General Description
The MAX9768 mono 10W Class D speaker amplifier
provides high-quality, efficient audio power with an inte-
grated volume control function.
The MAX9768 features a 64-step dual-mode (analog or
digitally programmable) volume control and mute func-
tion. The audio amplifier operates from a 4.5V to 14V
single supply and can deliver up to 10W into an 8Ω
speaker with a 14V supply.
A selectable spread-spectrum mode reduces EMI-radiat-
ed emissions, allowing the device to pass EMC testing
with ferrite bead filters and cable lengths up to 1m. The
MAX9768 can be synchronized to an external clock,
allowing synchronization of multiple Class D amplifiers.
The MAX9768 features high 77dB PSRR, low 0.08%
THD+N, and SNR up to 97dB. Robust short-circuit and
thermal-overload protection prevent device damage
during a fault condition. The MAX9768 is available in a
24-pin thin QFN-EP (4mm x 4mm x 0.8mm) package
and is specified over the extended -40°C to +85°C tem-
perature range.
Applications
Features
10W Output (8Ω, PVDD = 14V, THD+N = 10%)
Spread-Spectrum Modulation
Meets EN55022B EMC with Ferrite Bead Filters
Amplifier Operation from 4.5V to 14V Supply
64-Step Integrated Volume Control (I2C or Analog)
Low 0.08% THD+N (RL= 8Ω, POUT = 6W)
High 77dB PSRR
Two tON Times Offered
MAX9768—220ms
MAX9768B—15ms
Low-Power Shutdown Mode (0.5µA)
Short-Circuit and Thermal-Overload Protection
MAX9768
10W Mono Class D Speaker
Amplifier with Volume Control
________________________________________________________________
Maxim Integrated Products
1
19-0854; Rev 2; 11/08
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,
or visit Maxim’s website at www.maxim-ic.com.
EVALUATION KIT
AVAILABLE
Pin Configuration located at end of data sheet.
Ordering Information
Note: All devices are specified over the -40°C to +85°C oper-
ating temperature range.
+
Denotes a lead-free/RoHS-compliant package.
*
EP = Exposed pad.
PART PIN-PACKAGE tON (ms)
MAX9768ETG+ 24 TQFN-EP* 220
MAX9768BETG+ 24 TQFN-EP* 15
MUTE
SHDN
SPEAKER
AUDIO
INPUT
FILTERLESS
CLASS D
SPEAKER
OUTPUT
ANALOG OR
I2C VOLUME
CONTROL
3.3V 4.5V TO 14V
MAX9768
Simplified Block Diagram
MAX9768 EMI WITH FERRITE BEAD FILTERS
(VDD = 12V, 1m CABLE, 8Ω LOAD)
FREQUENCY (MHz)
900
800100 200 300 500 600400 700
5
10
15
20
AMPLITUDE (dBμV/m)
25
30
35
40
0
0 1000
OVER 20dB MARGIN
TO EN55022B LIMIT
Notebook Computers
Flat-Panel Displays
Multimedia Monitors
GPS Navigation
Systems
Security/Personal
Mobile Radio
MAX9768
10W Mono Class D Speaker
Amplifier with Volume Control
2 _______________________________________________________________________________________
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS
(VPVDD = 12V, VDD = 3.3V, VGND = VPGND = 0, VSHDN = VDD, VMUTE = 0; Max volume setting; speaker load resistor connected
between OUT+ and OUT-, RL= , unless otherwise noted. CBIAS = 2.2µF, C1 = C2 = 0.1µF, CIN = 0.47µF, RIN = 20kΩ, RF= 30kΩ,
SSM mode. Filterless modulation mode (see the
Functional Diagram/Typical Application Circuit
). TA= TMIN to TMAX, unless otherwise
noted. Typical values are at TA= +25°C.) (Note 1)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
PVDD to PGND........................................................-0.3V to +16V
VDD to GND..............................................................-0.3V to +4V
SCLK, SDA/VOL to GND ..........................................-0.3V to +4V
FB, SYNCOUT ............................................-0.3V to (VDD + 0.3V)
BOOT_ to OUT_........................................................-0.3V to +4V
OUT_ to GND ...........................................-0.3V to (PVDD + 0.3V)
PGND to GND ......................................................-0.3V to +0.3V
Any Other Pin to GND ..............................................-0.3V to +4V
OUT_ Short-Circuit Duration.......................................Continuous
Continuous Current (PVDD, PGND, OUT_) ..........................2.2A
Continuous Input Current (Any Other Pin) .......................±20mA
Continuous Input Current (FB_) .......................................±60mA
Continuous Power Dissipation (TA= +70°C)
Single-Layer Board:
24-Pin Thin QFN 4mm x 4mm,
(derate 20.8mW/°C above +70°C).................................1.67W
Multilayer Board:
24-Pin Thin QFN 4mm x 4mm,
(derate 27.8mW/°C above +70°C).................................2.22W
θJA, Single-Layer Board…...........................................….48°C/W
θJA, Multilayer Board ...................................................….36°C/W
Operating Temperature Range ...........................-40°C to +85°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) ................................+300°C
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
GENERAL
Speaker Supply Voltage
Range PVDD Inferred from PSRR test 4.5 14.0 V
Supply Voltage Range VDD Inferred from PSRR and UVLO test 2.7 3.6 V
IVDD 7 14.2
Filterless modulation 4 7.6Quiescent Current IPVDD Classic PWM modulation 4 7.6
mA
Shutdown Current ISHDN ISHDN = IPVDD + IDD, SHDN = GND, TA = +25°C 0.5 50 µA
Filterless modulation, VMUTE = VDD
,
TA = +25°C ±2 ±12.5
Output Offset VOS Filterless modulation, VMUTE = 0V, TA = +25°C ±2 ±14 mV
MAX9768 220
Turn-On Time tON MAX9768B 15 ms
Common-Mode Bias Voltage VBIAS 1.5 V
Input Amplifier Output-
Voltage Swing High VOH Specified as
VDD - VOH RL = 2kΩ connect to 1.5V 3.6 100 mV
Input Amplifier Output-
Voltage Swing Low VOL Specified as
VOL - GND RL = 2kΩ connect to 1.5V 6 50 mV
Input Amplifier Output
Short-Circuit Current Limit ±60 mA
Input Amplifier Gain-
Bandwidth Product GBW 1.8 MHz
SPEAKER AMPLIFIERS
Internal Gain AVMAX
Max volume setting; from FB to amplifier outputs
|(OUT+) - (OUT-)|; excludes external gain
resistors
29.27 30.1 31.00 dB
MAX9768
10W Mono Class D Speaker
Amplifier with Volume Control
_______________________________________________________________________________________ 3
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
