1
CSM_E3S-C_DS_E_6_1
Oil-resistant, Long-range Photoelectric Sensor with Metal Housing
E3S-C
Water- and Oil-resistant
Photoelectric Sensor with
Metal Housing Used for Long-
range Sensing
• Excellent resistance against the water and oil. Easy
application in locations with oil mist.
• Long-range sensing up to 30 m with Through-beam
models.
• Shock resistance rated at 1,000m/s2.
• Product lineup includes metal M12 pre-wired
connector models.
• NPN/PNP selector switch output.
Be sure to read Safety Precautions on
page 6.
Ordering Information
Sensors (Refer to Dimensions on page 8.)
* Through-beam Sensors are normally sold in sets that include both the Emitter and Receiver.
Orders for individual Emitters and Receivers are accepted.
Sensing method Appearance Connection method Sensing distance Model
Through-beam
(Emitter + Receiver) *
Pre-wired
E3S-CT11 2M
Emitter
E3S-CT11-L 2M
Receiver
E3S-CT11-D 2M
Pre-wired Connector (M12)
E3S-CT11-M1J 0.3M
Emitter
E3S-CT11-L-M1J 0.3M
Receiver
E3S-CT11-D-M1J 0.3M
Pre-wired
E3S-CT61 2M
Emitter
E3S-CT61-L 2M
Receiver
E3S-CT61-D 2M
Pre-wired Connector (M12)
E3S-CT61-M1J 0.3M
Emitter
E3S-CT61-L-M1J 0.3M
Receiver
E3S-CT61-D-M1J 0.3M
Retro-reflective
Pre-wired E3S-CR11 2M
Pre-wired Connector (M12) E3S-CR11-M1J 0.3M
Pre-wired E3S-CR61 2M
Pre-wired Connector (M12) E3S-CR61-M1J 0.3M
Diffuse-reflective
Pre-wired E3S-CD11 2M
E3S-CD12 2M
Pre-wired Connector (M12) E3S-CD11-M1J 0.3M
E3S-CD12-M1J 0.3M
Pre-wired E3S-CD61 2M
E3S-CD62 2M
Pre-wired Connector (M12) E3S-CD61-M1J 0.3M
E3S-CD62-M1J 0.3M
Red light Infrared light
Horizontal
30 m
Vertical
Horizontal
3 m
Vertical
Horizontal
700 mm
2 m
700 mm
2 m
Vertical
700 mm
2 m
700 mm
2 m
E3S-C
2
Accessories (Order Separately)
Slits (A Slit is not provided with Through-beam Sensors. Order a Slit separately if required.) (Refer to Dimensions on page 10.)
Reflectors (Reflector required for Retroreflective Sensors)
A Reflector is provided with the E39-R1 Sensor. For other Sensors, order a reflector separately if required.
(Refer to Dimensions on E39-L/F39-L/E39-S/E39-R.)
Note: 1. When using any reflector other than the provided one, use a sensing distance of approximately 0.7 times the typical value as a guide.
2. Refer to Reflectors on E39-L/F39-L/E39-S/E39-R for details.
* Values in parentheses indicate the minimum distance required between the Sensor and Reflector.
Mounting Brackets
Some Mounting Brackets are provided with the Sensor. Order other Mounting Brackets separately if required.
(Refer to Dimensions on E39-L/F39-L/E39-S/E39-R.)
Note: 1. When using a Through-beam Sensor, order one Connector for the Receiver and one for the Emitter.
2. Refer to Mounting Brackets on E39-L/F39-L/E39-S/E39-R for details.
Sensor I/O Connectors
(Models with Pre-wired Connectors: A Connector is not provided with the Sensor. Be sure to order a Connector separately.)
(Refer to Dimensions on XS2.)
Note: 1. When using a Through-beam Sensor, order one Connector for the Receiver and one for the Emitter.
2. For details on Sensor I/O Connectors and cables such as vibration-proof robot cables, refer to Introduction to Sensor I/O Connectors.
Slit width Sensing
distance
Minimum detect-
able object
(typical)
Model Quantity Remarks
0.5 mm × 11 mm 1.8 m 0.5-mm dia.
