1 2 DWG. NO. SA25594 NOTE: L O.D. 1. MATERIALS: AS NOTED. 2. PLATING: TIN PLATED. 3. SURFACE TREATMENT : IRIDITE OVER CADMIUM PLATE. * THESE SIZES NOT IRIDITED. SCALE 8:1 INNER HYRING OUTER HYRING DIAMETER (IN INCH.) L=.25 INSTALLATION TOOLS RATCHET HYTOOLS HYTOOLS HYPRESSES Y10R M8ND Y10NCP Y8ND Y10C-1 DIE SET DIE SET DIE SET DIE SET NO. NO. NO. NO. R7VST CAT. NO. COLOR I.D. O.D. MR8PV TYPE INCLUDES DIE YOC70 *TIN .101 .124 MR8PV-14S YOC80 BLUE .125 .156 MR8PV-S N8VST R8VST N8VST YOC90 PURPLE .149 .179 MR8PV-S, MR8PV-1S N10VST R14VST-5 N10VST YOC100 YELLOW .156 .196 MR8PV-S, MR8PV-1S N10VST R14VST-5 N10VST YOC110 BLUE .180 .204 MR8PV-S, MR8PV-1S N10VST R14VST-5 N10VST YOC112 BLUE .175 .215 MR8PV-S, MR8PV-1S N12VST R14VST-5 N12VST YOC120 ORANGE .187 .227 MR8PV-S, MR8PV-1S N12VST R14VST-5 N12VST YOC128 *TIN .199 .235 MR8PV-S, MR8PV-1S N12VST R14VST-5 N12VST YOC130 YELLOW .207 .243 MR8PV-S, MR8PV-1S MR8PV-10S N12VST N13VST R14VST-5 R14VST-3 N12VST N13VST YOC140 GREEN .219 .250 N14VST R14VST-5 N14VST MR8PV-1S MR8PV-11S YOC150 ORANGE .235 .266 MR8PV-2 N16VT R18VT-3 N16VT YOC160 YELLOW .261 .297 MR8PV-2 N16VT R18VT-3 N16VT YOC180 PURPLE .281 .331 MR8PV-2 R18VT-3 YOC190 GREEN .300 .335 MR8PV-2 R18VT-3 YOC200 YELLOW .312 .362 MR8PV-3 R20VT R22VT YOC220 ORANGE .344 .394 MR8PV-4 MR8PV-11S YOC240 BLUE .375 .406 MR8PV-7 R24VT MR8PV-6 R25VT YOC250 RED .405 .453 Y0C320G1 PURPLE .500 .550 R29VT Y0C371G1 *TIN .580 .620 R32VT YOC370 *TIN .705 .755 MD5-36 CAT. NO. COLOR I.D. O.D. YIC046 *TIN .046 .070 YIC058 YELLOW .058 .083 YIC063 RED .063 .088 YIC071 GREEN .071 .096 YIC080 BLUE .080 .104 YIC090 ORANGE .090 .114 YIC101 YELLOW .101 .124 YIC109 RED .109 .131 YIC115 *TIN .115 .146 YIC124 GREEN .124 .145 YIC125 YELLOW .125 .156 YIC134 ORANGE .134 .156 YIC150 BLUE .150 .181 YIC156 RED .166 .191 YIC180 GREEN .180 .204 YIC194 BLUE .194 .255 YIC219 *TIN .219 .243 YIC261 BLUE .261 .297 YIC297 RED .297 .337 YIC375G1 *TIN .375 .423 YIC472G1 *TIN .472 .516 YIC495G1 *TIN .495 .535 YIC340 *TIN .340 .390 THIRD ANGLE PROJECTION TOLERANCES UNLESS OTHERWISE SPECIFIED No. OF PLACES INCH [mm] ONE PLACE #.1 [ #3] TWO PLACES #0.02 [ #.5] THREE PLACES # 0.005 ANGLES #1 $ 2 INNER HYRING (BRASS) OUTER HYRING (COPPER) BRAID PROPER SELECTION OF HYRINGS: OUTER FERRULES MAY BE USED IN COMBINATION WITH ANY INNER FERRULES, DEPENDING ON THE SIZE OF THE CONDUCTOR, THE THICKNESS OF THE SHIELD AND THE SIZE OF THE GROUND TAP. HOWEVER, DUE TO VARIATION IN INSULATION DIAMETER AND BRAID CONSTRUCTION, THE RECOMMENDED BASIS FOR SIZE SELECTION FOR SHIELDED CABLE IS A FACTORY-INSTALLED, SAMPLE CONNECTION MADE ON ACTUAL WIRE TO BE USED. IF IT IS NOT CONVENIENT TO FORWARD WIRE SAMPLES, SIZES CAN BE DETERMINED AS FOLLOWS: DETERMINE O.D. OF INNER INSULATION. SELECT INNER HYRING FROM CHART ABOVE HAVING I.D. A MINIMUM OF .005 GREATER THAN THIS DIAMETER. TO THE O.D. OF THIS FERRULE ADD .025 (FOR SINGLE BRAID) PLUS .040 FOR WIRE TAP (UPTO #18), IF USED, AND SELECT OUTER FERRULE HAVING I.D. ATLEAST EQUAL TO THIS FIGURE. THE PROPER CRIMPING TOOL FOR EACH OUTER HYRING IS LISTED ON TABLE. SUPERSEDES: SA-25594-16 W REVISED PER ECN 11866 CJM 12-12-12 SDH 12-12-12 REV DESCRIPTION BY DATE CHKD DATE DRAWING TITLE COLORED FERRULES CAT NO. LINEAR MEASURE: B HYLUG DIAMETER (IN INCH.) L=.31 YIC & YOC_____(SEE TABLE) CAGE NO: 09922 SIZE: B APPROVAL THE INFORMATION CONTAINED IN THIS DRAWING IS CONFIDENTIAL AND MAY NOT BE DISCLOSED WITHOUT WRITTEN CONSENT FROM SOURIAU USA, INC. THIS DRAWING IS A CONTROLLED DOCUMENT FOR SOURIAU USA, INC. IT IS SUBJECT TO CHANGE WITHOUT NOTIFICATION. CONTACT THE DOCUMENT CONTROL CENTER FOR THE LATEST REVISION. I.D. CUSTOMER INTERPRET THIS DRAWING IN ACCORDANCE WITH ASME Y14.5M-1994. DRAWN: CHKD : DSGN : MFG : QC : DRAWING DRAWING NVM 11-14-11 11-14-11 SDH mm-dd-yy XXX 11-14-11 DH 11-14-11 BB SCALE: 8:1 NO. REV W SA25594 www.souriau.com 1 1 OF 1 PRO-E A