MC34164, MC33164, NCV33164 Micropower Undervoltage Sensing Circuits The MC34164 series are undervoltage sensing circuits specifically designed for use as reset controllers in portable microprocessor based systems where extended battery life is required. These devices offer the designer an economical solution for low voltage detection with a single external resistor. The MC34164 series features a bandgap reference, a comparator with precise thresholds and built-in hysteresis to prevent erratic reset operation, an open collector reset output capable of sinking in excess of 6.0 mA, and guaranteed operation down to 1.0 V input with extremely low standby current. The MC devices are packaged in 3-pin TO-92 (TO-226AA), micro size TSOP-5, 8-pin SOIC-8 and Micro8TM surface mount packages. The NCV device is packaged in SOIC-8. Applications include direct monitoring of the 3.0 V or 5.0 V MPU/logic power supply used in appliance, automotive, consumer, and industrial equipment. http://onsemi.com 1 12 3 STRAIGHT LEAD BULK PACK * * Temperature Compensated Reference Monitors 3.0 V (MC34164-3) or 5.0 V (MC34164-5) Power Supplies Precise Comparator Thresholds Guaranteed Over Temperature Comparator Hysteresis Prevents Erratic Reset Reset Output Capable of Sinking in Excess of 6.0 mA Internal Clamp Diode for Discharging Delay Capacitor Guaranteed Reset Operation With 1.0 V Input Extremely Low Standby Current: As Low as 9.0 A Economical TO-92 (TO-226AA), TSOP-5, SOIC-8 and Micro8 Surface Mount Packages NCV Prefix for Automotive and Other Applications Requiring Site and Control Changes Pb-Free Packages are Available Input 5 8 1 TSOP-5 SN SUFFIX CASE 483 8 1 SOIC-8 D SUFFIX CASE 751 1 Micro8 DM SUFFIX CASE 846A PIN CONNECTIONS Reset 1 8 N.C. Input 2 7 N.C. N.C. 3 6 N.C. Ground 4 5 N.C. (Top View) TSOP-5 Pin 1. 2. 3. 4. 5. Reset 3 BENT LEAD TAPE & REEL AMMO PACK TO-92 (TO-226AA) P SUFFIX CASE 29 Features * * * * * * * * * 2 Ground Input Reset NC NC TO-92 Pin 1. Reset 2. Input 3. Ground ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 7 of this data sheet. 1.2 Vref = Sink Only Positive True Logic DEVICE MARKING INFORMATION See general marking information in the device marking section on page 8 of this data sheet. GND Figure 1. Representative Block Diagram This device contains 28 active transistors. (c) Semiconductor Components Industries, LLC, 2009 April, 2009 - Rev. 18 1 Publication Order Number: MC34164/D MC34164, MC33164, NCV33164 MAXIMUM RATINGS Symbol Value Unit Power Input Supply Voltage Rating Vin -1.0 to 12 V Reset Output Voltage VO -1.0 to 12 V Reset Output Sink Current ISink Internally Limited mA IF 100 mA PD RJA 700 178 mW C/W PD RJA 700 178 mW C/W PD RJA 520 240 mW C/W Operating Junction Temperature TJ +150 C Operating Ambient Temperature Range MC34164 Series MC33164 Series, NCV33164 TA Storage Temperature Range Tstg Clamp Diode Forward Current, Reset to Input Pin (Note 1) Power Dissipation and Thermal Characteristics P Suffix, Plastic Package Maximum Power Dissipation @ TA = 25C Thermal Resistance, Junction-to-Air D Suffix, Plastic Package Maximum Power Dissipation @ TA = 25C Thermal Resistance, Junction-to-Air DM Suffix, Plastic Package Maximum Power Dissipation @ TA = 25C Thermal Resistance, Junction-to-Air Electrostatic Discharge Sensitivity (ESD) Human Body Model (HBM) Machine Model (MM) C 0 to +70 - 40 to +125 - 65 to +150 ESD C V 4000 200 Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. MC34164-3, MC33164-3 SERIES, NCV33164-3 ELECTRICAL CHARACTERISTICS (For typical values TA = 25C, for min/max values TA is the operating ambient temperature range that applies [Notes 2 & 3], unless otherwise noted.) Characteristic Symbol Min Typ Max VIH VIL VH 2.55 2.55 0.03 2.71 2.65 0.06 2.80 2.80 - - - 0.14 0.1 0.4 0.3 6.0 12 30 - - 0.02 0.02 0.5 1.0 VF 0.6 0.9 1.2 Operating Input Voltage Range Vin 1.0 to 10 - - Quiescent Input Current Vin = 3.0 V Vin = 6.0 V Iin Unit COMPARATOR Threshold Voltage High State Output (Vin Increasing) Low State Output (Vin Decreasing) Hysteresis (ISink = 100 A) V RESET OUTPUT VOL Output Sink Saturation (Vin = 2.4 V, ISink = 1.0 mA) (Vin = 1.0 V, ISink = 0.25 mA) Output Sink Current (Vin, Reset = 2.4 V) ISink IR(leak) Output Off-State Leakage (Vin, Reset = 3.0 V) (Vin, Reset = 10 V) Clamp Diode Forward Voltage, Reset to Input Pin (IF = 5.0 mA) V mA A V TOTAL DEVICE - - 9.0 24 15 40 1. Maximum package power dissipation limits must be observed. 2. Low duty cycle pulse techniques are used during test to maintain junction temperature as close to ambient as possible. Thigh = +70C for MC34164 3. Tlow = 0C for MC34164 = - 40C for MC33164, NCV33164 = +125C for MC33164, NCV33164 http://onsemi.com 2 V A MC34164, MC33164, NCV33164 MC34164-5, MC33164-5 SERIES, NCV33164-5 ELECTRICAL CHARACTERISTICS (For typical values TA = 25C, for min/max values TA is the operating ambient temperature range that applies [Notes 5 & 6], unless otherwise noted.) Characteristic Symbol Min Typ Max Unit VIH VIL VH 4.15 4.15 0.02 4.33 4.27 0.09 4.45 4.45 - - - 0.14 0.1 0.4 0.3 7.0 20 50 - - 0.02 0.02 0.5 2.0 VF 0.6 0.9 1.2 V Operating Input Voltage Range Vin 1.0 to 10 - - V Quiescent Input Current Vin = 5.0 V Vin = 10 V Iin - - 12 32 20 50 COMPARATOR Threshold Voltage High State Output (Vin Increasing) Low State Output (Vin Decreasing) Hysteresis (ISink = 100 A) V RESET OUTPUT VOL Output Sink Saturation (Vin = 4.0 V, ISink = 1.0 mA) (Vin = 1.0 V, ISink = 0.25 mA) Output Sink Current (Vin, Reset = 4.0 V) ISink IR(leak) Output Off-State Leakage (Vin, Reset = 5.0 V) (Vin, Reset = 10 V) Clamp Diode Forward Voltage, Reset to Input Pin (IF = 5.0 mA) V mA A TOTAL DEVICE A 4. Maximum package power dissipation limits must be observed. 5. Low duty cycle pulse techniques are used during test to maintain junction temperature as close to ambient as possible. Thigh = +70C for MC34164 6. Tlow = 0C for MC34164 = - 40C for MC33164, NCV33164 = +125C for MC33164, NCV33164 7. NCV prefix is for automotive and other applications requiring site and change control. 