IP1842A SERIES IP1843A SERIES SEME LAB TOP VIEW COMP 1 8 VREF V FB 2 7 VCC I SENSE 3 6 OUTPUT R T /C T 4 5 GROUND CURRENT MODE REGULATING PULSE WIDTH MODULATORS J Package - 8 Pin Ceramic DIP N Package - 8 Pin Plastic DIP D-8 Package - 8 Pin Plastic (150) SOIC FEATURES * * * * * * Guaranteed 1% reference voltage tolerance Accurate oscillator discharge current Guaranteed 10% frequency tolerance Low start-up current (<500 mA) Under voltage lockout with hysteresis Output state completely defined for all supply and input conditions * Interchangeable with IP and UC1842/3 series for improved operation * 500kHz Oscillator operation TOP VIEW COMP 1 14 VREF N/C 2 13 N/C V FB 3 12 VCC N/C 4 11 VC I SENSE 5 10 OUTPUT 6 9 GROUND R T /C T 7 8 POWER GROUND N/C D-14 Package - 14 Pin Plastic (150) SOIC Order Information Part Number IP1842A IP2842A IP3842A IP1843A IP2843A IP3843A J-Pack 8 Pin N-Pack 8 Pin D-8 8 Pin D-14 14 Pin Temp. Range -55 to +125C -25 to +85C 0 to +70C -55 to +125C -25 to +85C 0 to +70C Note: To order, add the package identifier to the part number. eg. IP1842AD-14 IP3843AJ ABSOLUTE MAXIMUM RATINGS (Tcase = 25C unless otherwise stated) VCC Supply Voltage IO Output Current Output Energy Analog Inputs Error Amp Output Sink Current Power Dissipation Derate @ Tamb > 50C Power Dissipation Derate @ Tamb > 50C Power Dissipation Derate @ Tcase > 25C Storage Temperature Range Lead Temperature PD PD PD TSTG TL Semelab plc. (low impedance source) (ICC < 30mA) (capacitive load) (pins 2 and 3) Tamb = 25C J, N Packages Tcase = 25C D Package Tcase = 25C J, N Packages (soldering, 10 seconds) Telephone (01455) 556565. Telex: 341927. Fax (01455) 552612. +30V Self limiting 1A 5J -0.3V to +VCC 10mA 1W 10mW/C 725mW 7.25mW/C 2W 16mW/C -65 to 150C +300C Prelim. 2/95 IP1842A SERIES IP1843A SERIES SEME LAB DESCRIPTION The IP1842A/IP1843A series of switching regulator control circuits contain all the functions necessary to implement off-line, current mode switching regulators, using a minimum number of external parts. Functions included are voltage reference, error amplifier, current sense comparator, oscillator, totem-pole output driver and under-voltage lockout circuitry. Although pin compatible with the standard IP1842/3 parts these devices offer improved performance in several areas. They also offer tighter specification and improved performance over the IP and UC1842/3 series, whilst retaining complete compatibility. BLOCK DIAGRAM VCC 7/12 UNDER-VOLTAGE LOCKOUT 34V REFERENCE 5V REGULATOR ENABLE G ND 5/9 16V (8.4V) 6V (0.5V) 8/14 VREF INTERNAL BIAS REG 2.5V VREF STATUS LATCH S 7/11 R VC 3.6V R T /CT 4/7 6/10 OSCILLATOR Q T ERROR AMP V FB 2/3 C OMP 1/1 I SENSE 3/5 TOGGLE FLIP FLOP * 5/8 OUTPUT POW ER GROUND S 2R R R 1V PWM LATCH CURRENT SENSE COMPARATOR * 1844A and 1845A series only. Values in brackets are for IP1845 series. PIN NUMBERS 1st Number - N, J and 8 Pin D Packages 2nd Num ber - 14 Pin D Package. RECOMMENDED OPERATING CONDITIONS VCC Supply Voltage 1 IO Output Current Analog Inputs 30V 0 to 200mA -0.3V to 3V (pins 2 and 3) 0 to 2mA Error Amp Output Sink Current Operating Ambient Temperature Range IP1842A , IP1843A IP2842A , IP2843A IP3842A , IP3843A -55 to 125C -25 to 85C 0 to 70C Notes: 1. Lower limit set by under voltage lockout specification. Semelab plc. Telephone (01455) 556565. Telex: 341927. Fax (01455) 552612. Prelim. 