SMSC LAN9513/LAN9513i Revision 1.2 (02-29-12)
PRODUCT PREVIEW
Data Brief
PRODUCT FEATURES
LAN9513/LAN9513i
USB 2.0 Hub and 10/100
Ethernet Controller
Highlights
Three downstream ports, one upstream port
Three integrated downstream USB 2.0 PHYs
One integrated upstream USB 2.0 PHY
Integrated 10/100 Ethernet MAC with full-duplex
support
Integrated 10/100 Ethernet PHY with HP Auto-MDIX
Implements Reduced Power Operating Modes
Minimized BOM Cost
Single 25 MHz crystal (Eliminates cost of separate
crystals for USB and Ethernet)
Built-in Power-On-Reset (POR) circuit (Eliminates
requirement for external passive or active reset)
Target Applications
Desktop PCs
Notebook PCs
Printers
Game Consoles
Embedded Systems
Docking Stations
Key Features
USB Hub
Fully compliant with Universal Serial Bus Specification
Revision 2.0
HS (480 Mbps), FS (12 Mbps), and LS (1.5 Mbps)
compatible
Three downstream ports, one upstream port
Port mapping and disable support
Port Swap: Programmable USB diff-pair pin location
PHY Boost: Programmable USB signal drive strength
Select presence of a permanently hardwired USB
peripheral device on a port by port basis
Advanced power saving features
Downstream PHY goes into low power mode when port
power to the port is disabled
Full Power Management with individual or ganged
power control of each downstream port.
Integrated USB termination Pull-up/Pull-down resistors
Internal short circuit protection of USB differential signal
pins
High-Performance 10/100 Ethernet Controller
Fully compliant with IEEE802.3/802.3u
Integrated Ethernet MAC and PHY
10BASE-T and 100BASE-TX support
Full- and half-duplex support with flow control
Preamble generation and removal
Automatic 32-bit CRC generation and checking
Automatic payload padding and pad removal
Loop-back modes
TCP/UDP checksum offload support
Flexible address filtering modes
One 48-bit perfect address
64 hash-filtered multicast addresses
Pass all multicast
Promiscuous mode
Inverse filtering
Pass all incoming with status report
Wakeup packet support
Integrated Ethernet PHY
Auto-negotiation, HP Auto-MDIX
Automatic polarity detection and correction
Energy Detect
Power and I/Os
Three PHY LEDs
Eight GPIOs
Supports bus-powered and self-powered operation
Internal 1.8v core supply regulator
External 3.3v I/O supply
Miscellaneous features
Optional EEPROM
Optional 24MHz reference clock output for partner hub
IEEE 1149.1 (JTAG) Boundary Scan
Software
Windows 2000/XP/Vista Driver
Linux Driver
Win CE Driver
—MAC OS Driver
EEPROM Utility
Packaging
64-pin QFN, lead-free RoHS compliant
Environmental
Commercial Temperature Range (0°C to +70°C)
Industrial Temperature Range (-40°C to +85°C)
±8kV HBM without External Protection Devices
±8kV contact mode (IEC61000-4-2)
±15kV air-gap discharge mode (IEC61000-4-2)
Order Numbers:
LAN9513-JZX for 64-pin, QFN lead-free RoHS compliant package (0 to +70°C temp range)
LAN9513i-JZX for 64-pin, QFN lead-free RoHS compliant package (-40 to +85°C temp range)
This product meets the halogen maximum concentration values per IEC61249-2-21
For RoHS compliance and environmental information, please visit www.smsc.com/rohs
USB 2.0 Hub and 10/100 Ethernet Controller
Revision 1.2 (02-29-12) 2 SMSC LAN9513/LAN9513i
PRODUCT PREVIEW
Copyright © 2012 SMSC or its subsidiaries. All rights reserved.
Circuit diagrams and other information relating to SMSC products are included as a means of illustrating typical applications. Consequently, complete information sufficient for
construction purposes is not necessarily given. Although the information has been checked and is believed to be accurate, no responsibility is assumed for inaccuracies. SMSC
reserves the right to make changes to specifications and product descriptions at any time without notice. Contact your local SMSC sales office to obtain the latest specifications
before placing your product order. The provision of this information does not convey to the purchaser of the described semiconductor devices any licenses under any patent
rights or other intellectual property rights of SMSC or others. All sales are expressly conditional on your agreement to the terms and conditions of the most recently dated
version of SMSC's standard Terms of Sale Agreement dated before the date of your order (the "Terms of Sale Agreement"). The product may contain design defects or errors
known as anomalies which may cause the product's functions to deviate from published specifications. Anomaly sheets are available upon request. SMSC products are not
designed, intended, authorized or warranted for use in any life support or other application where product failure could cause or contribute to personal injury or severe property
damage. Any and all such uses without prior written approval of an Officer of SMSC and further testing and/or modification will be fully at the risk of the customer. Copies of
this document or other SMSC literature, as well as the Terms of Sale Agreement, may be obtained by visiting SMSC’s website at http://www.smsc.com. SMSC is a registered
trademark of Standard Microsystems Corporation (“SMSC”). Product names and company names are the trademarks of their respective holders.