10 RL = 82 k to Vin TA = 25C 8.0 VO , OUTPUT VOLTAGE (V) VO , OUTPUT VOLTAGE (V) 10 6.0 4.0 2.0 RL = 82 k to Vin TA = 25C 8.0 6.0 4.0 2.0 0 0 0 2.0 4.0 6.0 8.0 10 0 2.0 4.0 6.0 8.0 Vin, INPUT VOLTAGE (V) Vin, INPUT VOLTAGE (V) Figure 2. MC3X164-3 Reset Output Voltage versus Input Voltage Figure 3. MC3X164-5 Reset Output Voltage versus Input Voltage http://onsemi.com 3 10 5.0 5.0 4.0 4.0 V O , OUTPUT VOLTAGE (V) V O , OUTPUT VOLTAGE (V) MC34164, MC33164, NCV33164 3.0 2.0 1.0 3.0 2.0 1.0 RL = 82 k to Vin TA = 25C RL = 82 k to Vin TA = 25C 0 2.62 2.66 2.70 2.74 0 4.22 2.78 4.26 Vin, INPUT VOLTAGE (V) 4.36 Upper Threshold High State Output V in , THRESHOLD VOLTAGE (V) V in , THRESHOLD VOLTAGE (V) 4.38 Figure 5. MC3X164-5 Reset Output Voltage versus Input Voltage 2.76 2.72 2.68 2.64 Lower Threshold Low State Output 2.60 -50 -25 0 25 50 75 100 Upper Threshold High State Output 4.32 4.28 4.24 Lower Threshold Low State Output 4.20 -50 125 -25 0 25 50 75 100 125 TA, AMBIENT TEMPERATURE (C) TA, AMBIENT TEMPERATURE (C) Figure 6. MC3X164-3 Comparator Threshold Voltage versus Temperature Figure 7. MC3X164-5 Comparator Threshold Voltage versus Temperature 50 50 TA = 25C 40 I in, INPUT CURRENT ( A) I in, INPUT CURRENT ( A) 4.34 Vin, INPUT VOLTAGE (V) Figure 4. MC3X164-3 Reset Output Voltage versus Input Voltage 30 TA = 0C 20 TA = 70C 10 0 4.30 0 2.0 4.0 6.0 8.0 40 20 TA = 0C TA = 70C 10 0 10 TA = 25C 30 0 2.0 4.0 6.0 8.0 Vin, INPUT VOLTAGE (V) Vin, INPUT VOLTAGE (V) Figure 8. MC3X164-3 Input Current versus Input Voltage Figure 9. MC3X164-5 Input Current versus Input Voltage http://onsemi.com 4 10 MC34164, MC33164, NCV33164 4.0 Vin = 2.4 V 3.0 V OL, OUTPUT SATURATION (V) V OL, OUTPUT SATURATION (V) 4.0 TA = 70C TA = 25C 2.0 TA = 0C TA = 25C TA = 0C 1.0 TA = 70C 0 TA = 25C Vin, Reset = 4 V TA = 70C TA = 0C 3.0 TA = 25C 2.0 TA = 0C 1.0 TA = 70C 0 0 4.0 8.0 12 20 16 0 4.0 8.0 12 16 VSink, SINK CURRENT (mA) ISink, SINK CURRENT (mA) Figure 10. MC3X164-3 Reset Output Saturation versus Sink Current Figure 11. MC3X164-5 Reset Output Saturation versus Sink Current I F , FORWARD CURRENT (mA) 32 Vin = 5.0 V to 4.0 V RL = 43 k TA = 25C Reset Vin = 0 V TA = 25C 24 90% Vin 5.0 V 16 4.0 V Vin 8.0 10 % 43k 5.0V 4.0V Reset Ref 0 0 0.4 0.8 1.2 5.0 s/DIV 1.6 VF , FORWARD VOLTAGE (V) Figure 12. Clamp Diode Forward Current versus Voltage Figure 13. Reset Delay Time (MC3X164-5 Shown) R Input Power Supply Reset Microprocessor Circuit Reset CDLY 1.2 Vref tDLY = RCDLY In GND 1- 1 Vth(MPU) Vin A time delayed reset can be accomplished with the addition of CDLY. For systems with extremely fast power supply rise times (<500 ns) it is recommended that the RCDLY time constant be greater than 5.0 s. Vth(MPU) is the microprocessor reset input threshold. Figure 14. Low Voltage Microprocessor Reset http://onsemi.com 5 20 MC34164, MC33164, NCV33164 Test Data RH Iin Vin RL Power Supply Microprocessor Circuit Reset 1.2 Vref MC3X164-5 VH 4.3 RH + 0.06 RL Vth(lower) 10 RH x 10-6 GND where: RH 1.0 k 43 k RL 4.3 k VH (mV) Vth (mV) RH () RL (k) 60 103 123 160 155 199 280 262 306 357 421 530 0 1.0 1.0 1.0 2.2 2.2 2.2 4.7 4.7 4.7 4.7 4.7 0 100 100 100 220 220 220 470 470 470 470 470 43 10 6.8 4.3 10 6.8 4.3 10 8.2 6.8 5.6 4.3 Comparator hysteresis can be increased with the addition of resistor RH. The hysteresis equation has been simplified and does not account for the change of input current Iin as Vin crosses the comparator threshold (Figure 8). An increase of the lower threshold Vth(lower) will be observed due to Iin which is typically 10 A at 4.3 V. The equations are accurate to 10% with RH less than 