2/95 IP1842A SERIES IP1843A SERIES SEME LAB ELECTRICAL CHARACTERISTICS (Over Full Operating Temperature Range unless otherwise stated) Test Conditions 1 Parameter IP1842A , IP1843A IP2842A , IP2843A Min. Typ. Max. Min. IP3842A IP3843A Typ. 4.95 4.90 5.00 5.10 Max. Units REFERENCE SECTION Output Voltage IO = 1mA Input Regulation Output Regulation TJ = 25C 5.00 5.05 VCC = 12V to 25V 6 20 6 20 IO = 1mA to 20mA 6 25 6 25 0.2 0.4 0.2 0.4 Temperature Stability Total Output Variation Line, Load, Temp Output Noise Voltage f = 10Hz to 10kHz Long Term Stability TJ = 125C @ 1000Hrs Output Short Circuit Current 4.90 TJ = 25C 5.10 4.82 5 25 30 80 160 47 52 57 1 mV mV C V V 50 50 VREF = 0 5.18 V 5 25 mV 30 80 160 mA 47 52 57 kHz 0.2 1 % OSCILLATOR SECTION Frequency TJ = 25C Voltage Stability VCC = 12V to 25V 0.2 Temperature Stability TA = Min to Max 5 5 % Amplitude VPIN4 Peak to Peak 1.7 1.7 V TJ = 25C Discharge Current 7.8 TA = Min to Max 8.8 7.8 9 7 2.50 2.55 2.42 -0.3 -1 8.3 7 8.3 8.8 9 mA ERROR AMP SECTION Input Voltage VPIN1 = 2.5V 2.45 Input Bias Current Open Loop Voltage Gain VO = 2V to 4V Unity Gain Bandwidth Supply Voltage VCC = 12V to 25V Rejection 2.50 2.58 V -0.3 -2 A 65 90 65 90 dB 0.7 1 0.7 1 MHz 60 70 60 70 dB 2 6 2 6 Output Sink Current VPIN2 = 2.7V VPIN1 = 1.1V Output Source Current VPIN2 = 2.3V VPIN1 = 5V -0.5 -0.8 -0.5 -0.8 VOUT High VPIN2 = 2.3V RL = 15k 4.6 6 4.6 6 VOUT Low VPIN2 = 2.7V RL = 15k 0.7 1.1 0.7 mA 1.1 V NOTES 1. Test Conditions unless otherwise stated: VCC = 15V* , RT = 10k , CT = 3.3nF , f = 52kHz. *Adjust VCC above start threshold before setting at required level. All specifications apply over the full operating temperature range unless otherwise stated. (See Ordering Information for further details). Semelab plc. Telephone (01455) 556565. Telex: 341927. Fax (01455) 552612. Prelim. 2/95 IP1842A SERIES IP1843A SERIES SEME LAB ELECTRICAL CHARACTERISTICS (Over Full Operating Temperature Range unless otherwise stated) Test Conditions 1 Parameter IP1842A , IP1843A IP2842A , IP2843A Min. Typ. Max. Min. IP3842A IP3843A Typ. 2.85 3 3.15 2.85 3 3.15 V/V 0.9 1 1.1 0.9 1 1.1 V 60 70 60 70 Max. Units CURRENT SENSE SECTION Gain See Notes 2,3 Maximum Input Signal VPIN1 = 5V Supply Voltage (Note 2) VC = 12V to 25V Rejection dB Input Bias Current -2 -10 -2 -10 A Delay to Output 150 300 150 300 ns ISINK = 20mA 0.1 0.4 0.1 0.4 ISINK = 200mA 1.5 2.2 1.5 2.2 OUTPUT SECTION Output Low Level Output High Level ISOURCE = 20mA 13 13.5 13 13.5 ISOURCE = 200mA 12 13.5 12 13.5 V Rise Time CL = 1nF 50 150 50 150 Fall Time CL = 1nF 50 150 50 150 UVLO Saturation VCC = 6V 0.7 1.1 0.7 1.1 IL = 1mA V ns V UNDER-VOLTAGE