Filterless modulation 87
Efficiency (Note 2) ηPOUT = 8W, fIN =
1kHz, RL = 8ΩClassic PWM modulation 85 %
RL = 8Ω, THD+N = 1%,
filterless modulation 1.3
PVDD = 5V RL = 8Ω, THD+N = 10%,
filterless modulation 1.7
RL = 8Ω, THD+N = 10%,
classic PWM modulation 9
PVDD = 12V RL = 8Ω, THD+N = 10%,
filterless modulation 9
RL = 8Ω, THD+N = 10%,
classic PWM modulation 10
Output Power (Note 2) POUT
PVDD = 14V RL = 8Ω, THD+N = 10%,
filterless modulation 10
W
Soft Output Current Limit ILIM 1.75 2 A
Hard Output Current Limit ISC 2.5 A
Filterless modulation 0.09
Total Harmonic Distortion
Plus Noise (Note 2) THD+N f = 1kHz, RL = 8Ω,
POUT = 5W Classic PWM modulation 0.08 %
FFM 94
Unweighted SSM 93
FFM 97
0dB = 8W, RL =
8Ω, BW = 22Hz to
22kHz, filterless
modulation mode A-weighted SSM 97
FFM 93
Unweighted SSM 89
FFM 97
Signal-to-Noise Ratio
(Note 2) SNR
0dB = 8W, RL =
8Ω, BW = 22Hz to
22kHz, classic
PWM modulation A-weighted SSM 91
dB
MUTE Attenuation (Note 3) 0dB = 8W, f = 1kHz 115 dB
VDD = 2.7V to 3.6V, filterless modulation,
TA = +25°C 52 68
PVDD = 4.5V to 14V, filterless modulation,
TA = +25°C 67 84
f = 1kHz, VRIPPLE = 200mVP-P on PVDD 77
Power-Supply Rejection
Ratio PSRR
f = 1kHz, VRIPPLE = 100mVP-P on VDD 60
dB
SYNC = GND 1060 1200 1320
SYNC = unconnected 1296 1440 1584
Oscillator Frequency fOCS SYNC = VDD (spread-spectrum modulation
mode)
1200
±30
kHz
ELECTRICAL CHARACTERISTICS (continued)
(VPVDD = 12V, VDD = 3.3V, VGND = VPGND = 0, VSHDN = VDD, VMUTE = 0; Max volume setting; speaker load resistor connected
between OUT+ and OUT-, RL= , unless otherwise noted. CBIAS = 2.2µF, C1 = C2 = 0.1µF, CIN = 0.47µF, RIN = 20kΩ, RF= 30kΩ,
SSM mode. Filterless modulation mode (see the
Functional Diagram/Typical Application Circuit
). TA= TMIN to TMAX, unless otherwise
noted. Typical values are at TA= +25°C.) (Note 1)
MAX9768
10W Mono Class D Speaker
Amplifier with Volume Control
4 _______________________________________________________________________________________
ELECTRICAL CHARACTERISTICS (continued)
(VPVDD = 12V, VDD = 3.3V, VGND = VPGND = 0, VSHDN = VDD, VMUTE = 0; Max volume setting; speaker load resistor connected
between OUT+ and OUT-, RL= , unless otherwise noted. CBIAS = 2.2µF, C1 = C2 = 0.1µF, CIN = 0.47µF, RIN = 20kΩ, RF= 30kΩ,
SSM mode. Filterless modulation mode (see the
Functional Diagram/Typical Application Circuit
). TA= TMIN to TMAX, unless otherwise
noted. Typical values are at TA= +25°C.) (Note 1)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
SYNC = GND 265 300 330
SYNC = unconnected 324 360 396
Class D Switching
Frequency SYNC = VDD (spread-spectrum modulation
mode)
300
±7.5
kHz
SYNC Frequency Lock
Range 1000 1600 kHz
Minimum SYNC Frequency
Lock Duty Cycle 40 %
Maximum SYNC Frequency
Lock Duty Cycle 60 %
Gain Matching Full volume (ideal matching for RIN and RF)2%
Into shutdown 52.6
Out of shutdown 48
Into mute 67
Click-and-Pop Level (Note 2) KCP
Peak voltage, 32 samples
per second, A-weighted, RIN
x CIN 10ms to guarantee
clickless/popless operation Out of mute 57
dBV
Input Impedance DC volume control mode (SDA/VOL) 100 MΩ
Input Hysteresis DC volume control mode (SDA/VOL) 11 mV
9.5dB Gain Voltage DC volume control mode (SDA/VOL) 0.1 x VDD V
Full Mute Voltage DC volume control mode (SDA/VOL) 0.9 x VDD V
DIGITAL INPUTS (SHDN, MUTE, ADDR1, ADDR2, SYNC)
SYNC 2.33
Input-Voltage High VIH All other pins 0.7 x VDD
V
SYNC 0.8
Input-Voltage Low VIL All other pins 0.3 x VDD
V
ISYNC TA = +25°C ±7.5 ±13
Input Leakage Current ILK All other digital inputs, TA = +25°C ±1 µA
DIGITAL OUTPUT (SYNCOUT)
Output-Voltage High Load = 1mA VDD - 0.3 V
Output-Voltage Low Load = 1mA 0.3 V
Rise/Fall Time CL = 10pF 5 ns
MAX9768
10W Mono Class D Speaker
Amplifier with Volume Control
_______________________________________________________________________________________ 5
ELECTRICAL CHARACTERISTICS (continued)
(VPVDD = 12V, VDD = 3.3V, VGND = VPGND = 0, VSHDN = VDD, VMUTE = 0; Max volume setting; speaker load resistor connected
between OUT+ and OUT-, RL= , unless otherwise noted. CBIAS = 2.2µF, C1 = C2 = 0.1µF, CIN = 0.47µF, RIN = 20kΩ, RF= 30kΩ,
SSM mode. Filterless modulation mode (see the
Functional Diagram/Typical Application Circuit
). TA= TMIN to TMAX, unless otherwise
noted. Typical values are at TA= +25°C.) (Note 1)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
THERMAL PROTECTION
Thermal Shutdown
Threshold 150 °C
Thermal Shutdown
Hysteresis 15 °C
DIGITAL INPUTS (SCLK, SDA/VOL)
Input-Voltage High VIH 0.7 x VDD V
Input-Voltage Low VIL 0.3 x VDD V
Input High Leakage Current IIH VIN = VDD, TA = +25°C ±1 µA
Input Low Leakage Current IIL VIN = GND, TA = +25°C ±1 µA
Input Hysteresis 0.1 x VDD V
Input Capacitance CIN 5pF
DIGITAL OUTPUTS (SDA/VOL)
Output High Current IOH VOH = VDD A
Output Low Voltage VOL IOL = 3mA 0.4 V
I2C TIMING CHARACTERISTICS (Figure 3)
Serial Clock fSCL 400 kHz
Bus Free Time Between a
STOP and START
Condition
tBUF 1.3 µs
Hold Time (Repeated)
START Condition tHD
,
STA 0.6 µs
Repeated START Condition
Setup Time tSU
,
STA 0.6 µs
STOP Condition Setup Time tSU
,
STO 0.6 µs
Data Hold Time tHD
,
DAT 0 0.9 µs
Data Setup Time tSU
,
DAT 100 ns
SCL Clock Low Period tLOW 1.3 µs
SCL Clock High Period tHIGH 0.6 µs
Rise Time of SDA and SCL,
Receiving tR(Note 4) 20 +
0.1Cb 300 ns
Fall Time of SDA and SCL,
Receiving tF(Note 4) 20 +
0.1Cb 300 ns
MAX9768
10W Mono Class D Speaker
Amplifier with Volume Control
6 _______________________________________________________________________________________
Note 1: All devices are 100% production tested at TA= +25°C. All temperature limits are guaranteed by design.
Note 2: Testing performed with a resistive load in series with an inductor to simulate an actual speaker load. For RL= 8Ω, L = 68µH.
Note 3: Device muted by either asserting MUTE or minimum VOL setting.
Note 4: Cb= total capacitance of one bus line in pF.
