Transient Voltage Suppression Diodes Surface Mount - 5000W > 5.0SMDJ series RoHS Pb Description The 5.0SMDJ series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Features Agency Approvals AGENCY AGENCY FILE NUMBER E230531 Maximum Ratings and Thermal Characteristics (TA=25OC unless otherwise noted) Parameter Symbol Value Unit Peak Pulse Power Dissipation at TA=25OC by 10x1000s waveform (Fig.1)(Note 1), (Note 2) PPPM 5000 W Power Dissipation on infinite heat sink at TA=50OC PM(AV) 6.5 W Peak Forward Surge Current, 8.3ms Single Half Sine Wave (Note 3) IFSM 300 A Maximum Instantaneous Forward Voltage at 100A for Unidirectional only VF 5.0 V TJ , TSTG -65 to 150 C Typical Thermal Resistance Junction to Lead RuJL 15 C/W Typical Thermal Resistance Junction to Ambient RuJA 75 C/W Operating Junction and Storage Temperature Range * Fast response time: typically less than 1.0ps from 0V to BV min * Excellent clamping capability * Low incremental surge resistance * Typical IR less than 5A above 22V VBR = 0.1% x VBR@25C x T * High Temperature soldering guaranteed: * Glass passivated chip 260C/40 seconds at junction terminals * 5000W peak pulse power Plastic package has * capability at 10x1000s Underwriters Laboratory waveform, repetition rate Flammability 94V-O (duty cycles):0.01% * Matte Tin Lead-free Plated * Halogen-Free * RoHS compliant * For surface mounted applications to optimize board space * Low profile package * Built-in strain relief * Typical maximum temperature coefficient Applications TVS devices are ideal for the protection of I/O Interfaces, VCC bus and other vulnerable circuits used in Telecom, Computer, Industrial and Consumer electronic applications. Notes: 1. Non-repetitive current pulse , per Fig. 3 and derated above TA = 25OC per Fig. 2. 2. Mounted on copper pad area of 0.31x0.31" (8.0 x 8.0mm) to each terminal. 3. Measured on 8.3ms single half sine wave or equivalent square wave for unidirectional device only,duty cycle=4 per minute maximum. 5.0SMDJ Series 1 Revision: November 15, 2011, 16:49 (c)2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to http://www.Littelfuse.com/series/5.0SSMDJ.html for current information. 5.0SMDJ Series 5.0SMDJ Series Transient Voltage Suppression Diodes Surface Mount - 5000W > 5.0SMDJ series Electrical Characteristics Part Number (Uni) Part Number (Bi) 5.0SMDJ12A 5.0SMDJ13A 5.0SMDJ14A 5.0SMDJ15A 5.0SMDJ16A 5.0SMDJ17A 5.0SMDJ18A 5.0SMDJ20A 5.0SMDJ22A 5.0SMDJ24A 5.0SMDJ26A 5.0SMDJ28A 5.0SMDJ30A 5.0SMDJ33A 5.0SMDJ36A 5.0SMDJ40A 5.0SMDJ43A 5.0SMDJ45A 5.0SMDJ48A 5.0SMDJ51A 5.0SMDJ54A 5.0SMDJ58A 5.0SMDJ60A 5.0SMDJ64A 5.0SMDJ70A 5.0SMDJ75A 5.0SMDJ78A 5.0SMDJ85A 5.0SMDJ90A 5.0SMDJ100A 5.0SMDJ110A 5.0SMDJ120A 5.0SMDJ130A 5.0SMDJ150A 5.0SMDJ160A 5.0SMDJ170A 5.0SMDJ12CA 5.0SMDJ13CA 5.0SMDJ14CA 5.0SMDJ15CA 5.0SMDJ16CA 5.0SMDJ17CA 5.0SMDJ18CA 5.0SMDJ20CA 5.0SMDJ22CA 5.0SMDJ24CA 5.0SMDJ26CA 5.0SMDJ28CA 5.0SMDJ30CA 5.0SMDJ33CA 5.0SMDJ36CA 5.0SMDJ40CA 5.0SMDJ43CA 5.0SMDJ45CA 5.0SMDJ48CA 5.0SMDJ51CA 5.0SMDJ54CA 5.0SMDJ58CA 5.0SMDJ60CA 5.0SMDJ64CA 5.0SMDJ70CA 5.0SMDJ75CA 5.0SMDJ78CA 5.0SMDJ85CA 5.0SMDJ90CA 5.0SMDJ100CA 5.0SMDJ110CA 5.0SMDJ120CA 5.0SMDJ130CA 5.0SMDJ150CA 5.0SMDJ160CA 5.0SMDJ170CA UNI BI Reverse Stand off Voltage