FH30-80S-0.3SHW(05) - Hirose Connector

2013.11w1

■Features

Strong actuator retention

Actuator will not be dislodged when operating under harsh

conditions.

2. Rotating Flip–Lock actuator

Rotating actuator permits easy insertion and retention of the

FPC.

Tactile sensation confirms complete FPC insertion and reliable

mechanical and electrical connection.

FPC position hold

Tabs on each side of the FPC assure correct placement and

hold in the connector prior to closing of the actuator.

4. Accepts standard FPC thickness

0.3mm thick standard Flexible Printed Circuit (FPC) can be

used.

5. Easy solderability on the PC board

The soldering leads are on 0.6 mm or 0.8 mm pitch, exiting on

the front and back of the connector.

6. Board placement with automatic equipment

Flat upper surface and tape and reel packaging facilitate vacuum

pick-up and placement. Standard reel packaging contains 1000

connectors.

7. Conductive traces on the PCB can run under

the connector

No exposed contacts on the bottom of the connector.

8. Halogen-free*

* As defined by IEC61249-2-21

Br-900ppm maximum, Cl-900ppm maximum,

Cl + Br combined-1,500ppm maximum

Simple FPC insertion

Lock

Strong actuator construction

0.3 or 0.4 mm pitch, 3 mm above the board, Flip-Lock actuator,

Flexible Printed Circuit ZIF connectors

FH30 Series

Enclosed shaft of the actuator

prevents it from dislocation

FPC positioning tab

Current rating(Note 1)

Voltage rating

FH30 Series●0.3 or 0.4mm pitch, 3mm above the board, Flip-Lock actuator, Flexible Printed Circuit ZIF connectors

■Product Specifications

Item Specification Conditions

100 V DC

0.3 mm pitch: 90 Vrms AC / 1 minute

0.4mm pitch: 150 Vrms AC / 1 minute

1 mA AC

20 cycles

Frequency: 10 to 55 Hz, single amplitude of 0.75 mm

10 cycles in each of the 3 directions

Acceleration of 981m/s2, 6 ms duration,

sine half-wave, 3 cycles in each of the 3 axis

96 hours at 40°C and humidity of 90 to 95%

Temperature: -40°C ➝+15°C to 35°C ➝+85°C➝+15°C to 35°C

Time:

-30

➝

2 to 3

➝

+30

➝

+2 to 3

5 cycles

Reflow: At the recommended temperature profile

Manual soldering: 350°C for 5 seconds

1. Insulation resistance 500 Mø min.

2. Withstanding voltage No flashover or insulation breakdown

3. Contact resistance 150 mø max.

* Including FPC conductor resistance

4. Durability Contact resistance: 150 mø max.

No damage, cracks, or parts dislocation

5. Vibration

No electrical discontinuity of 1μs or longer

Contact resistance: 150 mø max.

No damage, cracks, or parts dislocation

6. Shock

No electrical discontinuity of 1μs or longer

Contact resistance: 150 mø max.

No damage, cracks, or parts dislocation

Humidity (Steady state)

Contact resistance: 150 mø max.

Insulation resistance: 50Mø min.

No damage, cracks, or parts dislocation

8. Temperature cycle

Contact resistance: 150 mø max.

Insulation resistance: 50Mø min.

No damage, cracks, or parts dislocation

Resistance to soldering heat

No deformation of components affecting

performance.

Note1: When passing the current through all of the contacts, use 70% of the rated current.

Note2: Includes temperature rise caused by current flow.

Note3: The term "storage" refers to products stored for a long period prior to mounting and use.

The operating temperature and humidity range covers the non-conducting condition of connectors after installation on a

board.

■Materials

Insulator LCP FH30 series Color:Gray UL94V-0

FH30M series Color:Beige

Contacts Phosphor bronze Gold plated --------------

Part Material Finish Remarks

Recommended FPC Thickness: 0.3±0.05, Gold plated contact pads

Ratings

0.3 mm pitch

0.15 A

30 Vrms AC

0.4 mm pitch

0.3 A

50 Vrms AC

Operating temperature range -40 to +85°C (Note 2)

Operating humidity range Relative humidity 90% max.

(No condensation)

Storage temperature range -10 to +50°C (Note 3)

Storage humidity range Relative humidity 90% max.

(No condensation)

■Ordering information

qSeries name : FH

wSeries No. : 30

eBlank : 0.3mm pitch

M : 0.4 mm pitch

rNumber of contacts : FH30 series 60, 80, 90

FH30M series 80, 96

tContact pitch : 0.3 mm, 0.4 mm

yContact type :

SHW(SMT horizontal staggered mounting)

uPlating specifications : (05)…Gold plated

(98)…Gold plated, 500 pieces/reel

FH 30 M - 80S - 0.3 SHW (05)

1 2 3 4 5 6 7

FH30 Series●0.3 or 0.4mm pitch, 3mm above the board, Flip-Lock actuator, Flexible Printed Circuit ZIF connectors

■Dimensions

4.2

Vacuum pick-up surface

0.8 0.8

6.55

Number of contacts indicator

(E: FPC insertion slot dimension)

(0.12)

4.85

Notes 1: The coplanarity of each terminal lead is within 0.1.

