 50 Ramp up = 3C/sec 0 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 Time (Minute) * Peak reflow temperature: 225C (package surface temperature) * Time of temperature higher than 183C for 60-150 seconds * One time soldering reflow is recommended (c)2005 Fairchild Semiconductor Corporation 6N137, HCPL2601, HCPL2611, HCPL2630, HCPL2631 Rev. 1.0.7 www.fairchildsemi.com 11 Single-Channel: 6N137, HCPL2601, HCPL2611 Dual-Channel: HCPL2630, HCPL2631 -- High Speed 10MBit/s Logic Gate Optocouplers Tape Specifications PDP SPMTM Power-SPMTM PowerTrench(R) Programmable Active DroopTM QFET(R) QSTM Quiet SeriesTM RapidConfigureTM Saving our world, 1mW at a timeTM SmartMaxTM SMART STARTTM SPM(R) STEALTHTM SuperFETTM SuperSOTTM-3 SuperSOTTM-6 SuperSOTTM-8 SupreMOSTM SyncFETTM FPSTM F-PFSTM FRFET(R) SM Global Power Resource Green FPSTM Green FPSTMe-SeriesTM GTOTM IntelliMAXTM ISOPLANARTM MegaBuckTM MICROCOUPLERTM MicroFETTM MicroPakTM MillerDriveTM MotionMaxTM Motion-SPMTM OPTOLOGIC(R) OPTOPLANAR(R) Build it NowTM CorePLUSTM CorePOWERTM CROSSVOLTTM CTLTM Current Transfer LogicTM EcoSPARK(R) EfficentMaxTM EZSWITCHTM * TM (R) Fairchild(R) (R) Fairchild Semiconductor FACT Quiet SeriesTM FACT(R) FAST(R) FastvCoreTM FlashWriter(R) * (R) (R) The Power Franchise TinyBoostTM TinyBuckTM (R) TinyLogic TINYOPTOTM TinyPowerTM TinyPWMTM TinyWireTM SerDesTM UHC(R) Ultra FRFETTM UniFETTM VCXTM VisualMaxTM (R) * EZSWITCHTM and FlashWriter(R) are trademarks of System General Corporation, used under license by Fairchild Semiconductor. DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION, OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. THESE SPECIFICATIONS DO NOT EXPAND THE TERMS OF FAIRCHILD'S WORLDWIDE TERMS AND CONDITIONS, SPECIFICALLY THE WARRANTY THEREIN, WHICH COVERS THESE PRODUCTS. LIFE SUPPORT POLICY FAIRCHILD'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. 2. A critical component in any component of a life support, device, or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. ANTI-COUNTERFEITING POLICY Fairchild Semiconductor Corporation's Anti-Counterfeiting Policy. Fairchild's Anti-Counterfeiting Policy is also stated on our external website, www.fairchildsemi.com, under Sales Support. Counterfeiting of semiconductor parts is a growing problem in the industry. All manufacturers of semiconductor products are experiencing counterfeiting of their parts. Customers who inadvertently purchase counterfeit parts experience many problems such as loss of brand reputation, substandard performance, failed applications, and increased cost of production and manufacturing delays. Fairchild is taking strong measures to protect ourselves and our customers from the proliferation of counterfeit parts. Fairchild strongly encourages customers to purchase Fairchild parts either directly from Fairchild or from Authorized Fairchild Distributors who are listed by country on our web page cited above. Products customers buy either from Fairchild directly or from Authorized Fairchild Distributors are genuine parts, have full traceability, meet Fairchild's quality standards for handling and storage and provide access to Fairchild's full range of up-to-date technical and product information. Fairchild and our Authorized Distributors will stand behind all warranties and will appropriately address any warranty issues that may arise. Fairchild will not provide any warranty coverage or other assistance for parts bought from Unauthorized Sources. Fairchild is committed to combat this global problem and encourage our customers to do their part in stopping this practice by buying direct or from authorized distributors. PRODUCT STATUS DEFINITIONS Definition of Terms Datasheet Identification Product Status Advance Information Formative / In Design Preliminary First Production No Identification Needed Full Production Obsolete Not In Production Definition Datasheet contains the design specifications for product development. Specifications may change in any manner without notice. Datasheet contains preliminary data; supplementary data will be published at a later date. Fairchild Semiconductor reserves the right to make changes at any time without notice to improve design. Datasheet contains final specifications. Fairchild Semiconductor reserves the right to make changes at any time without notice to improve the design. Datasheet contains specifications on a product that is discontinued by Fairchild Semiconductor. The datasheet is for reference information only. Rev. I35 (c)2005 Fairchild Semiconductor Corporation 6N137, HCPL2601, HCPL2611, HCPL2630, HCPL2631 Rev. 1.0.7 www.fairchildsemi.com 12 Single-Channel: 6N137, HCPL2601, HCPL2611 Dual-Channel: HCPL2630, HCPL2631 -- High Speed 10MBit/s Logic Gate Optocouplers TRADEMARKS The following includes registered and unregistered trademarks and service marks, owned by Fairchild Semiconductor and/or its global subsidiaries, and is not intended to be an exhaustive list of all such trademarks.