Aluminum electrolytic capacitors Single-ended capacitors Series/Type: B43866 Date: November 2008 (c) EPCOS AG 2008. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited. Single-ended capacitors B43866 High ripple current 125 C Long-life grade capacitors for professional electronic ballasts Applications Energy-saving lamps Electronic ballasts Power supplies Features High ripple current capability Wide temperature range up to 125 C RoHS-compatible Construction Radial leads Charge-discharge proof, polar Aluminum case with insulating sleeve Minus pole marking on the insulating sleeve Case with safety vent Delivery mode Terminal configurations and packing: Bulk Taped, Ammo pack Cut Kinked PAPR (protection against polarity reversal): crimped leads, J leads, bent leads Refer to chapter "Single-ended capacitors - Taping, packing and lead configurations" for further details and ordering example. Please read Cautions and warnings and Important notes at the end of this document. Page 2 of 27 B43866 High ripple current 125 C Specifications and characteristics in brief Rated voltage VR Surge voltage VS 160 ... 450 V DC 1.1 VR Rated capacitance CR Capacitance tolerance 4.7 ... 150 F 20% M Dissipation factor tan (20 C, 120 Hz) VR 250 V DC: tan (max.) = 0.20 VR 350 V DC: tan (max.) = 0.25 Leakage current Ileak (20 C, 5 min) Self-inductance ESL Useful life 125 C; VR; IAC,R Requirements Voltage endurance test 125 C; VR Post test requirements Vibration resistance test Diameter (mm) 12.5 16 18 ESL (nH) 20 26 34 > 3000 h for d = 10 mm > 5000 h for d 12.5 mm C/C tan Ileak 35% of initial value 3 times initial specified limit initial specified limit 3000 h for d = 10 mm 5000 h for d 12.5 mm C/C 30% of initial value tan 2 times initial specified limit Ileak initial specified limit To IEC 60068-2-6, test Fc: Displacement amplitude 1.5 mm, frequency range 10 ... 2000 Hz, acceleration max. 20 g, duration 3 x 2 h. Capacitor rigidly clamped by the aluminum case. IEC climatic category To IEC 60068-1: VR 250 V: 40/125/56 (40 C/+125 C/56 days damp heat test) VR 350 V: 25/125/56 (25 C/+125 C/56 days damp heat test) Sectional specification IEC 60384-4 Please read Cautions and warnings and Important notes at the end of this document. Page 3 of 27 B43866 High ripple current 125 C Dimensional drawings With stand-off rubber seal Diameters (mm): 10, 12.5, 16, 18 Dimensions and weights Dimensions (mm) d +0.5 10 10 12.5 12.5 12.5 16 16 16 18 18 l 16 +1.0 20 +2.0 20 +2.0 25 +2.0 30 +2.0 20 +2.0 25 +2.0 31.5 +2.0 31.5 +2.0 35 +2.0 Please read Cautions and warnings and Important notes at the end of this document. a 0.5 5.0 5.0 5.0 5.0 5.0 7.5 7.5 7.5 7.5 7.5 Page 4 of 27 b 0.60 0.05 0.60 0.05 0.60 0.05 0.60 0.05 0.80 0.05 0.80 0.05 0.80 0.05 0.80 0.05 0.80 0.1 0.80 0.1 Approx. weight g 1.9 2.6 3.6 4.5 5.3 5.5 7.5 7.8 11.0 13.0 B43866 High ripple current 125 C Overview of available types VR (V DC) 160 250 350 400 450 Case dimensions d x l (mm) CR (F) 10 x 16 10 x 16 10 x 16 10 x 16 10 x 20 x 20 10 4.7 6.8 10 10 x 16 10 x 20 12.5 x 20 15 10 x 20 12.5 x 20 12.5 x 25 12.5 x 25 12.5 x 30 22 10 x 16 12.5 x 20 12.5 x 25 16 x 25 33 10 x 20 12.5 x 25 16 x 25 16 x 25 16 x 31.5 47 12.5 x 20 16 x 20 16 x 31.5 18 x 31.5 18 x 35 68 12.5 x 25 16 x 31.5 18 x 31.5 18 x 31.5 100 16 x 25 150 16 x 31.5 Other voltage and capacitance ratings are available upon request. Please read Cautions and warnings and Important notes at the end of this document. Page 5 of 27 B43866 