2: Packaged on tape and reel only. Check packaging specification.

3: Slight variations in color of the plastic compounds do not affect form ,fit or function of the connector.

4: After reflow, the terminal plating may change color, however this does not represent a quality issue.

Tape and reel packaging (1,000 pieces/reel, 500 pieces/reel).

Order by number of reels.

Part Number

FH30-60S-0.3SHW(05)

FH30-80S-0.3SHW(05)

FH30-90S-0.3SHW(05)

FH30M-80S-0.4SHW(05)

FH30M-96S-0.4SHW(05)

580-0105-8-05

580-0100-4-05

580-0106-0-05

580-0102-0-05

580-0103-2-05

0.3

0.4

CL No.

Number of Contacts

FPC contact pitch

All dimensions: mm

A B C D E Q R

21.9

27.9

30.9

35.8

42.2

17.7

23.7

26.7

31.6

17.4

23.4

26.4

31.2

37.6

17.4

23.4

26.4

31.2

37.6

18.35

24.35

27.35

32.25

38.65

0.3

0.4

0.6

0.8

0.2μm thick gold plated over 1 to

5μm thick nickel underplating

0.25±0.03(Metal mask)

1.7±0.1 3.95±0.1

1.7±0.1

R±0.05

R±0.05 0.3±0.03(Land)

Mark side

0.25±0.03(Metal mask)

C±0.05Q±0.05

B±0.05

D±0.05

0.3±0.03(Land)

J±0.1

0.3±0.05

2.2±0.1

R0.2

Q±0.02

R±0.02

B±0.03

F±0.05

G±0.1

0.3±0.07

0.3 +0.04

-0.03

0.3±0.07

2.65±0.2 (0.5)

3.2±0.3

0.07±0.070.1±0.05

0.3 +0.04

-0.03

1.3±0.1(0.8)

No.1

No.2

No(n-1)

No (n)

4.2±0.3

1.4±0.1

(C0.5)

H MIN

0.05 MIN

0±0.1

Detail A

Note 1 :

Conductor width shall be 0.1±0.05 if FPC has plating bars.

Recommended metal mask thickness: t=0.15

1. This specification is a recommendation for the construction of the FH30 Series FPC (t=0.3 ± 0.05).

2. For details about the construction, please contact the FPC manufacturers.

■

FH30 Series Recommended FPC Construction

1. Using Single-sided FPC Material Name

Copper foil

Base adhesive

Base film

Reinforcement material adhesive

Stiffener

Material

Material Thickness

(μm)

Cu 1oz

Thermosetting adhesive

Polyimide 1 mil thick

Thermosetting adhesive

Polyimide 7 mil thick

Covering film layer

Cover adhesive

Polyimide 1 mil thick

175

(25)

Surface treatment

0.2μm thick gold plated over 1 to

5μm thick nickel underplating

Total 293

2. Using Double-sided FPC

3. Precautions

* To prevent release of the FPC due to it’s bending, use of the double-sided FPC with copper foil on the back side is NOT RECOMMENDED.

Material Name

Covering layer film

Cover adhesive

Material

Material Thickness

(μm)

Polyimide 1 mil thick

Through-hole copper

Copper foil

Base adhesive

Base film

Base adhesive

Cu 1/2oz

Thermosetting adhesive

Polyimide 1 mil thick

Thermosetting adhesive

Surface treatment 3

Copper foil

Cover adhesive

Covering film layer

Reinforcement material adhesive

Stiffener

Cu 1/2oz

Thermosetting adhesive

Polyimide 1 mil thick

Thermosetting adhesive

Polyimide 4 mil thick

(18)

100

Total 297

■

Recommended PCB mounting

pattern and metal mask dimensions

■Recommended FPC Dimensions

Part Number

FH30-60S-0.3SHW(05)

FH30-80S-0.3SHW(05)

FH30-90S-0.3SHW(05)

FH30M-80S-0.4SHW(05)

FH30M-96S-0.4SHW(05)

580-0105-8-05

580-0100-4-05

580-0106-0-05

580-0102-0-05

580-0103-2-05

CL No.

Number of Contacts

0.3

0.4

FPC contact pitch

17.7

23.7

26.7

31.6

17.4

23.4

26.4

31.2

37.6

17.4

23.4

26.4

31.2

37.6

18.3

24.3

27.3

32.2

38.6

18.8

24.8

27.8

32.7

39.1

19.3

25.3

28.3

33.2

39.6

20.3

26.3

29.3

34.2

40.6

0.3

0.4

0.6

0.8

B C D F G H J Q R

All dimensions: mm

FH30 Series●0.3 or 0.4mm pitch, 3mm above the board, Flip-Lock actuator, Flexible Printed Circuit ZIF connectors

■Packaging Specifications

Unreeling direction

1.35±0.1

(4.9)

(N)

(6.8)

12±0.1

2±0.15

4±0.1

Ø1.5

+0.1

1.75±0.1M±0.1

L±0.1

K±0.3

1.7 +0.15

1.5+0.1

0.4±0.1

●Embossed Carrier Tape Dimensions ●Reel Dimensions

(Ø13)

(T: INSIDE)

(U: OUTSIDE)

(Ø80)

(Ø380)

End section Mounting section Lead section (400mm min.)