E39-S61
1 set each for
Emitter and Re-
ceiver
(8 Slits total)
(Snap-in Long Slit)
Can be used with the E3S-CT@1(-M1J)
Through-beam Sensor. Refer to page 10.
1 mm × 11 mm 3.5 m 1-mm dia.
2 mm × 11 mm 7 m 2-mm dia.
4 mm × 11 mm 15 m 2.6-mm dia.
Name Sensing distance (typical) Model Quantity Remarks
Reflectors 3 m (rated value) E39-R1 1 Provided with the E3S-CR@1 (-M1J) Retro-reflective Sensor.
4 m E39-R2 1 ---
Small Reflectors 1.5 m E39-R3 1 ---
750 mm E39-R4 1 ---
Tape Reflectors
700 mm (50 mm)*E39-RS1 1
Enables MSR function.1,100 mm (100 mm)*E39-RS2 1
1,400 mm (100 mm)*E39-RS3 1
Appearance Model Quantity Remarks
E39-L102 1 Provided with Horizontal Models.
E39-L103 1 Provided with Vertical Models.
E39-L85 1Mounting bracket for changing from E3S-
@@@@@42/44 to E3S-C Vertical Models.
E39-L86 1Mounting bracket for changing from E3S-
@@@@@43 to E3S-C Vertical Models.
E39-L87 1---
Cable Appearance Cable type Model
Standard
2 m
3-wire
XS2F-D421-DC0-A
5 m XS2F-D421-GC0-A
2 m XS2F-D422-DC0-A
5 m XS2F-D422-GC0-A
Straight
L-shape
E3S-C
3
Ratings and Specifications
*1. Refer to MSR function of Technical Guide (Technical version).
*2. NEMA: National Electrical Manufactures Association
Sensing
method Through-beam Retro-reflective
(with M.S.R. function) *1Diffuse reflective
Model
Horizontal
E3S-CT11(-M1J)
Horizontal
E3S-CR11(-M1J)
Horizontal
E3S-CD11(-M1J)
Horizontal
E3S-CD12(-M1J)
Item Vertical
E3S-CT61(-M1J)
Vertical
E3S-CR61(-M1J)
Vertical
E3S-CD61(-M1J)
Vertical
E3S-CD62(-M1J)
Sensing distance 30 m 3 m (when using E39-R1)
700 mm
(300 × 300 mm
white paper)
2 m
(300 × 300 mm
white paper)
Standard sensing
object Opaque, 15-mm dia. min. Opaque, 75-mm dia. min. ---
Differential travel --- 20% max. of sensing distance
Directional angle Emitter and Receiver: 3°
to15°3° to 10°---
Light source
(wavelength) Infrared LED (880 nm) Red LED (700 nm) Infrared LED (880 nm)
Power supply voltage 10 to 30 VDC including 10% (p.p) ripple
Current consumption 50 mA max. (Emitter 25 mA
max. Receiver 25 mA max.) 40 mA max.
Control output
Load power supply voltage: 30 VDC max.
Load current: 100 mA max. (Residual voltage: NPN output: 1.2 V max., PNP output: 2.0 V max.)
Open controller output (NPN/PNP selectable)
Light-ON/Dark-ON selectable
Protection circuits
Power supply reverse polari-
ty circuit protection, Output
short-circuit protection
Power supply reverse polarity protection, Output short-circuit protection,
Mutual interference prevention
Response time Operate or reset: 1 ms max. Operate or reset 2 ms max.
Sensitivity
adjustment One-turn adjuster Two-turn endless adjuster with an indicator
Ambient illumination
(Receiver side)
Incandescent lamp: 5,000 lx max.
Sunlight: 10,000 lx max.