High ripple current 125 C Technical data and ordering codes CR 120 Hz 20 C F Case dimensions dxl mm VR = 160 V DC 22 10 x 16 33 10 x 20 47 12.5 x 20 68 12.5 x 25 100 16 x 25 150 16 x 31.5 VR = 250 V DC 10 10 x 16 15 10 x 20 22 12.5 x 20 33 12.5 x 25 47 16 x 20 68 16 x 31.5 100 18 x 31.5 VR = 350 V DC 6.8 10 x 16 10 10 x 20 15 12.5 x 20 22 12.5 x 25 33 16 x 25 47 16 x 31.5 68 18 x 31.5 IAC,R 100 kHz 125 C mA IAC,max 100 kHz 105 C mA Ordering code (composition see below) 225 280 300 370 500 650 315 392 420 518 700 910 B43866C1226M*** B43866C1336M*** B43866C1476M*** B43866C1686M*** B43866C1107M*** B43866C1157M*** 125 185 250 280 320 550 600 175 259 350 392 448 770 840 B43866C2106M*** B43866C2156M*** B43866C2226M*** B43866C2336M*** B43866C2476M*** B43866C2686M*** B43866C2107M*** 100 160 200 250 340 365 480 140 224 280 350 476 511 672 B43866C4685M*** B43866C4106M*** B43866C4156M*** B43866C4226M*** B43866C4336M*** B43866C4476M*** B43866C4686M*** Composition of ordering code *** = Version 000 = for standard leads, bulk 001 = for kinked leads, bulk (from d x l = 10 x 20 mm to 18 x 35 mm, excluding 12.5 x 30 mm) 002 = for cut leads, bulk (excluding 12.5 x 30 mm) 003 = for crimped leads, blister (from d x l = 16 x 20 mm to 18 x 35 mm) 004 = for J leads, blister (from d x l = 10 x 16 mm to 18 x 25 mm, excluding 12.5 x 30 mm) 008 = for taped leads, Ammo pack, lead spacing F = 5.0 mm (from d x l = 10 x 16 mm to 12.5 x 25 mm) 009 = for taped leads, Ammo pack, lead spacing F = 7.5 mm (from d x l = 16 x 20 mm to 18 x 31.5 mm) 012 = for bent 90 leads, blister (for 16 and 18 mm) Please read Cautions and warnings and Important notes at the end of this document. Page 6 of 27 B43866 High ripple current 125 C Technical data and ordering codes CR 120 Hz 20 C F Case dimensions dxl mm VR = 400 V DC 4.7 10 x 16 6.8 10 x 16 10 10 x 20 15 12.5 x 25 22 12.5 x 30 33 16 x 25 47 18 x 31.5 VR = 450 V DC 4.7 10 x 16 6.8 10 x 20 10 12.5 x 20 15 12.5 x 25 22 16 x 25 33 16 x 31.5 47 18 x 35 IAC,R 100 kHz 125 C mA IAC,max 100 kHz 105 C mA Ordering code (composition see below) 100 100 160 250 280 340 480 140 140 224 350 392 476 672 B43866C9475M*** B43866C9685M*** B43866C9106M*** B43866C9156M*** B43866C9226M*** B43866C9336M*** B43866C9476M*** 100 160 200 250 300 365 480 140 224 280 350 420 511 672 B43866C5475M*** B43866C5685M*** B43866C5106M*** B43866C5156M*** B43866C5226M*** B43866C5336M*** B43866C5476M*** Composition of ordering code *** = Version 000 = for standard leads, bulk 001 = for kinked leads, bulk (from d x l = 10 x 20 mm to 18 x 35 mm, excluding 12.5 x 30 mm) 002 = for cut leads, bulk (excluding 12.5 x 30 mm) 003 = for crimped leads, blister (from d x l = 16 x 20 mm to 18 x 35 mm) 004 = for J leads, blister (from d x l = 10 x 16 mm to 18 x 25 mm, excluding 12.5 x 30 mm) 008 = for taped leads, Ammo pack, lead spacing F = 5.0 mm (from d x l = 10 x 16 mm to 12.5 x 25 mm) 009 = for taped leads, Ammo pack, lead spacing F = 7.5 mm (from d x l = 16 x 20 mm to 18 x 31.5 mm) 012 = for bent 90 leads, blister (for 16 and 18 mm) Please read Cautions and warnings and Important notes at the end of this document. Page 7 of 27 B43866 High ripple current 125 C Useful life depending on ambient temperature TA under ripple current operating conditions1) d = 10 mm d 12.5 mm 1) Refer to chapter "General technical information, 5.3 Calculation of useful life" for an explanation on how to interpret the useful life graphs. Please read Cautions and warnings and Important notes at the end of this document. Page 8 of 27 B43866 High ripple current 125 C Frequency factor of permissible ripple current IAC versus frequency f Please read Cautions and warnings and Important notes at the end of this document. Page 9 of 27 B43866 High ripple current 125 C Taping, packing and lead configurations Taping Single-ended capacitors are available taped in Ammo pack from diameter 5 to 18 mm as follows: Lead spacing F = 2.5 mm ( d = 5 ... 