ELECTRICAL CHARACTERISTICS (continued)
(VPVDD = 12V, VDD = 3.3V, VGND = VPGND = 0, VSHDN = VDD, VMUTE = 0; Max volume setting; speaker load resistor connected
between OUT+ and OUT-, RL= , unless otherwise noted. CBIAS = 2.2µF, C1 = C2 = 0.1µF, CIN = 0.47µF, RIN = 20kΩ, RF= 30kΩ,
SSM mode. Filterless modulation mode (see the
Functional Diagram/Typical Application Circuit
). TA= TMIN to TMAX, unless otherwise
noted. Typical values are at TA= +25°C.) (Note 1)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
Fall Time of SDA,
Transmitting tF(Note 4) 20 +
0.1Cb 250 ns
Pulse Width of Spike
Suppressed tSP 050ns
Capacitive Load for Each
Bus Line Cb400 pF
TOTAL HARMONIC DISTORTION
PLUS NOISE vs. FREQUENCY
MAX9768 toc01
FREQUENCY (Hz)
THD+N (%)
10k1k100
0.1
1
10
0.01
10 100k
PVDD = 12V
RL = 8Ω
FILTERLESS MODULATION
OUTPUT POWER = 6W
OUTPUT POWER = 2W
TOTAL HARMONIC DISTORTION
PLUS NOISE vs. FREQUENCY
MAX9768 toc02
FREQUENCY (Hz)
THD+N (%)
10k1k100
0.1
1
10
0.01
10 100k
PVDD = 12V
RL = 8Ω
PWM MODE
OUTPUT POWER = 5W
OUTPUT POWER = 2W
TOTAL HARMONIC DISTORTION
PLUS NOISE vs. FREQUENCY
MAX9768 toc03
FREQUENCY (Hz)
THD+N (%)
10k1k100
0.1
0.01
1
10
0.001
10 100k
PVDD = 5V
RL = 8Ω
FILTERLESS MODULATION
OUTPUT POWER = 1W
OUTPUT POWER = 300mW
Typical Operating Characteristics
(VPVDD = 12V, VDD = 3.3V, VGND = VPGND = 0, VMUTE = 0; 0dB volume setting; all speaker load resistors connected between OUT+
and OUT-, RL= 8Ω, unless otherwise noted. CBIAS = 2.2µF, C1 = C2 = 0.1µF, CIN = 0.47µF, RIN = 20kΩ, RFB = 30kΩ, spread-spec-
trum modulation mode.)
MAX9768
10W Mono Class D Speaker
Amplifier with Volume Control
_______________________________________________________________________________________
7
TOTAL HARMONIC DISTORTION
PLUS NOISE vs. FREQUENCY
MAX9768 toc04
FREQUENCY (Hz)
THD+N (%)
10k1k100
0.1
0.01
1
10
0.001
10 100k
PVDD = 5V
RL = 8Ω
PWM MODE
OUTPUT POWER = 300mW
OUTPUT POWER = 800mW
TOTAL HARMONIC DISTORTION
PLUS NOISE vs. FREQUENCY
MAX9768 toc05
FREQUENCY (Hz)
THD+N (%)
0.1
0.01
1
10
0.001
PVDD = 12V
RL = 8Ω
FILTERLESS MODULATION
POUT = 4W
10k1k10010 100k
FIXED-FREQUENCY
MODULATION
SPREAD-SPECTRUM
MODULATION
MAX9768 toc06
FREQUENCY (Hz)
THD+N (%)
0.1
0.01
1
10
0.001
PVDD = 12V
RL = 8Ω
PWM MODE
POUT = 4W
TOTAL HARMONIC DISTORTION
PLUS NOISE vs. FREQUENCY
10k1k10010 100k
FIXED-FREQUENCY
MODULATION
SPREAD-SPECTRUM
MODULATION
TOTAL HARMONIC DISTORTION
PLUS NOISE vs. OUTPUT POWER
MAX9768 toc07
OUTPUT POWER (W)
THD+N (%)
108462
0.1
0.01
1
100
10
0.001
012
PVDD = 12V
RL = 8Ω
FILTERLESS MODULATION
fIN = 10kHz
fIN = 100Hz fIN = 1kHz
TOTAL HARMONIC DISTORTION
PLUS NOISE vs. OUTPUT POWER
MAX9768 toc08
OUTPUT POWER (W)
THD+N (%)
108462
0.1
0.01
1
100
10
0.001
0
PVDD = 12V
RL = 8Ω
PWM MODE
fIN = 10kHz
fIN = 100Hz fIN = 1kHz
TOTAL HARMONIC DISTORTION
PLUS NOISE vs. OUTPUT POWER
MAX9768 toc09
OUTPUT POWER (W)
THD+N (%)
2.01.0 1.50.5
0.1
0.01
1
100
10
0.001
0
PVDD = 5V
RL = 8Ω
FILTERLESS MODULATION
fIN = 10kHz
fIN = 100Hz fIN = 1kHz
TOTAL HARMONIC DISTORTION
PLUS NOISE vs. OUTPUT POWER
MAX9768 toc10
OUTPUT POWER (W)
THD+N (%)
2.00.8 1.2 1.60.4
0.1
0.01
1
100
10
0.001
0
PVDD = 5V
RL = 8Ω
PWM MODE
fIN = 10kHz
fIN = 100Hz fIN = 1kHz
TOTAL HARMONIC DISTORTION
PLUS NOISE vs. OUTPUT POWER
MAX9768 toc11
OUTPUT POWER (W)
THD+N (%)
104682
0.1
1
100
10
0.01
0
PVDD = 12V
RL = 8Ω
fIN = 1kHz
FILTERLESS MODULATION
FIXED-FREQUENCY
MODULATION
SPREAD-SPECTRUM
MODULATION
TOTAL HARMONIC DISTORTION
PLUS NOISE vs. OUTPUT POWER
MAX9768 toc12
OUTPUT POWER (W)
THD+N (%)
104682
0.1
1
100
10
0.01
0
PVDD = 12V
RL = 8Ω
fIN = 1kHz
PWM MODE
FIXED-FREQUENCY
MODULATION
SPREAD-SPECTRUM
MODULATION
Typical Operating Characteristics (continued)
(VPVDD = 12V, VDD = 3.3V, VGND = VPGND = 0, VMUTE = 0; 0dB volume setting; all speaker load resistors connected between OUT+
and OUT-, RL= 8Ω, unless otherwise noted. CBIAS = 2.2µF, C1 = C2 = 0.1µF, CIN = 0.47µF, RIN = 20kΩ, RFB = 30kΩ, spread-spec-
trum modulation mode.)
MAX9768
10W Mono Class D Speaker
Amplifier with Volume Control
8 _______________________________________________________________________________________
EFFICIENCY vs. OUTPUT POWER
MAX9768 toc13
OUTPUT POWER (W)
EFFICIENCY (%)
104682
20
10
30
50
40
60
100
80
70
90
0
0
PWM MODE
PVDD = 12V
fIN = 1kHz
RL = 8Ω
FILTERLESS MODULATION
EFFICIENCY vs. OUTPUT POWER
MAX9768 toc14
OUTPUT POWER (W)
EFFICIENCY (%)
2.01.0 1.50.5
20
10
30
50
40
60
100
80
70
90
0
0
PWM MODE
FILTERLESS MODULATION
PVDD = 5V
fIN = 1kHz
RL = 8Ω
EFFICIENCY vs. SUPPLY VOLTAGE
MAX9768 toc15
SUPPLY VOLTAGE (V)
EFFICIENCY (%)
14.58.5 10.5 12.56.5
83
86
89
95
92
80
4.5
THD+N = 10%
THD+N = 1%
fIN = 1kHz
RL = 8Ω
FILTERLESS MODULATION
EFFICIENCY vs. SUPPLY VOLTAGE
MAX9768 toc16
SUPPLY VOLTAGE (V)
EFFICIENCY (%)
14.58.5 10.5 12.56.5
83
86
89
95
92
80
4.5
fIN = 1kHz
RL = 8Ω
PWM MODULATION
THD+N = 10%
THD+N = 1%
OUTPUT POWER vs. SUPPLY VOLTAGE
MAX9768 toc17
SUPPLY VOLTAGE (V)
OUTPUT POWER (W)
14810126
2
4
6
8
14
12
10
0
4
RL = 8Ω
fIN = 1kHz
PWM MODE
THD+N = 10%
THD+N = 1%
OUTPUT POWER vs. SUPPLY VOLTAGE
MAX9768 toc18
SUPPLY VOLTAGE (V)
OUTPUT POWER (W)
14810126
2
4
6
8
12
10
0
4
RL = 4Ω
fIN = 1kHz
PWM MODE
THD+N = 1%
THD+N = 10%
OUTPUT POWER vs. LOAD RESISTANCE
MAX9768 toc19
LOAD RESISTANCE (Ω)
OUTPUT POWER (W)
3010 15 25205
2
4
6
8
12
10
0
0
PVDD = 12V
f = 1kHz
PWM MODE
THD+N = 1%
THD+N = 10%
OUTPUT POWER vs. LOAD RESISTANCE
MAX9768 toc20
LOAD RESISTANCE (Ω)
OUTPUT POWER (W)
3010 15 25205
0.5
1.0
1.5
2.5
2.0
3.5
3.0
0
0
PVDD = 5V
f = 1kHz
PWM MODE
THD+N = 1%
THD+N = 10%
Typical Operating Characteristics (continued)
(VPVDD = 12V, VDD = 3.3V, VGND = VPGND = 0, VMUTE = 0; 0dB volume setting; all speaker load resistors connected between OUT+
and OUT-, RL= 8Ω, unless otherwise noted. CBIAS = 2.2µF, C1 = C2 = 0.1µF, CIN = 0.47µF, RIN = 20kΩ, RFB = 30kΩ, spread-spec-
trum modulation mode.)