Ambient temperature
range Operating: −25°C to 55°C, Storage: −40°C to 70°C (with no icing or condensation)
Ambient humidity
range Operating: 35% to 85%, Storage: 35% to 95% (with no condensation)
Insulation resistance 20 MΩ min. (at 500 VDC)
Dielectric strength 1,000 VAC, 50/60 Hz for 1 min
Vibration resistance Destruction: 10 to 2,000 Hz, 1.5-mm double amplitude or 300 m/s2 for 0.5 hours each in X, Y, and Z directions
Shock resistance Destruction: 1,000 m/s2 3 times each in X, Y, and Z directions
Degree of protection IEC 60529: IP67 (in-house standards: oil-resistant), NEMA: 6P (indoors only) *2
Connection method Pre-wired (standard cable length: 2 m) or Pre-wired M12 Connector (standard cable length: 0.3 m)
Weight (packed state)
Approx. 270 g
(Pre-wired cable)
Approx. 230 g
(Pre-wired Connector (M12))
Approx. 160 g
(Pre-wired cable)
Approx. 130 g
(Pre-wired Connector (M12))
Approx. 150 g
(Pre-wired cable)
Approx. 110 g
(Pre-wired Connector (M12))
Material
Case Zinc die-cast
Operation
panel cover PES (polyether sulfone)
Lens Methacrylic resin
Mounting
Bracket Stainless steel (SUS304)
Accessories Mounting Bracket (with screws), Adjustment screwdriver, Instruction manual, and Reflector (only for Retro-reflective
Sensors)
E3S-C
4
Engineering Data (Typical)
Parallel Operating Range
Through-beam Through-beam Retro-reflective
E3S-CT@ (-M1J) E3S-CT@ (-M1J) + E39-S61 Slit
(Order Separately)
E3S-CR@1 (-M1J) + E39-R1 Reflector
(Provided)
Operating Range
Diffuse-reflective
E3S-CD@@ (-M1J)
Excess Gain vs. Set Distance
Through-beam Retro-reflective Diffuse-reflective
E3S-CT@1 (-M1J) E3S-CR@1 (-M1J) + E39-R1 Reflector
(Provided)
E3S-CD@@ (-M1J)
2.5
2
1.5
1
0.5
0
−0.5
−1
−1.5
−2
−2.5
20 30 4010
Distance X (m)
Y
X
Distance Y (m)
800
600
400
200
0
−200
−400
−600
−800
4 8 12 16
Slit width: 1 mm
Slit width: 0.5 mm
Slit width: 2 mm
Slit width: 4 mm
Y
X
Distance X (m)
Distance Y (mm)
400
300
200
100
0
−100
−200
−300
−400
1 2 3 4
E39-R1 Reflector
Y
X
Distance X (m)
Distance Y (mm)
50
40
30
20
10
0
−10
−20
−30
−40
−50
21 3
Sensing object: white paper
300 × 300 mm
E3S-CD@2
E3S-CD@1
Distance X (m)
Y
X
Distance Y (mm)
500
300
100
50
30
10
5
3
1
Distance
(
m
)
0 10 20 30 40
Operating
level
Excess gain ratio
500
300
100
50
30
10
5
3
1
0 1 2 3 4
Reflector: E39-R1
Distance
(
m
)
Operating
level
Excess gain ratio
500
300
100
50
30
10
5
3
1
0 1 2 3
Sensing object: White paper 300 × 300 mm
E3S-CD@2
E3S-CD@1
Distance (m)
Operating
level
Excess gain ratio
E3S-C
5
I/O Circuit Diagrams
NPN Output
PNP Output
* Models numbers for Through-beam Sensors (E3S-CT@1(-M1J)) are for sets that include both the Emitter and Receiver.
The model number of the Emitter is expressed by adding "-L" to the set model number (example: E3S-CT11-L 2M), the model number of the Receiver, by adding "-D"
(example: E3S-CT11-D 2M.) Refer to Ordering Information to confirm model numbers for Emitter and Receivers.
Plug (Sensor I/O Connector)
Model Operation
mode Timing charts Operation
selector Output circuits
E3S-CT11(-M1J) *
E3S-CT61(-M1J) *
E3S-CR11(-M1J)
E3S-CR61(-M1J)
E3S-CD11(-M1J)
E3S-CD12(-M1J)
E3S-CD61(-M1J)
E3S-CD62(-M1J)
Light-ON L side
(LIGHT ON)
Dark-ON D side
(DARK ON)
Incident light
No incident light
ON
OFF
ON
OFF
Operate
Reset
Light indicator
(Red)
(Between brown
and black leads)
Output
transistor
Load
(e.g. relay)
Through-beam Model Receivers: Retro-re
f
lective Models, Re
f
lective Models
3
1
2 4
1
4
3
ZD
*
ZD
Photo-
electric
Sensor
main
circuit
PNP output
transistor
NPN output
transistor
NPN or PNP
output selector
Load
* Set the NPN or PNP selector to NPN.