6.3 mm) Lead spacing F = 3.5 mm ( d = 8 mm) Lead spacing F = 5.0 mm (from d x l = 10 x 12.5 mm to 12.5 x 30 mm) Lead spacing F = 7.5 mm ( d = 16 ... 18 mm). Lead spacing 2.5 mm ( d = 5 ... 6.3 mm) Last 3 digits of ordering code: 007 Dimensions in mm d 5 F H W W0 W1 W2 H0 P P0 P1 I1 t h D0 2.5 18.5 18.0 5.5 9.0 1.5 16.0 12.7 12.7 5.1 1.0 0.7 1.0 4.0 6.3 Toler- +0.8 0.75 0.5 min. 0.5 max. 0.5 1.0 0.2 0.5 max. 0.2 max. 0.2 ance 0.2 Please read Cautions and warnings and Important notes at the end of this document. Page 10 of 27 B43866 High ripple current 125 C Lead spacing 3.5 mm ( d = 8 mm) Last 3 digits of ordering code: 006 Dimensions in mm d 8 Tolerance F H W W0 W1 W2 P P0 P1 I1 t h 3.5 18.5 18.0 12.5 9.0 1.5 12.7 12.7 4.6 1.0 0.7 1.0 +0.8 1.0 0.2 0.5 min. 0.5 max. 1.0 0.2 0.5 max. 0.2 Please read Cautions and warnings and Important notes at the end of this document. Page 11 of 27 D0 4.0 max. 0.2 B43866 High ripple current 125 C Lead spacing 5.0 mm ( d = 5 ... 8 mm) Last 3 digits of ordering code: 008 Lead spacing 5.0 mm (from d x l = 10 x 12.5 mm to 12.5 x 30 mm) Last 3 digits of ordering code: 008 Dimensions in mm d 5 6.3 F H W W0 W1 W2 H0 P P0 P1 I1 t h D0 5.0 18.5 18.0 5.5 9.0 1.5 16.0 12.7 12.7 3.85 1.0 0.7 1.0 4.0 16.0 12.7 12.7 3.85 18.0 12.5 9.0 1.5 12.7 12.7 3.85 1.0 0.7 1.0 4.0 15.0 15.0 5.0 1.0 0.2 0.5 8 10 20.0 5.0 19.0 12.5 19.0 Toler- +0.8 0.75 0.5 min. 0.5 max. 0.5 ance 0.2 Please read Cautions and warnings and Important notes at the end of this document. Page 12 of 27 max. 0.2 max. 0.2 B43866 High ripple current 125 C Lead spacing 7.5 mm ( d = 16 ...18 mm) Last 3 digits of ordering code: 009 Dimensions in mm d 16 F H W 7.5 18.5 18.0 18 *) Toler0.5 0.8 0.5 ance +0.75 W0 W1 W2 P P0 P1 I1 t P h D0 12.5 9.0 1.5 30.0 15.0 3.75 1.0 0.7 0 0 4.0 min. 0.5 max. 1.0 0.2 0.5 max. 0.2 1.0 1.0 0.2 *) Available only for case dimensions 18 x 20, 18 x 25 and 18 x 31.5 mm Please read Cautions and warnings and Important notes at the end of this document. Page 13 of 27 B43866 High ripple current 125 C Packing units and box dimensions Ammo pack Please read Cautions and warnings and Important notes at the end of this document. Case size dxl mm Dimensions (mm) Amax Bmax Cmax 5 x 11 345 55 240 2000 6.3 x 11 345 55 290 2000 8 x 11.5 345 55 240 1000 10 x 12.5 345 55 280 750 10 x 16 345 60 200 500 10 x 20 345 60 200 500 12.5 x 20 345 65 280 500 12.5 x 25 345 65 280 500 16 x 20 315 65 275 300 16 x 25 315 65 275 300 16 x 31.5 315 65 275 300 18 x 20 315 65 275 250 18 x 25 315 65 275 250 18 x 31.5 315 65 275 250 Page 14 of 27 Packing units pcs. B43866 High ripple current 125 C Kinked or cut leads Single-ended capacitors are available with kinked or cut leads. Other lead configurations also available upon request. Kinked leads Last 3 digits of ordering code: 001 With stand-off rubber seal Case size d x l (mm) With flat rubber seal Please read Cautions and warnings and Important notes at the end of this document. Page 15 of 27 Dimensions (mm) a 0.5 10 x 20 5.0 12.5 x 