1.0 k and RL between 4.3 k and 43 k. Figure 15. Low Voltage Microprocessor Reset With Additional Hysteresis (MC3X164-5 Shown) Input 1.0 k Input Power Supply Reset Reset Solar Cells 1.2 Vref 1.2 Vref GND GND Figure 16. Voltage Monitor Figure 17. Solar Powered Battery Charger VCC RL MTP3055EL 270 4.3V Input Reset Overheating of the logic level power MOSFET due to insufficient gate voltage can be prevented with the above circuit. When the input signal is below the 4.3 V threshold of the MC3X164-5, its output grounds the gate of the L2 MOSFET. 1.2 Vref GND MC3X164-5 Figure 18. MOSFET Low Voltage Gate Drive Protection Using the MC3X164-5 http://onsemi.com 6 MC34164, MC33164, NCV33164 ORDERING INFORMATION Package Shipping MC33164D-3G SOIC-8 (Pb-Free) 98 Units / Rail MC33164D-3R2G SOIC-8 (Pb-Free) NCV33164D-3R2* SOIC-8 Device NCV33164D-3R2G* 2500 Units / Tape & Reel SOIC-8 (Pb-Free) MC33164DM-3R2 Micro8 4000 Units / Tape & Reel MC33164DM-3R2G Micro8 (Pb-Free) MC33164P-3G TO-92 (Pb-Free) 2000 Units / Box MC33164P-3RAG TO-92 (Pb-Free) 2000 Units / Tape & Reel MC33164P-3RPG TO-92 (Pb-Free) 2000 Units / Pack MC33164D-5G SOIC-8 (Pb-Free) 98 Units / Rail MC33164D-5R2 SOIC-8 MC33164D-5R2G SOIC-8 (Pb-Free) NCV33164D-5R2G* SOIC-8 (Pb-Free) MC33164DM-5R2G Micro8 (Pb-Free) 4000 Units / Tape & Reel MC33164P-5G TO-92 (Pb-Free) 2000 Units / Box MC33164P-5RAG TO-92 (Pb-Free) 2000 Units / Tape & Reel MC33164P-5RPG TO-92 (Pb-Free) 2000 Units / Pack MC34164D-3G SOIC-8 (Pb-Free) 98 Units / Rail MC34164D-3R2G SOIC-8 (Pb-Free) 2500 Units / Tape & Reel MC34164DM-3R2G Micro8 (Pb-Free) 4000 Units / Tape & Reel MC34164P-3G TO-92 (Pb-Free) 2000 Units / Box MC34164P-3RPG TO-92 (Pb-Free) 2000 Units / Pack MC34164D-5G SOIC-8 (Pb-Free) 98 Units / Rail MC34164D-5R2G SOIC-8 (Pb-Free) 2500 Units / Tape & Reel MC34164DM-5R2G Micro8 (Pb-Free) 4000 Units / Tape & Reel MC34164SN-5T1G TSOP-5 (Pb-Free) 3000 Units / Tape & Reel MC34164P-5G TO-92 (Pb-Free) 2000 Units / Box MC34164P-5RAG TO-92 (Pb-Free) 2000 Units / Tape & Reel MC34164P-5RPG TO-92 (Pb-Free) 2000 Units / Pack 2500 Units / Tape & Reel *NCV33164: Tlow = -40C, Thigh = +125C. Guaranteed by design. NCV prefix is for automotive and other applications requiring site and change control. For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 7 MC34164, MC33164, NCV33164 PIN CONNECTIONS AND MARKING DIAGRAMS TSOP-5 SN SUFFIX CASE 483 SOIC-8 D SUFFIX CASE 751 8 5 SRCAYWG G 1 1 Micro8 MC33164DM CASE 846A 8 Micro8 MC34164DM CASE 846A 8 MIy0 AYWG G 3x164 ALYWy G 1 SRC x y A L Y W, WW G MCy0 AYWG G TO-92 MC3x164P-yRA MC3x164P-yRP MC3x164P-y CASE 29 MC3x1 64P-y YWW 1 = Device Code = Device Number 3 or 4 = Suffix Number 3 or 5 = Assembly Location = Wafer Lot = Year = Work Week = Pb-Free http://onsemi.com 8 123 MC34164, MC33164, NCV33164 PACKAGE DIMENSIONS TO-92 (TO-226AA) P SUFFIX CASE 29-11 ISSUE AM A B STRAIGHT LEAD BULK PACK R P L SEATING PLANE K D X X G J H V C SECTION X-X N 1 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. CONTOUR OF PACKAGE BEYOND DIMENSION R IS UNCONTROLLED. 