Load
current
0 V
Pin 2 is not used.
Connector Pin Arrangement
10 to 30 VDC
Brown
Black
Control output
Blue
Light
indicator Stability
indicator
(Green)
(Red)
Incident light
No incident light
ON
OFF
ON
OFF
Operate
Reset
Light indicator
(Red)
(Between brown
and black leads)
Output
transistor
Load
(e.g. relay)
Through-beam Model Emitters
Note: Pins 2 and 4 are not used.
3
1
24
1
3
Power
indicator
(Red)
Brown
10 to 30 VDC
Blue
Photo-
electric
Sensor
main
circuit
Connector Pin Arrangement
Model Operation
mode Timing charts Operation
selector Output circuits
E3S-CT11(-M1J) *
E3S-CT61(-M1J) *
E3S-CR11(-M1J)
E3S-CR61(-M1J)
E3S-CD11(-M1J)
E3S-CD12(-M1J)
E3S-CD61(-M1J)
E3S-CD62(-M1J)
Light-ON L side
(LIGHT ON)
Dark-ON D side
(DARK ON)
Incident light
No incident light
ON
OFF
ON
OFF
Operate
Reset
Light indicator
(Red)
(Between blue
and black leads)
Output
transistor
Load
(e.g. relay)
3
1
24
1
4
3
ZD
*
ZD
Photo-
electric
Sensor
main
circuit
PNP output
transistor
NPN output
transistor
NPN or PNP
output selector
Load
* Set the NPN or PNP selector to NPN.
Load
current
0 V
Pin 2 is not used.
Connector Pin Arrangement
10 to 30 VDC
Brown
Black Control output
Blue
Light
indicator Stability
indicator
(Green)
(Red)
Through-beam Model Receivers: Retro-reflective Models, Reflective Models
Incident light
No incident light
ON
OFF
ON
OFF
Operate
Reset
Light indicator
(Red)
(Between blue
and black leads)
Output
transistor
Load
(e.g. relay)
Note: Pins 2 and 4 are not used.
3
1
24
1
3
Through-beam Model Emitters
Power
indicator
(Red)
Brown
10 to 30 VDC
Blue
Photo-
electric
Sensor
main
circuit
Connector Pin Arrangement
Note: Pin 2 is not used.
Clas-
sifica-
tion
Conductor Connector
pin No. Application
DC
Brown 1 Power supply (+V)
--- 2 ---
Blue 3 Power supply (0 V)
Black 4 Output
2
4
13
1
2
3
4
Brown
Blue
Black
Terminal No.
XS2F-D421-DC0-A
Refer to Introduction
to Sensor I/O
connectors for
details.
E3S-C
6
Nomenclature
Horizontal Model Vertical Model
Note: The sensitivity adjuster on Through-beam and Retro-reflective Models is
different.
*1. Use the output selector to select the type of output transistor, NPN or PNP.
*2. Use the operation selector to select the operation mode.
Safety Precautions
Refer to Warranty and Limitations of Liability.
This product is not designed or rated for ensuring
safety of persons either directly or indirectly.
Do not use it for such purposes.
Do not use the product in atmospheres or environments that exceed
product ratings.
● Designing
Fuzzy Mutual Interference Prevention Function
If Reflective Sensors are installed side by side, each Sensor may be
influenced by the light emitted from the other Sensors.
The fuzzy mutual interference prevention function of the E3S-C
enables the E3S-C to monitor any light interference for a certain
period before the E3S-C starts emitting light so that the E3S-C can
retrieve the intensity and frequency of the light interference as data.
Using this data, the E3S-C estimates with fuzzy inference the risk of
the malfunctioning of the E3S-C and controls the timing of the E3S-
C’s light emission.
When the risk is low:
The E3S-C waits until there is no light interference and emits light.
When the risk is high:
The E3S-C emits light between each period of light interference.
● Wiring
Cable
•The E3S-C uses an oil-resistive cable to ensure oil resistivity.