20 5.0 12.5 x 25 5.0 16 x 20 7.5 16 x 25 7.5 16 x 31.5 7.5 18 x 20 7.5 18 x 25 7.5 18 x 31.5 7.5 18 x 35 7.5 18 x 40 7.5 B43866 High ripple current 125 C Cut leads Last 3 digits of ordering code: 002 With stand-off rubber seal Case size d x l (mm) With flat rubber seal Please read Cautions and warnings and Important notes at the end of this document. Page 16 of 27 Dimensions (mm) a 0.5 10 x 12.5 5.0 10 x 16 5.0 10 x 20 5.0 12.5 x 20 5.0 12.5 x 25 5.0 16 x 20 7.5 16 x 25 7.5 16 x 31.5 7.5 18 x 20 7.5 18 x 25 7.5 18 x 31.5 7.5 18 x 35 7.5 18 x 40 7.5 20 x 20 10.0 20 x 25 10.0 20 x 30 10.0 20 x 35 10.0 20 x 40 10.0 22 x 30 10.0 22 x 35 10.0 22 x 40 10.0 B43866 High ripple current 125 C PAPR leads (Protection Against Polarity Reversal) These lead configurations ensure correct placement of the capacitor on the PCB with regard to polarity. PAPR leads are available for diameters from 10 mm up to 20 mm. There are three configurations available: Crimped leads, J leads, bent 90 leads Crimped leads Last 3 digits of ordering code: 003 With stand-off rubber seal With flat rubber seal Suggestion for PCB hole diameter Case size d x l (mm) Dimensions (mm) B 0.2 C 0.5 D 0.1 E 0.1 16 x 20 1.5 3.0 1.3 0.3 7.5 0.8 0.05 16 x 25 1.5 3.0 1.3 0.3 7.5 0.8 0.05 16 x 31.5 1.5 3.0 1.3 0.3 7.5 0.8 0.05 18 x 20 1.5 3.0 1.3 0.3 7.5 0.8 0.1 18 x 25 1.5 3.0 1.3 0.3 7.5 0.8 0.1 18 x 31.5 1.5 3.0 1.3 0.3 7.5 0.8 0.1 18 x 35 1.5 3.0 1.3 0.3 7.5 0.8 0.1 18 x 40 1.5 3.0 1.3 0.3 7.5 0.8 0.1 20 x 20 1.5 3.0 1.6 0.3 10.0 1.0 0.1 20 x 25 1.5 3.0 1.6 0.3 10.0 1.0 0.1 20 x 30 1.5 3.0 1.6 0.3 10.0 1.0 0.1 20 x 35 1.5 3.0 1.6 0.3 10.0 1.0 0.1 20 x 40 1.5 3.0 1.6 0.3 10.0 1.0 0.1 Please read Cautions and warnings and Important notes at the end of this document. Page 17 of 27 a 0.5 b B43866 High ripple current 125 C J leads Last 3 digits of ordering code: 004 Suggestion for PCB hole diameter Case size d x l (mm) Dimensions (mm) C 0.5 E 0.5 J 0.2 10 x 12.5 3.2 0.7 1.2 5.0 0.6 0.05 10 x 16 3.2 0.7 1.2 5.0 0.6 0.05 10 x 20 3.2 0.7 1.2 5.0 0.6 0.05 12.5 x 20 3.2 0.7 1.2 5.0 0.6 0.05 12.5 x 25 3.2 0.7 1.2 5.0 0.6 0.05 16 x 20 3.5 0.7 1.6 7.5 0.8 0.05 16 x 25 3.5 0.7 1.6 7.5 0.8 0.05 16 x 31.5 3.5 0.7 1.6 7.5 0.8 0.05 18 x 20 3.5 0.7 1.6 7.5 0.8 0.1 18 x 25 3.5 0.7 1.6 7.5 0.8 0.1 18 x 31.5 3.5 0.7 1.6 7.5 0.8 0.1 18 x 35 3.5 0.7 1.6 7.5 0.8 0.1 Please read Cautions and warnings and Important notes at the end of this document. Page 18 of 27 a 0.5 b B43866 High ripple current 125 C Bent 90 leads for horizontal mounting pinning Last 3 digits of ordering code: 012 Case size d x l (mm) Dimensions (mm) C 0.5 E 0.5 F 0.5 a 0.5 b 16 x 20 4.0 4.0 12.0 7.5 0.8 0.05 16 x 25 4.0 4.0 12.0 7.5 0.8 0.05 16 x 31.5 4.0 4.0 12.0 7.5 0.8 0.05 18 x 20 4.0 4.0 13.0 7.5 0.8 0.1 18 x 25 4.0 4.0 13.0 7.5 0.8 0.1 18 x 31.5 4.0 4.0 13.0 7.5 0.8 0.1 18 x 35 4.0 4.0 13.0 7.5 0.8 0.1 18 x 40 4.0 4.0 13.0 7.5 0.8 0.1 Bent leads for diameter 12.5 mm available upon request. Please read Cautions and warnings and Important notes at the end of this document. Page 19 of 27 B43866 High ripple current 125 C Overview of packing units and code numbers for case sizes 5 x 11 ... 