VR (Volts) 5PEP 5PEQ 5PER 5PES 5PET 5PEU 5PEV 5PEW 5PEX 5PEZ 5PFE 5PFG 5PFK 5PFM 5PFP 5PFR 5PFT 5PFV 5PFX 5PFZ 5PGE 5PGG 5PGK 5PGM 5PGP 5PGR 5PGT 5PGV 5PGX 5PGZ 5PHE 5PHG 5PHK 5PHM 5PHP 5PHR 5BEP 5BEQ 5BER 5BES 5BET 5BEU 5BEV 5BEW 5BEX 5BEZ 5BFE 5BFG 5BFK 5BFM 5BFP 5BFR 5BFT 5BFV 5BFX 5BFZ 5BGE 5BGG 5BGK 5BGM 5BGB 5BGR 5BGT 5BGV 5BGX 5BGZ 5BHE 5BHG 5BHK 5BHM 5BHB 5BHR 12.0 13.0 14.0 15.0 16.0 17.0 18.0 20.0 22.0 24.0 26.0 28.0 30.0 33.0 36.0 40.0 43.0 45.0 48.0 51.0 54.0 58.0 60.0 64.0 70.0 75.0 78.0 85.0 90.0 100.0 110.0 120.0 130.0 150.0 160.0 170.0 Marking Breakdown Voltage VBR (Volts) @ IT MIN MAX Test Current IT (mA) 13.30 14.40 15.60 16.70 17.80 18.90 20.00 22.20 24.40 26.70 28.90 31.10 33.30 36.70 40.00 44.40 47.80 50.00 53.30 56.70 60.00 64.40 66.70 71.10 77.80 83.30 86.70 94.40 100.00 111.00 122.00 133.00 144.00 167.00 178.00 189.00 14.70 15.90 17.20 18.50 19.70 20.90 22.10 24.50 26.90 29.50 31.90 34.40 36.80 40.60 44.20 49.10 52.80 55.30 58.90 62.70 66.30 71.20 73.70 78.60 86.00 92.10 95.80 104.00 111.00 123.00 135.00 147.00 159.00 185.00 197.00 209.00 10 10 10 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Maximum Maximum Maximum Agency Clamping Peak Reverse Approval Voltage VC Pulse Leakage IR @ Ipp Current Ipp @ VR (V) (A) (A) 19.9 21.5 23.2 24.4 26.0 27.6 29.2 32.4 35.5 38.9 42.1 45.4 48.4 53.3 58.1 64.5 69.4 72.7 77.4 82.4 87.1 93.6 96.8 103.0 113.0 121.0 126.0 137.0 146.0 162.0 177.0 193.0 209.0 243.0 259.0 275.0 252.00 233.00 216.00 205.00 193.00 181.00 172.00 155.00 141.00 129.00 119.00 110.00 103.00 93.90 86.10 77.60 72.10 68.80 64.70 60.70 57.50 53.50 51.70 48.60 44.30 41.40 39.70 36.50 34.30 30.90 28.30 26.00 24.00 20.60 19.30 18.20 800 500 200 100 50 20 10 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 For Bidirectional type having VR of 20 volts and less,the IR limit is double. 5.0SMDJ Series 2 Revision: November 15, 2011, 16:49 (c)2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to http://www.Littelfuse.com/series/5.0SSMDJ.html for current information. X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X Transient Voltage Suppression Diodes Surface Mount - 5000W > 5.0SMDJ series Ratings and Characteristic Curves (T =25C unless otherwise noted) A Figure 2 - Peak Pulse Power or Current Derating Curve vs Initial Junction Temperature Figure 1 - Peak Pulse Power Rating Curve 100 Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage % PPPM-Peak Pulse Power (KW) 1000 100 10 1 80 60 40 20 0.31x0.31" (8.0x8.0mm) Copper Pad Area 0.1 0 0.000001 0.0000001 0.00001 0.0001 0.001 0 Figure 3 - Pulse Waveform Peak Value IPPM 100 Half Value IPPM IPPM ( ) 2 50 1000 10/1000sec. Waveform as defined by R.E.A 125 150 175 1.0 2.0 3.0 Uni-directional @ VR 100 Bi-directional @ VR td 0 Uni-directional V= OV 10 1 1.0 4.0 10.0 100.0 1000.0 VBR - Reverse Breakdown Voltage (V) Figure 6 - Maximum Non-Repetitive Peak Forward Surge Current Uni-Directional Only Figure 5 - Steady State Power Derating Curve 350 IFSM - Peak Forward Surge Current (A) PM(AV), Steady State Power Dissipation (W) 100 Bi-directional V= OV 10000 Cj (pF) IPPM- Peak Pulse Current, % IRSM TJ=25C Pulse Width(td) is defined as the point where the peak current decays to 50% of