4. LEAD DIMENSION IS UNCONTROLLED IN P AND BEYOND DIMENSION K MINIMUM. DIM A B C D G H J K L N P R V INCHES MIN MAX 0.175 0.205 0.170 0.210 0.125 0.165 0.016 0.021 0.045 0.055 0.095 0.105 0.015 0.020 0.500 --0.250 --0.080 0.105 --0.100 0.115 --0.135 --- MILLIMETERS MIN MAX 4.45 5.20 4.32 5.33 3.18 4.19 0.407 0.533 1.15 1.39 2.42 2.66 0.39 0.50 12.70 --6.35 --2.04 2.66 --2.54 2.93 --3.43 --- N A R BENT LEAD TAPE & REEL AMMO PACK B P T SEATING PLANE G K D X X J V 1 C N SECTION X-X http://onsemi.com 9 NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. CONTOUR OF PACKAGE BEYOND DIMENSION R IS UNCONTROLLED. 4. LEAD DIMENSION IS UNCONTROLLED IN P AND BEYOND DIMENSION K MINIMUM. DIM A B C D G J K N P R V MILLIMETERS MIN MAX 4.45 5.20 4.32 5.33 3.18 4.19 0.40 0.54 2.40 2.80 0.39 0.50 12.70 --2.04 2.66 1.50 4.00 2.93 --3.43 --- MC34164, MC33164, NCV33164 PACKAGE DIMENSIONS TSOP-5 SN SUFFIX CASE 483-02 ISSUE H D 5X NOTE 5 2X 0.10 T 2X 0.20 T NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH THICKNESS. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL. 4. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. 5. OPTIONAL CONSTRUCTION: AN ADDITIONAL TRIMMED LEAD IS ALLOWED IN THIS LOCATION. TRIMMED LEAD NOT TO EXTEND MORE THAN 0.2 FROM BODY. 0.20 C A B M 5 1 4 2 L 3 B S K DETAIL Z G A DIM A B C D G H J K L M S DETAIL Z J C 0.05 SEATING PLANE H T MILLIMETERS MIN MAX 3.00 BSC 1.50 BSC 0.90 1.10 0.25 0.50 0.95 BSC 0.01 0.10 0.10 0.26 0.20 0.60 1.25 1.55 0_ 10 _ 2.50 3.00 SOLDERING FOOTPRINT* 0.95 0.037 1.9 0.074 2.4 0.094 1.0 0.039 0.7 0.028 SCALE 10:1 mm inches *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 10 MC34164, MC33164, NCV33164 PACKAGE DIMENSIONS SOIC-8 D SUFFIX CASE 751-07 ISSUE AJ -X- NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. 751-01 THRU 751-06 ARE OBSOLETE. NEW STANDARD IS 751-07. A 8 5 S B 0.25 (0.010) M Y M 1 4 -Y- K G C N DIM A B C D G H J K M N S X 45 _ SEATING PLANE -Z- 0.10 (0.004) H D 0.25 (0.010) M Z Y S X M J S SOLDERING FOOTPRINT* 1.52 0.060 7.0 0.275 4.0 0.155 0.6 0.024 1.270 0.050 SCALE 6:1 mm inches *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 11 MILLIMETERS MIN MAX 4.80 5.00 3.80 4.00 1.35 1.75 0.33 0.51 1.27 BSC 0.10 0.25 0.19 0.25 0.40 1.27 0_ 8_ 0.25 0.50 5.80 6.20 INCHES MIN MAX 0.189 0.197 0.150 0.157 0.053 0.069 0.013 0.020 0.050 BSC 0.004 0.010 0.007 0.010 0.016 0.050 0 _ 8 _ 0.010 0.020 0.228 0.244 MC34164, MC33164, NCV33164 PACKAGE DIMENSIONS Micro8 DM SUFFIX CASE 846A-02 ISSUE H D HE PIN 1 ID NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. 846A-01 OBSOLETE, NEW STANDARD 846A-02. E e b 8 PL 0.08 (0.003) T B M S A S SEATING -T- PLANE 0.038 (0.0015) A A1 MILLIMETERS NOM MAX -- 1.10 0.08 0.15 0.33 0.40 0.18 0.23 3.00 3.10 3.00 3.10 0.65 BSC 0.40 0.55 0.70 4.75 4.90 5.05 DIM A A1 b c D E e L HE MIN -- 0.05 0.25 0.13 2.90 2.90 INCHES NOM -- 0.003 0.013 0.007 0.118 0.118 0.026 BSC 0.016 0.021 0.187 0.193 MIN -- 0.002 0.010 0.005 0.114 0.114 MAX 0.043 0.006 0.016 0.009 0.122 0.122 0.028 0.199 L c SOLDERING FOOTPRINT* 8X 1.04 0.041 0.38 0.015 8X 3.20 0.126 6X 4.24 0.167 0.65 0.0256 5.28 0.208 SCALE 8:1 mm inches *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. Micro8 is a trademark of International Rectifier. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 http://onsemi.com 12 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative MC34164/D