16 x 31.5 PAPR Case size dxl Taped, Ammo pack mm Standard, bulk pcs. pcs. Kinked leads, bulk pcs. Cut leads, bulk pcs. Crimped J leads, leads, blister blister pcs. pcs. 2000 5 x 11 2000 6.3 x 11 2500 2000 8 x 11.5 1000 1000 10 x 12.5 1000 750 10 x 16 1000 500 1000 10 x 20 500 500 500 500 12.5 x 20 350 500 350 350 12.5 x 25 250 500 500 500 12.5 x 30 200 12.5 x 35 175 12.5 x 40 175 16 x 20 250 300 200 200 200 200 120 16 x 25 250 300 200 200 200 200 120 16 x 31.5 200 300 250 250 344 344 120 The last three digits of the complete ordering code state the lead configuration 000 Code 006 007 008 009 001 002 003 004 012 F (mm) d (mm) 3.5 2.5 5 7.5 8 5...6.3 5...12.5 16...18 1) Available upon request Please read Cautions and warnings and Important notes at the end of this document. Page 20 of 27 1000 Bent 90 leads, blister pcs. 675 675 500 300 1) 225 1) B43866 High ripple current 125 C Overview of packing units and code numbers for case sizes 18 x 20 ... 25 x 40 PAPR Case size dxl Taped, Ammo pack mm Standard, bulk pcs. pcs. Kinked leads, bulk pcs. Cut leads, bulk pcs. Crimped J leads, leads, blister blister pcs. pcs. Bent 90 leads, blister pcs. 18 x 20 175 18 x 25 150 250 175 175 200 200 120 250 150 150 200 200 18 x 31.5 120 100 250 100 100 150 150 120 18 x 35 100 100 100 150 150 150 18 x 40 125 100 100 120 72 20 x 20 125 125 200 20 x 25 125 125 200 20 x 30 100 100 120 20 x 35 100 100 120 20 x 40 100 100 120 22 x 30 80 100 22 x 35 80 22 x 40 80 25 x 40 40 The last three digits of the complete ordering code state the lead configuration 000 Code 007 008 009 Please read Cautions and warnings and Important notes at the end of this document. F (mm) d (mm) 2.5 5 7.5 100 100 001 002 4...6.3 6.3...12.5 16...18 Page 21 of 27 003 004 012 B43866 High ripple current 125 C Cautions and warnings Personal safety The electrolytes used by EPCOS have not only been optimized with a view to the intended application, but also with regard to health and environmental compatibility. They do not contain any solvents that are detrimental to health, e.g. dimethyl formamide (DMF) or dimethyl acetamide (DMAC). Furthermore, part of the high-voltage electrolytes used by EPCOS are self-extinguishing. They contain flame-retarding substances which will quickly extinguish any flame that may have been ignited. As far as possible, EPCOS does not use any dangerous chemicals or compounds to produce operating electrolytes. However, in exceptional cases, such materials must be used in order to achieve specific physical and electrical properties because no safe substitute materials are currently known. However, the amount of dangerous materials used in our products has been limited to an absolute minimum. Nevertheless, the following rules should be observed when handling Al electrolytic capacitors: Any escaping electrolyte should not come into contact with eyes or skin. If electrolyte does come into contact with the skin, wash the affected parts immediately with running water. If the eyes are affected, rinse them for 10 minutes with plenty of water. If symptoms persist, seek medical treatment. Avoid breathing in electrolyte vapor or mists. Workplaces and other affected areas should be well ventilated. Clothing that has been contaminated by electrolyte must be changed and rinsed in water. Please read Cautions and warnings and Important notes at the end of this document. Page 22 of 27 B43866 High ripple current 125 C Product safety The table below summarize the safety instructions that must be observed without fail. A detailed description can be found in the relevant sections of chapter "General technical information". Topic Safety information Polarity Make sure that polar capacitors are connected with the right polarity. Reverse voltage Voltages polarity classes should be prevented by