•Do not allow the cable to be bent to a radius of less than 25 mm.
● Mounting
Mounting
•When mounting the E3S-C, do not hit the E3S-C with a hammer, or
the E3S-C will loose watertightness.
•Use M4 screws to mount the E3S-C. The tightening torque of each
screw must be 1.18 N·m maximum.
Mounting Bracket
•When mounting the E3S-C with the mounting bracket so that
sensing objects will be in the direction of the mechanical axis, use
the optical axis lock holes.
•If it is not possible to mount the E3S-C so that the sensing objects
will be in the direction the mechanical axis, move the E3S-C
upwards, downwards, to the left, or to the right and secure the E3S-
C in the center of the range where the light indicator will be lit, at
which time make sure that the stability indicator is lit.
Direct Mounting
Mount the E3S-C as shown in the following illustration.
Mounting with M4 Screws
Mounting with M3 Screws
Optical Axis Adjustment
Optical Lock Holes
By inserting screws into the
optical axis lock holes, the
Mounting Bracket will be in the
direction of the optical axis of the
E3S-C.
Min Max
SL
PNP
SENS
D·ON
NPN L·ON
E3S-CD12
Stability
indicator
(green)
Light
indicator
(red)
Operation panel
cover
Sensitivity
adjuster
Operation
selector *2
Model number
Output selector *1
PNP
NPN
D
ON
L
ON
SENS
SL
MaxMin
Operation panel
cover
Stability indicator
(green)
Light indicator
(red)
Sensitivity
adjuster
Operation
selector *2
Output selector *1
WARNING
Precautions for Correct Use
Emission
pattern
Light
interference
Emission
pattern
Light
interference
Two, 4.5 dia.
through holes
M4
M4 hole
M4 hole
Two, M3
M4 hole
M4 hole
M3
Optical
axis
Mounting axis
Four optical
axis lock
holes
(
M4
)
E3S-C
7
● Adjusting
Optical Axis of Through-beam Sensor
The E3S-C Through-beam Models incorporates two lenses, one of
which will be used as shown in the following illustration. When using
a Slit, the Slit must be on the side where the lens to be used is located.
Horizontal Model Vertical Model
Water Resistance
To ensure the water resistance of the E3S-C, tighten the screws of the
operation panel cover to a torque of 0.34 N·m to 0.54 N·m.
● Others
Oil and Chemical Resistance
•Although the E3S-C is oil-resistance, refer to the following table
before using the E3S-C in places where oil may be sprayed on the
E3S-C.
•Tests were carried out with the following oils and it was certified that
the E3S-C resists these oils.
Note: 1. The E3S-C maintained a minimum insulation resistance of 100 MΩ
after the E3S-C was dipped in all the above oils at a temperature of
50°C for 240 hours.
2. When using the E3S-C in a place where an oil other than the ones
listed above is sprayed on the E3S-C, refer to the above kinematic
viscosity and ph values. The location may be suitable for the E3S-C if
the kinematic viscosity and pH values of the oil are close to the above
kinematic viscosity and pH values, but make sure that the oil does not
contain any additive that may have a negative influence on the E3S-C.
Lens in use. The Slit
must be on this side.
Unused lens
Lens in use.
Unused lens
Oil Product name Kinematic viscosity
(mm2/s (cst)) at 40°CPH
Lubricating oil Velocite No.3 2.02
---
Water insoluble
machining oil Yushiron Oil No. 2 ac Less than 10
Water soluble
machining oil
Yushiroken EC50T-3
---
7 to 9.5
Yushiron Lubic HWC68 7 to 9.9
Griton 1700D 7 to 9.2
Yushiroken S50N 7 to 9.8
E3S-C
8
Dimensions
Sensors
Note: Models numbers for Through-beam Sensors (E3S-CT11(-M1J)) are for sets that include both the Emitter and Receiver.
The model number of the Emitter is expressed by adding "-L" to the set model number (example: E3S-CT11-L 2M), the model number of the Receiver, by adding "-D"
(example: E3S-CT11-D 2M.) Refer to Ordering Information to confirm model numbers for Emitter and Receivers.
(Unit: mm)
Tolerance class IT16 applies to dimensions in this datasheet unless otherwise specified.