CASE TEMPERATURE vs. OUTPUT POWER
MAX9768 toc21
OUTPUT POWER (W)
CASE TEMPERATURE (°C)
1246 1082
10
30
20
40
50
70
60
90
80
0
0
fIN = 1kHz
RL = 8Ω
PVDD = 14V
PVDD = 12V
MAX9768
10W Mono Class D Speaker
Amplifier with Volume Control
_______________________________________________________________________________________
9
POWER-SUPPLY REJECTION RATIO (PVDD)
vs. FREQUENCY
MAX9768 toc22
FREQUENCY (Hz)
PSRR (dB)
100k1k 10k100
-90
-70
-80
-60
-50
-30
-40
0
-10
-20
-100
10
PVDD = 12V
VRIPPLE = 100mVP-P
RL = 8Ω
PWM MODE
FILTERLESS MODULATION
POWER-SUPPLY REJECTION RATIO (VDD)
vs. FREQUENCY
MAX9768 toc23
FREQUENCY (Hz)
PSRR (dB)
100k1k 10k100
-90
-70
-80
-60
-50
-30
-40
0
-10
-20
-100
10
VDD = 3.3V
VRIPPLE = 100mVP-P
RL = 8Ω
PWM MODE
FILTERLESS MODULATION
OUTPUT WAVEFORM
(FILTERLESS MODULATION)
MAX9768 toc24
1μs/div
5V/div
5V/div
OUTPUT WAVEFORM (PWM MODE)
MAX9768 toc25
1μs/div
5V/div
5V/div
OUTPUT FREQUENCY SPECTRUM
MAX9768 toc26
FREQUENCY (kHz)
2010515
-120
-100
-80
-40
-60
0
-20
-140
0
FFM MODE
VIN = -60dBV
f = 1kHz
RL = 8Ω
UNWEIGHTED
OUTPUT MAGNITUDE (dBV)
OUTPUT FREQUENCY SPECTRUM
MAX9768 toc27
FREQUENCY (kHz)
2010515
-120
-100
-80
-40
-60
0
-20
-140
0
VIN = -60dBV
f = 1kHz
RL = 8Ω
UNWEIGHTED
OUTPUT MAGNITUDE (dBV)
WIDEBAND OUTPUT SPECTRUM
(FIXED-FREQUENCY MODULATION MODE)
MAX9768 toc28
FREQUENCY (MHz)
100010 100
-90
-100
-80
-70
-30
-40
-50
-60
0
-10
-20
1
RBW = 10kHz
INPUT AC GROUNDED
FILTERLESS MODULATION
OUTPUT AMPLITUDE (dBV)
WIDEBAND OUTPUT SPECTRUM
(FIXED-FREQUENCY MODULATION MODE)
MAX9768 toc29
FREQUENCY (MHz)
100010 100
-90
-100
-80
-70
-30
-40
-50
-60
0
-10
-20
1
RBW = 10kHz
INPUT AC GROUNDED
PWM MODE
OUTPUT AMPLITUDE (dBV)
WIDEBAND OUTPUT SPECTRUM
(SPREAD-SPECTRUM MODULATION MODE)
MAX9768 toc30
FREQUENCY (MHz)
100010 100
-90
-100
-80
-70
-30
-40
-50
-60
0
-10
-20
1
OUTPUT AMPLITUDE (dBV)
RBW = 10kHz
INPUT AC GROUNDED
FILTERLESS MODULATION
_______________________________________________________________________________________
9
Typical Operating Characteristics (continued)
(VPVDD = 12V, VDD = 3.3V, VGND = VPGND = 0, VMUTE = 0; 0dB volume setting; all speaker load resistors connected between OUT+
and OUT-, RL= 8Ω, unless otherwise noted. CBIAS = 2.2µF, C1 = C2 = 0.1µF, CIN = 0.47µF, RIN = 20kΩ, RFB = 30kΩ, spread-spec-
trum modulation mode.)
MAX9768
10W Mono Class D Speaker
Amplifier with Volume Control
10 ______________________________________________________________________________________
WIDEBAND OUTPUT SPECTRUM
(SPREAD-SPECTRUM MODULATION MODE)
MAX9768 toc31
FREQUENCY (MHz)
100010 100
-90
-100
-80
-70
-30
-40
-50
-60
0
-10
-20
1
OUTPUT AMPLITUDE (dBV)
RBW = 10kHz
INPUT AC GROUNDED
PWM MODE
TURN-ON/OFF RESPONSE
(MAX9768)
MAX9768 toc32
100ms/div
SHDN
2V/div
OUT
500mA/div
TURN-ON/OFF RESPONSE
(MAX9768B)
MAX9768 toc33
40ms/div
SHDN
2V/div
OUT
500mA/div
VOLUME CONTROL LEVEL
vs. VOLUME CONTROL VOLTAGE
MAX9768 toc34
VVOL (V)
3.52.01.51.00.5 3.02.5
-100
-80
-60
-20
-40
20
0
-120
0
VOLUME LEVEL (dB)
SUPPLY CURRENT (PVDD)
vs. SUPPLY VOLTAGE
MAX9768 toc35
SUPPLY VOLTAGE (V)
14108612
0.5
1.0
1.5
3.0
2.0
2.5
4.0
3.5
0
4
SUPPLY CURRENT (mA)
PWM MODE
RL =
FILTERLESS MODULATION
SUPPLY CURRENT (VDD)
vs. SUPPLY VOLTAGE
MAX9768 toc36
SUPPLY VOLTAGE (V)
3.63.23.02.8 3.4
7
9
13
11
15
5
2.6
SUPPLY CURRENT (mA)
PWM MODE
FILTERLESS MODULATION
SHUTDOWN CURRENT
vs. SUPPLY VOLTAGE
MAX9768 toc37
SUPPLY VOLTAGE (V)
14108612
0.35
0.45
0.40
0.50
0.30
4
SHUTDOWN CURRENT (μA)
SHUTDOWN CURRENT = IPVDD + IDD
VDD = 3.3V
Typical Operating Characteristics (continued)
(VPVDD = 12V, VDD = 3.3V, VGND = VPGND = 0, VMUTE = 0; 0dB volume setting; all speaker load resistors connected between OUT+
and OUT-, RL= 8Ω, unless otherwise noted. CBIAS = 2.2µF, C1 = C2 = 0.1µF, CIN = 0.47µF, RIN = 20kΩ, RFB = 30kΩ, spread-spec-
trum modulation mode.)
MAX9768
10W Mono Class D Speaker
Amplifier with Volume Control
______________________________________________________________________________________ 11
Pin Description
PIN NAME FUNCTION
1, 2 OUT+ Positive Speaker Output
3, 16 PVDD Speaker Amplifier Power-Supply Input. Bypass with a 1µF capacitor to ground.
4 BOOT+ Positive Speaker Output Boost Flying-Capacitor Connection. Connect a 0.1µF ceramic capacitor
between BOOT+ and OUT+.
5 SCLK
I2C Serial-Clock Input and Modulation Scheme Select. In I2C mode (ADDR1 and ADDR2 GND)
acts as I2C serial-clock input. Connect SCLK to VDD for classic PWM modulation, or connect
SCLK to ground for filterless modulation.