connecting a diode. Do not exceed the upper category temperatur. Upper category temperature Maintenance Mounting position of screw terminal capacitors Mounting of single-ended capacitors Robustness of terminals Soldering Make periodic inspections of the capacitors. Before the inspection, make sure that the power supply is turned off and carefully discharge the electricity of the capacitors. Do not apply any mechanical stress to the capacitor terminals. Do not mount the capacitor with the terminals (safety vent) upside down. Reference Chapter "General technical information" 1 "Basic construction of aluminum electrolytic capacitors" 3.1.6 "Reverse voltage" 7.2 "Maximum permissible operating temperature" 10 "Maintenance" 11.1 "Mounting positions of capacitors with screw terminals" The internal structure of single-ended capacitors 11.4 might be damaged if excessive force is applied to "Mounting the lead wires. considerations for Avoid any compressive, tensile or flexural stress. single-ended capacitors" Do not move the capacitor after soldering to PC board. Do not pick up the PC board by the soldered capacitor. Do not insert the capacitor on the PC board with a hole space different to the lead space specified. The following maximum tightening torques must 11.3 not be exceeded when connecting screw "Mounting torques" terminals: M5: 2 Nm M6: 2.5 Nm Do not exceed the specified time or temperature 11.5 limits during soldering. "Soldering" Please read Cautions and warnings and Important notes at the end of this document. Page 23 of 27 B43866 High ripple current 125 C Topic Soldering, cleaning agents Passive flammability Active flammability Safety information Reference Chapter "General technical information" Do not allow halogenated hydrocarbons to come 11.6 into contact with aluminum electrolytic capacitors. "Cleaning agents" Avoid external energy, such as fire or electricity. 8.1 "Passive flammability" Avoid overload of the capacitors. 8.2 "Active flammability" Breakdown strength Do not damage the insulating sleeve, especially of insulating when ring clips are used for mounting. sleeves Please read Cautions and warnings and Important notes at the end of this document. Page 24 of 27 Reference Chapter "Capacitors with screw terminals" "Screw terminals accessories" B43866 High ripple current 125 C Symbols and terms Symbol English German C CR CS CS,T Cf d dmax ESL ESR ESRf Capacitance Rated capacitance Series capacitance Series capacitance at temperature T Capacitance at frequency f Case diameter, nominal dimension Maximum case diameter Self-inductance Equivalent series resistance Equivalent series resistance at frequency f Equivalent series resistance at temperature T Frequency Current Alternating current (ripple current) Root-mean-square value of alternating current Ripple current at frequency f Maximum permissible ripple current Rated ripple current Rated ripple current for base cooling Leakage current Operating leakage current Case length, nominal dimension Maximum case length (without terminals and mounting stud) Resistance Insulation resistance Balancing resistance Temperature Temperature difference Ambient temperature Case temperature Capacitor base temperature Time Period Service life (operating hours) Kapazitat Nennkapazitat Serienkapazitat Serienkapazitat bei Temperatur T Kapazitat bei Frequenz f Gehausedurchmesser, Nennma Maximaler Gehausedurchmesser Eigeninduktivitat Ersatzserienwiderstand Ersatzserienwiderstand