2 1
1
2
B
A
THE INFORMATION CONTAINED IN THIS DRAWING IS CONFIDENTIAL AND MAY NOT BE
DISCLOSED WITHOUT WRITTEN CONSENT FROM SOURIAU USA, INC. THIS DRAWING IS A CONTROLLED DOCUMENT FOR SOURIAU USA, INC.
IT IS SUBJECT TO CHANGE WITHOUT NOTIFICATION.
CONTACT THE DOCUMENT CONTROL CENTER FOR THE LATEST REVISION.
DWG. NO.
PRO-E
I.D. O.D.
L
OUTER HYRING
L=.25 DIAMETER
(IN INCH.)
INSTALLATION TOOLS
RATCHET HYTOOLS HYTOOLS HYPRESSES
CAT. NO. COLOR I.D. O.D. MR8PV TYPE
INCLUDES DIE
M8ND
DIE SET
NO.
Y10R
Y10C-1
DIE SET
NO.
Y10NCP
DIE SET
NO.
Y8ND
DIE SET
NO.
YOC70 *TIN .101 .124 MR8PV-14S R7VST
YOC80 BLUE .125 .156 MR8PV-S N8VST R8VST N8VST
YOC90 PURPLE .149 .179 MR8PV-S, MR8PV-1S N10VST R14VST-5 N10VST
YOC100 YELLOW .156 .196 MR8PV-S, MR8PV-1S N10VST R14VST-5 N10VST
YOC110 BLUE .180 .204 MR8PV-S, MR8PV-1S N10VST R14VST-5 N10VST
YOC112 BLUE .175 .215 MR8PV-S, MR8PV-1S N12VST R14VST-5 N12VST
YOC120 ORANGE .187 .227 MR8PV-S, MR8PV-1S N12VST R14VST-5 N12VST
YOC128 *TIN .199 .235 MR8PV-S, MR8PV-1S N12VST R14VST-5 N12VST
YOC130 YELLOW .207 .243 MR8PV-S, MR8PV-1S
MR8PV-10S
N12VST
N13VST
R14VST-5
R14VST-3
N12VST
N13VST
YOC140 GREEN .219 .250 MR8PV-1S
MR8PV-11S N14VST R14VST-5 N14VST
YOC150 ORANGE .235 .266 MR8PV-2 N16VT R18VT-3 N16VT
YOC160 YELLOW .261 .297 MR8PV-2 N16VT R18VT-3 N16VT
YOC180 PURPLE .281 .331 MR8PV-2 R18VT-3
YOC190 GREEN .300 .335 MR8PV-2 R18VT-3
YOC200 YELLOW .312 .362 MR8PV-3 R20VT
YOC220 ORANGE .344 .394 MR8PV-4
MR8PV-11S R22VT
YOC240 BLUE .375 .406 MR8PV-7 R24VT
YOC250 RED .405 .453 MR8PV-6 R25VT
Y0C320G1 PURPLE .500 .550 R29VT
Y0C371G1 *TIN .580 .620 R32VT
YOC370 *TIN .705 .755 MD5-36
INNER HYRING
L=.31 DIAMETER
(IN INCH.)
CAT. NO. COLOR I.D. O.D.
YIC046 *TIN .046 .070
YIC058 YELLOW .058 .083
YIC063 RED .063 .088
YIC071 GREEN .071 .096
YIC080 BLUE .080 .104
YIC090 ORANGE .090 .114
YIC101 YELLOW .101 .124
YIC109 RED .109 .131
YIC115 *TIN .115 .146
YIC124 GREEN .124 .145
YIC125 YELLOW .125 .156
YIC134 ORANGE .134 .156
YIC150 BLUE .150 .181
YIC156 RED .166 .191
YIC180 GREEN .180 .204
YIC194 BLUE .194 .255
YIC219 *TIN .219 .243
YIC261 BLUE .261 .297
YIC297 RED .297 .337
YIC375G1 *TIN .375 .423
YIC472G1 *TIN .472 .516
YIC495G1 *TIN .495 .535
YIC340 *TIN .340 .390
1 OF 1
www.souriau.com
INTERPRET THIS DRAWING IN
ACCORDANCE WITH ASME Y14.5M-1994.
W
SA25594
REVDRAWING NO.
CUSTOMER
DRAWING SCALE: 8:1
11-14-11
QC : BB
APPROVAL
11-14-11
MFG : DH
mm-dd-yy
DSGN : XXX
11-14-11
CHKD : SDH
SIZE: B
CAGE NO: 09922
11-14-11
DRAWN: NVM
YIC & YOC_____(SEE TABLE)
CAT NO.
COLORED FERRULES
DRAWING TITLE
W REVISED PER ECN 11866 CJM
12-12-12
SDH
12-12-12
REV DESCRIPTION BY
DATE
CHKD
DATE
ANGLES #1$
# 0.005THREE PLACES
#0.02 [#.5]TWO PLACES
#.1 [#3]ONE PLACE
INCH [mm]
No. OF PLACES
TOLERANCES
UNLESS OTHERWISE SPECIFIED
THIRD ANGLE PROJECTION
LINEAR
MEASURE:
SA25594
SUPERSEDES: SA-25594-16
NOTE:
1. MATERIALS: AS NOTED.
2. PLATING: TIN PLATED.
3. SURFACE TREATMENT : IRIDITE OVER CADMIUM PLATE.
* THESE SIZES NOT IRIDITED.
PROPER SELECTION OF HYRINGS:
OUTER FERRULES MAY BE USED IN COMBINATION WITH ANY INNER FERRULES, DEPENDING
ON THE SIZE OF THE CONDUCTOR, THE THICKNESS OF THE SHIELD AND THE SIZE OF THE
GROUND TAP. HOWEVER, DUE TO VARIATION IN INSULATION DIAMETER AND BRAID
CONSTRUCTION, THE RECOMMENDED BASIS FOR SIZE SELECTION FOR SHIELDED CABLE IS
A FACTORY-INSTALLED, SAMPLE CONNECTION MADE ON ACTUAL WIRE TO BE USED. IF IT IS
NOT CONVENIENT TO FORWARD WIRE SAMPLES, SIZES CAN BE DETERMINED AS FOLLOWS:
DETERMINE O.D. OF INNER INSULATION. SELECT INNER HYRING FROM CHART ABOVE HAVING
I.D. A MINIMUM OF .005 GREATER THAN THIS DIAMETER. TO THE O.D. OF THIS FERRULE
ADD .025 (FOR SINGLE BRAID) PLUS .040 FOR WIRE TAP (UPTO #18), IF USED, AND SELECT
OUTER FERRULE HAVING I.D. ATLEAST EQUAL TO THIS FIGURE. THE PROPER CRIMPING TOOL
FOR EACH OUTER HYRING IS LISTED ON TABLE.
HYLUG
INNER HYRING (BRASS)
OUTER HYRING (COPPER)
BRAID
SCALE 8:1