LOCKOUT SECTION Upper Threshold IP1842A Series 15 16 17 14.5 16 17.5 (VCC) IP1843A Series 7.8 8.4 9 7.8 8.4 9 Lower Threshold IP1842A Series 9 10 11 8.5 10 11.5 (VCC) IP1843A Series 7 7.6 8.2 7 7.6 8.2 0.3 0.5 0.3 0.5 V V TOTAL STANDBY CURRENT Start-up Current Operating Supply VPIN2 = 0V IP1842A Series 11 15 11 15 Current VPIN3 = 0V IP1843A Series 14 17 14 17 VCC Zener Voltage ICC = 25mA 30 34 40 30 34 40 95 97 100 95 97 100 mA mA V PWM SECTION Maximum Duty Cycle Minimum Duty Cycle 0 0 % NOTES 1. Test Conditions unless otherwise stated: VCC = 15V* , RT = 10k , CT = 3.3nF , f = 52kHz. *Adjust VCC above start threshold before setting at required level. 2. Parameter measured at trip point of latch with VPIN2 = 0V 3. Gain defined as: All specifications apply over the full operating temperature range unless otherwise stated. (See Ordering Information for further details). Semelab plc. Telephone (01455) 556565. Telex: 341927. Fax (01455) 552612. VPIN1 VPIN3 0 VPIN3 0.8 A= Prelim. 2/95 IP1842A SERIES IP1843A SERIES SEME LAB APPLICATIONS INFORMATION Oscillator Waveforms and Maximum Duty Cycle LARGE R T SMALL C T VPIN4 (VPIN7 for 14 pin D package) INTERNAL CLOCK V REF OUTPUT - Max. Duty Cycle VPIN6 (VPIN10 for 14 pin D package) 8 RT RTCT 4 LARGE C T SMALL R T CT GND VPIN4 (VPIN7 for 14 pin D package) 5 INTERNAL CLOCK OUTPUT - Max. Duty Cycle VPIN6 (VPIN10 for 14 pin D package) Oscillator timing capacitor C T is charged by V REF tc 0.55 RTCT through RT and discharged by an internal current source. .0063 RT - 2.3 During the discharge time, the internal clock signal td RTCT Rn .0063 - 4 blanks the output to the low state. Selection of RT and 1 CT therefore determines both oscillator frequency and Resultant frequency f = (tc + td) maximum duty cycle. Charge and discharge times are determined by the formulae: ( ) For RT > 5k, Resultant frequency f 1.8 (RTCT) Open-Loop Laboratory Test Fixture VREF RT 4.7k VCC 2N2222 100k 1k ERROR AMP ADJUST 5k ISENSE ADJUST 1 COMP VREF 8 2 VFB VCC 7 3 ISENSE O/P 6 4 R T /C T GND 5 0.1 F 0.1 F 1k 1kW OUTPUT 4.7k GROUND CT High peak current associated with capacitive loads necessitate careful grounding techniques. Timing and bypass capacitors should be connected close to pin 5 in a single point ground. The transistor and 5K potentiometer are used to sample the oscillator wave form and apply an adjustable ramp to pin 3. Semelab plc. Telephone (01455) 556565. Telex: 341927. Fax (01455) 552612. Prelim. 2/95 IP1842A SERIES IP1843A SERIES SEME LAB TYPICAL PERFORMANCE CHARACTERISTICS ERROR AMPLIFIER OPEN-LOOP FREQUENCY RESPONSE OUTPUT SATURATION CHARACTERISTICS 100 TA = -55C 2 SOURCE SAT ( VCC- VOH) 1 0 60 -45 () TA = 25C 80 40 f 20 PH ASE (dB) VCC = 15V 3 VO LT AG E G AIN SAT U R AT IO N VO L TAG E (V) 4 -90 -135 AV 0 -180 SINK SAT (VOL ) 0 .01 .02 .03 .04 .05 .07 .1 .2 .3 .4 .5 .7 1.0 10 100 OUTPUT CURRENT, SOURCE / SINK (A) Semelab plc. Telephone (01455) 556565. Telex: 341927. Fax (01455) 552612. 1k 10k 100k 1M 10M FREQUENCY (Hz) Prelim. 2/95