Embossed carrier tape

Top cover tape

No connector inserted

(10 pockets min.)

No connector inserted

(10 pockets min.)

FH30 Series●0.3 or 0.4mm pitch, 3mm above the board, Flip-Lock actuator, Flexible Printed Circuit ZIF connectors

Tape and reel packaging (1,000 pieces/reel).

Part Number

FH30-60S-0.3SHW(05)

FH30-80S-0.3SHW(05)

FH30-90S-0.3SHW(05)

FH30M-80S-0.4SHW(05)

FH30M-96S-0.4SHW(05)

CL No.

580-0105-8-05

580-0100-4-05

580-0106-0-05

580-0102-0-05

580-0103-2-05

Number of Contacts

40.4

52.4

20.2

26.2

22.1

28.1

31.1

42.4

45.4

57.4

49.4

61.4

All dimensions: mm

MAX 250ç

Start

Temperature(ç)

Time (Seconds)

25ç (60 sec.)

(30 sec.)

90 to 120 sec.

Preheating

Soldering

100

150 150ç

200ç

230ç

200

250

HRS test condition

Solder method :Reflow, IR/hot air

Environment :Room air

Solder composition :Paste, 96.5%Sn/3.0%Ag/0.5%Cu

(Senju Metal Industry, Co., Ltd.'s Part

Number:M705-221CM5-32-10.5)

Test board :Glass epoxy FH30:45∞80∞1.6mm thick

FH30M:70∞130∞1.6mm

thick

Land dimensions :0.3mm∞1.7mm

Metal mask :0.15mm thick

0.25mm∞1.7mm

The temperature profiles shown are based on the above

conditions.

In individual applications the actual temperature may

vary,depending on solder paste type, volume / thickness and

board size / thickness. Consult your solder paste and

equipment manufacturer for specific recommendations.

■Temperature Profile

●Using Lead-free Solder Paste

FH30 Series●0.3 or 0.4mm pitch, 3mm above the board, Flip-Lock actuator, Flexible Printed Circuit ZIF connectors

■Operation and Precautions

Operation and Precautions

wFPC Insertion

Orient the FPC with the contact pads facing down.

Insert in the connector at an angle, assuring that the

positioning tabs are placed in the corresponding

positioning tab areas on both sides of the insulator

body.

Lower the FPC to a position parallel to the mounting

surface.

Verify the correct position by slightly pulling

horizontally on the FPC.

Positioning tab area (each side)

eActuator closing after the FPC is fully inserted.

Rotate the actuator down to a full stop, pushing it at

the center.

rRemoving the FPC

Carefully rotate the actuator up, lifting it at the center.

Lift the FPC slightly to clear the positioning tabs and

withdraw it from the connector.

Positioning part

qInstall on the PC board with the actuator open.

FH30 Series●0.3 or 0.4mm pitch, 3mm above the board, Flip-Lock actuator, Flexible Printed Circuit ZIF connectors

■Precautions

Operation and Precautions

Rotation shaft

qActuator operation

The actuator rotates at the center of it’s shaft, as

illustrated in the figure below.

Be careful not to apply excessive force when

operating the actuator from the open position (before

the FPC has been inserted).

Exercise care not to touch the contacts with

fingernails or any other object.

wFPC Insertion and closing of the actuator.

Do not insert the FPC on an angle as illustrated in the

photograph below.

eMake sure that the FPC does not rub against the

insertion slot or the contacts, as illustrated on the

figure below.

Properly insert the FPC positioning tabs into the

corresponding areas on both sides of the insulator

body.

Incorrect FPC insertion

Correct FPC insertion

During the closing of the actuator do not pull up or

push on it directly down.

Do not grasp the actuator and pull on it (photograph

below).

FH30 Series●0.3 or 0.4mm pitch, 3mm above the board, Flip-Lock actuator, Flexible Printed Circuit ZIF connectors

Operation and Precautions

Closing of the actuator.

Rotate down pushing it at the center or evenly at

each end, as shown on the photographs below. Do

not push at one end only.

rOpening of the actuator

Rotate up, lifting it at the center or evenly at each end

of the actuator.

Do not lift at one end only.

tForces to the FPC after insertion and closing of

the actuator.

Do not apply upward pull-force to the FPC close to the

connector.

If a need arise to route the FPC upward, assure that

it is NOT transferring any forces to the closed

actuator.

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Hirose Electric:

FH30-80S-0.3SHW FH30-80S-0.3SHW(05) FH30M-80S-0.4SHW(05) FH30M-96S-0.4SHW(05) FH30-90S-

0.3SHW(05) FH30-80S-0.3SHW(98) FH30M-96S-0.4SHW(98) FH30-60S-0.3SHW(98) FH30-90S-0.3SHW(98)

FH30-60S-0.3SHW(05) FH30M-80S-0.4SHW(98)