MCC 1N4614 THRU 1N4125 omponents 20736 Marilla Street Chatsworth !"# $ % !"# TM Micro Commercial Components Features * * * * * Zener Voltage Range = 1.8V to 47V Double Slug Type Construction Metallurgical Bonded Construction Lead Free Finish/Rohs Compliant (Note1) ("P"Suffix designates Compliant. See ordering information) Moisture Sensitivity: Level 1 per J-STD-020C 500mW Silicon Zener Diodes Mechanical Data * * DO-35 Case: Double slug type, hermetically sealed glass Marking : Cathode band and type number D Maximum Ratings Max. Steady State Power Dissipation at TL<75OC, Lead Length=3/8" Junction Temperature Storage Temperature Range Thermal Resistance, Junction to lead @3/8" lead length from body Symbol Value Units PD 500 mW TJ TSTG 175 -55 to 175 A Cathode Mark o C C B o D RthJL o C/W 250 C Electrical Characteristics @ 25C Unless Otherwise Specified Max. Forward Voltage @ I F=200mA Note: Symbol Maximum Unit VF 1.1 V DIMENSIONS 1. Lead in Glass Exemption Applied, see EU Directive Annex 5. Revision: 6 DIM A B C D INCHES MIN ------1.000 www.mccsemi.com 1 of 5 MAX .166 .079 .020 --- MM MIN ------25.40 MAX 4.2 2.00 .52 --- NOTE 2009/07/06 MCC 1N4614 thru 1N4125 TM Micro Commercial Components ELECTRICAL CHARACTERISTICS (TA = 25C unless otherwise noted, VF = 1.1 V Max @ IF = 200mA for all types) (3) Zener Voltage (2) Device (1) Device Marking Maximum Reverse Leakage Current (4) Zener Impedance (5) Zener (IZM) IR@VR ZZT@IZT Current VZ (Volts) @IZT=250UA Min Nom 1N4615- 1.71 1.90 1.8 2.0 1.89 2.10 1N4616 1N4616----- 2.09 2.2 2.31 1N4617 1N4617- 2.28 1N4618 1N4618--- 2.4 2.7 2.52 2.835 2.85 3.135 3.42 3.0 3.15 3.3 3.465 95 90 87 85 3.6 3.78 83 3.705 4.085 3.9 4.3 4.095 80 4.515 4.7 5.1 4.935 5.355 77 75 70 5.6 6.2 5.88 6.51 65 61 6.8 7.14 7.875 8.61 56 1N4614 1N4614 1N4615 2.565 1N4619 1N4619 -- 1N4620 1N4620 -- 1N4621 1N4621- 1N4622 1N4622-- 1N4623 1N4623-- 1N4624 1N4624--- 1N4625 1N4626 1N46251N4626------ 4.465 4.845 5.32 1N4627 1N4627-- 5.89 1N4099 1N4099 1N4100 1N4100 1N4101 1N4101 1N4102 1N4102 1N4103 1N4104 1N4105 1N4106 1N4107 1N4108 1N4109 1N4110 1N4111 1N4112 1N4113 1N4114 1N4115 1N4116 1N4117 1N4118 1N4119 1N4120 1N4121 1N4122 1N4123 1N4124 1N4125 1N4103 1N41041N4105 1N4106 1N4107 1N4108 1N4109 1N4110 1N4111 1N4112 1N4113 1N4114 1N4115 1N4116 1N4117 1N4118 1N4119 1N4120 1N4121 1N4122 1N4123 1N4124 1N4125 ----- 6.46 7.125 7.79 8.265 8.645 9.5 10.45 11.4 12.35 13.3 14.25 15.2 16.15 17.1 18.05 19 20.9 22.8 23.75 25.65 26.6 28.5 31.35 34.2 37.05 40.85 44.65 7.5 8.2 8.7 9.1 10 11 12 13 14 15 16 17 18 19 20 22 24 25 27 28 30 33 36 39 43 47 Max mA 120 110 100 51 46 9.135 44 42 9.555 38 35 32 29 27 25 24 22 21 20 19 17 16 1 15 14 1 14 13 12 11 9.8 8.9 8.1 10.5 11.55 12.6 13.65 14.7 15.75 16.8 17.85 18.9 19.95 21 23.1 25.2 26.25 28.35 29.4 31.5 34.65 37.8 40.95 45.15 49.35 uA( Max) Volts ohm(Max) 7.5 5.0 4.0 2.0 1 1 1400 1.0 0.8 1 1500 1600 7.5 7.5 1 1 1 1.5 2 1200 1250 1300 1650 1700 5.0 4.0 2 2 10.0 10.0 10.0 3 1600 1550 3 1500 4 1400 10.0 10.0 10.0 1.0 5 5.17 1200 200 5.70 6.24 6.61 200 1.0 1.0 1.0 .05 .05 .05 .05 .05 .05 .05 .05 .05 .01 .01 .01 .01 .01 .01 .01 .01 .01 .01 .01 .01 1650 200 200 6.92 200 7.60 8.44 8.12 9.857 10.65 11.40 12.15 12.92 13.67 14.44 15.20 16.72 18.25 19.00 20.45 21.28 22.80 25.08 27.38 29.65 32.65 35.75 200 200 200 200 200 100 100 100 100 150 150 150 150 150 150 200 200 200 200 200 250 250 NOTES: 1. TOLERANCE AND TYPE NUMBER DESIGNATION (VZ) The type numbers listed have a standard tolerance on the nominal zener voltage of 5%. 