6 SDA/VOL I2C Serial Data I/O and Analog Volume Control Input
7FB
Feedback. Connect feedback resistor between FB and IN to set amplifier gain. See the Adjustable
Gain section.
8 IN Audio Input
9, 11 GND Ground
10 BIAS Common-Mode Bias Voltage. Bypass with a 2.2µF capacitor to GND.
12 SYNC
Frequency Select and External Clock Input.
SYNC = GND: Fixed-frequency mode with fS = 300kHz.
SYNC = Unconnected: Fixed-frequency mode with fS = 360kHz.
SYNC = VDD: Spread-spectrum mode with fS = 300kHz ±7.5kHz.
SYNC = Clocked: Fixed-frequency mode with fS = external clock frequency.
13 SYNCOUT Clock Signal Output
14 VDD Power-Supply Input. Bypass with a 1µF capacitor to GND.
15 BOOT- Negative Speaker Output Boost Flying-Capacitor Connection. Connect a 0.1µF ceramic capacitor
between BOOTL- and OUTL-.
17, 18 OUT- Negative Speaker Output
19 SHDN Shutdown Input. Drive SHDN low to disable the audio amplifiers. Connect SHDN to VDD for normal
operation
20 MUTE Mute Input. Drive MUTE high to mute the speaker outputs. Connect MUTE to GND for normal
operation.
21, 22 PGND Power Ground
23 ADDR2 Address Select Input 2. I2C address option, also selects volume control mode.
24 ADDR1 Address Select Input 1. I2C address option, also selects volume control mode.
—EP
Exposed Pad. Connect the exposed thermal pad to GND, and use multiple vias to a solid copper
area on the bottom of the PCB.
Detailed Description
The MAX9768 10W, Class D audio power amplifier with
spread-spectrum modulation provides a significant step
forward in switch-mode amplifier technology. The
MAX9768 offers Class AB performance with Class D
efficiency and a minimal board space solution. This
device features a wide supply voltage operation (4.5V to
14V), analog or digitally adjusted volume control, exter-
nally set input gain, shutdown mode, SYNC input and
output, speaker mute, and industry-leading click-and-
pop suppression.
The MAX9768 features a 64-step, dual-mode (analog or
I2C programmed) volume control and mute function. In
analog volume control mode, voltage applied to
SDA/VOL sets the volume level. Two address inputs
(ADDR1, ADDR2) set the volume control function
between analog and I2C and set the slave address. In
I2C mode there are three selectable slave addresses
allowing for multiple devices on a single bus.
Spread-spectrum modulation and synchronizable
switching frequency significantly reduce EMI emis-
sions. The outputs use Maxim’s low-EMI modulation
scheme with minimum pulse outputs when the audio
inputs are at the zero crossing. As the input voltage
increases or decreases, the duration of the pulse at
one output increases while the other output pulse dura-
tion remains the same. This causes the net voltage
across the speaker (VOUT+ - VOUT-) to change. The
minimum-width pulse topology reduces EMI and
increases efficiency.
MAX9768
10W Mono Class D Speaker
Amplifier with Volume Control
12 ______________________________________________________________________________________
MUTE
VOLUME
CONTROL
CLASS D
SHUTDOWN
CONTROL
OSCILLATOR
SYNCOUT
BIAS
14
VDD
VDD
PVDD
CBIAS
2.2μF
7
81, 2
4
17, 18
15
10
13
FB
RF
30kΩ
RIN
20kΩ
CIN
0.47μFC1
0.1μF
C2
0.1μF
1μF1μF
IN
20
19
6
5
24
23
GND PGND
OUT+
BOOT+
OUT-
BOOT-
BIAS
12
3, 16
9, 11 21, 22
2.7V to 3.6V 4.5V to 14V
SYNC
MUTE
SHDN
SDA/VOL
SCLK
ADDR1
ADDR2
I2C
ANALOG
CONTROL
MAX9768
(SHOWN IN ANALOG VOLUME CONTOL MODE, AV = 23.5dB, f-3dB = 17Hz, SPREAD-SPECTRUM MODULATION MODE, FILTERLESS MODULATION MODE, MUTE OFF)
Functional Diagram/Typical Application Circuit
Operating Modes
Fixed-Frequency Mode
The MAX9768 features two fixed-frequency modes:
300kHz and 360kHz. Connect SYNC to GND to select
300kHz switching frequency; leave SYNC unconnected
to select 360kHz switching frequency. The frequency
spectrum of the MAX9768 consists of the fundamental
switching frequency and its associated harmonics (see
the Wideband Output Spectrum graphs in the
Typical
Operating Characteristics
). For applications where
exact spectrum placement of the switching fundamen-
tal is important, program the switching frequency so the
harmonics do not fall within a sensitive frequency band
(Table 1). Audio reproduction is not affected by chang-
ing the switching frequency.
Spread-Spectrum Mode
The MAX9768 features a unique spread-spectrum
mode that flattens the wideband spectral components,
improving EMI emissions that may be radiated by the
speaker and cables. This mode is enabled by setting
SYNC = VDD (Table 1). In SSM mode, the switching fre-
quency varies randomly by ±7.5kHz around the center
frequency (300kHz). The modulation scheme remains
the same, but the period of the triangle waveform
changes from cycle to cycle. Instead of a large amount
of spectral energy present at multiples of the switching
frequency, the energy is now spread over a bandwidth
that increases with frequency. Above a few megahertz,
the wideband spectrum looks like white noise for EMI
purposes. A proprietary amplifier topology ensures this
does not corrupt the noise floor in the audio bandwidth.
External Clock Mode
The SYNC input allows the MAX9768 to be synchro-
nized to an external clock, or another Maxim Class D
amplifier, creating a fully synchronous system, minimiz-
ing clock intermodulation, and allocating spectral com-
ponents of the switching harmonics to insensitive
frequency bands. Applying a clock signal between
1MHz and 1.6MHz to SYNC synchronizes the
MAX9768. The Class D switching frequency is equal to
one-fourth the SYNC input frequency.
SYNCOUT is equal to the SYNC input frequency and
allows several Maxim amplifiers to be cascaded. The
synchronized output minimizes interference due to
clock intermodulation caused by the switching spread
between single devices. The modulation scheme
remains the same when using SYNCOUT, and audio
reproduction is not affected (Figure 1). Current flowing
between SYNCOUT of a master device and SYNC of a
slave device is low as the SYNC input is high imped-
ance (typically 200kΩ).
MAX9768
10W Mono Class D Speaker
Amplifier with Volume Control
______________________________________________________________________________________ 13
Table 1. Operating Modes
SYNC OSCILLATOR FREQUENCY (kHz) CLASS D FREQUENCY (kHz)
GND Fixed-frequency modulation with fOSC = 1200 Fixed-frequency modulation with fOSC = 300
Unconnected
Fixed-frequency modulation with fOSC = 1440 Fixed-frequency modulation with fOSC = 360
VDD Spread-spectrum modulation with fOSC = 1200 ±30 Spread-spectrum modulation with fOSC = 300 ±7.5
Clocked Fixed-frequency modulation with fOSC = external clock
frequency
Fixed-frequency modulation with fOSC = external clock
frequency / 4
Figure 1. Cascading Two Amplifiers
Filterless Modulation/PWM Modulation
The MAX9768 features two output modulation
schemes: filterless modulation or classic PWM, selec-
table through SCLK when the device is in analog mode
(ADDR2 and ADDR1 = GND, Table 2) or through the
I2C interface (Table 7). Maxim’s unique, filterless modu-
lation scheme eliminates the LC filter required by tradi-
tional Class D amplifiers, reducing component count,
conserving board space and system cost. Although the
MAX9768 meets FCC and other EMI limits with a low-
cost ferrite bead filter, many applications still may want
to use a full LC-filtered output. If using a full LC filter,
the performance is best with the MAX9768 configured
for classic PWM output.
Switching between schemes while in normal operating
mode with the I2C interface, the output is not click-and-
pop protected. To have click-and-pop protection when
switching between output schemes, the device must
enter shutdown mode and be configured to the new out-
put scheme before the startup sequence is terminated.