IPPM t-Time (ms) 0 25 50 75 100 125 150 175 TA-Ambient Temperature (C) 5.0SMDJ Series 75 100000 tr=10sec 6.5 6 5.5 5 4.5 4 3.5 3 2.5 2 1.5 1 0.5 0 50 Figure 4 - Typical Junction Capacitance 150 0 25 Tj-Initial temperature (C) td-Pulse Width (Sec.) 3 Revision: November 15, 2011, 16:49 300 250 200 150 100 50 0 1 10 100 Number of Cycles at 60 Hz (c)2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to http://www.Littelfuse.com/series/5.0SSMDJ.html for current information. Transient Voltage Suppression Diodes Surface Mount - 5000W > 5.0SMDJ series Soldering Parameters Lead-free assembly Pre Heat - Temperature Min (Ts(min)) 150C - Temperature Max (Ts(max)) 200C - Time (min to max) (ts) 60 - 180 secs Ramp-up TL Average ramp up rate (Liquidus Temp (TL) to peak 3C/second max TS(max) to TL - Ramp-up Rate 3C/second max Reflow - Temperature (TL) (Liquidus) 217C - Time (min to max) (ts) 60 - 150 seconds Peak Temperature (TP) 260 20 - 40 seconds Critical Zone TL to TP tL Ts(max) Ramp-down Ts(min) ts Preheat 25C Time within 5C of actual peak Temperature (tp) +0/-5 tp TP Temperature (T) Reflow Condition t 25C to Peak Time (t) C Ramp-down Rate 6C/second max Time 25C to peak Temperature (TP) 8 minutes Max. Do not exceed 280C Physical Specifications Environmental Specifications Weight 0.007 ounce, 0.21 grams Temperature Cycle JESD22-A104 Case JEDEC DO214AB. Molded plastic body over glass passivated junction Pressure Cooker JESD 22-A102 Polarity Color band denotes positive end (cathode) except Bidirectional. High Temp. Storage JESD22-A103 Terminal Matte Tin-plated leads, Solderable per JESD22-B102D HTRB JESD22-A108 Thermal Shock JESD22-A106 Dimensions DO-214AB (SMC J-Bend) Dimensions Cathode Band A C A B H D F E G Dimensions in inches and (millimeters) J K L I 5.0SMDJ Series Solder Pads (all dimensions in mm) 4 Revision: November 15, 2011, 16:49 Inches Millimeters Min Max Min Max 0.114 0.126 2.900 3.200 B 0.260 0.280 6.600 7.110 C 0.220 0.245 5.590 6.220 D 0.079 0.103 2.060 2.620 E 0.030 0.060 0.760 1.520 F - 0.008 - 0.203 G 0.305 0.320 7.750 8.130 H 0.006 0.012 0.152 0.305 I 0.129 - 3.300 - J 0.094 - 2.400 - K - 0.165 - 4.200 L 0.094 - 2.400 - (c)2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to http://www.Littelfuse.com/series/5.0SSMDJ.html for current information. Transient Voltage Suppression Diodes Surface Mount - 5000W > 5.0SMDJ series Part Numbering System Part Marking System 5.0SMDJ XXX C A Cathode Band XXXX XXXXX 5% VOLTAGE TOLERANCE BI-DIRECTIONAL F VOLTAGE SERIES Littelfuse Logo Marking Code Trace Code Marking Packaging Options Part number Component Package 5.0SMDJxxxXX DO-214AB 3000 Tape & Reel - 16mm/13" tape EIA STD RS-481 5.0SMDJxxxXX-T7 DO-214AB 500 Tape & Reel - 16mm/7" tape EIA STD RS-481 Packaging Option Quantity Packaging Specification Tape and Reel Specification 0.157 (4.0) 0.63 (16.0) Cathode 0.315 (8.0) Optional 7" 7.0 (187) 13" 13.0 (330) 0.80 (20.2) Arbor Hole Dia. 0.65 (16.4) 5.0SMDJ Series 0.059 DIA (1.5) Cover tape Dimensions are in inches (and millimeters). Direction of Feed 5 Revision: November 15, 2011, 16:49 (c)2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to http://www.Littelfuse.com/series/5.0SSMDJ.html for current information.