50 *2
Light indicator (red)
Stability
indicator
(green)
22.2
9.2
4.2
6.2 38.2
8.3
29.5
17.3
25.420.8
2.2
4
18
9.3
23
Lens (17 × 11) Optical axis
1.5
Two, M4
Stainless steel
(SUS304)
4.2
20
M3 × 5
4-dia. vinyl-insulated round cable
Standard length: 300 mm
M12 × 1
20.4
20
25.4
Two, M4
18.5
A*1
*1. The Mounting Bracket can be attached to side A.
*2. The Emitters for Through-beam Sensors only have the power indicator (red).
*3. The Emitter cable is 4-dia.vinyl-insulated round cable with 2 conductors (conductor cross section: 0.3 mm2,
insulator diameter: 1.3 mm) and a standard length of 2 m.
4-dia. vinyl-insulated round cable with 3 conductors
(Conductor cross section: 0.2 mm2 (AWG 24),
Insulator diameter: 1.2 mm),
Standard length: 2 m *3
With Mounting Bracket Attached
Mounting Holes
Pre-wired Connector (-M1J)
Emitter: E3S-CT@@-L
Receiver: E3S-CT@@-D
Through-beam (Horizontal)
E3S-CT11(-M1J)
E3S-C
9
Note: Models numbers for Through-beam Sensors (E3S-CT61(-M1J)) are for sets that include both the Emitter and Receiver.
The model number of the Emitter is expressed by adding "-L" to the set model number (example: E3S-CT61-L 2M), the model number of the Receiver, by adding "-D"
(example: E3S-CT61-D 2M.) Refer to Ordering Information to confirm model numbers for Emitter and Receivers.
20
57
15.8 7.4
Optical axis
Optical axis
22.2
12.9
4.2
4.2 9.2
4.2
12.9
20
25.4
31
43.8
1.5
12
32.2
2.2
7.2
Stability indicator (green)
Light indicator (red)*2
20.2
Two, M4
5.8
23
A*1M3 × 5
23.2
Lens (17 × 11)
M12 × 1
20.4
25.4
Two, M4
Stainless steel
(SUS304)
4-dia. vinyl-insulated round cable with 3 conductors
(Conductor cross section: 0.2 mm2 (AWG24),
Insulator diameter: 1.2 mm),
Standard length: 2 m *3
With Mounting Bracket Attached
Mounting Holes
4-dia. vinyl-insulated round cable
Standard length: 300 mm
Pre-wired Connector (-M1J)
*1. The Mounting Bracket can be attached to side A.
*2. The Emitters for Through-beam Sensors only have the power indicator (red).
*3. The Emitter cable is 4-dia.vinyl-insulated round cable with 2 conductors (conductor cross section: 0.3 mm2,
insulator diameter: 1.3 mm) and a standard length of 2 m.
Through-beam (Vertical)
E3S-CT61(-M1J)
50
Light indicator (red)
Stability indicator
(green)
22.2
9.2
4.2
6.2 38.2
8.3
29.5
17.3
25.420.8
2.2
4
18
9.3
1
23 9
Optical axis
Receiver
Emitter
1.5
Two, M4
Stainless steel
(SUS304)
4.2
20
M3 × 5
M12 × 1
20.4
20
18.5
A*
*The Mounting Bracket can be attached to side A.
25.4
Two, M4
Mounting Holes
Lens (17 × 11)
Pre-wired Connector (-M1J)
4-dia. vinyl-insulated round cable
Standard length: 300 mm
With Mounting Bracket Attached
4-dia. vinyl-insulated round cable with 3 conductors
(Conductor cross section: 0.2 mm2 (AWG24),
Insulator diameter: 1.2 mm),
Standard length: 2 m
Retro-/Diffuse-reflective (Horizontal)
E3S-CR11(-M1J)
E3S-CD11(-M1J)
E3S-CD12(-M1J)
E3S-C
10
Accessories (Order Separately)
Reflectors
Refer to E39-L/F39-L/E39-S/E39-R for details.
Mounting Brackets
Refer to E39-L/F39-L/E39-S/E39-R for details.