SMSC DISCLAIMS AND EXCLUDES ANY AND ALL WARRANTIES, INCLUDING WITHOUT LIMITATION ANY AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY,
FITNESS FOR A PARTICULAR PURPOSE, TITLE, AND AGAINST INFRINGEMENT AND THE LIKE, AND ANY AND ALL WARRANTIES ARISING FROM ANY COURSE
OF DEALING OR USAGE OF TRADE. IN NO EVENT SHALL SMSC BE LIABLE FOR ANY DIRECT, INCIDENTAL, INDIRECT, SPECIAL, PUNITIVE, OR CONSEQUENTIAL
DAMAGES; OR FOR LOST DATA, PROFITS, SAVINGS OR REVENUES OF ANY KIND; REGARDLESS OF THE FORM OF ACTION, WHETHER BASED ON CONTRACT;
TORT; NEGLIGENCE OF SMSC OR OTHERS; STRICT LIABILITY; BREACH OF WARRANTY; OR OTHERWISE; WHETHER OR NOT ANY REMEDY OF BUYER IS HELD
TO HAVE FAILED OF ITS ESSENTIAL PURPOSE, AND WHETHER OR NOT SMSC HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
USB 2.0 Hub and 10/100 Ethernet Controller
SMSC LAN9513/LAN9513i 3 Revision 1.2 (02-29-12)
PRODUCT PREVIEW
Overview
The LAN9513/LAN9513i is a high performance Hi-Speed USB 2.0 hub with a 10/100 Ethernet
controller. With applications ranging from embedded systems, desktop PCs, notebook PCs, printers,
game consoles, and docking stations, the LAN9513/LAN9513i is targeted as a high performance, low
cost USB/Ethernet and USB/USB connectivity solution.
The LAN9513/LAN9513i contains an integrated USB 2.0 hub, three integrated downstream USB 2.0
PHYs, an integrated upstream USB 2.0 PHY, a 10/100 Ethernet PHY, a 10/100 Ethernet Controller, a
TAP controller, and a EEPROM controller. A block diagram of the LAN9513/LAN9513i is provided in
Figure 1 .
The LAN9513/LAN9513i hub provides over 30 programmable features, including:
PortMap (also referred to as port remap) which provides flexible port mapping and disabling
sequences. The downstream ports of the LAN9513/LAN9513i hub can be reordered or disabled in any
sequence to support multiple platform designs’ with minimum effort. For any port that is disabled, the
LAN9513/LAN9513i automatically reorders the remaining ports to match the USB host controller’s port
numbering scheme.
PortSwap which adds per-port programmability to USB differential-pair pin locations. PortSwap allows
direct alignment of USB signals (D+/D-) to connectors avoiding uneven trace length or crossing of the
USB differential signals on the PCB.
PHYBoost which enables four programmable levels of USB signal drive strength in USB port
transceivers. PHYBoost attempts to restore USB signal integrity that has been compromised by system
level variables such as poor PCB layout, long cables, etc..
Figure 1 Internal Block Diagram
TAP
Controller
EEPROM
Controller
10/100
Ethernet
Controller
USB 2.0
Hub
LAN9513/LAN9513i
Ethernet
EEPROM
JTAG
USB
DP/DM
Downstream
USB PHY
Ethernet
PHY
Upstream
USB PHY
Downstream
USB PHY
Downstream
USB PHY
USB
DP/DM
USB
DP/DM
USB
DP/DM
USB 2.0 Hub and 10/100 Ethernet Controller
Revision 1.2 (02-29-12) 4 SMSC LAN9513/LAN9513i
PRODUCT PREVIEW
Package Outline
Figure 2 LAN9513/LAN9513i 64-QFN Package Definition
Table 1 LAN9513/LAN9513i 64-QFN Dimensions
MIN NOMINAL MAX REMARKS
A 0.80 0.85 1.00 Overall Package Height
A1 0.00 0.02 0.05 Standoff
A2 - 0.65 0.80 Mold Cap Thickness
D/E 8.90 9.00 9.10 X/Y Body Size
D1/E1 8.65 8.75 8.85 X/Y Mold Cap Size
D2/E2 7.20 7.30 7.40 X/Y Exposed Pad Size
L 0.30 0.40 0.50 Terminal Length
b 0.18 0.25 0.30 Terminal Width
e 0.50 BSC Terminal Pitch
K 0.35 - - Pin to Center Pad Clearance
USB 2.0 Hub and 10/100 Ethernet Controller
SMSC LAN9513/LAN9513i 5 Revision 1.2 (02-29-12)
PRODUCT PREVIEW
Notes:
1. All dimensions are in millimeters unless otherwise noted.
2. Dimension “b” applies to plated terminals and is measured between 0.15 and 0.30 mm from the terminal tip.
3. Details of terminal #1 identifier are optional, but must be located within the area indicated. The terminal #1
identifier may be either a mold or marked feature.
Figure 3 LAN9513/LAN9513i Recommended PCB Land Pattern
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Microchip:
LAN9514-JZX LAN9514-JZX-TR