The startup time for the MAX9768 is typically 220ms.
The startup time for the MAX9768B is typically 15ms.
Efficiency
Efficiency of a Class D amplifier is due to the switching
operation of the output stage transistors. In a Class D
amplifier, the output transistors act as current-steering
switches and consume negligible additional power.
Any power loss associated with the Class D output
stage is mostly due to the I2R loss of the MOSFET on-
resistance, and quiescent-current overhead.
The theoretical best efficiency of a linear amplifier is
78%, however, that efficiency is only exhibited at peak
output power. Under normal operating levels (typical
music reproduction levels), efficiency falls below 30%,
whereas the MAX9768 still exhibits > 80% efficiencies
under the same conditions (Figure 2).
Soft Current Limit
When the output current exceeds the soft current limit,
2A (typ), the MAX9768 enters a cycle-by-cycle current-
limit mode. In soft current-limit mode, the output is
clipped at 2A. When the output decreases so the out-
put current falls below 2A, normal operation resumes.
The effect of soft current limiting is a slight increase in
distortion. Most applications will not enter soft current-
limit mode unless the speaker or filter creates imped-
ance nulls below 8Ω.
MAX9768
10W Mono Class D Speaker
Amplifier with Volume Control
14 ______________________________________________________________________________________
Table 2. Modulation Scheme Selection In Analog Mode
ADDR2 ADDR1 SDA/VOL SCLK FUNCTION
0 0 Analog Volume Control 0 Filterless Modulation
0 0 Analog Volume Control 1 Classic PWM (50% Duty Cycle)
EFFICIENCY vs. OUTPUT POWER
MAX9768 fig02
OUTPUT POWER (W)
EFFICIENCY (%)
8642
10
20
30
40
50
60
70
80
90
100
0
010
MAX9768
CLASS AB
PVDD = 12V
fIN = 1kHz
RL = 8Ω
Figure 2. MAX9768 Efficiency vs. Class AB Efficiency
MAX9768
10W Mono Class D Speaker
Amplifier with Volume Control
______________________________________________________________________________________ 15
Hard Current Limit
When the output current exceeds the hard current limit,
2.5A (typ), the MAX9768 disables the outputs and initi-
ates a startup sequence. This startup sequence takes
220ms for the MAX9768 and 15ms for the MAX9768B.
The shutdown and startup sequence is repeated until
the output fault is removed. When in hard current limit,
the output may make a soft clicking sound. The aver-
age supply current is relatively low, as the duty cycle of
the output short is brief. Most applications will not enter
hard current-limit mode unless the output is short cir-
cuited or incorrectly connected.
Thermal Shutdown
When the die temperature exceeds the thermal shut-
down threshold, +150°C (typ), the MAX9768 outputs
are disabled. When the die temperature decreases
below +135°C (typ), normal operation resumes. The
effect of thermal shutdown is an output signal turning
off for approximately 3s in most applications, depend-
ing on the thermal time constant of the audio system.
Most applications should never enter thermal shut-
down. Some of the possible causes of thermal shut-
down are too low of a load impedance, high ambient
temperature, poor PCB layout and assembly, or exces-
sive output overdrive.
Shutdown
The MAX9768 features a shutdown mode that reduces
power consumption and extends battery life. Driving
SHDN low places the device in low-power (0.5µA) shut-
down mode. Connect SHDN to digital high for normal
operation. In shutdown mode, the outputs are high
impedance, SYNCOUT is pulled high, the BIAS voltage
decays to zero, and the common-mode input voltage
decays to zero. The I2C register retains its contents
during shutdown.
Undervoltage Lockout (UVLO)
The MAX9768 features an undervoltage lockout protec-
tion that shuts down the device if either of the supplies
are too low. The device will go into shutdown if VDD is
less than 2.5V (VDD UVLO = 2.5V) or if PVDD is less
than 4V (PVDD UVLO = 4V).
Mute Function
The MAX9768 features a clickless/popless mute mode.
When the device is muted, the outputs do not stop
switching, only the volume level is muted to the speak-
er. To mute the MAX9768, drive MUTE to logic-high.
MUTE should be held high during system power-up
and power-down to ensure optimum click-and-pop
performance.
Volume Control
The volume control operates from either an analog volt-
age input or through the I2C interface. The volume con-
trol has 64 levels, with the lowest setting equal to mute.
To set the device to analog mode, connect ADDR1 and
ADDR2 to GND. In analog mode, SDA/VOL is an ana-
log input for volume control, see the
Functional
Diagram/Typical Application Circuit
. The analog input
range is ratiometric between 0.9 x VDD and 0.1 x VDD,
where 0.9 x VDD = full mute and 0.1 x VDD = full volume
(Table 6).
In I2C mode, volume control for the speaker is controlled
separately by the command register (Tables 4, 5, 6). See
the
Write Data Format
section for more information
regarding formatting data and tables to set volume levels.
I2C Interface
The MAX9768 features an I2C 2-wire serial interface
consisting of a serial data line (SDA) and a serial clock
line (SCL). SDA and SCL facilitate communication
between the MAX9768 and the master at clock rates up
to 400kHz. When the MAX9768 is used on an I2C bus
with multiple devices, the VDD supply must stay pow-
ered on to ensure proper I2C bus operation. The mas-
ter, typically a microcontroller, generates SCL and
initiates data transfer on the bus. Figure 3 shows the 2-
wire interface timing diagram.
A master device communicates to the MAX9768 by trans-
mitting the proper address followed by the data word.
Each transmit sequence is framed by a START (S) or
REPEATED START (Sr) condition and a STOP (P) condi-
tion. Each word transmitted over the bus is 8 bits long
and is always followed by an acknowledge clock pulse.
The MAX9768 SDA line operates as both an input and
an open-drain output. A pullup resistor, greater than
500Ω, is required on the SDA bus. The MAX9768 SCL
line operates as an input only. A pullup resistor, greater
than 500Ω, is required on SCL if there are multiple mas-
ters on the bus, or if the master in a single-master sys-
tem has an open-drain SCL output. Series resistors in
line with SDA and SCL are optional. The SCL and SDA
inputs suppress noise spikes to assure proper device
operation even on a noisy bus.
MAX9768
10W Mono Class D Speaker
Amplifier with Volume Control
16 ______________________________________________________________________________________
Bit Transfer
One data bit is transferred during each SCL cycle. The
data on SDA must remain stable during the high period
of the SCL pulse. Changes in SDA while SCL is high
are control signals (see the
START and STOP
Conditions
section). SDA and SCL idle high when the
I2C bus is not busy.
START and STOP Conditions
A master device initiates communication by issuing a
START condition. A START condition is a high-to-low
transition on SDA with SCL high. A STOP condition is a
low-to-high transition on SDA while SCL is high (Figure 4).
A START (S) condition from the master signals the
beginning of a transmission to the MAX9768. The mas-
ter terminates transmission, and frees the bus, by issu-
ing a STOP (P) condition. The bus remains active if a
REPEATED START (Sr) condition is generated instead
of a STOP condition.
Early STOP Conditions
The MAX9768 recognizes a STOP condition at any point
during data transmission except if the STOP condition
occurs in the same high pulse as a START condition.
Slave Address
The slave address of the MAX9768 is 8 bits and con-
sisting of 3 fields: the first field is 5 bits wide and is
fixed (10010). The second is a 2-bit field, which is set
through ADDR2 and ADDR1 (externally connected as
logic-high or low). Third field is a R/Wflag bit. Set R/W
= 0 to write to the slave. A representation of the slave
address is shown in Table 3.
When ADDR1 and ADDR2 are connected to GND, seri-
al interface communication is disabled. Table 4 sum-
marizes the slave address of the device as a function of
ADDR1 and ADDR2.
