NLX2G08 Dual 2-Input AND Gate The NLX2G08 is an advanced high-speed dual 2-input CMOS AND gate in ultra-small footprint. The NLX2G08 input structures provide protection when voltages up to 7.0 volts are applied, regardless of the supply voltage. http://onsemi.com Features * * * * * * * High Speed: tPD 2.5 ns (typical) at VCC = 5.0 V Designed for 1.65 V to 5.5 V VCC Operation Low Power Dissipation: ICC = 1 mA (Max) at TA = 25C 24 mA Balanced Output Sink and Source Capability Balanced Propagation Delays Overvoltage Tolerant (OVT) Input Pins This is a Pb-Free Device A1 7 B1 6 A1 Y2 5 1 1 B1 VCC MARKING DIAGRAMS 8 2 7 1 Y1 2 B2 3 A2 1 XXM G 1 ULLGA8 1.6 x 1.0 CASE 613AB XXM G ULLGA8 1.95 x 1.0 CASE 613AC XXM G Y1 1 Y2 3 GND 6 4 5 B2 IEEE/IEC & Y1 A2 B2 PIN ASSIGNMENT Figure 2. Logic Symbol Y = AB Inputs Output 1 UDFN8 1.6 x 1.0 CASE 517BY 1 UDFN8 1.95 x 1.0 CASE 517CA Y2 FUNCTION TABLE UDFN8 1.45 x 1.0 CASE 517BZ Pin Function (UQFN8) Function (ULLGA) 1 Y1 A1 XM A2 Figure 1. Pinouts A1 B1 AD MG G ULLGA8 1.45 x 1.0 CASE 613AA VCC GND 4 8 8 1 UQFN8 MU SUFFIX CASE 523AN XX M G XM XM 1 = Specific Device Code = Date Code = Pb-Free Package (Note: Microdot may be in either location) 2 B2 B1 A B Y 3 A2 Y2 L L H ORDERING INFORMATION 4 GND GND L H H See detailed ordering and shipping information in the package dimensions section on page 4 of this data sheet. 5 Y2 A2 H L H 6 B1 B2 H H L 7 A1 Y1 8 VCC VCC H = HIGH Logic Level L = LOW Logic Level (c) Semiconductor Components Industries, LLC, 2012 July, 2012 - Rev. 2 1 Publication Order Number: NLX2G08/D NLX2G08 MAXIMUM RATINGS Symbol Value Unit VCC DC Supply Voltage *0.5 to +7.0 V VIN DC Input Voltage *0.5 to +7.0 V *0.5 to VCC + 0.5 V VIN < GND *50 mA VOUT < GND *50 mA VOUT Parameter DC Output Voltage IIK DC Input Diode Current IOK DC Output Diode Current IO DC Output Source/Sink Current $50 mA ICC DC Supply Current per Supply Pin $100 mA IGND DC Ground Current per Ground Pin $100 mA TSTG Storage Temperature Range *65 to )150 C TL Lead Temperature, 1 mm from Case for 10 Seconds TBD C TJ Junction Temperature Under Bias TBD C qJA Thermal Resistance (Note 1) TBD C/W PD Power Dissipation in Still Air at 85C TBD mW MSL Moisture Sensitivity FR Flammability Rating VESD ILatchup Level 1 Oxygen Index: 28 to 34 ESD Withstand Voltage UL 94 V-0 @ 0.125 in Human Body Model (Note 2) Machine Model (Note 3) Charged Device Model (Note 4) Latchup Performance Above VCC and Below GND at 125C (Note 5) TBD TBD N/A V $500 mA Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. Measured with minimum pad spacing on an FR4 board, using 10 mm-by-1 inch, 2-ounce copper trace with no air flow. 2. Tested to EIA/JESD22-A114-A. 3. Tested to EIA/JESD22-A115-A. 4. Tested to JESD22-C101-A. 5. Tested to EIA/JESD78. RECOMMENDED OPERATING CONDITIONS Symbol Parameter Max Unit 1.65 1.5 5.5 5.5 V VCC Power DC Supply