20
57
Emitter
Receiver 9
52.4
20.8
Optical axis
22.2
12.9
4.2
4.2 9.2
4.2
12.9
20
25.4
31
43.8
1.5
12
32.2
2.2
7.2
Stability indicator (green)
Light indicator (red)
20.2
Two, M4
5.8
23
A*1M3 × 5
23.2
M12 × 1
20.4
25.4
Two, M4
*The Mounting Bracket can be attached to side A.
Stainless steel
(SUS304)
4-dia. vinyl-insulated round cable with 3 conductors
(Conductor cross section: 0.2 mm2 (AWG24),
Insulator diameter: 1.2 mm),
Standard length: 2 m
Mounting Holes
Lens (17 × 11)
Pre-wired Connector (-M1J)
4-dia. vinyl-insulated round cable
Standard length: 300 mm
With Mounting Bracket Attached
Retro-/Diffuse-reflective (Vertical)
E3S-CR61(-M1J)
E3S-CD61(-M1J)
E3S-CD62(-M1J)
A
20.1
0.2
3.8
6.2 11.
8
1
11
6.5
20
Snap-in Long Slit (For Through-beam Models)
E39-S61
Dimension
A (mm) Material Quantity
0.5
Stainless
steel
1 set each for
Emitter/Receiver
(8 Slits total)
1
2
4
Read and Understand This Catalog
Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or
comments.
Warranty and Limitations of Liability
WARRANTY
OMRON's exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specified)
from date of sale by OMRON.
OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT, MERCHANTABILITY, OR
FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS. ANY BUYER OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALONE HAS
DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. OMRON DISCLAIMS ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED.
LIMITATIONS OF LIABILITY
OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR COMMERCIAL LOSS
IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED ON CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT
LIABILITY.
In no event shall the responsibility of OMRON for any act exceed the individual price of the product on which liability is asserted.
IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY, REPAIR, OR OTHER CLAIMS REGARDING THE PRODUCTS UNLESS
OMRON'S ANALYSIS CONFIRMS THAT THE PRODUCTS WERE PROPERLY HANDLED, STORED, INSTALLED, AND MAINTAINED AND NOT
SUBJECT TO CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE MODIFICATION OR REPAIR.
Application Considerations
SUITABILITY FOR USE
OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to the combination of products in the customer's
application or use of the products.
At the customer's request, OMRON will provide applicable third party certification documents identifying ratings and limitations of use that apply to the
products. This information by itself is not sufficient for a complete determination of the suitability of the products in combination with the end product,
machine, system, or other application or use.
The following are some examples of applications for which particular attention must be given. This is not intended to be an exhaustive list of all possible
uses of the products, nor is it intended to imply that the uses listed may be suitable for the products:
•
Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this catalog.
•
Nuclear energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles,
safety equipment, and installations subject to separate industry or government regulations.
•
Systems, machines, and equipment that could present a risk to life or property.
Please know and observe all prohibitions of use applicable to the products.
NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE
SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCTS ARE PROPERLY RATED AND
INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM.
PROGRAMMABLE PRODUCTS
OMRON shall not be responsible for the user's programming of a programmable product, or any consequence thereof.
Disclaimers
CHANGE IN SPECIFICATIONS
Product specifications and accessories may be changed at any time based on improvements and other reasons.
It is our practice to change model numbers when published ratings or features are changed, or when significant construction changes are made.
However, some specifications of the products may be changed without any notice. When in doubt, special model numbers may be assigned to fix or
establish key specifications for your application on your request. Please consult with your OMRON representative at any time to confirm actual
specifications of purchased products.
DIMENSIONS AND WEIGHTS
Dimensions and weights are nominal and are not to be used for manufacturing purposes, even when tolerances are shown.
PERFORMANCE DATA
Performance data given in this catalog is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the
result of OMRON’s test conditions, and the users must correlate it to actual application requirements. Actual performance is subject to the OMRON
Warranty and Limitations of Liability.
ERRORS AND OMISSIONS
The information in this document has been carefully checked and is believed to be accurate; however, no responsibility is assumed for clerical,
typographical, or proofreading errors, or omissions.
2010.9
In the interest of product improvement, specifications are subject to change without notice.
OMRON Corporation
Industrial Automation Company
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2010 All Right Reserved.