Acknowledge
The acknowledge bit (ACK) is a clocked 9th bit that the
MAX9768 uses to handshake receipt each byte of data
(Figure 5). The MAX9768 pulls down SDA during the
master-generated 9th clock pulse. The SDA line must
remain stable and low during the high period of the
acknowledge clock pulse. Monitoring ACK allows for
detection of unsuccessful data transfers. An unsuc-
cessful data transfer occurs if a receiving device is
busy or if a system fault has occurred. In the event of
an unsuccessful data transfer, the bus master can re-
attempt communication.
SCL
SDA
START
CONDITION
STOP
CONDITION
REPEATED
START
CONDITION
START
CONDITION
tHD,STA
tSU,STA tHD,STA tSP
tBUF
tSU,STO
tLOW
tSU,DAT
tHD,DAT
tHIGH
tRtF
Figure 3. 2-Wire Serial-Interface Timing Diagram
SCL
SDA
SSrP
Figure 4. START, STOP, and REPEATED START Conditions
Write Data Format
A write to the MAX9768 includes transmission of a
START condition, the slave address with the R/Wbit set
to 0 (see Table 3), one byte of data to the command
register, and a STOP condition. Figure 6 illustrates the
proper format for one frame.
Volume Control
The command register is used to control the volume
level of the speaker amplifier. The two MSBs (D7 and
D6) should be set to 00 to choose the speaker register.
V5–V0 is the volume control data that will be written into
the addresses register to set the volume level (see
Tables 5 and 6).
For a write byte operation, the master sends a single byte
to the slave device (MAX9768). This is done as follows:
1) The master sends a start condition.
2) The master sends the 7-bit slave ID plus a write bit
(low).
3) The addressed slave asserts an ACK on the data
line.
4) The master sends 8 data bits.
5) The active slave asserts an ACK (or NACK) on the
data line.
6) The master generates a stop condition.
MAX9768
10W Mono Class D Speaker
Amplifier with Volume Control
______________________________________________________________________________________ 17
Table 3. Slave Address Block
SA7 (MSB) SA6 SA5 SA4 SA3 SA2 SA1 SA0 (LSB)
1 0 0 1 0 ADDR2 ADDR1 R/W
Table 4. Slave Address
ADDR2 ADDR1 SLAVE ADDRESS
0 0 Disabled
0 1 1001001_
1 0 1001010_
1 1 1001011_
1
SCL
START
CONDITION
SDA
289
CLOCK PULSE FOR
ACKNOWLEDGMENT
ACKNOWLEDGE
NOT ACKNOWLEDGE
Figure 5. Acknowledge
S SLAVE ADDRESS
7 bits
WRITE BYTE FORMAT
WR ACK DATA
8 bits
ACK P
DATA BYTE: GIVES A COMMAND.SLAVE ADDRESS:
EQUIVALENT TO CHIP-
SELECT LINE OF A 3-
WIRE INTERFACE.
0
Figure 6. Write Data Format Example
MAX9768
10W Mono Class D Speaker
Amplifier with Volume Control
18 ______________________________________________________________________________________
Table 5. Data Byte Format
D7
(MSB) D6 D5 D4 D3 D2 D1 D0
(LSB)
0 0 V5 V4 V3 V2 V1 V0
Table 6. Speaker Volume Levels
V5 V4 V3 V2 V1 V0 VOLUME
POSITION
VOLUME
LEVEL (dB)
STEP SIZE
(dB)
1 1 1 1 1 1 63 9.5 0.7
1 1 1 1 1 0 62 8.8 0.7
1 1 1 1 0 1 61 8.2 0.6
1 1 1 1 0 0 60 7.6 0.6
1 1 1 0 1 1 59 7.0 0.6
1 1 1 0 1 0 58 6.5 0.5
1 1 1 0 0 1 57 5.9 0.5
1 1 1 0 0 0 56 5.4 0.5
1 1 0 1 1 1 55 4.9 0.5
1 1 0 1 1 0 54 4.4 0.5
1 1 0 1 0 1 53 3.9 0.6
1 1 0 1 0 0 52 3.4 0.4
1 1 0 0 1 1 51 2.9 0.5
1 1 0 0 1 0 50 2.4 0.4
1 1 0 0 0 1 49 2.0 0.4
1 1 0 0 0 0 48 1.6 0.4
1 0 1 1 1 1 47 1.2 0.7
1 0 1 1 1 0 46 0.5 1.0
1 0 1 1 0 1 45 -0.5 1.5
1 0 1 1 0 0 44 -1.9 1.5
1 0 1 0 1 1 43 -3.4 1.5
1 0 1 0 1 0 42 -5.0 1.1
1 0 1 0 0 1 41 -6.0 1.1
1 0 1 0 0 0 40 -7.1 1.8
1 0 0 1 1 1 39 -8.9 1.0
1 0 0 1 1 0 38 -9.9 1.0
1 0 0 1 0 1 37 -10.9 1.1
1 0 0 1 0 0 36 -12.0 1.2
1 0 0 0 1 1 35 -13.1 1.3
1 0 0 0 1 0 34 -14.4 0.9
1 0 0 0 0 1 33 -15.4 1.0
1 0 0 0 0 0 32 -16.4 1.1
MAX9768
10W Mono Class D Speaker
Amplifier with Volume Control
______________________________________________________________________________________ 19
Table 6. Speaker Volume Levels (continued)
V5 V4 V3 V2 V1 V0 VOLUME
POSITION
VOLUME
LEVEL (dB)
STEP SIZE
(dB)
0 1 1 1 1 1 31 -17.5 2.2
0 1 1 1 1 0 30 -19.7 1.9
0 1 1 1 0 1 29 -21.6 1.9
0 1 1 1 0 0 28 -23.5 1.7
0 1 1 0 1 1 27 -25.2 2.0
0 1 1 0 1 0 26 -27.2 2.6
0 1 1 0 0 1 25 -29.8 1.6
0 1 1 0 0 0 24 -31.5 2.0
0 1 0 1 1 1 23 -33.4 2.5
0 1 0 1 1 0 22 -36.0 1.6
0 1 0 1 0 1 21 -37.6 2.0
0 1 0 1 0 0 20 -39.6 2.5
0 1 0 0 1 1 19 -42.1 1.6
0 1 0 0 1 0 18 -43.7 2.0
0 1 0 0 0 1 17 -45.6 2.5
0 1 0 0 0 0 16 -48.1 2.5
0 0 1 1 1 1 15 -50.6 3.5
0 0 1 1 1 0 14 -54.2 2.5
0 0 1 1 0 1 13 -56.7 3.5
0 0 1 1 0 0 12 -60.2 2.5
0 0 1 0 1 1 11 -62.7 3.5
0 0 1 0 1 0 10 -66.2 2.5
0 0 1 0 0 1 9 -68.7 3.5
0 0 1 0 0 0 8 -72.2 2.5
0 0 0 1 1 1 7 -74.7 3.5
0 0 0 1 1 0 6 -78.3 2.5
0 0 0 1 0 1 5 -80.8 3.5
0 0 0 1 0 0 4 -84.3 2.5
0 0 0 0 1 1 3 -86.8 3.5
0 0 0 0 1 0 2 -90.3 2.5
0 0 0 0 0 1 1 -92.8
0 0 0 0 0 0 0 (MUTE) -161.5
MAX9768
10W Mono Class D Speaker
Amplifier with Volume Control
20 ______________________________________________________________________________________
Applications Information
Filterless Class D Operation
The MAX9768 can be operated without a filter and
meet common EMC radiation limits when the speaker
leads are less than approximately 10cm. Lengths
beyond 10cm are possible but should be verified
against the appropriate EMC standard. Select the filter-
less modulation mode with spread-spectrum modula-
tion mode for best performance.
For longer speaker wire lengths, a simple ferrite bead
and capacitor-based filter can be used to meet EMC
limits. See Figure 7 for the correct connections of these
components. Select a ferrite bead with 100Ωto 600Ω
impedance, and rated for at least 1.5A. The capacitor
value will vary based on the ferrite bead chosen and
the actual speaker lead length. Select the capacitor
value based on EMC performance.