Voltage VIN Digital Input Voltage (Note 6) 0 5.5 V Output Voltage 0 VCC V -55 +125 C 0 0 0 0 20 20 10 5 ns/V VOUT TA Operating Free-Air Temperature Dt/DV Input Transition Rise or Fall Rate Operating Data Retention Only Min VCC = 1.8 V $0.15 V VCC = 2.5 V $0.2 V VCC = 3.3 V $0.3 V VCC = 5.0 V $0.5 V 6. Unused inputs may not be left open. All inputs must be tied to a high- or low-logic input voltage level. http://onsemi.com 2 NLX2G08 DC ELECTRICAL CHARACTERISTICS Symbol Parameter VIH High-Level Input Voltage VIL VOH Condition 1.65 2.3 to 5.5 Low-Level Input Voltage High-Level Output Voltage Low-Level Output Voltage Min Typ VIN = VIH or VIL, IOH = -100 mA VIN = VIH or VIL, IOL = 100 mA Max Min Max 0.75 x VCC 0.7 x VCC 0.25 x VCC 0.3 x VCC 2.3 to 5.5 TA = -555C to +1255C TA 3 855C 0.75 x VCC 0.7 x VCC 1.65 VIN = VIH or VIL IOH = -4 mA IOH = -8 mA IOH = -12 mA IOH = -16 mA IOH = -24 mA IOH = -32 mA VOL VCC (V) TA = 255C Min 0.75 x VCC 0.7 x VCC 0.25 x VCC 0.3 x VCC VCC - 0.1 VCC VCC - 0.1 VCC - 0.1 1.65 2.3 2.7 3.0 3.0 4.5 1.29 1.9 2.2 2.4 2.3 3.8 1.5 2.1 2.4 2.7 2.5 4.0 1.29 1.9 2.2 2.4 2.3 3.8 1.29 1.9 2.2 2.4 2.3 3.8 Unit V 0.25 x VCC 0.3 x VCC 1.65 to 5.5 1.65 to 5.5 Max V V 0.1 0.1 0.1 0.24 0.3 0.4 0.4 0.55 0.55 0.24 0.3 0.4 0.4 0.55 0.55 0.24 0.3 0.4 0.4 0.55 0.55 V VIN = VIH or VIL IOL = 4 mA IOL = 8 mA IOL = 12 mA IOL = 16 mA IOL = 24 mA IOL = 32 mA 1.65 2.3 2.7 3.0 3.0 4.5 Input Leakage Current 0 VIN 5.5 V 0 to 5.5 $0.1 $1.0 $1.0 mA IOFF Power-Off Input Leakage Current VIN = 5.5 V 0 1.0 10 10 mA ICC Quiescent Supply Current 0 VIN 5.5 V 5.5 1.0 10 10 mA IIN 0.08 0.20 0.22 0.28 0.38 0.42 AC ELECTRICAL CHARACTERISTICS tR = tF = 2.5 ns TA = 255C VCC Symbol tPLH tPHL Parameter Propagation Delay Input A to Output TA 3 855C TA = -555C to +1255C (V) Test Condition Min Typ Max Min Max Min Max Unit 1.65 to 1.95 RL = 1 MW, CL = 15 pF 2.0 5.7 10.5 2.0 11.0 TBD TBD ns 2.3 to 2.7 RL = 1 MW, CL = 15 pF 1.2 3.5 5.8 2.0 6.2 TBD TBD 3.0 to 3.6 RL = 1 MW, CL = 15 pF 0.8 2.6 3.9 0.8 4.3 TBD TBD RL = 500 W, CL = 50 pF 1.2 3.2 4.8 1.2 5.2 TBD TBD RL = 1 MW, CL = 15 pF 0.5 1.9 3.1 0.5 3.3 TBD TBD RL = 500 W, CL = 50 pF 0.8 2.5 3.7 0.8 4.0 TBD TBD 4.5 to 5.5 CIN Input Capacitance 5.5 VIN = 0 V or VCC 2.5 pF CPD Power Dissipation Capacitance (Note 7) 3.3 5.5 10 MHz, VIN = 0V or VCC 9 11 pF 7. CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption without load. Average operating current can be obtained by the equation: ICC(OPR) = CPD VCC fin + ICC. CPD is used to determine the no-load dynamic power consumption; PD = CPD VCC2 fin + ICC VCC. http://onsemi.com 3 NLX2G08 VCC A and B VCC 50% 50% GND tPLH Y tPHL RL CL 50% VCC A 1-MHz square input wave is recommended for propagation delay tests. PROPAGATION DELAYS tR = tF = 2.5 ns, 10% to 90%; f = 1 MHz; tW = 500 ns Figure 3. Switching Waveform Figure 4. Test Circuit ORDERING INFORMATION