bei Frequenz f ESRT f I IAC IAC,rms IAC,f IAC,max IAC,R IAC,R (B) Ileak Ileak,op l lmax R Rins Rsymm T T TA TC TB t t tb Please read Cautions and warnings and Important notes at the end of this document. Ersatzserienwiderstand bei Temperatur T Frequenz Strom Wechselstrom Wechselstrom, Effektivwert Wechselstrom bei Frequenz f Maximal zulassiger Wechselstrom Nennwechselstrom Nennwechselstromstrom fur Bodenkuhlung Ableitstrom Ableitstrom bei Betrieb Gehauselange, Nennma Maximale Gehauselange (ohne Anschlusse und Gewindebolzen) Widerstand Isolationswiderstand Symmetrierwiderstand Temperatur Temperaturdifferenz Umgebungstemperatur Gehausetemperatur Temperatur des Becherbodens Zeit Zeitraum Brauchbarkeitsdauer (Betriebszeit) Page 25 of 27 B43866 High ripple current 125 C Symbol V VF Vop VR VS XC XL Z ZT tan 0 r English Voltage Forming voltage Operating voltage Rated voltage, DC voltage Surge voltage Capacitive reactance Inductive reactance Impedance Impedance at temperature T Dissipation factor Failure rate Absolute permittivity Relative permittivity Angular velocity; 2 f German Spannung Formierspannung Betriebsspannung Nennspannung, Gleichspannung Spitzenspannung Kapazitiver Blindwiderstand Induktiver Blindwiderstand Scheinwiderstand Scheinwiderstand bei Temperatur T Verlustfaktor Ausfallrate Elektrische Feldkonstante Dielektrizitatszahl Kreisfrequenz; 2 f Notes All dimensions are given in mm. Please read Cautions and warnings and Important notes at the end of this document. Page 26 of 27 Important notes The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether an EPCOS product with the properties described in the product specification is suitable for use in a particular customer application. 2. We also point out that in individual cases, a malfunction of electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified. In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health (e.g. in accident prevention or lifesaving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of an electronic component. 3. The warnings, cautions and product-specific notes must be observed. 4. In order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as hazardous). Useful information on this will be found in our Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more detailed questions, please contact our sales offices. 5. We constantly strive to improve our products. Consequently, the products described in this publication may change from time to time. The same is true of the corresponding product specifications. Please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products. Consequently, we cannot guarantee that all products named in this publication will always be available. The aforementioned does not apply in the case of individual agreements deviating from the foregoing for customer-specific products. 6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the "General Terms of Delivery for Products and Services in the Electrical Industry" published by the German Electrical and Electronics Industry Association (ZVEI). 7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CSSP, CTVS, DSSP, MiniBlue, MKK, MLSC, MotorCap, PCC, PhaseCap, PhaseMod, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMDAD, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are trademarks registered or pending in Europe and in other countries. Further information will be found on the Internet at www.epcos.com/trademarks. Page 27 of 27