CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS TM NPCAP Surface Mount PMA - Series The new construction provides a low profile and high CV. Super low ESR, impedance, and high heat resistance characteristics have been secured by using highly conductive polymer electrolytic materials. Compatible with digitalization and high frequencies of electrical equipment with superior noise absorption. Excellent ESR characteristics, high ripple current, 5,000 hours at 105C. Low-profile product lineup Outer coating: Flame-retardant epoxy resin UL94 V-0 or equivalent Non-solvent resistant type RoHS2 Compliant Halogen free products This product can't be used for applications related to human life (such as in-vehicle equipment). SPECIFICATIONS Items Characteristics Category Temperature Range Rated Voltage Range Capacitance Tolerance Surge Voltage Leakage Current Dissipation Factor (tan) Low Temperature Characteristics (Max. Impedance Ratio) Endurance Damp Heat (Steady State) Surge Voltage Failure Rate -55 to +105 16 to 25Vdc 20% (M) Rated voltagex1.15 Shall not exceed values shown in STANDARD RATINGS. (at 20, 120Hz) (at 105) (at 20 after 2 minutes) 0.12 max. (at 20, 120Hz) Z(-25)/Z(+20)1.15 Z(-55)/Z(+20)1.25 (at 100kHz) The following specifications shall be satisfied when the capacitors are restored to 20 after the rated voltage is applied for 5,000 hours at 105. Appearance No significant damage Capacitance change 20% of the initial value D.F. (tan) 200% of the initial specified value ESR 200% of the initial specified value Leakage current The initial specified value The following specifications shall be satisfied when the capacitors are restored to 20 after exposing them for 500 hours at 60, 90 to 95% RH without voltage applied. Appearance No significant damage Capacitance change -20 to +40% of the initial value D.F. (tan) 200% of the initial specified value ESR 200% of the initial specified value Leakage current The initial specified value The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105 for 30 seconds through a protective resistor(R=1k) and discharge for 5 minutes 30 seconds. Appearance No significant damage Capacitance change 20% of the initial value D.F. (tan) 200% of the initial specified value ESR 200% of the initial specified value Leakage current The initial specified value 0.5% per 1,000 hours maximum (Confidence level 60% at 105) *Note : If any doubt arises, measure the leakage current after the following voltage treatment. Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105. MARKING DIMENSIONS [mm] P EX25V22F A358 E220 W A L B C Size code A B C L W P F30 7.00.1 7.00.1 7.20.2 3.0 max. 1.20.2 2.650.2 Rated voltage symbol Rated voltageVdc Symbol 16 C 20 D 25 E Capacitance symbol Capacitance codeex. 22F220 Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications. CAT. No. E1001S Ver.3 CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS TM NPCAP Surface Mount PMASeries - PART NUMBERING SYSTEM 1 2 3 4 A PMA 5 6 7 8 9 10 A RA 11 12 13 14 15 16 17 18 M F30 S Supplement code Size code Capacitance tolerance code Capacitance code (ex. 22F:220, 39F:390) Taping code Terminal code Voltage code (ex. 20V:200, 25V:250) Series code Category Please refer to "Product code guide (conductive polymer type)" STANDARD RATINGS WV (Vdc) 16 20 25 Cap (F) Size code Leakage current (A max./after 2min.) 56 68 39 47 22 33 F30 F30 F30 F30 F30 F30 448 544 390 470 275 412 ESR Rated ripple current (m max./20, 100k to 300kHz) (mArms/105, 100kHz) 40 50 45 50 50 50 2,200 2,000 2,100 2,000 2,000 2,000 Part No. APMA160ARA560MF30S APMA160ARA680MF30S APMA200ARA390MF30S APMA200ARA470MF30S APMA250ARA220MF30S APMA250ARA330MF30S RATED RIPPLE CURRENT MULTIPLIERS Frequency Multipliers Frequency(Hz) SMD type 120 0.05 1k 0.30 10k 0.55 50k 0.70 100k to 500k 1.00 Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications. CAT. No. E1001S Ver.2