Package Shipping UQFN8 (Pb-Free) 3000 / Tape & Reel NLX2G08AMX1TCG ULLGA8, 1.95 x 1.0, 0.5P (Pb-Free) 3000 / Tape & Reel NLX2G08BMX1TCG ULLGA8, 1.6 x 1.0, 0.4P (Pb-Free) 3000 / Tape & Reel NLX2G08CMX1TCG ULLGA8, 1.45 x 1.0, 0.35P (Pb-Free) 3000 / Tape & Reel NLX2G08DMUTCG UDFN8, 1.95 x 1.0, 0.5P (Pb-Free) 3000 / Tape & Reel NLX2G08EMUTCG UDFN8, 1.6 x 1.0, 0.4P (Pb-Free) 3000 / Tape & Reel NLX2G08FMUTCG UDFN8, 1.45 x 1.0, 0.35P (Pb-Free) 3000 / Tape & Reel Device NLX2G08MUTCG For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 4 NLX2G08 PACKAGE DIMENSIONS UDFN8 1.6x1.0, 0.4P CASE 517BY ISSUE O PIN ONE REFERENCE 2X 0.10 C 2X EEE EEE 0.10 C NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.20 MM FROM TERMINAL TIP. 4. PACKAGE DIMENSIONS EXCLUSIVE OF BURRS AND MOLD FLASH. A B D E DIM A A1 A3 b D E e L L1 TOP VIEW A3 0.05 C A 0.05 C A1 SIDE VIEW C RECOMMENDED SOLDERING FOOTPRINT* SEATING PLANE 7X e/2 0.49 e 1 7X MILLIMETERS MIN MAX 0.45 0.55 0.00 0.05 0.13 REF 0.15 0.25 1.60 BSC 1.00 BSC 0.40 BSC 0.25 0.35 0.30 0.40 L 8X 0.26 4 L1 1.24 8 5 BOTTOM VIEW 8X b 0.10 M C A B 0.05 M C 0.53 NOTE 3 0.40 PITCH DIMENSIONS: MILLIMETERS *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 5 1 PKG OUTLINE NLX2G08 PACKAGE DIMENSIONS UDFN8 1.45x1.0, 0.35P CASE 517BZ ISSUE O PIN ONE REFERENCE 2X 0.10 C 2X 0.10 C NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.20 MM FROM TERMINAL TIP. 4. PACKAGE DIMENSIONS EXCLUSIVE OF BURRS AND MOLD FLASH. A B D EE EE E DIM A A1 A3 b D E e L L1 TOP VIEW A3 0.05 C A 0.05 C A1 SIDE VIEW C RECOMMENDED SOLDERING FOOTPRINT* SEATING PLANE 7X 0.48 e/2 e 1 7X MILLIMETERS MIN MAX 0.45 0.55 0.00 0.05 0.13 REF 0.15 0.25 1.45 BSC 1.00 BSC 0.35 BSC 0.25 0.35 0.30 0.40 L 8X 0.22 4 L1 1.18 8 5 BOTTOM VIEW 8X 0.53 b 0.10 M C A B 0.05 M C NOTE 3 0.35 PITCH DIMENSIONS: MILLIMETERS *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 6 1 PKG OUTLINE NLX2G08 PACKAGE DIMENSIONS UDFN8 1.95x1.0, 0.5P CASE 517CA ISSUE O PIN ONE REFERENCE 2X 0.10 C 2X EEE EEE 0.10 C NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.20 MM FROM TERMINAL TIP. 4. PACKAGE DIMENSIONS EXCLUSIVE OF BURRS AND MOLD FLASH. A B D E DIM A A1 A3 b D E e L L1 TOP VIEW A3 0.05 C A 0.05 C A1 SIDE VIEW C RECOMMENDED SOLDERING FOOTPRINT* SEATING PLANE 7X e/2 0.49 e 7X MILLIMETERS MIN MAX 0.45 0.55 0.00 0.05 0.13 REF 0.15 0.25 1.95 BSC 1.00 BSC 0.50 BSC 0.25 0.35 0.30 0.40 L 8X 0.30 4 1 L1 1.24 8 5 BOTTOM VIEW 8X b 0.10 M C A B 0.05 M C 0.54 NOTE 3 0.50 PITCH DIMENSIONS: MILLIMETERS *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 7 1 PKG OUTLINE NLX2G08 PACKAGE DIMENSIONS UQFN8 MU SUFFIX CASE 523AN ISSUE O A B D PIN ONE REFERENCE 2X 0.10 C EEE EEE CCC CCC EEE EEE MOLD CMPD EXPOSED Cu E A1 A3 NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.30 mm FROM THE TERMINAL TIP. DETAIL B DIM A A1 A3 b D E e L L1 L3 OPTIONAL CONSTRUCTION 