2. ZENER VOLTAGE (VZ) MEASUREMENT Nominal zener voltage is measured with the device junction in the thermal equilibrium . the lead temperature (TL) at 30C 1C and 3/8" lead length. at 3. MAXIMUM ZENER CURRENT RATINGS (IZM) This data was calculated using nominal voltages. The maximum handing current capability on a worst case basis is limited by the actual zener voltage at the opertation piont and the power derating curve. . 4.Reverse Leakage Current(IR)reverse leakage current are guaranteed and measured at VR shown on the table . 5. Zener Impedance(ZZT) Derivation The Zener impedance is derived from the 60 cycle ac voltage.which results when an Ac . current having an rms value to 10% of the DC zener current (IZT) is superimposed on IZT. Revision: 6 www.mccsemi.com 2 of 5 2009/07/06 MCC 1N4614 thru 1N4125 TM VZ , TEMPERA TURE COEFFICIENT (mV/ C) Micro Commercial Components +12 +10 +8 +6 +4 +2 RANGE VZ @ IZT (NOTE 2) 0 -2 -4 2 4 3 5 7 6 8 9 10 11 12 V Z , ZENER VOLTAGE (VOLTS) Figure 1. Range for Units to 12 Volts TEMPERATURE COEFFICIENT (mV/C) +6 VZ @ IZ TA= 25 C +4 +2 20mA 0 0.01mA 1mA VZ , -2 NOTE: BELOW 3 VOLTS AND ABOVE 8 VOL TS NOTE: CHANGES IN ZENER CURRENT DO NOT NOTE: AFFECT TEMPERATURE COEFFICIENTS -4 3 6 5 4 8 7 V Z , ZENER VOL TAGE (VOLTS) Figure 2. Effect of Zener Current 1000 TA = 25 C 500 0V BIAS C, CAP ACIT ANCE (pF) 200 100 1V BIAS 50 20 10 50% OF V Z BIAS 5 2 1 1 2 5 10 20 50 100 V Z, ZENER VOLTAGE (VOLTS) Figure 3. Typical Capacitance 2.4-100 Volts Revision: 6 www.mccsemi.com 3 of 5 2009/07/06 MCC 1N4614 thru 1N4125 TM Micro Commercial Components Ppk , PEAK SURGE POWER (WATTS) 100 70 50 RECT ANGULAR WAVEFORM T J = 25C PRIOR TO INITIAL PULSE 11V-91V NONREPETITIVE 30 5% DUTY CYCLE 1.8V-10V NONREPETITIVE 20 10 10% DUTY CYCLE 7 5 20% DUTY CYCLE 3 2 1 0.01 0.02 0.05 0.1 0.2 0.5 1 2 5 10 20 50 100 200 500 1000 PW, PULSE WIDTH (ms) Figure 4. Maximum Surge Power 1.8-91 Volts 1000 Z Z , DYNAMIC IMPEDANCE (OHMS) 500 T J = 25C iZ (rms) = 0.1 Iz(dc) VZ = 2.7V f = 60 Hz 200 47V 100 27V 50 20 6.2V 10 5 2 1 0.1 0.2 0.5 1 2 5 10 20 50 100 IZ , ZENER CURRENT (mA) Figure 5. Effect of Zener Current on Zener Impedance TJ = 25C 1000 MAXIMUM iZ (rms) = 0.1 IZ (dc) 500 f = 60Hz IZ = 1mA I F , FOR WARD CURRENT (mA) Z Z , DYNAMIC IMPEDANCE (OHMS) 1000 700 500 200 100 70 50 5mA 20 20mA 10 7 5 2 MINIMUM 200 100 50 75 C 20 10 25 C 5 150 C 0 C 2 1 1 1 2 3 5 7 10 20 30 50 70 100 0.4 V Z , ZENER VOLTAGE (VOLTS) 0.6 0.7 0.8 0.9 1 1.1 V F , FOR WARD VOLTAGE (VOLTS) Figure 6. Effect of Zener Voltage on Zener Impedance Revision: 6 0.5 Figure 7. Typical Forward Characteristics www.mccsemi.com 4 of 5 2009/07/06 MCC TM Micro Commercial Components Ordering Information Device Packing (Part Number)-TP Tape&Reel; 10Kpcs/Reel (Part Number)-AP Ammo Packing;5Kpcs/AmmoBox (Part Number)-BP Bulk;500pcs/Bag ***IMPORTANT NOTICE*** Micro Commercial Components Corp . reserves the right to make changes without further notice to any product herein to make corrections, modifications , enhancements , improvements , or other changes . Micro Commercial Components Corp . does not assume any liability arising out of the application or use of any product described herein; neither does it convey any license under its patent rights ,nor the rights of others . The user of products in such applications shall assume all risks of such use and will agree to hold Micro Commercial Components Corp . and all the companies whose products are represented on our website, harmless against all damages. ***APPLICATIONS DISCLAIMER*** Products offer by Micro Commercial Components Corp . are not intended for use in Medical, Aerospace or Military Applications. www.mccsemi.com Revision: 6 5 of 5 2009/07/06