When doing bench evaluation without a filter or a ferrite
bead filter, include a series inductor (68µH for 8Ωload)
to model the actual loudspeaker’s behavior. If this
inductance is omitted, the MAX9768 will have reduced
efficiency and output power, as well as worse THD+N
performance.
Table 7. Setting Class D Output Modulation Scheme
D7 (MSB) D6 D5 D4 D3 D2 D1 D0 (LSB) FUNCTION
1 1 0 1 0 1 0 1 Classic PWM
1 1 0 1 0 1 1 0 FILTERLESS MODULATION*
BOOT_+
C1
0.1μF
C9
330pF
C10
330pF
OUT_+
BOOT_-
C2
0.1μF
OUT_-
MAX9768
Figure 7. Ferrite Bead Filter
*
Power-on default.
Inductor-Based Output Filters
Some applications will use the MAX9768 with a full
inductor-/capacitor-based (LC) output filter. This is
common for longer speaker lead lengths, and to gain
increased margin to EMC limits. Select the PWM output
mode and use fixed-frequency modulation mode for
best audio performance. See Figure 8 for the correct
connections of these components.
The component selection is based on the load imped-
ance of the speaker. Table 8 lists suggested values for
a variety of load impedances.
Inductors L3 and L4, and capacitor C15 form the pri-
mary output filter. In addition to these primary filter
components, other components in the filter improve its
functionality. Capacitors C13 and C14, plus resistors
R6 and R7, form a Zobel at the output. A Zobel corrects
the output loading to compensate for the rising imped-
ance of the loudspeaker. Without a Zobel, the filter will
have a peak in its response near the cutoff frequency.
Capacitors C11 and C12 provide additional high-fre-
quency bypass to reduce radiated emissions.
Adjustable Gain
Gain-Setting Resistors
External feedback resistors set the gain of the
MAX9768. The output stage has an internal 20dB gain
in addition to the externally set gain. Set the maximum
gain by using resistors RFand RIN (Figure 9
)
as follows:
Choose RFbetween 10kΩand 50kΩ. Please note that
the actual gain of the amplifier is dependent on the vol-
ume level setting. For example, with the volume control
set to +9.5dB, the amplifier gain would be 9.5dB +
20dB, assuming RF= RIN.
The input amplifier can be configured into a variety of
circuits. The FB terminal is an actual operational ampli-
fier output, allowing the MAX9768 to be configured as a
summing amplifier, a filter, or an equalizer, for example.
AR
RVV
VF
IN
/=−
10
MAX9768
10W Mono Class D Speaker
Amplifier with Volume Control
______________________________________________________________________________________ 21
BOOT_+
C1
0.1μF
OUT_+ L4
4
1, 2
C11
C15
R6
MAX9768
C13
L3
14, 18
15 BOOT_-
C2
0.1μF
OUT_-
C12 R7
RL
C14
Figure 8. Output Filter for PWM Mode
Table 8. Suggested Values for LC filter
RL (Ω) L3, L4 (µH) C15 (µF) C11, C12 (µF) R6, R7 (Ω) C13, C14 (µF)
6 15 0.33 0.01 7.5 0.68
8 22 0.22 0.01 10 0.47
12 33 0.1 0.01 15 0.33
MAX9768
10W Mono Class D Speaker
Amplifier with Volume Control
22 ______________________________________________________________________________________
Power Supplies
The MAX9768 has different supplies for each portion of
the device, allowing for the optimum combination of
headroom power dissipation and noise immunity. The
speaker amplifiers are powered from PVDD and can
range from 4.5V to 14V. The remainder of the device is
powered by VDD. Power supplies are independent of
each other so sequencing is not necessary. Power may
be supplied by separate sources or derived from a sin-
gle higher source using a linear regulator to reduce the
voltage as shown in Figure 10.
Component Selection
Input Filter
An input capacitor, CIN, in conjunction with the input
resistor of the MAX9768 forms a highpass filter that
removes the DC bias from an incoming signal. The AC-
coupling capacitor allows the amplifier to automatically
bias the signal to an optimum DC level. Assuming zero
source impedance, the -3dB point of the highpass filter
is given by:
Choose CIN so f-3dB is well below the lowest frequency
of interest. Use capacitors whose dielectrics have low-
voltage coefficients, such as tantalum or aluminum elec-
trolytic. Capacitors with high-voltage coefficients, such
as ceramics, may result in increased distortion at low fre-
quencies.
Other considerations when designing the input filter
include the constraints of the overall system and the
actual frequency band of interest. Although high-fidelity
audio calls for a flat-gain response between 20Hz and
20kHz, portable voice-reproduction devices such as cel-
lular phones and two-way radios need only concentrate
on the frequency range of the spoken human voice (typi-
cally 300Hz to 3.5kHz). In addition, speakers used in
portable devices typically have a poor response below
300Hz. Taking these two factors into consideration, the
input filter may not need to be designed for a 20Hz to
20kHz response, saving both board space and cost due
to the use of smaller capacitors.
BIAS Capacitor
BIAS is the output of the internally generated DC bias
voltage. The BIAS bypass capacitor, CBIAS, improves
PSRR and THD+N by reducing power supply and other
noise sources at the common-mode bias node. Bypass
BIAS with a 2.2µF capacitor to GND.
Supply Bypassing, Layout, and Grounding
Proper layout and grounding are essential for optimum
performance. Use large traces for the power-supply
inputs and amplifier outputs to minimize losses due to
parasitic trace resistance. Large traces also aid in mov-
ing heat away from the package. Proper grounding
improves audio performance, minimizes crosstalk
between channels, and prevents any switching noise
from coupling into the audio signal. Connect PGND and
GND together at a single point on the PCB. Route all
traces that carry switching transients away from GND
and the traces/components in the audio signal path.
Bypass VDD and PVDD with a 1µF capacitor to PGND.
Place the bypass capacitors as close to the MAX9768
as possible. Place a bulk capacitor between PVDD and
PGND, if needed.
Use large, low-resistance output traces. Current drawn
from the outputs increase as load impedance decreas-
es. High output trace resistance decreases the power
delivered to the load. Large output, supply, and GND
traces allow more heat to move from the MAX9768 to
the air, decreasing the thermal impedance of the circuit
if possible.
fdB IN IN
RC
=
31
2
π
GND
GND
MAX9768
SHDN OUT
3.3V VDD
PVDD
IN
1μF
MAX1726
12V
1μF
Figure 10. Using a Linear Regulator to Produce 3.3V from a
12V Power Supply
BOOT+
OUT+
AUDIO
INPUT MAX9768
CIN
BOOT-
OUT-
IN
FB
RIN
RF
Figure 9. Setting Gain
MAX9768
10W Mono Class D Speaker
Amplifier with Volume Control
______________________________________________________________________________________ 23
Chip Information
PROCESS: BICMOS
Pin Configuration
MAX9768
10W Mono Class D Speaker
Amplifier with Volume Control
24 ______________________________________________________________________________________
24L QFN THIN.EPS
Package Information
For the latest package outline information and land patterns, go to www.maxim-ic.com/packages.
PACKAGE TYPE PACKAGE CODE DOCUMENT NO.
24 TQFN-EP T2444+4 21-0139
MAX9768
10W Mono Class D Speaker
Amplifier with Volume Control
______________________________________________________________________________________ 25
Package Information (continued)
For the latest package outline information and land patterns, go to www.maxim-ic.com/packages.
MAX9768
10W Mono Class D Speaker
Amplifier with Volume Control
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
26
____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2008 Maxim Integrated Products is a registered trademark of Maxim Integrated Products, Inc.
Heaney
Revision History
REVISION
NUMBER
REVISION
DATE DESCRIPTION PAGES
CHANGED
0 9/07 Initial release
1 3/08 Updated package outline 24, 25
2 11/08 Corrected various items 2, 4, 5, 11
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Maxim Integrated:
MAX9768BETG+ MAX9768BETG+T MAX9768ETG+ MAX9768ETG+T