2X 0.10 C TOP VIEW L1 (A3) DETAIL B L3 A 0.05 C b 0.05 C SIDE VIEW (0.10) C A1 SEATING PLANE MILLIMETERS MIN MAX 0.45 0.60 0.00 0.05 0.13 REF 0.15 0.25 1.60 BSC 1.60 BSC 0.50 BSC 0.35 0.45 --- 0.15 0.25 0.35 (0.15) SOLDERING FOOTPRINT* DETAIL A OPTIONAL CONSTRUCTION 1.70 0.50 PITCH 8X 8X L3 L 1 e 5 3 0.35 1 DETAIL A 1.70 7 8 8X b 0.10 C A B BOTTOM VIEW 0.05 C 7X 0.25 8X 0.53 NOTE 3 DIMENSIONS: MILLIMETERS *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 8 NLX2G08 PACKAGE DIMENSIONS ULLGA8 1.45x1.0, 0.35P CASE 613AA ISSUE A EEE EEE EEE PIN ONE REFERENCE 0.10 C NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.30 mm FROM THE TERMINAL TIP. 4. A MAXIMUM OF 0.05 PULL BACK OF THE PLATED TERMINAL FROM THE EDGE OF THE PACKAGE IS ALLOWED. A B D E DIM A A1 b D E e L L1 TOP VIEW 0.10 C 0.05 C A 8X 0.05 C SEATING PLANE SIDE VIEW MOUNTING FOOTPRINT SOLDERMASK DEFINED* C A1 MILLIMETERS MIN MAX --- 0.40 0.00 0.05 0.15 0.25 1.45 BSC 1.00 BSC 0.35 BSC 0.25 0.35 0.30 0.40 7X 0.48 8X 0.22 e/2 e 1 7X L NOTE 4 4 1.18 L1 0.53 8 5 8X b 0.05 C PKG OUTLINE 0.35 PITCH DIMENSIONS: MILLIMETERS 0.10 C A B BOTTOM VIEW 1 *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. NOTE 3 http://onsemi.com 9 NLX2G08 PACKAGE DIMENSIONS ULLGA8 1.6x1.0, 0.4P CASE 613AB ISSUE A PIN ONE REFERENCE 0.10 C 0.10 C NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.30 mm FROM THE TERMINAL TIP. 4. A MAXIMUM OF 0.05 PULL BACK OF THE PLATED TERMINAL FROM THE EDGE OF THE PACKAGE IS ALLOWED. A B D EEE EEE EEE E DIM A A1 b D E e L L1 TOP VIEW 0.05 C A 8X 0.05 C SEATING PLANE SIDE VIEW MOUNTING FOOTPRINT SOLDERMASK DEFINED* C A1 MILLIMETERS MIN MAX --- 0.40 0.00 0.05 0.15 0.25 1.60 BSC 1.00 BSC 0.40 BSC 0.25 0.35 0.30 0.40 7X 0.49 e/2 e 1 4 8 5 7X L NOTE 4 1.24 L1 0.53 8X b 0.05 C 1 PKG OUTLINE 0.40 PITCH DIMENSIONS: MILLIMETERS 0.10 C A B BOTTOM VIEW 8X 0.26 *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. NOTE 3 http://onsemi.com 10 NLX2G08 PACKAGE DIMENSIONS ULLGA8 1.95x1.0, 0.5P CASE 613AC ISSUE A PIN ONE REFERENCE 0.10 C NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.30 mm FROM THE TERMINAL TIP. 4. A MAXIMUM OF 0.05 PULL BACK OF THE PLATED TERMINAL FROM THE EDGE OF THE PACKAGE IS ALLOWED. A B D EEEE EEEE EEEE E DIM A A1 b D E e L L1 TOP VIEW 0.10 C 0.05 C MILLIMETERS MIN MAX --- 0.40 0.00 0.05 0.15 0.25 1.95 BSC 1.00 BSC 0.50 BSC 0.25 0.35 0.30 0.40 A 8X 0.05 C MOUNTING FOOTPRINT SOLDERMASK DEFINED* SEATING PLANE SIDE VIEW 7X C A1 0.49 8X 0.30 e/2 e 7X L NOTE 4 4 1 1.24 L1 0.53 8 5 8X BOTTOM VIEW b 0.10 C A B 0.05 C 1 PKG OUTLINE 0.50 PITCH DIMENSIONS: MILLIMETERS *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. NOTE 3 ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC's product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5817-1050 http://onsemi.com 11 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NLX2G08/D